1250 Wood Insert - Maine Wood Stove, Gas Fireplace &

1250 Wood Insert
Owner's Manual
x
Masonry Fireplace Insert
x
Zero-Clearance (Metal)
Fireplace Insert
Save these instructions
for future reference
SAFETY NOTICE:
If this appliance is not properly installed, a house fire may
result. For your safety, follow the installation directions.
Contact local building or fire officials about restrictions and
installation inspection requirements in your area.
Travis Industries, Inc.
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275
www.travisproducts.com
¤ Copyright 2011, T.I.
$10.00
100-01233_000
4110304
Listed
Tested to: U.L. 1482 & ULC S628
2
Introduction
Introduction
We welcome you as a new owner of a 1250 wood-burning fireplace insert. In purchasing a 1250
fireplace insert you have joined the growing ranks of concerned individuals whose selection of an energy
system reflects both a concern for the environment and aesthetics. This insert is one of the finest
appliances the world over. This manual will explain the installation, operation, and maintenance of this
appliance. Please familiarize yourself with the Owner's Manual before operating your appliance and save
the manual for future reference. Included are helpful hints and suggestions which will make the
installation and operation of your new appliance an easier and more enjoyable experience. We offer our
continual support and guidance to help you achieve the maximum benefit and enjoyment from your
appliance.
Important Information
No other 1250 fireplace insert appliance has the same
serial number as yours. The serial number is
stamped onto the label on the back of the appliance.
Register your warranty online at:
This serial number will be needed in case you require
service of any type.
Or, mail your warranty card to:
Model:
traviswarranty.com
Travis Industries House of Fire
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275
1250 Fireplace Insert
Save Your Bill of Sale.
Serial Number:
Purchase Date:
Purchased From:
© Travis Industries
To receive full warranty coverage, you will
need to show evidence of the date you
purchased your heater. Do not mail your Bill
of Sale to us.
We suggest that you attach your Bill of Sale
to this page so that you will have all the
information you need in one place should the
need for service or information occur.
100-01233
4110304
Table of Contents
General Information
3
Operating Your Appliance
Introduction & Important Information .......................... 2
Safety Precautions ..................................................... 4
Features & Specifications .......................................... 6
Safety Notice .............................................................. 15
Before Your First Fire ................................................. 15
Opening the Door ....................................................... 15
Starting a Fire ............................................................ 17
Adjusting the Burn Rate ............................................. 18
Ash Removal.............................................................. 18
Blower Operation ....................................................... 19
Re-Loading the Stove ................................................ 19
Overnight Burn ........................................................... 19
Normal Operating Sounds.......................................... 19
Hints for Burning ........................................................ 20
Selecting Wood.......................................................... 20
Troubleshooting ......................................................... 21
Fireplace Insert Installation
Planning The Installation ............................................ 7
Preparation for Installation .................................... 7
Additional Accessories Needed for Installation ..... 7
Installation Considerations ................................... 7
Additional Requirements for Canada.................... 7
Fireplace Requirements ............................................. 8
Fireplace Altered Tag ................................................. 8
Insert Placement Requirements................................. 9
Hearth Requirements ................................................. 9
Masonry Fireplace Requirements .............................. 10
Zero-Clearance (Metal) Fireplace Requirements ....... 10
Drafting Performance ................................................. 11
Flue Installation.......................................................... 11
Surround Panel Installation ........................................ 12
Insert with Positive Connection .................................. 14
Insert with Direct Connection (Masonry Fireplace) ..... 14
Maintaining Your Appliance
Daily Maintenance...................................................... 22
Remove Ash .............................................................. 22
Clean The Glass ........................................................ 22
Monthly Maintenance ................................................. 23
Door and Glass Inspection ......................................... 24
Check For Creosote Buildup ...................................... 23
Yearly Maintenance ................................................... 24
Touch Up Paint .......................................................... 24
Blower Cleaning ......................................................... 24
Firebrick and Baffle Inspection................................... 24
Door Parts.................................................................. 25
Replacing the Glass ................................................... 25
Replacing the Door Gasket ........................................ 25
Replacing the Door Handle ........................................ 25
Firebox Parts.............................................................. 26
Baffle Removal and Replacement .............................. 26
Air Tube Removal and Replacement ......................... 27
Warranty ....................................................................... 28
Listing Information .................................................... 30
Index.............................................................................. 32
© Travis Industries
100-01233
4110304
4
Safety Precautions
The viewing door must be
closed and latched during
operation.
Smoke from this appliance may
active a smoke detector when
the door is open.
Gas
Gasoline or other flammable
liquids must never be used to
start the fire or "Freshen Up" the
fire. Do not store or use
gasoline or other flammable
liquids in the vicinity of this
appliance.
Never block free airflow through
the air vents on this appliance.
This appliance is designed and
approved for the burning of cord
wood only. Do not attempt to
burn any other type of fuel other
than cord wood in this
appliance, it will void all
warranties and safety listings.
Do not touch the appliance while
it is hot and educate all children
of the danger of a hightemperature appliance. Young
children should be supervised
when they are in the same room
as the appliance.
ASHES
Inspect the chimney connector
and chimney at least twice
monthly and clean if necessary.
Creosote may build up and
cause a house fire.
Do not connect this appliance to
any chimney serving another
appliance.
© Travis Industries
100-01233
Keep furniture, drapes, curtains,
wood, paper, and other
combustibles a minimum of 36"
away from the front of the
appliance.
36"
This appliance must be properly
installed to prevent the
possibility of a house fire. The
instructions must be strictly
adhered to. Do not use
makeshift methods or
compromise in the installation.
Ok
Type
HT
Ashes must be disposed in a
metal container with a tight lid
and placed on a noncombustible surface well away
from the home or structure.
Clay
Liner
Contact your local building
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance company
of this appliance as well.
This appliance must be
connected to a listed high
temperature (UL 103 HT)
residential type chimney or an
approved masonry chimney with
a standard clay tile, or stainless
steel liner.
4110304
Safety Precautions
Never try to repair or replace
any part of this appliance unless
instructions are given in this
manual. All other work must be
done by a trained technician.
Allow the appliance to cool
before carrying out any
maintenance or cleaning.
5
Do not place clothing or other
flammable items on or near this
appliance.
Do not make any changes or
modifications to an existing
masonry fireplace or chimney to
install this appliance.
Do not make any changes to the
appliance to increase
combustion air.
Maintain the door and glass seal
and keep them in good
condition.
Do not operate this heater with
broken or missing glass.
Overfiring the appliance may
cause a house fire. If a unit or
chimney connector glows, you
are overfiring.
Avoid placing wood against the
glass when loading. Do not
slam the door or strike the glass.
This
Manual
Do not throw this manual away.
This manual has important
operating and maintenance
instructions that you will need at
a later time. Always follow the
instructions in this manual.
Do not use a grate or other
device to elevate the fire off of
the firebox floor. Burn the fire
directly on the bricks.
Travis Industries, Inc. grants
no warranty, implied or
stated, for the installation or
maintenance of your
appliance, and assumes no
responsibility of any
consequential damage(s).
© Travis Industries
100-01233
4110304
6
Stove Installation (for qualified installers only)
Installation Options
Features
x
Masonry Fireplace Insert
x
Zero-Clearance (Metal) Fireplace Insert
x
x
x
x
x
x
x
EPA Phase II Approved
1.6 Cubic Foot Firebox Volume
Single Operating Control
Accepts Logs Up to 18" Long
Steel Plate Construction (Up to 3/16”)
Heavy Duty Refractory Firebrick
Optional High-Tech Blower
Heating Specifications
Approximate Maximum Heating Capacity (in square feet)*
750 to 1,200
Maximum Burn Time
Up to 8 Hours
* Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside
temperature. It is also affected by the quality and moisture level of the fuel.
Dimensions
a
5-7/8"
150mm
23-5/8"
601mm
20"
508mm
18-5/8"
474mm
13-1/2"
343mm
3"
77mm
b
Figure 1
(a) Measure side and top clearances from the top plate. Measure front clearances from the stove face
(b) Fireplace Opening
Emissions
4.4 Grams Per Hour (EPA Phase II Approved)
© Travis Industries
100-01233
4110304
Fireplace Insert Installation (for qualified installers only)
7
SAFETY NOTICE:
Please read this entire manual before you install and use your new room heater. Failure to
follow instructions may result in property damage, bodily injury, or even death. Contact
local building or fire officials about restrictions and installation inspection requirements in
your area.
Planning The Installation
We suggest that you have an authorized Travis Industries dealer install your fireplace insert. If you
install the fireplace insert yourself, your authorized dealer should review your installation plans.
Check with local building officials for any permits required for installation of this fireplace insert and
notify your insurance company before proceeding with installation.
Preparation for Installation
x
Check for damage to the exterior of the fireplace insert (dents should be reported, scratches can be
fixed by applying touch up paint).
x
Check the interior of the firebox (replace cracked firebrick and make sure baffle is in place).
The fireplace insert can be lightened by removing the firebricks and baffle - replace before operation.
Additional Accessories Needed for Installation
x
Door (shipped separately)
x
Surround Panels (see page12)
Installation Considerations
Installation Type
Considerations
Insert with Positive Flue (Full Reline) (Page 14)
REQUIRED IN CANADA
• Utilizes existing masonry or zero clearance fireplace
• Provides best draft
• Easiest to clean
• Utilizes existing masonry or zero clearance fireplace
• Provides good draft
• Requires fireplace block-off plate - see page 14
Insert with Direct Connect Flue (Page 14)
NOT APPROVED IN CANADA
Additional Requirements for Canada
x
Do not remove bricks or mortar from existing fireplace.
x
This fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from
the fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3
requirements of CAN/ULC-S636, Standard for Lining Systems for Existing Masonry or Factory-Built
Chimneys and Vents, or CAN/ULC-S640, Standard for Lining Systems for New Masonry Chimneys.
x
Permanently seal any opening between the masonry of the fireplace and the facing masonry.
x
Fireplace insert, or surround panels, may be removed to inspect fireplace insert and fireplace.
© Travis Industries
100-01233
4110304
8
Fireplace Insert Installation (for qualified installers only)
Fireplace Requirements
Figure 2 shows the minimum size requirements for the type of fireplace used.
Minimum
Fireplace Size
a Height (front)
Masonry
Fireplace
Z.C. (Metal)
Fireplace
20.75"528mm
20.75"528mm
b
Height (rear)
20.75"528mm
20.75"528mm
c
Width (front)
23.625"601mm
25.625"651mm*
d
Width (rear)
23.625"601mm
25.625"651mm*
h
e
Depth
13.5"343mm
14.5"369mm*
le
f Hearth Depth
(includes insert
depth on hearth
plus required
hearth extension)
19"483mm (US)
------------
19"483mm (US)
21"534mm
(Canada)
21"534mm
(Canada)
g
Hearth Width
39.625"1007mm 39.625"1007mm
h
Facing Width
42.625"1083mm 47.625"1210mm
i
Facing Height
32"813mm
32"813mm
j
Mantel Height
35.5"902mm
44"1118mm
Co
mb
us
tib
le
Ma
nte
l
j
No
n-C
om
bu
stib
i
Fa
cin
b
g
a
d
c
No
e
n-C
om
bu
stib
g
le
He
art
h
------------
f
Figure 2
* 1” (26mm) Clearance to fireplace walls is required for ZC Fireplaces.
Fireplace Altered Tag
Attach the "This fireplace has been altered..." plate to the fireplace (use two screws or other suitable
method). You may wish to place it in a location where it will be covered by the surround panels.
© Travis Industries
100-01233
4110304
Fireplace Insert Installation (for qualified installers only)
9
Insert Placement Requirements
x
The insert must be placed so that no combustibles are within, or can swing within (e.g. drapes,
doors), 36" (915) of the front of the insert (Figure 3 “q”).
x
Insert and hearth must be installed on a level, secure floor
x
The minimum clearances, facing, and hearth requirements in Figure 3 must be met. Follow the
clearances for the type of fireplace being used – (masonry or zero-clearance-metal).
Co
mb
us
tib
le
Ma
Minimum
Clearances
Masonry
Fireplace
Z.C. (Metal)
Fireplace
k Sidewall
13"331mm
30"762mm
l Side Facing
9.5"242mm
12"305mm
m Top Facing
12"305mm
12"305mm
n Mantel
15.5"394mm
24"610mm
16" 407mm
(US)
----------18” 458mm
(Canada)
8" 204mm
16" 407mm
(US)
----------18” 458mm
(Canada)
8" 204mm
q Front of Insert
36"
915mm
36"
915mm
x Extension Onto
Hearth
3" 77mm
3" 77mm
nte
l
Co
n
Side
Wall
mb
us
tib
le
To
pF
ac
m
ing
Fa
cin
g
o Front Hearth
(does not
include insert
extension “x”)
p Side Hearth
k
l
p
No
n-C
q
o
He mbus
art
h tible
x
o
Figure 3
Hearth Requirements
x
Must extend 16" (USA) or 18” (Canada) in front of the insert and 8" on both sides.
x
Must be non-combustible and at least .018" thick (26 gauge)
© Travis Industries
100-01233
4110304
10
Fireplace Insert Installation (for qualified installers only)
Masonry Fireplace Requirements
CANADA ONLY:
The fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from the
fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirement of
Can/ULC S635, Standard Lining Systems for Existing Masonry or Factory- Built Chimney & Vents, or
CAN/ULC S640, Standard for Lining Systems for New Masonry Chimneys.
x
Chimney must have a clay tile liner or a stainless steel liner (positive connection).
x
Entire fireplace, including chimney, must be clean and undamaged. Any damage must be repaired
prior to installation of the insert.
x
Chimney height: 15' (4.5M) minimum; 33' (10M) maximum.
x
Entire fireplace, including chimney, must meet local building requirements.
x
The fireplace insert must be placed on a masonry hearth built to UBC standards.
Zero-Clearance (Metal) Fireplace Requirements
CANADA ONLY:
The fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from the
fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirement of
Can/ULC S635, Standard Lining Systems for Existing Masonry or Factory- Built Chimney & Vents, or
CAN/ULC S640, Standard for Lining Systems for New Masonry Chimneys.
x
Must utilize a positive (full reline) or direct connection (block-off plate)
x
Must be manufactured by one of the following manufacturers:
• Marco • Majestic • Heatilator
• Heat N Glo • Lennox • Martin
• Preway • Tempco
• Monesson
• Superior
x
Entire fireplace, including chimney, must be clean and undamaged. Any damage must be repaired
prior to installation of the insert
x
Entire fireplace, including chimney, must meet local building requirements
x
Chimney height: 15' (4.5M) minimum; 33' (10M) maximum. Minimum cross section: 28.65 square
inches (18626 sq mm)
x
The damper ("A") and grate ("B") must be removed (see Figure 4). The smoke shelf ("C"), internal
baffles ("D"), screen ("E"), and metal or glass doors ("F") may be removed (if applicable). The
masonry lining ("G"), insulation ("H"), and any structured rigid frame members (metal sides, floor, door
frame, face of the fireplace, etc. – "I") may not be removed or altered
H
A
C
F
D
I
E
B
G
Figure 4
© Travis Industries
100-01233
4110304
Fireplace Insert Installation (for qualified installers only)
11
Drafting Performance
This appliance relies upon natural draft to operate. External forces, such as wind, barometric pressure,
topography, or factors of the home (negative pressure from exhaust fans, chimneys, air infiltration, etc.),
may adversely affect draft. Travis Industries can not be responsible for external forces leading to less
than optimal performance.
Leveling Bolt Installation
Two leveling bolts are included to level the insert if the fireplace has a stepped-up hearth. To install, raise
the rear of the insert up and insert the leveling bolts into the holes in the rear corners of the insert. Adjust
the bolts until they extend the same height as the hearth steps up. After the insert is installed, fine-tune
the leveling bolts to level the insert.
The leveling bolts go
This distance is the
into the holes at the
hearth step-up. The
rear corners of the
leveling bolts should
insert.
stick out this far from the
Fireplace
base of the insert.
Hearth
Figure 5
Flue Installation
x
The flue must be 6” diameter and a minimum 24 gauge black steel.
x
Use a starter section and screws to secure the flue to the insert.
© Travis Industries
100-01233
4110304
12
Fireplace Insert Installation (for qualified installers only)
Surround Panel Installation
Rectangular Panels:
SURROUND PANEL SIZE
HEIGHT
WIDTH
8"
28-1/4" 718mm
40-1/8" 1020mm
10"
30-1/4" 769mm
44-1/8" 1121mm
Installation Instructions
1.
With the insert 12” from the fireplace, install the side surround panels (see the directions below).
HINT:
Pre-thread the holes on the
insert with the screws.
Attach the side surround
ANSWER ONLY:
panels with the included
Remove and discard the
screws.
button plugs from both sides
of the insert.
2. Adjust the position of the side panels so they are: 1) flush with the bottom of the insert; 2) both the
same distance back from the front of the insert; 3) perpendicular to the floor (use the top panel, if
necessary, to judge alignment). Tighten the screws that hold the side panels in place.
© Travis Industries
100-01233
4110304
Fireplace Insert Installation (for qualified installers only)
13
3. Place the insert into the fireplace and connect the flue (if using a positive or direct connection). Install
the top panel and trim following the directions below.
Micro (1/16”)
Standard
Screwdriver
Spring
Top Trim
Clips
"L" Bracket
Top
Panel
Right Side
Trim
Optional Trim Installation:
Insert one leg of each "L" bracket into the top
and side trim piece. Align the trim to form a
precise corner, then tighten the two set
screws with a small standard screwdriver.
Slide the trim over the panels. Place the
spring clips behind the panels at the locations
shown. This keeps the trim tight against the
panel.
Optional Knock-Out
An optional knock-out is provided on both
Install the top panel so the tabs insert
sides if the power cord is routed behind the
into the joggle clips on the top panel
surround panel.
Insulation Installation (used to seal fireplace enclosure)
1. With the insert drawn 6" from the fireplace, glue the insulation strip included with the insert to the
back of the panels using RTV silicon or stove gasket cement. The insulation should be installed so it
overlaps the fireplace opening to form a seal between the panels and the fireplace face. Let the
silicon or cement dry.
2. Push the insert into the fireplace, allowing the insulation to form a seal between the panels and the
fireplace. Use a screwdriver to tuck any exposed insulation behind the panels.
© Travis Industries
100-01233
4110304
14
Fireplace Insert Installation (for qualified installers only)
Insert with
Positive
Connection
REQUIRED IN
CANADA.
Figure 6
Insert with Direct
Connection
(Masonry
Fireplace)
NOT ALLOWED IN
CANADA.
A block-off plate or
other non-combustible
sealing device (e.g.
damper adapter) is
required. It must seal
the chimney to insure
smoke does not enter
the home while
providing the chimney
system with sufficient
draft.
Figure 7
© Travis Industries
100-01233
4110304
Operating Your Appliance
15
Safety Notice
If this appliance is not properly installed, a house fire may result. For your safety, follow the installation
directions. Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
Read and follow all of the warnings on pages 4 and 5 of this manual.
Before Your First Fire
Verify the Installation
Before starting the stove, verify that the stove is properly installed and all of the requirements in this
manual have been followed.
Keep all flammable materials 36" away from the front of the stove (drapes, furniture, clothing, etc.).
Curing the Paint
2 to 4 hours
This heater uses a heat-activated paint that will emit some fumes while
starting the first fire. Open doors and windows to the room to vent these
fumes. This typically lasts two to four hours. You may also notice oil burning
off of the interior of the heater. This rust-stopping agent will soon dissipate.
Door Gasket - The door gasket might adhere to the paint on the front of the
heater. Leave the door slightly ajar for the first fire and be careful when
opening the door after the first fire.
Over-Firing the Stove
This stove was designed to operate at a high temperature. But due to differences in vent configuration,
fuel, and draft, this appliance can be operated at an excessive temperature. If the stove top or other area
starts to glow red, you are over-firing the stove. Shut the air control down to low and allow the stove to
cool before proceeding.
Over-firing may lead to damage of plated surfaces. If you are uncertain of over-firing conditions, we
suggest placing a stove thermometer (e.g. Rutland® Model 710) directly over the door on the stove top temperatures exceeding 800° are generally considered over-firing and will void the warranty.
© Travis Industries
100-01233
4110304
16
Operating Your Appliance
Opening the Door
The door becomes hot during use. Use a glove to open the door if the handle is hot.
To prevent smoke from entering the room, open the door a small amount and let air enter the firebox.
Rotate
the door
handle.
© Travis Industries
Swing
the door
open.
100-01233
4110304
Operating Your Appliance
17
Starting a Fire
Since the dawn of time man has debated the best way to start a fire. Some use the boy-scout "tee-pee",
some prefer the "tic-tac-toe" stack. Either way, review the hints and warnings below to ensure proper fire
starting.
x
Make sure the air control is pushed in. If additional air is needed, open the doors 1/4" during the first
five minutes of start-up.
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start
or "freshen up" a fire in this stove. Keep all such liquids well away from the stove while it is in use.
DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE. DO NOT BURN GARBAGE OR
FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not place such fuel
within space heater installation clearances or within the space required for charging and ash removal.
If using a firestarter, use only products specifically designed for stoves - follow the manufacturer's
instructions carefully.
HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT
MAY CAUSE SKIN BURNS.
If the smoke does not pass up the chimney, ball up one sheet of newspaper, place it in the center of the
firebox and light it. This should start the chimney drafting (this eliminates "cold air blockage").
Use plenty of kindling to ensure the stove reaches a proper temperature. Once the kindling is burning
rapidly, place a few larger pieces of wood onto the fire.
Starting a “Top-Down Fire”
One particularly successful method for starting a fire is to
stack several large pieces of wood in the center of the stove
(see the illustration to the right). Then place a several wads
of newspaper in the center with kindling on top. When you
light the newspaper this “top-down” fire will burn its way to
the center, igniting the larger pieces. With some practice,
this method should work for you.
© Travis Industries
100-01233
4110304
18
Operating Your Appliance
Adjusting the Burn Rate
Use the air control slider to control the burn rate of the stove. See the illustration below for details.
Use the air control to
change the burn rate.
Low Burn
(air control closed)
High Burn
(air control open)
Approximate Air Control Settings
Overnight Burn
Fully out to 9/32" open
Medium Burn
9/32" to 5/16" open
Medium High Burn
5/16" to 7/16" open
High Burn
7/16" open to pushed fully in
The air control becomes hot during operation - use gloves or a tool to prevent burns.
The air control may take several minutes to influence the burn rate. When making adjustments, you
may wish to let the stove burn for 10 minutes to gauge performance.
Ash Removal
ASHES
Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes
should be placed on a noncombustible floor or on the ground, away from all combustible
materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container until all cinders have thoroughly
cooled.
© Travis Industries
100-01233
4110304
Operating Your Appliance
19
Blower Operation
The blower will turn on once the stove is up to temperature. This is typically 15 to 30 minutes after
starting the fire. Follow the directions below to alter the blower speed.
OFF
HIGH
LOW
Turn the dial all the way counterclockwise until it clicks off.
The high position is all the way counterclockwise, without clicking off.
Turn the dial all the
way clockwise.
OFF
OFF
OFF
HI
LO
HI
LO
BLOWER
CONTROL
BLOWER
CONTROL
HI
LO
BLOWER
CONTROL
The blower may be used to affect heat output (i.e.: to reduce heat output, turn the blower down).
Route the power cord in a location where it will not come in contact with the appliance or become hot.
Re-Loading the Stove
Follow the directions below to minimize smoke spillage while re-loading the stove.
1
Open the air control all the way (push it in).
2
Open the door slightly. Let the airflow inside the firebox to stabilize before opening the doors fully.
3
Load wood onto the fire.
Overnight Burn
Follow the steps below to achieve an overnight burn.
1
Move the air control to high burn and let the stove become hot (burn for approximately 15 minutes).
2
Load as much wood as possible. Use large pieces if possible.
3
Let the stove burn on high for 15 minutes to keep the stove hot, then turn the air control to low.
4
In the morning the stove should still be hot, with embers in the coal bed. Stir the coals and load
small pieces of wood to re-ignite the fire, if desired.
Differences if chimney height and draft may lower overall burn times.
Normal Operating Sounds
Creaks and Clicks:
The 3/16" and 5/16" steel may creak or click when
the stove heats up and cools down - this is normal.
Blower Sounds:
The blower will make a slight "humm" as it
pushes air through the stove.
© Travis Industries
100-01233
4110304
20
Operating Your Appliance
Hints for Burning
x
Get the appliance hot before adjusting to low burn
x
Use smaller pieces of wood during start-up and high burns to increase temperature
x
Use larger pieces of wood for overnight or sustained burns
x
Stack the wood tightly together to establish a longer burn
x
Leave a bed of ashes (1/2" deep) to allow for longer burns
x
Be considerate of neighbors & the environment: burn dry wood only
x
Burn small, intense fires instead of large, slow burning fires when possible
x
Learn your appliance's operating characteristics to obtain optimum performance
Selecting Wood
x
Dry Wood is Key
x
Dry wood burns hot, emits less
smoke and creates less creosote.
x
Testing Wood Moisture
x
Split wood stored in a dry area will
be fully dry within a year. This
insures dry wood. If purchasing
wood for immediate use, test the
wood with a moisture meter. Some
experienced wood burners can
measure wood moisture by
knocking pieces together and
listening for a clear "knock" and not
a "thud".
Wet
Wood
Dry
Wood
Leads
To
Leads
To
Less
Heat
More
Heat
Leads
To
Leads
To
More Smoke
and Creostoe
Less Smoke
and Creostoe
Why Dry Wood is Key
Wet wood, when burned, must release water stored within the wood. This cools the fire, creates
creosote, and hampers a complete burn. Ask any experienced wood burner and he or she will agree: dry
wood is crucial to good performance.
Wood Cutting and Storage
Cut wood to length and
chop into quarters.
Store the wood off the ground in a
covered area. Allow for airflow
around the wood to dry the wood.
Air Flow
Air Flow
Air Flow
© Travis Industries
100-01233
4110304
Operating Your Appliance
21
Troubleshooting
Problem
Possible Cause
Smoke Enters Room During
Start-Up
x
Open the air control (pg. 18).
x
Cold Air Blockage - burn a piece of newspaper to
establish a draft.
x
If the flame is not getting enough air, a small crack in
the door is all that is needed.
x
Open the air control (pg. 18).
x
Not enough starter paper - use additional newspaper if
necessary.
x
If the flame is not getting enough air, a small crack in
the door is all that is needed.
x
Open the air control before opening the door (pg. 18).
x
Let the air stabilize before fully opening the door.
Then open the door approximately 1 inch. Let air go
into the firebox for a few seconds. Once the smoke
appears to be flowing up the chimney consistently,
open the door.
x
Insufficient Draft - Chimney height and outside
conditions can negatively affect draft. In these cases a
small amount of smoke may enter the home. Adding
more pipe or a draft-inducing cap may help.
Kindling Does Not Start - Fire
Smolders
Smoke Enters Room While ReLoading
Stove Does Not Burn Hot Enough x
Blower Does Not Run
Stove Does Not Burn Long
Enough
© Travis Industries
Wood is Wet - see the section "Selecting Wood" on
page 20 for details on wood.
x
Make sure the air control is all the way open. Slide the
control back and forth to insure the control is not stuck.
x
Insufficient Draft - Chimney height and outside
conditions can negatively affect draft. In these cases
the fire may burn slowly. Adding more pipe or a draftinducing cap may help.
x
Stove is Not Up to Temperature - This is normal. The
blower will come on when the stove is hot - usually 15
to 30 minutes.
x
Electricity is Cut to the Blower - Check the household
breaker or fuse to make sure it is operable.
x
Depending upon wood, draft, and other factors, the
burn time may be shorter then stated. Make sure the
doors are sealing and not allowing air into the firebox See the section "Door and Glass Inspection" on page
23 for details.
x
Check the ash bed for coals. Often, coals are still
glowing under a slight bed of flyash. By raking these
into a pile you can re-start your stove quickly.
100-01233
4110304
22
Maintaining Your Appliance
Failure to properly maintain and inspect your appliance may reduce the performance and life of the
appliance, void your warranty, and create a fire hazard.
Establish a routine for the fuel, wood burner and firing technique. Check daily for creosote build-up until
experience shows how often you need to clean to be safe. Be aware that the hotter the fire the less
creosote is deposited, and weekly cleaning may be necessary in mild weather even though monthly
cleaning may be enough in the coldest months. Contact your local municipal or provincial fire authority
for information on how to handle a chimney fire. Have a clearly understood plan to handle a chimney
fire.
Daily Maintenance (while stove is in use)
Remove Ash (if necessary)
x
Ash removal is not required once it builds up. 1/2" to 1" of ash may be desirable because it slows the
burn rate. Generally, remove ash once it has built up over 1". Follow the directions below to remove
ash.
1
Let the stove cool completely (at least two hours after the last coal has extinguished).
2
Place a cloth or cardboard protector over the hearth to catch ash and protect against
scratching.
3
Open the doors and scoop the ash into a metal container with a tight fitting lid. The
closed container of ashes should be placed on a noncombustible floor or on the
ground, away from all combustible materials, pending final disposal.
ASHES
Improperly disposed ashes lead to fires. Hot ashes placed in cardboard boxes, dumped in back yards,
or stored in garages, are recipes for disaster.
Wood-burning stoves are inherently dirty. During cleaning have a vacuum ready to catch spilled ash
(make sure ash is entirely extinguished).
There are vacuum cleaners specifically made to remove ash (even if the ash is warm). Contact your
dealer for details.
Clean the Glass (if necessary)
This appliance has an airwash to keep the glass clean. However, burning un-seasoned wood or burning
on lower burn rates leads to dirtier glass (especially on the sides). Do not clean glass with abrasive
cleaners. Allow the stove to fully cool before cleaning.
Apply glass cleaner or soapy water to the inside of the glass. Wipe with newspaper or a paper towel to
clean. For stubborn creosote, dip a moist paper towel or newspaper in cold ash before cleaning. The
ash acts as a mild abrasive.
Allow the stove to fully cool. Apply glass
cleaner or soapy water to the inside of
the glass. Wipe with newspaper or a
paper towel.
For Stubborn Creosote:
Dip newspaper or a paper towel
in cool ashes and wipe it on the
glass. The ash acts as a light
abrasive.
The glass will develop a very slight haze over time. This is normal and will not affect viewing of the fire.
© Travis Industries
100-01233
4110304
Maintaining Your Appliance
23
Monthly Maintenance (while appliance is in use)
Make sure the appliance has fully cooled prior to conducting service.
Door and Glass Inspection
The door can be lifted off the hinges if extensive repairs are conducted.
The door must form an air-tight seal to the firebox for the stove to work correctly. Inspect the door gasket
to make sure it forms an air-tight seal to the firebox.
High-Temperature
anti-sieze may be
Use RTV high
used on the door
temperature 600° silicone
hinges to eliminate
to adhere loose gasket.
squeaks.
If the glass is damaged, replace
Severely frayed or thread-bare
it - see “Replacement Parts” for
gasket should be replaced.
details.
The door latch should pull the door against the face of the stove (but not so tight as to not allow full
handle rotation). If the latch requires adjustment, follow the directions below.
Door Frame (with gasket)
Cam
Nut
Washers
9/16" Wrench
Door Handle
Door Cam Adjustment:
To tighten the door cam, remove the door handle and discard one of the washers
betwen the door frame and cam. To loosen the door cam, add a washer between
the door frame and cam.
Creosote - Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled
moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slowburning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote
makes an extremely hot fire. The chimney and chimney connector should be inspected at least once
every two months during the heating season to determine if a creosote buildup has occurred. If creosote
has accumulated, it should be removed to reduce the risk of a chimney fire.
If you are not certain of creosote inspection, contact your dealer or local chimney sweep for a full
inspection. Excess creosote buildup may cause a chimney fire, that may result in property damage,
injury, or death.
Operating this appliance continually at a low burn rate (air starvation) or using green (un-seasoned
wood) will increase the formation of creosote.
© Travis Industries
100-01233
4110304
24
Maintaining Your Appliance
Yearly Maintenance
Make sure the appliance has fully cooled prior to conducting service.
Touch Up Paint
Included with the owner's pack of this appliance is a can of Stove-Brite®
paint. To touch up nicks or dulled paint, apply the paint while the appliance is
cool. Sand rusted or damaged areas before preparation (use 120 grit
sandpaper). Clean and dry the area to prepare the surface. Wait at least one
hour before starting the appliance. The touched up area will appear darker
than the surrounding paint until it cures from heat. Curing will give off some
fumes while curing – open windows to ventilate.
Touch-Up
Paint
Cleaning the Air Duct and Blower (if applicable)
Use a vacuum to clean the air ducts (channels). This prevents dust from burning and creating odors.
The blower should be vacuumed every year to remove any buildup of dust, lint, etc.
Use a vacuum cleaner to
remove any buildup on the
screens of the blower.
Firebrick and Baffle Inspection
Use the illustration on page 26 as a reference for checking the following items. Make sure the appliance
is cool before proceeding.
Baffle Firebricks - check the bricks along the ceiling of the firebox to make sure they are intact and have
no gaps between them. Slide the bricks to eliminate any gaps.
Baffle Supports - make sure the front and back baffle supports in are place and not degraded. Slight
scaling or rusting of the metal is normal.
Secondary Air Tubes - Check the air tubes and collars to make sure they are intact and not severely
deteriorated. Slight scaling or rusting of the metal is normal. Make sure the push pins hold the air tubes
in place.
Floor and Wall Firebricks - replace any severely damaged firebrick along the side or floor of the firebox.
© Travis Industries
100-01233
4110304
Maintaining Your Appliance
25
Door Parts
Avalon Spokane Door
1
3
4
2
14
7
5
6
13
8
Lopi Republic Door
4
14
1
10
9
12
3
5
11
8
13
ID #
1
3
5
7
9
11
13
Description
Glass Gasket
Glass Clip w Gasket– 3 Hole
RTV High Temp. 600° Silicone
Avalon Door Handle (wood)
Lopi Glass
Lopi Door Handle Asbly
Door Cam
Qty
1
2/1
Part #
250-00173
250-00174
1
1
1
1
250-00594
250-00172
250-00171
250-00598
ID #
2
4
6
8
10
12
14
Description
Avalon Glass
Door Gasket
Avalon Door Handle Asbly
Door Washer
Glass Clip w Gasket– 2 Hole
Lopi Door Handle (spring)
Screws (8) 8-32 x 1/2” Torx
Qty
1
1
1
1
1
1
1
Part #
250-00177
250-00170
250-00818
250-00364
250-00175
250-00373
225-20039
Replacing the Glass
The glass must not contact the door retainer or glass clips directly. The glass gasket and glass clip
gaskets insulate the glass to prevent cracking. Do not over-tighten the glass clips.
Lay the glass gasket in the door frame (cut off excess gasket). Place the glass on the gasket. Secure
the glass clips to hold the glass in place (make sure the glass clip gaskets are in place).
Replacing the Door Gasket
The door gasket inserts into the outer groove of the door and is secured with RTV high-temperature 600°
silicone. Before installing, remove any residual cement. Lay the gasket in place (start at the lower left
corner) and cut off any excess gasket (do not stretch the gasket. The cement fully cures with heat from
the stove. You may need to open and close the door repeatedly to get the gasket to seat fully.
Replacing the Door Handle
See the illustration above for a component list (see pg. 23 for details on adjusting the door).
© Travis Industries
100-01233
4110304
26
Maintaining Your Appliance
Firebox Parts
5
5
2
6
3
5
4
1
5
5
5
5
5
6
5
5
7
ID #
1
3
5
Description
Baffle Support "S" Bar
Air Tube Roll Pins
Brick - 9" x 4.5" un-cut
Qty
1
6
16
7
Brick, Cut - 9" x 1.375"
2
Part #
99900294
98900357
98900102
(qty of 9)
251-00018
ID #
2
4
6
Description
Air Tube with Sleeve
Air Tube Retainer Sleeve
Brick, Cut - 9" x 2.5"
Qty
3
3
3
Part #
98900232
98900356
251-00019
Floor and Side Firebrick Removal & Replacement
Do not pry firebrick - they chip and crack easily. Remove the floor firebricks first. The side firebrick
are removed later because they are pinned in place by the floor firebrick. Clean the firebox prior to
replacing the firebrick.
© Travis Industries
100-01233
4110304
Maintaining Your Appliance
27
Baffle Removal & Replacement
The baffle is held up by the front air tube. Make sure to support the baffle after removing the air tubes.
x
Lift the four baffle firebricks then lift the baffle deflector up and over its resting postion.
x
Slide the bricks forward and tilt them downwards to remove.
Air Tube Removal & Replacement
All three air tubes are identical.
Air Tube Collar
Air Tube
a
Remove the left pin on the air tube collar
Roll Pin
b
Slide the air tube to the left, swing it
down and remove from the firebox.
© Travis Industries
100-01233
4110304
28
Limited 5 Year Warranty
Register your warranty online at traviswarranty.com. Or, mail your warranty card to:
TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275.
TRAVIS INDUSTRIES, INC. warrants this appliance (appliance is defined as the equipment manufactured by Travis
Industries, Inc.) to be defect-free in material and workmanship to the original purchaser from the date of purchase
as follows:
Check with your dealer in advance for any costs to you when arranging a warranty call.
Mileage or service charges are not covered by this warranty. This charge can vary from store to store.
Years 1 & 2 - COVERAGE: PARTS & LABOR
x
x
x
x
Firebox Assembly:
Firebox, Baffle Supports, Air Tubes, Air Channels, Convection Chamber
Door Assembly:
Cast Door, Latch Assembly, Glass Retainers
Air Control Assembly
Slider Plate, Pressure Plate
Ceramic Glass
Glass (breakage from thermal shock)
x
Firebrick
Breakage from thermal shock
x
Accessories
Legs, Pedestal, Blower
x
Re-Installation Allowance
In cases where heater must be removed from home for repairs, a partial cost of re-installation is covered
(pre-authorization required)
x
One-Way Freight Allowance
One-way freight allowance on pre-authorized repair done at factory is covered.
Exclusions: Paint, Gasketing
Years 3 THROUGH 5 - COVERAGE: PARTS & LABOR
x
Firebox Assembly:
Firebox, Baffle Supports, Air Tubes, Air Channels, Convection Chamber
x
Air Control Assembly
Slider Plate, Pressure Plate
x
Door Assembly:
Cast Door, Latch Assembly, Glass Retainers
x
One-Way Freight Allowance
One-way freight allowance on pre-authorized repair done at factory is covered.
Exclusions: Paint, Gasketing, Accessories (Legs, Pedestal, Panels, Blower), Glass, Firebrick, ReInstallation Allowance
Page 1 of 2
© Travis Industries
100-01233
4110304
Limited 5 Year Warranty
29
CONDITIONS & EXCLUSIONS
1. This new appliance must be installed by a qualified installer. It must be installed, operated, and maintained at all times in accordance with
the instructions in the Owner’s Manual. Any alteration, willful abuse, accident, neglect, or misuse of the product shall nullify this warranty.
2. This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized
Travis dealer.
3. Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and,
therefore, not covered under warranty.
4. This warranty does not cover misuse of the stove. Misuse includes over-firing (operation where the connector or stove may glow red) of this
appliance can cause serious damage and will nullify this warranty. Misuse includes use of salt saturated wood, chemically treated wood, or
any fuel not recommended in the manual.
5. Damage to the stove due to improper break-in procedures (see manual for proper break in).
6. The salt air environment of coastal areas or a high humidity environment can be corrosive to the castings. These conditions can be corrosive
and can cause the cast iron to rust. This warranty does not cover any damage caused by a salt air or high humidity environment.
7. Damage to the appliance while it is in transit is not covered by this warranty, but is subject to a claim against the common carrier.
8. The warranty, as outlined within this document, does not apply to the chimney components or other Non-Travis accessories used in
conjunction with the installation of this product. If in doubt as to the extent of this warranty, contact your authorized Travis retailer before
installation.
9. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees, buildings,
roof tops, wind, hills or mountains or negative pressure or other influences from mechanical systems such as furnaces, fans, clothes dryers,
etc.
10. This Warranty is void if:
a. The appliance has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.
b. The appliance is subject to submersion in water or prolonged periods of dampness or condensation.
c. Any damage to the appliance, combustion chamber, heat exchanger or other components due to water, or weather damage which is
the result of, but not limited to, improper chimney/venting installation.
11. Exclusions to this 5 Year Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper
installation, alteration or adjustment of the manufacturer's settings of components, lack of proper and regular maintenance, damage incurred
while the appliance is in transit, alteration, or act of God.
12. This 5 Year warranty excludes damage caused by normal wear and tear, such as paint discoloration or chipping, worn or torn gasketing,
chipped or cracked firebrick, etc. Also excluded is damage to the appliance caused by abuse, improper installation, modification of the
appliance, or the use of fuel other than that for which the appliance is configured (use cord wood only).
13. Damage to brass or plated surfaces caused by fingerprints, scratches, melted items, or other external sources left on the surfaces from the
use of abrasive cleaners is not covered in this warranty. Damage to the surfaces from over-firing (operation where the steel may glow red) is
not covered in this warranty.
14. TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials.
Incidental or consequential damages are not covered by this warranty. In some states, the exclusion of incidental or consequential damage
may not apply.
15. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Travis
appliance without the express written permission of TRAVIS INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of
approval. This warranty does not cover a stove repaired by someone other than a Travis Industries authorized dealer.
16. Any statement or representation of Travis products and their performance contained in Travis advertising, packaging literature, or printed
material is not part of this 5 year warranty.
17. This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way. If the appliance is used for
commercial purposes, it is excluded from this warranty.
18. No dealer, distributor, or similar person has the authority to represent or warrant Travis products beyond the terms contained within this
warranty. TRAVIS INDUSTRIES, INC. assumes no liability for such warranties or representations.
19. Travis Industries will not cover the cost of the removal or re-installation of hearths, facing, mantels, venting or other components.
20. If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall
remain in effect.
21. This 5 year warranty is the only warranty supplied by Travis Industries, Inc., the manufacturer of the appliance. All other warranties, whether
express or implied, are hereby expressly disclaimed and purchaser’s recourse is expressly limited to the warranties set forth herein.
IF WARRANTY SERVICE IS NEEDED:
1. If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your Travis dealer WITHIN 30 DAYS, giving
them proof of purchase, the purchase date, and the model name and serial number.
2. Travis Industries has the option of either repairing or replacing the defective component.
3. If your dealer is unable to repair your appliance’s defect, he may process a warranty claim through TRAVIS INDUSTRIES, INC.,
including the name of the dealership where you purchased the appliance, a copy of your receipt showing the date of the appliance’s
purchase, and the serial number on your appliance. At that time, you may be asked to ship your appliance, freight charges prepaid,
to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your appliance if it is
found to be defective in material or workmanship within the time frame stated within this 5 year warranty. TRAVIS INDUSTRIES,
INC. will return your appliance, freight charges (years 1 to 3) prepaid by TRAVIS INDUSTRIES, INC., to your regional distributor, or
dealership.
4. Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this
warranty. This charge can vary from store to store.
5. Any appliance or part thereof that is repaired or replaced during the limited warranty period will be warranted under the terms of the limited
warranty for a period not to exceed the remaining term of the original limited warranty or six(6) months, whichever is longer.
Page 2 of 2
© Travis Industries
100-01233
4110304
30
Listing Label
Listing Label
HOT WHILE IN OPERATION. DO NOT TOUCH. CONTACT MAY CAUSE SKIN BURNS.
KEEP FURNISHINGS AND COMBUSTIBLE MATERIAL A CONSIDERABLE DISTANCE
AWAY. SEE NAMEPLATE AND INSTRUCTIONS. DO NOT OVERFIRE. IF HEATER OR CHIMNEY CONNECTOR
GLOWS, YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY.
UNDER CERTAIN CONDITIONS OF USE, CREOSOTE BUILDUP MAY OCCUR RAPIDLY. DO NOT USE GRATE
OR ELEVATE FIRE. BUILD FIRE DIRECTLY ON HEARTH. OPERATE ONLY WITH FIREBRICK IN PLACE.
OPERATE ONLY WITH DOOR CLOSED. OPEN FEED DOORS TO FEED FIRE ONLY. USE OF OTHER FUELS
MAY DAMAGE THE HEATER AND CREATE A HAZARDOUS CONDITION.
TYPE OF FUEL: SOLID WOOD ONLY.
DO NOT REMOVE THIS LABEL
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT INSTALLATION AND RESTRICTIONS IN YOUR AREA.
SUITABLE FOR USE IN FACTORY-BUILT (Z.C.) FIREPLACES AND MASONRY FIREPLACES.
SERIAL NO:
MODEL:
CM
1250 INSERT
Report No. B0515PRT-001
Control No. 4000515
Certified for USA and Canada
Tested to: UL 1482 and ULC S628-93
MANTEL
D
A
C
B
INSERT
F
E
HEARTH
EXTENSION
Factory-Built
(Z.C.) Fireplace
Installations
30.0 in. (762 mm)
12.0 in. (305 mm)
12.0 in. (305 mm)
24.0 in. (610 mm)
16.0 in. (407 mm)
18.0 in. (458 mm)
8.0 in. (204 mm)
Masonry
Fireplace
Installations
13.0 in. (331 mm)
9.5 in. (242 mm)
12.0 in. (305 mm)
15.5 in. (394 mm)
16.0 in. (407 mm)
18.0 in. (458 mm)
8.0 in. (204 mm)
Minimum Clearance to
Combustibles and Hearth
Requirements
A.
B.
C.
D.
E. (US)
E.(Can)
F.
COMBUSTIBLE FACING
COMBUSTUBLE SIDEWALL
FACTORY-BUILT (Z.C.) FIREPLACE OR MASONRY FIREPLACE INSTALLATION
NON-COMBUSTIBLE
FIREPLACE FACING
Factory-Built (Z.C.) Fireplace installations require a minimum 24” starter section directly connected to the fireplace chimney or a full re-line.
Factory-Built (Z.C.) Fireplace chimney must have a minimum cross-sectional area of 28.85 square inches. The Factory-Built (Z.C.) Fireplace
damper and control must be removed, or secured in the open position. For minimum Factory-Built (Z.C.) Fireplace firebox size, see manufacturer’s
installation instructions. Factory-Built (Z.C.) Fireplace floor protection must be 3/8” minimum non-combustible material or equivalent, extending
16” in front of insert and 8” to both sides. A metal deflector plate must be installed if the flue collar is not completely behind the Lintel plate of the
Factory-Built (Z.C.) Fireplace openings.
PREVENT HOUSE FIRES - Install and use only in accordance with the manufacturer’s installation and operating instructions. Contact your local
building or fire officials about restrictions and installation inspection in your area. Do not connect this unit to a chimney flue serving another
appliance.
Electrical Rating:
115V., 60 Hz, 1.8 Amps
Optional Blower:
# 99000128
Do not route power cord under or in front of appliance.
Replace glass only with 5mm neoceramic or
ceramic glass.
Manufactured by:
TRAVIS INDUSTRIES, INC.
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275
www.travisproducts.com
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with July 1990 particulate emission standards.
DATE OF MANUFACTURE
2010
2011
2012
2013
Jan
Feb
Mar
Apr
May
Jun
Made in U.S.A.
© Travis Industries
Jul
Aug
Sep
Oct
Nov
Dec
0833
100-01233
4110304
Listing Information
© Travis Industries
100-01233
31
4110304
32
Index
Air Control ............................................................. 18
Air Tube Part Number ........................................... 26
Air Tube Removal & Replacement ........................ 27
Ash Disposal ......................................................... 22
Baffle Parts ........................................................... 26
Baffle Removal and Replacement .........................
Blower Cleaning .................................................... 24
Blower Does Not Run (Troubleshooting) ............... 21
Blower Operation (optional)................................... 19
Burn Rate .............................................................. 18
Chimney Cleaning ................................................. 23
Chimney Inspection (Creosote) ............................. 23
Chimney Requirements ......................................... 11
Cleaning the Ash................................................... 22
Cleaning the Glass................................................ 22
Clearances ............................................................ 9
Creosote Check .................................................... 23
Daily Maintenance................................................. 22
Dimensions ........................................................... 6
Door and Glass Inspection .................................... 23
Door Assembly ...................................................... 25
Door Gasket Replacement .................................... 25
Door Handle Replacement .................................... 25
Door Opening........................................................ 15
Door Parts ............................................................. 25
Draft Performance................................................. 11
Elbows (Chimney) ................................................. 6
Emissions .............................................................. 6
EPA Approval ........................................................ 6
Features ................................................................ 6
Fire Starting........................................................... 17
Firebox Assembly .................................................. 26
Firebox Parts ......................................................... 26
Firebrick and Baffle Inspection .............................. 24
Firebrick Removal & Replacement ........................
Floor Protection Requirements (Hearth)................ 9
Glass Cleaning...................................................... 22
Glass Replacement ............................................... 25
Hearth Requirements ............................................ 9
Heating Specifications ........................................... 6
Hints for Burns ...................................................... 20
Installation Options ................................................ 6
Listing Label .......................................................... 30
Maintenance.......................................................... 22
Monthly Maintenance ............................................ 23
Noise (Normal Operating Sounds) ........................ 19
Opening the Door .................................................. 15
Operation .............................................................. 7
Over-Firing the Stove ............................................ 15
Overnight Burn ...................................................... 19
Paint (Touch-Up Paint) .......................................... 24
Paint Curing .......................................................... 15
Re-Loading the Stove ........................................... 19
Safety Label .......................................................... 30
Safety Precautions ................................................ 4
Smell (from paint curing) ....................................... 15
© Travis Industries
Smoke Enters Room (Troubleshooting) ................ 21
Sounds (Normal Operating Sounds) ..................... 19
Starting a Fire........................................................ 17
Stove Does Not Burn Long Enough ...................... 21
Stove is Not Hot Enough (Troubleshooting) .......... 21
Table of Contents.................................................. 3
Touch-Up Paint ..................................................... 24
Troubleshooting (Operation) ................................. 21
Warranty Card ....................................................... 2
Warranty................................................................ 28
Wood..................................................................... 20
Yearly Maintenance............................................... 24
100-01233
4110304
Download PDF

advertising