Performance 2.0 Series
Warning: Excessive weight hazard!
Warning: Excessive weight
hazard!
Use two or more people to move, assemble or install cabinets and locker to avoid back injury.
Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed
incorrectly: securely attach cabinets to the wall to avoid serious injury.
For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com
Use two or more people to move, assemble, or
install cabinets and locker to avoid back injury.
Do not leave children unattended near cabinets.
High risk of tipping if cabinets are installed
incorrectly: securely attach cabinets to the
wall to avoid serious injury. For assistance, call
1.877.306.8930; for U.K 0800.031.4069: e-mail at
info@newageproducts.com.
STOP
ATTENTION: Is your cabinet damaged?
Need help or spare parts? For fastest service,
contact NewAge Products at 1-877-306-8930;
or support@newageproducts.com.
Do not return to the retailer.
R4
INDEX
Product Overview:
Unpacking - 3
Tools Needed - 3
Included Quantities - 4
Included Parts - 4
Weight Capacity - 5
Worktop Options - 5
Installation Options - 6
Installation Overview:
Floor Installation - 7
Wall Mount Installation - 8
Slatwall Installation - 9
Sets with Casters - 10
Corner Set Installation - 11
Hanging Wall Cabinets:
On Studded Wall -12
On Slatwall - 13
Securing Wall Cabinets:
To Wall - 14
To Other Cabinets - 15
Fastening Cabinets on Casters - 16
Installing Worktop:
Standard installation on cabinets - 17
Using Support Brackets - 18
Corner Worktop - 19
General Assembly:
Feet & Levelling cabinets - 20
Casters - 21
Drawers - 22
Handles - 23
Stacking - 24
Closet Rod - 25
Shelves - 26
Utility hole - 27
Magnetic Racing Stripe -28
Warranty - 29
2
Unpacking
•
•
•
•
Begin by placing the package on a covered flat surface.
Remove all cardboard, foam packaging material and clear plastic bags.
Dispose / recycle all packaging materials.
Verify all the contents in the box and gather the required tools. See “Tools Needed” , and
“Included Quantities” list.
Tools Needed
1 x 12” Magnetic Level
1 x Adjustable wrench
1 x 7/16” Socket driver wrench
1 x #2 Phillips head
screwdriver
1 x 7/16” socket
1x
6 mm or 3/16”
drill bit
1 x Cordless
Power Drill
1 x Stud Finder
1 x Pencil
1 x Tape Measure
1 x #2 Phillips Bit
1 x Hammer Drill
1 x Masonry Bit
[optional for masonry]
3
Included Quantities
Base
Cabinet
Tool
Drawer
Locker
Wall
Corner
Wall
Hardware Pack
1
1
1
1
1
Cabinet Leg
4
4
4
0
0
Leveling Foot
4
4
4
0
0
Adjustable Steel Shelves
1
0
3
0
0
Handles
2
3
2
0
0
Closet Rod
0
0
1
0
0
Locker Support Bracket
0
0
1
0
2
Joining Bracket
1
1
0
0
2
Worktop Wall Support
0
0
0
0
2
EVA Foam Drawers Liners
0
3
0
0
0
Utility Hole Grommet
1
0
1
0
0
NewAge Logo
1
1
1
1
1
Individual Parts
Adjustable Steel
Shelves
Coset Rod
Cabinet Leg
Handle
Locker
Support Bracket
Hardware Pack
Leveling
Foot
(M10 x 65mm)
4
Utility Hole
Grommet
Joining
Bracket
Hardware Pack
NewAge
Worktop
EVA Foam
Logo
Wall Support Drawer Liners
Weight
Capacity
150 lbs.
150 lbs.
100 lbs.
150 lbs.
Wall Cabinets
Max 100 lbs.
150 lbs.
200 lbs.
250 lbs per foot.
1000 lbs. per Set of 4
200 lbs.
150 lbs.
100 lbs.
200 lbs.
100 lbs.
100 lbs.
150 lbs. per 3” Caster
500 lbs. per Set of 4
200 lbs.
100 lbs.
200 lbs.
Base Cabinet
Max 600 lbs.
Tool Cabinet
Max 600 lbs.
Locker
Max 800lbs.
200 lbs.
Worktop on Cabinets
Max 200 lbs. / Cabinet
Worktop Options
21” Corner Worktop
48” Worktop. Fits over 2 Cabinets
72” Worktop. Fits over 3 Cabinets
5
Installation options for Cabinets
Important information: Please read
before beginning installation.
Option 1. - see page 7.
Floor mount with adjustable levelling legs.
• Layouts shown are only examples.All
cabinets are mobile and can be configured
in a variety of different layouts.
• Plan layout and measure space before
installing.
• Locate wall studs prior to installation.
• Consider the location of electrical outlets
when planning layout.
• Measure height of cabinets for clearence.
• Base cabinets can be mounted flush front
or flush back with Locker cabinets.
Option 2. - see page 8.
Option 3. - see page 9.
Wall mount cabinets off floor.
Wall mount on slatwall using slatwall
brackets (sold seperately).
Option 4. - see page 10
Option 5. - see page 11
Sets with casters and adjustable leveling legs.
Note: Casters cannot be installed on Locker
cabinets. Casters not included in all sets.
6
Corner set installation. Note: Corner cabinets
can be installed using all installation options.
Option 1
Floor Installation Overview
Plan layout before installing cabinets.
1
Attach feet to cabinets. See feet
installation on page 20.
• It is recommended to begin
installation with Locker cabinet.
• Cabinets must be fully secured
to wall using (4) wall screws per
cabinet.
• Casters can not be installed on
locker cabinets.
2
Begin by securing Locker cabinet to wall
in determined postion. See Page 14 for
full instructions.
3
Position and secure remaining cabinets
to wall. Install cabinets one at a time. See
page 14 for full instructions.
4
Attach cabinets together. See page 15 for
detailed fastening instructions.
5
Attach worktop. See page 17 for full
instructions.
7
Option 2
Wall Mount Installation Overview
Plan layout before installing cabinets.
1
Begin by attaching Locker cabinet to
wall. See page 12 for full instructions
on hanging cabinets.
• Determine height cabinets will be
installed off the ground.
• It is recommended to begin
installation with Locker cabinet.
• Install cabinets one at a time.
• Cabinets must be fully secured
to wall using (4) wall screws per
cabinet.
2
Position and secure remaining base
cabinets, and wall cabinets to wall.
See page 12.
4
Attach worktop. See page 17 for full
instructions.
8
3
Attach cabinets together. See page 15.
Option 3
Slatwall Installation Overview
Plan layout before installing cabinets.
1
Begin by attaching locker cabinet to
slatwall using slatwall bracket. See page
13 for slatwall hanging instructions.
3
Attach cabinets together. See page 15.
• Determine height cabinets will be
installed off the ground.
• Slatwall bracket sold seperately
• Slatwall brackets for use with
standard 3” slatwall.
• Check slatwall manufacturer for
rated load capacity.
• Do not overload.
2
Position and secure remaining base
cabinets, and wall cabinets.
4
Attach worktop. See page 17 for full
instructions.
Slatwall brackets sold separately. See
below for quantities needed.
• Locker, Tool and Base Cabinets - per
cabinet (2) x 24” Slatwall Brackets. Part
# 50979
• Wall Cabinets - per cabinet (1) x 24”
Slatwall Brackets. Part # 50979
• Corner Wall Cabinets - per cabinet (2)
x12” Slatwall Cabinets. Part # 50980
9
Option 4
Caster Set Installation Overview
Plan layout before installing cabinets.
1
Attach feet to locker cabinets. Attach
casters to base cabinets. See full
installation on pages 20 & 21.
• It is recommended to begin
installation with Locker cabinet.
• Install cabinets one at a time.
• Locker and wall cabinets must be
fully secured to wall using (4) wall
screws per cabinet.
• Casters not included in all sets.
2
Begin by securing Locker cabinet to
wall in determined postion. See Page
14 for full instructions.
4
Attach base cabinets together using
joining plate and attach worktop. See
page 16- 17.
10
3
5
Secure wall cabinets to wall and fasten together.
A gap of 2” is recommended between wall and
locker to allow clearence for cabinets on casters.
See page 14 & 15 for full instructions.
Position cabinets.
Option 5
Corner Cabinet Installation Overview
1
Attach feet to cabinets. See full feet
installation on page 20.
2
Install corner wall cabinets followed
by remaining wall cabinets. See full
instructions on pages 14.
3
Install corner worktop supports and base
cabinets. See page 19.
4
Install corner worktop. See page 19.
5
Position,secure and attach all remaining
cabinets and worktops. See pages, 14, 15
and 17.
6
11
Note:
Hanging Cabinets on
Studded Wall
1
Gather parts.
Wall Screw
(1/4” x 2.5”)
4 Wall Screws per cabinet
4 Washers per cabinet
3
ight
1
2
Use stud finder to locate the studs
and mark a line on the wall with a pencil
at desired height.
4
Attach remaining base cabinets (2),
and wall cabinets(3) to wall using same
method as locker cabinet(1)attachment.
Wall Washer
(1/4”)
Begin by attaching locker to wall. Line up
top of cabinet with pencil line(1), and predrill 3/16” (6mm) holes into studs through
holes in cabinet(2). Use wall screws to
secure to wall(3).
He
Determined
Do not load cabinet
without first securing to
the wall.
2
3
4X
per Cabinet
1
3
5
Finish by fastening cabinets together.
See page 15 for detailed instructions.
4X
per Cabinet
4X
per Cabinet
2
Masonry.
• Follow steps 3 to 5.
• Drill 4 pilot holes through the perforated
strip with hammer drill & masonry bit.
• Use 4 x (2 ¼” x ¼” )Tapcon Concrete
Anchor into wall. (Not Included)
• OR 4 x (#10 x 2” )Screw with 3/16”
masonry plug into wall. (Not Included)
• Follow Step 6.
12
Hanging Cabinets on Slatwall
Note: Slatwall Brackets for use with standard 3” slatwall Sold Separately. Check with your
slatwall supplier to determine the rated capacity of your slatwall. DO NOT OVERLOAD.
Parts Needed.
1
Insert bolts through slatwall bracket.
4
Align bolt with slots on back of cabinet
and hang cabinet.
Slatwall Bracket
Hex Bolt
(¼” x ⁵/₈”)
Washer
(¼”)
Lock Nut
(¼”)
2
Attach bracket to slatwall at desired
height.
3
Bracket Placement. Brackets needed per
cabinet. Wall - 1, Locker,Base and Tool - 2.
1.
1.
1.
2.
2.
Note:For Locker cabinet attach second
bracket 66” below first bracket.For Base
cabinet attach second bracket 18” below
first bracket.
13
Securing Cabinets on
Studded Wall
1
Use stud finder to locate the studs
and mark the wall with a pencil.
Note:
Do not load cabinet
without first securing to
the wall.
2
Gather parts.
Wall Screw
(¼” x 2½”)
Wall Washer
(¼”)
Base, Locker, Tool and Wall: 4 wall screws and 4
washers
Corner Wall: 6 wall screws and 6 washers
3
Place cabinet tight
against the wall.
6
Pre-drill (4) 1/4” (6.5mm) then drill
4 wall screws and washers through
perforated holes into studs.
4
Align cabinet
to stud marks.
X4
14
5
Level cabinet.
Masonry.
• Follow steps 3 to 5.
• Drill 4 pilot holes through the
perforated strip with hammer drill &
masonry bit.
• Use 4 x (2 ¼” x ¼” )Tapcon Concrete
Anchor into wall. (Not Included)
• OR 4 x (#10 x 2” )Screw with 3/16”
masonry plug into wall. (Not Included)
• Follow Step 6.
Fastening Cabinets
1
Note:
All drawers must be removed prior to
fastening cabinets together.See Page 22
for drawer removal instructions.
Parts Needed.
4 X Hex Bolt
(¼” x ⁵/₈”)
8 X Washer
(¼”)
2
4 X Lock nut
(¼”)
Align bolts, tighten lightly.
X4
3
Level cabinets and tighten all bolts.
15
Fastening Cabinets with Casters
Parts Needed.
8 x Foot
Attachment
Screw
2
1
2 x Joining
Brackets
Flip cabinets and push sides
together, locate holes on edges.
1
1
4
16
Open cabinets, remove any shelves,
drawers or loose items.
3
1
1
Attach casters and fasten cabinets
together. See pages 15. & 21.
5
Align holes with joining plate and attach using
foot attachment screws.
Mounting the Worktop
1
Parts Needed.
Place Worktop on cabinets. Locate the
punch holes on the tops of the cabinets.
X2
X2
I
4 x Wood Screw
#8 x 5/8
2
Drill into the worktop using the #8 x
5/8” wood screws.
3
Optional: For locker support
bracket. See Page 18.
X4
X2
17
Installing Worktop
Side Support Bracket
1
Parts Needed.
2
2 X Lock Nut
(1/4”)
2 X Hex Bolt
(.25” x 5/8”)
4 X Washer
(1/4”)
4 x Wood Screw
#8 x 5/8
Note: Support Bracket included with Lockers
A support bracket is to be used if the worktop is
added to the set without a secondary supporting
base/tool cabinet.
Open locker doors and locate holes on either side.
Align bracket holes with locker holes
and insert hex bolts through holes.
3
Tighten nuts & bolts.
X2
4
Use #8 x 5/8” wood screws and washers,
provided in the locker packaging.
5
X4
X2
18
X2
Installing Corner Worktop
Parts Needed.
6 x # 8 x 5/8”
screw
4X
Wall Screw
(1/4” x 2.5”)
1
Install Side Support Brackets on the
two base cabinets that will be adjacent
to corner worktop. See Step 2 in side
support brackets on page 18.
4 x Washer
(1/4”)
2 x Wall Support 2 x Worktop 2 X Hex Bolt
Bracket
Support Bracket (1/4” x 5/8”)
2
4
Position both cabinets in desired corner.
Locate studs and mark a level pencil line
at height of cabinets.
Position one cabinet into position and
attach corner cabinets to brackets using
#8 x 5/8” wood screws.
3
5
Align top of wall support bracket with
pencil line. Pre-drill 1/4” (6.5mm) holes,
then using (2) X 2.5 lag screw per bracket
attach corner wall support brackets into
wall studs.
Attach remaining cabinets and
countertops. See page 17.
19
Installing Feet
Parts Needed.
1
Open cabinet, remove any shelves,
drawers or loose items.
Align leg with edge of cabinet. Screw in
4 x Foot attachment screws & leveling foot.
16 x Foot Attachment
Screws
4x
M10 x 65mm
Levelling
Foot
4 x Cabinet Leg
2
Flip cabinet upside down,
locate holes at corners.
3
4
Repeat steps 3 for each corner.
5
20
Stand & level feet.
Installing Casters
Parts Needed.
4 x Casters
16 X Hex Bolt
(1/4” x 5/8”)
16 X Washer
(1/4”)
16 X Lock Nut
(1/4”)
2
Flip cabinet upside down,
locate holes forming a square.
4
Repeat step 3 for each caster.
Note: Install casters with brakes on front of
cabinet.
1
Open cabinet, remove any shelves,
drawers or loose items.
3
Align casters with holes. Attach with 4
hex bolts, washers, and nuts.
21
Installing the Drawers
Inserting Drawers.
Align Rails
Slide In
Removing Drawers.
Right Side
Left Side
22
Slide Out
Installing Handles
1
Parts Needed.
Handle
2
Align Handle to holes on doors
or drawers.
Handle Bolt
(M4 x 30mm)
Base/Locker: 2 Handles and 4 Handle Bolts
Tool Cabinet: 3 Handles and 6 Handle Bolts
3
Screw in bolts using number a #2 Philips head
screwdriver being careful not to overtighten bolts.
23
Stacking Cabinets
Parts Needed.
Note: Do not exceed weight capacity of
feet. See page page 5. Installing cabinets on
stacked cabinets is not recommended.
1
Position a second base cabinet on
top of an existing base cabinet.
3
Attach cabinets using the supplied
1/4” x 5/8” hex bolts, washers, and
nuts.
4 X Hex Bolt
(1/4” x 5/8”)
8 X Washer
(1/4”)
4 X Lock Nut
(1/4”)
2
Locate punch holes on adjoining
surface and insert bolts.
4
Tighten all bolts.
24
Inserting Locker Utility Rod
1
Tilt Rod at a slight angle.
3
Ensure Rod tabs engage in slots
on side panel when lowering into
position.
2
Insert and bring to horizontal position above slots in wall.
4
25
Inserting Cabinets Shelves
1
Stand cabinet up.
2
Insert shelf at a slight angle.
3
Rotate shelf to horizontal position.
4
Push shelf down into grooves.
5
Ensure shelf tabs engage in slots of
side panel when lowering into position
to secure.
6
Insert remaining shelves.
26
Utility Access
1
2
Insert rubber grommet into cut-out
hole in bottom panel.
Using box knife cut along perforation in
rubber grommet to create hole. Utility
hole allows easy access to electrical outlet.
27
Magnetic Racing Stripe
Note: Racing stripe not available with
diamond plate doors.
The Racing Stripe can be installed on
either door. To remove stripe follow
steps 1-3.
1
Remove the 2 plastic plugs holding in the
racing stripe at the top of door.
2
Tilt stripe off top of door.
3
Lower and remove from slot on bottom of
door.
4
Attach Racing Stripe on opposite door
following reverse order.
HANDLE WITH CARE: Racing
Stripe can easily bend and crease.
28
Manufacturer Warranty Limited Lifetime
When this product is installed, operated and maintained according to the instructions attached to or furnished with the product,
NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship
for the Lifetime of the product.
NEWAGE PRODUCTS INC. WILL NOT PAY FOR:
1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.
2. Damage resulting from improper handling or shipping of products, or products damaged by accident, misuse, abuse, fire, flood, improper installation, acts of God, neglect, corrosion, modification or mishandling.
3. Products damaged by improperly loading beyond the specified maximum weight capacity outlined in the instructions provided
with the product.
4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial
environment, or handled in anyway inconsistent with the installation instructions included with the product.
5. Cosmetic damage, including scratches, dings, dents or cracks in paint that do not affect the structural or functional capability of the product.
6. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.
7. Replacement parts for NewAge products outside Canada and the United States.
8. Replacement keys or locking mechanisms.
9. Loss of product contents due to theft, fire, flood, accident or acts of God.
10. Shipping or freight fees to deliver replacement products or to return defective products.
11. Any labor costs during the limited warranty period.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED
TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS
ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE OR PROVINCE TO PROVINCE
Thank you for purchasing a NewAge Product!
Please give us a call or visit online if you have any questions.
Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com
29