CARAT
TECHNICAL MANUAL
TM_EN
Part No.: 1764016_01
Date: 150413
CONTENT
CARAT
CONTENT.......................................................................................................................................................................2
SYMBOL DESCRIPTION.........................................................................................................................................4
Hazard intensity levels...................................................................................................................................................................................... 4
TECHNICAL SPECIFICATIONS..........................................................................................................................5
Carat 1GR........................................................................................................................................................................................................... 5
Accessories......................................................................................................................................................................................................... 5
Carat 2GR........................................................................................................................................................................................................... 6
Accessories......................................................................................................................................................................................................... 6
OVERVIEW OF COMPONENTS.......................................................................................................................7
Carat 1GR........................................................................................................................................................................................................... 7
Carat 2GR........................................................................................................................................................................................................... 8
INSTALLATION AND START UP......................................................................................................................9
Positioning........................................................................................................................................................................................................... 9
Electrical installation.......................................................................................................................................................................................... 9
Connection types............................................................................................................................................................................................... 9
Water connection............................................................................................................................................................................................ 10
Pressure and temperature............................................................................................................................................................................. 10
Starting the machine........................................................................................................................................................................................ 10
CLEANING AND CARE.......................................................................................................................................11
Coffee machine cleaning................................................................................................................................................................................. 11
Daily cleaning.................................................................................................................................................................................................... 11
Weekly cleaning................................................................................................................................................................................................ 11
Cleaning the Brewing group and porta-filter............................................................................................................................................. 12
Cleaning the gasket and shower plate......................................................................................................................................................... 13
Additional handling of the machine.............................................................................................................................................................. 14
Changing the group gasket............................................................................................................................................................................. 14
STORAGE AND DISPOSAL OF MACHINE.............................................................................................15
How to store the machine............................................................................................................................................................................ 15
Disposal of machine........................................................................................................................................................................................ 15
PROGRAMMING......................................................................................................................................................16
Electronic control panel................................................................................................................................................................................. 16
Button functions............................................................................................................................................................................................... 16
Aditional capabilities reachable from the display...................................................................................................................................... 17
Programming the coffee dosage................................................................................................................................................................... 18
Programming of hot water volume.............................................................................................................................................................. 18
Programming temperature for the turbo steamer................................................................................................................................... 18
Maximum security time.................................................................................................................................................................................. 19
Access to second level menus...................................................................................................................................................................... 19
Clock adjustment, hour, minutes and day................................................................................................................................................... 19
Auto on/off........................................................................................................................................................................................................ 20
Counters............................................................................................................................................................................................................ 21
Counters access............................................................................................................................................................................................... 21
Counter Litres.................................................................................................................................................................................................. 21
Service: Warning to technical maintenance................................................................................................................................................ 22
Total espressos................................................................................................................................................................................................. 22
Partial counter.................................................................................................................................................................................................. 23
Brewed services per keypad counter.......................................................................................................................................................... 23
Access to the technical programming......................................................................................................................................................... 23
Select language.................................................................................................................................................................................................. 24
Colour option................................................................................................................................................................................................... 24
Mode setting..................................................................................................................................................................................................... 24
2
CONTENT
CARAT
Colour setting....................................................................................................................................................................................................25
Display mode.....................................................................................................................................................................................................25
Contrast..............................................................................................................................................................................................................26
Colour ON.........................................................................................................................................................................................................26
Colour OFF........................................................................................................................................................................................................26
Name 1: Adjust the publicity message on the display (superior line)....................................................................................................27
Name 2: Adjust the publicity message on the display (inferior line)......................................................................................................27
Service pone.......................................................................................................................................................................................................27
Dosed service enabling....................................................................................................................................................................................28
Continuous brewing button...........................................................................................................................................................................28
Electronic steam wand.....................................................................................................................................................................................28
Pre-brewing........................................................................................................................................................................................................29
Adjusting the pre-brewing parameters........................................................................................................................................................29
Probe sensitivity................................................................................................................................................................................................29
Grinding notice..................................................................................................................................................................................................30
Adjusting parameters of the grinding notice..............................................................................................................................................30
Grinding notice..................................................................................................................................................................................................30
Chronometer.....................................................................................................................................................................................................31
Maintenance cycle.............................................................................................................................................................................................31
Temperatures: ºC or F.....................................................................................................................................................................................31
Boiler temperature...........................................................................................................................................................................................32
Multi boiler setting............................................................................................................................................................................................32
Groups temperature........................................................................................................................................................................................32
Offset temperature set....................................................................................................................................................................................33
PID parameters.................................................................................................................................................................................................33
Water softener filter: Regeneration.............................................................................................................................................................33
MESSAGES AND ALARMS..................................................................................................................................34
TROUBLESHOOTING...........................................................................................................................................35
ELECTRICAL DIAGRAM......................................................................................................................................36
Display board and IO-Board outputs 1Gr 230V 1+N..............................................................................................................................36
Display board and IO-Board outputs 2Gr 230V 1+N..............................................................................................................................37
Display 2Gr TS Orchestra 400V 3+N..........................................................................................................................................................38
Display 2Gr 3 boilers.......................................................................................................................................................................................39
WATER SYSTEM........................................................................................................................................................40
Machine with 1GR............................................................................................................................................................................................40
Machine with 2GR............................................................................................................................................................................................41
EXPLODED VIEW.....................................................................................................................................................42
Machine with 1GR............................................................................................................................................................................................42
Machine with 2GR............................................................................................................................................................................................44
Rotary pump......................................................................................................................................................................................................46
Boiler 1GR..........................................................................................................................................................................................................48
Boiler 2GR..........................................................................................................................................................................................................50
2Gr 3 Boilers: boiler assembly (main boiler)..............................................................................................................................................52
2Gr 3 Boilers: boiler assembly (group boiler)............................................................................................................................................54
Turbo steamer...................................................................................................................................................................................................55
Steam wand........................................................................................................................................................................................................57
Hot water outlet...............................................................................................................................................................................................59
Group head........................................................................................................................................................................................................61
Lower water system.........................................................................................................................................................................................63
Porta-filter..........................................................................................................................................................................................................65
Machine components.......................................................................................................................................................................................66
3
SYMBOL DESCRIPTION
CARAT
Hazard intensity levels
There are three different levels of hazard intensity, identified by signal words DANGER, WARNING
and IMPORTANT. The level of hazard is determined by the following definitions.
Observe the statements to ensure safety, performance, prevent injury and machine damage.
Important:
Alerts against unsafe practices. Observe to ensure drink quality, machine performance,
food safety, to prevent minor personal injury or damage to the machine.
WARNING!
Indicates a potentially hazardous situation which, if not avoided, could result in scalding,
serious injury and even death.
DANGER!
INDICATES A IMMINENTLY HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, WILL RESULT IN SERIOUS INJURY AND EVEN DEATH.
i
4
Note:
Gives additional information which may be helpful during the cleaning procedure or
operation of the machine.
TECHNICAL SPECIFICATIONS
CARAT
Carat 1GR
CARAT 1GR
FACTS
Standard
Turbo Steamer
Steam wand
2pcs
1pc
Hot water outlet
1pc
1pc
None
1pc
Turbo steamer
Electronic temperature control
Yes
Temperature control by group
Yes
Programmed via display
Yes
Stand by mode
Yes
Height, width, depth
620, 586, 563mm
Boiler volume
6L
Power supply
220-240V 1N~ 2850W 50/60 Hz
Water connection
3/8” Internal thread
Machine weight (kg)
45kg
Steam boiler operating pressure
Between 0.8 and 1.2 bar
Ambient noise
< 70 db
Accessories
2-spout
porta-filter
1-spout
porta-filter
55-cm inlet
hose
Cleaning
membrane
Drainage tube
(150 cm)
1 unit
1 unit
1 unit
1 unit
1 unit
MODEL
MINI 1GR
5
TECHNICAL SPECIFICATIONS
CARAT
Carat 2GR
CARAT 2GR
FACTS
Standard
Turbo steamer +
3Boilers
Turbo steamer
Steam wand
2pcs
1pc
Hot water outlet
1pc
1pc
None
1pc
Turbo steamer
Electronic temperature control
Yes
Temperature control by group
Yes
Programmed via display
Yes
Stand by mode
Yes
Height, width, depth
620, 774, 563mm
Boiler volume
11.5L
220-240V 1N~ 3200
W 50-60 Hz
Power supply
Water connection
11.5+2x1.5 L
220-240V 1N~ 3250
W 50-60 Hz
380-415V 3N~ 4850W
50-60Hz
380-415V 3N~ 4850W
50-60Hz
3/8” Internal thread
Machine weight (kg)
63kg
Steam boiler operating
pressure
68kg
Between 0.8 and 1.2 bar
Ambient noise
< 70 db
Accessories
2-spout
porta-filter
1-spout
porta-filter
55-cm inlet
hose
Cleaning
membrane
Drainage tube
(150 cm)
2 unit
1 unit
1 unit
1 unit
1 unit
MODEL
2GR
6
OVERVIEW OF COMPONENTS
CARAT
Front view of the machine
Carat 1GR
Steam button
Display
Hot water
button
Steam lever
Drink buttons
Turbo
Steamer
Steam
Manometer
Pump
Manometer
Main switch
Porta-filter
Hot water outlet
Cup shelf
Steam wand
Brewing group
7
OVERVIEW OF COMPONENTS
CARAT
Front view of the machine
Carat 2GR
Steam button
Drink buttons
Steam manometer
Steam lever
Steam button
Display
Brewing group
Cup shelf
Steam
wand
Hot water
outlet
Pump
manometer
8
Main switch
Porta-filter
Steam wand
INSTALLATION AND START UP
CARAT
Positioning
MIN. 10 cm
Install
the machine on a level surface. Adjust the feet to
ensure that it dispenses coffee evenly in all of the cups.
Select a level, dry, strong and stable installation surface at
least 110 cm off the floor.
Leave enough space above and behind the machine to
ensure easy cleaning and maintenance.
Do not install the machine whilst wet or damp. If wet or
damp, leave the machine until completely dry then ask
service personnel to check that none of the electrical
components are affected.
MIN. 30 cm
i
Note:
Leave an air gap of approximately 30 cm above the
machine and 10 cm behind it to ensure ventilation.
Electrical installation
The coffee machine should only be connected to the power supply by qualified
personnel. The following safety instructions should be followed at all times:
Check that the electrical specifications on the ratings plate match the specifications of
the power supply at the point of installation.
T
he coffee machine must be connected to an earthed socket that complies with the
regulations in force in the country of installation.
You should protect the electric line of the installation with a circuit breaker switch
appropriated for the power consumption of the machine, specified on its ratings plate.
A residual current circuit breaker must be installed in accordance with the
characteristics of the area of the installation.
Check the characteristics, power rating of the system and that the diameter of the
cables are suitable for the power used by the machine.
Do not connect the coffee machine to the power supply via extension boards, adapters
or shared sockets.
DANGER!
The
manufacturer will not be held liable for damage to persons, animals or
property resulting from incorrect installation of the coffee machine.
If the mains cable or plug is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid SERIOUS INJURY OR DEATH!
Connection types
Connect the machine as per the instructions on the ratings plate.
Machine: 230Vac Ph+N
Supply
230Vac Ph+N
Blue
Supply hose
Brown
Yellow/Green
Machine:
380Vac 3Ph
NEUTRAL
PHASE
Supply hose
Blue
Brown
Grey
Supply
380Vac 3Ph+N
Black
NEUTRAL
PHASE
PHASE
PHASE
Yellow/Green
9
INSTALLATION AND START UP
CARAT
Water connection
The Installation of the machine to a water mains connection must be done by a qualified person.
Rinse around 20 liters of water from the main water supply before connecting the machine to the water
connection.
Connect the inlet hose that is assembled in the machine to the main water supply, which should have
a 3/8” male connection fitted with a shut-off valve, tighten it with a wrench.
Use safe drinking water with hardness between 5ºfH and 8ºfH (French hardness degrees). If the value
is below this limit, the presence of corrosion of hydraulic components is a possibility. If the value is
higher than this limit, the presence of lime in the boiler will increase. In both cases the operation of
the machine and coffee quality will be affected negatively.
If necessary, connect the machine to a water softener or remineraliser to reduce water hardness. Use
the flexible hose that is included in the accessory box of the machine.
Connect one end of the corrugated tube to the drain cup in the machine, connect the other to the
main drainage tube at the installation area.
Important:
Only use the hoses supplied with the machine. Never reuse hoses.
Make sure that the drainage tube is not twisted and ensure that the entire tube is below the
level of the drain cup.
Pressure and temperature
B
oiler temperature and pressure are directly related (see Fig. 01).
Machine is fitted with a pressure gauge that will display the boiler pressure, if the machine is fitted
with a display it will also indicate boiler temperature.
C
o
Relationship between boiler pressure and temperature
125
120
115
BAR
110
0.8
0.9
1
0.7
Standard pressure and temperature
1.1
1.2
Fig. 01
Starting the machine
Power switch
10
Open the external supply of water to the machine.
Turn on the main power switch.
Press a drink button at the control panel on each
group, wait until water comes out continuously from
each of them. This way the heat exchangers in the
machine will be correctly filled.
Open the steam tap to release the air trapped in the
boiler.
The red lamp indicates that the boiler is heating.
The lamp switches off when the machine reaches
operating temperature.
The machine is now ready to use.
CLEANING AND CARE
CARAT
Coffee machine cleaning
Important:
T
o obtain the best efficiency, quality and performance of the machine, you should always
follow the cleaning and care instructions provided in this manual.
Turn off the power switch when cleaning the exterior of the machine.
All external surfaces should be cleaned with a wet cloth that will not get out fibers, threads or
scratch the machine.
Do not use aggressive cleaning detergents, solvents or degreasers. They can damage the
machine.
Important:
Once a day or after 8 hours from the last dispensing of coffee, the following cleaning tasks
must be performed for maintaining the quality and performance of the water system in the
machine:
Brewing Group: Place the empty porta-filter (without coffee) in the group head and
dispense hot water for one minute.
Steam wand: Position the wand outside the drip tray and open the steam lever for around
one minute.
Hot water outlet: Place a container under the water outlet and open the lever for 20
seconds.
Daily cleaning
Rinse the group and porta-filter without detergent. (only using the membrane and hot water)
Clean the external surfaces of the machine, pay special attention to the stainless steel parts.
Clean the steam wand and the water tap. Be sure that the nozzles are not blocked or half blocked
with for example milk residue. If it’s necessary to clean, be careful not to deform or damage any of
the components.
Clean the dip tray and the stainless steel insert grid under running water with a brush. You can
slowly pour 1L of hot water into the drain cup to dissolve and remove coffee residue that have
accumulated inside the cup and tubes.
Clean the group’s gasket and shower plate (page 12).
Weekly cleaning
Clean the brewing group and porta-filter with professional cleaning powder (page 11).
11
CLEANING AND CARE
CARAT
Cleaning the Brewing group and porta-filter
Unlock and remove the porta-filter from the group head.
Place the cleaning membrane in the filter basket.
Fill the filter basket with professional cleaning powder for
espresso coffee machines.
Lock the porta-filter into the group head.
Activate the auto-cleaning program:
B
A
When the machine is in idle mode, press and hold the Continuous
button (A). Directly after press the Short Espresso button (B) on
the button panel of the group that require cleaning. When cleaning
starts you may release the buttons and machine will automatically
repeat the cleaning cycles 5 times until it completed.
WARNING!
Never try to remove the porta-filter whilst the group is in cleaning operation, as the
pressurized hot water could cause scalding or serious injury. Once cleaning has finished,
wait about 3 seconds before removing the porta-filter.
Important:
Once cleaning process is finished, remove the porta-filter and run water through the
group again to rinse out all remains. Repeat the cleaning process this time without
detergent for removal of any remains of the cleaning powder, store the cleaning
membrane in a convenient place.
i
Note:
Rinse the group and porta-filter without detergent (only using the membrane and hot
water) every day.
Clean the group and porta-filter with detergent once a week.
Cleaning membrane
i
12
Professional cleaning
powder
Note:
Only use professional cleaning powder
for espresso machines. It’s avalible
from your distributor.
Part no: 1104162
CLEANING AND CARE
CARAT
Cleaning the gasket and shower plate
Cleaning the gasket
When placing the porta-filter filled with grinded coffee into the brewing group, left overs will
accumulate in the closing surface. If these remains are excessive it can prevent a good closing between
the porta-filter and the group head. Moreover, these remains can even block the dispensing of water
through the group head.
To prevent this perform the following cleaning:
Install the blind basket or gasket into the porta-filter without cleaning detergent.
Place the porta-filter in the group head, without attempting to close it.
Start a continuous espresso.
Make an opening-closing movement of the porta-filter in place without closing it. Water will now
flow around the porta-filter, flowing through the closing surface and cleaning it. Be very careful, as
this water is very hot, and can cause burns.
WARNING!
Take special care to avoid scalding when
performing this cleaning operation, as the
hot water used to clean the gasket will spill
over the sides of the porta-filter.
WARNING!
Do not fully tighten the porta-filter. If fully
tightened, high-pressure water may spray
out and cause scalding or serious injury.
Cleaning the shower plate
Remove the porta-filter from the group head.
Clean the shower and gasket with a soft brush to remove any coffee remains.
Leftover coffee
requiring cleaning
Shower plate
13
CLEANING AND CARE
CARAT
Additional handling of the machine
Important:
Avoid placing wet cups directly on the
cup shelf, it may drip into the machine
and cause machine damage.
Remove and insert the porta-filter gently.
Never use excessive force to try to close the
porta-filter.
Changing the group gasket
01
02
03
To remove the porta-filter, use a
straight-blade screwdriver to release
the shower by prying down with
medium force.
Remove the shower and gasket.
Remove and discard the old gasket.
Insert the new gasket (chamfer and
EXPOBAR logo facing up) into the
shower.
04
05 A
B
B
> 65 OC
A
15s
C
Remove the filter basket(A), then
place the new gasket and shower(B)
into the porta-filter(C).
14
99 OC
30s
Preheat the gasket to soften the rubber. A - heat the gasket for 15 seconds
using the water from the hot water outlet, or B - place the gasket, shower,
and porta-filter in hot water for 30 seconds.
CLEANING AND CARE
06
07
Insert the preheated gasket and
shower into the head group using
the porta-filter. Use both hands.
Rotate the porta-filter into its
locked position using medium force.
Use both hands.
CARAT
08
Remove the porta-filter. The new
gasket and shower will remain
inside the head group. (Do not
forget to replace the filter basket
inside the porta-filter.)
STORAGE AND DISPOSAL OF MACHINE
How to store the machine
Make all the cleaning procedures described in this manual.
Disconnect and roll up the power cord. (this should be performed by a qualified person).
D
isconnect the inlet hose from the machine to the water mains and empty the boiler. (this should be
performed by a qualified person).
Clean the drip tray and exterior of the machine.
Cover / pack the machine and store it in a dry place where it isn’t exposed to bad weather conditions.
If the machine should be used after a long period of storage, make sure to run all cleaning procedures
before using the machine again.
Disposal of machine
Make all the cleaning procedures described in this manual.
D
isconnect and roll up the power cord. (this should be performed by a qualified
person).
D
isconnect the inlet hose from the machine to the water mains and empty the
boiler. (this should be performed by a qualified person).
Clean the drip tray and exterior of the machine.
Pack and send the machine to a certified recycling center.
15
PROGRAMMING
CARAT
Electronic control panel
Button functions
Here some of the additional functions that the electronics offers:
Volume control of four different espresso drinks per brewing group.
Time-controlled hot water dispensing.
Automatic filling and level control of the boiler.
Automatic switch off of the heating element if not enough water.
System supervision through alarms.
Automatic cleaning of the brew groups
The control panel is by default programmed with 4 standard drinks (these can be reprogrammed as
you wish) and a continuous selection. The first four keys (1 short espresso, 1 long espresso, 2 short
espresso, 2 long espresso) brew the programmed volume and then stop automatically, the fifth key
brews continously untill user stops it by pressing button again.
Steam Button
Display
Shows temperature and water lever of the boiler.
Option to show time and date.
Water Button
Publicity
EXPOBAR
Max
hh:mm
day
C
o
Min
1 Short Espresso
2 Short Espresso
1 Long Espresso
2 Long Espresso
Continuous
Depending on how long this button is pressed it has 3 functions:
Less than 1 second, activates the hot water for infusions dosing.
Between 1 and 8 seconds, activates continuous espresso dispensing, in
order to stop the dispensing, press the button again.
Over 8 seconds, activates the programming menu. This is explained later
in programming part.
16
PROGRAMMING
CARAT
Aditional capabilities reachable from the display
Customizable lines
Actual temperature of the main boiler
This wave symbol
is shown when the
boiler is heating.
Publicity
EXPOBAR
hh:mm
day
Max
Actual temperature of group boilers
(Only on multi-boiler models)
C
o
T.1
96ºc
Max
Min
T.2
93ºc
hh:mm
day
C
o
Min
Boiler water level
Time & day
During espresso brewing this will show
the dispensing time or the volume of
the drink depending on what setting
you have.
Automatic switch ON/OFF; “Stand by” function.
Time management: Current day and time.
Advertising display.
Total counter of erogated espressos and hot water services (through the display).
Digital control and visualization of the temperature in the boiler.
Maximum control of temperature in the boiler through PID technology.
On-display help for reprogramming and adjusting.
Visual alarm about the need of replacing water softener filter.
Display language selection.
(OFF+ON)
Service reset
(espresso)
Group boiler OFF / ON :
Continuous + 1 long espresso:
(multi-boiler machines)
Stand by
(Only left keypad)
+
OK
Auto cleaning:
Continuous + 1 short espresso
(OFF+ON) Reset
litres of water
(descale)
17
PROGRAMMING
CARAT
Programming the coffee dosage
This section explains how to program the doses dispensed automatically by the drink buttons.
Keep the continuous button
pressed over 8 seconds, all the lights in the keypad will light up and
continuous button will flash.
Within 30 seconds press any selection that you want to reprogram (1 short espresso, 1 long espresso,
2 short espresso, 2 long espresso). Notice that all the lights will turn off except the selection you made
and the continuous button.
The group begins to dispense espresso, when the desired volume of espresso is reached, press the
selection button that is light up to stop dispensing, this volume will now be stored as default.
Repeat this process with all the selections that needs to be reprogrammed.
In case you only want to reprogram one of the selections, acts as previously described and only reprogram
one selection. The other selections will keep the existing settings.
Important:
Use a porta-filter filled with fresh coffee for every new dose you program.
i
Note:
Programming any of the options on the left-hand drink buttons (when viewing the machine
from the front) automatically sets the dispensing volumes on all of the other drink buttons. This
only applies to the left-hand drink buttons. Programming other drink buttons only modifies the
option selected.
Programming of hot water volume
Keep the continuous button
and continuous button will flash.
pressed over 8 seconds, all the lights in the keypad will light up
Press the continuous button
for less than 1 second. Water will dispense from the hot water
wand.
Press the same button
again to stop the dispensing and store the new volume. Different water
volumes can be stored in each keypad.
Programming temperature for the turbo steamer
Keep the continuous button
pressed over 8 seconds, all the lights in the keypad will light up
and continuous button will flash.
Immerse the steam wand in the liquid to be heated up.
Press the steam button
.
When the liquid reaches the desired temperature, press steam button
temperature is now stored.
again to stop. The new
When programming this button it will only affect the temperature of the liquid, not the time steaming.
Once the electronic steam wand with temperature probe reaches the programmed temperature it will
automatically turn off. Different volumes of liquid will not affect the temperature.
18
PROGRAMMING
CARAT
Maximum security time
As an additional safety, all dose settings have a maximum dispensing time of 5 minutes.
Access to second level menus
Doses Programming
Select 30s
Keep the continuous button
keypad.
(Entering first level, See fig. A). Now all the lights in the keypad will light up
and continuous button will flash. Do not release the continuous button
fig.A
Clock Adjust
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
fig.B
pressed over 8 seconds on the left
until the display shows “Clock adjust”(See fig. B). From this point we
are in the second level menu.
Enter “Clock adjust” by pressing the button
(2 short espresso) or
browse through the system with button
(1 short espresso) or
(1 long espresso).
Clock adjustment, hour, minutes and day
To adjust the clock press the button
adjust” is displayed.(See fig. C)
Clock Adjust
HH:MM Day
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
fig.C
(2 short espresso) while “Clock
The hour starts to flash, increase or decrease its value by pressing the button
(1 short espresso) or
(1 long espresso).
When the rightvalue is reached, accept it by pressing the button
(2 short espresso).
Now the minutes starts to flash, increase or decrease its value by pressing
the button
(1 short espresso) or
(1 long espresso).
When the right value is reached, accept it by pressing the button
(2 short espresso). Then the day of the week can be adjusted in
the same way (
,
&
).
When all values have been adjusted and is confirmed with button
(2 short espresso) the display will proceed to the next menu.
19
PROGRAMMING
CARAT
Auto on/off
Auto On/Off
On: Hh:mm
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
After accepting the adjusting made in the time and day by pressing the
(2 short espresso), we enter in the programming of the
button
automatic ON/OFF function of the machine.(See fig. A)
To modify the time which the machine automatically gets into the “ON”
status, while the hour is flashing, increase or decrease its value by pressing
Fig. A
(1 short espresso) or
the button
(1 long espresso).
When the right value is reached, accept it by pressing
(2 short
espresso). Then the minutes will start to flash and will be adjustable in the
i
same way (
,
&
).
Note:
By default, this first value will be: On: - - : - - this means that the function is disabled. As soon
as we modify the value, and it become different from - - : - - the function will be enabled. If we
prefer to leave this function disabled, just accept by
pressing the button
(2 short espresso) while the adjusted value is - - : - - .
Now the automatically OFF time is flashing, increase or decrease its
Auto On/Off
Off: Hh:mm
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
value by pressing the button
(1 short espresso) or
(1 long espresso). When the right value is reached, accept it by pressing the
button
(2 short espresso). Then the minutes will blink, and will
be adjustable in the same way(
,
&
). With this final
confirmation, display will proceed to the next menu.(See fig. B)
If automatic ON and OFF times have been assigned, a day off can be enabled
in which the machine will not switch on at all. The day off menu will not
appear if the automatic ON/OFF times is not set.(See fig. C)
Closed on
Day
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
i
To adjust the day OFF, increase or decrease its value by pressing the button
(1 long espresso ).
When the right value is reached, accept it by pressing the button
short espresso).
(2
Note:
By default, this first value will be: On: - - : - - this means that the function is disabled. As soon
as we modify the value, and it become different from - - : - - the function will be enabled. If we
prefer to leave this function disabled, just accept by
pressing the button
20
(1 short espresso) or
(2 short espresso) while the adjusted value is - - : - - .
PROGRAMMING
CARAT
Counters
There are 4 counters available:
Litres: litres of water which have come through the machine (help to know
when decalcifying is needed)
Service: coffee brewings needed for technical service.
Total coffee & hot water brewings
Coffee brewings per dose keypad
Counters access
Doses Programming
Select 30s
Keep the continuous button
pressed over 8 seconds, all the lights in
the keypad will light up and continuous button will flash.
The display will show:(See fig.A)
A
Clock Adjust
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Once again, press, and maintain pressed the continuous button
the display shows “Clock adjust”. (See fig.B)
till
B
Counters
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Press briefly the continuous button
“Counters”. (See fig.C)
, the display will show the option
C
Counter Litres
Water L. xxx
Total L. xxx
Counter reset
2 shorts + 2 longs
D
This counter shows the volume of water (litres), that has been through the
machine. Its main purpose is to facilitate the control of when a regeneration of
the water softener is needed.
How to access: When the display shows “counters”, accept by pressing
(two short espressos).
To exit and get to the next menu, press the continuous button
In chapter 10.31 Water softener filter: Regeneration, it can be programmed
how many litres of water the machine will use before giving the warning of
the need to regenerate the water softener. This way, the counter counts the
litres of water and warns the user when it is needed to do the regeneration
of the water softener.
21
PROGRAMMING
CARAT
To reset this counter (reset litres counter):
The espresso machine must be in the ON Status.
Turn off the machine using the main switch.
Maintain pressed both button
(2 short espresso) and
(2 long espresso), and while pressing them, turn on the espresso machine
from the main switch.
Press the continuous button
to confirm the reset.
Service: Warning to technical maintenance
Service xxx
Cof. Cycle xxx
Press Coffee cont.
Fig. A
This counter shows on the first row (See fig.A), the number of services set for
the machine to request for technical service and maintenance. On the second
row it is shown the number of services brewed (individual brewed services)
made by the machine since the last reset.
How to access: From the counter “Litres” get to this counter by pressing the
.
continuous button
To get out and get to the next menu, press the continuous button
.
It can be programmed the number of brewed services before the electronics
give the warning to make the technical maintenance.
To reset the counter (reset the service counter):
The espresso machine must be in the ON status.
Turn off the machine using the main switch.
Keep pressed both buttons
(1 short espresso) and
(1 long espresso), and while pressing them, turn on the espresso machine
from the main switch.
Press continuous button
to confirm the reset.
Total espressos
Total counter
Cof. cycle xxx
Press Coffee cont.
This totalizer adds up all the services brewed by the machine. (See fig.B)
Therefore, it cannot be reset.
How to access:
From the counter “Service”, access to this counter pressing the continuous
Fig. B
button
.
To exit and proceed to the next menu,
press the continuous button
22
.
PROGRAMMING
CARAT
Partial counter
This counter constitutes a partial counter since last reset.(See fig.A)
Partial counter
Cof. cycle xxx
Press Coffee cont.
Fig. A
Brewed services per keypad counter
This counter shows the number of brewed services brewed by each of the
possible selections of the machine. (See fig.B)
Doses type GR N
xxx
Press continuous
On the superior side of the display it is shown the dosis type (Espresso, long
espresso, 2 espressos, 2 long espressos, continuous or hot water). On the
right side it is shown which of the groups is now displayed. Underneath it is
shown the amount.
Fig. B
These counters can be reset as follow: While displays shows as fig.A, press
at the same time both buttons
(2 short espresso) and
(2
long espresso) for more than 4 seconds.
Access to the technical programming
+
-
OK
- OFF + >14s → Technical prog.
- Next Menu
The access to these adjustment menus is only possible from the left keyboard
of the machine (left, facing the machine).
With the machine in the stand by (OFF) state, keep pressed the continuous
button
for more than 15 seconds till the display shows the following
message: “Language: English” or “Lengua: Español”.
23
PROGRAMMING
CARAT
Select language
Select language
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
When on the display it is shown: “Select Language” and the selected
language(See fig.A), we can change the language used in the display.
To change the currentlanguage used, press one short espresso
(-).
or one long espresso
- Spanish - German - Italian - French - English
←(-)
(one long espresso) → (+)
(one short espresso)
To accept the selection made and proceed to the next menu, press the
continuous button
.
Colour option
CARAT Colour
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
To accept the selection made and proceed to the next menu, press the
continuous button
. (See fig.B)
Fig. B
Mode setting
CARAT Mode
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
24
(+)
To accept the selection made and proceed to the next menu, press the
continuous button
. (See fig.C)
PROGRAMMING
CARAT
Colour setting
Bar Led Colour
Colour
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
When on the display it is shown “Bar Led Colour”(See fig.A), the colour of
the led lines on the base of the machine can be adjusted. To toggle between
(+) or
the different options use the one short espresso
one long espresso
(-) buttons. The effect of the option selected can
be observed directly on the machine.
Off, red, green, blue, purple, light green, light blue, white.
←(-)
(one long espresso) → (+)
(one short espresso)
To accept the selection made and proceed to the next menu, press the
continuous button
Bar Led Colour
Mode
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
.
In this menu (See fig.B), we adjust the behavior of the led lines on the base of
the machine. To toggle the mode use the one short espresso
(+)
(-) buttons. The leds will respond immediately to
or one large coffee
the option selected.
Scrolling - Christmas – off – Fix on – blinking – dynamic ←(-)
(one long espresso) → (+)
(one short espresso)
To accept the selection made and proceed to the next menu, press the
continuous button
.
Display mode
Display Mode
Normal/reverse
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
The display has two working modes: “Normal” in which the letters are light
against a dark background, or “Reverse” or negative, in which the letter are
shaped by not lighting their shape in the background (See fig.C) .
To toggle between the two modes, use the one short espresso
(+)
(-) buttons. The effect can be seen directly on
or one long espresso
the display.
To accept the selection made and proceed to the next menu, press the
continuous button
.
25
PROGRAMMING
CARAT
Contrast
Contrast
0 - 50
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
In this menu(See fig.A), the contrast of the display lightning is set. It can be
adjusted between the values of 0 and 50. To adjust it use the one short
espresso
(+) or one long espresso
(-).
The effect can be seen directly on the display.
To accept the selection made and proceed to the next menu, press the
continuous button
.
Colour ON
Colour state ON
Colour
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
Here, the colour of the display while in “ON” state is set(See fig.B). This
means that it can be different when the machine is in the “OFF” status.
To toggle between the different options use the one short espresso
(+) or one long espresso
(-). The effect of the option
selected can be observed directly on the machine.
- Spanish - German - Italian - French - English
←(-)
(one long espresso) → (+)
(one short espresso)
To accept the selection made and proceed to the next menu, press the
continuous button
.
Colour OFF
Colour state OFF
Colour
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
Now, the colour of the display while in “OFF” state is set(See fig.C). To
toggle between the different options use the one short espresso
(+) or one long espresso
(-). The effect of the option
selected can be observed directly on the machine.
- Spanish - German - Italian - French - English
←(-)
(one long espresso) → (+)
(one short espresso)
To accept the selection made and proceed to the next menu, press the
continuous button
26
.
PROGRAMMING
CARAT
Name 1: Adjust the publicity message on the display (superior line)
Name1
AAAAAAAAAAAAAAA
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
The message shown (See fig.A) on the 2 superior lines of the display can be
adjusted here and in the following menus.
Here the first row will be adjusted.
To modify the selected letter for the blinking character press the one short
espresso
(+) or one long espresso
(-).
To accept the selected character and proceed to the next one, press the
button
(2 short espresso).
To accept the line and proceed to the next menu, press the continuousbrewing
button.
Name 2: Adjust the publicity message on the display (inferior line)
Name2
AAAAAAAAAAAAAAA
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
In this menu (See fig.B) the second row of the customizable lines is set.
To modify the selected letter for the blinking character press the one short
espresso
(+) or one long espresso
(-).
To accept the selected character and proceed to the next one, press the
button
(2 short espresso).
To accept the line and proceed to the next menu, press the continuousbrewing
button.
Service pone
Service Phone
Telephone Nr
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
In this menu (See fig.C), it is set the telephone number shown when
the warning caused by reaching the number of services set for technical
maintenance.
To modify the selected number for the blinking character press the one
short espresso
(+) or one long espresso
(-).
To accept the selected character and proceed to the next one, press the
button
(2 short espresso).
To accept the line and proceed to the next menu, press the continuous
brewing button.
27
PROGRAMMING
CARAT
Dosed service enabling
Doses setting
Enabled/disabled
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
This menu Enables/disables(See fig.A) the possibility of modifying the doses
volumes set. This is, makes it possible to disable (they will not work) the
possibility for the user to modify the doses set in the machine.
This option prevents the final user from dis-adjusting the doses set of the
machine.
To enable modifying the setting, press the button
espresso), to disable, press the button
(one short
(one long espresso).
To accept the setting and proceed to the next menu, press the
continuous button
.
Continuous brewing button
Continuous key
Option
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
This menu (See fig.B) toggles the behavior of the continuous brewing button
into different working modes.
The options are: # Tea + continuous. # Only coffee cont. # Only Tea
To modify the selected mode press the button
espresso) or
(one short
(one long espresso).
To accept the setting and proceed to the next menu, press the
continuous button
.
Electronic steam wand
Steam Boiler Gr.
N
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
In this menu, (See fig.C) it is set which keypad is phisically connected
(internally) to the button of the electronic steam wand. By factory default this
is set to 1, and it should not be modified, as malfunctioning of the machine
would occur.
Increase of decrease the value by pressing the button
short espresso) or
(one long espresso).
To accept the setting and proceed to the next menu, press the
continuous button
28
.
(one
PROGRAMMING
CARAT
Pre-brewing
Pre-brewing
Enabled/disabled
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
This setting enables or disables the electronic pre-brewing(See fig.A). By
factory default this option is disabled, as the Brilliance’s brewing groups are
equipped with mechanical pre-brewing systems.
To activate this function press the button
(one short espresso),
(one long espresso).
to disable, press the button
To accept the setting and proceed to the next menu, press the
continuous button
.
Adjusting the pre-brewing parameters
Pre-brew. ON sec
Selection type X.Xs
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
Pre-brew. OFF sec
Selection type X.Xs
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
If in the previous menu the pre-brewing function was enabled, this menus
will appear as to allow the adjusting of the parameters of the pre-brewing. As
said, this machine is already equipped with mechanical pre-brewing, so it is
not to activate this function.
On this first menu, it is adjusted the pre-brewing time for each type
of selection (short espresso, large coffee, 2 short espressos & 2 large
espressos). in which water is pumped as to moisture the grinded coffee.
To adjust it press the button
(one long espresso).
(one short espresso) or
To accept the setting and proceed to the next menu, press the continuous
button
.
Now it is adjusted the pre-brewing time for the little pause after the initial
water injection, as to allow the grinded coffee to moisture depending on
each type of selection.
To accept the setting and proceed to the next menu, press the continuous
button
.
Probe sensitivity
Probe Sensitivity
Low/Mid/High
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. D
Here it can be adjusted the detection sensibility of the level probes of the
boiler. (See fig.D)Normally it is not needed to modify it from the “medium”,
but in some cases (very pure water, this is water with very low level of
dissolved salts), it will be needed to select High sensibility and vice versa.
By default this sensibility will be set to “Med”, and generally it is not needed
to modify it.
To increase sensibility, press the button
decrease it, press the button
(one short espresso), to
(one long espresso).
To accept the setting and proceed to the next menu, press the continuous
button
.
29
PROGRAMMING
CARAT
Grinding notice
Grinding Notice
Enabled/disabled
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
This setting enables or disables the brewing monitor(See fig.A). This function
analyzes the output flow when brewing, and depending on it, advises if the
grinded coffee is too thin or too coarse. If the brewing flowrate was between
limits, it will display “Ok” at the end of the brewing process.
To enable it, press the button
press the button
(one short espresso), to disable it, (one long espresso).
To accept the setting and proceed to the next menu, press the continuous
button
.
Adjusting parameters of the grinding notice
Thin Grinding
X.X
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
If in the previous section the grinding notice was enabled, in this menu, its
parameters can be adjusted. If it was disabled, this menu will not appear.
Here it is adjusted the minimum flow rate that will be considered as inferior
limit of a good brewing flowrate.
To increase this value, press the button
to decrease it, press the button
Thick Grinding
X.X
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
(one short espresso),
(one long espresso).
To accept the setting and proceed to the next menu, press the
continuous button
.
Here it is adjusted the maximum flow rate that will be considered as superior
limit of a good brewing flowrate.
To increase this value, press the button
to decrease it, press the button
(one short espresso),
(one long espresso).
To accept the setting and proceed to the next menu, press the continuous
button
.
Grinding notice
Led Idle
option
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. D
The blinking of the keypads lights have different behavior modes that can
be toggled by pressing the button
(one long espresso).
The options are: Enabled, disabled & Rotation leds.
To accept the setting and proceed to the next menu, press the continuous
button
30
(one short espresso) and
.
PROGRAMMING
CARAT
Chronometer
Crono
option
The displays (See fig.A) of each group have different working modes:
Brewing chronometer: When brewing an espresso, the display acts as a
chronometer measuring the time taken to erogate the espresso.
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Pulses: When brewing an espresso, the displays acts as a volume counter
showing the volume brewed in cubic centimeters.
Fig. A
Disabled: Easch group display is not affected when brewing espresso.
To change between the different option use press the button
short espresso) or
(one
(one long espresso).
To accept the setting and proceed to the next menu, press the continuous
button
.
Maintenance cycle
Maintenance cycle
XXXX
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
Here it is adjusted the Number of espresso brewings needed for maintenance
cycle, (shower screen replacing, gaskets, etc.) When the service counter
reaches the number set here, on the display it is shown the warning “Service
needed”, and the Phone of the service.
To increase this value, press the button
to decrease it, press the button
(one short espresso),
(one long espresso).
To accept the setting and proceed to the next menu, press the continuous
button
.
Temperatures: ºC or F
Temperature
ºC/ºF
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
To show the temperature in ºF (Fahrenheit) press the button
short espresso),
To show the temperature in ºC (Celsius) press the button
long espresso).
(one
(one
To accept the setting and proceed to the next menu, press the continuous
button
.
31
PROGRAMMING
CARAT
Boiler temperature
Boiler temperature
XXºC
YYYºF
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. A
In this section the temperature of the boiler is set.
To increase temperature, press the button
to decrease it, press the button
(one short espresso),
(one long espresso).
To accept the setting and proceed to the next menu, press the continuous
button
.
Multi boiler setting
Heating Group
XXXX
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. B
Here is set the actual number of extra boilers that the machine has.This
setting is factory set, and must not be modified, as this would cause a
malfunctioning.
To modify the setting press the button
or
(one short espresso),
(one long espresso). The options are:
- GR1+GR2 (One main boiler and 2 groups boilers)
- OFF (Only one main boiler machine)
To accept the setting and proceed to the next menu, press the continuous
button
.
Groups temperature
Group temperature
XXºC
YYYºF
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
Fig. C
Here it is adjusted the temperature for each group and the main boiler. If the
previous menu was set to “OFF”, only the temperature for the main boiler
will appear in this menus.
To increase temperature value, press the button
espresso), to decrease it, press the button
(one short
(one long espresso).
Group temperature1 – Group temperature2 – Main boiler temperature
Once adjusted each temperature, press the continuous button
to adjust the next group/boiler temperature.
Once set the temperature of the last group/boiler, when pressing the
continuous button
32
it will procceed to the next menu.
as
PROGRAMMING
CARAT
Offset temperature set
In this setting it is set the temperature offset to be considered between the
group boiler and the group head. If the Grupos Calefactados (multicaldera)
was set to “OFF”, this menu will not appear.
OFFST Tset Coffee
XXºC
YYYºF
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
This parameter is factory set to 10ºC, and it is recommended not to modify
it.
To increase temperature drop, press the button
(one short
Fig. A
espresso), to decrease it, press the button
(one long espresso).
To accept the setting and proceed to the next menu, press the continuous
.
button
PID parameters
In this menu the PID internal parameters are set. This parameters are factory
set and they must not be modified, as doing so will cause the machine to
malfunction. By default they are: kP=4, kI=0,07, kD=2,2.
KP KI KD
4 0,07 2,2
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
To adjust each parameter, press the button
(one long espresso).
espresso) and
Fig. B
(one short
Once adjusted each parameter, press the continuous button
to proceed to the next parameter. When having adjusted the last one, when
pressing the continuous button, the next menu will appear..
Water softener filter: Regeneration
Here it is adjusted the liters of water after which the electronics will warn
about the need of regenerating the water softener.
Water filter
NNN
1 short espresso ↑ +
1 long espresso ↓ 2 short espresso OK
Continuous to confirm
To increase this number, press the button
to decrease it, press the button
Fig. C
(one short espresso),
(one long espresso).
In Contador Litros chapter it is shown the volume of water already used
by the machine since last reset.
To accept the setting and proceed to the next menu, press the continuous
.
button
Model of
water softener
Quantity of water treated depending on water hardness
(water hardnes units: french degrees)
20º
30º
L8
1200
1000
L 12
1900
1500
40º
Salt
60º
80º
KG
900
700
500
1
1350
1050
750
1.5
Approximated litres of water treated until regeneration of the water softener is needed.
33
MESSAGES AND ALARMS
Alarm flowmeter
X
CARAT
Flowmeter X failure / No flow detected in flowmeter X
C
o
Max
Min
No water
Check that the machine is receiving water.
C
o
Max
Min
Tprobe Unconnect
X
Temperature sensor X fault.
C
o
Max
Min
Service
9999999
Warning technical service needed.
C
o
Max
Min
Filter
999999999
Max
Min
34
The water softener filter needs to be replaced.
C
o
TROUBLESHOOTING
CARAT
The following checks can be carried out by users once the machine has been turned off and disconnected
from the power supply. For all other non-specified machine faults, disconnect the machine from the power
supply and immediately contact authorised and qualified service personnel.
Problem
Possible cause
Solution
The plug is not correctly
inserted into the power socket
Check that the plug is correctly
inserted and that the power
socket is operational.
The circuit breaker and/or
differential are disconnected.
Check that they are connected.
The cable and/or plug are
damaged.
Call service personnel to
replace them.
The steam wand does not
dispense steam
The steam wand is clogged by
milk
Clean the wand and, if
necessary, remove the nozzle
and unclog it using a pin or
needle.
Water is found underneath
the machine
The drainage tube is blocked.
Clean the drainage tube.
The machine does not start up
Faults produced by limescale
Coffee not dispensed at right temperature:
Heat-exchanger outlet pipes clogged by limescale.
Brewing groups do not dispense water:
Water system is clogged by limescale.
90% of faults are due to limescaling inside the coffee machine (due to not softening the water). To avoid
these faults, maintain the water softener regularly.
Coffee-grinding problems
Coffee dispensing is very fast:
The coffee grinding is to coarse. Adjust the coffeegrinding setting.
Coffee dispensing is very slow:
The coffee grinding is to fine. Adjust the coffeegrinding setting.
35
36
4
1
3
Power Switch
PN.1660036
C10200141
Thermal Cut-out 1
Pole with bulb
2
G
1660097
Contactor 230v LC1D18P7C
L
N
Thermal-link
2500W-230V- 6ltrs.COPPER ELEMENT
PN.C38025001
1/L1
2/T1
L2
T2
PN.1660084
Capacitor 0.47uF
T1
L1
4/A2
3/A1
Solid state relay
PN.C60800101
T3
A2
A1
L3
8X2
4
OUT 3
OUT 2
OUT 1
SLmin
SLiv
+(Vcc)
Gnd
8X2
8X2
Main PCB
PN. 60100420
OPTIONAL CAPUCINADOR WITH PERISTALTIC PUMP
Drink keypad
PN.1264127
NTC steamer
Ref. 60100075
NTC Boiler
Ref. 60100076
Flow meter
PN.60100045
S.T.C.(Boiler)
5X2
Display module
PN.2760031
N
~
F
EvI.V.
EvA.I.
EvA.I.
EvC.C.
EvG.3
EvG.2
EvG.1
M
COMMON
MAIN SUPLY
Electro valve
PN.60000120
Electro valve
PN.60000100
Electro valve
PN.60000105
Electro valve
PN.60000112
+
-
+
C.C.R.
Air pump
Ref. 60100049
Ref. 60000049
OPTIONAL CAPUCINADOR WITH PERISTALTIC PUMP
-
+
M
Motor
PN.60000016
ELECTRICAL DIAGRAM
CARAT
Display board and IO-Board outputs 1Gr 230V 1+N
Water level sensor
PN.60100040
4
1
3
Power Switch
PN.1660036
2
C10200150
Thermal Cut-out 3
Pole with bulb
G
1660097
Contactor 230v LC1D18P7C
L
N
Thermal-link
3050W.230V- 2gr ELEMENT
PN.C38027000F
4/A2
1/L1
L2
PN.1660084
Capacitor 0.47uF
T1
L1
3/A1
2/T1
Solid state relay
PN.C60800101
T2
T3
A2
A1
L3
NTC steamer
Ref. 60100075
NTC Boiler
Ref. 60100076
Drink keypad
PN.1264124
8X2
Flow meter
PN.60100045
S.T.C.(Boiler)
OUT 3
OUT 2
OUT 1
SLmin
SLiv
+(Vcc)
Gnd
8X2
4
8X2
Drink keypad
PN.1264124
Main PCB
PN. 60100420
EvI.V.
EvA.I.
EvA.I.
EvC.C.
EvG.3
EvG.2
EvG.1
M
8X2
Display module
PN.2760062
5X2
~
F
N
COMMON
MAIN SUPLY
Electro valve
PN.60000120
Electro valve
PN.60000100
Electro valve
PN.60000105
Electro valve
PN.60000112
Electro valve
PN.60000112
+
-
+
C.C.R.
Air pump
Ref. 60100049
Ref. 60000049
OPTIONAL CAPUCINADOR WITH PERISTALTIC PUMP
-
+
M
Motor
PN.60000016
ELECTRICAL DIAGRAM
CARAT
Display board and IO-Board outputs 2Gr 230V 1+N
Water level sensor
PN.60100040
37
38
G
1660097
Contactor 230v
LC1D18P7C
L1
L2
L3
N
4
Power Switch
PN.1660036
T1
L1
1
3
T2
L2
2
A2
A1
PN.1660085
Capacitor 0.47uF(X3)
T3
L3
RESISTENCIA 4500W-230V 2GR
PN.C38045000
Thermal-link
2/T1
4/A2
4/A2
3/A1
1/L1
1/L1
4/A2
3/A1
2/T1
3/A1
1/L1
2/T1
Solid state relay
PN.C60800101
C10200150
Thermal Cut-out
3 Pole with bulb
Water level sensor
PN.60100040
8X2
Flow meter
PN.60100045
NTC steamer
Ref. 60100075
NTC Boiler
Ref. 60100076
Drink keypad
PN.1264124
S.T.C.(Boiler)
OUT 3
OUT 2
OUT 1
SLmin
SLiv
+(Vcc)
Gnd
8X2
4
8X2
Drink keypad
PN.1264124
Main PCB
PN. 60100420
EvI.V.
EvA.I.
EvA.I.
EvC.C.
EvG.3
EvG.2
EvG.1
M
8X2
Display module
PN.2760062
5X2
~
F
N
COMMON
MAIN SUPLY
Air pump
Ref. 60000049
-
+
M
Motor
PN.60000016
+
-
+
C.C.R.
Ref. 60100049
Electro valve
PN.60000120
Electro valve
PN.60000100
Electro valve
PN.60000105
Electro valve
PN.60000112
Electro valve
PN.60000112
ELECTRICAL DIAGRAM
CARAT
Display 2Gr TS Orchestra 400V 3+N
CARAT
ELECTRICAL DIAGRAM
Display 2Gr 3 boilers
L3
N
L2
L1
Power Switch
PN.1660036
4
1660097
Contactor 230v
LC1D18P7C
G
L1
T1
3
1
L2
T2
2
L3
T3
A1
A2
PN.1660085
Resistance 4500W-230V 2GR
PN.C38045000F
Thermal-link
Resistance
1200W-230V
PN.C38012000
Resistance
1200W-230V
PN.C38012000
Capacitor 0.47uF(X3)
t°
T.S.1
PN.C10200110
t°
T.S.1
PN.C10200110
C10200150
Thermal Cut-out
3 Pole with bulb
2/T1
1/L1
2/T1
4/A2
3/A1
4/A2
3/A1
4/A2
3/A1
3/A1
4/A2
2/T1
2/T1
3/A1
4/A2
2/T1
1/L1
1/L1
1/L1
Solid state relay
PN.C60800101
1/L1
NTC Boiler
PN.C60100076
NTC steamer
PN. C60100075
Flow meter
PN.60100045
8X2
Drink keypad
PN.1264124
Gnd
+(Vcc)
SLiv
OUT 1
SLmin
OUT 2
OUT 3
8X2
8X2
4
Main PCB
PN. 60100420
Drink keypad
PN.1264124
5X2
8X2
N
~
F
EvI.V.
EvA.I.
EvA.I.
EvC.C.
EvG.3
EvG.2
EvG.1
M
COMMON
MAIN SUPLY
Display module
PN.2760062
-
+
M
Motor
PN.60000016
Electro valve
PN.60000112
Electro valve
PN.60000112
Electro valve
PN.60000105
Electro valve
PN.60000100
+
-
-
+
C.C.R.
Ref. 60100049
Electro valve
PN.60000120
Air pump
Ref. 60000049
39
Water level sensor
PN.60100040
WATER SYSTEM
Machine with 1GR
Cold water
Hot water
Drain / waste water
40
CARAT
WATER SYSTEM
CARAT
Machine with 2GR
Cold water
Hot water
Drain / waste water
41
EXPLODED VIEW
CARAT
Machine with 1GR
Drawing
1 2
5
6
7 28 29
25
8
9
3 4
10
30
26
27
13
35
12
11
20
14
15
32
23
24
33
19
18
16 17
34
31
42
21
22
EXPLODED VIEW
CARAT
Machine with 1GR
Spare parts list
POS.
PCS
Part No.
Description
1
1
1264089
Left panel upper white
2
1
1264162
Left panel upper black
3
1
1264090
Left panel lower white
4
1
1264163
Left panel lower black
5
1
260712
Left Upper Panel Cover
6
1
1264096
Display overlay 1Gr TS
7
1
1264141
Display overlay 1Gr Standard
8
1
260688
Display Panel 1Gr Standard
9
1
260711
Display Panel Assy 1GR Carat
10
1
260718
Back Panel 1GR Carat
11
1
260715
Right Lower Panel Cover
12
1
260714
Right Upper Panel Cover
13
1
260713
Left Lower Panel Cover
14
1
260720
Group Cover Support Carat
15
1
260674
Cup Holder Carat
16
1
1264104
Front Brand Panel
17
1
1264167
Front brand panel 1Gr black
18
1
260716
Drip Tray 1GR Carat
19
1
260717
Grid Carat 1Gr
20
1
260710
Front Panel 1GR Carat
21
1
1264092
Right panel lower white
22
1
1264165
Right panel lower black
23
1
1264091
Right panel upper white
24
1
1264164
Right panel upper black
25
1
260719
Top Cup Tray 1GR Carat
26
1
260679
Strengthen Panel 1Gr
27
1
260677
Water Proof Top
28
1
1260005
Insulation Back Panel Carat 1Gr
29
1
1260015
Insulation Top Tray 1Gr
30
1
1264208
Back Overlay 1Gr
31
1
1264241
Water Proof Pan 1Gr
32
2
1264234
Plactic Strip
33
2
260676
Bearing
34
1
C10200141
Pole thermal cut-out with bulb
35
1
1608281
Magnet 39x13x6
43
EXPLODED VIEW
CARAT
Machine with 2GR
Drawing
11
1 2
7
8
6
12
9
10
5
30
35
18
3 4
34
31
29
16
26
17
20
28
27
32
13 14
19
15
33
25
21 22
44
23 24
EXPLODED VIEW
CARAT
Machine with 2GR
Spare parts list
POS.
PCS
Part No.
Description
1
1
1264089
Left panel upper white
2
1
1264162
Left panel upper black
3
1
1264090
Left panel lower white
4
1
1264163
Left panel lower black
5
1
260713
Left Lower Panel Cover
6
1
260712
Left Upper Panel Cover
7
1
1264116
Display overlay 2Gr TS
8
1
1264142
Display overlay 2Gr Standard
Display Panel 2Gr Standard
9
1
260689
10
1
260728
Display Panel Assy 2Gr Carat
11
1
260730
Top Cup Tray 2Gr Carat
12
1
260699
Back Panel 2Gr Carat
13
1
1264115
Front brand panel 2Gr white
14
1
1264166
Front brand panel 2Gr black
15
1
260731
Drip Tray 2Gr Carat
16
2
260674
Cup Holder Carat
17
1
260700
Grid Carat 2Gr
18
1
260729
Front Panel 2Gr Carat
19
1
260715
Right Lower Panel Cover
20
1
260714
Right Upper Panel Cover
21
1
1264091
Right panel upper white
22
1
1264164
Right panel upper black
23
1
1264092
Right panel lower white
24
1
1264165
Right panel lower black
25
1
1264242
Water Proof Pan 2Gr
26
1
260720
Group Cover Support
27
4
1264234
Plactic Strip
Bearing
28
4
260676
29
1
260677
Water Proof Top
30
1
1264209
Back Overlay 2Gr
31
1
1260011
Insulation Back Panel Carat 2Gr
32
1
1264261
EGO 3 Pole Cover
33
1
C10200150
3 Pole Thermal cut-out with bulb
34
1
260678
Strengthen Panel 2Gr
35
2
1608281
Magnet 39x13x6
45
EXPLODED VIEW
CARAT
Rotary pump
Drawing
8
1
9
7
10
4
11
2
3
5
6
46
EXPLODED VIEW
CARAT
Rotary pump
Spare parts list
POS.
PCS
Part No.
Description
1
1
C60000016
MOTOR CREM 230V/50HZ
2
8
C25093420
HEXAGONAL NUT M-6 DIN-934
3
4
C50100000
SILENTBLOCK M-6
4
1
C30000019
CARDAN JOINT PUMP
5
1
C60000031
Piston Bypass Pump (Tec)
6
1
C60000030
Pump(Crem Special Treatment)
7
1
C65000010
Retention Valve 3/8*1/8 (Min-Mon-Ec)
8
1
C30400055
Pump Bypass Condor
9
1
C30100100
Inlet Water Filter Holder
10
1
C70000009
Tubular Group Filter
11
1
C30000240
PUMP ADAPTOR 3/8 X 3/8
47
EXPLODED VIEW
CARAT
Boiler 1GR
Drawing
3
4
2
1
6
10
13
12
9
7
8
14
5
17
15
5
16
18
48
11
EXPLODED VIEW
CARAT
Boiler 1GR
Spare parts list
POS.
PCS
Part No.
Description
1
1
C60100040
Water Level Probe 1/4
2
1
C25000003
Inox Ground Washer
3
1
C30000200
Thermics Sup. Adaptor 1/2 X 1/2
4
1
CESC00100
Magnets Set
5
2
C50010010
21.1*25.7* 1/2 Teflon Gasket
6
2
C30000003
Reducer Male-Female-3/8 - 1/4
7
1
C60100076
Temp. Probe + Susp. Steam Pipe Icd
8
1
C65000200
Non Suction Valve
9
1
C65000100
3/8 Safety Valve
10
1
C30000110
3 Tracks Adaptor 1/4 * 1/4 * 1/8
11
3
C25093320
Hexagonal Head Screew 8X20 Din 933
12
3
C25012530
Flat Washer M-8 Din-125
13
1
C38025001F
2500W-230V- 6Ltrs.Copper Element with
fuses
14
1
C50010030
40*52*2 Element Teflon Gasket
15
1
C15100018
Boiler Copper 1Gr 6L
16
1
C30000210
Thermics Inf. Adaptor-1/2X1/2X1/4
17
1
1260003
Insulation Boiler Carat 1Gr
18
1
C30000220
Cone Injector 1/4
49
EXPLODED VIEW
CARAT
Boiler 2GR
Drawing
11 12 13 14
15
12
14
1
16
2
3
17
4
5
18
6
10
50
9
8
7
EXPLODED VIEW
CARAT
Boiler 2Gr
Spare parts list
POS.
PCS
Part No.
Description
1
1
C60100040
WATER LEVEL PROBE 1/4
2
1
C65000100
3/8 SAFETY VALVE
3
1
C30000100
2 TRACKS ADAPTOR- 1/4 x 1/8
4
1
C25000003
INOX GROUND WASHER
5
1
C25679812
M12 Washer
6
1
C15100020
BOILER 2GR 11LTS.
7
1
C50010030
40*52*2 ELEMENT TEFLON GASKET
8
1
C38027000F
3050W.230V- 2gr ELEMENT with fuses
9
3
C25012530
FLAT WASHER M-8 DIN-125
10
3
C25093320
HEXAGONAL HEAD SCREEW 8x20 DIN
933
11
1
C30000315
BLING PLUG 1/8 FEMALE
12
4
C50010010
21.1*25.7* 1/2 TEFLON GASKET
13
1
C65000200
NON SUCTION VALVE
14
2
C30000003
REDUCER MALE-FEMALE-3/8 - 1/4
15
2
C30000200
THERMICS SUP. ADAPTOR 1/2 X 1/2
16
1
C60100076
TEMP. PROBE + SUSP. STEAM PIPE ICD
17
1
C30000290
PLUG M 3/8
18
1
1260004
Insulation Boiler Carat 2Gr
51
EXPLODED VIEW
CARAT
2Gr 3 Boilers: boiler assembly (main boiler)
Drawing
01
02
03
04
05
06
07
08
09
10
11
12
21
20
19
18
17
16
15
52
14
13
EXPLODED VIEW
CARAT
2Gr 3 Boilers: boiler assembly (main boiler)
Spare parts list
i
POS.
PCS
Part No.
Description
01
1
C60100076
Temp. Probe + Susp. Steam Pipe Icd
02
1
C30000003
Reducer Male-Female-3/8 - 1/4
03
1
C30000290
Plug M 3/8
04
1
C65000200
Non Suction Valve
05
2
C30000315
Bling Plug 1/8 Female
06
2
C30000510
Conical Adaptor 1/4*1/4 Electron
07
2
C30000220
Cone Injector 1/4
08
2
C50010020
13.2*18.2*2.5 1/4 Teflon Gasket
09
2
C30000210
Thermics Inf. Adaptor-1/2X1/2X1/4
10
1
C65000110
Cn10 Ptfe Ce Safety Valve
11
2
C50010010
21.1*25.7* 1/2 Teflon Gasket
12
1
C30000100
2 Tracks Adaptor- 1/4 X 1/8
13
1
C38027000F
3050W.230V- 2Gr Element with fuses
*13
1
C38045000F
4500W-230V 2GR Element with fuses
14
1
C50010030
40*52*2 Element Teflon Gasket
15
1
C15100020
Boiler 2Gr 11Lts.
*15
1
C15100030
Boiler 3Gr 17Lts.
16
2
C30200035
Long Plug 1/2 Group
17
1
C25679812
M12 Washer Form A
18
1
C25000003
Inox Ground Washer
19
1
C60100040
Water Level Probe 1/4
20
1
C30000110
3 Tracks Adaptor 1/4 * 1/4 * 1/8
21
2
C50010050
3/8 Boiler's Connector Teflon Gaske
Note:
Parts 13 marked with * are options on three-phase models.
53
EXPLODED VIEW
CARAT
2Gr 3 Boilers: boiler assembly (group boiler)
Drawing
01
11
02
10
03
09
04
05
08
12
06
07
Spare parts list
54
POS.
PCS
01
1
C30000220
Part No.
Cone Injector 1/4
Description
02
1
C50010020
13.2*18.2*2.5 1/4 Teflon Gasket
03
2
C25091210
Allen Screw 4X12 Din-912
04
1
C10200110
Office Thermostat 16 A
05
1
C30000290
Plug M 3/8
06
1
C38012000
1200W-230V Office Element
07
2
C30000300
Blind Plug 1/4 Male
08
1
C15100010
Office Cappuccinator Boiler
09
1
C60100076
Temp. Probe + Susp. Steam Pipe Icd
10
2
C50010010
21.1*25.7* 1/2 Teflon Gasket
11
2
C30000200
Thermics Sup. Adaptor 1/2 X 1/2
12
1
1260017
Insulation Boiler Office
EXPLODED VIEW
CARAT
Turbo steamer
Drawing
6
5
4
1
8
12
3
7
2
9
10
19
11
14
13
20
21
18
16
17
15
55
EXPLODED VIEW
CARAT
Turbo steamer
Spare parts list
POS.
PCS
1
1
C30000510
Conical Adaptor 1/4*1/4 Electron
2
1
C30700000
6Mm Barbfitting 1/8 F
3
1
C60000120
Valve Turbo Steamer
4
1
C50010050
3/8 Boiler's Connector Teflon Gaske
5
1
C25012510
Washer M-5 Din9021
6
1
C25091200
Allen Screw 4X8 Din-912
7
1
C30000235
Male Adapter 1/4*3/8*M-5 Water
8
1
C60100075
Steam Temperature Sensor
9
1
C50010080
Gasket Tap Steam/Water Teflon
10
1
C30370076
Spring Steam/Water Tap
11
1
C30370077
Gasket Tap Steam/Water Brass
12
1
C30500005
Male Hose Adapter Elow
13
1
C30370075
O-Ring For Steam Tap
14
0.35m
C35021000
Silicon Hose DIA4*7mm
15
1
C30370190
Nozzle steam tap-1H M8.5 with oring
16
1
C50010090
O-Ring 6X1
17
1
C30370195
Nozzle Steam Tap 3H M8.5 with Gasket
18
1
C2760028
Steam Tap Assembly Carat
19
1
C60000049
Peristaltic Pump
20
1
C20010006
Peristaltic Pump Support
21
1
C60100049
Adjustable Unit Trimmer
56
Part No.
Description
EXPLODED VIEW
CARAT
Steam wand
Drawing
13
18
14
12
11
10
9
6
7
8
5
3
15
16
1
17
2
19
20
21
4
57
EXPLODED VIEW
CARAT
Steam wand
Spare parts list
POS.
PCS
1
1
1264215
Steam Tap Lever Espresso Filter
2
1
C30370095
Pipe steam Eleg./MegaCrem wo nozzle
3
1
C21003041
Tap Cover
4
1
C30370190
Nozzle steam tap-1H M8.5 with oring
5
1
C30370141
Nut G5/8 * H26
6
1
C30370161
Tap axle with nob
7
1
C30370165
Conector FemaleG1/2-Male G5/8
8
1
C30370164
Holder washer
9
1
C15000338
Tap Body and Steam Knob
10
1
C50000133
O-ring (10.77x2.62)
11
1
C30370163
Extension axle for tap
12
1
C55000070
Spring, 14X24x1,5-OA2
13
1
C30370166
Connector 3/4M x G14M
14
1
C50010070
Teflon gasket (19X24x2)
15
1
C50010080
Gasket Tap Steam/Water Teflon
16
1
C30370076
Spring Steam/Water Tap
17
2
C30370077
Gasket Tap Steam/Water Brass
18
1
C50000100
O-Ring 6.07x1.78
19
2
C30370075
O-Ring for Steam Tap
20
1
C50010090
O-ring 6X1
21
1
C30370195
Nozzle Steam Tap 3H M8.5 with Gasket
58
Part No.
Description
EXPLODED VIEW
CARAT
Hot water outlet
Drawing
1
2
4
3
5
6
7
8
9
10
11
12
59
EXPLODED VIEW
CARAT
Hot water outlet
Spare parts list
POS.
PCS
Part No.
1
1
C30000510
Conical Adaptor 1/4*1/4 Electron
2
1
C60000100
1/4 X 1/4 Electrovalve Parker 220V
3
1
C30100010
Hexagonal Nut 1/4 Pressostat
4
1
C30000236
Elbow Racor G1/4Xg3/8
5
1
C50010080
Gasket Tap Steam/Water Teflon
6
1
C30370076
Spring Steam/Water Tap
7
1
C30370077
Gasket Tap Steam/Water Brass
8
1
C30370075
O-Ring 12.1X2.7mm
9
1
C70000010
Nut 3/8 For Steamer
10
-
C30000050
Nozzle Water Tap Complete
11
-
C30370080
Water Tap Classic
12
1
C30370081
Water Tap + Connector Kit
60
Description
EXPLODED VIEW
CARAT
Group head
Drawing
1
2
3
4
5
6
13
14
7
15
8
16
10
9
12
11
61
EXPLODED VIEW
CARAT
Group head
Spare parts list
POS.
PCS
1
1
C30200035
Long Plug 1/2 Group
2
1
C50010040
21.7*25.7*2 G/C-G Teflon Gasket
3
1
C70000009
Tubular Group Filter
4
1
C30200061
Group Teflon Injector Rev3
5
1
C30200026
Tefl Water Reduc. Holder 4X6x65
6
1
C25091250
Allen Screw 6*10 Din-912 Group
7
1
C30200010
Crem Brewing Group Body
8
1
C30200040
Diffuser
9
1
C75000010
Shower
10
1
C60000112
Gro Head Electrov. Parker 220V
11
1
C30700000
6Mm Barbfitting 1/8F
12
1
C75000081
8Mm Group Head Gasket
13
1
C50020020
2.5*18.2*2 Teflon Hot Water Reducto
14
1
C50000010
Green Body Flat Group Joint
15
1
C50000100
O-Ring 6.07*1.78
16
4
C25091211
Allen Screw M4x16 Din 912
62
Part No.
Description
EXPLODED VIEW
CARAT
Lower water system
Drawing
1
6
7
2
8
9
10
3
11
4
12
13
5
63
EXPLODED VIEW
CARAT
Lower water system
Spare parts list
POS.
PCS
1
1
C30000002
BUTTRESS 1/4-3/8 MINI
2
1
C30100010
HEXAGONAL NUT 1/4 PRESSOSTAT
3
1
C30100033
DISTRIBUTOR MC
4
1
1364029
Distributor Tube ø8mm Carat 2Gr
4
1
1364021
Copper Tube Φ8.0*100mm 1Gr
5
2
C60100045
FLOWMETER UL/NETW. BRASS TEF+LED
6
1
C60000105
50/60HZ 220V SOLENOID ELECTROVALVE
7
2
C25091210
ALLEN SCREW 4x12 DIN-912
8
1
C50000110
SMALL AUTOFILL SOLENOID GASKET
9
1
C50000105
LARGE AUTOFILL SOLENOID GASKET
10
1
C30100010
HEXAGONAL NUT 1/4 PRESSOSTAT
11
1
C30000215
CONICAL BEND ADAPTOR 1/4 X 1/4
12
1
C30100010
HEXAGONAL NUT 1/4 PRESSOSTAT
13
2
1860016
Tap drainage G1/4M-G1/4F Right
64
Part No.
Description
EXPLODED VIEW
CARAT
Porta-filter
Drawing
6
1
7
4
2
2
3
5
Spare parts list
POS.
PCS
Part No.
Description
1
1
C75000031
1 Cup Filter (7Gr)
2
2
C75000120
Filter Spring
3
1
C75000050
Spout 1Cup
4
1
C75000041
2 Cup Filter (14Gr)
5
1
C75000060
Spout 2Cups
6
1
2760126
Filter Handle Assy 1 Cup
7
1
2760127
Filter Handle Assy 2 Cup
65
EXPLODED VIEW
CARAT
Machine components
DRAWING
PART NO.
C60100420
Main control box
C60100049
Adjustable Unit Trimmer
C60000072
Manometro D40 0_16 BAR
C60000062
Manometro D40 0_2.5 BAR
C60100045
Flowmeter UL Red TEF Led
1660097
66
MODEL/NAME
Contactor 230V LC1D18P7C
EXPLODED VIEW
CARAT
Machine components
DRAWING
PART NO.
1660036
MODEL/NAME
Power Switch Blue Φ22mm
C60800103
Solid State Relay Cover
C60800101
STATIC RELAY 4-32
C70001001
C70001005
Drain cup with thread
Drain cup cover
260177
DIN Connection SS 65MM
67
EXPLODED VIEW
CARAT
Machine components
DRAWING
68
PART NO.
MODEL/NAME
1660131
Peristaltic Pump with Harness
1666032
Harness NTC Extension
1666039
Signal cable
1666061
Long Cable Signal Carat
C16660028
Harness complete Carat 1Gr
C16660029
Harness complete Carat 2Gr
1666042
Harness complete Carat 2Gr 3phase
C60102020
O-ring flowmeter
EXPLODED VIEW
CARAT
Machine components
Drawing
1
8
7
14
13
12
6
5
4
3
2
9
10
11
Spare parts list
POS.
PCS
Part No.
Description
1
1
2760062
Display PCB Assy with 2 Buttons
2
1
C*60101513
Metal button set cover water/steam
3
1
1264156
Conductive Control Button 2 Keys
4
1
1660040
PCB Mechanical Type 2 Buttons
5
1
C60101060
Graphic Display Gicar
6
1
1264128
Display PCB Box Bottom 2 Buttons
7
1
1264129
Display PCB Box Upper 2 Buttons
8
1
2760031
Display PCB Assembly Carat
9
1
C*60101512
METAL BUTTON SET COVER (x5)
10
1
1264107
Display PCB Box Upper Carat
11
1
1264108
Display PCB Box Bottom Carat
12
1
1264095
Conductive Control Button
13
1
C60101060
Graphic Display Gicar
14
1
1660039
PCB Mechanical Type 5 Buttons
69
EXPLODED VIEW
CARAT
Machine components
Drawing
1
2
3
4
5
6
Spare parts list
POS.
PCS
1
1
1264124
Button Box Assy Carat
2
1
C*60101512
METAL BUTTON SET COVER (x5)
3
1
1264126
Button Box Upper
4
1
1264095
Conductive Control Button
5
1
1264125
Button Box Bottom
6
1
1660039
PCB Mechanical Type 5 Buttons
70
Part No.
Description
For the warranty to be valid the conditions for maintenance must have been
followed according to our instructions, proper precaution has been made and
warranty claim been issued without delay.
The affected equipment may not be used during awaiting service if there is any risk
that the damage or defect would worsen.
The warranty will not cover consumption supplies such as glassware, normal
maintenance such as cleaning of filters, contaminations in water, lime, incorrect
voltages, pressure or adjustment of water amounts.
The warranty will not cover damages of defects caused by incorrect handling and
operation of the appliance.
FOR SERVICE
Please contact your dealer
Your Dealer
Models coverd by this manual:
EAED-C32B-22AM
EBED-C32B-22AM
EBEE-D32B-22AM
EAED-C41B-22AM
EAED-C41B-22AM
EBEE-D41B-22AM
EBAE-D41B-22AM
EBGE-G41B-22AM
www.creminternational.com