Model No.
Serial No.
The model number and serial number are found in the location shown
below. Write the model number and
serial number in the space above.
Serial
Number
Decal
QUESTIONS?
At FreeMotion Fitness, we’re
committed to providing complete
customer satisfaction. If you
have questions, see HOW TO
CONTACT CUSTOMER CARE on
page 2 of this manual.
CAUTION
Read all precautions and instructions in this manual before
using this equipment. Keep this
manual for future reference.
USER'S MANUAL
TABLE OF CONTENTS
SECTION 1
How to Contact Customer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
How to Assemble the Elliptical Trainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
How to Set Up the Elliptical Trainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
SECTION 2
SECTION 3
SECTION 4
SECTION 5
How to Upgrade the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
How to Use the Basic Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Exercise Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Exploded Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
NordicTrack is a registered trademark of ICON IP, Inc.
1
HOW TO CONTACT CUSTOMER CARE
If you have questions after reading this manual, or if you require assistance, please contact Customer Care at the
address and phone number listed below. Please be prepared to give the following information:
• The MODEL NUMBER OF THE PRODUCT (see the front cover of this manual for the location)
• The NAME OF THE PRODUCT (NordicTrack® 9600E elliptical trainer)
• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual for the location)
When ordering replacement parts, please also give the KEY NUMBER and DESCRIPTION OF THE PART(S)
(see the PART LIST and the EXPLODED DRAWING on pages 27 to 31)
Customer Care: 1-800-201-2109, Monday–Friday, 8 a.m.–5 p.m. Mountain Time
FreeMotion Fitness, Inc. • 1096 Elkton Drive, Suite 600 • Colorado Springs, CO 80907
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
and information before operating the elliptical trainer.
1. It is the responsibility of the owner to ensure
that all users of the elliptical trainer are adequately informed of all warnings and precautions.
9. Always wear appropriate exercise clothes and
athletic shoes when operating the elliptical
trainer. Do not wear loose clothes that could
become caught on the elliptical trainer.
2. Operate the elliptical trainer only as described
in this manual.
10. Do not modify the power cord or use an adaptor to connect the power cord to an improper
receptical (see HOW TO CONNECT THE
POWER CORD on page 7). Keep the power
cord away from heated surfaces. Do not use
an extension cord.
3. Do not operate the elliptical trainer until it is
properly assembled (see HOW TO ASSEMBLE
THE ELLIPTICAL TRAINER on page 5).
4. Keep the elliptical trainer indoors, away from
moisture and dust. Do not place the elliptical
trainer in a garage or covered patio or near
water.
11. Keep your back straight when using the elliptical trainer; do not arch your back.
12. If you feel pain or dizziness whilst exercising,
stop immediately and cool down.
5. Place the elliptical trainer on a level surface.
To protect the floor or carpet from damage,
place a mat beneath the elliptical trainer.
13. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
6. Regularly inspect and tighten all parts of the
elliptical trainer.
7. Keep children under the age of 12 and pets
away from the elliptical trainer at all times.
14. The battery pack contains materials that are
considered hazardous to the environment.
Proper disposal of the battery is required by
federal law. See HOW TO REPLACE THE BATTERY PACK on page 22.
8. The elliptical trainer should not be used by
persons weighing more than 158 kg (350 lbs).
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
3
BEFORE YOU BEGIN
Congratulations for selecting the revolutionary NordicTrack® 9600E elliptical trainer. The NordicTrack 9600E
elliptical trainer offers an impressive array of features
to make your workouts more effective and enjoyable.
To help us assist you, please note your product model
number and serial number before calling. The model
number and serial number can be found on a decal attached to the elliptical trainer (see the front cover of
this manual for the location of the decal).
For your benefit, read this manual carefully before
using the NordicTrack 9600E elliptical trainer. If
you have questions after reading this manual, see
HOW TO CONTACT CUSTOMER CARE on page 2.
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
Console
Book Rack
FRONT
Handgrip Pulse Sensor
Handlebar
CD/Accessory Tray
Water Bottle Holder*
Wheel
Levelling Foot
RIGHT SIDE
Pedal Cover
REAR
*No water bottle is included
4
HOW TO ASSEMBLE THE ELLIPTICAL TRAINER
Assembly requires two persons. Set the elliptical trainer in a cleared area and remove all packing materials. Do
not dispose of the packing materials until assembly is completed. Assembly can be completed using the included hex keys.
1. Lift the Left Handlebar Arm (17) to the position
shown. Attach the Left Handlebar Arm to the Left
Handlebar (19) with two 3/8” x 5/8” Shoulder
Screws (100).
1
20
19
Attach the Right Handlebar Arm (not shown) to the
Right Handlebar (20) in the same way.
100
17
2. Have another person hold the Upright (2) in the position shown. Connect the Lower Power Wire (96)
to the Upper Power Wire (97). Connect the Lower
CATV Cable (102) to the Upper CATV Cable (101).
Connect the Lower Battery Wire (77) to the Upper
Battery Wire (78). Connect the Lower Controller
Wire (80) to the Upper Controller Wire (79).
2
48
Attach the Upright (2) to the Frame (1) with four
3/8” x 1 1/4” Button Head Screws (48) and four 3/8”
Star Washers (85). Make sure that no wires are
pinched between the Upright and the Frame.
85
97
96
101
2
78
79
77
102
5
80
85
1
48
48
85
3. Attach the Upright Cover (29) to the Upright (2) with
three #8 x 1/2” Button Head Screws (92). Attach
the Water Bottle Holder (26) to the Frame (1) with
four #8 x 1/2” Button Head Screws (92).
3
29
2
92
6
26
1
92
HOW TO SET UP THE ELLIPTICAL TRAINER
HOW TO MOVE AND LEVEL THE ELLIPTICAL
TRAINER
Before moving the elliptical trainer, make sure
that the power cord is unplugged. Note: If a CATV
cable is connected to the elliptical trainer, it may be
necessary to disconnect the cable if the elliptical
trainer will be moved far.
Lift
Here
Due to the size and weight of the elliptical trainer,
moving it requires two persons. Have two persons
lift the indicated end and tip the elliptical trainer forward until it rolls on the front wheels. Carefully move
the elliptical trainer to the desired location and then
lower it back to the level position. CAUTION: To decrease the risk of injury, bend your legs and keep
your back straight. As you raise the elliptical
trainer, make sure to lift with your legs rather
than your back. Do not attempt to move the elliptical trainer over uneven surfaces.
Wheels
If the elliptical trainer rocks slightly during use, turn
the levelling feet under the front of the frame until the
rocking motion is eliminated.
Levelling
Feet
HOW TO CONNECT THE POWER CORD
If the elliptical trainer has a Basic console, it can be used with or
without a power cord. To purchase a power cord, see HOW TO
CONTACT CUSTOMER CARE on page 2 of this manual. If the elliptical trainer has a Workout TV console, a power cord must be
used for the TV to be operated. A power cord is included with the
Workout TV console.
To use a power cord, first plug one end of the power cord into the
jack on the front of the elliptical trainer. Plug the other end of the
power cord into an appropriate outlet that is properly installed in accordance with all local codes and ordinances.
Power
Cord
Jack
HOW TO CONNECT A CATV CABLE
If your elliptical trainer has a Workout TV console, a CATV cable
must be connected to the elliptical trainer for cable TV stations to
be viewed. Locate the cable jack on the front of the elliptical trainer.
Connect the CATV cable to the cable jack.
Cable
A satellite receiver, VCR, or DVD player can also be connected to
Jack
the elliptical trainer. Connect a CATV cable from the coaxial output
on your equipment (usually labelled TV OUT or RF OUT) to the cable
jack. Note: Audio/video equipment without coaxial outputs (some
satellite receivers and DVD players) will require an RF modulator to
operate with the elliptical trainer. RF modulators and external CATV cables are not available from FreeMotion
Fitness, but are available at electronics stores. See the owner's manual included with the equipment you wish to
connect to see whether an RF modulator is needed.
7
HOW TO UPGRADE THE CONSOLE
Your elliptical trainer has been pre-configured to operate with a Basic console and a Workout TV console (see
the drawings below). To learn about the features of the Basic console, see page 9. To learn about the features of
the Workout TV console, see the user’s manual included with the Workout TV console.
To upgrade your console and expand the capabilities of your elliptical trainer whenever you choose, see
HOW TO CONTACT CUSTOMER CARE on page 2 of this manual.
Basic
Console
Workout TV
Console
F
8
S
A
HOW TO USE THE BASIC CONSOLE
Matrix
Main Display
FEATURES OF THE CONSOLE
the pedals to keep your heart rate near a target level
during your workouts. Note: The PULSE programs require the use of a Polar®-compatible chest pulse sensor
(not included).
The Basic console offers an impressive array of
features designed to help you get the greatest benefits
from your exercise on the elliptical trainer. When the
QUICK START mode is selected, the resistance of the
pedals can be changed with the touch of a button. As
you exercise, the console will provide continuous exercise feedback. You can even measure your heart rate
using the built-in pulse sensor.
Before using the elliptical trainer, please read
OVERVIEW OF THE CONSOLE on pages 10 to 12.
To use the QUICK START mode of the console,
follow the steps beginning on page 13. To use the
MANUAL program, see page 13. To use the RANDOM program, see page 15. To use a PULSE program, see page 16. To use the INTERVAL program,
see page 17. To use the PLATEAU program, see
page 18. To use the FOOTHILLS, PEAKS, or ALLTERRAIN program, see page 19. To use the maintenance mode, see page 20.
In addition, the console offers a wide selection of workout programs. Each program automatically controls the
resistance of the pedals as it guides you through an effective workout. The console also offers two PULSE
programs that automatically adjust the resistance of
9
THE BUTTONS
OVERVIEW OF THE CONSOLE
The CLEAR button—This
button is used to reset the
console. When this button is
pressed, the main display will
be reset and the words
“PLEASE SELECT A PROGRAM TO BEGIN” will scroll across the main display.
Note: If one program is started and then a different
program is selected, the main display will not be reset
unless the CLEAR button is pressed before the second
program is selected.
For your benefit, please read all of the instructions
on pages 10 to 12 before you use the elliptical
trainer.
HOW TO ACTIVATE THE CONSOLE
If the elliptical trainer has a Basic console, it can be
used with or without a power cord. To purchase and
use a power cord, see HOW TO CONNECT THE
POWER CORD on page 7. To use the elliptical trainer
without a power cord, simply begin pedalling at a cadence of about 25 revolutions per minute (RPM) or
faster. The main display will light, the indicators on the
QUICKTOUCH PROGRAMS buttons will begin to
flash, a tone will sound, and the words “PLEASE SELECT A PROGRAM TO BEGIN” will scroll across the
main display. Whilst you pedal, power will be supplied
by a generator; remember to continue pedalling whilst
using the elliptical trainer.
The QUICKTOUCH RESISTANCE buttons—These
buttons control the resistance of the pedals. There are
twenty resistance settings, from 0.5 to 10. Each time
the + or – button is pressed, the resistance setting will
change by 0.5. When one of the buttons numbered 1
to 10 is pressed, the corresponding resistance setting
will be selected. Note: It may take a moment for the
pedals to reach the selected resistance setting.
If the elliptical trainer has a Workout TV console,
the power cord must be used for the TV to be operated. See HOW TO CONNECT THE POWER CORD
on page 7. When the power cord is plugged in, the
main display will light, the indicators on the QUICKTOUCH PROGRAMS buttons will begin to flash, a
tone will sound, and the words “PLEASE SELECT A
PROGRAM TO BEGIN” will scroll across the main display.
The QUICKTOUCH PROGRAMS buttons—These
buttons are used to select the QUICK START mode
and the programs.
HOW TO TURN OFF THE CONSOLE
If the power cord is not being used, and if the pedals are not moved for a short period of time, the console will automatically turn off.
If the power cord is being used, and if the pedals are
not moved for a short period of time, the words
“PLEASE SELECT A PROGRAM TO BEGIN” will
scroll across the main display. Unplug the power cord
when the elliptical trainer is not in use.
The ENTER button and +
and – buttons—These buttons are used to enter information into the console.
10
THE MAIN DISPLAY
Speed/RPM—The right end
of the main display will show
your pedalling speed, in
miles per hour or kilometres
per hour, and your pedalling
cadence, in revolutions per
minute (RPM). The display will change from one number to the other every few seconds.
The main display will display a variety of text messages
to guide you through your workouts. In addition, the
main display will display the following information
whilst you exercise:
Resistance—The left end of
the main display will show
the resistance setting of the
pedals.
Note: The main display can display text messages in
any of six languages (see step 6 on page 20). In addition, the main display can display data using either the
English system or the metric system (see step 7 on
page 20).
Pace/Time/Segment
Time—When the QUICK
START mode is selected,
this section of the main display will show your pedalling
pace, in minutes per mile or
minutes per kilometre, and the elapsed time. The display will change from one number to the other every
few seconds. When a program is selected, the main
display will show your pedalling pace, the time remaining in the program, and the time remaining in the current segment of the program.
THE MATRIX
When the RANDOM, INTERVAL, PLATEAU, FOOTHILLS, PEAKS, or ALL-TERRAIN program is selected,
the matrix will display a profile of resistance settings.
Each program is divided into 30-second segments,
and each column of the matrix represents one 30-second segment. The flashing column represents the current segment. Note: If a program has more than 30
segments, the matrix will show up to 30 segments at a
time.
Distance—This section of
the main display will show
the distance that you have
pedalled, in miles or kilometres.
Flashing Column
Calories/Watts—This section of the main display will
show the approximate number of calories you have
burned and your power output in watts. The display will
change from one number to the other every few seconds.
The lit indicators in each column represent the resistance setting for that segment of the program. One lit
indicator represents a resistance setting of 0.5 or 1, two
lit indicators represent a resistance setting of 1.5 or 2,
three lit indicators represent a resistance setting of 2.5
or 3, and so forth. Note: Because there are eight indicators in each column, the matrix will normally show resistance settings up to 8. If resistance settings of 8.5, 9,
9.5, or 10 are programmed for one or more segments,
the lit indicators in all columns will occasionally shift
downward so that the higher settings higher are displayed in the matrix.
Heart Rate/% Max—When
you use the handgrip pulse
sensor or a Polar®-compatible chest pulse sensor (not
included), this section of the
main display will show your
heart rate. When a PULSE program is selected, the
display will show your heart rate and the corresponding percentage of your estimated maximum heart rate
(see step 6 on page 16 for an explanation of your estimated maximum heart rate). The display will change
from one number to the other every few seconds.
11
When the QUICK START mode or the MANUAL program is selected, the matrix will show the resistance
settings that you select.
Flashing Column
When a PULSE program is selected, the matrix will display a heartbeat graphic. Each time a heartbeat is detected, an additional peak will appear in the display.
THE PULSE SENSOR
If there are thin sheets
of plastic on the metal
contacts on the pulse
sensor, peel off the
plastic. To measure
Contacts
your heart rate, hold the
contacts; your palms
must be resting on the
upper contacts, and
your fingers must be touching the lower contacts.
Avoid moving your hands. When your pulse is detected, the HEART RATE indicator above the main display will begin to flash, and then your heart rate will be
shown. For the most accurate heart rate reading, hold
the contacts for at least 15 seconds without moving
your hands.
If your heart rate is not shown, make sure that your
hands are positioned as described. Be careful not to
move your hands excessively or to squeeze the contacts too tightly. For optimal performance, clean the
contacts using a soft cloth; never use alcohol, abrasives, or chemicals.
12
HOW TO USE THE QUICK START MODE
If you do not plan to use a program, the QUICK
START mode will allow you to simply start exercising
and adjust the resistance of the pedals manually.
1
2
3
Plug in the power cord or begin pedalling to
activate the console.
4
See HOW TO ACTIVATE THE CONSOLE on
page 10.
5
Select the QUICK START mode.
To select the QUICK START mode, press the
QUICK START button. The indicator on the button will light.
6
Begin exercising and change the resistance of
the pedals as desired.
After every 30 seconds that you exercise, a tone
will sound and the next column to the right will
begin to flash. When you have exercised for 8
minutes, the same column will continue to flash,
and all columns of indicators will shift one position
to the left. The columns of indicators will continue
to shift to the left after every 30 seconds, until you
are finished exercising.
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
Measure your heart rate if desired.
See THE PULSE SENSOR on page 12.
When you are finished using the elliptical
trainer, the console will automatically enter an
idle mode or turn off.
See HOW TO TURN OFF THE CONSOLE on
page 10.
As you pedal, change the resistance of the pedals
by pressing the RESISTANCE + and – buttons or
the QUICKTOUCH RESISTANCE buttons.
When the QUICK START mode is selected, the
matrix will show your progress and the resistance
settings that you select. When you begin exercising, the left column of the matrix will begin to flash.
After 30 seconds, a tone will sound and the column to the right will begin to flash.
HOW TO USE THE MANUAL PROGRAM
The MANUAL program will count down the time
remaining in your workout as you control the
resistance of the pedals.
Flashing Column
Each time you change the resistance of the pedals, additional indicators will light or darken in the
flashing column, and in all columns to the right of
the flashing column. Note: If you select a resistance setting higher than 8, the indicators in all
columns will shift downward, until you select a
lower resistance setting.
13
1
Plug in the power cord or begin pedalling to
activate the console.
2
Select the MANUAL program.
See HOW TO ACTIVATE THE CONSOLE on
page 10.
To select the MANUAL program, press the MANUAL button. The indicator on the button will light,
and the word “MANUAL” will appear in the main
display for a moment.
3
4
5
6
segment of the program, the left column of the matrix will flash. During the last four seconds of the
first segment, the column to the right will also
flash. When the first segment ends, a tone will
sound and the column to the right will continue to
flash.
Enter your age.
A moment after the program is selected, the
words “ENTER AGE” and an age setting of 35 will
appear in the main display. To enter your age,
press the + and – buttons beside the ENTER button; hold down the buttons to enter your age in increments of 5 years. When your age is shown,
press the ENTER button.
Each time you change the resistance of the pedals, additional indicators will light or darken in the
flashing column, and in all columns to the right of
the flashing column. Note: If you select a resistance setting higher than 8, the indicators in all
columns will shift downward, until you select a
lower resistance setting.
Enter your weight.
Next, the words “ENTER WEIGHT” and a weight
setting of 180 pounds will appear in the main display. To enter your weight, press the + and – buttons beside the ENTER button; hold down the
buttons to enter your weight in increments of 5
pounds. When your weight is shown, press the
ENTER button.
Enter a program time.
Next, the words “ENTER TIME” and a time setting
of 10 minutes will appear in the main display. To
change the length of time that the program will
last, press the + and – buttons beside the ENTER
button. Then, press the ENTER button.
7
Begin exercising and change the resistance of
the pedals as desired.
As you pedal, change the resistance of the pedals
by pressing the RESISTANCE + and – buttons or
the QUICKTOUCH RESISTANCE buttons.
During the MANUAL program, the
matrix will show
your progress and
the resistance settings that you select. During the
first 30-second
8
9
Flashing Column
At the end of each segment, a tone will sound and
the next column to the right will begin to flash.
When you have completed the first 8 minutes of
the program, the same column will continue to
flash, and all columns of indicators will shift one
position to the left. The columns of indicators will
continue to shift to the left at the end of each segment, until the last segment of the program is
shown in the far right column of the matrix. The
next column to the right will then begin to flash at
the end of each segment, until the program is
completed.
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
Measure your heart rate if desired.
See THE PULSE SENSOR on page 12.
When you are finished using the elliptical
trainer, the console will automatically enter an
idle mode or turn off.
See HOW TO TURN OFF THE CONSOLE on
page 10.
14
segment. Note: The same resistance setting may
be programmed for two or more consecutive segments.
HOW TO USE THE RANDOM PROGRAM
The RANDOM program will automatically change the
resistance of the pedals during your workout. Each
time the program is selected, the resistance settings of
the program will be different.
1
Plug in the power cord or begin pedalling to
activate the console.
2
Select the RANDOM program.
3
4
5
6
7
During the proFlashing Column
gram, the matrix
will show your
progress and the
resistance settings
of the program.
During the first 30second segment of
the program, the
left column of the matrix will flash. During the last
four seconds of the first segment, the column to
the right will also flash. If the resistance of the pedals is about to change, a series of tones will sound
and the resistance setting will flash in the main display. When the first segment ends, the column to
the right will continue to flash, and the resistance
of the pedals will automatically change if a different resistance setting is programmed for the next
segment. Note: If all of the indicators in the flashing column are lit, the indicators in all columns
may shift downward temporarily.
See HOW TO ACTIVATE THE CONSOLE on
page 10.
To select the RANDOM program, press the RANDOM button. The indicator on the button will light,
and the word “RANDOM” will appear in the main
display for a moment. Note: To select a different
RANDOM program, simply press the RANDOM
button again.
Enter your age.
See step 3 on page 14.
At the end of each segment, a tone will sound, the
next column to the right will begin to flash, and the
resistance of the pedals will automatically change
if a different resistance setting is programmed for
the next segment. When you have completed the
first 8 minutes of the program, the same column
will continue to flash, and all columns of indicators
will shift one position to the left. The columns of indicators will continue to shift to the left at the end
of each segment, until the last segment of the program is shown in the far right column of the matrix.
The next column to the right will then begin to flash
at the end of each segment, until the program is
completed.
Enter your weight.
See step 4 on page 14.
Enter a program time.
See step 5 on page 14.
Enter a maximum resistance setting.
Next, the words “MAX RESIST” and the maximum
resistance setting of the program will appear in
the main display. If you wish to change the maximum resistance setting, press the + and – buttons
beside the ENTER button. (Note: If the maximum
resistance setting is increased, the intensity level
of the program will be increased.) When the desired maximum resistance setting is shown, press
the ENTER button.
During the program, you can change the resistance of the pedals, if desired, by pressing the
RESISTANCE + and – buttons or the QUICKTOUCH RESISTANCE buttons. However, when
the current segment ends, the resistance will automatically change if a different resistance setting
is programmed for the next segment. Note: The
program ends with a two-minute cool-down period.
During this period, the resistance level cannot be
changed.
Begin exercising.
The program is divided into 30-second segments.
One resistance setting is programmed for each
15
8
9
10
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
Measure your heart rate if desired.
See THE PULSE SENSOR on page 12.
When you are finished using the elliptical
trainer, the console will automatically enter
an idle mode or turn off.
4
See HOW TO TURN OFF THE CONSOLE on
page 10.
HOW TO USE THE PULSE PROGRAMS
5
6
HOW TO USE THE PULSE PROGRAMS
The CONSTANT PULSE program will automatically
control the resistance of the pedals to keep your heart
rate near a target level during your workout.
The VARIABLE PULSE program will automatically
control the resistance of the pedals to keep your heart
rate within a target range during your workout.
1
Put on a Polar®-compatible chest pulse sensor
(not included).
2
Plug in the power cord or begin pedalling to
activate the console.
3
Select one of the PULSE programs.
You must wear a chest pulse sensor to use a
PULSE program. See the instructions included
with the chest pulse sensor.
7
8
See HOW TO ACTIVATE THE CONSOLE on
page 10.
To select a PULSE program, first press the
PULSE button. The indicator on the button will
light, and the word “PULSE” will appear in the main
display for a moment.
16
Next, the words “CONSTANT MODE” will appear
in the main display. If you plan to use the CONSTANT PULSE program, press the ENTER button. If you plan to use the VARIABLE PULSE program, press the + or – button beside the ENTER
button so that the words “VARIABLE MODE” appear in the main display; then press the ENTER
button.
Enter your age.
See step 3 on page 14.
Enter your weight.
See step 4 on page 14.
Enter a maximum heart rate setting.
Next, the words “PCT MAX RATE” and the maximum heart rate setting of the program will appear
in the main display. The maximum heart rate setting represents a percentage of your estimated
maximum heart rate. Note: Your maximum heart
rate is estimated by subtracting your age from
220. For example, if you are 30 years old, your
estimated maximum heart rate is 190 beats per
minute (220 – 30 = 190). Therefore, if you are 30
years old, a target heart rate setting of 50% is
equal to 95 beats per minute (50% of 190 is 95).
If you wish to change the maximum heart rate setting, press the + and – buttons beside the ENTER
button. When the desired maximum heart rate
setting is shown, press the ENTER button.
Enter a program time.
See step 5 on page 14.
Begin exercising.
During PULSE
programs, the matrix will display a
heartbeat graphic.
Each time a heartbeat is detected,
an additional peak
will appear in the
matrix.
The program is divided into 30-second segments.
One target heart rate setting is programmed for
each segment. Note: If the CONSTANT PULSE
program is selected, the same target heart rate
setting is programmed for all segments.
HOW TO USE THE INTERVAL PROGRAM
The INTERVAL program will automatically change the
resistance of the pedals to simulate a series of hills as
it guides you through an effective interval training
workout.
At the end of each segment, a tone will sound and
the resistance of the pedals will automatically
change, if necessary, to bring your heart rate
closer to the target heart rate setting for the next
segment. The program will continue in this way
until the last segment ends.
During the program, you can change the resistance of the pedals, if desired, by pressing the
RESISTANCE + and – buttons or the QUICKTOUCH RESISTANCE buttons. However, when
the current segment ends, the resistance will automatically change, if necessary, to bring your heart
rate closer to the target heart rate setting for the
next segment. Note: Each PULSE program ends
with a two-minute cool-down period. During this
period, the resistance level cannot be changed.
9
10
1
Plug in the power cord or begin pedalling to
activate the console.
2
Select the INTERVAL program.
3
If your pulse is not detected during the program,
the letters “PLS” will flash in the main display, and
the resistance of the pedals may automatically decrease. If this occurs, see the instructions included
with the chest pulse sensor.
4
5
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
6
When you are finished using the elliptical
trainer, the console will automatically enter
an idle mode or turn off.
7
See HOW TO TURN OFF THE CONSOLE on
page 10.
17
See HOW TO ACTIVATE THE CONSOLE on
page 10.
To select the INTERVAL program, press the INTERVAL button. The indicator on the button will
light, and the word “INTERVAL” will appear in the
main display for a moment.
Enter your age.
See step 3 on page 14.
Enter your weight.
See step 4 on page 14.
Enter a program time.
See step 5 on page 14.
Enter a maximum resistance setting.
See step 6 on page 15.
Enter the desired number of hills for the
program.
Next, the words “NUMBER HILLS” and the number of hills that the program will simulate will appear in the main display. If you wish to change the
number of hills, press the + and – buttons beside
the ENTER button. When the desired number of
hills is shown, press the ENTER button.
8
9
10
11
Begin exercising.
HOW TO USE THE PLATEAU PROGRAM
See step 7 on page 15.
During the PLATEAU program, the resistance of the
pedals will gradually increase, remain constant for several segments, and then gradually decrease.
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
Measure your heart rate if desired.
1
Plug in the power cord or begin pedalling to
activate the console.
When you are finished using the elliptical
trainer, the console will automatically enter
an idle mode or turn off.
2
Select the PLATEAU program.
See THE PULSE SENSOR on page 12.
See HOW TO TURN OFF THE CONSOLE on
page 10.
3
4
5
6
7
8
9
10
See HOW TO ACTIVATE THE CONSOLE on
page 10.
To select the PLATEAU program, press the
PLATEAU button. The indicator on the button will
light, and the word “PLATEAU” will appear in the
main display for a moment.
Enter your age.
See step 3 on page 14.
Enter your weight.
See step 4 on page 14.
Enter a maximum resistance setting.
See step 6 on page 15.
Enter a program time.
See step 5 on page 14.
Begin exercising.
See step 7 on page 15.
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
Measure your heart rate if desired.
See THE PULSE SENSOR on page 12.
When you are finished using the elliptical
trainer, the console will automatically enter
an idle mode or turn off.
See HOW TO TURN OFF THE CONSOLE on
page 10.
HOW TO USE THE PULSE PROGRAMS
18
4
HOW TO USE THE FOOTHILLS, PEAKS, AND
ALL-TERRAIN PROGRAMS
5
During the FOOTHILLS program, the resistance of the
pedals will gradually increase and then gradually decrease. The number of times that the resistance will increase and decrease will depend on the maximum resistance setting and the intensity level that you select.
6
During the PEAKS program, the resistance of the pedals will increase and then decrease. The number of
times that the resistance will increase and decrease
will depend on the maximum resistance setting and the
intensity level that you select.
7
During the ALL-TERRAIN program, the resistance of
the pedals will sharply increase and then sharply decrease repeatedly. The number of times that the resistance will increase and decrease will depend on the
maximum resistance setting and the intensity level that
you select.
1
Plug in the power cord or begin pedalling to
activate the console.
2
Select the desired program.
3
8
9
See HOW TO ACTIVATE THE CONSOLE on
page 10.
10
Press the FOOTHILLS, PEAKS, or ALL-TERRAIN
button. The indicator on the button will light, and
the word “FOOTHILLS,” “PEAKS,” or “ALL-TERRAIN” will appear in the main display for a
moment.
11
Enter your age.
Enter your weight.
See step 4 on page 14.
Enter a program time.
See step 5 on page 14.
Enter a maximum resistance setting.
See step 6 on page 15.
Enter an intensity level.
Next, the word “INTENSITY” and the intensity
level of the program will appear in the main display. Press the + and – buttons beside the
ENTER button to select level 1 (for a low-intensity
workout), level 2 (for a moderate-intensity workout), or level 3 (for a high-intensity workout).
Then, press the ENTER button.
Begin exercising.
See step 7 on page 15.
Follow your progress with the main display.
See THE MAIN DISPLAY on page 11.
Measure your heart rate if desired.
See THE PULSE SENSOR on page 12.
When you are finished using the elliptical
trainer, the console will automatically enter
an idle mode or turn off.
See HOW TO TURN OFF THE CONSOLE on
page 10.
See step 3 on page 14.
19
HOW TO USE THE MAINTENANCE MODE
The console features a maintenance mode that allows
you to access information and to view and change default settings. Follow the steps below to use the maintenance mode.
1
2
3
4
5
Plug in the power cord or begin pedalling to
activate the console.
See HOW TO ACTIVATE THE CONSOLE on
page 10.
Hold down the CLEAR button and the ENTER
button simultaneously for a few seconds to
select the maintenance mode.
6
Press the ENTER button again and select a
language for the main display.
7
Press the ENTER button again and select the
desired system of measurement.
8
When the maintenance mode is selected, the
words “MAINTENANCE MODE” will appear in the
main display for a moment.
The main display can display text messages in
English, International English, German, Spanish,
Italian, or French. To change the language, press
the + and – buttons beside the ENTER button.
The console can display data using the English
system (miles and pounds) or the metric system
(kilometres and kilograms). To change the system
of measurement, press the + and – buttons beside the ENTER button.
Press the ENTER button again and set the
length of time that will elapse before the console will turn off or enter the idle mode.
If the elliptical trainer is used without a power
cord, and if the pedals are stationary for a period
of time, the console will turn off. If the elliptical
trainer is used with a power cord, and if the pedals are stationary for a period of time, the console
will enter an idle mode and the words “PLEASE
SELECT A PROGRAM TO BEGIN” will begin to
scroll across the main display.
View the total number of hours that the elliptical trainer has been used.
When the words “MAINTENANCE MODE” disappear, the main display will show the total number
of hours that the elliptical trainer has been used.
Press the ENTER button and view the total
distance pedalled on the elliptical trainer.
When the button is pressed, the main display will
show the total distance pedalled on the elliptical
trainer.
9
Press the ENTER button again and set a
maximum program time for the programs.
The maximum program time for the programs can
be from 10 minutes to 90 minutes. To change the
maximum program time, press the + and – buttons beside the ENTER button.
To set the length of time that will elapse before the
console will turn off or enter the idle mode, press
the + and – buttons beside the ENTER button.
The length of time can be from 15 seconds to 2
minutes.
Hold down the ENTER button and the CLEAR
button simultaneously for a few seconds to
exit the maintenance mode.
To exit the maintenance mode at any time, hold
down the ENTER button and the CLEAR button
simultaneously for a few seconds.
20
MAINTENANCE AND TROUBLESHOOTING
Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see HOW TO CONTACT CUSTOMER CARE on page 2
of this manual.
WEEKLY MAINTENANCE
Inspect and properly tighten all external parts of the elliptical trainer. Clean the elliptical trainer with a small
amount of mild multi-purpose cleaner applied to a 100% cotton cloth. When cleaning the elliptical trainer, pay
special attention to the track and wheels. Remove all debris from the track. Clean the pedal covers with a soft
nylon brush. Do not use acidic cleaners. Doing so will void your warranty. Never spray any cleaner directly
onto the elliptical trainer.
TROUBLESHOOTING
1. SYMPTOM: THE ELLIPTICAL TRAINER IS NOT LEVEL
If the elliptical trainer rocks slightly during use, see HOW TO MOVE AND LEVEL THE ELLIPTICAL TRAINER on
page 7.
2. SYMPTOM: THE CONSOLE DOES NOT DISPLAY THE DESIRED SYSTEM OF MEASUREMENT
The console can display data using the English system (miles and pounds) or the metric system (kilometres and
kilograms). To change the system of measurement, see step 7 on page 20.
3. SYMPTOM: THE PULSE SENSOR DOES NOT FUNCTION PROPERLY
If the handgrip pulse sensor does not function properly, see THE PULSE SENSOR on page 12.
4. SYMPTOM: THE PEDAL DISKS RUB AGAINST THE SIDE SHIELDS
If a pedal disk rubs against a side shield, loosen the side shield mounting screws and move the side shield
slightly until the pedal disk stops rubbing. Retighten the side shield mounting screws.
5. SYMPTOM: THE PEDAL WHEELS SQUEAK
If the pedal wheels squeak, use a 100% cotton cloth to remove debris from the track and the wheels. If the pedal
wheels continue to squeak, apply a light coat of silicone-based lubricant to the track.
6. SYMPTOM: THE CONSOLE TURNS OFF AS SOON AS THE USER STOPS PEDALLING
If the console turns off as soon as the user stops pedalling, the battery pack may not be fully charged. The longer
the elliptical trainer is used, the longer the battery pack will maintain a charge. If the symptom continues, call
Customer Care immediately (see page 2).
21
7. SYMPTOM: THE PEDALS SLIP OR GIVE ON THE
POWER STROKE OF EACH REVOLUTION
6
If the pedals slip on the power stroke, the drive belt
is slipping. You will need to adjust the tension of the
drive belt. Remove the nine 1/4” x 3/4” Button Head
Screws (59) from the Left Side Shield (6), and pivot
the Left Side Shield to the side.
59
59
Remove the Right Side Shield (7) in the same way.
59
Note: For clarity, the left pedal disk is not shown.
Rotate the pedal disk until the Drive Belt (15) is accessible.
Loosen the four 1/4” x 3/8” Cap Screws (49 [only one
is shown]). Tighten the Generator Tension Bolt (103)
1/4 turn until the Drive Belt (15) stops slipping.
Retighten the four 1/4” x 3/8” Cap Screws, and secure the Left Side Shield with the nine 1/4” x 3/4”
Button Head Screws (59).
59
15
49
103
Secure the Right Side Shield (7) in the same way.
HOW TO REPLACE THE BATTERY PACK
If you are replacing the Battery Pack (95), see the
paragraph at the top of this page and pivot the left side
shield to the side.
Next, locate the Battery Pack (95). Disconnect the battery wire from the Lower Battery Wire (77). Cut the
wire ties and discard the Battery Pack according to
federal law.
95
Reverse this step to attach the new Battery Pack (95).
See the paragraph at the top of this page and reattach
the left side shield.
Battery
Wire
22
Wire Ties
77
EXERCISE GUIDELINES
3
FACTORS IN A SENSIBLE DIET
• Choose high-fibre, low-fat, and low-sugar
foods: fruits, vegetables, and whole grains.
• Eat at least five servings of fruits and
vegetables daily.
• Reduce red meat consumption; eat lean meat,
white meat, and fish.
• Choose healthful snacks; bring healthful foods
with you to work or in the car.
• Reduce fast food and pre-packaged meals.
• Pay attention to fat content and calories.
• Limit alcoholic beverages and caffeine.
• Drink at least eight to ten glasses of water
daily.
Be sure to check your heart rate at least twice
during an aerobic conditioning session. First,
check your heart rate five minutes into your workout to be sure that you are at the proper intensity.
Then, check it again near the end of your workout
to verify that you have maintained your target
heart rate for the recommended period of time.
EXERCISE STEPS
The following nine steps for designing your exercise
program were developed by exercise physiologists at
NordicTrack. The actual exercise you perform is only
a part of a safe and effective training program. There
are many other aspects to developing a life-long
commitment to physical fitness.
2
Establish personal fitness goals.
A medical examination or consultation with your
physician is essential.
200
180
160
140
120
100
80
TARGET HEART RATE ZONES
Pulse
Consult your physician before beginning
any exercise program.
Your target heart rate (THR), is the rate at which
you would like your heart to work during aerobic
exercise. It is expressed as a percentage of your
maximum heart rate (MHR). MHR is the maximum
number of times that your heart can pump during
one minute. To determine your approximate MHR,
subtract your age (in years) from 220. This is only
an estimation of your MHR—only clinical stress
testing can provide an actual MHR reading.
Once you have determined your MHR, you can
establish your target heart rate zone. Beginning
trainer may wish to start at 60 to 70 percent of
their MHR. This level is called the Health level.
Exercise at 70 to 85 percent of your MHR for the
optimal training, aerobic, or cardiovascular level—
the Fitness level. Advanced trainer, or those wishing to do sports, athletic conditioning, or interval
training workouts should exercise at 80 to 85 percent of the MHR for short periods of time. The
chart below shows Target Heart Rate Zones for
Health, Fitness, and Advanced trainer.
• Eat regular meals or mini-meals. Control your
portion size—don't binge or overeat. Eat
slowly.
1
Determine your target heart rate.
Set attainable, realistic goals. Reward yourself
when you meet your goals. Remember, your
goals should act as a guide for your workout
program.
25 30 35 40 45 50 55 60 65 70
Health
Beginner,
low-intensity +
long duration =
fat burning
23
Age
Fitness
Optimal training, aerobic or
cardiovascular
Advanced
Sports, athletic
conditioning,
interval training
3. Hamstring Stretch—Sit with one leg extended.
Bring the sole of the opposite foot toward you and
rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold
for 15 to 30 seconds, then relax. Repeat 3 times
for both legs. Stretches: Hamstrings, lower back,
and groin.
WEIGHT LOSS TIPS
At least four, 30-minute workouts per week,
along with a reduced-calorie diet, are
recommended if you are trying to lose weight.
However, be sure to stay within your target heart
rate zone and exercise a maximum of 5 days per
week for 60 minutes per workout.
4. Inner Thigh Stretch—Sit with the soles of your
feet together and your knees outward. Pull your
feet toward your groin area as far as possible.
Hold for 15 to 30 seconds, then relax. Repeat 3
times. Stretches: Quadriceps and hip muscles.
Good posture is the key to safe, comfortable
workouts. Keep your chin up and your head
facing forward. Align your head and shoulders
with your hips. Avoid leaning forward. Keep your
back straight.
4
5
5. Quadriceps Stretch—With one hand against a
wall for balance, reach back and grasp one foot
with your other hand. Bring your heel as close to
your buttocks as possible. Hold for 15 to 30
seconds, then relax. Repeat 3 times for each leg.
Stretches: Quadriceps and hip muscles.
Warm up before you begin.
A warm-up routine prepares your body and mind
for vigorous exercise. It also helps provide insurance against injury and soreness. Warm up with
two to five minutes of slow exercise, at minimal intensity.
1
Stretch after your warm-up.
A pliable, well-stretched muscle is less susceptible to injury. Perform the recommended stretches
on a smooth, flat surface.
3
2
The correct form for several stretches is described
below (see the drawings at the right). Be sure to
move slowly as you stretch—never bounce.
1. Toe Touch Stretch—Sit with your knees bent
slightly and slowly bend forward from your hips.
Allow your back and shoulders to relax as you
reach toward your toes as far as possible. Hold for
15 to 30 seconds, then relax. Repeat 3 times.
Stretches: Hamstrings, back of knees, and back.
4
2. Calf/Achilles Stretch—With one leg in front of
the other, reach forward and place your hands
against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front
leg, lean forward, and move your hips toward the
wall. Hold for 15 to 30 seconds, then relax.
Repeat 3 times for each leg. To cause further
stretching of the achilles tendons, bend your back
leg as well. Stretches: Calves, achilles tendons,
and ankles.
24
5
T
“T” is for the time or duration of your workout.
Beginning trainer may wish to start with 5
to 10 minutes of aerobic activity. Those in average physical condition should exercise for 20 to
30 minutes. Highly fit people, or people who want
to lose weight, should exercise for 30 to 60 minutes. The key is to maintain your target heart rate
for the duration of the workout period.
BENEFITS OF AEROBIC EXERCISE
• Effective weight loss and management
• Added protection from heart disease
• Increased strength and health of bones
• Higher levels of energy for greater productivity
during the day
• Healthy stress relief from a pressure-packed
day
• Greater intellectual capacity and productivity
6
Get FIT with NordicTrack
7
Effective aerobic exercise has three major parts:
frequency, intensity, and time. The acronym "FIT"
may help you to remember these three parts:
F
“F” stands for the frequency of your workouts. Three to five workouts per week are
recommended. Exercise at least four times a
week for weight loss.
I
“I” refers to the intensity of your workout.
Check your heart rate at least twice during
your aerobic exercise session: once during the
session and once again at the end. Maintain a
workout intensity level within your Target Heart
Rate Zone. You can measure your heart rate
using the handgrip pulse sensor or the method
described below:
8
9
1. Lower your wrist below your heart level. This
will make your heart rate stronger and easier to
feel.
2. Using the
index and
middle fingertips of your
right hand,
touch your left
wrist, onefourth inch from
your wrist joint,
at the base of your thumb.
Remember to take it slowly. Fitness is a lifelong
commitment. If you can't go the full 20 minutes
from the start, which is common, try to exercise
for five minutes at a time, a couple of times a day.
Recent research indicates that several short
workouts in one day can also provide fitness
benefits. Gradually, your stamina will increase
and it will become easier to exercise for longer
periods of time.
Cool down after aerobic exercise.
Keep moving! It is important that you cool down
properly to allow your heart rate to decrease
slowly after it has been elevated. This helps the
blood flow from your extremities back to your
heart. Keep your legs moving on the elliptical
trainer at a slower pace for at least five minutes
following the aerobic phase.
Stretch again at the end of your exercise
session.
Stretching after exercise reduces muscle soreness. See step 5 on page 24.
Participate in strength training.
"Balanced fitness, including both strength training
and aerobic exercise, can do more to ensure a
happy life than just about anything else known to
medical science today."
—Kenneth Cooper, M.D., M.P.H., founder of The
Cooper Institute For Aerobic Research, Dallas,
Texas.
A strength-training program increases your lean
muscle mass. Lean muscle mass aids in burning
body fat. With additional muscle mass and
strength, you will receive the full benefits of an exercise program. You will also be less prone to injuries during the aerobic phase of your workout.
3. Apply minimal pressure with both fingers—let
the beat come to your fingers. If you can't find
your pulse, use the opposite wrist and hand.
25
Move on to the Fitness Level only when you feel ready
and your heart rate has moved below your target heart
rate zone.
WORKOUT TIPS
Full-body conditioning helps take care of many of
life's aches and pains. However, it takes time for
your body to adapt to any new routine. Below are
some tips that will help ease you into your new
NordicTrack routine.
The Fitness level usually lasts 12 to 20 weeks. (It may
last longer, depending on your fitness goals.) At this
level you should strive to achieve your fitness goals.
Set realistic short- and long-term goals for yourself.
Frequently re-evaluate your fitness goals and reward
yourself as you are successful.
• Begin and end each exercise session with the
stretches on page 24. Stretch in a smooth,
controlled manner. Hold each stretch for 15 to
30 seconds. You may experience some initial
muscle soreness and discomfort as a result of
exercising inactive or poorly stretched
muscles. For maximum benefit, a stretching
routine must be performed every day.
Move on to the Advanced Level when you have
reached your fitness goals and your heart rate has
moved below your target heart rate zone.
Work out at the Advanced level once you have
reached your desired fitness goals. It is intended to be
a maintenance program and should continue on a regular, long-term basis.
• Be aware of your body's signals and react to
them accordingly. At your correct exercise intensity, you should be able to whistle or maintain a normal conversation. If during
exercise you feel tired, light-headed, dizzy, or
nauseated, stop exercising immediately and
consult your physician. Your heart rate may
also be affected by such things as stress,
caffeine, nicotine, or prescription drugs.
You may wish to add Interval Training to your maintenance program as well. Interval training will add variety
to your workout routine and further condition your
cardiovascular system. Interval training has been
shown to promote higher levels of aerobic conditioning. It consists of spurts of high-intensity activity followed by active rest periods of exercise at a lower intensity. For example, a one-minute spurt of high-resistance, fast exercise is followed by a two- to threeminute active rest period of low-resistance, slow exercise. The duration of these periods should be based
more on how you feel rather than time. A sequence
such as this should be repeated 5 to 20 times during
your workout session.
WORKOUT PROGRAMS
The Health level typically lasts four to six weeks. At
this level you should be concerned with slowly improving your fitness level and endurance.
Take it slowly. Set mini-goals for yourself. You may
want to begin your fitness routine with three or four
short, 5- or 10-minute workouts in a day.
Age
Heart Rate Intensity
HEALTH
FITNESS
ADVANCED
Âge
IntensitŽ du Rythme Cardiaque
SANTÉ
FITNESS
AVANCÉ
26
PART LIST
To locate the parts listed below, see the EXPLODED DRAWING on pages 29, 30, and 31.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
1
1
2
1
1
2
1
2
4
4
2
3
2
2
2
4
14
4
2
4
4
4
Description
Frame
Upright
Track Cover
Track
Pedal Disk
Left Side Shield
Right Side Shield
Step
Track Cap
Crank Spacer
Right Pedal Arm
Left Pedal Arm
Right Pedal
Left Pedal
Drive Belt
Handlebar Axle
Left Handlebar Arm
Right Handlebar Arm
Left Handlebar
Right Handlebar
Right Pedal Cover
Left Pedal Cover
Handlebar Foam
Handlebar Spacer
Pulley
Water Bottle Holder
Accessory Tray
Set Screw
Upright Cover
Generator
Wheel
Control Board
Pulse Grip
Grip Insert
Contact
Levelling foot
Foot
Pedal Wheel
Handlebar Cap
Handlebar Ring
Axle Cap
Bearing
Handlebar Bushing
Spacer
Snap Ring
Wheel Bearing
#10 x 3/4” Console Screw
Key No. Qty.
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
27
4
4
2
2
4
4
14
6
4
2
4
34
2
2
4
4
2
2
4
14
2
4
2
4
2
1
1
1
1
1
1
1
1
1
1
1
1
4
4
2
1
1
1
1
8
4
4
Description
R1104A
3/8” x 1 1/4” Button Head Screw
1/4 x 3/8” Cap Screw
1/2” x 2” Button Head Screw
#4 Nylon Locknut
#8 x 3/4” Screw
#8 x 1/4” Nylon Screw
#10 x 3/8” Pedal Screw
3/8” x 3/4” Shoulder Screw
1/4” x 3/4” Axle Screw
#4 x 1/2” Screw
#10 x 3/4” Screw
1/4” x 3/4” Button Head Screw
5/16” Nylon Locknut
5/16” x 3 1/2” Cap Screw
3/8” x 3/4” Cover Screw
3/8” x 3” Screw
Long Side Shield Spacer
Key
Axle Washer
#10 Washer
1/4” Pedal Washer
#6 x 1” Screw
1/2” Nylon Locknut
Standoff
3/8” Nylon Locknut
Short Side Shield Spacer
Power Cord (TV Console Only)
Power Supply (TV Console Only)
Pulse Jumper Wire
Lower Battery Wire
Upper Battery Wire
Upper Controller Wire
Lower Controller Wire
Generator Coil Wire
Electromagnet Wire
Left Crank Arm
Right Crank Arm
3/8” Star Washer
#10 Star Washer
4” Foam Grip
Control Console
Display Console
Accessory Tray Foam
Bottle Holder Foam
#8 x 1/2” Button Head Screw
Wheel Spacer
Wave Washer
Key No. Qty.
95
96
97
98
99
100
101
1
1
1
1
8
4
1
Description
Battery Pack
Lower Power Wire
Upper Power Wire
Power Input Wire
Pedal Bushing
3/8” x 5/8” Shoulder Screw
Upper CATV Cable
Key No. Qty.
102
103
#
#
#
#
#
1
1
1
2
2
1
2
Description
Lower CATV Cable
Tension Bolt
User’s Manual
Hex Key
Bookrack
Audio Plug
Side Shield Trim
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.
If replacement parts are needed, or if parts are missing or damaged, see HOW TO CONTACT CUSTOMER
CARE on page 2 of this manual.
28
EXPLODED DRAWING
35
34
33
34
69
89
87
69
35
49
Part 1 of 3 R1104A
30
86
47
86
29
88
47
48
90
87
2
86
27
92
48
85
69
34
85
103
70
31 46
46
70
92
42
31 46
46
50
95
36
36
1
50
51
57
92
75
101
34
33
26 35
76
77
78
79
80
15
81
82
98
32
71
69
97
96
53
25
42
102
74
35
37
59
37
59
29
37
59
91
Part 2 of 3 R1104A
59
5
59
64
73
7
59 9
59
63
52
8
63
52
3
59
59
52
62
58
4
59
5
9
62
6
59
59
59
30
52
Part 3 of 3 R1104A
42
39
23
20
100
41
56
39
18
42
40
13
84
100
24 72
10
65
60
17
24
45
23
16
40
66 42
41 94
56 45
55
66
42
19
43
94
56
41
45
66
94
42
42
44
12
55
14
55
28
22
43
99
83
61
21
11
99
67
54
99
67
67
31
54
99
93
38
93
68 59
FreeMotion Fitness, Inc. • 1096 Elkton Drive, Suite 600 • Colorado Springs, CO 80907
Part No. 222113 R1104A Printed in USA
32
© 2004 ICON IP, Inc.
Download PDF