712
10 Sunnen Drive
St. Louis, MO 63143
telephone: 314-678-6336
fax: 314-781-2714
www.bloomfieldworldwide.com
OWNERS MANUAL
for
HOT WATER
DISPENSER
2 GALLON MODELS:
1222
1222CA
5 GALLON MODELS:
1225
1226
Includes:
Installation
Operation
Use & Care
Servicing Instructions
Model 1222 Dispenser
2M-76580 Rev. I
M712
110215
WARRANTY STATEMENT
All equipment manufactured by Bloomfield is warranted against defects
in materials and workmanship for the time periods listed in the chart
starting from the date the equipment is placed into service and is for the
benefit of the original purchaser:
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN LIEU
OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE
HEREBY EXCLUDED.
BLOOMFIELD, LLC SHALL NOT BE LIABLE FOR INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES
FROM ANY CAUSE WHATSOEVER.
Equipment
pour over, automatic coffee brewers
EBC, EMAX coffee brewers
* EBC, EMAX coffee brewer control
POD coffee brewers
ECO coffee brewers
coffee warmers
tea brewers
tea dispensers
tea dispenser BBTea
hot water machines
thermal servers
airpots
decanters
This warranty is void if it is determined that upon inspection by an
authorized service agency that the equipment has been modified,
misused, misapplied, improperly installed, or damaged in transit or by fire, flood or act of God.
Parts
2 yrs.
2 yrs.*
3 yrs.
1 yr.
1 yr.
1 yr.
2 yrs.
1 yr.
1 yr.
2 yrs.
90 days
30 days
no warranty
Labor
2 yrs.
2 yrs.
no labor
1 yr.
1 yr.
1 yr.
2 yrs.
1 yr.
no labor
2 yrs.
no labor
no labor
no warranty
It also does not apply if the serial nameplate has been removed or unauthorized service personnel perform service. The prices
charged by Bloomfield for its products are based upon the limitations in this warranty. Seller’s obligation under this warranty
is limited to the repair of defects without charge by a Bloomfield Authorized Service Agency or one of its sub-agencies. This
service will be provided on customer’s premises for non-portable models. Portable models (a device with a cord and plug or a
dispenser) must be taken or shipped to the closest authorized service agency, transportation charges prepaid, for services.
Agencies are located in principal cities, please visit our website to locate one.
This warranty is valid in the United States and Canada and void elsewhere. Please consult your classified telephone directory
or your food service equipment dealer; or, for information and other details concerning warranty, write to:
Service Parts Department; Bloomfield
10 Sunnen Drive, St. Louis, MO 63143
Phone: (314) 678-6336 : Fax: (314) 781-2714
Technical@ bloomfieldworldwide.com / www.bloomfieldworldwide.com
1. Resetting of safety thermostats, circuit breakers, overload protectors, or fuse replacements.
2. All problems due to operation at voltages other than specified on equipment nameplates - conversion to correct voltage
must be the customer’s responsibility.
3. All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams
supplied with the equipment.
4. Replacement of items subject to normal wear, to include such items as knobs and light bulbs. Normal maintenance
functions including adjustment of thermostats, microswitches, and replacement of fuses and indicating lights are not
covered under warranty.
5. All problems due to inadequate water supply, such as fluctuating, or high or low water pressure.
6. All problems due to mineral/calcium deposits, or contamination from chlorides/chlorines. De-liming is considered a
preventative maintenance function and is not covered by warranty.
7. Full use, care and manuals may or may not be sent with each unit, only a condensed version. Please visit our web site to
download the full version.
8. Travel mileage is limited to fifty (50) miles from an authorized service agency or one of its sub-service agencies.
9. All labor shall be performed during normal working hours. Overtime premium shall be charged to the customer.
10. All genuine Bloomfield replacement parts are warranted for ninety (90) days from date of purchase on non- warranted
equipment. Any use of non-genuine Bloomfield parts completely voids any warranty.
11. Installation, labor and job checkouts are not considered warranty.
12. Charges incurred by delays, waiting time or operating restrictions that hinder the service technicians ability to perform
services are not covered by warranty. This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled
personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility
for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt,
and that the note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done
within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.
Bloomfield cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the
necessary documents to support your claim.
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
BLOOMFIELD SERVICE POLICY AND PROCEDURE GUIDE ADDITIONAL WARRANTY EXCLUSIONS
TABLE OF CONTENTS
WARRANTY STATEMENT
SPECIFICATIONS
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY LISTING INFORMATION
INSTALLATION INSTRUCTIONS
OPERATION
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
SERVICING INSTRUCTIONS
Deliming Instructions
EXPLODED VIEW & PARTS LIST
WIRING DIAGRAMS
xi
1
2
3
3
4
6
7
8
9
12
13
16
Thank You for purchasing this
Wells Bloomfield appliance.
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
SPECIFICATIONS
MODEL
VOLTS
1ø 50/60Hz
WATTS
AMPS
1ø
1222
120
1800
15
1222CA
120
1500
12.8
1225
208
4000
19
1226
240
4000
16.5
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
Meets Canadian standards
APPLICABILITY
This manual applies to the following Wells Bloomfield products:
1222 1222CA 1225 1226 2-Gallon Hot Water Dispenser
2-Gallon Hot Water Dispenser
5-Gallon Hot Water Dispenser
5-Gallon Hot Water Dispenser
1
POWER SUPPLY
CORD
NEMA 5-15P
NEMA 6-30P
FEATURES AND OPERATING CONTROLS
REAR COVER
REAR VIEW
FRONT VIEW
THERMOSTAT
ACCESS
READY LITE
POWER LITE
HO
TW
FLEXIBLE
DRAIN LINE
AT
E
R
WATER SUPPLY
CONNECTION
TANK HEATER
SWITCH
DRAIN LINE
TUBING CLAMP
POWER CORD
RUBBER
GRIP FEET
2
IL2081
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
DISPENSE
FAUCET
PRECAUTIONS AND GENERAL INFORMATION
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated components must be performed by qualified
service personnel. Do not open any access panels which require the use of tools.
Failure to heed this warning can result in electrical shock.
WARNING: INJURY HAZARD
All installation procedures must be performed by qualified personnel with full knowledge of all
applicable electrical and plumbing codes. Failure could result in property damage and
personal injury.
WARNING: ELECTRIC SHOCK HAZARD
Hot Water Dispenser must be properly grounded to prevent possible shock hazard.
DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death
or serious Injury.
WARNING: BURN HAZARD
This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from
contact with dispensed liquids.
This appliance is intended for commercial use only.
This appliance is intended for use to dispense heated
water. No other use is recommended or authorized by the
manufacturer or its agents.
This appliance is intended for use in commercial establishments,
where all operators are familiar with the appliance use,
limitations and associated hazards. Operating instructions and
warnings must be read and understood by all operators and
users.
Except as noted, this piece of equipment is made in the USA
and has American sizes on hardware. All metric conversions are
approximate and can vary in size.
The following trouble shooting, component views and parts lists
are included for general reference, and are intended for use by
qualified service personnel.
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
This manual should be considered a permanent part of this
appliance. The manual must remain with the appliance if it is
sold or moved to another location.
CAUTION:
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and followed.
Damage to the dispenser will
occur if these instructions are not
followed.
CAUTION:
BURN HAZARD
Dispensed liquid is VERY HOT
and can cause burns.
CAUTION:
BURN HAZARD
Exposed surfaces of the
appliance may be HOT to the
touch and can cause burns.
AGENCY LISTING INFORMATION
This dispenser is
and
listed under file E9253.
This dispenser meets
Standard 4 only when installed,
operated and maintained in accordance with the enclosed
instructions.
E9253
STANDARD 4
3
E9253
INSTALLATION
READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION
CAUTION:
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and
followed. Damage to the
dispenser will occur if these
instructions are not followed.
CAUTION:
UNSTABLE
EQUIPMENT HAZARD
It is very important for safety
and for proper operation that
the dispenser is level and
stable when standing in its final
operating position. Provided
adjustable, non-skid legs must
be installed at each corner
of the unit. Failure to do so
will result in movement of the
dispenser which can cause
personal Injury and/or damage
to appliance.
NOTE: Water supply inlet line
must meet certain minimum
criteria to insure successful
operation of the dispenser.
Bloomfield recommends 1/4”
copper tubing for installation of
less than 12 feet and 3/8” for
more than 12 feet from a 1/2”
water supply line.
REFER TO EXPLODED VIEWS PAGE 14 FOR COMPONENT
NAMES/NUMBERS.
Unpack the unit. Inspect all components for completeness and
condition. Ensure that all packing materials have been removed
from the unit.
LEVELING THE UNIT
Two Gallon Dispenser is NOT provided with adjustable legs. Be
sure dispenser is placed on a solid level surface with all four feet
touching the surface.
Five Gallon Dispenser is provided with adjustable legs. Verify
that an adjustable leg is installed at each corner of the brewer.
Set Brewer in its operating location. Level the Brewer. A spirit
level should be placed on the top of the unit, at the edge, as a
guide when making level adjustments. Level the unit from left to
right and front to back by turning the adjustable feet. Be sure all
four feet touch the counter to prevent tipping.
PLUMBER’S INSTALLATION INSTRUCTIONS
Dispenser should be connected to a POTABLE WATER, COLD
WATER line. Flush water line before connecting to appliance.
DO NOT use a saddle valve with a self-piercing tap for the water
line connection. Such a tap can become restricted by waterline
debris. For systems that must use a saddle tap, shut off the
main water supply and drill a 3/16” (minimum) tap for the saddle
connection, in order to insure an ample water supply. Remember
to flush the line prior to installing the saddle.
The dispenser must be installed on a water line with average
pressure between 20 PSI and 90 PSI. If your water pressure
exceeds 90 PSI at anytime, a pressure regulator must be
installed in the water supply line to limit the pressure to not more
than 90 PSI in order to avoid damage to lines and solenoid.
A water shut-off valve should be installed on the incoming water
line in a convenient location (Use a low restriction type valve,
such as a 1/4-turn ball valve, to avoid loss of water flow thru the
valve.
4
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
IMPORTANT:
To enable the installer to make
a quality installation and to
minimize installation time, the
following suggestions and tests
should be done before the
actual unit installation is started:
INSTALLATION (continued)
NSF requires that the unit be able to be moved for cleaning
underneath. A flex line or loops of copper tubing will satisfy this
requirement. See Figure 2 below.
COPPER LOOPS OR
FLEX LINES
(PROVIDED BY
PLUMBER)
SOLENOID
STRAINER
WASHER
SHUT-OFF VALVE
(PROVIDED BY
PLUMBER)
WATER
SUPPLY
CAUTION:
SHOCK HAZARD
WATER INLET
FITTING
FLOW
IL2351
Fig. 2 Water Supply Installation
In some areas, local codes require a backflow preventer (check
valve) to be installed on the inlet water line. If a backflow
preventer is used, you must install a water hammer arrester in the
incoming line, between the backflow preventer and the brewer
inlet, as far away from the brewer as space will allow. This will
relieve the excessive back pressures that can cause faucet leaks
and solenoid malfunctions.
ELECTRICIAN’S INSTALLATION INSTRUCTIONS
REFER TO ELECTRICAL SPECIFICATIONS - Page 1
Check the nameplate to determine correct electrical service
required for the dispenser to be installed.
IMPORTANT: Before connecting to electricity, make sure
dispenser is connected to the water supply.
Model 1222 is equipped with a cord and plug. It requires a
115 - 125 volt 20 amp circuit (50/60 Hz, 2 wire plus ground, with
NEMA 5-15R).
Model 1222CA is equipped with a cord and plug. It requires a
115 - 125 volt 15 amp circuit (50/60 Hz, 2 wire plus ground, with
NEMA 5-15R).
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
NOTE: This equipment must
be installed to comply with
applicable federal, state and
local plumbing codes and
ordinances.
CAUTION: EQUIPMENT DAMAGE
DO NOT connect Model 1225 to a circuit with voltage higher than 208V. Equipment damage will result.
Such damage is NOT covered by warranty.
Model 1225: is equipped with a cord and plug. It requires
a 208V, 30 amp circuit (50/60 Hz, 2 wire plus
ground, with NEMA 6-30R).
Model 1226: is equipped with a cord and plug. It requires
a 240V, 30 amp circuit (50/60 Hz, 2 wire plus
ground, with NEMA 6-30R).
5
Dispenser must be properly
grounded to prevent possible
shock hazard. DO NOT
assume a plumbing line
will provide such a ground.
Electrical shock will cause death
or serious injury.
IMPORTANT:
Supply power must match
nameplate for voltage and
phase. Connecting to the
wrong voltage will damage the
appliance or result in decreased
performance. Such damage is
not covered by warranty.
IMPORTANT: Do not connect
dispenser to electrical power
until you are ready to fill the
tank.
IMPORTANT: The ground
prong of the plug is part of a
system designed to protect
you from electrical shock in
the event of internal damage.
Never cut off the ground prong
nor twist a blade to fit an
existing receptacle. Contact a
licensed electrician to install the
proper circuit and receptacle.
OPERATION
WATER HEATER
Water temperature is sensed by thermobulb
inserted into the water tank. Temperature is
controlled by a mechanical thermostat.
The setpoint temperature is adjustable by
turning the thermostat shaft.
Excessive temperature will trip the hi-limit
safety switch, disabling the heating element.
The hi-limit will automatically reset when the
dispenser cools.
WATER LEVEL
Water level is controlled by an electronic
controller. The water level probe senses
chassis ground through the water. When the
water level is below the probe no ground is
sensed. The controller opens the fill solenoid
until the water level makes contact with the
probe.
Fig. 3 Dispenser Operation Diagram
A. START-UP
For initial start-up, or if the dispenser has not been used for an
extended period of time:
•• Be sure the water supply is properly connected and the water
supply valve is turned ON.
•• Be sure the WATER TANK IS FILLED.
IMPORTANT: Fill the water tank before energizing tank heater:
1. Be sure TANK HEATER SWITCH is “OFF”, then plug unit into an appropriate receptacle. “POWER” light will glow any time unit is connected to electric power.
2. The fill solenoid will open and water tank will begin filling.
3. When the fill solenoid shuts off, open the faucet. Run water until the fill solenoid is energized again, then close the faucet. This will
purge all air from the system. When fill solenoid shuts off, tank is
filled.
4. Press tank heater switch to “ON”. Tank heaters will energize.
When the “HOT WATER READY” light glows, water is ready to use.
A. USE
1. Always use a container suitable for hot water.
2. Hold container under faucet. Pull faucet handle to dispense hot water. Release handle to stop dispensing.
6
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
IMPORTANT:
Be sure tank is filled with
water before pressing
tank heater switch to ON.
CLEANING INSTRUCTIONS
PROCEDURE: Clean Hot Water Dispenser
PRECAUTIONS: Disconnect dispenser from electric power.
Allow dispenser to cool.
FREQUENCY: Daily
TOOLS: Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush
CAUTION:
BURN HAZARD
Dispensed water is extremely
hot. Hot water will cause
serious skin burns.
CAUTION:
SHOCK HAZARD
Do not submerge or immerse
dispenser in water.
1. Disconnect dispenser from electric power.
Allow to cool before cleaning.
2. Wipe exterior of dispenser with a soft clean cloth or sponge
moistened with mild detergent and clean water. Rinse by
wiping with a soft clean cloth or sponge moistened clean
water.
3. Wipe faucet nozzle to remove any mineral deposits. A
bristlebrush may be used to remove stubborn mineral
build-up.
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
Procedure is complete
7
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the dispenser’s stainless steel
surfaces.
TROUBLESHOOTING SUGGESTIONS
Water won’t heat
No flow from hot water
faucet
Water faucet drips
POSSIBLE CAUSE
SUGGESTED REMEDY
Dispenser unplugged or circuit breaker
tripped
Check power supply cord
Tank heater switch “OFF”
Press switch to “ON”
Temperature setpoint too low
Adjust thermostat for desired temperature
Hi-Limit safety switch tripped
Allow to cool hi-limit will self-reset
Damaged internal component or wiring
Examine wiring & connectors, controller,
power board and heating element. Repair/
replace as needed
Water supply OFF
Turn water supply ON
Solenoid inlet strainer plugged
Clean strainer
Water filter (if used) plugged
Replace filter element
Faucet plugged
Disassemble faucet, clean
Debris in faucet seat
Disassemble faucet, clean
Faucet damaged
Examine faucet, repair or replace as needed
8
Check / reset circuit breaker
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
SYMPTOM
SERVICING INSTRUCTIONS
ACCESS PANELS
CAUTION:
REAR PANEL:
Remove rear panel to access hot water tank, thermostat,
heating elements, tubing, water level control and plumbing
connections.
Rear panel is held by four screws at the back. The flanged top
portion fits over the body of the dispenser.
SOLENOID DOOR:
Solenoid door may be removed to aid in solenoid replacement.
This access panel is not normally removed.
Solenoid door is held by two screws and a retaining lip.
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
BUTTON PLUG:
Remove button plug to adjust thermostat temperature setting.
Fig. 3 Access Panels
9
SHOCK HAZARD
Opening access panels on
this dispenser may expose
uninsulated electrical
components.
Disconnect dispenser from
electrical power before
removing any panel.
SERVICING INSTRUCTIONS (continued)
TEMPERATURE ADJUSTMENT
Check temperature at discharge of faucet.
Remove thermostat access button plug to access thermostat.
Turn thermostat shaft clockwise to increase temperature.
IMPORTANT:
The thermostat will maintain
temperature within ±3ºF.
For high altitude locations,
thermostat should be adjusted
to a maximum temperature
equal to the local boiling
temperature minus 5º. This
will prevent boiling water in the
dispenser,
NOTE:
Thermostat is adjustable to a
maximum of 199ºF.
REMOVE TANK LID ASSEMBLY
Unplug dispenser or turn circuit breaker OFF. Turn OFF water
supply. Remove rear panel.
Disconnect fill tube and vent tube from tank lid. Disconnect
wiring from hi-limit, thermostat and heating element as necessary.
Remove eight lid screws Remove lid assembly by lifting it
straight up.
Reassemble in reverse order.
REPLACE THERMOSTAT
IMPORTANT:
Water pressure must be
between 20 p.s.i and 90 p.s.i.
flowing pressure. If water
pressure exceeds this value, or
if water pressure varies greatly,
a pressure regulator must be
installed in the water supply line.
IMPORTANT:
Before setting lid assembly into
tank, make sure tank lid gasket
is properly seated on flange of
lid.
Unplug dispenser. Remove back panel.
Loosen and free jam nut from pass-thru fitting securing
thermobulb. Lift out probe, jamb nut and gasket. Disconnect
wiring from thermostat. Loosen screws holding thermostat to
bracket. Remove thermostat.
10
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
Reassemble in reverse order.
SERVICING INSTRUCTIONS (continued)
REPLACE HEATING ELEMENT
Remove tank lid assembly as detailed on page 10.
Remove two hex nuts holding element to cover. Pull element
from mounting holes.
IMPORTANT:
When replacing heating
element, also replace seal
gaskets.
Reassemble in reverse order.
REPLACE SOLENOID
Unplug power cord. Turn OFF and disconnect water supply from
dispenser inlet fitting.
Remove rear panel. Remove two screws holding access door in
place. Remove access door and solenoid. Unscrew inlet fitting
cap to release solenoid from door. Remove wiring from solenoid.
Transfer fill tube from old solenoid to new solenoid.
Reassemble in reverse order.
REPAIR HOT WATER FAUCET
Unplug power cord. Turn OFF water. Unscrew bonnet from
faucet, then pull bonnet assembly from faucet body.
Examine the interior of the faucet body and the surface of the
seat cup. Clean out any debris in the faucet body, using a stiff
bristle brush if necessary.
If required, work the seat cup out of the bonnet and off of the end
of the stem. Install a new seat cup, making sure the knob on the
stem is fully inserted into the pocket of the seat cup, and the skirt
of the seat cup is fully inserted into the bonnet
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
Reassemble in reverse order.
11
NOTE: Any abrasion or
roughness on the flat end of the
seat cup will require replacing
the seat cup:
SERVICING INSTRUCTIONS (continued)
CHEMICAL BURN
HAZARD
Deliming chemicals may be
caustic. Wear appropriate
protective gloves and goggles
during this procedure. Never
siphon deliming chemicals or
solutions by mouth.
This operation should only be
performed by qualified and
experienced service personnel.
IMPORTANT: DO NOT spill,
splash or pour water or deliming
solution into or over any internal
component other than the inside
of the water tank.
IMPORTANT: DO NOT allow
any internal components to
come into contact with the
deliming solution. Take care to
keep all internal components
dry.
NOTE: Repeat steps 4 thru 5
as required to remove all scale
and lime build-up.
NOTE: Normally, silicone
hoses do not need to be
delimed. Should deliming hoses
become necessary, Bloomfield
recommends replacing the
hoses
PROCEDURE: Delime the Water Tank
PRECAUTIONS: Disconnect dispenser from electric power.
Allow dispenser to cool.
FREQUENCY: As required (dispenser slow to heat)
TOOLS: Deliming Solution
Protective Gloves, Goggles & Apron
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Large Sink (or other appropriate work area)
1. Unplug power cord. Turn off the water shut-off valve and disconnect the water supply line from the inlet fitting.
2. Remove the tank lid assembly as detailed on page 10.
3. Using the drain tube, drain all water from water tank. When
finished, be sure drain tube clamp is secured.
4. Mix 2 gallons of deliming solution according to the manufacturer’s directions. Carefully pour the deliming solution into
the water tank. Lower the lid assembly back onto the tank.
Allow to sit for 30 minutes, or as directed by the manufacturer.
5. At end of soaking period, remove lid assembly from tank. Thoroughly rinse internal components of lid assembly with clear water. Using a stiff bristle brush, scrub the heating element to remove lime and calcium build-up. Rinse with clean water. Store lid assembly in a safe location.
6. Drain the water tank. Using a stiff bristle brush, scrub the interior of the water tank to remove lime and calcium build-
up. Rinse with clean water.
7. Reassemble the tank lid to the water tank. Make sure the gasket is properly in place. Reinstall wiring to heating
element and thermostat. Reinstall fill and vent tubes.
8. Reconnect water supply. Plug in power cord.
9. Allow dispenser to fill, then drain. Repeat three times.
10.Press tank heater switch “ON”. When ready light glows, dispenser is ready to use.
12
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
CAUTION:
EXPLODED VIEWS AND PARTS LISTS
HO
TW
AT
E
R
BONNET &
PLUNGER
ASSY.
FAUCET
ASSY
SEAT CUP
2U-71460
INLET FITTING KIT
WS-85218
SCREEN WS-85219
WASHER
FITTING
CAP
FAUCET
BODY
SHANK ASSY
(Tank Fitting)
SERVICE KITS
FAUCET REPAIR KITS
WS-86597 Faucet & Shank Complete (1222, 1222CA)
2U-71460 Seat Cup (only)
2U-84396 Shank Assy, Faucet
2U-87030 Faucet Assy Brass (1225, 1226)
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
SOLENOID REPAIR KITS
2E-73612 Solenoid Complete, Single 120V (1222, 1222CA)
2E-75760 Solenoid Complete, Single 240V (1225, 1226)
WS-85218 Inlet Fitting Kit (includes cap, fitting, washer & screen)
WS-85219 Inlet Strainer (only)
13
IL2080
EXPLODED VIEW & PARTS LIST
27
3
19
2 REQD
40
28
29
2 REQD
18
36
32
26
20
24
31
21
35
22
23
25
21
12
2
10
5
9
13
4
11
6
8
7
16
15
14
34
38
39
17c
17b
17
17a
34
37
1
30
HOT WATER DISPENSER
NOTE: Model 1225/1226 shown. Model 1222/1222CA is similar.
14
IL2065b
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
17d
EXPLODED VIEW & PARTS LIST (continued)
ITEM
DESCRIPTION
1222 P/N
1222CA P/N
1225 P/N
WRAP, BODY
C7-76579
C7-76709
2
TANK ASSY
C7-76578
C7-76710
3
PANEL, TOP BACK
C7-76512
4
PLUG, BUTTON 7/8”
5
SUPPORT, TANK
6
LABEL, HW DISPENSER
7
LIGHT, PILOT GREEN
2J-72671
2J-35697
8
LIGHT, PILOT AMBER
2S-41778
2J-30516
CONTROL, LOW WATER, 120V
2E-46604
9
SPACER, NYLON
11
PANEL, REAR LOWER
C7-76712
2M-76568
2E-306865
2A-43201
C7-76716
2E-73612
SOLENOID SINGLE 240V
DOOR, ACCESS
14
SWITCH, ROCKER 250V
15
STRAIN RELIEF
16
CORDSET
17a
C7-76521
SOLENOID, SINGLE 120V
13
17
C7-76713
2P-70714
CONTROL, LOW WATER, 240V
10
12
2E-75760
2Q-75089
2E-305295
2E-302541
2K-Y6764
2E-35259
FAUCET & SHANK ASSY PLASTIC
WS-86597
FAUCET & SHANK ASSY BRASS
WS-84686
FAUCET ASSY (plastic)
2U-87038
FAUCET ASSY (brass)
2U-87030
2U-84396
2U-87030 (BRASS)
17b
SHANK ASSY FAUCET
2U-84396
17c
WASHER FIBER
2C-84489
17d
FERRULE-VALVE SHANK
2A-84488
18
ELBOW, OUTLET
2K-70103
19
TUBE, 3/8 x 3/4” LONG
2A-75609
20
TUBE, SILICONE .312 DI x 25” LONG
A6-73540
21
TUBE, BRAIDED .312 ID x 21” LONG
A6-76237
22
CLAMP, HOSE SHUT OFF
2C-76564
23
GASKET, HEATING ELEMENT
24
GASKET, TANK
2I-70152
2I-76514
HEATING ELEMENT, 120V 1800W
25
2I-76776
2N-76524UL
HEATING ELEMENT, 120V 1500W
2N-76571UL
HEATING ELEMENT 208V 4000W
2N-76721UL
HEATING ELEMENT 240V 4000W
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
1226 P/N
1
2N-76720UL
26
LID ASSY
C7-76527
C7-76726
27
THERMOSTAT, TEMPERATURE CONTROL
28
TUBE, TANK FILL
2V-76570
29
PROBE, LIQUID LEVEL
C7-75746
30
FOOT, 1/2” HIGH BLACK RUBBER
2A-305148
31
THERMOSTAT, HI-LIMIT SAFETY
2T-47499
32
GROMMET, 3/8 ID
2I-72390
33
SLEEVE, WATER LEVEL PROBE
2A-73532
34
SPACER, TANK SATELLITE
2A-74316
35
ELBOW, OUTLET
2K-70130
36
SPACER, SIDE
C7-76781
37
RELAY, SOLID STATE
2E-76769
38
PLATE, HEAT SINK
39
BRACKET, HEAT SINK
40
CABLE TIE
WS-8512-51
SEAL, THERMOBULB
2A-40564
2T-70716
2C-70174
15
WIRING DIAGRAM
16
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
2-GALLON MODELS 1222 and 1222CA
WIRING DIAGRAM (continued)
5-GALLON MODELS 1225 and 1226
HOT WATER
READY LIGHT
(AMBER)
POWER
LIGHT
(GREEN)
BLACK
7
7
THERMOSTAT
9
5
BLACK
WATER
LEVEL
CONTROL
BOARD
COMM
N.O.
WATER
LEVEL
PROBE
TANK
HEATER
SWITCH
N.C.
3
MAX
11
GREEN
6
WHITE
BLACK
13
WHITE
1
240V POWER CORD
NEMA 6-30P
BLACK
GREEN
FILL
SOLENOID
WHITE
MODEL: 1225 & 1226
RED12ga.
ON
2
712 p/n 2M-76580 1222_1225_1226 Owmers Manual
HI-LIMIT
INPUT
COMM
12
10
OFF
BLACK
WHITE
HEATING ELEMENT
4000 WATTS
WHITE
RED 12 ga.
4
BLACK
MODEL
1225
1226
VOLT
208
240
17
AMPS
19
16.5
Hz
50/60
50/60
BLACK
BLACK
2E-Z13318
8
10 Sunnen Drive, St. Louis, MO 63143
telephone: 314-678-6336 fax: 314-781-2714
www.bloomfieldworldwide.com
Download PDF