42, 54 & 72
ProBuilder MV
Owner’s Manual
WARNING: FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Leave the building immediately
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Tested and Listed by
HOT GLASS WILL CAUSE
BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals.
(42 MV) Report # 0028GF105S
(54 MV) Report # 0028GF105S
REV.002
(72 MV) Report # 0028GF105S-001
Omni-Test Laboratories, Inc.
Portland, Oregon
ANSI Z21.88-2016
CSA 2.33-2016
• Operation
• Maintenance
This appliance may be installed in an aftermarket, permanently located, manufactured home
(USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. A conversion
kit is supplied with the appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Travis Industries, Inc.
 Copyright 2017, T.I.
12521 Harbour Reach Dr., Mukilteo, WA 98275
$10.00
3/16/18
www.travisproducts.com
100-01452
2
Table of Contents
Introduction
We welcome you as a new owner of a ProBuilder gas fireplace. This manual details operation and
maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your
heater and save the manual for future reference.
Important Information
No other ProBuilder gas fireplace has the same serial
number as yours. The serial number is on the listing
label that is chained to the gas control valve. This
serial number may be needed in case you require
service.
Model:
42 ProBuilder MV
54 ProBuilder MV
72 ProBuilder MV______
Register your warranty online at:
traviswarranty.com
Or, mail your warranty card to:
Travis Industries House of Fire
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275
Save Your Bill of Sale.
Serial Number:
Purchase Date:
Purchased From:
To receive full warranty coverage, you will
need to show evidence of the date you
purchased your heater. Do not mail your Bill
of Sale to us.
We suggest that you attach your Bill of Sale
to this page so that you will have all the
information you need in one place should the
need for service or information occur.
Installation Warnings
•
•
•
•
•
•
•
•
Installation requirements are printed in the ProBuilder Installation Manual. All
requirements in the installation manual must be met.
Failure to follow all of the requirements may result in property damage, bodily injury,
or even death.
This heater must be installed by a qualified installer who has gone through a training
program for the installation of direct vent gas appliances.
This appliance must be installed in accordance with all local codes, if any; if not,
follow ANSI Z223.1 and NFPA 54(88). In Australia follow AS/NZS 5601.1.
In Manufactured or Mobile Homes must conform with Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard
is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS
A225.1. This appliance may be installed in Manufactured Housing only after the
home is site located.
The fireplace is designed to operate on natural gas, or propane (LP).
All exhaust gases must be vented outside the structure of the living-area.
Combustion air is drawn from outside the living-area structure.
Notify your insurance company before hooking up this fireplace.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
Introduction
3
Table of Contents
Introduction ................................................... 2
Important Information ................................... 2
Installation Warnings .................................... 2
Table of Contents .......................................... 3
Features ......................................................... 3
Heating Specifications .................................. 3
Before You Begin .......................................... 6
Location of Controls ..................................... 6
Starting the Pilot............................................ 7
Starting the Heater for the First Time.......... 8
Turning the Heater On and Off ..................... 8
Adjusting the Flame Height .......................... 8
Adjusting the Blower Speed (Optional) ...... 8
Normal Operating Odors .............................. 9
Power Outages .............................................. 9
Crushed Glass Installation......................... 13
Maintaining Your Heater's Appearance .... 14
Cleaning The Glass ........................................... 14
Cleaning the Fireplace ...................................... 14
Yearly Service Procedure........................... 15
Troubleshooting Table ............................... 16
Replacement Parts List .............................. 17
Wiring Diagram ........................................... 18
Optional Blower Wiring ...................................... 18
Safety Label ...................................................... 19
CONDITIONS & EXCLUSIONS ................... 22
IF WARRANTY SERVICE IS NEEDED: ...... 22
Index ............................................................. 24
Features
•
•
•
•
•
•
•
Works During Power Outages
Contemporary Look
Optional Blower for Heat Distribution
Optional Remote Thermostat
Standing Pilot
Variable-Rate Heat Output
Low Maintenance
Heating Specifications
42 ProBuilder
54 ProBuilder
72 ProBuilder
*
Natural Gas
Propane
Up to 1,250
Up to 1,250
25,000
25,000
Up to 1,650
Up to 1,650
Maximum BTU Input Per Hour
33,000
33,000
Approximate Heating Capacity (in square feet)*
2,250
2,250
Maximum BTU Input Per Hour
45,000
45,000
Approximate Heating Capacity (in square feet)*
Maximum BTU Input Per Hour
Approximate Heating Capacity (in square feet)*
Heating capacity will vary with floor plan, insulation, and outside temperature.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
4
Safety Precautions
IF YOU SMELL GAS:
* Do not light any appliance
* Extinguish any open flame
* Do not touch any electrical switch or plug or unplug anything
* Open windows and vacate building
* Call gas supplier from neighbor's house, if not reached, call fire department
This unit must be installed by a qualified installer to prevent the possibility of an explosion.
Your dealer will know the requirements in your area and can inform you of those people
considered qualified. The room heater should be inspected and cleaned before use and at
least annually by a qualified service person. More frequent cleaning may be required due
to excessive lint from carpeting, bedding material, etc.
The instructions in this manual must be strictly adhered to. Do not use makeshift methods
or compromise in the installation. Improper installation will void the warranty and safety
listing.
This heater is either approved for natural gas (NG) or for propane (LP). Burning
the incorrect fuel will void the warranty and safety listing and may cause an
extreme safety hazard. Direct questions about the type of fuel used to your dealer.
Check for a label on the flame adjust knob on the gas control valve (this is the best
place to check). You may also check for a label on the gas control valve body.
Contact your local building
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance company
of this heater as well.
If the flame becomes sooty, dark
orange in color, or extremely tall,
do not operate the heater. Call
your dealer and arrange for
proper servicing.
It is imperative that control
compartments, screens, or
circulating air passageways of
the heater be kept clean and
free of obstructions. These
areas provide the air necessary
for safe operation.
Do not operate the heater if it is
not operating properly in any
fashion or if you are uncertain.
Call your dealer for a full
explanation of your heater and
what to expect.
Do not store or use gasoline or
other flammable liquids in the
vicinity of this heater.
© Travis Industries
3/16/18 - 1452
Do not operate if any portion of
the heater was submerged in
water or if any corrosion occurs.
Immediately call a qualified
service technician to inspect the
appliance and to replace any part
of the control system and any
gas control that has been under
water.
PB Lin MV Operation
Safety Precautions
Do not place clothing or other
flammable items on or near the
heater. Because this heater can
be controlled by a thermostat
there is a possibility of the
heater turning on and igniting
any items placed on or near it.
© Travis Industries
5
Light the heater using the built-in
igniter. Do not use matches or
any other external device to light
your heater.
Allow the heater to cool before
carrying out any maintenance or
cleaning.
The viewing glass should be
opened only for conducting
service. Do not operate with
cracked, broken, or removed
glass.
Any safety screen or guard
removed for servicing must be
replaced prior to operating the
heater.
Never remove, replace, modify or
substitute any part of the heater
unless instructions are given in
this manual. All other work must
be done by a trained technician.
Don't modify or replace orifices.
Operate the heater according to
the instructions included in this
manual.
If the main burners do not start
correctly turn the gas off at the
gas control valve and call your
dealer for service.
Instruct everyone in the house
how to shut gas off to the
appliance and at the gas main
shutoff valve. The gas main
shutoff valve is usually next to
the gas meter or propane tank
and requires a wrench to shut off.
This unit is not for use with solid
fuel
Do not place anything inside the
firebox (except the crushed
glass).
If any component becomes
damaged, replace with Travis
Industries components.
Do not throw this manual away.
This manual has important
operating and maintenance
instructions that you will need at
a later time. Always follow the
instructions in this manual.
Children and adults should be
alerted to the hazards of high
surface temperature and should
stay away to avoid burns or
clothing ignition. Young children
should be supervised when they
are in the same room as the
heater.
Travis Industries, Inc. grants no
warranty, implied or stated, for
the installation or maintenance of
your heater, and assumes no
responsibility of any
consequential damage(s).
3/16/18 - 1452
PB Lin MV Operation
6
Operation
Before You Begin
•
Read this entire manual before you use your new fireplace (especially the section "Safety
Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily
injury, or even death.
Location of Controls
There is a door on the lower portion of the screen assembly to provide access to the manual controls on
the fireplace. The door is held closed by two magnets. Open the door by gently pulling outward on the
upper portion of the lower trim.
On/Off Switch
Pilot Igniter
Gas Control Knob
Flame Adjust Knob
Optional Remote Receiver
Optional Blower Knob
© Travis Industries
This control is used to turn the heater on and off.
The pilot igniter is used only to start the pilot. When pressed, it sends an
electrical charge to the pilot assembly. This creates a blue spark directly
next to the pilot, igniting the pilot flame.
This knob is used to control gas to the heater and for starting the pilot. There
are three positions, ON, OFF, & PILOT. The pointer to the left of the knob
indicates the position this knob is in.
This knob controls the flame height from low ("LO") to high ("HI"). The
pointer above the knob points to the position this knob is in.
The receiver is used in conjunction with the optional remote thermostat. It is
used to control the remote and replaces the on/off switch for direct operation.
This knob controls the speed of the internal convection blower that pushes
the heated air into the room.
3/16/18 - 1452
PB Lin MV Operation
Operation
7
Starting the Pilot
Remove the glass frame before starting the pilot.
The pilot flame is required to ignite the main
burners (it also plays a safety role). It should
be left on once lit. It will stay lit unless the gas
control valve is turned to "OFF". However, the
pilot will go out if the gas is shut off, the
propane tank runs out (or low) or if the stove
malfunctions. If the pilot turns off frequently,
call your dealer for information. To start the
pilot follow the directions below:
WARNING:
When lighting or re-lighting the pilot, the
glass must be removed (see page 10).
a Remove the glass (see page 10 for details).
b Push the gas control knob in slightly and
turn it to the "OFF" position. The knob will
not turn from "ON" to "OFF" unless the knob
is depressed slightly. Wait five minutes to
let any gas that may have accumulated
inside the firebox escape. If you smell
leaking gas, follow the directions on the
cover "IF YOU SMELL GAS".
c Turn the gas control knob to the "PILOT"
position and press the knob in, this will allow
gas to flow to the pilot light. Press the
button on the pilot igniter repeatedly until
you see the pilot light.
WARNING:
If the pilot does not light after 15 seconds,
release the knob and call your dealer for
service. Do not attempt to light pilot until
service has been performed.
d
Keep the gas control knob depressed for 30
seconds once it is lit.
e
Release the gas control knob. If the pilot
goes out, repeat step C. If the pilot refuses
to stay lit, call your dealer for service. With
the pilot lit, proceed to step “f”.
f
Replace the glass.
g
Turn the gas control knob counter-clockwise
to "ON". The pilot is now lit and the heater
can be turned on and off.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
8
Operation
Starting the Heater for the First Time
•
Burn the heater at a low setting with the blower off for an extended period (up to 48 hours). This will
cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This
is normal. We recommend opening a window to vent the room.
•
Condensation may appear on the glass each time you start the heater - this is normal.
•
Blue Flames will occur on the heater when it first comes on. After fifteen minutes the flames will turn
a more realistic yellow and orange color.
Turning the Heater On and Off
•
Do not place any combustible items on top of or directly in front of the heater, even temporarily. The
optional thermostat may start the heater causing a combustible item to ignite.
•
If the heater turns on and off frequently while using the thermostat, you may want to adjust the flame
height down until it produces just enough heat needed.
Adjusting the Flame Height
•
Your heater has an adjustable flame to tailor the look and heat output to your specific needs. It is
adjusted by turning the middle dial on the gas control valve.
Adjusting the Blower Speed (Optional)
The optional blower helps transfer heat from the heater into the room. It will not turn on until the heater is
up to temperature (approximately 10 minutes after starting). See the illustration below for instructions on
adjusting the blower speed.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
Operation
9
Normal Operating Odors
This appliance has several areas that reach high temperatures. Dust or other particles on these areas
may burn and create an odor. This is normal during start-up. You may notice the smell is more acute if
the appliance was left idle for a long period.
Power Outages
The heater will work if household current (AC power) is disconnected.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
10
Maintenance
Glass Frame Removal and Installation
A barrier designed to reduce the risk of burns from the hot viewing glass is provided
with this appliance and shall be installed for the protection of children and other at-risk
individuals.
If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s
barrier for this appliance.
The appliance must be completely cool before removing the glass.
Do not strike or slam the glass.
Warning: Do not operate appliance with the glass front removed, cracked or broken.
Replacement of the glass should be done by a licensed or qualified service person.
•
Remove the screen-trim assembly by lifting the assembly up slightly and tilting it toward you. The
mounting hooks on the back of the assembly will disengage the fireplace. Set the assembly aside for
reinstallation.
NOTE: Opening the access door on the front of the assembly allows for an easy location to get a secure grip
on the assembly for removal
Bottom Corner
Top Corner
Top hook engages
this slot in bracket
Bottom hook
engages this slot in
bracket
Replacement Barrier Part #
© Travis Industries
42 ProBuilder
250-04494
54 ProBuilder
270-01993
72 ProBuilder
270-01991
3/16/18 - 1452
PB Lin MV Operation
Maintenance
•
11
Remove the glass frame following the directions below.
NOTE: Make sure the glass frame is all the way in place – It should be parallel with the front of the
fireplace when installed.
Replacement Glass Frame Part #
© Travis Industries
42 ProBuilder
250-04491
54 ProBuilder
270-01994
72 ProBuilder
270-01992
3/16/18 - 1452
PB Lin MV Operation
12
Maintenance
The latch can come loose from glass frame anchor. This occurs when it is turned 1/4 turn when it
is disengaged. Follow the directions below to re-install the latch if it becomes loose.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
Maintenance
13
Crushed Glass Installation
Do not allow the crushed glass to block the air slots or to become too thick (maximum 1
layer deep on the burner). Failure to properly install glass may lead to sooting and
improper burning.
If converting to LP (propane), convert the appliance prior to placing the crushed glass.
Install the crushed glass on the glass tray following the directions below.
42 ProBuilder
54 ProBuilder
72 ProBuilder
1
Quantity of Crushed Glass
5 lbs. (2.3 Kg)
6 lbs. (2.7 Kg)
8 lbs. (3.6 Kg)
Spread and even layer of crushed glass over the media tray and burner. The glass must be only 1
layer thick on the burner but can be 2 layers thick on the media tray. Make sure no glass is in the
pilot area indicated in the picture below.
No glass in
this area.
Make sure the rear and end air channels are free of crushed glass. Use a screwdriver to clear this area.
Make sure the glass is only 1 layer deep on the burner.
Only one layer
thick on burner
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
14
Maintenance
Maintaining Your Heater's Appearance
The appliance must be completely cool prior to conducting service.
Cleaning The Glass
The glass may be cleaned with a nonabrasive cleaner. To clean the inside of
the glass, simply remove the glass frame,
place it on a non-scratching surface, and
clean the surface.
Cleaning the Fireplace
Use a duster to remove dust from the visible portions of the fireplace. Contact your dealer if you wish to
re-paint any surfaces. Heat-resistant stove-paint (with instructions) is available from your dealer.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
Maintenance
15
Yearly Service Procedure
•
1.
2.
3.
4.
5.
6.
7.
8.
Failure to inspect and maintain the heater may lead to improper combustion and a potentially dangerous
situation. We recommend the following procedures be done by a qualified technician.
Check the pilot flame. It should touch approximately 3/8" of the top of the flame sensor. If it does not, contact
your dealer for service.
Shut off gas to the heater and let it cool for 15 minutes. Remove the glass (see page 10). Glass may be
cleaned with glass cleaner and a soft cloth (do not use abrasive cleaners).
Remove the media (see the instructions included with your media kit). If severely deteriorated, replace. Check
the media for sooting. A small amount of soot along the bottom of the media is normal. If excessive sooting is
found, the heater will require adjustment. Contact your dealer.
Inspect the burner and remove any debris.
•
Make sure the burner is not warped, cracked, or damaged.
•
Check the firebox and area around the pilot to make sure there is no warping or damage.
•
If any problem is found, discontinue use and contact your dealer for service.
Replace the media. Clean and replace the glass. If the glass is damaged, replace. Make sure the gasket along
the perimeter of the glass contacts the face of the firebox and forms an air-tight seal. If it does not, re-align or
replace the gasket to insure an air-tight seal.
Inspect the area behind the access door. Clean if necessary.
Check the gas control valve and the gas lines. If damage is found,
discontinue use and contact your dealer for service. Clean the air
channels, ducts, and blower (if applicable).
Start the main burner. Inspect the main burner and pilot flame.
After 15 minutes the flames should be orange/yellow and not touch
the top of the firebox. If the pilot or main burners do not burn
correctly, contact your dealer for service. Monitor blower operation.
Remove any debris or vegetation near the vent termination. Contact
your dealer if any sooting or deterioration is found near the vent
termination. Venting system should be examined by a qualified
agency.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
16
Maintenance
Troubleshooting Table
Problem:
Pilot Will Not Light
Main Burners Will
Not Start
Optional Remote
Control Does Not
Work
Heater Will Not
Possible Cause:
Don't Call for Service
Until You:
A gas shut off valve is turned off
The gas control knob isn't turned to "PILOT"
The valve control knob isn't pushed in
The igniter wasn't pressed repeatedly
No Propane in Tank
Check all gas shut off valves
See "Starting the Pilot Light" Step C
See "Starting the Pilot Light" Step C
See "Starting the Pilot Light" Step C
Check Tank Level
The pilot light has gone out
The gas control valve is turned to "PILOT" or "OFF"
The ON/OFF switch is turned to "OFF"
The remote control is not working correctly
The thermostat is disconnected or set too low
See "Starting the Pilot Light"
See "Starting the Pilot Light"
Turn the ON/OFF switch to "ON"
See the remote control instructions
See "Thermostat Operation"
The pilot light has gone out
The gas control valve is turned to "PILOT" or "OFF"
The ON/OFF switch is turned to "OFF"
The remote is too far away from the heater
The remote control receiver is turned "Off"
Remote or receiver batteries are dead
See "Starting the Pilot Light"
See "Starting the Pilot Light"
Turn the ON/OFF switch to "ON"
Use the remote closer to the heater
See the remote control instructions
See the remote control instructions
The heater is not up to temperature
This is normal – allow 5 to 20 minutes for
heater to reach operating temperature.
The heater is not up to temperature
The heater is not getting electricity
The blower is set to off
The blower will turn on once the heater is
up to temperature (5 to 20 minutes).
Check the breaker switch.
Check the blower knob.
The gas supply has been shut off
Keep the gas supply turned on
The heater has just been started
This is normal - see "Starting the Heater
for the First Time"
Adjust Air Shutter - contact your dealer
Distribute Heat
Optional Blower
Does Not Turn On
Pilot Goes Out
Intermittently
Flames Are Too
Blue
Flames Are Too
Improper air shutter adjustment
The flame height may be turned too low
Turn the flame height to "HI" See "Adjusting the Flame Height"
The logs or coals are placed incorrectly
Improper air shutter adjustment
See "Log Set Installation"
Adjust Air Shutter - contact your dealer
Short (Under 6")
Thin Layer of Soot
Covers the Glass
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
Maintenance
17
Replacement Parts List
Caution:
Use only Travis Industries replacement parts. Do not use substitute materials.
Warning:
Do not operate appliance with the glass front removed, cracked, or broken. Replacement of
the glass should be done by a licensed or qualified service person.
GLASS w/FRAME (42 ProBuilder)
250-04491
GLASS w/FRAME (54 ProBuilder)
270-01994
GLASS w/FRAME (72 ProBuilder)
270-01992
SCREEN BARRIER, FRONT (42 ProBuilder)
250-01989
SCREEN BARRIER, FRONT (54 ProBuilder)
270-01993
SCREEN BARRIER, FRONT (72 ProBuilder)
270-01991
PILOT ASS'Y, 3-WAY PSE
250-04481
VALVE, NG w/MANUAL H/L
250-04377
VALVE REGULATOR, LP MAN HI-LO
250-00415
Contact your local Travis Industries Dealer for Replacement Parts
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
18
Maintenance
Wiring Diagram
Caution:
Label all wires prior to disconnection when servicing controls. Wiring errors can cause
improper and dangerous operation.
Optional Blower Wiring
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
19
Safety Label
42 ProBuilder Safety Label
The safety (listing) label is attached to the operating tag (chained to the heater near the gas control
valve). A copy is shown below
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
20
Safety Label
54 ProBuilder Safety Label
The safety (listing) label is attached to the operating tag (chained to the heater near the gas control
valve). A copy is shown below
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
21
Safety Label
72 ProBuilder Safety Label
The safety (listing) label is attached to the operating tag (chained to the heater near the gas control
valve). A copy is shown below
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
22
Index
Register your TRAVIS INDUSTRIES, INC. Limited 7 Year Warranty online at traviswarranty.com, or complete the enclosed Warranty card and mail it within ten (10)
days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants
this gas appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to the original
purchaser from the date of purchase as follows:
Check with your dealer in advance for any costs to you when arranging a warranty call.
Mileage or service charges are not covered by this warranty. This charge can vary from store to store.
Years 1 & 2
Parts & Labor
Component
Years 3 Through 5
Parts & Labor
Years 6 & 7
Parts Only
Burner Assembly
Burner Pan Assembly, Air Shutter Assembly, Main Burner Orifice
Electrical Assembly (within heater structure):
Wiring harness, snap discs, rheostat speed control
Gas Control Assembly
Adjustable control valve, fireplace controller, pilot assembly and pilot wiring
Glass
Glass (breakage from thermal shock)
Gold, Nickel & Copper Plating
Face & Door (see “Conditions and Exclusions” # 9)
Accessories
Firebacks, Power Heat Ducts, Andirons, etc…
One-Way Freight Allowance
One-way freight allowance on pre-authorized repair done at factory is covered.
Convection Heat Exchanger
Convection heat exchanger assembly
Firebox Assembly
Adjustable Air Restrictor, Pressure Relief Mechanisms, Glass Attachment Mechanism
EXCLUDED COMPONENTS:
Paint, Gasketing, and Accent Light Bulbs
CONDITIONS & EXCLUSIONS
1. This new gas appliance must be installed by a qualified gas appliance technician. It must be installed, operated, and maintained at all times in accordance with the instructions in the Owner’s
Manual. Any alteration, willful abuse, accident, neglect, or misuse of the product shall nullify this warranty.
2. This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized TRAVIS dealer.
3. Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and, therefore, not covered under warranty. The installer must
ensure the appliance is burning as per the rating tag at the time of installation. Over-firing (operation above the listed BTU rate) of this appliance can cause serious damage and will nullify this
warranty.
4. The warranty, as outlined within this document, does not apply to the chimney components or other Non-Travis accessories used in conjunction with the installation of this product. If in doubt as to
the extent of this warranty, contact your authorized TRAVIS retailer before installation.
5. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees, buildings, roof tops, wind, hills or mountains or negative pressure or
other influences from mechanical systems such as furnaces, fans, clothes dryers, etc.
6. This Warranty is void if:
a. The unit has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.
b. The unit is subject to submersion in water or prolonged periods of dampness or condensation.
c. Any damage to the unit, combustion chamber, heat exchanger or other components due to water, or weather damage which is the result of, but not limited to, improper chimney/venting installation.
7. Exclusions to this 7 Year Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation, alteration or adjustment of the manufacturer's
settings of components, lack of proper and regular maintenance, damage incurred while the appliance is in transit, alteration, or act of God.
8. This 7 Year warranty excludes damage caused by normal wear and tear, such as paint discoloration or chipping, worn or torn gasketing, corroded or cracked logs, embers, etc. Also excluded is
damage to the unit caused by abuse, improper installation, modification of the unit, drilling of the orifices, or the use of fuel other than that for which the unit is configured. Units are shipped for
natural gas and must be converted to propane using the included conversion kit. Confirm fuel configuration with your installer.
9. Damage to gold or nickel surfaces caused by fingerprints, scratches, melted items, or other external sources left on the gold or nickel from the use of cleaners other than denatured alcohol is not
covered in this warranty.
10. TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials. Incidental or consequential damages are not covered by
this warranty. In some states, the exclusion of incidental or consequential damage may not apply.
11. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the gas appliance without the express written permission of TRAVIS
INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of approval.
12. Any statement or representation of TRAVIS products and their performance contained in TRAVIS advertising, packaging literature, or printed material is not part of this 7 year warranty.
13. This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way. If the appliance is used for commercial purposes, it is excluded from this warranty.
14. No dealer, distributor, or similar person has the authority to represent or warrant TRAVIS products beyond the terms contained within this warranty. TRAVIS INDUSTRIES, INC. assumes no liability
for such warranties or representations.
15. Travis Industries will not cover the cost of the removal or re-installation of hearths, facing, mantels, venting or other components.
16. If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.
17. THIS 7 YEAR WARRANTY IS THE ONLY WARRANTY SUPPLIED BY TRAVIS INDUSTRIES, INC., THE MANUFACTURER OF THE APPLIANCE. ALL OTHER WARRANTIES, WHETHER
EXPRESS OR IMPLIED, ARE HEREBY EXPRESSLY DISCLAIMED AND PURCHASER’S RECOURSE IS EXPRESSLY LIMITED TO THE WARRANTIES SET FORTH HEREIN.
IF WARRANTY SERVICE IS NEEDED:
1. If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your TRAVIS dealer WITHIN 30 DAYS, giving them proof of purchase, the purchase date, and the
model name and serial number.
2. Travis Industries has the option of either repairing or replacing the defective component.
3. If your dealer is unable to repair your appliance’s defect, he may process a warranty claim through TRAVIS INDUSTRIES, INC., including the name of the dealership where you purchased the
appliance, a copy of your receipt showing the date of the appliance’s purchase, and the serial number on your appliance. At that time, you may be asked to ship your appliance, freight charges
prepaid, to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your TRAVIS appliance if it is found to be defective in material or
workmanship within the time frame stated within this 7 year warranty. TRAVIS INDUSTRIES, INC. will return your appliance, freight charges (years 1 to 5) prepaid by TRAVIS INDUSTRIES, INC.,
to your regional distributor, or dealership.
4.
Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty. This charge can vary from store to store.
© Travis Industries
3/16/18 - 1452
PB Lin MV Operation
Limited 7 Year Warranty
© Travis Industries
3/16/18 - 1452
23
PB Lin MV Operation
24
Index
Index
Before You Begin ............................................... 6
Crushed Glass Installation ............................... 13
Features ............................................................. 3
Glass Frame Removal and Installation ............ 10
Heating Specifications ........................................ 3
Important Information ......................................... 2
Installation Warnings .......................................... 2
Location of Controls ........................................... 6
© Travis Industries
Maintaining Your Heater's Appearance ........... 14
Normal Operating Odors .................................... 9
Power Outages .................................................. 9
Replacement Parts List .................................... 17
Starting the Heater for the First Time ................ 8
Starting the Pilot................................................. 7
Wiring Diagram ................................................ 17
Yearly Service Procedure ................................ 15
3/16/18 - 1452
PB Lin MV Operation
Download PDF