User Manual
7" TFT LCD Display Portable DVD Player
with Digital TV Tuner, AM/FM Stereo Radio
& USB/SD/MMC Inputs
Model: NDL-400
Before attempting to connect, operate or adjust this player, please read these instructions completely.
And then put this manual in a safe place for future reference.
1
2
Illustration of the Controls/Jacks On the Main Unit
7
1
3
2
21
5
4
7
6
24 26
22 23 25 32
15
9 11 13
8 10 12
17
16
14
18
19
20
27
28
29
30
1. VOLUME CONTROL
2. PHONES JACK
3. MIC JACK
4. TV/DVD BUTTON
5. CH+/UP BUTTON
6. CH-/DOWN BUTTON
7. LCD SCREEN (CD DOOR IS INSIDE)
8. STOP&DVD/SD/USB BUTTON
9. PLAY/PAUSE BUTTON
10. CD DOOR OPEN AREA
11. PREVIOUS/FR/LEFT BUTTON
12. NEXT/FF/RIGHT BUTTON
13. TV MENU BUTTON
14. TUNING CONTROL
15. AUX IN JACK
16. USB PORT
17. SD/MMC CARD SLOT
31
18. POWER INDICATOR
19. FM ST. INDICATOR
20. REMOTE SENSOR
21. BAND SWITCH
22. HANDLE
23. FM TELESCOPIC ANTENNA
24. VIDEO OUTPUT JACK
25. AUDIO LEFT JACK
26. AUDIO RIGHT JACK
27. AC SOCKET
28. DC JACK
29. FUNCTION SWITCH
30. BATTERY COMPARTMENT
31. AC VOLTAGE SELECTOR (FOR DUAL VOLTAGE
VERSION AND AT BOTTOM OF UNIT) (OPTIONAL)
32. TV ANT JACK
* Rating label is located at the bottom of the unit.
3
Remote control unit
Connecting to a stereo TV set
To power outlet
15
16
1
17
AC power cord
2
LR
18
3
To video input connector (yellow)
To audio input connectors (red, white)
4
Video/audio cable
5
19
6
7
20
21
8
22
9
23
10
11
12
24
25
13
14
26
27
1. SCREEN OFF/ON button
2. MUTE button
3. P MODE button
4. GUIDE button
5. TV MENU button
6. REPEAT button
7. PLAY button
8. SUBTITLE button
9. AUDIO button
10. PAUSE/STEP button
11. ANGLE/PROGRAM
button
12. ZOOM/SLOW button
13. TV/DVD button
Connecting the Aerial to the player
Aerial input
14. MTS button
15. DISPLAY button
16. SETUP button
17. P/N button
18. NUMERIC buttons
19. DVD MENU button
20. STOP&DVD/USB/SD button
21. OK button
22. NAVIGATION buttons
23. TITLE button
24. NEXT/F.FWD button
25. PREV/ F.BWD button
26. SEARCH button
27. CC button
CABLE
Optional
12V DC JACK
DC 12V JACK (Center is positive) in 1.7mm (inner diameter)
type.
To connect external power source of an AC adaptor or a car
adaptor.
Please make sure that the DC voltage is 12V and with correct
polarity as per below.
Basic connection
— It is recommended to be connected to a multi-system TV.
— Ensure that this player and other equipment to be connected
to the unit are in the standby or off mode and disconnect the
AC power cords before commencing connection.
— Do not block ventilation holes of any piece of the equipment
and arrange them so that air can circulate freely.
— Read through the instructions before connecting other
equipment.
— Ensure that you observe the color coding when connecting
audio, video cables.
Center pin is positive
Note:
— During DVD play, the TV volume may be at a lower level
than during TV broadcasts, etc. If this is the case, adjust the
volume to the desired level.
— If the DVD/CD player is connected to the TV through a video
cassette recorder, the picture may not be played back
normally with some DVDs. If this is the case, do not connect
the player via the VCR.
4
Note: Inputting leading zero is not necessary. Some figure
inputs may be useless, because it's greater figure than total
title/chapter /track number on the disc.
Example: Track 3, press "3"
Track 12, press "+10" and then "2"
Track 21, press "+10" twice and then "1"
3. To start programmed playback, select PLAY on the menu;
pressing PROGRAM button again to exit programming.
4. To clear all items, select the <CLEAR> on the menu, and
then press ENTER button on remote control.
5. You can also cancel program mode by clearing all the items
in the program menu.
OPERATIONS
PREPARATION
Power on the TV set and select video input mode.
Power on the audio system which is connected to the player.
GET STARTED
1. Slide the FUNCTION SWITCH to TV/DVD position.
2. Lift CD cover to open the disc tray.
3. Place a disc onto the disc tray.
4. Close the disc tray and the playback starts automatically.
5. When a menu screen appears on the TV, move the navigation
buttons or press the numeric buttons to select a preferred track
number, then press OK button to start playback.
6. Slide the function switch to OFF position to turn off the unit.
ZOOM PLAY
Press ZOOM button continuously to zoom in the picture by 2, 3,
and 4 times, zoom out by 1/2, 1/3, 1/4 normal size.
Press this key once more when the picture is at 1/4 size to
return to the normal size display.
Scroll to view the enlarged picture using Navigation buttons.
ADJUST THE VOLUME
Turn VOLUME CONTROL to increase or reduce the volume.
SKIP AHEAD OR BACK
Press NEXT or PREV button once during play to skip a chapter
(DVD) or a track (CD) ahead or backwards.
ON SCREEN DISPLAY INFORMATION
When the player is in operation, press DISPLAY button
continuously on the remote control, the screen will
display parts of information (current disc type, title number,
chapter number, playtime, audio language, audio type, subtitle
language and multi angle, etc) in a sequence.
RAPID ADVANCE/REVERSE
During playback, press and hold F.FWD button or F. BWD
button several times to scan the disc forward or backward at
X2, X4, X8, X20 normal speed.
Press PLAY button to resume normal play.
CHANGING AUDIO SOUNDTRACK LANGUAGE(DVD DISC)
It is possible to change the audio soundtrack language to a
different language from the one selected at the initial settings
(This operation works only with discs on which multiple audio
soundtrack languages are recorded).
Press AUDIO button during DVD disc play, the sound track
language changes with the current sound track number shown
on the TV screen.
NOTE: When no soundtrack languages are recorded, pressing
this button will not work.
MUTE
During playback, press MUTE button to shut off the audio
output, press it again resume normal play.
STOP PLAYBACK
Press STOP button during playback to stop playback; the
player activates its resume function when STOP is pressed in
STOP mode; press PLAY button again, playback resumes at
the point it stopped previously; open the disc tray or press the
STOP button one more time to clear the resume function.
MULTI-ANGLE VIEWING (DVD ONLY)
Press and hold ANGLE button during playback to cycle the
angle available on the disc.
Note: only the DVDs shot with multi-angle scenes have this
function.
SLOW-MOTION PLAY (DVD)
Press SLOW button on the remote control during playback, the
disc will be played at 1/ 2 normal speed at first, each time this
button is pressed, the play speed becomes slower (down to 1/7
normal speed.)
Press PLAY button, normal play will resume.
CHANGING SUBTITLE LANGUAGE (DVD ONLY)
Press SUBTITLE button during playback, the subtitle language
shown on the screen will change as a response to each press;
When the desired language appears, release the button to view
the subtitle in that language.
Note: this function only works on the DVDs recorded with multilanguage subtitles.
REPEAT BUTTON
Press REPEAT button during play, it will repeat play one
chapter/title or repeat all (for DVD disc), or repeat play a track
or all tracks (CD), or repeat the specified points (A-B).
RETURN TO MAIN MENU AND PLAY THE TITLE (DVD)
During playback, press DVD MENU button to return to main
menu. Press TITLE button to play the title.
SWITCH TV SYSTEM
During playback, press P/N button to switch TV system directly.
PAUSE/STEP PLAY
Press PAUSE/STEP button during playback to pause. during
pause mode, each time the PAUSE/STEP button is pressed,
the player will only play one frame; to resume normal play,
press PLAY button.
MP3/MPEG 4 PLAYBACK
1. Load the MP3/MPEG 4 disc onto the disc tray and the TV
screen will show all its folders after a few seconds.
2. Select the folder you want by the navigation buttons and then
ENTER button to confirm.
3. The files in this folder are displayed and select your
favourable song via navigation buttons and press ENTER
button to start playback.
4. Press NEXT and PREV button to select track directly.
5. Press REPEAT button change play mode.
SEARCH FOR PREFERRED SCENE
1. Press SEARCH button during play and highlight the item to
be played (Title, Chapter, or Chapter time) by navigation
buttons
2. Input the desired number or time via the numeric buttons.
3. Press OK button to confirm and the playback from the
located scene starts.
4. To exit search menu, press SEARCH button directly.
PROGRAM PLAY (UP TO 16 MEMORIES)
1. Press PROGRAM during playback to display the program
menu.
2. Select location(s) to be memorized via navigation buttons
and then enter desired Titles/Chapters numbers via numeric
buttons.
5
1. SYSTEM SETUP
KODAK PICTURE CD / JPEG CD PLAYBACK
Slide show of Kodak Picture CD after being loaded begins
automatically;
Folders of JPEG picture CD after being loaded are displayed
on the TV screen; use the navigation buttons to select the
desired folder and then press ENTER button to confirm.
The files in this folder are displayed and you can select your
favourable pictures using the up/down navigation buttons and
press ENTER button to start playback.
Preview of the picture will be displayed while you scroll across
the filenames.
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
TV TYPE
DEFAULT
EXIT SETUP
1.1 TV SYSTEM - it is used to select the TV mode.
Please select this option as per your TV set.
1.2 SCREEN SAVER- when the player is not used for several
minutes, a running DVD logo will move across the screen
to protect the screen.
Options: ON: the screen saver is enable.
OFF the screen saver is disable.
1.3 TV TYPE- it is used to select the TV scan mode, please set
as per your TV set.
Options: 4:3PS : Normal Pan & scan mode
4:3LB : normal Letter box mode
16:9 : 16:9 wide screen mode
1.4 DEFAULT - Reset to factory settings.
Options: RESTORE
KODAK PICTURE CD / JPEG CD OPERATIONS
1. PLAY MODES
Press REPEAT button during play to change the play modes.
During playback, press STOP to enter preview mode.
2. SKIP TO NEXT/PREVIOUS PICTURE
Press NEXT button to skip to the next picture or PREV button
to the previous picture..
3. PICTURE ROTATIONS
Press RIGHT and LEFT navigation buttons to rotate the picture
Clockwise and anti-clockwise respectively.
4. PICTURE FLIP AND TURN
Press UP navigation button to flip the picture up or down.
Press DOWN navigation button to turn the picture left or right.
5. PICTURE ZOOM IN/OUT
Press ZOOM button continuously ,the picture zooms in by 2, 3,
4 times or zooms out by 1/2, 1/3, 1/4 the original size.
Press this button once more when the picture getting 1/4 size
to return to the normal play.
If the picture is enlarged, you may use the navigation buttons to
view blocked parts of the picture.
6. SLIDE SHOW TRANSITION MODES
During slide show playback, press the PROGRAM button
cyclically to select one of the play modes to play.
2. LANGUAGE SETUP
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
MENU LANG
EXIT SETUP
EXTERNAL MEMORY MEDIA OPERATION (USB & SD/MMC
CARD)
Insert a USB data traveller into the USB port and slide the
FUNCTION SWITCH to the TV/DVD position;
Press and hold STOP button to select USB mode among disc,
USB and card via navigation buttons and press OK To confirm.
An icon of READ USB shows in the LCD and after the USB is
successfully detected and read, the screen will show folders
and tracks on the USB.
It will begin playback from track Number 1 automatically.
NOTE: The player can successfully play the music files with
USB 1.0 and USB 2.0 storage device.
OR
Insert an SD/MMC card into the card slot;
Press and hold STOP button to select CARD mode among
disc, USB and card via navigation buttons and press OK To
confirm. Then the player will enter into SD/MMC mode.
2.1 OSD LANGUAGE - It is used to select different On Screen
Display language for different user.
2.2 AUDIO LANG - select preferred audio language.(DVD
only, need disc software support)
2.3 SUBTITLE LANG- Select preferred subtitle language.
(DVD only, need disc software support)
2.4 MENU LANG - Select preferred disc menu language.
(DVD only, need disc software support)
3. VIDEO SETUP
VIDEO SETUP
BRIGHTNESS
CONTRAST
HUE
SATURATION
EXIT SETUP
INITIAL SETTINGS
Initial settings page is for you to make your preferred settings
up for your player. Once the initial settings are done they are
retained in the CPU of the player until otherwise modified.
3.1 BRIGHTNESS - to set the brightness for the display.
Options: 0/2/4/6/8/10/12
3.2 CONTRAST - to set the contrast effect for display.
Options: 0/2/4/6/8/10/12
3.3 HUE - to set the colour impression for display.
Options: -6/-4/-2/0/+2/+4/+6
3.4 SATURATION - to set the saturation level for display.
Options: 0/2/4/6/8/10/12
COMMON PROCEDURES FOR INITIAL SETTINGS
1. Press SETUP button.
2. Use the navigation buttons to select the item you want to
modify, press OK button to confirm, setting page with further
setting items displayed shows on the TV screen. Again use
navigation buttons to make changes. Press again OK
button to confirm modifications.
3. Use navigation buttons to switch to another setting on the
main setting page.
4. Press SETUP button to exit main setting page.
6
4. SPEAKER SETUP
TV OPERATIONS
GET STARTED
— Be sure the TV antenna is connected to the set properly.
— Power on the unit. Slide FUNCTION button to TV/DVD
position, and press TV/DVD button to switch to TV mode.
Note: It is recommendable to scan channels first for the first
time using or no channel broadcasts. Please follow the below
steps to scan channels:
1. Press TV MENU to enter the TV setup menu, then use
navigation buttons to select "AUTO SCAN" option,
2. Press NAVIGATION RIGHT button to access the submenu,
3. select the properly Cable system and enter the Start to Scan
option to begin auto scan for scanning channels.
SPEAKER SETUP
DOWNMIX
EXIT SETUP
4.1 DOWNMIX
Options: LT/RT- Left/Right mix mode
STEREO- Select this option if you don't have a 5.1
channels amplifier.
BASIC OPERATIONS
SEARCH A PROGRAM
— Press CH +/- button on the unit or navigation up/down
button on the remote once, the channel number changes. A
desired channel can be reached using these two keys.
— NUMERIC button on the remote can facilitate you to select a
specific channel. If the channel number exceeds 10, input
first digital unit, then another digital unit;
— Note: this receiver can store the channels from 2~69, and
the maximum of each channel has 8 programs. To select the
desired programs by using - button and numeric buttons.
— Do as follows:
To select CH 13 NO. 2
Press 1 and 3, then press +10 and input 2.
Once the input is done, it will start broadcasting the selected
channel immediately.
RADIO OPERATION
TO PLAY THE RADIO
1. Slide the FUNCTION SWITCH to the RADIO position, the
POWER Indicator will light up.
2. Select the desired band with the BAND switch.
3. Tune to the desired station by rotating the TUNING control
(Move the control back and forth until you get the strongest
clearest sound).
4. The built-in AM antenna and external FM TELESCOPIC
ANTENNA are directional.
= When receiving an FM broadcast, fully extend the
TELESCOPIC ANTENNA and position for the best
reception.
= For AM broadcasts, rotate the whole set until the best
reception is heard.
5. Adjust the volume level to a comfortable listening level.
6. To turn off the radio, slide the FUNCTION SWITCH to OFF
position.
NOTES:
= If a particular FM (STEREO) station is weak, or you hear
too much background noise, try moving the position of
the band selector switch to the FM(MONO) position. This
can often result in a much clearer reception.
= When the band selector switch is set to FM STEREO
and a stereo broadcast is being received, the FM
STEREO indicator the unit will be light.
ADJUST AUDIO OUTPUT LANGUAGE
During TV playback, press MTS button to adjust the audio
output language.
DISPLAY PROGRAM INFORMATION
Press DISPLAY button to display current program information
including current channel mode, resolution, current calender
and time, soundtrack mode.
SET CLOSED CAPTION
The CC button is used to set the closed caption mode. Press
CC button repeatedly to set the CC mode (Off/On/CC on mute).
MUTE
In TV mode, press MUTE button to shut off the audio output,
press it again resume normal play.
STEREO HEADPHONE JACK
A stereo headphone jack has been provided on the top of the unit
so that you can listen to the unit without disturbing others. To use
this jack, plug in the headphones/earphones (not included) and
adjust the VOLUME control to a comfortable listening level.
NOTE: When external headphones/earphones are connected,
the sound to the unit's main speakers will be muted.
SOUND MODE
During TV broadcasting, press AUDIO button repeatedly to
switch sound mode among personal, standard, movie and
music.
AUXILIARY IN
Your player can be used as a power amplifier to playback the
programs from portable radio, TV set or Mp3 player or
whatever provide this appliance is so designed that audio
signal may be produced through a LINE-OUT jack or the like.
Observe the following steps to connect the player to another
appliance:
1. Power the player on using the supplied AC Power Cord.
2. Slide the FUNCTION SWITCH to AUX position.
3. Connect the appliance into the player's AUX in jack with
supplied LINE-OUT cable of the appliance.
4. Power on the appliance and begin play.
At this time you will be able to hear the sound produced from
the programs the connected appliance is broadcasting.
PICTURE MODE
In TV play mode, press P MODE button on the remote several
times to select your desired picture mode (Personal, Standard,
Dynamic, Soft)
ELECTRONIC PROGRAM GUIDE
Use GUIDE button to check information of the program guide
for the past and future. The Information in the EPG depends on
your signal provider.
TV SETTING MENU
Press once TV MENU button the screen will pop up a setting
menu;
Use the NAVIGATION LEFT/RIGHT buttons to select among
the main setting options, then press NAVIGATION UP/DOWN
button to enter the sub menu, again use NAVIGATION
LEFT/RIGHT button to select the desired option or adjust and
press OK/ENTER Button to confirm the item to be set;
press TV MENU to go to previously menu or scroll to top the
main setting options. Use TV MENU button to exit the setup
menu.
MIC
The MIC jack works in disc, USB and card mode. If you want to
use the microphone for singing or speaking, please connect it
to MIC jack.
7
Picture Mode
Contrast
Brightness
Sharpness
Tint
Color
UP/DOWN
62
53
50
0
60
MENU:EXIT
ADJUST
UP/DOWN
UP/DOWN
English
MENU:EXIT
UP/DOWN
Balance: it is used to adjust the balance effect according to your
own favorite.
Audio language: it is used to select the desired audio output
language.
OSD Duration
Sleep Timer
Time Zone
Daylight Saving Time
Clock
UP/DOWN
ADJUST
ADJUST
Antenna
Auto Scan
Show/Hide
Channel No.
Channel Label
0
ADJUST
Normal
Wide
MENU:EXIT
Menu Language: it is used to change menu language.
Color mode: it is used to change the color mode of screen.
Zoom Mode: it is used to select the display type.
Closed Caption: it is used to select the broadcasting program
provides closed caption. There are three options as below:
CC mode: use to select on, CC on Mute, off.
Basic Selection: select among from CC1, Cc2, CC3,
CC4,Text1, Text2, Text3 and Text4.
Advance Selection: service 1, Service 2, Service 3, Service 4,
Service 5, Service 6.
Restore Default: select this option to restore the factory setting.
Picture mode: it is used to select the desired picture mode.
Contrast: it is used to adjust the contrast effect according to
your own favorite.
Brightness: it is used to adjust the brightness effect according
to your own favorite.
Sharpness: it is used to adjust the sharpness according to your
own favorite.
Tint: it is used to adjust the tint effect according to your own
favorite.
Color: it is used to adjust the color according to your own
favorite.
Balance
Audio Language
English
Menu Language
Color Mode
Zoom Mode
Closed Caption
Restore Default
Personal
Air
ADJUST
MENU:EXIT
Antenna: it is used to select the Antenna type CATV or air.
Auto Scan: use this function to auto scanning and stored tuned
channels. Select auto scan option, then press NAVIGATION
RIGHT button to access the submenu, select the desired Cable
system and then enter the Start to Scan option to begin auto
scan.
Show/Hide: it is used to show or hide the programs according to
your own favorite.
Channel No.: Select the desired program from this option.
Channel Label: it is used to edit the name of the selected
program (Use up or down button to input symbol or letter as
desired, and press left or right button to enter the previous or
next item).
60 Sec
Off
Central
Off
----/--/-- --/-MENU:EXIT
OSD Duration: it is used to set the OSD display duration.
Sleep Timer: it is used to set the sleep timer to auto power off
the set.
Time Zone: it is used to select time zone from different region.
Daylight Saving time: it is used to advance one hour of the
daylight time in summer in order to save the power.
Clock: it is used to show code create date.
8
DISC HANDLING PRECAUTIONS
— Hold the disc by the edge so the surface will not be soiled with finger prints. Finger prints, dirt and scratches can
cause skipping and distortion.
— Do not write on the label side with a ball-point pen or other writing utensils.
— Do not apply benzine, thinner, and liquid that prevents against static electricity.
— Be careful not to drop or bend the disc.
— Install only one disc on the disc tray.
— Do not try to close the disc tray when the disc is not in stalled properly.
— Be sure to store the disc in its case when not in use.
TROUBLESHOOTING
If your DVD player does not seem to be functioning properly, check the items below before you contact an authorized service center
Symptom
Check
Power does not turn on or
suddenly turns off.
Make sure the AC cord is securely plugged into an AC outlet.
Remote control won't work
Check that the battery is inserted in the "+" and "-" direction properly.
Turn the power off and then back on.
The battery may be flat. Replace it with a new one.
Check that the signal transmission is directed at the remote control sensor on the DVD player.
Remove the obstacle between the remote controller and remote control sensor.
No picture or sound
Check that the A/V cables are securely connected.
Check that the disc is a DVD, DVD-RW or AUDIO CD.
Do not use a disc that has scratches or dirt.
Check that the label-side of the disc is facing up.
The pick-up lens of the DVD player may be dirty. Contact the service center for lens cleaning.
Check that the TV channel is set to VIDEO or AV if viewing with a TV.
No picture
No sound
No picture and sound
Distorted video or sound
Check that the LCD display is turned on.
Check that the display panel is open. If it is closed, audio will not be output to the speakers.
Check the volume setting. If set to zero, turn up volume level.
Check that the headphones are plugged into the PHONES socket.
Speakers cannot be used with the headphones.
Check that the batteries are properly installed and AC cord is properly connected.
Use a disc without scratches or dents.
CAUTION
— The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be
placed on the apparatus.
— Minimum distances 2.0cm around the apparatus for sufficient ventilation.
— The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths,
curtains, etc.
— No naked flame sources, such as lighted candles, should be placed on the apparatus.
— When the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily
operable.
— The use of apparatus is in tropical and/or moderate climates.
— Attention should be drawn to the environmental aspects of battery disposal.
9
Download PDF

advertising