www.blackanddecker.co.uk
KA2000
KA2500
A
B
C
D
E
F
2
(Original instructions)
ENGLISH
Intended use
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Safety instructions
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Your BLACK+DECKER sander has been designed for sanding wood, metal, plastics and painted surfaces. This tool is
intended for consumer use only.
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
3
ENGLISH
(Original instructions)
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
@
Warning! Additional safety warnings for sanders
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystanders. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
@
4
Warning! Take special care when sanding some
woods (e.g. beech, oak) and metal which may
produce toxic dust. Wear a dust mask specifically designed for protection against toxic dust
and fumes and ensure that persons within or
entering the work area are also protected.
@
@
u
u
Warning! Use this tool in a well ventilated area
when sanding ferrous metals. Do not operate
the tool near flammable liquids, gases or dust.
Sparks or hot particles from sanding or arcing
motor brushes may ignite combustible materials.
Warning! Do not sand magnesium! There is a
risk of fire or explosions.
Thoroughly remove all dust after sanding.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety when sanding paint
@
Warning! Observe the applicable regulations
for sanding paint. Pay special attention to the
following:
u Whenever possible, use a vacuum extractor for dust collection.
u Take special care when sanding paint which is possibly
lead based and may produce toxic dust:
u Do not let children or pregnant women enter the work
area.
u All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
and fumes.
u Do not eat, drink or smoke in the work area.
u Dispose of dust particles and any other removal debris
safely.
Safety of others
u This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
(Original instructions)
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
ENGLISH
Electrical safety
#
u
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Using an extension cable
u Always use an approved extension cable suitable for the
power input of this tool (see technical data). Before use,
inspect the extension cable for signs of damage, wear and
ageing. Replace the extension cable if damaged or defective. When using a cable reel, always unwind the cable
completely. Use of an extension cable not suitable for the
power input of the tool or which is damaged or defective
may result in a risk of fire and electric shock.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust collection canister
3. Sanding base
4. Finger attachment
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
5
(Original instructions)
ENGLISH
Accessories
The accessories supplied with your sander depend upon the
model that you have purchased. All the accessories listed
below are available in our Piranha® range. If you require an
accessory that is listed below but is not supplied with your
sander please visit our website at www.blackanddecker.eu.
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance of your tool. By using these accessories you will get the
very best from your tool.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding mesh (fig. A)
u
u
Hold the tool with the sanding base facing upwards.
Place the sanding mesh (5) onto the sanding base, making sure that the holes in the sheet line up with the holes
in the base.
Fitting sanding sheets (fig. B - Optional accessory)
Detach the two additional diamond-shaped tips (7) from
the sanding sheet (6).
The diamond-shaped tip (7) can be reversed and replaced
when worn.
u When the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
u When the whole tip is worn, remove it from the sanding
base and fit a new tip.
For optimal dust collection, ensure the correct type of sanding
paper is used.
u
Item
Description
Detail finger.
For small hard-to-reach areas. The detail finger can be
used for light sanding and for sanding into corners.
(Part Number - X32214-XJ)
240 grit sanding mesh.
For a fine finish for large detail sanding.
(Part Number - X39132-XJ)
120 grit sanding mesh.
For a medium finish for large detail sanding.
(Part Number - X39127-XJ)
80 grit sanding mesh.
For a coarse finish for large detail sanding.
(Part Number - X39122-XJ)
240 grit large detail sanding sheet with two
replacement tips.
For a fine finish for large detail sanding.
(Part Number - X31019-XJ)
120 grit large detail sanding sheet with two
replacement tips.
For a medium finish for large detail sanding.
The finger attachment is used for fine detail sanding.
u Remove the screw (9).
u Remove the diamond-shaped tip (8) from the sanding
base.
u Fit the finger attachment (4) onto the sanding base.
u Fit and tighten the screw.
u Fit the appropriate sanding sheet onto the finger attachment.
Fitting and removing the dust cassette (fig. D)
Slide the dust cassette (2) onto the tool and make sure
that it is securely located.
u To remove the dust casette, pull it to the rear and off the
tool.
u
Use
(Part Number - X31009-XJ)
Warning! Let the tool work at its own pace. Do not overload.
60 grit large detail sanding sheet with two
Switching on and off
replacement tips.
For a coarse finish for large detail sanding.
(Part Number - X31039-XJ)
120 grit detailed finger sanding sheet.
For a medium finish for detailed sanding.
(Part Number - X3277-XJ)
6
Finger attachment (fig. C)
To switch the tool on, slide the on/off switch (1) to the
forward position I.
u To switch the tool off, slide the on/off switch (1) to the back
position O.
u
(Original instructions)
Emptying the dust cassette (fig. D, E & F)
The dust cassette should be emptied every 10 minutes of use.
u While holding the tool, pull the dust cassette (2) off the
tool.
u Remove the cassette lid (10).
u Shake the lid (10) and dust cassette (2) to empty the
contents, the filter (11) inside the lid (10) can be cleaned
with a soft dry brush.
u Refit the lid (10) to the dust cassette (2).
u Refit the dust cassette (2).
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
ENGLISH
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Input voltage
Power input
Oscillations (no load)
Orbits (no load)
Sanding base surface
Weight
KA2000
KA2500
(Type 1)
(Type 1)
Vac
230
230
W
120
120
28,000
28,000
14,000
14,000
8161
8161
1
1
min-1
min
-1
mm
kg
2
LpA (sound pressure) 73 dB(A), Uncertainty (K) 3 dB(A)
LWA (sound power) 84 dB(A), Uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) 7.0 m/s2, uncertainty (K) 1.5 m/s2
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available for separate collection.
z
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
7
ENGLISH
(Original instructions)
EC declaration of conformity
MACHINERY DIRECTIVE
%
Sander - KA2000, KA2500
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-4
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact Black &
Decker at the following address or refer to the back of the
manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
R. Laverick
Engineering Manager
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
03/06/2014
8
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
BLACK+DECKER brand and our range of products is available at www.blackanddecker.co.uk
9
10
11
Australia
New Zealand
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. Fax 03-8720 5100
03-9727 5940
Black & Decker
5 Te Apunga Place
Mt Wellington
Aukland 1060
Tel. Fax +64 9 259 1133
+64 9 259 1122
United Kingdom &
Black & Decker
Tel. 01753 511234
Republic Of Ireland
210 Bath Road
Fax 01753 512365
www.blackanddecker.co.uk Slough, Berkshire SL1 3YD
emeaservice@sbdinc.com
90612701 REV-0
06/2014
Download PDF