GROUND FORCE® DRIFTER
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
CONTENTS
Safety Warnings............................................................................................... 1
Before You Begin.............................................................................................. 2
Assembly, Set-Up and Charging the Battery.................................................3-4
Pre-Ride Checklist and Usage........................................................................... 5
Repair and Maintenance...............................................................................6-8
Troubleshooting Guide...................................................................................... 9
Ground Force Drifter Parts.............................................................................. 10
Warranty and Customer Service Contact Information.................................... 14
SAFETY WARNINGS
Do not activate the throttle unless you are on the product and in a safe,
outdoor environment suitable for riding.
WARNING: Riding an electric product does present potential risks
and caution is required. Like any electric product, the Ground Force Drifter has
inherent hazards associated with its use (for example, falling off or riding it
into a hazardous situation). Like any electric product, the Ground Force Drifter
can and is intended to move and it is therefore, of course, possible to lose
control or otherwise get into dangerous situations. Both children and adults
responsible for supervising them must recognize that if such things occur, a
rider can be seriously injured or die, even when using safety equipment and
other precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
This product was manufactured for performance and durability but is not
impervious to damage. Jumping or other aggressive riding can overstress and
damage any product, including the Ground Force Drifter, and the rider assumes
all risks associated with high-stress activity.
Be careful and know your limitations. Risk of injury increases as the degree
of riding difficulty increases. The rider assumes all risk associated with
aggressive riding activities.
Maintain a hold on the steering wheel at all times.
WARNING: PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION IS NECESSARY: Because products, like the Ground Force
Drifter, can and do present potential hazards plainly associated with their use,
it is well recognized THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY
IN SELECTING ELECTRIC PRODUCTS APPROPRIATE TO THE AGE OF A CHILD,
OR PARENTAL SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF
VARIOUS AGES MAY HAVE ACCESS TO THE SAME ELECTRIC PRODUCTS, IS
IMPORTANT. Not every product is appropriate for every age or size of child,
and different age recommendations are found within this category of product
which are intended to reflect the nature of the hazards and the expected
mental or physical ability, or both, of a child to cope with the hazards.
Never carry passengers or allow more than one person at a time to ride the
electric product.
Never use near steps or swimming pools.
Do not allow hands, feet, hair, body parts, clothing, or similar articles to come
in contact with moving parts of the product, wheels, drive train, or chain while
the motor is running.
Do not touch the brakes or electric motor on your electric product when in use
as they can become very hot.
Never use headphones, a cell phone or text when riding.
The recommended minimum rider age is eight (8) and older. Any rider
unable to fit comfortably on the product should not attempt to ride it.
A parent’s decision to allow his or her child to ride this product should be
based on the child’s maturity, skill and ability to follow rules.
Never hitch a ride with another vehicle.
Do not ride the Ground Force Drifter in wet or icy weather and never immerse
the electric product in water, as the electrical and drive components could get
damaged by water or possibly create other unsafe conditions.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the product.
Wet, slick, bumpy, uneven or rough surfaces may increase risks. Do not ride
the electric product in mud, ice, puddles or water. Avoid excessive speeds that
can be associated with downhill rides. Never risk damaging surfaces such as
carpet or flooring by use of an electric product indoors.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions and to be able to
understand the hazards inherent in product use, should not use or be permitted
to use products inappropriate for their abilities. Persons with heart conditions,
head, back or neck ailments (or prior surgeries to these areas of the body), or
pregnant women, should be cautioned not to operate such products.
Do not ride at night or when visibility is limited.
PROPER RIDING ATTIRE
Always wear proper protective equipment such as an approved safety helmet
(with chin strap securely buckled). A helmet may be legally required by local
law or regulation in your area. Elbow pads and kneepads, a long-sleeved shirt,
long pants and gloves are recommended. Always wear athletic shoes (lace-up
shoes with rubber soles) and keep shoelaces tied and out of the way of the
wheels, motor and drive system. Never ride barefooted or in sandals.
DO NOT EXCEED THE WEIGHT LIMIT OF 140 lb (64 kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the Ground Force Drifter.
CHECK AND MAINTAIN PRODUCT CONDITIONS
Before use, check to confirm that any and all chain guards or other covers
and guards are in place and in serviceable condition. Check that the brake is
functioning properly, and that tires have sufficient tread remaining. The product
should be maintained and repaired in accordance with the manufacturer’s
specifications, using only the manufacturer’s authorized replacement parts, and
should not be modified from the manufacturer’s original design and configuration.
USING THE CHARGER
The charger supplied with the electric product should be regularly examined for
damage to the cord, plug, enclosure and other parts. In the event of such damage,
the product must not be charged until the charger has been repaired or replaced.
Use only with the recommended charger.
Use caution when charging.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may
affect the locations where the Ground Force Drifter may be used.
Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from product when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
product with damp cloth.
The Ground Force Drifter is meant to be used on private property and on
closed courses and not on public streets or sidewalks. Do not ride your electric
product in any areas where pedestrian or vehicle traffic is present.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS
INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE
CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.
1
BEFORE YOU BEGIN
Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect
the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping.
Because the Ground Force Drifter was 95 percent assembled and packed at the factory, there should not be any
problems, even if the box has a few scars or dents.
MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR
MAINTENANCE PROCEDURES.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult.
Allow up to 20 minutes for assembly, not including initial charge time.
Allow up to 12 hours for initial charge (see page 4 for charging information).
Brake Lever
WARNING:
DO NOT USE NON-RAZOR PARTS
WITH YOUR PRODUCT.
The Ground Force Drifter has
been built to certain Razor design
specifications. The original
equipment supplied at the time of
sale was selected on the basis of
its compatibility with the frame and
all other parts. Certain aftermarket
components may not be compatible
and will void the warranty.
Speed Control/Thumb Throttle
Product ID Locations:
Steering Wheel
See locations to the left
2.
Charger Port
On/Off Switch
Tie Rod
1.
1.
2.
3.
4.
Frame (Underneath Unit)
Battery Cover
Charger
Box - Side of UPC (Not Shown)
NOTICE: The lap/shoulder
belt arrangement supplied is not
intended for use in larger, faster
vehicles and is for “play” use only.
It is not an ASTM-approved safety
belt system and is not intended
to function as an approved lap/
shoulder/seat restraining device.
WARNING: Turn power
switch OFF before conducting any
maintenance procedures.
Charger
(Note: Charger design may
vary from one shown)
3.
Brake Adjustment
(Auxiliary)
Required Tool
Box Contents:
• Ground Force Drifter
• Charger
• Allen Wrench
• Owner’s Manual
• Seat Bolts (x4)
5 mm Allen Wrench
2
ASSEMBLY AND SET-UP
TURN POWER SWITCH OFF BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.
Attaching the Steering Wheel
Tool Required: 5 mm Allen Wrench
1 Using a 5 mm Allen wrench,
loosen the screw located in the
steering column.
2 Make sure the wires are not
tangled. Insert the steering wheel,
washer and screw into the steering
column as shown.
WARNING:
Failure to properly install and
tighten the screws, nuts and bolts
that affix the steering wheel and
seat can cause you to lose control
and crash.
3 Tighten screw securely using a
5 mm Allen wrench.
4 Using a 5 mm Allen wrench,
alternately tighten each of the bolts
on the steering wheel clamp. When
the bolts are properly tightened,
the gap between the clamp halves
should be even.
Attaching the Seat
WARNING:
The lap/shoulder belt arrangement
supplied with the Ground Force
Drifter is for “play” use only. It
is not an ASTM-approved safety
belt system and is not intended
to function as an approved lap/
shoulder/seat restraining device.
Tool required: 5 mm Allen Wrench
A
A
B
B
A
B
1 Position the seat over the frame
and align it with the holes in the
frame. Insert the four (4) seat bolts
and tighten securely.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
3
ASSEMBLY AND SET-UP
Attaching the Flag
1 Locate the hole located on the
top right side of the battery cover.
Insert the flag.
CHARGING THE BATTERY
Your Ground Force Drifter may not have a fully charged battery; therefore you must charge the battery prior to use.
• Initial charge time: 12 hours.
• To ensure long battery life, never store the product in
freezing or below freezing temperatures! Freezing will
• Recharge time: up to 12 hours, even if the light turns green.
permanently damage the battery.
Recommended maximum charging time is 24 hours.
• Run time: Up to 40 minutes of continuous ride time.
• Always charge the battery immediately after riding.
Run time may vary depending on riding conditions, rider
• Fully charge battery before storing for extended
weight, climate, and/or proper maintenance.
periods of time.
• Constant stopping and starting may shorten ride time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure the Ground Force Drifter’s power switch is
turned OFF when unit is not in use. If the power switch
is left on for an extended period of time, the battery may
reach a stage at which it will no longer hold a charge.
Charger
The charger supplied with the
Ground Force Drifter should be
regularly examined for damage to
the cord, plug, enclosure and other
parts. In the event of such damage,
the Ground Force Drifter must
not be charged until it has been
repaired or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
Note: If the charger gets warm
during regular use, this is a normal
response and is no cause for
concern. If your charger does not get
warm during use, it does not mean
that it is not working properly.
LED
Note: Make sure power is turned
OFF when unit is not in use. If
the power switch is left on for an
extended period of time, the battery
may reach a stage at which it will
no longer hold a charge.
WARNING:
Use ONLY with the recommended
charger. Batteries are only to be
charged under adult supervision.
The charger is not a toy. Always
disconnect the charger before wiping
down and/or cleaning the Ground
Force Drifter with a damp cloth.
1 Plug the charger plug into wall
2 Make sure the power switch
is in the OFF position. Plug the
charger into the charger port on the
Ground Force Drifter. The light on
the charger should turn red during
charging. The light will turn green
again when charging is complete.
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
4
Wall outlet - Green (stand by)
Wall outlet and unit - Red (charging)
Wall outlet and unit - Green (charged)
Note: Continue charging unit even if
light turns green prior to 12 hours.
WARNING: Failure to
recharge the battery at least once a
month may result in a battery that
will no longer accept a charge.
PRE-RIDE CHECKLIST
Brake
Hardware/Loose Parts
Check the brake for proper function. When you squeeze the
lever, the brake should provide positive braking action. When
you apply the brake with the speed control on, the brake cutoff switch will stop the motor.
Before every ride, check all parts, such as nuts, bolts, cables,
fasteners, etc., to ensure they are secure and assembled
correctly. There should not be any unusual rattles or sounds
from loose parts or broken components. If the unit is damaged,
do not ride. Reference “Safety Warnings” on page 1 of
this manual.
Wheels
Practice drift driving only in wide open areas clear from curbs,
parking blocks and other obstacles. Impacting the wheels
against any hard surface can damage the wheels. Wheels are
not covered under your limited warranty.
Safety Gear
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads and kneepads are recommended. Always
wear athletic shoes (lace-up shoes with rubber soles) and keep
shoelaces tied and out of the way of the wheels, motor and drive
system. NEVER RIDE BAREFOOTED OR IN SANDALS.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken
frames are rare, it is possible for an aggressive rider to run
into a curb or object, and wreck and bend or break a frame.
Get in the habit of inspecting your Ground Force Drifter on a
regular basis.
Laws and Regulations
Always check and obey any local laws or regulations.
USAGE
How to Start
How to Stop
Position your body in the seat and place one foot on each side of the
steering wheel. Fasten the lap/shoulder belt on. Turn power switch on,
place both hands on the steering wheel and apply the thumb tab throttle.
Note: Keep hands on the steering wheel and both feet inside the unit
when unit is in motion.
Release the thumb tab throttle and apply the brake lever until the unit comes
to a complete stop.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
5
REPAIR AND MAINTENANCE
Turn power switch OFF before conducting any maintenance procedures.
• Read the instructions
• Remove charger plug
• Turn the power switch OFF
• Secure the unit under repair
• Exercise caution around
exposed parts
• Contact Razor customer service
if unsure about any repair
or maintenance
Testing the Brake
WARNING: Practice in
an open area free from obstacles
until you are familiar with the brake
function. DO NOT RUN OVER ANY
OBJECT AS IT COULD DAMAGE THE
BRAKE OR DRIVETRAIN.
To use the brake, squeeze the lever to increase the pressure on the brake. The brake lever is fitted with a cable adjuster
to compensate for cable stretch and/or to fine-tune the lever movement to brake engagement. If brake is not engaging
properly, follow instructions for adjusting the brakes.
Adjusting the Brake
The brake lever is fitted with a cable adjuster to compensate for cable stretch and/or to fine tune the lever movement to
brake engagement.
1 To adjust the brake, thread the
adjuster in or out 1/4 to 1/2 turns
until the desired brake adjustment
is attained.
2 If the adjuster is threaded
outward and the brake still has
too much slack, use the auxiliary
adjuster at the rear brake for
additional adjustments.
Note: When properly adjusted,
the brake lever will have
approximately 3 mm of free play
before the brake engages.
Replacing the Wheels
Tools Required: 13 mm Allen Wrench (Front Wheels), 24 mm Allen Wrench (Rear Wheels)
Front and rear wheel installation and removal are the same.
Note: The brake lever contains a
safety switch to cut off power to the
motor when the brake is applied. In
an emergency, applying the brake
will always stop the product from
moving. Do not disable or replace
this lever with anything other than a
genuine Razor replacement part.
WARNING: Failure to
properly adjust and tighten the
screws, nuts and bolts that affix
the wheels can cause you to lose
control and crash.
Loosen
Tighten
1 To remove a wheel, remove the
self-locking nut (13 mm socket or
wrench required for front wheels,
24 mm for the rear wheels). Tap the
wheel to remove.
2
3 Rear Wheel Installation:
To replace a rear wheel, make sure
the key is properly seated in the
rear axle and aligned with the key in
the wheel. Position the wheel with
the Razor logo facing outward.
Install the washer and tighten the
self-locking nut securely.
Front Wheel Installation:
To replace a front wheel, make sure
the bearings are seated and the
center spacer is installed. Position
the wheel with the Razor logo
facing outward.
Install the washer and tighten the
self-locking nut securely.
6
Note: The Ground Force Drifter
wheels must be replaced
when worn down to the wear
indicator line.
Note: Practice drift riding only in
wide open areas clear from curbs,
parking blocks and other obstacles.
Impacting the wheels against
any hard surface can damage the
wheels. Wheels are not covered
under your limited warranty.
REPAIR AND MAINTENANCE
Turn power switch OFF before conducting any maintenance procedures. Before you begin, carefully turn
unit upside down for easier access.
Removing Rear Axle
Tools Required: 5 mm Allen Wrench, 10 mm Wrench, 24 mm Wrench
A
A
B
B
A B
1 Using a 5 mm Allen wrench,
2
Loosen the four (4) 5 mm bolts
(two on each side) on the battery
cover and remove cover.
3
4
Carefully turn unit over and
loosen the two (2) bolts next to the
brake cable.
5
6
7
8
loosen the four (4) seat bolts and
remove seat.
Using a 24 mm wrench, loosen
the lock nut on both rear wheels
and remove wheels. If necessary,
gently tap rear wheel with a rubber
mallet to help loosen wheel off the
rear axle.
Remove the eight (8) bolts
(four on each side) that attach the
brackets to the frame.
Using a 10 mm wrench, loosen
the nut that holds the brake cable
and pull cable outward.
Using a 5 mm Allen wrench,
loosen the four (4) bolts holding the
motor to the frame. Carefully lower
the motor and remove chain from
around the motor sprocket.
Remove the two (2) “C” clips
(one on each side). Remove the two
(2) brackets that hold the rear axle
in place and remove axle.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
7
REPAIR AND MAINTENANCE
Replacing the Chain
Note: Chain should be periodically
checked for grime build-up. If
necessary remove any dirt and/or
debris in and around the chain and
re-lubricate with WD-40®.
Master Link
Master Link:
Secure Clip
Connector Link
Drive Direction
1 Locate the master link on the
replacement chain and with a
flat head screwdriver carefully
disengage the clip from the chain
to remove the link plate and
connector link.
2 Wrap the chain around both
sprockets and tension idler. Insert
the connector link all the way
through the chain and fit the link
plate over the connector link.
3 Using a flat head screwdriver,
carefully re-attach the clip on to
the link plate. The clip must point in
the drive direction of chain rotation.
Self Adjusting Chain Tensioner
Note: Proper alignment of the
chain must be maintained. If the
chain is adjusted properly, but
is noisy or rough running, check
alignment of the sprockets. The
drive-shaft sprocket can be adjusted
slightly from side-to-side by
loosening the set screw. Note that a
key way maintains the drive position
to the shaft.
Motor shaft sprocket
Roller chain
Fixing bolt
Drive shaft sprocket
Battery Care and Disposal
Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery
life, carefully read the “Charging the Battery” section on page 4 of this owner’s manual.
Pb
Pb
Link Plate
CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED.
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not
dispose of a lead-acid battery in your regular household trash. The incineration, land filling or mixing of sealed lead-acid
batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state
approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is
prohibited by law to throw away lead-acid batteries in the municipal waste stream.
Charger
The charger supplied with the Ground Force Drifter should be regularly examined for damage to the cord, plug,
enclosure and other parts, and in the event of such damage, the product must not be charged until it has been repaired
or replaced.
Use ONLY with the recommended charger.
Wheels
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect
wheels for excess wear and adjust and replace drive train components as required.
Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners. For the
complete selection of replacement parts visit shop.razor.com.
Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is listed on the back of this manual.
8
WARNING: If a battery
leak develops, avoid contact
with leaking acid and place the
damaged battery in a plastic bag.
Refer to the disposal instructions
at left. If acid comes into contact
with skin or eyes, flush with cool
water for at least 15 minutes
and contact a physician.
WARNING: Battery posts,
terminals and related accessories
contain lead and lead compounds.
Wash your hands after handling.
TROUBLESHOOTING GUIDE
*Unit(s) should be turned OFF and fully charged prior to doing any Troubleshooting
NOTE: All troubleshooting steps should be performed by an adult only
Problem
Possible Cause
Solution
Product does not run.
Product is rolling backwards.
Throttle will not engage if the product is rolling backwards. Come to a
complete stop and then activate the throttle.
Undercharged battery.
Charge the battery. A new battery should have been charged for at least
12 hours before using the product for the first time and up to 12 hours after
each subsequent use.
Check all connectors. Make sure the charger connector is tightly plugged
into the charging port and that the charger is plugged into a functioning
wall outlet.
Charger is not working.
Contact Razor Customer Service to get replacement charger.
Product was running but
suddenly stopped.
Loose wires or connectors.
Check all wires and connectors to make sure they are tight.
Short run time.
Undercharged battery.
Charge the battery. A new battery should have been charged for at least
12 hours before using the product for the first time and up to 12 hours after
each subsequent use.
Battery is old and will not accept full
charge.
Even with proper care, a rechargeable battery does not last forever.
Average battery life is 1 to 2 years depending on product use and
conditions. Replace only with a Razor replacement battery.
Riding conditions are too stressful.
Use only on solid, flat, clean and dry surfaces such as pavement or level ground.
Product is overloaded.
Make sure you do not overload the product by allowing more than one
rider at one time, exceeding the maximum weight limit, going up too steep
a hill or towing objects behind the product.
Sometimes the product doesn’t
run, but other times it does.
Loose wires or connectors.
Check all wires connectors to make sure they are tight.
Motor or electrical switch damage.
Contact your local Razor authorized service center for diagnosis and repair.
Contact Razor customer service or visit www.razor.com.
Charger gets warm during use.
Normal response to charger use.
No action required. This is normal for some chargers and is no cause for
concern. If your charger does not get warm during use, it does not mean
that it is not working properly.
Product makes loud noises or
grinding sounds.
Chain is too dry.
Apply a lubricant such as 3 in 1™ or Tri-Flow™ to the chain.
Product runs sluggishly.
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.razor.com or call toll free +1 866 467 2967 to speak to a live Customer Service Representative
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
9
GROUND FORCE DRIFTER PARTS
Keep your Ground Force Drifter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
1.
2.
3.
4.
Steering Wheel
Thumb Tab Throttle
Brake Lever
Front Wheel (x2)
4-1 Nut, M8 Nylock Self Locking (x2)
4-2 Washer (x2)
4-3 Front Wheel Spacer (x2)
4-4 Bearing 608Zz 8X22 (x4)
4-5 Spring Washer
5. Spindle (Right/Left)
6. Protector (x2)
7. Steering Assembly
8. Axle Bearing 6904Zz 20X37 (x2)
9. Control Module
10. Motor (250W)
2
11. Chain
12. Rear Wheel (x2)
12-1Nut
12-2 Washer (x2)
12-3 Key Way A 5X5x20 (x2)
13. C-Clips (x2)
14. Rear Axle
15. Brake Drum
16. Sprocket
17. Chain Tensioner
18. Battery with Fuse (12V / 7Ah) (x2)
19. Flag
20. On/Off Switch
21. Charger Port
22. Battery Cover
23. Seat
23-1 Long Coupling Bolt (x2)
23-2 Short Coupling Bolt (x2)
24. Lap/Shoulder Belt
25. Steering Cover
25-1 Screw M5x16 (x2)
1
22
24
23-2
23-1
23
16
3
15
21
4-1
25-1
25
20
4-2
19
4
18
4-3
14
4-4
17
4-5
5
9
6
10
11
13
7
12-2
12-3
12
12-2
8
12-1
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
10
NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by Razor USA LLC, could void the user’s authority to operate the equipment.
WARRANTY
Razor Limited Warranty
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
The manufacturer warranties this product to be free of manufacturing defects
for a period of 90 days from date of purchase. This Limited Warranty does not
cover normal wear and tear, tires, tubes or cables, or any damage, failure or
loss caused by improper assembly, maintenance, storage or use of the Razor
Ground Force Drifter.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
UNITED STATES
EUROPE
ASIA
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
customersupport@razorusa.com
+44 (0) 120 267 2702
+81 50 7579 6622
info@razor-asia.com
DISTRIBUTED IN THE UK BY:
DISTRIBUTED IN AUSTRALIA BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
Funtastic Limited
Level 2, Tower 2, Chadstone Place
1341 Dandenong Road
Chadstone VIC 3148
Australia
+44 (0) 118 973 6222 Tel
+44 (0) 118 973 6220 Fax
sales@recreationltd.co.uk
+1 800 244 543
info@funtastic.com.au
Printed in China for Razor USA LLC.
Copyright © 2003-2016 Razor USA LLC. All rights reserved. Ground Force®, Razor® and the Razor
logo design are among the registered trademarks of Razor USA LLC in the United States and/or
select foreign countries. Ground Force Drifter is a trademark of Razor USA LLC.
14
US_160825
Download PDF