Extractor hood DWK068G61, DWK098G61, DWK068G21

Extractor hood
DWK068G61, DWK098G61, DWK068G21,
DWK098G21
[en] Instruction manual
Ú Table of contents
e[nuoIrs]ctimanul
Important safety information.....................................................3
Environmental protection ..........................................................5
Environmentally-friendly disposal.....................................................5
Operating modes........................................................................5
Exhaust air mode ................................................................................5
Circulating-air mode ...........................................................................5
Operating the appliance ............................................................6
Setting the fan .....................................................................................6
Intensive setting ..................................................................................6
Interval ventilation ...............................................................................6
Fan run-on time ...................................................................................6
Lighting .................................................................................................6
Saturation display ...............................................................................6
Cleaning protection ............................................................................7
Cleaning and maintenance........................................................ 7
Trouble shooting ........................................................................ 9
After-sales service ..................................................................... 9
Accessories for circulated air mode.......................................10
Produktinfo
Additional information on products, accessories, replacement
parts and services can be found at www.bosch-home.com and
in the online shop www.bosch-eshop.com
: Important safety information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for
future use or for subsequent owners.
The appliance can only be used safely if it
is correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly
at its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside.
Do not leave the appliance unattended
during operation. The manufacturer is not
liable for damage which is caused by
improper use or incorrect operation.
This appliance may be used by children
over the age of 8 years old and by persons
with reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with, on, or around
the appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old
at a safe distance from the appliance and
power cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance
if it has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
Danger of suffocation!
Packaging material is dangerous to
children. Never allow children to play with
packaging material.
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as room
air-dependent heat-producing appliance is
being operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters
or water heaters) obtain combustion air
from the room in which they are installed
and discharge the exhaust gases into the
open air through an exhaust gas system
(e.g. a chimney).
3
In combination with an activated vapour
extractor hood, room air is extracted from
the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough
fresh air is supplied. Toxic gases from the
chimney or the extraction shaft are sucked
back into the living space.
■ Adequate incoming air must therefore
always be ensured.
■ An incoming/exhaust air wall box alone
will not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for
combustion is able to enter through
openings that cannot be sealed, for
example in doors, windows, incoming/
exhaust air wall boxes or by other technical
means.
In any case, consult your responsible
Master Chimney Sweep. He is able to
assess the house's entire ventilation setup
and will suggest the suitable ventilation
measures to you.
Unrestricted operation is possible if the
vapour extractor hood is operated
exclusively in the circulating-air mode.
Risk of fire!
■ Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least every
2 months.
Never operate the appliance without the
grease filter.
■ Grease deposits in the grease filter may
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk of fire!
Risk of fire!
4
Hot oil and fat can ignite very quickly.
Never leave hot fat or oil unattended.
Never use water to put out burning oil or
fat. Switch off the hotplate. Extinguish
flames carefully using a lid, fire blanket or
something similar.
■ When gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
■ Operating several gas burners at the
same time gives rise to a great deal of
heat. A ventilation appliance installed
above the cooker may become damaged
or catch fire. Never operate two gas
burners simultaneously on the highest
flame for longer than 15 minutes. One
large burner of more than 5 kW (wok) is
equivalent to the power of two gas
burners.
Risk of burns!
The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk of injury!
■ Components inside the appliance may
have sharp edges. Wear protective gloves.
■ Items placed on the appliance may fall
down. Do not place any objects on the
appliance.
■ The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
■
Risk of fire!
Risk of fire!
Risk of injury!
Risk of injury!
Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
Causes of damage
Caution!
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the direction of the grain only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Risk of damage from returning condensate. Install the exhaust
duct in such a way that it falls away from the appliance slightly
(1° slope).
Risk of electric shock!
Environmental protection
Unpack the appliance and dispose of the packaging in an
environmentally-responsible manner.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste
electrical and electronic equipment - WEEE). The
guideline determines the framework for the return
and recycling of used appliances as applicable
throughout the EU.
Operating modes
This appliance can be used in exhaust-air mode or circulatingair mode.
Exhaust air mode
Circulating-air mode
The air which is drawn in is cleaned by the
grease filters and an activated carbon filter and
conveyed back into the kitchen.
The air which is drawn in is cleaned by the
grease filters and conveyed to the exterior
by a pipe system.
Note: The exhaust air must not be conveyed into a functioning
smoke or exhaust gas flue or into a shaft which is used to
ventilate installation rooms which contain heat-producing
appliances.
■
■
Note: To bind odours in circulating-air mode, you must install
an activated carbon filter. The different options for operating the
appliance in circulating-air mode can be found in the brochure.
Alternatively, ask your dealer. The required accessories are
available from specialist outlets, from customer service or from
the Online Shop. The accessory numbers can be found at the
end of the instructions for use.
Before conveying the exhaust air into a non-functioning
smoke or exhaust gas flue, obtain the consent of the heating
engineer responsible.
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
5
Operating the appliance
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Control panel
Interval ventilation
With interval ventilation, the ventilation system switches on
automatically for 10 minutes every hour. The appliance
switches off after 24 hours.
Note: If the intensive mode or fan run-on are activated, the
interval ventilation is not available.
1. Press the H button.
The # and H buttons light up. The interval ventilation is
switched on. The fan starts at level 1.
2. Press the H button or the # button.
The interval ventilation is switched off.
Fan run-on time
Explanation
#
Switches off the fan
1
Switches on fan level 1
2
Switches on fan level 2
3
Switches on fan level 3
Note: If the intensive mode is activated, fan run-on is not
available.
1. Select the fan level.
2. Press the y button.
The # and y buttons light up. The fan continues to run at
this fan level for 6 minutes and then switches off
automatically once this time has elapsed. If the lighting is
switched on, this is also switched off once the run-on time
has elapsed.
4/G Switches on fan level 4 or intensive mode
H
Switches on interval ventilation
y
Switches on the fan run-on
B
Switches on the lighting
3. Press the y button or the # button.
The fan run-on ends before the remaining run-on time has
elapsed.
Setting the fan
Lighting
Note: Always adjust the fan strength to meet current conditions.
If there is a large build-up of steam or fumes, select a high fan
setting.
The lighting can be switched on and off independently of the
ventilation system.
Switching on
1. Press the 1 button.
The fan starts at level 1.
2. Press the 1, 2, 3 or 4/G button to set another fan level.
The # button and the button for this fan level light up.
Switching off
Press the # button.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
1. Press and hold the 4/G button while the ventilation system is
switched on.
The # button lights up and the 4/G button flashes once
every second. Intensive mode is activated.
2. Press and hold the 4/G button or press the # button.
Intensive mode is deactivated.
Note: The run time of the intensive mode is 6 minutes. Once
this time has elapsed, the appliance switches back to the fan
level that was previously set.
6
Press the B button.
The B button lights up.
Setting the brightness
1. Press and hold the B button for 2 seconds.
The brightness is reduced.
2. Press the B button.
The maximum brightness is restored.
Saturation display
When the metal grease filters or the activated charcoal filters
are saturated, the corresponding symbol flashes:
■
Metal grease filter: H
■
Metal grease filter and activated charcoal filter: y
When this happens, do not delay cleaning the metal grease
filters or replacing the activated charcoal filters any further; see
section Cleaning and maintenance.
Resetting the saturation displays
1. Switch off the motor and the lighting.
2. Press and hold the H button.
The # button flashes 3 times. The saturation indicator for the
metal grease filter and for the activated charcoal filter is reset.
Switching over the display for circulating-air mode
For air recirculation, the electronic control display must be
switched over accordingly:
1. Check whether the extractor hood is connected and switched
off.
2. Press and hold the 3 button until the # button flashes twice.
The electronic control is switched over to air recirculation.
Cleaning protection
The appliance is equipped with a cleaning protection function.
When this function is activated, the control panel can be
cleaned without changing the settings.
Switching on
Press and hold the # button.
Switching over the display for circulating-air mode
All the buttons on the control panel flash one after the other.
Cleaning protection is switched on.
1. Check whether the extractor hood is connected and switched
Switching off
2. Press the 3 button until the # button flashes once.
Press and hold the # button until the buttons on the control
panel no longer flash.
off.
The electronic control is switched over to air extraction.
Cleaning protection is switched off.
Cleaning and maintenance
: Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
: Risk of electric shock!
Follow all instructions and warnings included with the cleaning
agents.
Area
Cleaning agents
Stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth.
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
Clean stainless steel surfaces in the
direction of the grain only.
: Risk of electric shock!
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
: Risk of injury!
Components inside the appliance may have sharp edges. Wear
protective gloves.
Painted surfaces
Cleaning agents
Observe the information in the table to ensure that the different
surfaces are not damaged by using the wrong type of cleaning
agent. Do not use
■
harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and
plastic
Glass cleaner:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Operating controls Hot soapy water:
Clean using a damp dish cloth and
dry with a soft cloth.
Risk of damage to the electronics
from penetrating moisture. Never
clean operator controls with a wet
cloth.
Do not use any stainless steel cleaners.
7
Removing metal grease filter
In the dishwasher:
1. Fold the filter cover upwards.
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
Notes
■
■
The opening angle of the filter cover is limited to approx.
80°. Do not open the filter cover any wider, as this may
damage the hinges.
The filter cover locks in any desired position.
■
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
By hand:
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
Installing the metal mesh grease filter
2. Take out the 2 metal grease filters under the filter cover.
1. Insert the 2 metal grease filters under the filter cover with the
lock facing downwards.
Fold the lock downwards, fold the metal grease filters
inwards and engage the lock.
Fold the lock downwards, pull the metal grease filter forwards
at the lock and remove it from the holder.
Note: Fat may accumulate in the bottom of the metal grease
filter. Hold the metal grease filter level to prevent fat from
dripping out.
2. Insert the metal grease filters on the underside of the
appliance.
3. Close the filter cover.
4. Press and hold the H button for 2 seconds.
The saturation indicator is reset.
Changing the activated charcoal filter (only in
circulating-air mode)
In order to guarantee efficient odour filtration, the filter must be
serviced regularly.
3. Take out the metal grease filter on the underside of the
appliance.
The activated charcoal filters must be replaced at least every
4 months.
Notes
■ The activated charcoal filters are not included in the delivery.
The activated charcoal filters can be obtained from specialist
retailers, from our after-sales service or from the Online Shop.
■
The activated charcoal filters cannot be cleaned or
reactivated.
1. Remove the metal grease filters.
2. Turn the old activated charcoal filters and pull away from the
4. Clean the metal grease filter.
5. After removing the filters, clean the inside of the appliance.
6. Clean the filter cover.
Cleaning the metal mesh grease filters
holder. ¨
3. Push the new activated charcoal filters onto the holder and
turn. ©
$
%
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
: Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
■ Do not use any aggressive, acidic or alkaline cleaning
agents.
■
■
8
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
4. Install the metal grease filters.
5. Reset the saturation indicator; see section Saturation
indicator.
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
Malfunction table
: Risk of electric shock!
Problem
Possible cause Solution
The appliance
does not work
The plug is not
plugged in.
Connect the appliance to
the electricity supply
Power cut
Check whether other
kitchen appliances are
working
Faulty fuse
Check in the fuse box to
make sure that the fuse for
the appliance is OK
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a licensed
technician (electrician).
The button illumination does
not work.
The control unit Call the after­sales service.
is faulty.
The lighting
does not work.
The bulbs are
faulty.
H or y flashes The grease filter
or the activated
in the display.
charcoal filter is
saturated.
Call the after­sales service.
Clean the filter or change
the activated charcoal filter;
see section Cleaning and
maintenance.
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate with these numbers can be
found inside the appliance (remove the metal mesh grease
filter to gain access).
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer will be
charged if a problem turns out to be the result of operator error,
even during the warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
GB
0344 892 8979
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
9
Accessories for circulated air mode
(not included in the delivery)
DHZ5335
DHZ5316
DSZ6200
DSZ5201
10
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
*9001021443*
9001021443
940829