SelecTrac™ 17T / 17THP - floor equipment parts

88
87
02
-5
32
6-
htt
ps
://m
on
ste
rflo
or
eq
uip
me
n
tpa
rts
.
co
m
SelecTrac™ 17T / 17THP
To
Or
de
rP
ar
ts
Ca
ll
1-
OPERATOR MANUAL
Kent MODELS 56648033, 56648035
7/00 Form Number 56041494(083471M-1)
co
m
rts
.
FIGURE 7
tpa
FIGURE 6
FIGURE 5
me
n
FIGURE 4
FIGURE 8
88
87
02
-5
32
6-
htt
ps
://m
on
ste
rflo
or
eq
uip
FIGURE 3
FIGURE 10
Or
de
rP
ar
ts
Ca
ll
1-
FIGURE 9
To
FIGURE 12
2 - FORM NO. 56041494 / SelecTrac™ 17T / 17THP
FIGURE 11
IMPORTANT SAFETY INSTRUCTIONS
co
m
This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices other than
normal residential housekeeping purposes.
rts
.
When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using.
tpa
WARNING!
•
•
•
uip
or
eq
rflo
ste
6-
•
on
•
://m
•
•
•
ps
•
Use machine only as described in this manual. Do not use in ways it was not intended. Use only manufacturer’s recommended
attachments.
Do not leave the machine unattended when it is plugged in. Turn off all switches and unplug the electrical cord when not in use
and before servicing.
Do not allow to be used by untrained personnel. Close attention is necessary when used near children.
If the machine is not working as it should, has been dropped, damaged, or left outdoors, return it to a service center before using.
Avoid electrical shock, do not handle the plug or machine with wet hands. To unplug the cord, grasp the plug. Do not pull on the
cord.
Do not use extension cords or outlets with inadequate current carrying capacity. Do not use with a damaged cord or plug. Connect
the machine only to a properly grounded outlet (refer to GROUNDING INSTRUCTIONS). Avoid damaging cord (closing doors
on cord, pulling around sharp edges or corners, hot surfaces, or running machine over cord).
This machine creates suction. Keep hair, loose clothing, fingers, and all other parts of the body away from openings and moving
parts. Do not insert any object into any of the openings in the machine.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Do not use the machine to pick up flammable or combustible liquids such as gasoline. Do not use in areas where flammable and/
or explosive vapor or dust is present to avoid the possibility of fire or explosion. Some cleaning fluids can produce such vapors.
Do not allow water or foam to overflow and enter the vacuum tube on the recovery tank. If this happens, immediately shut off
the vacuum motor, unplug the machine. Contact an authorized service center.
htt
•
me
n
To reduce the risk of fire, electric shock, or injury:
Failure to follow these safety instructions could result in damage to the machine, damage to property, or bodily injury.
To
Or
de
rP
ar
ts
Ca
ll
1-
88
87
02
-5
32
SAVE THESE INSTRUCTIONS
FORM NO. 56041494 / SelecTrac™ 17T / 17THP - 3
IMPORTANTES PRECAUCIONES DE SEGURIDAD
co
m
Esta máquina es sólo para uso comercial, por ejemplo en hoteles, escuelas, hospitales, fábricas, tiendas y oficinas, y no está
destinada a uso doméstico.
rts
.
Siempre que utilice aparatos eléctricos, conviene tomar las siguientes precauciones de seguridad:
Lea todas las instrucciones antes de usar el aparato.
tpa
¡ADVERTENCIA!
•
•
•
uip
or
eq
rflo
ste
on
88
87
•
://m
•
ps
•
htt
•
6-
•
32
•
-5
•
Use la máquina solamente según se describe en este manual. No la use en aplicaciones para las que no haya sido diseñada.
Use sólo los accesorios recomendados por el fabricante.
No deje la máquina desatendida cuando esté enchufada. Ponga todos los interruptores en la posición de apagado y desenchufe
el cordón de alimentación cuando no se use y antes de efectuar el servicio de la máquina.
No deje que sea utilizada por personal que no esté capacitado. Se debe prestar mucha atención cuando se utilice en las
proximidades de niños.
Si la máquina no funciona de la forma debida, se ha dejado caer, se ha dañado o se ha dejado a la intemperie, envíela a un centro
de servicio antes de volver a usarla.
Evite las descargas eléctricas. No manipule el enchufe o la máquina con las manos mojadas. Agarre el enchufe para
desenchufarla. No tire del cordón.
No use cordones de alargamiento o tomacorrientes con una capacidad de corriente inadecuada. No la use con un cordón o un
enchufe dañado. Conecte la máquina solamente a un tomacorrientes bien conectado a tierra (consulte las INSTRUCCIONES
DE PUESTA A TIERRA). Trate de no dañar el cordón (cerrando puertas y dejando el cordón aprisionado, tirando contra bordes
puntiagudos o esquinas, superficies calientes o haciendo pasar la máquina por encima del cordón).
Esta máquina crea succión y contiene un cepillo giratorio en forma de rodillo. No acerque a las aberturas y a las piezas móviles
de la máquina el cabello, ropas holgadas, los dedos y otras partes del cuerpo. No introduzca ningún objeto en ninguna abertura
de la máquina.
No haga funcionar nunca la máquina completa en escaleras. Use accesorios opcionales para ello.
No recoja nada que esté ardiendo o echando humo, como cigarrillos, cerillas o cenizas calientes.
No use la máquina para recoger líquidos inflamables o combustibles tales como gasolina. No la use en zonas donde haya
presentes vapores o polvos inflamables o explosivos a fin de impedir la posibilidad de incendios o explosiones. Ciertos fluidos
de limpieza pueden desprender tales vapores.
No deje que rebose agua o espuma ni que entre en el tubo de vacío del tanque de recuperación. Si ocurre esto, apague
inmediatamente el motor de vacío y desenchufe la máquina. Póngase en contacto con un centro de servicio autorizado.
02
•
me
n
Para evitar riesgos de incendio, choques eléctricos o heridas:
De no seguir estas instrucciones de seguridad se pueden producir daños en la máquina, daños materiales o lesiones personales.
To
Or
de
rP
ar
ts
Ca
ll
1-
GUARDE ESTAS INSTRUCCIONES
4 - FORM NO. 56041494 / SelecTrac™ 17T / 17THP
120VAC GROUNDING INSTRUCTIONS
co
m
This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric current to reduce the risk of electric
shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
rts
.
DANGER!
tpa
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician
or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
uip
me
n
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet (Figure 1) can be installed by a qualified electrician. The green-colored rigid ear, tab, or the like extending
from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place
by a metal screw. Grounding adapters are not approved for use in Canada.
or
eq
Replace the plug if the grounding pin is damaged or broken.
The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only.
rflo
Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs and outlets. DO NOT use extension cords more than
50 feet (15 m) long.
htt
ps
://m
on
ste
PLEASE NOTE: FOR NORTH AMERICA ONLY
6-
120VAC INTRUCCIONES PARA HACER LA TOMA A TIERRA
-5
02
¡PELIGRO !
32
Este aparato deberá ser conectado a tierra. En caso de malfuncionamiento o de desperfectos, la toma a tierra proporciona una vía de menor resistencia de la
corriente eléctrica para reducir el riesgo de choques eléctricos. Esta unidad viene equipada con un cordón con conductores para toma a tierra y con un enchufe
con toma a tierra. Ese enchufe deberá ser enchufado a un receptáculo en buen estado con instalación a tierra según los códigos y ordenanzas de la zona.
88
87
Si el conductor a tierra no está instalado correctamente pueden producirse riegos de choques eléctricos. En caso de duda, consulte
con un electricista o personal de servicio autorizados. No modifique el cordón provisto con el aparato. Si no calza en el receptáculo,
llame a un electricista calificado para que coloque un receptáculo adecuado.
To
Or
de
rP
ar
ts
Ca
ll
1-
Este aparato se usa con un circuito de 120-voltios nominales, y tiene un enchufe con toma a tierra tal como se muestra en la figura 1, a continuación. Se puede
usar un adaptador provisorio tal como se ve en las figuras 2 y 3 en caso de disponerse de un receptáculo sin toma a tierra como en la figura 2. Dicho adaptador
provisorio se usará solamente hasta que un electricista calificado instale un receptáculo con la toma a tierra correspondondiente (figura 1). La lengüeta de conexión
de color verde que sale del adaptador deberá ser conectada a una toma a tierra permanente como, por ejemplo, la caja del receptáculo con toma a tierra. Siempre
que se use el adaptador, hay que sostenerlo en su lugar con un tornillo de metal.
Sustituya el enchufe si la patilla de tierra está dañada o rota.
El hilo verde (o verde/amarillo) del cordón es el hilo de tierra. Cuando sustituya el enchufe, este hilo sólo debe ir conectado a la patilla de tierra.
Los cables alargadores conectados a esta máquina deben ser del calibre 12, trifilares, con tres patillas y tomas de pared adecuadas. NO UTILICE cables
alargadores de más de 15 m.
ATENCIÓN : PARA AMÉRICA DE NORTE SOLAMENTE.
FORM NO. 56041494 / SelecTrac™ 17T / 17THP - 5
Repairs, when required, should be performed by your Authorized NilfiskAdvance Service Center, who employs factory trained service personnel, and
maintains an inventory of Nilfisk-Advance original replacement parts and accessories.
Call the NILFISK-ADVANCE DEALER named below for repair parts or service.
Please specify the Model and Serial Number when discussing your machine.
CONTROLS
uip
NAME PLATE
co
m
PARTS AND SERVICE
rts
.
This product is intended for commercial use only.
tpa
This manual will help you get the most from your SelecTrac™. Read it
thoroughly before operating the machine.
PUMP PRIMING (FIGURE 6)
KX-17THP Model only - Prime the pump system by connecting the drain hose,
which is the 4 foot long solution hose with a connection on one end, to the quickdisconnect at the back of the machine and place the open end of the hose in the
solution tank. Turn on the pump, thereby recirculating the clean water through
the drain hose back into the solution tank. When there is a steady stream of
water running through the drain hose the pump is primed (usually 2-3
minutes).Turn off the pump and disconnect the priming hose and attach the
solution hose.
NOTE: The pump rarely needs to be primed after the first time. If the solution
tank is allowed to run low, which results in the pump drawing air, then the pump
may need to be primed again. Erratic pressure fluctions indicates air in the lines
and means that the pump needs priming.
me
n
INTRODUCTION
ste
rflo
or
eq
VACUUM SWITCH (FIGURE 7)
The Model Number and Serial Number of your machine are shown on the Turns the vacuum motor on to pick up solution with the recovery nozzle and
Nameplate on the machine. This information is needed when ordering repair collects it in the recovery bladder.
parts for the machine. Use the space below to note the Model Number and Serial ‘O’ is “OFF” and ‘I’ is “ON”.
Number of your machine for future reference.
PUMP SWITCH (FIGURE 7)
Turn the pump on to pump solution from the tank, through the spray nozzle to
MODEL NUMBER
the floor.
‘O’ is “OFF” and ‘I’ is “ON”.
SERIAL NUMBER
OPERATION
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it
can be inspected. Contact the Nilfisk-Advance Customer Service Department
immediately to file a freight damage claim.
Before each use, check the solution tank filter (Figure 8), vacuum lint filter
(Figure 9), recovery nozzle, and spray nozzle for lodged debris. After filling the
tank with solution, plug the power cord into a grounded outlet. Turn on the
vacuum and solution switches.
://m
ps
htt
PREPARATION
on
UNCRATE THE MACHINE
Do not allow water or foam to overflow and enter the vacuum tube
on the recovery bladder. If this happens immediately shut off the
vacuum motor, unplug the machine and contact an authorized
service center.
02
-5
32
6-
VACUUM / SOLUTION HOSE ASSEMBLY (FIG. 3,4)
This machine uses a vacuum / solution hose assembly with a wand attachment.
To assemble, connect one end of the vacuum hose to the tank lid by pushing it
on. The solution line male fitting connects to the coupling at the rear of the
machine on the base. Slide the knurled collar on the female fitting back. Push the
hose’s male fitting in, and release the knurled collar until it snaps back.The other
end of the vacuum / solution hose assembly attaches to the wand assembly in
the same way.
CAUTION!
CLEANING CARPET
Ca
ll
1-
88
87
Slowly pull the tool towards you with the solution valve trigger engaged, then
make a pass forward and backward with the vacuum only (no spray) over the
NOTE: *IMPORTANT* FOR MODEL KX-17THP
Only use wand attachments and accessories that are rated for 200 PSI or more. cleaned area to remove as much dirt and solution as possible. Make overlapping
Failure to do so could result in damage to machine, attachment, accessory, or passes to prevent streaking.
surface being cleaned. Included with your machine is a high pressure nozzle.
Use this nozzle with attachments to provide correct solution flow, pressure, and
avoid overwetting carpet.
ADDING SOLUTION (FIGURE 5)
If foam appears on vacuum lid, turn the VACUUM SWITCH OFF
WARNING!
CAUTION!
IMMEDIATELY. Add more defoamer to the recovery bladder.
de
rP
ar
ts
DISCONNECT THE POWER CORD FROM THE ELECTRICAL NOTE: DO NOT OVERWET CARPET!
If the carpet is heavily soiled, squeeze solution valve lever on the forward pass
OUTLET BEFORE ADDING SOLUTION.
Be sure the drain valve is closed. Lift lid into the upright position and pour clean and backward pass, allowing cleaning solution a few seconds longer to work
solution into the front of the tank as directed by the “Solution” arrow to the fill line. prior to vacuuming. Another method is to raise the wand 8" above the carpet and
pre-spray lightly prior to cleaning passes. On extremely soiled carpets, it is
DO NOT pour clean solution into the recovery bladder.
recommended the use of a pre-spray solution.
CAUTION!
To
Or
Solution temperature must not exceed 170°F (76°C). Use nonfoaming chemicals or defoamer and be sure to use the correct
dilution ratios.
6 - FORM NO. 56041494 / SelecTrac™ 17T / 17THP
CLEANING UPHOLSTERY
DRY VACUUMING
CAUTION!
co
m
Cleaning upholstery with success requires a good knowledge of the type of fabric
to be worked on. Look for the cleaning instruction label sewn on the underside
of the furniture for recommended method of cleaning the fabric. Extraction works
perfectly on most synthetic fabrics including synthetic velvets.
Optional dry vacuuming bag must be installed or damage to
vacuum motor will occur.
rflo
or
eq
uip
me
n
tpa
rts
.
NOTE: If the label calls for dry cleaning, do not attempt to clean with the wet
extraction method; otherwise, damage to the fabric could occur.
Open lid and install optional dry vacuuming bag on dirty solution inlet by slipping
neck of bag around inlet, and closing the clamp tight. Attach vacuum hose to inlet
Before proceeding, test the fabric for colorfastness. Apply a small amount of on lid, and preferred vacuuming tool on other end of hose. Plug the power cord
ready-to-use cleaning solution on the fabric in an inconspicuous spot. Wait for into a grounded outlet and turn on the vacuum switch.
2-3 minutes and rub the area with a white terry cloth towel. If no color comes off
onto the towel, the fabric should be safe to clean. If a little color comes off, there
CLEAN UP AND STORAGE
is some risk of colors running when you clean. It may be possible to stabilize
colors by cleaning with an acidic rinse.
Store the machine in a cool dry place. Wind the extension cord in a circle and
hang on the cord hook provided on the machine. Be sure not to wind the cord
NOTE: On KX-17THP model, adjust the pump “operating pressure” to 50 PSI or tighter than necessary.
below for upholstery cleaning (see PRESSURE ADJUSTMENT).
Avoid prolonged exposure of machine to freezing temperatures during storage
or transporting.
Prepare the machine, except attach an upholstery tool to the vacuum / solution
hose assembly.
MAINTENANCE
Clean with using as little solution as possible. Make overlapping passes to
prevent streaking. Go over the area you just cleaned without depressing the lever
(vacuum only) and gauge the amount of moisture extracted through the view
window for dryness. On heavily soiled areas like arm rests, pre-treat with a
recommended pre-spray and/or hold the upholstery tool a few inches above the AVOID POSSIBLE INJURY OR ELECTRIC SHOCK, DISCONfabric and press lever to spray on the solution before making a pass.
NECT THE POWER CORD FROM THE ELECTRICAL OUTLET.
://m
on
ste
WARNING!
htt
ps
PRESSURE ADJUSTMENT (FIGURE 10)
•
Using the pressure adjustment and gauge on the side of the unit, adjust the pump
system to the desired “operating pressure” while the cleaning tool is on (spray- •
ing).
CAUTION!
32
6-
EMPTYING THE RECOVERY BLADDER (FIG. 11)
When you run out of solution, turn off the pump. Attach the drain elbow on the
drain valve. Place a pail under the down spout and pull up the drain valve Thandle. Dirty solution will pour out until the bladder is empty. Close the drain
valve. Use a clean bucket when you refill the solution tank.
Do not use vinegar solution on carpet.
-5
EMPTYING THE SOLUTION TANK (FIGURE 12)
•
For model KX-17T, place a bucket under the drain valve. Remove the recovery
bladder fork, slide the bladder off the seal and open the drain valve.
•
For model KX-17THP there are two ways. The first is as mentioned above. The
second is by connecting the pump priming hose to the female fitting on the back
of the machine. Place the other end in a bucket and turn on the pump until the
tank is empty.
Spray quick connect coupler with WD-40 or equivalent lubricant to prevent
sticking.
Apply light oil on gate seals of drain valve.
To
Or
de
rP
ar
ts
Ca
ll
1-
88
87
02
Remove dirt and lint from the solution tank filter, vacuum lint filter, recovery
nozzle, and spray nozzle.
Reduce the build up of chemical residue by running 8 ounces of vinegar
for every gallon of water through the machine once a week. Be sure the
vinegar solution sprays into an appropriate bucket or drain. When finished,
run hot clean water through the machine.
FORM NO. 56041494 / SelecTrac™ 17T / 17THP - 7
TROUBLESHOOTING
Possible Cause
No electrical power.
Defective power cord.
Building circuit breaker tripped.
Switch is turned on, power is intermittent to all motors.
Defective power cord and or switches
Loose terminal
No vacuum
Drain valve open.
Lid not sealing on tank.
Loose vacuum hose and or conection.
Low vacuum performance
Lint build-up on lid screen.
Worn lid gasket.
Debris build-up on tool head.
Defective vacuum hose.
Loose connection in vacuum motor.
Pump is on; no spray, spray is weak, or uneven from nozzle.
Clogged nozzle, coupler, or solution filter screen.
Debris inside pump or plumbing.
Punctuered pump diaphram. (100 PSI pump only)
Defective or clogged pump check valve (100 PSI pump only)
Worn pump bearing-this makes excessive noise.
Cracked pump housing.
Defective rectifier or motor.
Lost pump prime-300 PSI pump.
Pressure regulator set incorrectly (300 PSI pump only)
Vacuum motor working, pump fails to turn on.
Loose wiring.
Defective pressure switch in pump (100 PSI pump only)
Defective pump motor rectifier.
Erratic pressure
(300 PSI only)
Pump check valves defective or dirty.
Lost prime.
To
Or
de
rP
ar
ts
Ca
ll
1-
88
87
02
-5
32
6-
htt
ps
://m
on
ste
rflo
or
eq
uip
me
n
tpa
rts
.
co
m
Problem
8 - FORM NO. 56041494 / SelecTrac™ 17T / 17THP
co
m
rts
.
tpa
me
n
uip
or
eq
rflo
ste
on
://m
ps
htt
632
-5
02
88
87
1Ca
ll
ts
de
rP
ar
Or
To
Nilfisk-Advance, Inc.
14600 21st Avenue North
Plymouth, MN, 55447-3408
www.nilfisk-advance.com
Phone:
800-989-2235
Fax:
800-989-6566
©2000 Nilfisk-Advance, Inc.,
Plymouth, MN 55447-3408
Printed in the U.S.A.