Animo
Animo
A 102 / A 202
0
1/2
1
1
0
1/2
1
1
A 202
Animo aromatic
start
start
MANUAL
GB
Animo
F
Animo
Coffeemakers
E
D
Animo
0
1/2
1
1
0
1/2
1
1
A 202
start
start
C
B
Animo
Coffeemakers
A
Animo aromatic
fig./Abb. 1
Animo
0
0
1
1
A 102
A B
Animo
0
1/2
1
1
E F
fig./Abb. 2
0
1/2
1
1
A 202
A B C
start
start
D E F
fig./Abb. 3
A 102 /A 202
10/99
Animo
Animo
Coffeemakers
0
1/2
1
1
0
1/2
1
1
A 202
start
start
600
Animo
40
Animo
Coffeemakers
~
Volt
A 202
Animo aromatic
35
160
135
235
370
240
40
385
~
Volt
10/99
A 102
200
fig./Abb. 4
A 102 /A 202
Animo
Dit apparaat voldoet aan de EMC-richtlijn 89/336/EEG, 92/31/EEG en de
laagspanningsrichtlijn 73/23/EEG.
This appliance is in accordance with the EMC-Directive 89/336/EEC,
92/31/EEC and the low voltage directive 73/23/EEC.
Dieses Gerät wurde in Übereinstimmung gemäß EMV-Richtlinie 89/336/EWG,
92/31/EWG und Niederspannung-Richtlinie 73/23/EWG gebaut.
Cet appareil est conforme à la directive d'EMC 89/336/CEE, 92/31/CEE et à
la directive de basse tension 73/23/CEE.
Animo behoudt zich het recht voor om onderdelen op elk gewenst moment te wijzigen, zonder voorafgaande of directe kennisgeving aan de afnemer.
De inhoud van deze handleiding kan eveneens gewijzigd worden zonder voorafgaande waarschuwing. Deze handleiding is geldig voor de machine in
standaarduitvoering. Animo kan derhalve niet aansprakelijk worden gesteld voor eventuele schade voortvloeiende uit van de standaard uitvoering
afwijkende specificaties van de aan u geleverde machine. Voor informatie betreffende afstelling,onderhoudswerkzaamheden of reparaties waarin
deze handleiding niet voorziet, wordt u verzocht contact op te nemen met de technische dienst van uw leverancier. Deze handleiding is met alle
mogelijke zorg samengesteld, maar Animo kan geen verantwoording op zich nemen voor eventuele fouten in dit boek of de gevolgen daarvan.
Animo has the right to change parts of the machine at any time without advice or direct announcements to the client. The contents of this manual can
also be changed without any announcements. This manual is to be used for the standard model/type of the machine. Thus Animo cannot be held
responsible for any damage resulting from the application of this manual to the version delivered to you. For extra information on adjustments
maintenance and repair, contact the technical department of your supplier. This manual has been written very carefully. However, Animo cannot be
held responsible neither for mistakes in the book nor for their consequences.
Animo behält sich das Recht vor, Einzelteile ohne vorherige Bekanntgabe an den Kunden zu ändern. Der Inhalt dieser Anleitung kann ebenfalls ohne
vorherige Bekanntgabe geändert werden. Diese Anleitung gilt für die Standardausführung der Maschine. Animo haftet daher nicht für Informationen
über Einstellungen, Wartungsarbeiten oder Reparaturen, die nicht in dieser Anleitung enthalten sind. Wenden Sie sich bitte gegebenenfalls an den
Kundendienst Ihres Händlers. Diese Anleitung wurde mit größtmöglicher Sorgfalt zursammengestellt. Animo haftet jedoch nicht für etwaige Fehler in
dieser Anleitung oder für die Folgen solcher Fehler.
Animo se réserve le droit de modifier les pièces à n’importe quel instant, sans avis préalable et sans obligation de notification au client. Le contenu de
ce manuel est également sujet à modification sans avis préalable. Ce manuel s’applique au modèle standard de la machine. Par conséquent, Animo
n’est past responsable pour les dommages éventuels découlant de l’application de ce manuel aux modèles non standard. Pour les renseignements
sur certains réglages, les travaux d’entretien ou réparations qui ne seraient pas traités dans ce manuel, Animo ne peut ètre tenu responsable des
erreurs éventuelles ni des dommages qui en dècouleraient.
A 102 /A 202
10/99
Animo
GB
TABLE OF CONTENTS
1.
GENERAL DESCRIPTION ........................................................................................ 2
2.
TECHNICAL DETAILS ............................................................................................. 2
3.
INSTALLATION .......................................................................................................
3.1
Position the machine ..........................................................................
3.2
Connecting to the water supply system (A 202) ..............................
3.3
Connecting to the electricity supply system .....................................
4.
CONTROL PANEL ................................................................................................... 4
5.
PREPARATION BEFORE USE ................................................................................. 4
5.1
A 102 (manual filling) ........................................................................ 4
5.2
A 202 (automatic filling) .................................................................... 4
6.
USE
6.1
7.
MAINTENANCE .......................................................................................................
7.1
Cleaning (daily) ...................................................................................
7.1.1
Removal of coffee fur .........................................................................
7.2
Descaling .............................................................................................
8.
TRANSPORT ............................................................................................................ 6
A 102 /A 202
3
3
3
3
............................................................................................................... 5
Brewing coffee .................................................................................... 5
1
5
5
6
6
10/99
Animo
This instruction was designed for users of the Animo coffeemaker, type A 102 and A 202.
These operating instructions should be read carefully to ensure that your coffee machine is operated
correctly and safely.
1. GENERAL DESCRIPTION
The Aromatic A 102 is a semi-automatic coffee machine. The Aromatic A 202 is an automatic model with a
fixed water connection and a selector switch to choose a full or a half jug of coffee.
The machine is started by simply pressing the button. The flow through design eliminates initial water
heating time and so provides a faster brew.
In figure 1 the main parts are indicated.
In figure 2 and 3 the controls are indicated.
Figure 1.
A - Lower hot plate
B - Glass jug 4x
C - Basket filters (90/250) 3x
D - Switch panel
E - Upper hot plate
F - Water reservoir
(art.nr. 08208)
(art.nr. 08635)
The machine is supplied with the following accessories:
- Measuring spoon
- Basket filter paper 90/250 approx. 50 pieces (art.nr. 01088 1000 pieces)
- Water supply hose approx. 1.5 m long (type A 202)
- 2 sachets coffee fur remover (100 sachets for 10 grams art.no. 49009)
- 2 sachets descaling agent (48 sachets for 50 grams art.no. 49007)
- Operating manual
2. TECHNICAL DETAILS
Type
Article number
Approx. hourly capacity coffee
Buffer supply coffee
Brewing time
Minimum amount of coffee
Electrical connection
Level detection
Water connection
Min. - Max. water pressure
Paper filter
Dimension
Weight
:
:
:
:
:
:
:
:
:
:
:
:
:
A 102
10249
30 ltr., 240 cups
7,2 ltr., 58 cups
abt. 7 min./1.8 Ltr.
1/2 Jug
1N~220-240V/50-60Cy/3550W
electronic
n/a
n/a
90/250
See fig.4
16 kg
A 202
10257
30 ltr., 240 cups
7,2 ltr., 58 cups
abt. 7 min./1.8 Ltr.
1/2 Jug
1N~220-240V/50-60Cy/3550W
electronic
G 3/4”
1-8 bar
90/250
See fig.4
16 kg
Technical alterations are reserved
10/99
2
A 102 /A 202
Animo
WARNING
*
*
*
*
*
*
*
*
*
!
Always observe local rules while installing the unit and use approved materials and parts.
Always remove the plug from the socket if the machine has to be opened for repair or
maintenance.
Do not put the machine in areas where the temperature drops below freezing point
because there is always water left in the system.
Always plug the machine into an earthed wall socket.
Connect the machine to the cold watertap (type A 202).
Do not submerge or spray the machine.
Make sure that the main cable does not come into contact with the hot plates.
Have all repairs carried out by an especially trained technician.
If the machine is not used it is advisable to remove the plug from the socket and to turn off
the water tap *. (type A 202).
3.3 Connecting to the electricity
supply system
Depending on the model, the appliance
should be connected according to the
instructions in the figures below.
3. INSTALLATION
Before installing the machine, carry out the
following steps:
3.1 Position the machine
•
at counter level and on a solid flat surface.
•
so that it is near the water and electricity
supply system.
•
so that it is not causing any damage in
case of leakage.
•
so that the ventilation holes in the back
of the appliance are not blocked.
•
•
The following remarks apply to figure 5:
•
If the plug fitted on the machine cable does
not fit in your socket, replace it with a new
plug that does fit.
•
The replaced plug should be disposed of as
it can be dangerous if plugged in a socket.
3.2 Connecting to the water supply
system (A 202)
•
The machine requires water stop valve to
be near the appliance.
•
The water supply system should be within
reach of the 1.5 meters long water hose.
•
Connect the water hose that comes with the
system to the cold water supply and to
the water connection point at the back of
the machine.
•
When positioning the machine, bear in
mind that it is equiped with an overflow.
The following points should be observed when
wiring a new plug:
1.
2.
3.
A 102 /A 202
(Fig. 5) For 220V-240V 1 Phase/neutral
with plug socket.
(Fig. 5) For 220V -240V 1 Phase/neutral
(3 core electric cable).
3
The green/yellow-coloured wire (“EARTH”)
should be connected to the terminal which
is either marked with the letter “E”, the
“earth” symbol ( ), or coloured green or
green/yellow.
The blue-coloured wire (“NEUTRAL”) should
be connected to the terminal which is either
marked with the letter “N” or coloured
black.
The brown-coloured wire (“PHASE”) should
be connected to the terminal which is either
marked with the letter “L” or coloured red.
10/99
Animo
IMPORTANT !
The three core main cables (fig. 5) have the
following wiring code:
Green/Yellow - Earth
Blue
- Neutral
Brown
- Phase
5. PREPARATIONS BEFORE
USE
Before operating the machine, carry out the
following steps:
5.1 A 102 (manual filling)
1.
Pour a jug of cold water in the cold water
reservoir (fig. 1F).
2.
Slide the basket filter into the machine and
place an empty jug on the lower hot plate.
3.
After you have followed the instructions
above, place the plug in the socket and turn
the machine on using the main switch
(fig. 2B).
4.
The orange alarm lamp (fig. 2A) will now
light up until the machine has emptied.
When the light goes out again the coffee
unit is ready for use.
Green/Yellow - Earth (E)
Blue
- Neutral (N)
Brown
- Live
(L)
fig. 5
4. CONTROL PANEL
A 102 (manual filling fig. 2)
A - Alarm lamp for heating element
B - On/off switch
5.2 A 202 (automatic filling)
1.
Connect the supplied water hose to the
coupling nut swivel joint at the rear of the
machine and to a manually-operated
water tap. ATTENTION! Use cold water
only.
2.
Slide the basket filter into the machine and
place an empty jug on the lower hot plate.
3.
After you have followed the instructions
above, place the plug in the socket.
4.
Turn on the machine by using the switch
(fig. 3B).
5.
Turn the selection switch (fig. 3C) to the
desired amount.
6.
Press the start switch (fig. 3D) and the
water reservoir will fill up.
7.
The orange alarm lamp (fig. 3A) will now
remain lit until the water has run through.
The machine is ready for use when the lamp
has gone out again.
E - On/off switch for upper hot plate
F - On/off switch for lower hot plate
A 202 (automatic filling fig. 3)
A - Alarm lamp for heating element
B - On/off switch
C - Selection switch for full or half jug
D - Start switch
E - On/off switch for upper hot plate
F - On/off switch for lower hot plate
10/99
4
A 102 /A 202
Animo
6. USE
•
•
•
WARNING
Basic rules for making coffee:
Use extra-fine grind (approx. 40 grams per
litre).
Keep the thermos jug and the basket filters
clean.
Hint! Keep a pile of basket filter papers in
the spare sliding filter or place a filter paper
with coffee in this filter so that the next
serving can be prepared without losing
time.
-
6.1 Brewing coffee
1.
Place the filter paper (90/250) with the
appropriate amount of coffee (fine ground
for filter coffee units) in the basket filter.
The amount can be measured with the
supplied measuring spoon.
Generally speaking, you will need about 70
- 80 grams per 1.8 l jug.
2.
Slide the basket filter into the machine and
place an empty jug on the lower hot plate.
3.
Check if the machine is switched on,
main switch on (fig. 2B & 3B), and switch
on the lower hot plate (fig. 2F & 3F).
4.
4.
5.
6.
7.
8.
-
Stay near the machine while
maintenance is being carried out.
When descaling the machine, always
observe the instructions for use
provided with the descaling agent.
When descaling the machine, it is
advisable to wear safety goggles and
protective gloves.
Allow the machine to run through at
least three times after it has been descaled.
Wash your hands thoroughly after
descaling.
The machine should not be submerged
or sprayed.
Have all repairs carried out by a
especially trained technician.
7. MAINTENANCE
•
•
•
A 102 (manual filling)
Pour a jug of cold water in the cold water
reservoir (fig. 1F), and place the empty jug
directly on the lower hot plate.
For daily cleaning, see section 7.1
For removal of coffee fur, see section 7.1.1
For descaling, see section 7.2
7.1 Cleaning (daily)
•
The machine can be cleaned with a clean,
damp cloth.
•
Avoid using abrasive. It can cause scratches
and dim spots.
•
The jug and basket filter can be washed
normally.
Attention! The basket filter should not
be placed in a dishwasher.
•
Coffee stains in the jugs can be removed
using Animo coffee stain remover.
A202 (automatic filling)
Turn the selection switch (fig. 3C) to the
required amount and press the start switch
(fig. 3D).
The orange signal lamp (fig. 2A & 3A) on
the machine will now light up and the filter
coffee will be prepared.
When the signal lamp goes out again,
the hot water supply will stop. After about
1 minute, all of the coffee will have gone
through the filter.
Stir the coffee in the jug briefly and pour
or place the full jug on the upper hot plate.
The upper hot plate can be switched on
separately using the appropriate switch
(fig. 2E & 3E).
The machine is ready to be used again after
the basket filter has been cleaned.
A 102 /A 202
!
•
The machine can leave lime deposits
during use. The machine should be descaled
regularly in order to ensure that it functions
efficiently. Animo scale remover is
recommended.
Animo supplies both products in the
following quantities:
Coffee detanning agent
100 sachets for 10 grams - art.no. 49009
Descaling agent
48 sachets for 50 grams - art.no. 49007
5
10/99
Animo
7.1.1 Removal of coffee fur
A sachet of coffee fur remover solvent is
supplied with the machine. Usage is
extremely simple.
1.
Take a bowl filled with ca. 5 litres warm
water and dissolve the coffee fur remover
solvent from the sachet into it.
2.
Put the parts that need to be cleaned in the
bowl and soak them for 15 to 30 minutes.
3.
Rinse several times with warm water. Repeat
treatment if the result is insufficient.
4.
Scatter coffee fur remover solvent on very
filthy spots and clean with a wet brush.
7.2 Descaling
1.
Switch off the machine (fig. 2B & 3B).
2.
Slide the basket filter into the machine and
place an empty jug on the lower hot plate.
3.
Dissolve 1 sachet of 50 grams of Animo
descaling agent in 1 litre of lukewarm 60 70˚C water (see instructions for use on the
labelling).
4a
4b
4a.
4b.
4c.
5.
When half of the solution has run through
the machine, switch it off for about 2
minutes (fig. 2B & 3B). The solution will
now undergo a reaction with the lime scale.
10/99
*
Attention! Keep an eye on the reservoir
while the solution is running through the
machine. Turn the machine off as soon as
the reservoir is empty. Then rinse clean the
metal contacts in the cold water reservoir
with water or a wet cloth.
7.
After descaling the machine, rinse
thoroughly by carrying out the normal
coffee preparation process 3 times (without
paper filters and coffee).
Clean the basket filter and jug thoroughly.
The machine is now ready to be used again.
8. TRANSPORT
The following procedure should be followed when
the appliance is transported:
1.
2.
3.
4.
A 202 (automatic filling)
Pour 1 litre of Animo descaling agent into
the reservoir (fig. 1F) and switch on the
machine (fig. 3B).
Turn the selection switch (fig. 3C) to the
half position and press the start button
(fig. 3D). The solution will now begin to
flow through the system.
Leave the reservoir lid open!
Attention! If the machine begins to steam
heavily, switch it off immediately (fig. 2B
& 3B). Wait for 1 minute. The solution will
flow through automatically. Switch the
machine back on. Press the start button
(fig. 2D) as well (A 202 only).
After the pause, switch the machine back
on and allow the rest of the solution to
flow through the machine. Press the start
button again (fig. 3D) (A 202 only).
8.
9.
A 102 (manual filling)
Pour 1 litre of Animo descaling agent into
the reservoir (fig. 1F) and switch on the
machine (fig. 2B). The solution will now
begin to flow through the system.
Leave the reservoir lid open!
*
6.
5.
6.
7.
6
Switch off the machine (fig.2B & 3B) and
remove the plug from the wall socket.
Close the water supply tap and disconnect
the supply hose.
Remove the jugs and the basket filter.
Empty the machine, by turning it upside
down above the sink, so that the remaining
water runs out through the spray head
(attention: the water can still be hot!)
Wipe the machine dry, and replace all the
components that have been removed.
The machine is now ready for transport.
When it is relocated, the procedures of
“Installation”, should be followed.
A 102 /A 202
0992 Rev. 1 271099 Animo 09920
Animo B.V. Headoffice
Dr. A.F. Philipsweg 47
P.O. Box 71
9400 AB Assen
The Netherlands
Tel. no. +31 (0)592 376376
Fax no. +31 (0)592 341751
E-mail: info@animo.nl
Internet: http://www.animo.nl
Accredited by
the Dutch Council
for Certification
Download PDF