Operating Instructions
50cm Gas Cooker
Contents
GB
GB
English, 1
Introduction, 2-3
For Your Safety, 4
Installation Instructions,5-8
Burner and Nozzle Specification, 8
Features, 9
Control Panel, 10
Hotplate, 11
Grill, 12
Oven, 13
Oven Cooking Chart, 14
Care and Cleaning, 15
Cooking Results Not Satisfactory?,16
Something Wrong with your cooker?, 17
Disposal of the appliance, 18
Guarantee Information, 19
ea
08 se
to 44 ph
a 8 o
gu ctiv 24 ne
ar ate 24 us
an y 2 on
te ou 4
e r
Service Information, 20
Pl
HAGL 51 P
HAGL 51 K
Introduction
GB
To the Installer:
Before installation, fill in the product details on the back
cover of this book.
The information can be found on the rating plate.
To the User:
You must read the instructions prior to installing and
using the appliance and then retain them for future
reference.
! Before operating your new appliance please read
this instruction booklet carefully. It contains important
information concerning the safe operation, installation
and maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Retention of this Instruction Book
This Instruction Book must be kept handy for reference
as it contains important details on the safe and proper
use of the appliance.
If you sell or pass the appliance to someone else, or
move house and leave it behind, make sure this Book
is also provided so the new owner can become familiar
with the appliance and safety warnings.
Your new appliance is guaranteed* and will give
lasting service. This guarantee is only applicable if the
appliance has been installed in accordance with the
installation instructions detailed in this booklet.
To help make best use of your cooking equipment,
please read this booklet carefully.
The cooker is designed specifically for domestic use
and responsibility will not be accepted for use in any
other installation.
When the cooker is first used an odour may be
emitted, this will cease after a period of use.
When first using the cooker ensure that the room is well
ventilated (e.g. open a window or use an extractor fan)
and that persons who may be sensitive to the odour
avoid any fumes.
Your new cooker is guaranteed and will give lasting
service.
The guarantee is only applicable if the cooker has
been installed in accordance with the Installation
Instructions.
The cooker is designed specifically for domestic use
and responsibility will not be accepted for use in any
other installation.
* The guarantee is subject to the provisions that the
appliance:
(a)
Has been used solely in accordance with
the Users Instruction Book.
(b)
Has been properly connected to a suitable
supply voltage as stated on the rating plate
attached to this equipment.
(c)
Has not been subjected to misuse or
accident or been modified or repaired by
any person other than the authorised
employee or agent.
(d)
Has been correctly installed.
Our policy is one of continual improvement in design
and development, therefore strict accuracy of
illustrations and descriptions cannot be guaranteed.
This appliance conforms with the following European
Economic Community directives:
-
2009/142/EC of 30/11/09 (Gas) and subsequent modifications (only for models which use gas);
93/68/EEC of 22/07/93 and subsequent modifications.
2002/96/EC
-
1275/2008 (Stand-by/ Off mode)
It is suggested that any pets be removed from the
room until the smell has ceased. This odour is due to
temporary finish on oven liners and elements and also
any moisture absorbed by the insulation.
2 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Electrical connection
THE APPLIANCE MUST BE EARTHED
Install a standardised plug corresponding to the load indicated
on the appliance data plate (see Technical data table).
The appliance must be directly connected to the mains using
an omnipolar switch with a minimum contact opening of 3
mm installed between the appliance and the mains. The
switch must be suitable for the charge indicated and must
comply with current electrical regulations (the earthing wire
must not be interrupted by the switch). The supply cable
must be positioned so that it does not come into contact
with temperatures higher than 50°C at any point.
Before connecting the appliance to the power supply, make
sure that:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the
appliance, which is indicated by the data plate.
• The voltage is in the range between the values indicated
on the data plate.
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only.
! The manufacturer declines any liability should these
safety measures not be observed.
IF THE FITTED PLUG IS REMOVED
The flexible mains lead must be correctly connected as
below to a three pin plug of not less than 13 amp capacity.
If a B.S. 1363 fused plug is used, it must be fitted with a
fuse which is approved to B.S. 1362.
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow - Earth
Blue
- Neutral
Brown
- Live
The power supply cable must be type H05VV-F
Green &
Yellow to
Earth
Blue to
Neutral
Connect the Green & Yellow wire to terminal marked “E”
or
or coloured Green or Green & Yellow.
Connect the Brown wire to the terminal marked “L” or
coloured Red.
Connect the Blue wire to the terminal marked “N” or
coloured Black.
FAILURE TO OBSERVE THE ACCIDENT-PREVENTION
REGULATIONS RELIEVES THE MANUFACTURER OF
ALL LIABILITY.
IF A MOULDED PLUG IS FITTED
In the event of replacing a fuse in the plug supplied an ASTA
approved fuse to BS1362 must be fitted.
NOTE: The fuse cover must be refitted when changing the fuse.
In the event of losing the fuse cover the plug must not be used
until a replacement fuse cover has been obtained and fitted. A
new fuse cover can be obtained from your local Electricity Board.
The colour of the correct replacement fuse cover is that of the
coloured marks or inserts in the base of the plug.
Make sure that the cable does not become trapped when
pushing the cooker into position.
Replacing the cable
Use a rubber cable of the type H05VV-F with a cross section
of 3 x 1.5 mm². The yellow-green earth wire must be 2 ÷ 3
cm longer than the other wires.
Technical Characteristics
Grill
Main Oven
ENERGY LABEL
and ECODESIGN
Usable Volume: 19 Litres
heating mode: Conventional
Usable Volume: 41 Litres
heating mode: Conventional
Regulation (EU) No 65/2014 supplementing Directive 2010/30/EU.
Regulation (EU) No 66/2014 implementing
Directive 2009/125/EC.
Standard EN 15181.
Brown
to Live
Hob
3 Amp
Fuse
ECODESIGN
Regulation (EU) No 66/2014 implementing
Directive 2009/125/EC.
Standard EN 30-2-1
Cord
Clamp
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
GB
Voltage and Frequency
220-240V~ 50/60Hz
3
For your Safety
NEVER
ALWAYS . . .
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
ALWAYS
make sure you understand the controls before using
the cooker.
check that all controls on the cooker are turned off
after use.
stand back when opening an oven door to allow heat
to disperse.
use dry, good quality oven gloves when removing
items from the ovens.
take care when removing items from the top oven/
grill when the main oven is on, as the contents may
be hot.
keep the oven and grill doors closed when the cooker
is not in use.
place pans centrally over the hotplate burners and
position them so that the handles cannot accidentally
be caught or knocked or become heated by other
burners.
keep the cooker clean, as a build up of grease or fat
from cooking can cause a fire.
allow the cooker to cool before cleaning.
follow the basic principles of food handling and
hygiene to prevent the possibility of bacterial growth.
keep ventilation slots clear of obstructions.
turn off the electricity supply before cleaning or replacing an oven lamp.
refer servicing to gas safe registered appliance service
engineers.
NEVER
NEVER
NEVER
NEVER
ALWAYS
NEVER
NEVER
NEVER
NEVER
NEVER
NEVER
Do not let children play with the appliance.
The appliance should not be operated by people (including children) with reduced physical, sensory or
mental capacities, by inexperienced individuals or by
anyone who is not familiar with the product. These
individuals should, at the very least, be supervised
by someone who assumes responsibility for their
safety or receive preliminary instructions relating to
the operation of the appliance.
! VERY HOT SURFACES
FOOD OR GREASE ON THESE
SURFACES COULD CAUSE
SMOKE AND POSSIBLY EVEN BURN
NEVER . . .
NEVER
NEVER
in or on the cooker, or in cabinets immediately above
or next to the cooker.
fill a deep fat frying pan more than 1/3 full of oil,
and never use a lid. DO NOT LEAVE UNATTENDED
WHILE COOKING.
place flammable or plastic items on or near the
hotplate.
use proprietary spillage collectors on the hotplate.
use the cooker as a room heater.
dry clothes or place other times over or near to the
hotplate or oven/gril doors.
wear garments with long flowing sleeves whilst cooking.
leave children unsupervised where the cooker is
installed as all surfaces will get hot during and after
use.
allow anyone to sit or stand on any part of the cooker.
store items that children may attempt to reach above
the cooker.
heat up unopened food containers as pressure can
build up causing the container to burst.
store chemicals, food stuffs, pressurised containers
The appliance must be used by adults only for the preparation of food, in accordance with the instructions
outlined in this booklet. Any other use of the appliance
(e.g. for heating the room) constitutes improper use
and is dangerous. The manufacturer may not be
held liable for any damage resulting from improper,
incorrect and unreasonable use of the appliance.
NOTE: The use of a gas cooking appliance results in the
production of heat and moisture in the room in which it is
installed. Always ensure that the kitchen is well ventilated; keep
natural ventilation holes open or install a mechanical ventilation
device (mechanical extractor hood).
YOU MUST KEEP THE OVEN
AND GRILL CAVITIES CLEAN
! ATTENTION
DURING INSTALLATION
THE FEET OF THE APPLIANCE
MUST BE LOWERED SO THAT
AN AIR GAP OF AT LEAST
10MM (1CM) IS LEFT BETWEEN
THE BASE OF THE APPLIANCE
AND THE FLOOR.
10 mm
Please read the precautions below before using your cooker.
GB
! ATTENTION
WHEN USING THE MAIN OVEN
YOU MUST ENSURE THAT THE
BASE OF THE CAVITY IS NOT
COVERED WITH ALUMINUM
FOIL, UTENSIL OR ANY OTHER
FORM OF COVERING. FAILURE
TO DO THIS MAY RESULT IN
THE CAVITY BEING DAMAGED.
In particular when using the grill or more than one hotplate
burner, open a window if a mechanical ventilation device is not
operating.
4 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Installation
Installation of the cooker
a) The cooker should not be installed in a bed sitting
room with a volume of less than 20m3. If it is installed
in a room of volume less than 5m3 an air vent of
effective area of 110cm2 is required, if it is installed
in a room of volume between 5m3 and 10m3 a
supplementary airvent area of 50cm2 is required,
if the volume exceeds 11m3 no airvent is required.
However, if the room has a door or a window which
opens directly to the outside no air vent is required
even when the volume is between 5m3 and 11m3.
b) During prolonged use of the appliance you may
consider it necessary to open a window to the
outside to improve ventilation.
c) If there are other fuel burning appliances in the
same room, B.S.5440 Part 2 Current Edition, should,
be consulted to determine the requisite air vent
requirements.
Tall cupboard on the right hand
side of 50cm gas cooker
400 mm min
500 mm min
150 mm min
Tall cupboard on the left hand
side of 50cm gas cooker
65 mm min
65 mm min
Important: this unit may be installed and used only in
permanently ventilated rooms according to the British
Standards Codes Of Practice: B.S. 6172/B.S. 5440,
Par. 2 and B.S. 6891 Current Editions. The following
requirements must be observed:
750 mm min
Positioning
a) The cooker may be located in a kitchen, a kitonen/
diner or bed sitting room, but not in a bathroom or
shower room.
b) The hoods must be installed according to the
requirements in the hood handbook.
c) The wall in contact with the back of the cooker must
be of flameproof material.
d) The cooker is fitted with a safety chain that must be
attached to a hook, secured to the wall behind the
appliance.
Note: some models can have their gas connection
inverted. It is important to make sure the safety chain
is always situated on the side which corresponds to
the hose holder (Fig. B).
750 mm min
Important: remember to unplug the appliance from the
mains before regulating the appliance or carrying out
any maintenance work.
GB
For a correct installation of the cooker the following
precautions must be followed:
The height of the cooker can be adjusted by means of
adjustable feet in the plinth (900mm - 915mm). Adjust
the feet by tilting the cooker from the side. Then install
the product into position.
NOTE: This appliance must not be fitted on a platform.
The cooker is designed to fit between kitchen cabinets
spaced 500mm apart. The space either side need
only be sufficient to allow withdrawal of the cooker for
servicing. It can be used with cabinets one side or
both as well as in a corner setting. It can also be used
free-standing.
Adjacent side walls which project above hob level,
must not be nearer to the cooker than 150mm or 65mm
(Fig. A) and should be protected by heat resistant
material. Any overhanging surface or cooker hood
should not be nearer than 750mm. (Fig.A)
65 mm min
The appliance must only be installed by a competent
person. In the UK, gas safe registered installers
undertake to work to safe and satisfactory standards.
Before moving your cooker check that it is cool, and
switch off at the cooker control unit. Movement of your
cooker is most easily achieved by lifting the front as
follows:
Open the grill door sufficiently to allow a comfortable
grip on the underside front edge of the oven roof,
avoiding any grill elements.
Note: Take care in moving the cooker as it is heavy.
Take care to ensure that any floor covering is not
damaged. (FIG. C)
Splashplate optional, apply to Parts Department (see
Back Cover for contact number.)
The following instructions should be read by a qualified
technician to ensure that the appliance is installed,
regulated and technically serviced correctly in
compliance with current regulations.
400 mm min
500 mm min
Fig. A
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
5
Installation
Moving the Cooker
Connecting the gas supply
GB
Fig. B
Fig. C
Gas connection
600 mm
The cooker should be connected to the gas-supply
by a gas safe registered installer. During installation
of this product it is essential to fit an approved gas
tap to isolate the supply from the appliance for the
convenience of any subsequent removal or servicing.
Connection of the appliance to the gas mains or liquid
gas must be carried out according to the prescribed
regulation in force, and only after it is ascertained that it
is adaptable to the type of gas to be used. If not, follow
the instructions indicated in the paragraph headed
“Adaptation to different gas types”. On some models
the gas supply can be connected on the left or on the
right, as necessary; to change the connection, reverse
the position of the hose holder with that of the cap and
replace the gasket (supplied with the appliance). In the
case of connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The
gas supply must be
connected to the
HOT PARTS
left of the appliance.
Be sure that the
hose does not pass
through the rear of
the cooker touching
hot parts.
! Make sure the
supply pressure
conforms with the values shown in the table entitled
“Caracteristics of the burners and nozzles”.
When the cooker is installed between cabinets
(recessed), the gas connection must be effected
by an approved flexible hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for the cookers
is a threaded G 1/2 gas female fitting.
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
• the hose must never be at any point in its lenght in
contact with the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or
torsional stress and it must not have any excessively
narrow curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
• the hose must always be in good condition, never
attempt to repair.
! The installation must comply with gas safety
(installation and use) regulations 1984. In all cases for
the above, by low, a qualified, gas safe approved engineer
must be called for installation.
Disposing of the appliance
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible to
the plug body and dispose of it as described above.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas
with respect to the gas for which it was produced
(indicated on the label attached to the lid), follow these
steps:
a) replace the hose holder mounted on the
appliance with that supplied in the bag of
“cooker accessories”.
b) Replacing the burner nozzles on the hob:
• remove the grids and slide the burners from their
housings;
• unscrew the nozzles using a 7 mm socket spanner,
and replace them with
nozzles for the new
type of gas (see table
1 “Burner and nozzle
characteristics”).
• replace all the
components by repeating
the steps in reverse order.
6 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Installation
c) Minimum regulation of the hob burners:
• turn the tap to minimum;
• remove the knob and adjust the regulation screw,
which is positioned in or next to the tap pin, until the
flame is small but steady.
! In the case of liquid gas, the regulation screw must
be screwed in to the
bottom.
• check that the flame
does not turn off when
you turn the tap quickly
from high to low.
d) Regulating the primary
air of the burners:
The primary air of the
burners requires no regulation.
Take particular care handling the spark plug wires
and the thermocouple pipes.
• Replace all the parts, following the steps described
above in the reverse order.
b) Minimum regulation of the gas oven burner with
thermostat:
• light the burner as described in the paragraph “the
oven knob” of the instruction booklet.
• turn the knob to Max for about 10 minutes and then
turn the knob to the Min setting;
• remove the knob;
• regulate the screw positioned outside the thermostat
pin until the flame is small but steady.
! In the case of liquid gas, the regulation screw must
be screwed in to the bottom.
Adapting to different types of gas
In order to adapt the oven to a different type of gas
with respect to the gas for which it was manufactured
(indicated on the label), follow these simple steps:
a) Replacing the oven burner nozzle
• check that the burner does not turn off when you
turn the knob from Max to Min and and when you
open and close the oven door quickly.
• open the oven door fully
• pull out the sliding oven bottom
• unscrew the two screws and take off the shield
protecting the burner (in main oven burner only).
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
V
Adapting the gas grill to different types of gas
Replacing the nozzle of the grill burner:
• remove the screw and then slide out the grill burner
“V” (see Fig. E);
• unscrew the grill burner nozzle using the special
socket spanner for the nozzles (see Fig. F) or better
still a 7 mm socket spanner; replace the nozzle with
a nozzle for the new type of gas (see table 1).
Z
V
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
7
GB
Burner and Nozzle
Specification
GB
V
I
Fig.E
Fig.F
Important
On completion of the operation, replace the old rating
sticker with one indicating the new type of gas used.
This sticker is available from our Service Centres.
Note
Should the pressure of the gas used be different (or
vary) from the recommended pressure, it is necessary
to fit a suitable pressure regulator onto the inlet pipe in
compliance with current National Regulations relative
to “regulators for channelled gas”.
Table 1
Burner
HAGL 51 P
HAGL 51 K
A
Liquid Gas
Diameter
(mm)
Thermal Power
kW (p.c.s.*)
S
By-Pass Nozzle
1/100
1/100
S
R
Natural Gas
Flow*
g/h
Nozzle
1/100
Nominal
Reduced
(mm)
(mm)
***
**
(mm)
Flow*
l/h
Fast
(Large)(R)
100
94
2,60
0,7
41
80
189
186
118
286
Semi Fast
(Medium)(S)
75
69
1,90
0,4
30
70
138
136
104
181
Auxiliary
(Small)(A)
51
46
1,00
0,4
30
52
73
71
76
95
Oven
-
2,60
0,6
36
71
189
186
115
248
Grill
-
2,50
1,3
63
80
182
179
122
238
28-30
20
35
37
25
45
Supply
Pressures
*
**
***
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
20
17
25
At 15°C and 1013 mbar- dry gas
Propane
P.C.S. = 50,37 MJ/Kg
Butane P.C.S. = 49,47 MJ/Kg
Natural P.C.S. = 37,78 MJ/m3
8 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Features
GB
HOB VENTILATION SLOTS
1900W
1000W
1900W
2600W
CONTROL
PANEL
GRILL/MEAT PAN
WITH REMOVABLE
HANDLE AND WIRE
FOOD SUPPORT
GRILL/TOP OVEN
MODEL & SERIAL
NUMBER
GRILL DOOR
DOOR
INNER GLASS
MAIN OVEN
WIREWORK
SHELF
SUPPORTS
'STAY CLEAN' PANEL
OVEN ROD
SHELVES
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
9
Control Panel
MAIN
OVEN
GB
LEFT
FRONT
BURNER
GRILL
LEFT
REAR
BURNER
RIGHT
REAR
BURNER
RIGHT
FRONT
BURNER
ELECTRONIC*
INIECTION
BUTTON
Control Knobs for the gas burners
The position of the gas burner controlled by each one of the knobs is shown by a solid ring •. To light one of the
burners, press down and turn the corresponding knob counter clockwise to the maximum E setting. Each burner
can be operated at its maximum, minimum or intermediate power. Shown on the knob are the different symbols
for off • (the knob is on this setting when the symbol corresponds with the reference mark on the control panel),
for maximum E and minimum C. To obtain these settings, turn the knob counter clockwise with respect to the off
position. To turn off the burner, turn the knob clockwise until it stops (corresponding again with the • symbol).
Electronic Ignition for the Gas Hob*
This device operates when a slight pressure is applied to the button marked with
symbol. To light a specific
while pushing the corresponding knob all the way in and turning it counter-clockwise
burner just press the button
until it lights. For immediate lighting, first press the button and then turn the knob.
! Should the burner flames accidentally go out, turn off the control knob and wait at least 1 minute before
trying to relight.
Grill Control
This control switches on the top heating elements in the top oven..
The temperature of the top oven can be set anywhere between 80°C and 230°C by turning the knob clockwise.
To set the grill turn the corresponding knob to
E
The grill can be operated at minimum C.and maximum E setting.
Main Oven Control
This control switches on the top and rear heating elements at various times in the main oven, dependent on which
mode has been set.
The temperature of the main oven can be set anywhere between 80°C and 230°C by turning the knob clockwise from
1 to 9.
10 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Hotplate
The hotplate lid is fitted with a safety device which cuts
off the gas supply to the hotplate burners unless the lid
is fully open. Do not use the safety device as a means
of controlling the hotplate burners.
The hotplate has two high speed burners and two
simmering burners which will accommodate pans
between 100mm (4”) and 240mm (91/2”) diameter. All
pans should be positioned centrally over the burners.
or fat.
2. Never leave oil or fat unattended during the heating
or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat. Frozen foods in
particular will cause frothing and spitting if added
too quickly.
5. Always keep the outside of the pan clean and free
from streaks of oil or fat.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the
lid and then raise it to its fully open position.
2. Press the ignition button and then push in and
turn the control knob of the chosen burner anticlockwise to the large flame symbol. Continue to
press the ignition button until the sparks light the
gas.
3. Turn the control knob anti-clockwise to reduce the
heat input. Only turn the control knob between the
large flame symbol and the small flame symbol
when adjusting the setting.
4. To turn off, turn the control knob fully clockwise to
the symbol O.
DO NOT
DO NOT
DO NOT
DO NOT
use the hotplate unless all pan supports
are in position.
use mis-shapen pans which may be unstable.
use round base woks directly on the pan
supports.
use the glass lid as a working surface.
Each burner is fitted with a spark ignitor for lighting the
gas. To ensure rapid lighting of the burners every time
they are used, the ignitors must be kept clean and dry.
Remove any food spillage or cleaning materials from
the ignitor using a small nylon brush such as a tooth
brush. Access to the ignitor can be achieved by lifting
off the loose burner parts carefully when the burners
are cool.
When the hotplate burner bodies and caps are
removed for cleaning, be careful not to drop any food
particles or cleaning materials into the burner bases, to
avoid the possibility of blocking the gas jets.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp
cloth to extinguish the fire. Do not use water or a
fire extinguisher as the force of it may spread the
burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving
it.
Models with Hob Gas Burner Safety Devices to
Prevent Leaks
These models can be identified by the presence of the
device itself.
! Since the hob burners are equipped with a safety
device, you must hold the control knob in for about 3-7
seconds after the burner has been lighted to allow the
gas to pass until the safety thermocouple has heated.
HOB GAS BURNER
SAFETY DEVICE
Practical Advice on Using
the Burners
ELECTRONIC
LIGHTING DEVICE
To use the burners as
efficiently as possible, some basic guidelines should
be followed:
• Use cookware that is the right size for each burner
(see table) in order to prevent the flame from
spreading beyond the bottom of the cookware.
• Only use cookware with flat bottoms.
• As soon as the boiling point is reached, turn the
knob to the lowest setting.
• Always use lids with pots and pans.
If aluminium based pans are used, a silvery deposit
may appear on the top edge of the pan support
fingers. See ‚Care and Cleaning’ section for cleaning
information.
Burner
ř Cookware diameter (cm)
Fast (R)
20 -22
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
Semi Fast (S)
16 - 20
1. Never fill chip pans more than one third full with oil
Auxiliary (A)
10 - 14
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
11
GB
Grill
GB
GRILLING MUST BE DONE WITH THE GRILL DOOR
OPEN.
CONTROL KNOBS MAY BECOME HOT DURING
GRILLING.
CAUTION: ACCESSIBLE PARTS WILL BECOME HOT
WHEN THE GRILL
IS USED - CHILDREN SHOULD BE KEPT AWAY.
Relighting‘ the burner
To operate the grill proceed as follows:
The grill pan handle is detachable from the pan to
facilitate cleaning and storage. Fix the pan handle
securely before use:
 Open the grill door and remove the grill pan.
 Press the ignition button and then push in and turn
the grill control knob anti-clockwise to the large
flame symbol. Continue to press the ignition button
until the spark lights the gas.
Turn the control knob anti-clockwise to the desired
setting. There is a delay of about six seconds whilst
the safety device operates before the burner comes
on full. Only turn the control knob between the large
flame symbol and the small flame symbol when
adjusting the setting.
 To turn off, turn the control knob fully clockwise to
the symbol O
! When using the grill, the
oven door must be left
open by positioning the
deflector “B” between
control panel and
deflector “A” to prevent
the cooker knobs from
overheating.
A
In the event of the burner flames being accidentally
extinguished, turn off the burner control and do not
attempt to re-ignite the burner for at least one minute.
Fixing the Grill PanHandle
1. Fit the handle to the grill pan so that the external
‘hooks’ embrace the edge of the pan (fig. 1)
2. Make sure that the middle part of the handle fits
exactly the protruding support of the pan
(fig .2) and holds the pan from the bottom.
The food must be placed on the rack in the grill pan.
Position the grill pan on top of the oven rack. The best
results are achieved by placing the oven rack on the
uppermost shelves. Pouring a little water into the grill
pan will make the collection of grease particles more
efficient and prevent the formation of smoke.
B
1
2
Slide the grill pan along the runner towards the rear of
the grill compartment until it stops. An odour may be
noticed when first using the grill - this schould cease
after a short period of use.
Grill can be started from cold but for the best result
preheat for approximately five minutes. Most cooking is
done with the heat on full, but it may be necessary after
sealing the food to reduce the heat as required.
For au gratin dishes eg. Macaroni Cheese and
meringue toppings eg. Baked Alaska place the dish
on the floor of the grill compartment. The base of the
grill pan can be used for warming fruit garnishes on the
reduced setting.
DO NOT
cover the grill pan or grid with
aluminium foil as this can hold fat, intensify the heat
and create a fire hazard.
12 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Oven
The main oven is fitted with a safety device that will
cut off the gas supply to the burner if the flame has
been extinguished for any reason. Each time the main
oven is used, the safety device has to be activated by
pushing and holding in the control knob for 3 seconds
after the gas has lit.
The oven has different heat zones - the thermostat
settings refer to the temperature on the middle shelf
position; above this shelf it is hotter and below it is
cooler. Two shelves provide five possible cooking
levels enabling full use of the different temperatures
inside the oven.
The maximum size of baking tray that should be used
is 325mm x 350mm (13” x 14”).
TO USE THE MAIN OVEN
1. Place the oven shelves in the appropriate positions
(refer to cooking charts).
2. Press in the ignition button and then push in and
turn the control knob fully anti-clockwise. Continue
to push in the control knob for a further 3 seconds
after the gas has lit to allow time for the safety
device to operate. If the burner extinguishes when
the control knob is released, repeat the procedure
ensuring the control knob is fully depressed and
allowing more time for the safety device to operate.
3. Turn the control knob clockwise to the required
setting (refer to cooking chart).
4. To turn off, turn the control knob fully clockwise the
the symbol O.
If for any reason the oven burner has not lit after 15
seconds, turn the control knob to the OFF position.
Leave the main oven door open and wait for at least 1
minute before attempting to light the burner again.
Never place dishes over the burner.
An odour may be noticed when first using the oven this should cease after a short period of use.
RELIGHTING THE BURNER
In the event of the burner flames being accidentally
extinguished, turn off the burner control and do not
attempt to re-ignite the burner for at least one minute.
COLD START COOKING
Anything requiring long slow cooking such as
casseroles and rich fruit cakes can be put into a cold
oven. Satisfactory results can also be obtained with
creamed mixture, rich pastries or yeast mixtures, but
for perfection we recommend preheating the oven
for about 15 minutes at the gas mark you require for
cooking.
ROASTING OF LARGE POULTRY
The maximum weight of poultry that can be
accommodated is 11.5kg (25 lbs) of suitable shape.
It is important to check that the bird DOES NOT
overhang the burner at the back of the oven.
GB
STORAGE AND RE-HEATING OF FOOD
It is vitally important to strictly adhere to the basic
principles of food handling and hygiene to prevent the
possibility of bacterial growth.
1. If food is to be frozen or not served immediately,
cool it in a clean container as quickly as possible.
2. Completely thaw frozen food in the refrigerator
before re-heating.
3. Re-heat food thoroughly and quickly either on the
hotplate or in a hot oven, Mk. 6, and then serve
immediately.
4. Only re-heat food once.
‚COOK CHILL’ DISHES
These should always be placed in a pre-heated oven
ideally on the first or second shelf position. Follow the
packet instructions for cooking time.
ALUMINIUM FOIL
If using Aluminium Foil:
1. Remember that it is important to increase the cooking time by one third.
2. Never allow the foil to touch the sides of the oven.
3. Never cover the oven interior with foil.
4. Never cover the oven shelves with foil.
The oven temperature control marking are gas marked
0 to 9. The equivalent degrees Celsius (sometimes
called Centigrade) and degrees Fahrenheit are shown
below as a guide.
MAIN OVEN
Gas Mark
(Centre Oven Temperature)
Celisus
°C
Fahrenheit °F
1
120
250
2
150
300
3
175
350
•
195
385
MAIN OVEN
Gas Mark
(Centre Oven Temperature)
Celsius
°C
Fahrenheit °F
5
210
410
•
220
430
7
230
445
•
240
465
9
245
475
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
13
Oven Cooking Chart
GB
The following times and setting are for guidance only. You may wish to alter the setting to give a result more
to your satisfaction. When a different setting to that shown below is given in a recipe, the recipe instructions
should be followed. Allow 15 minutes preheat for best results. Always turn the thermostat knob to Mark 9
before selecting the appropriate gas Mark. Shelf position 1 is the highest.
Food
Gas
Mark
Shelf
Position
Approx. Cooking Time and Comments
3 or 4
4
25-60 mins. depending on recipe
Beef
4 or 5
4
Ham
5
4
Lamb
Pork
Chicken
Duckling & Goose
Turkey
Casseroles
5
5
5
5
4 or 5
3
4
4
4
4
4 or 5
3or4
25-30 mins per 450g (1 Ib) + 25 mins. extra
40 mins per 450g (1 Ib) covered in foil plus 40 mins.
extra
30 mins per 450g (1 Ib) + 30 mins extra
40 mins per 450g (1 Ib) + 40 mins extra
25 mins per 450g (1 Ib) + 25 mins extra
25 mins per 450g (1 Ib) + 25 mins extra
15-20 mins per 450g (1 Ib) + 20 mins
2-6 hrs. depending on cut of meat
4 or 5
3
1½ - 3 hrs. until soft, depending on size
Milk Puddings (500ml/1 pt)
3
4
Baked Custard (500ml/1 pt)
Baked Sponge Puddings
Baked Apples
Meringue Topped Puddings
//
Apple Tart (1 x205mm/8 )
Fruit Crumble
Cakes, Pastries & Biscuits
Small Cakes 2 trays
1 tray
Victoria sandwich (2 x 7")
Swiss Roll (3 egg quantity)
Meringues
Christmas cake (1 x 205mm / 8")
Madeira cake (1 x 180mm / 7")
Rich Fruit cake (1 x 180mm / 7")
Scones
Shortbread (1 x 180mm / 7")
Biscuits
Shortcrust Pastry
Rich Short Crust
Flaky/Puff Pastry
Choux Pastry
3
4
3
1
6
5
4
3
3
3or4
2
2
1¾-2½ stand dish on baking tray and started with
warm milk
45-60 mins. bain-marie
40-50 mins
30-45 mins depending on type and size of apples
15 mins or until "tinged" with brown
45-60 mins
35 -45 mins
5
5
4
5
1
2
4
2
7
2
4
6
5
7
6
2 and 4
2
2 and 4
2
3
3
4
4
1 and 3
3
1 and 3
2
1 and 3
2
2
15-25 mins.
15-22mins.
20-30 mins
15-20 mins.
2-3 hrs
Time depending on recipe
1¼-1½ hrs.
Time depending on recipe
10-20 mins.
55 -65 mins.
10-20 mins.
15 - 60 mins depending on use.
20-30 mins.
10-30 mins.
20-30mins.
7
2 and 4
20-30 mins.
7
7
1
2
30-40 mins
20-30mins
Fish
Oily and white fish
Meat and Poultry
Vegetables
Baked jacket potatoes
Puddings
Yeast Mixtures
Bread - rolls
Miscellaneous
Yorkshire Pudding:- large
individual
When baking with two trays or tins on two levels, the
top tray is removed first and the lower tray moved up
to the top position for a few minutes longer.
Soft Margarine Use the oven settings recommended by the margarine
manufacturer and not those indicated on the cooking
chart.
14 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Care and Cleaning
Grill
Remove the grill pan and the wire grid food support,
it is best to wash these items immediately after use to
prevent stains from being burnt on when used again.
Wipe out the Grill compartment, use a fine steel wool
soap pad to remove stubborn stains from the grill
runners and the floor of the compartment. Wipe over
the control panel with a damp cloth and polish with a
dry cloth.
Control Panel
Do not use cream cleaners, oven cleaners or aerosols,
scouring pads or abrasive powder for cleaning the
plastic knobs as damage will occur.
Decorative Trims
It is advisable to clean the decorative trims regularly
to prevent any build up of soiling. The recommended
method of cleaning is to wipe over the trims with a soft
cloth wrung out in warm water or mild non-abrasive
cleaner. (If in doubt try the cleaner on a small area of
trim which is not noticeable in normal use). Then, after
wiping with a cloth wrung out in clear water, dry with a
soft clean cloth.
Doors
Wipe over the outer door glass panels with a cloth
wrung out in warm soapy water, then after wiping with
a cloth wrung out in clear water, dry with a soft clean
cloth. Ensure that glass doors are not subjected to any
sharp mechanical blows.
Glass Inner Door Panel (where fitted) *
Open the door fully and unscrew the two screws
securing the glass panel, taking care not to allow the
glass to fall. The glass panel may now be washed at
the sink. Stubborn stains can be removed by using
a fine steel wool soap pad. Ensure the glass panel is
not subjected to any sharp mechanical blows. Take
particular care not to damage the inner surface which
is coated with a heat reflective layer. After cleaning,
rinse and dry with a soft cloth. For slight soiling the
inner glass panel may be cleaned, while still warm,
without removing it from the door.
Warning: Oven must not be operated with inner door
glass removed.
Take care during cleaning not to damage or distort
the door seals. Do not lift the door seal from the oven
chassis, if necessary remove the seal by carefully
unhooking the corner clips.
Take care that the rating label edges are not lifted
during cleaning, and furthermore that the lettering is
not blurred or removed.
Top Cavity
Remove the rod shelves and grill pan. Use a fine steel
wool soap pad to remove stubborn stains from the rod
shelves, grill pan and the floor of the oven. Clean the
glass part of the oven door using a sponge and a nonabrasive cleaning product, then dry thoroughly with a
soft cloth. Do not use rough abrasive material or sharp
metal scrapers as these could scratch the surface and
cause the glass to crack.
Main Oven Cleaning
Main oven is fitted with “Stay Clean” panel.
‚Stay Clean’ panels are covered with a special enamel
which absorbs cooking soils. At higher temperatures
the soiling is slowly destroyed. In most cases normal
cooking at higher temperatures will permit this cleaning
to take place automatically. However, if higher cooking
temperatures are not used regularly then it may be
necessary, in order to prevent heavy soiling, to run
the oven at maximum temperature for at least two
hours, from time to time. The ‚Stay Clean’ panel can
be washed in warm soapy water followed by rinsing in
clear water. Dry well with a soft cloth.
NOTE: Do not use enzyme washing powder, harsh
abrasives or chemical oven cleaners of any kind.
Oven Shelf Supports
The shelf supports are removable and dishwasher
safe.
To remove hold the support at the front and pull away
from the oven side, this can then be cleaned in a sink
or a dishwasher. When removed it allows access to
the oven side, which can be cleaned with warm soapy
water.
To refit the support, insert the longer leg into the rear
fixing hole and push in the front leg.
Replacing the Battery
The battery is not covered bye the guarantee. Use an
alkaline AA battery. The battery holder is located in the
plinth panel below the oven door. Open the oven door
fully. Press the tag on the left hand side of the battery
holder/cover and withdraw it just enough to get access
to the battery. Fit the new battery with the end marked
“+” on the same side of the battery holder as the red
lead. Replace the battery holder by pushing it firmly
into the hole in the plinth.
* (only available on certain models)
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
15
GB
Cooking Results Not
Satisfactory?
GB
Problem
Check
Grilling
Uneven cooking front to
back
Ensure that the grill pan is positioned centrally below
the grill element.
Fat splattering
Ensure that the grill is not set to too high a temperature.
Oven Baking
Uneven rising of cake
Ensure that the oven shelves are level by using a spirit
level on the rod shelf and adjusting, using suitable
packing e.g. wood, under the feet of the appliance. This
should be checked both left to right and front to back.
Ensure that the food is positioned centrally in the oven.
Sinking of cakes
The following may cause cakes to sink:
1. Cooking at too high a temperature.
2. Using normal creaming method with soft margarine.
Over/Under cooking
Fast/Slow cooking
Refer to the cooking times and temperatures given in
the oven temperature charts, however, it may be
necessary to increase or decrease temperatures by
10°C to suit personal taste.
Do not use utensils greater than 2Ľ ins in height.
16 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Something Wrong
with your Cooker?
Before contacting your Service Centre or Installer,
check the problem guide below, there may be
nothing wrong with your cooker.
Problem
Ignition does not work
GB
Check
If all burners fail to ignite:
Check that sparks appear at the burners;
A clicking noise should be heard.
If only one burner fails to ignite
Check that the burner is dry and that spillage of food or
cleaning fluid remains are not affecting the Ignitor or burner
ports.
Hotplate Burner
Hob Top
Clean away any debris with a dry nylon brush such as an
old dry toothbrush.
If a wire wool pad has been used for cleaning around the
burner ensure the Ignitor is free from any stray strands.
Any water on the burner should be dried with a cloth or
kitchen towel.
On the hotplate make sure that all burner
parts are correctly seated
Burner Ports
Oven or Grill will not stay lit
when the control knob is released
Ignitor
For correct ignition of oven/grill burners press the ignition button
and then push in and turn control knobs anti-clockwise.
Continue to press the ignition button until the spark lights the gas.
Once alight release the ignition button and continue to hold the
control knob in for a further 6 to 10 seconds.
Then release the control knob and set to the required temperature.
The flame should now stay alight.
If the flame does not hold and goes out wait 30 seconds and try
again
Oven Temperature seems too
high or too low
Oven does not cook evenly.
Check that the temperature has been set in accordance with
the temperature charts. It may be necessary to increase or
decrease the recommended temperature by 10 C to suit your
taste
Check the temperature and shelf position are as recommended
in the temperature charts
Check that the Utensil being used in the oven allow sufficient
air flow around them.
Hotplates are slow to boil or will
not simmer
Odour or smoke when using your new cooker
Condensation / Steam in the Oven After Use
Condensation on the Wall at the Rear of the Cooker
Check that the cooker is level.
Check that your pans conform to the recommendations in
these instructions.
This is normal and should cease after a short period.
Condensation and steam is a by product of cooking food
with a water content.
To help minimise always:
A) Try to avoid leaving food in the oven to cool after being cooked
B) Use a coved Utensil wherever possible
Steam and/or condensation may appear from the vent at the rear of
the appliance when using an oven, particularly when cooking foods
with a high water content (Such as Oven Chips or Chicken).
This is normal and any excess should be wiped off
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
17
GB
Disposal of your product
To minimise the risk of injury to children please dispose
of your product carefully and safely. Remove all doors
and lids. Remove the mains cable (where fitted) by
cutting off flush with the appliance and always ensure
that no plug is left in a condition where it could be
connected to the electricity supply.
To help the environment, Local Authority instructions
should be followed for the disposal of your product.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of
the materials they contain and reduce the impact on
human health and the environment.
The crossed out „wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose
of the appliance it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
Respecting and conserving the
environment
• Whenever possible, avoid pre-heating the oven
and always try to fill it. Open the oven door as little
as possible because heat is lost every time it is
opened. To save a substantial amount of energy,
simply switch off the oven 5 to 10 minutes before the
end of your planned cooking time and use the heat
the oven continues to generate.
• Keep gaskets clean and tidy to prevent any door
energy losses
• If you have a timed tariff electricity contract, the “delay
cooking” option will make it easier to save money by
moving operation to cheaper time periods.
• The base of your pot or pan should cover the hot plate.
If it is smaller, precious energy will be wasted and
pots that boil over leave encrusted remains that can
be difficult to remove.
• Cook your food in closed pots or pans with well-fitting
lids and use as little water as possible. Cooking with
the lid off will greatly increase energy consumption
• Use purely flat pots and pans
• If you are cooking something that takes a long time,
it's worth using a pressure cooker, which is twice as
fast and saves a third of the energy.
18 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Guarantee
GB
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be
defective because of either workmanship or materials, we will, at our discretion, either repair
or replace the appliance at no cost to you.
The guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.
- The appliance is only used on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled or otherwise interfered
with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN
COMMERCIAL OR NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is
conditional on you registering your appliance with us and the parts being fitted by one of our
authorised engineers. There will be a charge for our engineer’s time. To activate the extra
parts warranty on your appliance, simply call our registration line on 08448 24 24 24 (ROI 01
230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the
expense of repair bills for the life of your policy. To find the ideal plan for you please call our
advice line on 08448 226 226 (ROI 01 230 0233)
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance
if you experience any technical difficulties within the first 90 days of ownership.
Simply call our Hotpoint Service Hotline on 08448 224 224 (ROI 0818 313 413) for telephone
assistance, or, where necessary, to arrange for an engineer to call.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
19
Indesit Company S.P.A.
Viale Aristide Merloni,47
60044 Fabriano (AN)
www.hotpoint.co.uk
GB
XEROX FABRIANO
04/2014 - 195122670.00
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working
life than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled telephone
advisors and 1100 fully qualified engineers on call to ensure you receive fast, reliable, local
service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
www.hotpoint.co.uk
Please note: Our advisors will require the following information:
Model number
Serial number
Parts & Accessories
We supply a full range of genuine replacement parts as well as accessory products that
protect and hygienically clean your appliance to keep it looking good and functioning
efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your FREE 5 year
parts guarantee you must register your appliance with us.
UK 08448 24 24 24
Republic of Ireland: 01 230 0800
www.hotpointservice.co.uk
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves
the right to use quality, recycled components to keep down customer costs and minimise
material wastage.
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17
20 PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24