installation instructions

Illuminated Valve Cover Conversion Kit
INSTALLATION INSTRUCTIONS
SAFETY INSTRUCTIONS
! WARNING:
Before starting installation, read and understand all safety label and warnings on the machine. Also review and
understand all safety instructions in the owners, installation and service manuals.
Failure to comply could result in serious injury, death or damage to the equipment.
QUALIFIED SERVICE PERSONNEL
! WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.
All wiring and plumbing must conform to national and local codes. Failure to comply could
result in serious injury, death or equipment damage.
SAFETY PRECAUTIONS
This unit has been specifically designed to provide protection against personal injury. To ensure continued
protection observe the following:
! WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
! CAUTION:
Always be sure to keep area around the unit clean and free of clutter.
Failure to keep this area clean may result in injury or equipment damage.
CO2 (CARBON DIOXIDE) WARNING
CO2 displaces oxygen. Strict attention MUST be observed in the prevention of CO2 gas leaks in the entire CO2
and soft drink system. if a CO2 gas leak is suspected, particularly in a small area, IMMEDIATELY ventilate the
contaminated area before attempting to repair the leak. Personal exposed to high concentrations of CO2 gas
experience tremors which are followed rapidly by loss of consciousness and DEATH
Revision Date: March 28, 2017
© 2017, Cornelius Inc. All Rights Reserved.
www.cornelius.com
-1-
Revision: A
Publication Number:629097630INS
Illuminated Valve Cover Conversion Kit
ILLUMINATED VALVE COVER CONVERSION
KIT
Part Number
Description
QTY
620065122
Cover Assembly SFV1 Illum Front Cover
1
620065009
Harness Assembly UF/SF Illum Valve
1
Installation Manual SFV1 Illuminated Valve
1
Kit Water Lever Extension
1
629097630INS
859000142
NOTE: For U.S & Canada Decals contact CCP.
1.
Remove front cover from valve
Figure 1
2.
Remove back cover from valve
Figure 2
Publication Number: 629097630INS
-2-
© 2017 Cornelius Inc. All Rights Reserved
Illuminated Valve Cover Conversion Kit
3.
Disconnect valve from dispenser harness
Figure 3
4.
Remove valve assembly from back block
Figure 4
5.
Disconnect harness from dispense switch
Figure 5
© 2017, Cornelius Inc. All Rights Reserved.
-3-
Publication Number:629097630INS
Illuminated Valve Cover Conversion Kit
6.
Figure 6
Disconnect harness from valve solenoid
Figure 7
Publication Number: 629097630INS
-4-
© 2017 Cornelius Inc. All Rights Reserved
Illuminated Valve Cover Conversion Kit
7.
Connect harness 620065009 to dispense
switch
Figure 8
Figure 9
© 2017, Cornelius Inc. All Rights Reserved.
-5-
Publication Number:629097630INS
Illuminated Valve Cover Conversion Kit
8.
Connect harness 620065009 to the solenoid
Figure 10
Figure 11
Publication Number: 629097630INS
-6-
© 2017 Cornelius Inc. All Rights Reserved
Illuminated Valve Cover Conversion Kit
9.
Remove optional water lever and retention
screw from valve body.
Figure 12
10. Install water lever extension kit 859000142
using the screw removed in step # 9
Figure 13
NOTE: Step 9 and 10 are only for valves containing the optional water lever.
© 2017, Cornelius Inc. All Rights Reserved.
-7-
Publication Number:629097630INS
Illuminated Valve Cover Conversion Kit
11. Re-install valve to unit back block
Figure 14
12. Re-install valve back cover
Figure 15
Publication Number: 629097630INS
-8-
© 2017 Cornelius Inc. All Rights Reserved
Illuminated Valve Cover Conversion Kit
13. Connect Illuminated cover
620065122 to valve harness
Figure 16
14. Install illuminated cover to valve
Figure 17
© 2017, Cornelius Inc. All Rights Reserved.
-9-
Publication Number:629097630INS
Illuminated Valve Cover Conversion Kit
ON
OFF
Figure 19
Figure 18
•
Access downward lighting switch by removing access cover on back of module.
•
To turn “ON” the downward lighting place the selector switch in the right position.
•
To turn “OFF” the downward lighting place the selector switch in the left position.
Figure 20
Publication Number: 629097630INS
- 10 -
© 2017 Cornelius Inc. All Rights
Illuminated Valve Cover Conversion Kit
• For U.S and Canada Custom Decals contact CCP.
• For all other countries you may source from your local Coke approved supplier using the below material
specifications.
•
0.010 Inch clear polycarbonate with white diffuser. 3M468MP adhesive on back surface with removable
protective backing paper.
© 2017, Cornelius Inc. All Rights Reserved.
- 11 -
Publication Number:629097630INS
Download PDF