PREPARATION FOR USE :
• Open the battery cover and insert a 9V – PP3 battery
(not included).
• Use the switch inside the battery compartment to switch
the display from ˚C to ˚F
• Close the compartment again.
IMPORTANT:
• Do not immerse the device. Clean only the device
exterior, using a soft cloth moistened with soapy
water.
Soapy
Water
IR measurement
cell
Laser
Measuring
point
• The ratio – target dimensions/measuring distance
is set at 8:1. This means that an area measured at
80cm distance will have a diameter of 10cm.
Battery Cover
2.5cm
5cm
10cm
D:S = 8:1
+-
S
9V
Batte
ry
20cm
40cm
D
SCREEN DISPLAY
INSTRUCTION AND SAFETY
MANUAL
Original instructions
I.R. THERMAL DETECTOR DEVICE
WITH LASER POINTER
Thank you for choosing a
product.
You will find it is very useful for your
installation works or measurements.
In order to correctly use your thermal
detector device with laser pointer, it is
essential that you take the time to read
these instructions carefully. They will
provide you with
essential information
about the device’s functions and how to
maintain the product correctly.
Please retain this manual in case you need
to refer to it at a later date.
WARRANTY
This product is guaranteed for 2 years from the date
of purchase.
The warranty covers device breakdown and
malfunctions when the device is used in compliance
with the manner intended and the instructions for use
contained in the manual.
To be covered by the warranty, proof of purchase is
required (till receipt or invoice) and the product must
be complete.
The warranty does not cover wear and tear through
normal use, lack of maintenance, negligence,
immersion or inappropriate use (impact damage,
non-respect for electrical supply recommendations,
storage, usage conditions, etc).
Also excluded from the warranty are harmful
consequences due to dismantling or modifying the
device.
Press
briefly
80cm
Current
temp.
• Do not use the device near radio-frequency sources.
Max. temp.
Battery
level
Laser
pointer
TAKING MEASUREMENTS
1. Single measurement (HOLD mode)
- Point at the target to be measured,
if possible from a distance of 60cm
in order to reduce the diameter of
the area, then press the trigger once
and release again.
- The temperature will be displayed
on screen for 7 seconds.
2. Continual measurement (READ mode)
- Point at an area and press the trigger,
then move to another area while
keeping the trigger pressed down.
Move again if necessary.
- The maximum temperature measured
while scanning the areas is displayed
on the lower section of the screen.
If no difference in temperature is recorded, the
two temperatures displayed will be identical.
- The displays will be automatically cleared after
7 seconds.
Note:
From around a 5°C difference between ambient
temperature and the temperature of a wall or
opening there is over-consumption of energy.
Openings should therefore be isolated or equipped
with appropriate products.
• The normal function of the product may be
disturbed by Strong Electro Magnetic Interference.
If so, simply reset the product to resume normal
operation by following the instruction manual.
SPECIFICATIONS
•
•
•
•
Measuring type
Distance to spot ratio
Temperature range
Accuracy
:
:
:
:
•
•
•
•
•
•
•
Laser pointer:
Ambient Operating temperature
Response time (95%)
Spectral response
Emissivity
Re-actualisation
Relative humidity
:
:
:
:
:
:
•
•
•
•
•
Display resolution
Optical resolution
Display old
Battery icon
Power
:
:
:
:
:
Infrared transmitter
8:1
-20°C to +315°C
± 1,5°C (between 10° and 60°C) or
± 2˚C or 2% ≤ 10° and ≥ 60°C
± 3˚C from -20˚C to 0˚C
Red spot –ClassII laser product
0°C - 50°C
< 0,5sec.
7-18 µm
preset to 0,95
2 times/sec.
90% ± 5% RH non
condensing at 30°C
4 digits – 8mm- (0,1°C)
0,1°C
7 seconds
2h before out of use
1x 9V dry battery (not supplied)
RECOMMENDATIONS
WARNING
This infrared thermometer is equipped with a class 2
laser cell, manufactured in compliance with
international standards EN60825 – 1 January 2008.
Only qualified operators can install, adjust and test
this laser equipment.
Using the laser with magnifying-type optical
equipment or a telescope can be dangerous.
Children should not be allowed to use this device and
it should not be left such that they are able to.
The laser should be turned off at the same time the
measurement is taken.
Do not direct the laser beam towards the eyes.
CAUTION /
LASER
RADIATION
<1mW / 650 nm
2
EN 60825 - 1 January 2008
CAUTION/LASER RADIATION
DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
Titan Power Tools (UK) Ltd
Trade House, Mead Avenue, BA22 8RT
TTO369HTL
Alim.: 1 x 9V (PP3) 83-6
38-S07R000
For optimal precision, the device should be at least
60cm away from the target. Measurement precision
for greater distances could be affected by external
factors such as currents of hot or cold air, or
temperature variations from the same area, due to
an increase in the diameter of the long distance
target.
However, the area to be measured should be
greater than the diameter of the spot. If the target is
frosty, greasy or dirty, clean it before measuring.
In the event that ambient temperature measurements are out of range (0°C - 50°C), a fifteen minute
period of stabilisation may be required.
DECLARATION OF CONFORMITY
We, Titan Power Tools (UK) Ltd
Trade house, Mead Avenue, BA22 8RT
Declare, under our own responsibility, that the following device:
Product designation: I.R. THERMAL DETECTOR
DEVICE WITH LASER POINTER
TITAN model number TTO369HTL
Meets all the necessary requirements of the directives listed below:
Directive on electromagnetic compatibility, 2004/108/CE
EN 61000-6-3: 2007
EN 61000-6-1: 2007
Laser classification
EN 60825-1 January 2008
Authorised signatory and technical file holder
Date: 07/07/2010
Signature:________________
Made in PRC
Name / title: Peter Harries / Quality Manager
Titan Power Tools (UK)Ltd. Trade House , Mead Avenue ,BA22 8RT
85-638-S02-001
Download PDF