Installation Instructions
for Stacked Washer/Dryers
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.speedqueen.com
Part No. 804671ENR3
June 2016
WARNING
IMPORTANT: Purchaser must consult the local gas
supplier for suggested instructions to be followed if
the dryer user smells gas. The gas utility instructions
plus the SAFETY and WARNING note directly above
must be posted in a prominent location near the dryer
for customer use.
WARNING
Risk of fire. Highly flammable material.
WARNING
W881
Read all instructions before using unit.
•
WARNING
•
•
FOR YOUR SAFETY, the information in this manual
must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.
W033
WARNING
Installation of unit must be performed by a qualified installer.
Install clothes dryer according to manufacturer’s
instructions and local codes.
DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)
duct is installed, it must be of a specific type
identified by the appliance manufacturer as suitable for use with clothes dryers. Refer to section
on connecting exhaust system. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
W729R1
•
•
•
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
WARNING
To reduce the risk of severe injury or death, follow all
installation instructions. Save these instructions.
W894
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
W053
W052
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
This product uses FreeRTOS V7.2.0 (www.freertos.org).
3
Part No. 804671ENR3
The following information applies to the state of Massachusetts,
USA.
•
•
•
•
This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
This appliance must be installed with a 36 inch [910 mm]
long flexible gas connector.
A “T-Handle” type gas shut-off valve must be installed in the
gas supply line to this appliance.
This appliance must not be installed in a bedroom or bathroom.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4
Part No. 804671ENR3
Table of Contents
...............................................................................................................3
Dimensions............................................................................................. 6
Installation............................................................................................. 9
Before You Start............................................................................................. 9
Tools..........................................................................................................9
Parts Included............................................................................................. 9
Removing Dryer......................................................................................... 9
Reassembling Dryer.................................................................................... 9
Order of Installation Steps............................................................................9
Position Unit Near Installation Area............................................................... 10
Remove Shipping Materials........................................................................... 10
Connect Fill Hoses........................................................................................ 11
Water Supply Requirements........................................................................11
Connecting Hoses......................................................................................11
Risers....................................................................................................... 12
Connect Drain Hose to Drain Receptacle.........................................................12
Standpipe Installation................................................................................ 12
Wall Installation........................................................................................ 13
Laundry Tub Installation............................................................................ 13
Gas Dryers - Connect Gas Supply Pipe........................................................... 13
Electric Dryer Only - Connect Electrical Plug..................................................15
Earth/Ground Information.......................................................................... 15
Connecting Power Cord with Three-Wire Plug.............................................15
Connecting Power Cord with Four-Wire Plug.............................................. 17
Connect Dryer Exhaust System...................................................................... 19
Exhaust Direction......................................................................................20
Exhaust System.........................................................................................20
Position and Level the Unit............................................................................20
Wipe Out Inside of Washer and Dryer Drums.................................................. 22
Plug In the Washer and Dryer.........................................................................22
Electric Dryer........................................................................................... 22
Gas Dryer................................................................................................. 22
Washer..................................................................................................... 24
Check Installation......................................................................................... 25
Check Heat Source........................................................................................25
Electric Dryers.......................................................................................... 25
Gas Dryers................................................................................................26
Installer Checklist.................................................................................27
©
Copyright 2016, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5
Part No. 804671ENR3
Dimensions
Dimensions
Electric Models
C
G
F
D
A
E
L
B
H
M
J
Q
O
P
K
N
I
SWD1003N_SVG
A
* 66.06 in. [1678 mm]
B
* 56.97 in. [1447 mm]
C
23.5 in. [597 mm]
D
8.375 in. [213 mm]
E
24 in. [610 mm]
F
8 in. [203 mm]
G
15.4 in. [391 mm]
H
* 36.9 in. [938 mm]
I **
* 14.6 in. [371 mm]
J
* 32 in. [813 mm]
K
26.875 in. [683 mm]
L
* 46.62 in. [1184 mm]
M
* 78.17 in. [1986 mm]
N
2.04 in. [52 mm]
O
27.73 in. [704 mm]
P (with door closed)
1.5 in. [38 mm]
Q
* 13.1 in. [333 mm]
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6
Part No. 804671ENR3
Dimensions
* With leveling legs turned into base.
** For ADA compliance turn legs out from base 0.5 inches.
NOTE: Exhaust openings are 4 inch [102 mm] metal
ducting.
Gas Models
C
G
F
1
D
E
H
O
A
B
I
N
L K
S
Q
R
M
P
J
SWD1004N_SVG
1. 3/8 in. NPT Gas Connection
A
*66.06 in. [1678 mm]
B
*56.97 in. [1447 mm]
C
23.5 in. [597 mm]
D
8.375 in. [213 mm]
E
24 in. [610 mm]
F
8 in. [203 mm]
G
15.4 in. [391 mm]
H
2.3 in. [59 mm]
I
*36.9 in. [938 mm]
J **
*14.6 in. [371 mm]
K
*44.87 in. [1140 mm]
L
*32 in. [813 mm]
M
26.875 in. [683 mm]
N
*46.62 in. [1184 mm]
O
*78.17 in. [1986 mm]
P
2.04 in. [52 mm]
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7
Part No. 804671ENR3
Dimensions
Q
27.73 in. [704 mm]
R (with door closed)
1.5 in. [38 mm]
S
*13.1 in. [333 mm]
* With leveling legs turned into base.
** For ADA compliance turn legs out from base 0.5 inches.
NOTE: Exhaust openings are 4 inch [102 mm] metal
ducting.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8
Part No. 804671ENR3
Installation
Installation
Before You Start
WARNING
Tools
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
For most installations, the basic tools you will need are:
1
2 3
W299
4
5
Parts Included
An accessories bag has been shipped inside your unit. It includes:
6
•
•
•
•
•
•
•
11
7
9
10
8
Installation Instructions
Two User's Guides (one for washer and one for dryer)
Warranty Bond
Three screws (electric dryers only)
Two fill hoses with washers and filter screens
Four rubber feet
Beaded strap
Removing Dryer
Use the following steps if the installation requires removal of the
dryer. Two people are required to perform this task.
SWD1021N_SVG
1. Wrench
2. 1/4 inch Driver
3. Screwdriver
4. Level
5. Wood Block
6. Pliers
7. 5/16 Inch Socket Wrench
8. Gloves
9. Teflon Tape (Gas Models)
10. Duct Tape
11. Safety Glasses
1. Remove dryer front access panel.
2. Remove two screws holding control panel to control cabinet.
3. Remove two 7/16 inch screws and washers attaching dryer to
washer.
4. Tip dryer back and disconnect dryer control wire harness
from main dryer wire harness.
5. Slide dryer forward until rear leveling legs slide into notches
in the control cabinet.
6. Lift dryer and place it on a level surface.
Reassembling Dryer
Figure 1
1. Lift dryer and place it on top of washer so dryer leveling legs
sit in notches in control cabinet.
2. Slide dryer backward until mounting holes in base line up
with holes in front of security cabinet.
3. Reconnect dryer wire harness. If needed, refer to unit’s wiring
diagram.
4. Tip dryer and replace two 7/16 inch screws and washers holding dryer to washer.
5. Reattach the control panel to the control cabinet using two
screws.
6. Replace dryer’s front access panel.
NOTE: If the unit is delivered on a cold day (below
freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until
the unit has had a chance to warm up.
NOTE: Some moisture in the wash drum is normal. Water is used during testing at the manufacturer.
NOTE: This appliance is suitable for use in countries
having a warm, damp climate.
Order of Installation Steps
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9
Part No. 804671ENR3
Installation
The proper order of steps must be followed to ensure correct installation. Refer to the list below when installing your unit.
1. Position unit near area of installation.
2. Remove the shipping materials.
3. Connect the fill hoses.
4. Connect the drain hose to the drain receptacle.
5. For gas models only, connect the gas supply pipe. Check for
gas leaks.
6. For electric models only, connect the electrical cord.
7. Connect dryer to exhaust system.
8. Position and level the unit.
9. Wipe out inside of washer and dryer drums.
10. Plug in the washer and dryer.
11. Check installation.
12. Start and run the dryer in a heat setting to verify dryer is heating.
Position Unit Near Installation Area
Move unit so that it is within 4 feet [1.2 meters] of the desired
area of installation.
1. Remove two screws at bottom of front access panel. Rotate
bottom of panel out and remove panel.
FLW2378N_SVG
Figure 2
2. Remove two 9/16 inch bolts and washers holding shipping
brace to weight.
3. Remove two 9/16 inch bolts and washers holding shipping
brace to washer base and remove brace.
CAUTION
Washer and dryer are not designed to be operated as
separated, side-by-side units.
W187
The stack washer/dryer must be installed on a ground or basement floor, preferably concrete. If the flooring is wood construction, the flooring must meet a static load rating of 125 pounds
and a maximum dynamic load rating of 170 pounds per foot. If
the existing floor does not meet the dynamic load rating, the floor
must be re-enforced from below to meet the specification (maximum span = 16 feet, 2x10 joists, 16 inches on center, 1 inch sub
floor).
The stack washer/dryer must be installed on a smooth, non-slip
surface. Un-level tile and extremely slippery surfaces should be
avoided. Do not install the washer on carpeting, soft tile or other
weakly supported structures.
Failure to meet the minimum floor load and surface requirements
or installing the products on above ground floors can create different levels of vibration or movement that may appear like service is required. Speed Queen will not cover scheduled repair services where the installation requirements are not per specifications, nor can products be returned to the authorized dealer in
these cases.
FLW2296N_SVG1
Figure 3
4. Go to rear of washer and pull label from rear shipping bolts.
5. Remove two 9/16 inch bolts. Unscrew each bolt while applying forward pressure just until bolt stops unthreading. Work
each bolt and spacer out by hand using a circular motion.
NOTE: Avoid backing bolts out completely or
spacers might fall into cabinet.
Remove Shipping Materials
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10
Part No. 804671ENR3
Installation
Water Supply Requirements
Water supply faucets must fit standard 3/4 inch [19 mm] female
garden hose couplings. DO NOT USE SLIP-ON OR CLAMPON CONNECTIONS.
NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being
used.
FLW2297N_SVG1
Figure 4
6. Insert two plugs included in accessories bag into rear shipping
bolt holes.
Recommended cold water temperature is 50° to 75° Fahrenheit
[10° to 24° Celsius]. Recommended maximum hot water temperature is 125° Fahrenheit [51° Celsius]. Warm water is a mixture
of hot and cold water. Warm water temperature is dependent upon
the water temperature and the pressure of both the hot and cold
water supply lines.
WARNING
To prevent personal injury, avoid contact with inlet
water temperatures higher than 125° Fahrenheit [51°
Celsius] and hot surfaces.
W748
Maximum flow rate for all water temperatures is 2.5 gallons per
minute [9.46 liters per minute] ± 15%.
Water pressure must be a minimum of 20 to a maximum of 120
pounds per square inch [minimum of 138 to a maximum of 827
kPa] static pressure measured at the faucet.
FLW2358N_SVG
Figure 5
7. Replace front access panel.
8. Save all shipping materials. They must be reinstalled any time
washer is moved more than four feet.
IMPORTANT: Do not lift or transport unit from front
or without shipping materials installed. Refer to the
User’s Guide for proper instructions on reinstalling
the shipping materials.
Connect Fill Hoses
WARNING
W029
DO NOT COPY or TRANSMIT
Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could
clog the screens in the water mixing valve. This is especially important when installing your washer in a newly constructed or
renovated building. Build-up may have occurred during construction.
Connecting Hoses
Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used
for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for
such a period and before using the washer, turn on
all hot water faucets and let the water flow from each
for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not
smoke or use an open flame during this time.
© Copyright, Alliance Laundry Systems LLC -
NOTE: Water pressure under 20 pounds per square
inch [138 kPa] will cause an extended fill time in the
washer and may not properly flush out the detergent
dispenser.
1. Remove the two plain rubber washers and two filter screens
from the accessories bag.
2. Install them into each end of the fill hoses as shown in Figure
6 . The screen must be facing outward.
3. Screw hose couplings with the filter screens onto the water
faucets until they are finger-tight. Use the red color-coded
hose for the hot water connection and the blue color-coded
hose for the cold water connection.
4. Then, using a pliers, screw approximately 1/4 turn.
5. Screw hose couplings from other end of hoses onto the water
mixing valve until they are finger-tight. Make sure the red
color-coded hose from the hot water faucet goes to the water
11
Part No. 804671ENR3
Installation
mixing valve marked “H” and the blue color-coded hose from
the cold faucet goes to the valve marked “C”. Refer to Figure
Figure 6 .
6. Then, using a pliers, screw approximately 1/4 turn.
1
IMPORTANT: DO NOT cross thread or overtighten
couplings. This will cause them to leak.
7. Turn water on and check for leaks.
8. If leaks are found, turn off the water, unscrew hoses and reinstall them until there are no leaks.
IMPORTANT: Turn off water supply whenever there
will be an extended period of non-use.
4
1
COLD
2
HOT
3
2
W005I_SVG
8
1. Risers (Air cushions)
2. Water Supply Faucets
7
6
5
Figure 7
FLW2304N_SVG1
1.
2.
3.
4.
5.
6.
Filter Screen (Screen must be facing outward)
Fill Hose
Rubber Washer (Plain)
Cold Water Connection
Hot Water Connection
Install this end of hose to valve connections at rear of
washer.
7. Install this end of hose to water supply faucet.
8. Faucet
Figure 6
Connect Drain Hose to Drain Receptacle
Remove the drain hose from its shipping position on the rear of
the washer by unhooking the hose from the retainer clamp and by
removing the shipping tape.
Install the drain hose into the drain receptacle (standpipe, wall or
laundry tub) following the instructions below.
IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch [32 mm] outside diameter drain hose.
Drain Flow Rate
IMPORTANT:
Hoses and other natural rubber parts deteriorate after
extended use. Hoses may develop cracks, blisters or
material wear from the temperature and constant high
pressure they are subjected to.
Flow Rate
Drain Height
All hoses should be checked on a monthly basis for
any visible signs of deterioration. Any hose showing
the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years.
Risers
Risers (or air cushions) may have to be installed if the pipes
knock or pound when flow of water stops. The risers are more efficient when installed as close as possible to the water supply faucets. Refer to Figure 7 .
gallons per minute [liters per minute]
3 ft. [0.9 m]
8.6 [32.7]
5 ft. [1.5 m]
6.8 [25.9]
6 ft. [1.8 m]
6.0 [22.7]
7 ft. [2.1 m]
5.1 [19.5]
8 ft. [2.4 m]
4.0 [15.2]
Standpipe Installation
1. Place the drain hose into the standpipe.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12
Part No. 804671ENR3
Installation
2. Remove the beaded tie-down strap from accessories bag and
place around standpipe and drain hose and tighten strap to
hold hose to standpipe. Refer to Figure 8 . This will prevent
the drain hose from dislodging from drain receptacle during
use.
1
2
3
H023i_SVG
1
1. Drain Hose
2. Beaded Strap (tape if necessary)
3. Fill Hoses
Figure 9
3
2
SWD1010N_SVG
1. 24 to 36 in. [610 to 914 mm] Recommended Height
2. Beaded strap from accessory bag
3. Standpipe 2 in. [51 mm] or 1-1/2 in. [40 mm]
Laundry Tub Installation
For this type of installation, the drain hose MUST be secured to
the stationary tub to prevent hose from disloding during use. Refer to Figure 10 . Use the beaded strap (supplied in accessories
bag) to secure hose.
Figure 8
Wall Installation
For installations of this type, the drain hose MUST be secured to
one of the fill hoses using the beaded strap from accessories bag.
Refer to Figure 9 .
1
NOTE: End of drain hose must not be below 24 in. [610
mm].
2
SWD1011N_SVG
1. Drain Hose
2. Beaded Strap (tape if necessary)
Figure 10
Gas Dryers - Connect Gas Supply Pipe
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. 804671ENR3
Installation
WARNING
Natural Gas Altitude Adjustments
Altitude
Orifice Size
To reduce the risk of gas leaks, fire or explosion:
•
•
•
•
•
•
The dryer must be connected to the type of gas
as shown on nameplate located in the door recess.
Use a new flexible stainless steel connector.
Use pipe joint compound insoluble in L.P. (Liquefied Petroleum) Gas, or Teflon tape, on all pipe
threads.
Purge air and sediment from gas supply line before connecting it to the dryer. Before tightening
the connection, purge remaining air from gas line
to dryer until odor of gas is detected. This step is
required to prevent gas valve contamination.
Do not use an open flame to check for gas leaks.
Use a non-corrosive leak detection fluid.
Any disassembly requiring the use of tools must
be performed by a suitably qualified service person.
feet [m]
No.
Part
No.
inches [mm]
9000 [2740]
46
0.0810 [2.06]
503780
10,000 [3050]
47
0.0785 [1.99]
503781
Table 1
2. Remove the shipping cap from the gas connection at the rear
of the dryer. Make sure you do not damage the pipe threads
when removing the cap.
3. Connect to gas supply pipe using thread sealant or Teflon
tape. Torque 90 - 175 inch-pounds [10.2 - 19.7 Nm].
NOTE: When connecting to a gas line, an equipment
shut-off valve must be installed within 6 feet [1.8 m]
of the dryer. An 1/8 in. NPT pipe plug must be installed as shown for checking inlet pressure. Refer to
Figure 11 .
W316
1
1. Make certain your dryer is equipped for use with the type of
gas in your laundry room. Dryer is equipped at the factory for
Natural Gas with a 3/8 inch NPT gas connection.
5
NOTE: The gas service to a gas dryer must conform
with the local codes and ordinances, or in the absence of local codes and ordinances, with the latest
edition of the National Fuel Gas Code ANSI Z223.1/
NFPA 54 or the CAN/CSA-B149.1 Natural Gas and
Propane Installation Code.
Btu/ft3
2
3
4
MJ/m3],
Natural Gas, 1000
[37.3
service must be supplied
at minimum 5.0 inch water column pressure to maximum 10.5
inch water column pressure.
For proper operation at altitudes above 3000 feet [915 m] the natural gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 1 .
D233I_SVG
1. New Stainless Steel Flexible Connector – (Use design
CSA certified connector) Use only if allowed by local codes
2. 1/8 in. NPT Pipe Plug
3. Equipment Shut-Off Valve
4. Black Iron Pipe:
Shorter than 20 ft. [6.1 m] – Use 3/8 in. [9.5 mm] pipe.
Natural Gas Altitude Adjustments
Altitude
feet [m]
Orifice Size
No.
inches [mm]
Part
No.
3000 [915]
43
0.0890 [2.26]
503778
6000 [1830]
44
0.0860 [2.18]
58719
8000 [2440]
45
0.0820 [2.08]
503779
Table 1 continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Longer than 20 ft. [6.1 m] – Use 1/2 in. [12.7 mm] pipe.
5. 3/8 in. NPT Gas Connection
Figure 11
4. Tighten all connections securely but don't overtighten to avoid
breaking or bending the gas valve bracket. Turn on gas and
14
Part No. 804671ENR3
Installation
check all pipe connections (internal & external) for gas leaks
with a non-corrosive leak detection fluid.
WARNING
NOTE: The dryer and its appliance main gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psi [3.45 kPa]. Refer to Check
Heat Source.
To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local regulations as
might apply. It is the customer’s responsibility to
have the wiring and fuses installed by a qualified
electrician to make sure adequate electrical power is
available to the dryer.
NOTE: DO NOT connect the dryer to L.P. Gas Service
without converting the gas valve. Install L.P. Gas Conversion Kit 649P3, available at extra cost.
L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft.3 [93.1 MJ/m3], service must be supplied at 10 ± 1.5 inch water column pressure.
For proper operation at altitudes above 3000 feet [915 m] the L.P.
gas valve spud orifice size must be reduced to ensure complete
combustion. Refer to Table 2 .
L.P. Altitude Adjustments
Altitude
feet [m]
Orifice Size
No.
inches [mm]
Part No.
3000 [915]
55
0.0520 [1.32]
58755
8000 [2440]
56
0.0465 [1.18]
503786
Table 2
Electric Dryer Only - Connect Electrical
Plug
Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz, 3 or 4
wire electrical supply. Refer to serial plate for specific electrical
requirements.
W521
Earth/Ground Information
This dryer must be properly connected to protective earth/ground
metal, permanent wiring system; or an equipment-earth/ground
conductor must be run with the circuit conductors and connected
to the equipment-earth/ground terminal or lead on the dryer.
The dryer has its own terminal block that must be connected to a
separate branch, 60 Hertz, single phase circuit, AC (alternating
current) circuit, fused at 30 Amperes (the circuit must be fused on
both sides of the line). Electrical service for the dryer should be
of maximum rated voltage (208 or 240 Volt, depending on heating element) listed on the serial plate. Do not connect dryer to
110, 115, or 120 Volt circuit.
Heating elements are available for field installation in dryers
which are to be connected to electrical service of different voltage than that listed on serial plate, such as 208 Volt.
NOTE: Branch circuit wire size requirements to laundry
room outlet are shown in table below.
Wire Length
IMPORTANT: Use only a new U.L. listed No. 10 (copper
wire only) three or four conductor power supply cord
kit rated 240 Volts (minimum) 30 Amperes and labeled
as suitable for use in a clothes dryer.
NOTE: The wiring diagram is located in the control cabinet.
Wire
Less than 15 ft. [4.5 m]
Listed No. 10 AWG Copper
wire only
Longer than 15 ft. [4.5 m]
Listed No. 8 AWG Copper
wire only
Table 3
The power cord connection between wall receptacle and dryer
terminal block IS NOT supplied with dryer. Type of power cord
and gauge of wire must conform to local codes.
Connecting Power Cord with Three-Wire Plug
NOTE: Four-wire cord is required for new branch-circuit installations, mobile homes or where codes do not
permit grounding through neutral.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15
Part No. 804671ENR3
Installation
NOTE: The power cord is NOT supplied with the electric dryer. Type of power cord and gauge of wire must
conform to local codes and instructions. The method
of wiring the dryer is optional and subject to local code
requirements.
NOTE: Connect the dryer to the power supply with the
MAXIMUM RATED VOLTAGE listed on the serial plate.
NOTE: Use COPPER WIRE only.
Shorter than 15 ft. (4.5 m) – use 10 AWG
Longer than 15 ft. (4.5 m) – use 8 AWG
6
7
8
1
9
14
4
10
5
11
2
2
12
13
3
16
L1 L2
15
L1 L2
D816I_SVG
1. A typical 30-Amp Three-Wire Receptacle NEMA Type 10-30R
2. 120 ± 12 V.A.C.
3. 240 ± 12 V.A.C.
4. Intermediate Fuse Box (may be omitted if service entrance box is fused)
5. Wall Receptacle
6. Power Supply
7. 3-Wire Earth/Ground Neutral 120/240 Volt, 60 Hertz AC 1 Phase Service Entrance Switch Box (Refer to NOTE above)
8. 30 Ampere Fuses or Circuit Breaker
9. Neutral Wire
10. Metallic or Non-Metallic Sheathed Cable (Copper Wire Only)
11. Power Cord (Not supplied with dryer)
12. Neutral
13. Terminal Block in Dryer
14. Intermediate Shut-Off Box (may or may not be fused)
15. Direct Connection
16. Power Cord Connection
Figure 12
1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16
Part No. 804671ENR3
Installation
6. Secure the strain relief to the power cord, or wires, where they
enter the dryer cabinet.
7. Check the continuity of the earth/ground connection before
plugging the cord into an outlet. Use an acceptable indicating
device connected to the center earth/ground pin of the plug
and the green screw on the back of the cabinet.
8. Reinstall access cover and screw.
Connecting Power Cord with Four-Wire Plug
NOTE: Four-wire cord is required for new branch-circuit installations, mobile homes or where codes do not
permit grounding through neutral.
D695I_SVG
Figure 13
3. Use a strain relief and insert end of power cord through power
supply hole.
2
1
3
4
7
7
6
Figure 14
7
5
7
D696I_SVG
4. Use the three screws from the accessories bag to attach the
power cord wires to the terminal block. Refer to Figure 15 .
DRY2016N_SVG
3-Wire Connection
1.
2.
3.
4.
5.
6.
7.
1
2
Typical Four-Wire Receptacle
Power Cord – Not Supplied with Dryer
Strain Relief Nut
Strain Relief
0 V.A.C.
240 ± 12 V.A.C.
120 ± 12 V.A.C.
Figure 16
4
3
1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
DRY2508N_SVG
1.
2.
3.
4.
"L1" Terminal
Neutral Terminal
"L2" Terminal
Earth/Ground to Bulkhead
Figure 15
5. Using a screwdriver, tighten all screws firmly.
DRY2467N_SVG
IMPORTANT: Failure to tighten these screws firmly
may result in wire failure at the terminal block.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Figure 17
17
Part No. 804671ENR3
Installation
3. Remove earth/ground screw from earth/ground to neutral wire
and save for use in Step 5. Earth/ground to neutral wire will
be attached to the neutral terminal in Step 6.
4-Wire Connection
8
1
7
2
1
3
6
DRY2468N_SVG
1. Earth/Ground Screw
4
5
DRY2482N_SVG
Figure 18
1.
2.
3.
4.
5.
6.
7.
8.
4. Use a strain relief and insert end of power cord through power
supply hole.
Neutral Terminal
“L2” Terminal
Black
White
Earth/Ground
Red
“L1” Terminal
Earth/Ground to Neutral Wire
Figure 20
DRY2469N_SVG
1. Strain Relief
Figure 19
5. Attach power cord earth/ground (green) wire to rear bulkhead
using earth/ground screw removed in Step 3.
6. Use the three screws from the accessories bag to attach the remaining power cord wires to the terminal block as follows:
a. Red wire to “L1” terminal.
b. Black wire to “L2” terminal.
c. White wire to Neutral terminal.
NOTE: When installing the white wire, loop the free
eyelet end of the earth/ground to neutral wire (removed in Step 3) and attach along with the white
wire to the neutral (center) terminal on the terminal
block.
7. Using a screwdriver, tighten all screws firmly.
IMPORTANT: Failure to tighten these screws firmly
may result in wire failure at the terminal block.
8. Secure the strain relief to the power cord, or wires, where they
enter the dryer cabinet.
9. Check the continuity of the earth/ground connection before
plugging the cord into an outlet. Use an acceptable indicating
device connected to the center earth/ground pin of the plug
and the green screw on the back of the cabinet.
10. Reinstall access cover and screw.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18
Part No. 804671ENR3
Installation
Connect Dryer Exhaust System
WARNING
To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors.
W604
WARNING
To reduce the risk of fire and the accumulation of
combustion gases, DO NOT exhaust dryer air into a
window well, gas vent, chimney or enclosed, unventilated area, such as an attic, wall, ceiling, crawl
space under a building or concealed space of a
building.
1
SWD997N_SVG
1. Correct
2. Incorrect
W045
WARNING
Figure 21
This gas appliance contains or produces a chemical
or chemicals which can cause death or serious illness and which are known to the State of California
to cause cancer, birth defects, or other reproductive
harm. To reduce the risk from substances in the fuel
or from fuel combustion, make sure this appliance is
installed, operated, and maintained according to the
instructions in this manual.
W115
•
•
•
•
•
•
•
WARNING
To reduce the risk of fire, DO NOT use plastic or thin
foil ducting to exhaust the dryer.
W354
•
•
•
WARNING
•
To reduce the risk of fire, the exhaust duct and
weather hood MUST be fabricated of a material that
will not support combustion. Rigid or flexible metal
pipe is recommended for a clothes dryer.
W048
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
2
•
•
•
19
DO NOT use plastic, thin foil or type B ducting. Rigid metal
duct is recommended.
Locate dryer so exhaust duct is as short as possible.
Be certain old exhaust ducts are cleaned before installing your
new dryer.
Use 4 inch [102 mm] diameter rigid or flexible metal duct.
The male end of each section of duct must point away from
the dryer.
Use as few elbows as possible.
Use of duct tape or pop-rivets on all seams and joints is recommended, if allowed by local codes. DO NOT use sheet
metal screws or fasteners on exhaust pipe joints which extend
into the duct and catch lint.
Ductwork that runs through unheated areas must be insulated
to help reduce condensation and lint build-up on pipe walls.
In mobile home installations, dryer exhaust duct must be secured to mobile home structure.
Dryer exhaust duct MUST NOT terminate under mobile
home.
Exhaust duct must not be connected to any other duct, vent, or
chimney.
Dryer exhausts 220 cfm per unit (measured at back of dryer).
DO NOT install flexible duct in concealed spaces, such as a
wall or ceiling.
Static pressure in exhaust duct should not be greater than 0.6
inches water column [1.5 cm water column], measured with
manometer placed on exhaust duct 2 feet [610 mm] from dryer (check with dryer running and no load).
Part No. 804671ENR3
Installation
•
Exhausting dryer in hard-to-reach locations can be done by
installing 521P3 Flexible Metal Vent Kit (available as optional equipment at extra cost).
Sufficient make-up air must be supplied to replace the air exhausted by the dryer. The free area of any opening for outside
air must be at least 40 in.2 [1016 mm2] per unit.
Failure to exhaust dryer properly will void warranty.
A dryer will dissipate 60 Btu/ft2 [681,392 J/m2] of surface
area exposed to the conditioned air.
•
•
•
Dryer is shipped from factory ready for rear exhaust.
Exhausting the dryer through sides or bottom can be accomplished by installing a Directional Exhaust Kit, 528P3, available as
optional equipment at extra cost.
Exhaust System
For best drying results, recommended maximum length of exhaust system is shown in Table 4 .
NOTE: Venting materials are not supplied with the dryer (obtain locally).
To prevent backdraft when dryer is not in operation, outer end of
exhaust pipe must have a weather hood with hinged dampers (obtain locally).
IMPORTANT: DO NOT block the airflow at the bottom of
the dryer’s front panel with laundry, rugs, etc. Blockage
will decrease airflow through the dryer, thus reducing
the efficiency of the dryer.
NOTE: Weather hood should be installed at least 12 inches [305 mm] above the ground. Larger clearances
may be necessary for installations where heavy snowfall can occur.
Exhaust Direction
The dryer can be exhausted to the outdoors through the back, left,
right or bottom of the dryer. EXCEPTION: Gas dryers cannot be
vented out the left side because of the burner housing.
Weather Hood Type
Number of 90° Elbows
Recommended
Use Only for Short Run Installations
1
1
D673I_SVG
1. 4 in. [102 mm]
1
D802I_SVG
1. 2.5 in. [64 mm]
Maximum length of 4 in. [102 mm] diameter rigid metal duct.
0
65 feet [19.8 m]
55 feet [16.8 m]
1
55 feet [16.8 m]
47 feet [14.3 m]
2
47 feet [14.3 m]
41 feet [12.5 m]
3
36 feet [11.0 m]
30 feet [9.1 m]
4
28 feet [8.5 m]
22 feet [6.7 m]
Table 4
NOTE: Deduct 6 feet [1.8 m] for each additional elbow.
Position and Level the Unit
NOTE: The maximum length of a 4 in. [102 mm] diameter flexible metal duct must not exceed 7.87 ft. [2.4 m],
as required to meet UL2158, clause 7.3.2.A.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20
Part No. 804671ENR3
Installation
WARNING
Dryer and Exhaust Duct Clearances
Units elevated above floor level must be anchored to
that elevated surface, base or platform. The material
used to elevate the unit should also be anchored to
the floor to ensure that the unit will not walk or that
the unit can not be physically pulled, tipped or slid
from its installed position. Failure to do so may result in conditions which can produce serious injury,
death and/or property damage.
W307
Area
2.
3.
4.
D
E
E
Minimum
Clearance
* Rear clearance is minimum. 6 inches [152 mm] are
recommended when venting through rear of unit.
1. Position unit so it has sufficient clearance for installation and
servicing.
C
Description
5.
NOTE: Use of the dispenser drawer or unit doors as
a handle in the transportation of the unit may cause
damage to the dispenser or doors.
Place unit in position on a solid, sturdy and level floor. Installing the unit on any type of carpeting, soft tile or other weakly
supported structures is not recommended.
Place a level on the raised portion of cabinet top and check if
the unit is level from side to side and front to back.
If unit is not level, tilt unit to access the front and rear leveling legs. For easier access to leveling legs, prop up unit with a
wooden block.
Loosen 7/8 in. locknut and adjust legs by screwing into or out
of unit base until the unit is level from side to side and front
to back (using a level). Unit should not rock.
NOTE: Leveling legs can also be adjusted from inside the unit using an adjustable wrench.
6. Tighten the locknuts securely against the unit base. If the
locknuts are not tight, unit will move out of position during
operation.
A
B
SWD1006N_SVG
NOTE: DO NOT slide unit across floor if the leveling
legs have been extended. Legs and base could become damaged.
7. Remove rubber feet from accessories bag and place on all
four leveling legs.
8. Verify that unit doesn’t rock.
NOTE: Shaded areas indicate adjacent structure.
Dryer and Exhaust Duct Clearances
Area
Description
Minimum
Clearance
A
Left Dryer Side
0 in. [0 mm]
B
Right Dryer Side
1 in. [25 mm]
C
Dryer Top
6 in. [152 mm]
D*
Dryer Rear
4 in. [102 mm]
E
Exhaust Duct
2 in. [51 mm]
Clearance to
Combustible Materials
Table continues...
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
21
Part No. 804671ENR3
Installation
1
6
5
2
4
SWD1013N_SVG
3
SWD1029N_SVG
1.
2.
3.
4.
5.
6.
Level
Wood Block
Rubber Foot
Leveling Leg
Locknut
Unit Base
Figure 24
Plug In the Washer and Dryer
Electric Dryer
Connect the dryer to an electrical power source. Refer to Connect
Electrical Plug section for information on connecting power cord.
Figure 22
Connect to 30 Amp Circuit
Wipe Out Inside of Washer and Dryer
Drums
IMPORTANT: Prior to first wash, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside the drums.
D275I_SVG2
Figure 25
Gas Dryer
Dryer requires 120 Volt, 60 Hertz electrical supply and comes
equipped with a 3-prong earth/ground plug. Refer to serial plate
for specific electrical requirements.
NOTE: The wiring diagram is located in the control cabinet.
SWD1012N_SVG
Figure 23
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22
Part No. 804671ENR3
Installation
Plug Cord Into Separately Fused 15 Amp Circuit
WARNING
To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local regulations as
might apply. It is the customer’s responsibility to
have the wiring and fuses installed by a qualified
electrician to make sure adequate electrical power is
available to the dryer.
2
3
1
8
6
7
W521
4
When plugging in the dryer:
•
•
•
•
5
DO NOT overload circuits.
DO NOT use an extension cord.
DO NOT use an adapter.
DO NOT operate both a washer and a gas dryer on the same
circuit. Use separately fused 15 Amp circuits.
The dryer is designed to be operated on a separate branch, polarized, three-wire, effective earth/ground, 120 Volt, 60 Hertz, AC
(alternating current) circuit protected by a 15 Ampere fuse,
equivalent fusetron or circuit breaker.
DRY2022N_SVG
1.
2.
3.
4.
5.
6.
7.
8.
The three-prong earth/ground plug on the power cord should be
plugged directly into a polarized three-slot effective earth/ground
receptacle rated 120 Volts AC (alternating current) 15 Amps. Refer to Figure 26 to determine correct polarity of the wall receptacle.
L1
Earth/Ground
Neutral
Round Earth/Ground Plug
Neutral Side
0 V.A.C.
120 ± 12 V.A.C.
120 ± 12 V.A.C.
Figure 26
Earth/Ground Information
This appliance must be properly connected to protective earth/
ground. In the event of malfunction or breakdown, the earth/
ground will reduce the risk of electric shock by providing a path
of least resistance for electric current.
The dryer is equipped with a cord having an equipment earth/
ground conductor and a three-prong earth/ground plug. The
three-prong earth/ground plug on the power cord should be plugged directly into a polarized three-slot effective earth/ground receptacle rated 110/120 Volts AC (alternating current) 15 Amps.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23
Part No. 804671ENR3
Installation
WARNING
WARNING
This unit is equipped with a three-prong (earth/
ground) plug for your protection against shock hazard and should be plugged directly into a protective
earth/ ground three-prong receptacle. Do not cut or
remove the earth/ground prong from this plug.
To reduce the risk of fire, electric shock, serious injury or death, all wiring and protective earth/ground
connections MUST conform with the latest edition of
the National Electrical Code, ANSI/NFPA No. 70, and
such local regulations as might apply. It is the customer’s responsibility to have the wiring, fuses and
circuit breakers installed by a qualified electrician to
make sure adequate electrical power is available to
the washer.
W823
WARNING
Improper connection of the equipment earth/ground
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if
you are in doubt as to whether the dryer is properly
connected to a protective earth/ground.
W886
Do not modify the plug provided with the dryer – if it will not fit
the outlet, have a proper outlet installed by a qualified electrician.
NOTE: Have a qualified electrician check the polarity of
the wall receptacle. If a voltage reading is measured
other than that illustrated, the qualified electrician
should correct the problem.
Do not operate other appliances on the same circuit.
WARNING
W824
When plugging in the washer:
•
•
•
•
DO NOT overload circuits.
DO NOT use an extension cord.
DO NOT use an adapter.
DO NOT operate both a washer and a gas dryer on the same
circuit. Use separately fused 15 Amp circuits.
The washer is designed to be operated on a separate branch, polarized, three-wire, effective earth/ground, 120 Volt, 60 Hertz,
AC (alternating current), circuit protected by a 15 ampere fuse,
equivalent fusetron or circuit breaker.
The three-prong earth/ground plug on the power cord should be
plugged directly into a polarized three-slot effective earth/ground
receptacle rated 110/120 Volts AC (alternating current) 15 Amps.
Refer to Figure 27 to determine correct polarity of the wall receptacle.
To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to connect
the dryer to the electrical power source.
W037
Washer
Washer requires 120 Volt, 60 Hertz electrical supply and comes
equipped with a 3-prong earth/ground plug. Refer to serial plate
for specific electrical requirements.
NOTE: The wiring diagram is located behind the control panel, inside the control cabinet.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
24
Part No. 804671ENR3
Installation
Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/
Ground Circuit
led and connected to a protective earth/ground in accordance with
all local codes and ordinances.
WARNING
2
3
1
8
Improper connection of the equipment earth/ground
conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if
you are in doubt as to whether the unit is properly
connected to a protective earth/ground.
6
W893
7
•
4
5
•
•
DO NOT modify the plug provided with the unit – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
If the laundry room’s electrical supply does not meet the
above specifications and/or if you are not sure the laundry
room has an effective earth/ground, have a qualified electrician or your local electrical utility company check it and correct any problems.
Do not operate other appliances on the same circuit when this
appliance is operating.
DRY2022N_SVG
1.
2.
3.
4.
5.
6.
7.
8.
WARNING
L1
Earth/Ground
Neutral Side
Round Earth/Ground Prong
Neutral
0 V.A.C.
120 ± 12 V.A.C.
120 ± 12 V.A.C.
This unit is equipped with a three-prong (earth/
ground) plug for your protection against shock hazard and should be plugged directly into a protective
earth/ ground three-prong receptacle. Do not cut or
remove the earth/ground prong from this plug.
W823
Check Installation
Figure 27
WARNING
To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to connect
the washer to the electric power source.
W082
Earth/Ground Instructions
This appliance must be properly connected to protective earth/
ground. In the event of malfunction or breakdown, the earth/
ground will reduce the risk of electric shock by providing a path
of least resistance for electric current.
The appliance is equipped with a cord having an equipment earth/
ground conductor and a three-prong earth/ground plug. The plug
must be plugged into an appropriate outlet that is properly instal-
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
1. Refer to Installer Checklist on the back cover of this manual
and make sure that unit is installed correctly.
2. Run washer with a test load to make sure it is operating properly and properly leveled.
a. Put about six pounds of laundry (four bath towels and
three jeans) into washer.
b. Close door.
c. Select Spin cycle and press Start.
d. When washer spins at high speed, verify that it is stable.
e. If it is not, after cycle is complete, refer to Position and
Level the Washer to readjust leveling legs.
Check Heat Source
Electric Dryers
1. Close the loading door and start the dryer in a heat setting (refer to the operation instructions).
25
Part No. 804671ENR3
Installation
2. After the dryer has operated for three minutes, the exhaust air
or exhaust pipe should be warm.
ing, very blue flame indicates too much air.) Adjust the air
shutter as follows:
a. Loosen the air shutter lockscrew.
b. Turn the air shutter to the left to get a luminous yellowtipped flame, then turn it back slowly to the right to obtain
a steady, soft blue flame.
c. After the air shutter is adjusted for proper flame, tighten
the air shutter lockscrew securely.
5. Reinstall the lower front panel.
Gas Dryers
IMPORTANT: This operation is to be conducted by
qualified personnel only.
1. To view the burner flame, remove the lower front panel of the
dryer.
2. Close the loading door and start the dryer in a heat setting (refer to the operation instructions). The dryer will start, the igniter will glow red and the main burner will ignite.
WARNING
IMPORTANT: If all air is not purged out of gas line,
gas igniter may go off before gas is ignited. If this
happens, after approximately two minutes igniter
will again attempt gas ignition.
To reduce the risk of serious injury or death, lower front panel must be in place during normal operation.
IMPORTANT: If igniter does not light, make sure gas
is turned on.
3. After the dryer has operated for approximately five minutes,
observe burner flame through lower front panel.
4. Adjust the air shutter to obtain a soft, uniform blue flame. (A
lazy, yellow-tipped flame indicates lack of air. A harsh, roar-
W158
6. After the dryer has operated for approximately three minutes,
exhaust air or exhaust pipe should be warm.
1
2
4
3
D702I_SVG
1.
2.
3.
4.
Air Shutter Lockscrew
Air Shutter
Appliance Main Gas Valve
1/8 in. [3.1 mm] Pipe Plug (For checking manifold pressure)
Figure 28
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
26
Part No. 804671ENR3
Installer Checklist
Installer Checklist
Fast Track for Installing the Stacked Washer/Dryer
1
Position Unit Near Installation Area.
7
Connect Dryer Exhaust
System.
CHECK
CHECK
SWD997N_SVG1
2
Remove the Shipping Materials and Install Plugs.
8
Position and Level the
Washer.
CHECK
CHECK
FLW2359N_SVG
3
Connect Fill Hoses.
SWD1029N_SVG1
9
COLD
Wipe Out Inside of
Washer and Dryer
Drums.
HOT
CHECK
CHECK
FLW2304N_SVG
SWD1030N_SVG
4
Connect Drain Hose to
Drain Receptacle.
10
CHECK
Plug In Washer and
Dryer.
CHECK
DRY2669N_SVG
SWD1010N_SVG1
5
GAS ONLY
•
•
11
Recheck Steps.
Connect Gas Supply
Pipe.
Check for Gas Leaks.
D233I_SVG1
CHECK
6
CHECK
ELECTRIC ONLY - Connect Electrical Cord
12
CHECK
Start and Run Dryer in Heat Setting to Verify Dryer is
Heating.
CHECK
D679I_SVG1
Refer to the manual for more detailed information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
27
Part No. 804671ENR3