c7 corvette z06 plate system

c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
This Nitrous Outlet Plate System was designed specifically for the 2015+ Chevrolet Corvette Z06. If you need any assistacnce contact our Tech Help Line at (254)
848-4300.
***Parts List Located in back of Installation Guide***
Tools Needed For Installation:
• Flathead Screwdriver
• 10mm Socket
• 7mm Socket
• Ratchet
• Drill
• 1” Drill Bit
• Ratchet Extension
• 3/8” Quick Disconnect Tool
• 7/16” Wrench
•
•
•
•
•
•
•
•
•
•
•
9/16” Wrench
11/16” Wrench
3/8” Wrench
Floor Jack
4 Jack Stands
T-15 Torx Bit
T-30 Torx Bit
T-40 Torx Bit
Impact Gun (Optional)
Air Compressor
3/4” Socket
Step 1:
Use a flathead screwdriver to loosen the clamp on the
throttle body. After it’s loose, remove the intake tube from
the throttle body.
Step 2:
Remove the four bolts that hold the throttle body with a
10mm socket and ratchet.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 3:
After the 4 throttle body bolts are loose, remove the throttle body.
Step 4:
Place the nitrous plate between the throttle body and
intake manifold.
Step 5:
Put the 10mm bolts that came with your nitrous plate into
the mounting holes on the drivers side of the throttle body
only. Do not tighten them down.
Step 6:
Place the solenoid mounting bracket on front of the
mounting holes on the passenger side of the throttle body.
Put the 2 remaining throttle body mounting bolts into the
holes, then tighten them down with a 10mm socket and
ratchet. Evenly tighten all the throttle body bolts down.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 7:
Place a compression nut and ferrule onto the end of the
hard lines. Then insert the hard lines into the compression
fitting on the solenoid and gently tighten the compression
nut. Do not tighten it all the way. The line with the red nut
is for the fuel solenoid, and the black nut is for the nitrous
solenoid.
Step 8:
Use the jet card that came with your nitrous system to
choose the proper jetting for the amount of horsepower you are wanting to add. Then, insert the jets into the
proper fitting on the plate. Tighten the lines onto the plate
with a 7/16” wrench while using a 3/8” wrench to hold the
jet fitting. After the hard lines are tight on the plate, use a
7/16” wrench to to tighten the compression fittings on the
solneoid.
Step 9:
Locate the jack points on the vehicle, then use a floor jack
to lift the vehicle. Be sure to use jackstands.
Step 10:
Lift the vehicle completely off of the ground.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 11:
Use a 3/4” Socket and Ratchet or Impact gun to remove
both wheels on the passenger side of the vehicle.
Step 12:
On the passenger side rear of the vehicle, remove the five
7mm bolts below the mudflap. Then, remove the ten T-15
Torx bolts and single 10mm bolts.
Step 13:
Use the trim tool to remove the trim fasteners in the passenger side rear fender well.
Step 14:
Gently remove the inner fender well from the vehicle.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 15:
On the front passenger side, use a 7mm socket to remove the four bolts on the bottom rear of the front fender.
Then, remove the two 10mm bolts and remove the splash
guard.
Step 16:
Remove the three 7mm bolts in the front of the fender
well.
Step 17:
Remove the 8 bolts inside the front passenger side fender
well with a T-15 Torx.
Step 18:
Remove the 5 trim tabs inside the fender well. After the
trim tabs are loose, remove the single 10mm bolt.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 19:
Remove the inner fender well by gently pulling down and
outwards on it.
Step 20:
In the engine bay, remove the 2 black plastic covers on
the passenger side fender. There is 1 at the front and
back of the fender.
Step 21:
Lift the cowl on the passenger side of the vehicle and
remove the single 7mm bolt on the fender. Then ,remove
the three T-15 Torx on top of the fnder.
Step 22:
Remove the three bolts that secure the bumper cover with
a T-30 Torx Bit.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 23:
Use the trim tool to remove the 2 trim tabs on the front of
the drivers and passenger side fender wells.
Step 24:
Pop loose the bumper cover on the drivers and passenger side by gently pulling on it.
Step 25:
Use a 7mm socket and extension to remove the bolts that
hold the passenger side headlight.
Step 26:
Remove the passenger side headlight from the vehicle.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 27:
Remove the two 10mm bolts under the headlight location.
Step 28:
Remove the single 10mm bolt at the rear of the fender
near the PCM.
Step 29:
Open the passenger side door of the vehicle, and remove
the single 10mm bolt on the rear of the front fender.
Step 30:
Gently remove the fender from the vehicle.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 31:
After the fender is removed, place it somewhere to avoid
being damaged.
Step 32:
Remove the floor matt from the hatch area.
Step 33:
Use a T-40 Torx to remove the 4 D-Rings in the hatch
area.
Step 34:
Use a trim tool to pop loose the plastic trim in the hatch
area.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 35:
Remove the trim from the hatch area of the vehicle.
Step 36:
Remove the carpet from the floor of the hatch area.
Step 37:
The most user friendly bottle mounting method is our C7
Bottle Mounting Plate (Part Number 00-33019). Not using
the bottle mounting plate will require removal of the exhaust, suspension components, and will require drilling
through the body. For additional bottle mounting info see
the 2nd to last page of this installation guide.
Step 38:
Remove the speaker on the passenger side of the vehicle
with a 7mm socket.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 39:
Reach inside the speaker box and remove the foam insulation.
Step 40:
Drill a 1” hole into the bottom of the speaker box. After the
hole is drilled, put a grommet in the hole.
Step 41:
Drill a 1” hole into the speaker box from inside the read
fender well. After the hole is drilled, place a grommet in
the hole.
Step 42:
Route the nitrous feed hose into the grommet in the
speaker box.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 43:
Route the nitrous feed hose through the grommet in the
bottom of the speaker box and into the rear fender well.
Step 44:
Using a wire fishing pole, route the nitrous hose through
the passenger side rocker panel of the vehicle.
Step 45:
When the nitrous feed hose has reached the front of the
rocker panel, pull it through enough that you can reach
the front of the engine bay.
Step 46:
Route the nitrous feed hose through the frame of the vehicle and into the engine bay.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 47:
Route the nitrous feed hose through the engine bay
and up to the nitrous solenoid. Use an air hose to blow
through the nitrous hose and clear it of any debris. Then
tighten onto the nitrous solenoid inlet fitting with an 11/16”
wrench.
Step 48:
Remove the fuel line retainer clip on the fuel line. The
fuel connection is located on the back drivers side of the
supercharger.
Step 49:
Use a 3/8” Quick Disconnect tool to separate the fuel
line from the injector rail. Placing a towel under the quick
disconnect fitting will help keep the area clean of any fuel
that is in the hose.
Step 50:
Assemble the fuel adapter by putting a drop of Loc-Tite
on the 1/8” NPT x 4AN 45° fitting. Then, tighten the fitting
into the fuel adapter with a 9/16” wrench. Turn the fitting
so that it matches the same orientation as the fuel adapter in the picture.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Step 51:
Push the fuel adapter onto the fuel rail. You may need
to apply some force for it to seat correctly. When the
fuel adapter is properly seated, you will hear a faint click
sound.
Step 52:
Push the fuel hose onto the fuel adapter. When the fuel
hose is properly seated, you will hear a faint click.
Step 53:
Tighten the fuel hose onto the adapter with a 9/16”
wrench.
Step 54:
Route the fuel hose around the back of the supercharger,
and up the passenger side of the supercharger to the fuel
solenoid. Tighten the hose onto the fuel solenoid with a
9/16” wrench.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Step 55:
Use the attached wiring diagram to wire your nitrous system. For a more custom wiring solution, call us and ask
about out our Pro Wiring Harness.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
Wiring Diagram
Now that your system is installed, you can begin wiring it. When wiring your nitrous system,
double check all of your wiring connections. For a clean, professional install we recommend using
heat shrink of all crimped connectors. This will protect the connection, and make the connection
stronger between the wire and crimp-on connector.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
i N S TA L L AT I O N I N S T R U C T I O N S
Bottle Mounting Information
It’s very important to mount your bottle in the proper orientation. Ideally, the bottle should be facing
with the valve to the front of the vehicle. This is because the siphon tube inside the bottle is curved
towards the bottom of the bottle, so it can pick up a steady supply of nitrous. In the event your bottle
cannot be mounted front to back, you can mount it at an angle, or even sideways. If you mount the
bottle sideways, you’ll need to rotate the bottle so that the siphon tube is at a 45° angle. This means
the bottle nipple will be facing towards the back of the vehicle at a 45° angle. This is because upon
acceleration, the nitrous can be pulled away from the siphon tube. With it at an angle it still allows the
siphon tube to be submerged in the nitrous. The siphon tube on Nitrous Outlet bottles are curved in
the same direction as the bottle nipple. If the bottle is mounted front-to-back, the nipple should be facing down towards the floor of the vehicle. If you have any questions about mounting your bottle, call
our Tech Help line at (254) 848-4300.
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
c7 corvette z06 plate system
part number 00-10179-XX
I N S TA L L AT I O N I N S T R U C T I O N S
List of Parts Included:
Hardline Kit (Fuel and Nitrous Lines)
2 x 1/8” NPT x 3/16 90° Compression Fitting
Nitrous Plate
Jet Pack
4 x Throttle Body Mounting Bolts
4 x Throttle Body Mounting Washers
Solenoid Bracket
1/4” NPT x 6AN 45° (Black Fitting)
2 X 1/8” NPT x 4AN 45°
3/8” Modular Fuel Adapter
55” Fuel Feed Hose
192” Nitrous Feed Hose
10lb Bottle Bracket
.122 Nitrous Solenoid
.177 Fuel Solenoid
Universal Solenoid Bracket
Wide Open Throttle Switch
Duckbill Toggle Switch
Relay & Harness
6ft 12g Red Wire
6ft 18g Blue Wire
305 S. 28th street Waco, TX 76710 - TEL 254-848-4300
W W W . N I T R O U S O U T L E T . C O M
important- All appropriate safety equipment (gloves, tools etc.) must be used during the installation of this product(s).
nitro dave’s llc accepts no responsibility for injuries resulting in the installation of any product(s). nitrous oxide is for off-road use only.
Download PDF