Manual for installation,
use and maintenance
MIN600SI
60cm Integrated
Extractor
year
parts + 1 year labour
guarantee
www.matrixappliances.co.uk
Important
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note
that CDA reserve the right to invalidate the guarantee supplied with
this product following incorrect installation or misuse of the appliance
or use in a commercial environment.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault
with your appliance and to register your appliance for guarantee
purposes.
Appliance Model
Serial Number
EU Declarations of Conformity
This appliance has been manufactured to the strictest standards
and complies with all applicable legislation, including Electrical safety
(LVD) 2014/35/EU and Electromagnetic interference (EMC) 2014/30/
2
EU.
(Parts intended to come into contact with food conform to 1935/2004/
EC.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EU DIRECTIVE 2012/19/EU.
At the end of its working life, the product must be taken to a special
local authority waste collection centre or to a dealer providing
appliance recycling services.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health. It also
enables the constituent materials to be recovered, saving both
energy and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a
crossed-out wheeled dustbin.
Please note:
• Under no circumstances should the extractor be connected to any gas ventilation system, flue system or hot air ducting system.
• Do not vent the extractor into an attic or loft space.
• Only house the extractor in rooms with adequate ventilation. Remember that the extractor is powerful and whatever air is extracted needs to be replaced.
• Do not tile the extractor in. It should be removable for service or maintenance.
• Do not use silicone sealant to secure the hood to the wall.
• You must be able to isolate the extractor from the mains electrical supply after installation.
3
• This extractor has been designed to be used in a room with a volume of less than 36 m3.
• Steam cleaners must not be used when cleaning this appliance.
• The performance of your extractor will vary depending on a number
of factors. These include: type of extraction, length of ducting, room
volume, ventilation available and cleanliness of the filters.
4
Using your Extractor
For best performance, you should switch on the extractor 15 minutes
before starting to cook and leave it to run for approximately 15
minutes after the end of cooking.
Control Panel
A – Light switch
B – Power indicator light
C – Power switch
AA
A1 A2
A1
Fig. 1
C
C
B
B
C1 C3
C1
C2 C4
C2
C4
To switch the extractor light on or off
• Slide the light switch to position A1 for off, or A2 for on.
To switch on the extractor, or change the motor speed
• Slide the power switch to the required position. C2 is the lowest speed and C4 is the highest.
To switch the extractor off
• Slide the power switch to position C1 for off.
5
Care and Maintenance
IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF
THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY
SUPPLY.
Cleaning
You should use a nonabrasive cleaner. Any abrasive cleaner
(including Cif) will scratch the surface and could erase the
control panel markings.
You can clean your extractor effectively by simply using a dilute
solution of water and mild detergent and drying to a
shine with a clean cloth, for example the CDA E-Cloth.
Cleaning the (rectangular) grease filter
The grease filter captures grease particles in the air, so is therefore
subject to clogging depending on the frequency of use of the
appliance.
In order to prevent fire hazard it is recommended to clean the
grease filter at a maximum of 2 month intervals by carrying out these
instructions:
Depending on model, you may have either acrylic or aluminium
grease filter(s).
Acrylic grease filter:
1. Remove the cover panel by pushing the fixing clips up and then 6
lifting the panel forwards.
2. Remove the filter retaining wires from the cover panel.
3. R
emove the grease filter and wash by hand in a lukewarm
solution of water and mild detergent. Once clean squeeze
the grease filter but DO NOT wring it out. Clean the filter holder
using a dilute solution of water and mild detergent or with a
damp cloth. Allow the grease filter to dry completely before
reassembling the extractor.
4. Replace the grease filter in the cover panel and reattach the filter retaining wires.
5. R
eplace the cover panel by inserting the lugs on the upper side
in the extractor, and then refasten the fixing clips on the lower
side.
Aluminium grease filters:
1. Remove the filters from the cooker hood and wash in a solution of
warm water and neutral liquid detergent, leaving to soak.
2. Rinse thoroughly with warm water and leave to dry.
3.The filters may alternatively be washed in the dishwasher. The
aluminium panels may alter in colour after several washes in a
dishwasher. This is not a fault and is not cause for replacing the
panels.
Changing the (circular) charcoal filter (re-circulating only):
To ensure best performance of your extractor, you should replace the
charcoal filters every four to six months,
depending on use. ks into position.
3. Replace the cover panel or grease filter that has been removed.
7
Please note the charcoal filter cannot be washed.
To attach a new charcoal filter, follow the steps below:
1. Remove the cover panel (acrylic filter model) or grease filter
(aluminium filter model) as described above.
2. P
lace the charcoal filter on the centre of the motor support, and
once firmly located turn the charcoal filter clockwise 90º until the
charcoal filter locks into position.
3. Replace the cover panel or grease filter that has been removed.
Changing the Light
DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE
BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT.
Remove the cover panel as described above, unscrew the light bulb
and replace the light with the correct type of light bulb (28W max candle bulb SES (small screw type). Finally, replace the cover panel.
Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights.
The light is designed for use during cooking and not for general room
illumination. Extended use of the light can reduce the life span of the
bulb.
Bulb replacement is not covered by the guarantee.
8
Only use bulbs recommended for your extractor. Do not fit bulbs of a
higher power rating. Bulbs of a lower power rating may be adequate
for use, generally last longer and use less energy.
Spare bulbs are available from CDA Customer Care or from your local
DIY shop.
9
Installation requirements
When the extractor is to be installed above an electric hob, the
minimum distance between the hob and extractor must exceed
600mm (650mm is recommended).
When the extractor is to be installed above a gas hob, the minimum
distance between the hob and extractor must exceed 700mm (750mm
is recommended).
If the instructions provided with your gas hob state that the required
distance between the hob and extractor must be greater than 700mm,
then that is the distance that should be observed; this is a legal
requirement and may lead to your hob being disconnected from the
gas supply and the installation being reported to RIDDOR (The height
should be measured from the top of the burners).
NOTE: IN THE ABSENCE OF ANY
INSTRUCTIONS SUPPLIED WITH
THE GAS HOB, THE MINIMUM
DISTANCE BETWEEN THE HOB
Gas: 750mm recommended
Electric: 650mm recommended
AND EXTRACTOR MUST BE AT
LEAST 760mm.
Hob
The width of any hob must not
be greater than the width of the
extractor installed above it.
10
Fig. 2
Installation procedure
1. Mark the positions of the fixing holes on the wall using the dimensions shown in Fig. 3.
2.Drill and plug the wall with appropriate fixings, suitable for the wall type you are fixing the extractor on.
3.Mount the brackets and securely tighten.
4.Hang the hood on the brackets and adjust the brackets and
height to suit. The adjustment mechanism is shown in Fig. 4.
5.Once the hood is levelled and square against the wall, adjust the bottom panel as required (Fig. 5).
6.Secure the extractor to the adjacent units through the holes in the side of the product, to ensure that it cannot be accidentally knocked off the hanging brackets.
55
Adjacent Cabinet
55
553
Fig. 3
23.5
11
Fig4
Fig. 5
Mains Electricity Connection
THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY
A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE
SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE.
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.T. and local regulations.
The wires in the mains lead of this appliance are coloured in
accordance with the following code:
BLUE = NEUTRAL, BROWN = LIVE.
12
As the colours of the wires in the mains lead for the appliance may
not correspond with the coloured markings identifying the terminals
connecting to the fused spur, proceed as follows:
• The wire which is coloured blue must be connected to the terminal
marked N (Neutral), or coloured black.
• The wire which is coloured brown must be connected to the
terminal marked L (Live), or coloured red.
NOTE: USE A 3A FUSE
Assembly and electrical connection should be carried out by
competent personnel.
When installing this product we recommend you seek the help of
another individual.
IMPORTANT: THIS APPLIANCE IS A CLASS II APPLIANCE (DOUBLE
INSULATED) AND IS NOT INTENDED TO BE EARTHED. DO NOT FIT AN
EARTH LEAD TO THIS EXTRACTOR.
Do not mount the isolation switch behind the chimney section. It is a
requirement that you must be able to isolate the
extractor from the mains electrical supply after installation.
This appliance is intended to be connected to the mains electrical
supply by means of an isolation switch and fused spur and is
intended to be protected by a 3A fuse. The use of a 13A fuse can
cause damage to the internal wiring in the event of a fault, and may
also invalidate the warranty.
13
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
USE A 3 AMP FUSE
Electrical Information
Mains electrical voltage: 230 – 240Vac.
Total rated power consumption: 148W.
Troubleshooting
If your extractor is not working:
1. Check that the mains supply has not been switched off.
2. Check that the fuse in the spur has not blown.
Contact CDA Customer Care
A : Customer Care Department, The CDA Group Ltd, Harby Road,
Langar, Nottinghamshire, NG13 9HY
T : 01949 862 012 F : 01949 862 003
E : customer.care@cda.eu W : www.cda.eu
14
Energy Efficiency Information
Attribute
Model Identification
Annual Energy Consumption
Symbol
AECHood
MiIN600S I
80.8
Value
Units
Time increase factor
Fluid Dynamic Efficiency
f
FDEHood
1.8
6.1
Energy Efficiency Index
EEIHood
98.8
Measured airflow at Best Efficiency
Point
Measured Pressure at Best Efficiency
Point
Maximum airflow
QBEP
115.2
m3/h
PBEP
178.0
Pa
QMAX
197.0
Measured electric power at Best
Efficiency Point
Nominal lighting power
Average illumination of the lighting
system on the cooking surface
WBEP
93.0
m3/h
W
WL
EMiddle
28.0
47.0
W
Lux
Measured power consumption in
standby
Measured power consumption off
mode
Sound power level
PS
NA
W
PO
0.0
W
LWA
62.0
dBA
Grease Filter Efficiency
GFEHood
64.3 (E )
%
Lamp efficiency
LEHood
2 (G)
%
kWh
15
Serviced by
For our Customer Care Department, or for Service,
please contact us on:
The CDA Group Ltd. Harby Road, Langar, Nottinghamshire, NG13 9HY
Tel: 01949 862012 Fax: 01949 862003 Email: customer.care@cda.eu
Download PDF