installation instructions

Option 1:
Burlington has 4 different style handle for your selection.
INSTALLATION INSTRUCTIONS
Bridge Basin Mixer, with plug & chain
(Excluding handles & bases)
-
T16
Claremont
Anglesey
Birkenhead Kensington
Option 2:
27mm
Burlington also have a base (27mm height) for your selection.
NOT INCLUDED IN THE TAP BOX
Important
● We recommend that this product is installed by a qualified professional contractor. Such as a plumber who is certified by NVQ
(National Vocational Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3
● Please check this product immediately to ensure that it has not been damaged and is complete. Before installation, please make
sure this product is the correct model and you have all the parts required for installation and using.
● All the taps in Burlington Range should be supplied with hot and cold water at balanced pressure. If not, then the mixing function
will not work correctly. It is necessary to fit non-return valves on both hot and cold feeds pipe. These are not supplied.
● Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the taps.
● Turn off water supply before commencing work, this should be done at the isolating valves of inlet feeds if fitted or main stopcock.
● Please read these instructions carefully and keep it for future reference.
Working pressure
The tap is suitable for both high and low pressure installation. To ensure that the tap works well under low water pressure, the
cold water storage tank must be at least 2 meters above the installed position. The maximum static pressure is 10 bar, and
operating water pressure is 5 bar. Where the operating water pressure above 5 bar, then a pressure reducing valve must be fitted.
Decoration heads (alternative option)
The tap comes with a factory-fitted decoration head at the center of tap, and also
has an alternative decoration head for your option.
If it is needed to replace, please screw off the factory-fitted decoration head,
and screw on the spare one.
Straightener and aerator (alternative option)
The tap comes with a factory-fitted flow straightener for use with water pressure
between 0.2 ~ 0.45 bar. If the water pressure is over 0.45 bar, replace the
factory-fitted flow straightener with the high pressure aerator supplied.
THE CORRECT STRAIGHTENER /AERATOR MUST BE INSTALLED TO AVOID
WATER SPRAYING IN AN UNCONTROLLED FASHION WHEN SWIVELING THE SPOUT.
Use NEOPERL Key to unscrew the straightener in the Nozzle. Replace with
the aerator provided, and screw back in nozzle tightly. (If you misplace the
Neoperl key you can use the top of the aerator/straightener as a key)
FLOW STRAIGHTENER
AERATOR
Cleaning
Before use: Unscrew the filter and allow the water to run freely for
5 minutes. Then screw the filter back in place.
Periodically: Using the key provided unscrew the nozzle and remove.
Rinse it with cleaning running water until any loose debris is cleared.
Then replace the nozzle and tighten with key provided.
1-2
NOZZLE
KEY
C
Dimension
244
65
80
21.6
219
139
65
100
G1/2
100
200
Installation
126
COLD
INDICE
Ø48
DECORATIVE
CAP
HOT
INDICE
SCREW
SPRING WASHER
FLAT WASHER
HANDLE
COLD TAP
BODY
HOT TAP BODY
NOT INCLUDED IN THE TAP BOX
Note: To ensure the Kensington lever tap head
faces in the correct forward position once
installed, you may need to tighten the
cartridge into the tap body a notch with
a monkey spanner and then re-attach the
tap head.
360° SWIVEL
“O” RING
CHAIN
RUBBER
WASHER
Basin
Worksurface
STUD
FIXING NUT
NUT
CONE
WASHER
1. Fit the “O” ring into the groove on the underside of the tap left and right body.
2. Insert the tap body into the two tap holes on basin from above.
WASTE
BODY
Basin
Waste Hole
3. Tighten the rubber washer & the fixing nut and fix the body on the basin.
4. Install Plug & Chain waste:
a) Remove the nut from the screw at the end of chain.
b) Insert the screw into the basin waste chain hole, just near the 3 overflow holes.
c) Put the nut back to screw and tighten it on the backside of basin.
d) Insert the plug waste in the basin waste hole and tighten.
e) Shear the chain if it’s too long in your basin.
Caution
SEAL
NUT
BASIN
CAP
The swivel spout should not be used as a subsitute for on/off function.
Use handles in all circumstances to close water flow.
If the chain hole is not used please
cover it with the cap supplied.
Maintenance
We do NOT recommend you use any household cleaners to clean the product. Because these cleaners change substance or formula
too frequently. The product should be always cleaned only with soapy water and rinsed with clean water and dried with a soft cloth.
2-2
C
Download PDF