FASTCAT RZ 627cc VANGUARD B&S W/42 SIDE DISCHARGE
942315H
FASTCAT RZ FR651V KAW W/52 SIDE DISCHARGE
942316H
FASTCAT RZ FR691V KAW W/61 SIDE DISCHARGE
Rev. A 05-2012
MAN 4167661
PARTS / OPERATOR’S MANUAL
942311H
CALIFORNIA
WARNING
Proposition 65 Warning
Diesel engine exhaust and some of its
constituents are known to the State of
California to cause cancer, birth defects
and other reproductive harm.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Californie Proposition 65 Avertissement
Les échappements des moteurs diesel et
certains de leurs composés sont reconnus par
l’Etat de Californie pour être cancérigènes,
provoquer des défauts congénitaux et d’autres
dangers en matière de reproduction.
California Advertencia
de la Proposicion 65
El estado de California hace saber que
los gases de escape de los motores diesel
y algunos de sus componentes producen
cáncer, defectos de nacimiento y otros
daños en el proceso de reproducción
humana.
AVERTISSEMENT
L’émission du moteur de ce matériel contient des produits chimiques que l’Etat de
Californie considère être cancérigènes,
provoquer des défauts congénitaux et
d’autres dangers en matière de reproduction.
ADVERTENCIA
El estado de California hace saber que los
gases de escape de este producto contienen
productos quÍmicos que producen cáncer,
defectos de nacimiento y otros daños en
el proceso de reproducción humana.
CALIFORNIA
Proposition 65 Warning
Battery posts, terminals, wiring
insulation, and related accessories
contain lead and lead compounds,
chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
WASH HANDS AFTER HANDLING.
FastCat RZ
IMPORTANT MESSAGE
Thank you for purchasing this Schiller Grounds Care, Inc. product. You have purchased a world class mowing product, one
of the best designed and built anywhere.
This machine comes with an Operation and Safety Manual. The useful life and good service you receive from this machine
depends to a large extent on how well you read and understand this manual. Treat your machine properly, lubricate and
adjust it as instructed, and it will give you many years of reliable service.
Your safe use of this Schiller Grounds Care, Inc. product is one of our prime design objectives. Many safety features are
built in, but we also rely on your good sense and care to achieve accident-free operation. For best protection, study the
manual thoroughly. Learn the proper operation of all controls. Observe all safety precautions. Follow all instructions and
warnings. Do not remove or defeat any safety features. Make sure those who operate this machine are as well informed
and careful in its use as you are.
See a Schiller Grounds Care, Inc. dealer for any service or parts needed. Schiller Grounds Care, Inc. service ensures that you
continue to receive the best results possible from Schiller Grounds Care, Inc. products. You can trust Schiller Grounds Care,
Inc. replacement parts because they are manufactured with the same high precision and quality as the original parts.
Schiller Grounds Care, Inc. designs and builds its equipment to serve many years in a safe and productive manner. For
longest life, use this machine only as directed in the manuals, keep it in good repair and follow safety warnings and instructions. You'll always be glad you did.
Schiller Grounds Care, Inc.
One Bob Cat Lane
Johnson Creek, WI 53038-0469
TABLE OF CONTENTS
PAGE
SAFETY..........................................................................................................................................................2-8
SET UP INSTRUCTIONS............................................................................................................................ 9, 10
LABELS...................................................................................................................................................... 11-14
CONTROLS................................................................................................................................................15-18
PRE-OPERATION CHECK LIST..................................................................................................................... 19
OPERATION...............................................................................................................................................20-22
MAINTENANCE CHART................................................................................................................................. 23
MAINTENANCE RECORD ............................................................................................................................. 24
MAINTENANCE.........................................................................................................................................25-31
ADJUSTMENTS ........................................................................................................................................32-34
BELT REPLACEMENT.............................................................................................................................. 35, 36
PARTS SECTION............................................................................................................................................ 37
FRAME-ENGINE/CLUTCH ASSY........................ FIGURE 1.................................................................... 38, 39
TRANSAXLE ASSY.............................................. FIGURE 2.................................................................... 40, 41
FUEL TANK/BUMPER & CONTROL PANEL....... FIGURE 3.................................................................... 42, 43
FUEL VALVE & COVER PLATE........................... FIGURE 4.................................................................... 44, 45
DECK LIFT ASSEMBLY....................................... FIGURE 5.................................................................... 46, 47
CASTER ASSEMBLY........................................... FIGURE 6.................................................................... 48, 49
KICKPLATE/SEAT ASSEMBLY............................ FIGURE 7.................................................................... 50, 51
STEERING........................................................... FIGURE 8.................................................................... 52, 53
PARKING BRAKE................................................ FIGURE 9.................................................................... 54, 55
WIRE HARNESS.................................................. FIGURE 10.................................................................. 56, 57
42" SIDE DISCHARGE........................................ FIGURE 11.................................................................. 58, 59
52" SIDE DISCHARGE........................................ FIGURE 12.................................................................. 60, 61
61" SIDE DISCHARGE........................................ FIGURE 13.................................................................. 62, 63
BELTS-CUTTERDECK......................................... FIGURE 14.................................................................. 64, 65
DECALS-POWERUNIT........................................ FIGURE 15.................................................................. 66, 67
ACCESSORIES-SUSPENSION SEAT................. FIGURE 16.................................................................. 68, 69
05-2012
1
SAFETY
FastCat RZ
NOTICE !!!
Unauthorized modifications may present extreme
safety hazards to operators and bystanders and
could also result in product damage.
Schiller Grounds Care, Inc. strongly warns against,
rejects and disclaims any modifications, add-on
accessories or product alterations that are not
designed, developed, tested and approved by Schiller
Grounds Care, Inc. Engineering Department. Any
Schiller Grounds Care, Inc. product that is altered,
modified or changed in any manner not specifically
authorized after original manufacture–including the
addition of “aftermarket” accessories or component
parts not specifically approved by Schiller Grounds
Care, Inc. will result in the Schiller Grounds Care,
Inc. Warranty being voided.
Any and all liability for personal injury and/or property
damage caused by any unauthorized modifications,
add-on accessories or products not approved by
Schiller Grounds Care, Inc. will be considered
the responsibility of the individual(s) or company
designing and/or making such changes. Schiller
Grounds Care, Inc. will vigorously pursue full
indemnification and costs from any party responsible
for such unauthorized post-manufacture modifications
and/or accessories should personal injury and/or
property damage result.
This symbol means:
ATTENTION!
BECOME ALERT!
Your safety and the safety of others is involved.
Signal word definitions:
The signal words below are used to identify levels
of hazard seriousness. These words appear in this
manual and on the safety labels attached to Schiller
Grounds Care, Inc.machines. For your safety and
the safety of others, read and follow the information
given with these signal words and/or the symbol
shown above.
DANGER indicates an imminently hazardous
situation which, if not avoided, WILL result in death
or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
CAUTION indicates a potentially hazardous situation
which, if not avoided, MAY result in minor or moderate
injury. It may also be used to alert against unsafe
practices or property damage.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, MAY result in property damage
MODEL NUMBER: This number appears on
sales literature, technical manuals and price lists.
SERIAL NUMBER: This number appears only
on your mower. It contains the model number
followed consecutively by the serial number.
Use this number when ordering parts or seeking
warranty information.
* Serial Plate located on left side panel near cut-off switch.
2
SAFETY
FastCat RZ
PREPARING FOR SAFE OPERATION
WARNING
Operator preparation and training
Read the Operation & Safety
Manual
- If an operator or mechanic
cannot read English, it is
the owner's responsibility
to explain this material to
them. If any portion of this
material is unclear, contact
your factory representative for clarification.
All rotary lawnmowers are potentially
dangerous. They can amputate hands and
feet and throw objects. Failure to follow
these safety and operating instructions
could result in serious injury or death.
- Become familiar with the safe operation of the
equipment, operator controls and safety signs.
Know how to stop the engine and attachments
quickly in an emergency. Do not operate or allow
another person to operate this machine if there
are any questions about safety.
-
All operators and mechanics should be trained.
The owner is responsible for training the users.
-
Wear appropriate clothing, including long
trousers and safety goggles or safety glasses
with side shields when operating mower. Do not
operate barefoot or wearing open sandals. Long
hair, loose clothing or jewelry may get tangled in
moving parts.
Site preparation and circumstances
-
Evaluate the terrain to determine what
accessories and attachments are needed to
properly and safely perform the job. Only use
accessories and attachments approved by the
manufacturer.
-
Clear the area to be mowed of objects such as
rocks, toys, wire or other debris that may be
picked up or thrown by the mower.
-
Wear hearing protection.
-
Never allow underage children, unskilled
or improperly trained people operate this
equipment. Local regulations can restrict the age
of the operator.
-
Be sure the area is clear of pets and people,
especially young children. Never assume they
will remain where you last saw them. Stop the
machine if any enter the area.
-
Data indicates that those operators age 60 years
and above are involved in a large percentage of
riding mower-related injuries. Those operators
should evaluate their ability to operate the riding
mower safely enough to protect themselves and
others from injury.
-
Mow only in daylight or in good artificial light.
-
Do not mow wet grass as tires may lose traction.
-
Do not carry passengers, especially small
children. They may fall off and be seriously
injured.
- Keep warning labels and this operator's manual
legible and intact. Replacement labels and
manuals are available from the factory.
- Do not operate machine while under the
influence of drugs or alcohol.
-
The owner/user can prevent and is responsible
for accidents or injuries occurring to themselves,
other people or property.
3
SAFETY
FastCat RZ
Machine preparation
OPERATING SAFELY
-
Check operator presence interlock system and
brake operation. Adjust or repair any problems
before using.
In general
-
Use extra care when loading or unloading the
machine into a trailer or truck.
-
Do not tamper with or defeat safety devices.
Keep guards, shields and interlock safety devices
in place and in proper working condition. They
are for your protection.
-
Slow down and use caution when making turns
and crossing roads and sidewalks. Stop blades if
not mowing.
-
-
Keep all fasteners such as nuts, bolts and pins
well secured.
Do not run the engine in an enclosed area where
dangerous carbon monoxide fumes can collect.
-
-
Visually inspect blades, blade bolts and the cutter
assembly for wear or damage. Replace worn or
damaged blades and bolts to preserve balance.
Do not place your foot on the ground while
operating the machine.
-
Before operating, lower the discharge chute,
install the mulcher or put the entire grass catcher
in place.
-
Keep clear of the discharge opening at all times.
Never direct the discharge toward a bystander.
Stop operation if someone approaches.
-
Keep washout ports and other mower housing
service openings closed when mowing.
-
Use care when pulling loads or using heavy
equipment.
- Use only approved drawbar hitch points.
- Limit loads to those you can safely control.
- Do not turn sharply. Use care when reversing.
- Use counterweight(s) or wheel weights when
suggested in the operator's manual.
-
Verify that machine and attachments, if any, are
in good operating condition.
-
Do not engage blades until ready to mow.
-
4
Never leave a machine unattended. Always turn
off blades, set parking brake, stop engine and
remove key before dismounting.
SAFETY
FastCat RZ
Starting
Interrupting operation
-
Start only according to instructions in this manual
or on the machine.
-
Before attempting to start the engine, make sure:
- the parking brake is on;
- the PTO is disengaged;
- the traction drive is in NEUTRAL.
-
Before leaving the operator's position:
- Park on level ground.
- Disengage the PTO.
- Set the parking brake.
- Shut off the engine and remove the key.
-
-
When starting the engine, make sure hands and
feet are clear of the blades.
Disengage the PTO and wait until the blades quit
rotating:
- before raising cutterdeck;
- when not mowing;
- for transport;
- when crossing surfaces other than grass.
-
Do not start the machine while standing in front
of the discharge chute or with the chute directed
at someone.
-
Do not engage PTO at full throttle. Throttle to
idle or lowest possible engine speed.
-
Do not change engine governor settings or
overspeed the engine. Operating the engine
at excessive speed can increase the hazard of
personal injury.
-
-
Stop the engine, disengage the PTO, set parking
brake and wait until the blades quit rotating and
lower cutting unit:
- before refueling;
- before removing grass catcher;
- before making height adjustment unless the
adjustment can be made from the operator's
position.
Stop the engine, disengage the PTO, set parking
brake and disconnect the spark plug wire(s) or
remove the key:
- before clearing blockages or unclogging chute;
- before checking, cleaning or working on the
machine;
- after striking a foreign object. Inspect the
machine for damage and make repairs before
restarting;
- if the machine begins to vibrate abnormally:
shut off machine immediately. Inspect and
make repairs as needed before restarting;
- except for repairs or adjustments as specifically
noted, such as for carburetor adjustment,
where the engine must be running. Keep
hands and feet clear of moving parts in these
circumstances.
-
Allow the blades to come to a complete stop
when stopping operation to clear blockages,
unclog, inspect the machine, do maintenance or
repair.
-
Reduce the throttle setting during engine shutdown and, if the engine is provided with a shutoff valve, turn the fuel off at the conclusion of
mowing.
5
SAFETY
FastCat RZ
MANEUVERING SAFELY
In general
-
Slow down before turning.
-
Do not mow in reverse unless absolutely
necessary. Always look behind and down
for small children and pets before and during
backing.
-
Use extra care with grass catchers or other
attachments. These can change the stability of
the machine.
-
Remove obstacles such as rocks, tree limbs etc.
-
Avoid driving over obstacles such as ruts, holes,
rocks and roots whenever possible. Be alert to
dips and rises. Uneven terrain can overturn a
mower or cause it to slide. Tall grasses can hide
obstacles.
-
Be aware when approaching blind corners,
shrubs, trees, tall grass or other objects that may
obscure vision.
-
If tires lose traction, disengage the blades. If on
a slope, head downhill.
-
Do not mow dropoffs, ditches or embankments.
The machine could suddenly turn over if a wheel
runs over the edge or an edge caves in.
WARNING
-
Follow the manufacturer's recommendations
for wheel weights or counterweights to improve
stability.
-
Do not mow slopes when grass is wet. Reduced
traction could cause sliding.
Mowing slopes
Slopes are a major factor in
loss-of-control and tip over
accidents that sometimes lead
to severe injury or death. All
slopes require extra caution.
-
Do not mow on slopes if uneasy or uncertain.
Ultimate responsibility for safe operation on
slopes rests with the operator.
-
Do not mow excessively steep slopes.
-
On zero turn machines, mow across slopes, not
up and down.
-
Avoid starting or stopping on a slope. If tires
lose traction, disengage the blades and proceed
slowly straight down the slope.
-
With a zero turn machine, if tires lose traction
going down a slope, steering control may be
regained by speeding up.
-
Mid-mount zero turns (belly mounted deck) have
much greater traction pointed up slope than
down slope. Be aware that traction may be lost
going down a slope. Do not operate a mid-mount
zero turn on slopes it cannot back up.
-
Keep all movement on the slopes slow and
gradual. Do not make sudden changes in speed
or direction.
-
Do not turn on slopes unless necessary, and then
turn slowly and downhill when possible.
-
Stay away from slopes if the ground is loose or if
caught in the rain during mowing.
-
Use lower speeds on a slope to avoid stopping or
shifting.
6
SAFETY
FastCat RZ
MAINTENANCE SAFETY
Blades
In general
-
Mower blades are sharp and
can cut. Use extra caution
when handling. Remove obstructions with care. Wrap the
blade(s) or wear gloves.
-
Be aware that rotating one
blade on multiblade mowers
can cause other blades to
rotate.
WARNING
-
Maintain machine according to manufacturer's
schedule and instructions for maximum safety
and best mowing results.
-
Park machine on level ground.
-
Never allow untrained personnel to service machine.
-
Adjust or repair only after the engine has been
stopped and the blades have quit rotating.
-
-
Inspect grass catcher components regularly. If
worn, damaged or deteriorated, they may expose
moving parts or allow objects to be thrown.
Only replace blades. Never straighten or weld
them.
-
Keep other persons away from blades.
Replace parts if worn, damaged or faulty.
For best results, always replace with parts
recommended by the manufacturer.
Fuel
-
-
-
Disconnect battery or remove spark plug wire(s)
before making any repairs. Disconnect the
negative terminal first and the positive last. Reconnect positive first and negative last.
Do not dismantle the machine without releasing
or restraining forces which may cause parts to
move suddenly.
-
Provide adequate support, e.g. jackstands for
lifted machine or parts if working beneath.
-
Do not put hands or feet near or under rotating
parts.
-
Clean up spilled oil or fuel thoroughly.
-
Replace faulty mufflers.
- To reduce fire hazards, keep the engine, muffler,
battery compartment and fuel storage area free
of grass, leaves, debris buildup or grease.
- Hydraulic fluid can penetrate skin, use paper
to check for leaks. Relieve hydraulic pressure
before disconnecting hoses. Make sure
connections are tight and hoses are in good
condition.
WARNING
-
Gasoline and diesel fuels are
flammable; gasoline vapors
are explosive. Use extra care
when handling.
-
Store only in containers specifically designed for fuel.
-
When refueling or checking fuel level:
- Stop the engine and allow to cool;
- Do not smoke;
- Refuel outdoors only;
- Use a funnel;
- Do not overfill;
- If fuel is spilled, do not attempt to start the
engine until the spill is cleaned up and vapors
have cleared.
Sparks from static electricity can start fires or cause
explosions. Flowing fuel can generate static
electricity. To prevent static electricity sparks:
- Keep containers electrically grounded. Do not fill
containers in a vehicle or on a truck or trailer bed
with a plastic liner. Fill containers on the ground
away from the vehicle.
-
When practical, remove gas powered equipment from the truck or trailer and refuel it on the
ground. If equipment must be refueled on the
truck or trailer, refuel from a portable container
rather than a dispenser nozzle.
-
Keep the dispenser nozzle in contact with the rim
of the fuel tank or container opening until fueling
is complete. Do not use a nozzle lock-open
device.
-
Replace caps on fuel cans and tanks securely.
7
SAFETY
FastCat RZ
BATTERY
WARNING
JUMP STARTING
Battery acid is caustic and fumes
are explosive and can cause
serious injury or death.
1. Be sure the jumper cables are in good condition.
Turn off the ignition and all electrical accessories
on both machines.
To reduce the risk of personal
injury when working near a battery:
2. Position the machine with a good (charged) battery next to but not touching the machine with the
dead battery so jumper cables will reach.
- When working with battery
acid, use protective equipment
such as, but not limited to, goggles, face shield,
rubber gloves and apron.
3. When making cable connections:
-
Avoid leaning over a battery.
-
Do not expose a battery to open flames or
sparks.
-
Be sure batteries with filler caps are properly
filled with fluid.
-
Do not allow battery acid to contact eyes or skin.
Flush any contacted area with water immediately
and get medical help.
-
Charge batteries in an open, well ventilated area,
away from sparks and flames. Unplug charger
before connecting or disconnecting from battery. - make sure the clamps do not touch anywhere
except to intended metal parts,
- Never connect a positive ("+" or red) terminal
to a negative ("–" or black) terminal.
- Make sure the cables won't get caught in any
parts after the engines are started.
4. Connect one end of the first jumper cable to the
positive terminal on one battery. Connect the
other end to the positive terminal on the other
battery.
5. Connect one end of the other cable to the
negative terminal of the machine with a good
(charged) battery. Make the final connection on
the engine of the machine to be started, away
from the battery.
6. Start the vehicle with the good battery, then the
machine with the discharged battery.
TRANSPORTATION AND STORAGE SAFETY
-
Stop the engine and allow to cool before storing.
-
Drain the fuel tank outdoors only.
- Store fuel in an approved container in a cool, dry
place.
-
Keep the machine and fuel containers in a locked
storage place to prevent tampering and to keep
children from playing with them.
-
When the machine is to be parked, stored or left
unattended, lower the cutterdeck unless a positive mechanical lock is used.
-
Do not store the machine or fuel container near
heating appliances with an open flame such as a
water heater or an appliance with a pilot light.
-
Keep gasoline storage area free of grass, leaves
and excessive grease to reduce fire hazard.
-
Clean grass and debris from cutting units, drives,
mufflers and engine to help prevent fires.
8
7. Remove the cables in the exact reverse order of
installation. When removing each clamp, take
care it does not touch any other metal parts while
the other end remains attached.
SET UP INSTRUCTIONS
FastCat RZ
TOOLS REQUIRED FOR ASSEMBLY
-
-
-
-
-
Wrecking bar
Claw hammer
Sockets: 1/2”, 15/16
Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16”
Tire pressure gauge
NOTE: All references below to the “right” or “left” are with respect to an operator at the controls.
1. UNCRATE UNIT
a) Discard packing materials. Loosen the caster wheel axle bolts and bumper bolts to remove the shipping
brackets.
Discard shipping brackets.
b) Re-install and tighten bumper bolts.
c) Tighten caster wheel axle bolts against caster axle spanner bushings to 80 ft/lbs.
2. TIRE PRESSURE
a) Set tire pressures to 15 lbs/in2 (0.8 kg/cm2). Tires are overinflated for shipping.
3. TRACTION LEVERS
a) Tighten bolt A.
b) Sit on the machine. Levers C may be moved to
upper set of holes in bar B for a better operator
fit.
9
SETUP INSTRUCTIONS
FastCat RZ
4. FINAL PREPARATIONS
-
Check the engine and hydraulic oil levels. Top off with the correct oil if necessary. Use 10W30 motor
oil for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system. After 1 hour of operation
check hydraulic oil levels when machine is cold.
-
Insure Battery cables are connected properly.
Battery acid is caustic. Fumes are explosive and can cause serious injury or death.
Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries.
Read and obey the battery manufacturer’s instructions.
Be certain the ignition switch is OFF and the key has been removed before servicing the battery.
a) Verify battery polarity before connecting or disconnecting the battery cables.
b) When installing the battery, always assemble the RED, positive ( + ) battery cable first and the
ground, BLACK, negative ( - ) cable last.
c) Tighten cables securely to battery terminals and apply a light coat of silicone dielectric grease to terminals and cable ends to prevent corrosion. Keep terminal covers in place.
-
Insure all battery cables are routed correctly, to avoid any rotating or moving component to prevent any
cable damage.
-
Read Operation and Safety Manual before starting. Operator Manual is located under the footplate. Tilt
foot plate forward to access manual.
OPERATOR'S MANUAL IS LOCATED
UNDER THE FOOT PLATE.
4167202
-
Deck can be adjusted to allow for best horsepoer, best quality or best striping. See deck leveling procedure in the Adjustments Sectioin in this manual to set as desired.
-
Run engine at full RPM for 5 minutes before engaging blades to allow the engine to be fully lubricated
before load is applied.
-
Check the hydrostat neutral adjustment. Neutral is set at the factory but may require readjustment. See
adjustments section in the this manual.
-
Do not use the machine without an approved grass collector, the grass discharge chute or mulching
plates correctly fitted.
10
LABELS
FastCat
bORDER IS NOTRZ
BLUE,
BORDER IS WHITE.
F
N
N
PTO SWITCH
4165616
R
F
N
N
4165662
R
4165615
11
LABELS
4
1
42
FastCat RZ
441
2
343
31
3
341
234
221
241
441
4
1
32
2
134
121
4167104
421
343
3
341
1
22
234
2
241
1
12
134
4167103
12
LABELS
FastCat RZ
BEFORE STARTING OR SERVICING:
Read and understand the
Operator's Manual & labels.
- Be sure machine is in safe operating condition.
- Move traction levers to neutral lock, parking brake to ON.
- Set PTO switch to OFF.
NOTE: Decal is located
under foot plate.
BEFORE LEAVING SEAT:
- Move traction levers to neutral lock, parking brake to ON.
- Set PTO switch to OFF.
- Turn engine keyswitch to OFF.
- Remove key.
AVOID SERIOUS INJURY OR DEATH:
- Read and obey the Operation & Safety Manual.
- Remove objects that could be thrown by the blades.
- Use caution on slopes. Stay off slopes the machine
cannot back up.
- Stop blades and drive down slowly if machine slides
or stops going on slope.
- Do not mow when children or others are around.
- Do not carry a child or passenger-even with blades off.
- Look down and behind before and while backing.
- Do not operate unless trained.
- Do not operate unless guards, shields and interlocks
are in place and working.
- Replace labels and Operation and Safety Manual if lost
or damaged.
2 SPINDLE
CONFIGURATION
3 SPINDLE
CONFIGURATION
12
- Remove debris buildup. Debris under belt cover or
near muffler can cause fires.
- Blades continue to rotate for a few seconds after
blades are turned off.
- Blades must be at least 1/8" above bottom of housing.
- All blades must be identical. Check blade bolts daily
for tightness.
- Inspect for damage after striking a foreign object.
Make repairs before restarting operation.
- Find and repair cause of any abnormal vibration.
1/
1
1
2
1
2
2
2
1/
2
4164525
- Leer el manual del operador. No permitir que
personas no capacitadas para ello usen la máquina.
- Mantener los protectores en su lugar y sus tornillos
debidamente fijados.
- Antes de limpiar, ajustar o reparar este equipo,
apagar todos los mandos, aplicar el freno de
estacionamiento y apagar el motor.
- Mantener las manos, los pies y la ropa alejados de
las piezas en movimiento.
- No conducir como pasajero ni llavar pasajeros en
máquinas sin asiento para ello.
- Mantener a las demás personas alejadas durante
el funcionamiento de la máquina.
- Si no sabe leer inglés, solicitarie a otra persona
que le lea y explique el contenido de las etiquetas y
del manual de la máquina.
4165610
13
LABELS
FastCat RZ
OPERATOR'S MANUAL IS LOCATED
UNDER THE FOOT PLATE.
4167202
P
OFF
O
P
I
ON
PARKING
BRAKE
4167203
14
CONTROLS
FastCat RZ
KEYSWITCH (K) - The keyswitch has three
positions: OFF, RUN, and START. Insert the key
and turn it clockwise to move the switch from OFF to
RUN. Turn it further to START and hold to engage
the starter. Release the key and the switch will return
to RUN from START. Turn the key counterclockwise
to OFF to stop the engine.
THROTTLE (T) - Move the throttle lever forward to
increase engine speed until the maximum governed
engine RPM is reached. Move the lever rearward to
decrease engine speed until the engine reaches its
idle speed.
CHOKE (C)
Pull the choke control out to set the choke ON. Push
it in to set the choke OFF.
POWER TAKE OFF (PTO) SWITCH (P) The operator must be in the seat when engaging the
PTO or the engine will kill. Pulling the PTO switch
out engages (turns on) the PTO and starts the blades
or other attachment. Pushing the PTO switch in
disengages (turns off) the PTO and stops the blades
or other attachment.
NOTE: The PTO switch does not control
attachments powered by a separate engine.
At operator's right side
- Disengage the PTO whenever you stop or leave
the operator’s position
- Shut off engine with the key and remove the
spark plug wires before making adjustments or
unplugging a clogged mower.
- Do not engage the PTO until ready to start
mowing.
HOUR METER (M) - Records accumulated time
the machine is in operation and provides service
alerts. Push the release MODE button to toggle
between functions. Provided service alerts include
change engine oil and filter, change hydraulic oil,
and service air filter. When the service time is
approaching, an alert message will flash temporarily,
interrupting whatever mode the meter is in. This
will continue until the alert is reset. When the
service interval reaches "0" hours, the word "NOW"
replaces the hours remaining. To reset the service
alert, depress and hold down the mode button for 6
seconds while in the alert to be cleared.
15
CONTROLS
FastCat RZ
FUEL SELECTOR VALVE (U)
The fuel tank selector valve is located behind the
seat.
The fuel tank selector valve has three positions:
Off: The tank selector is off when the lever points
down. The selector should be off whenever the
machine is transported or stands unused for any
length of time. Shutting off the fuel supply avoids the
possibility of flooding should any dirt get under the
carburetor float needle. Leaving the tank selector in
either tank position can allow severe flooding, which
may ruin the engine by diluting the oil.
Right Tank: Fuel flows from the right tank when the
selector is turned 1/4 turn toward the right.
Left Tank: Fuel flows from the left tank when the
selector is turned 1/4 turn toward the left.
FOOT PEDAL LIFT LEVER (F) - Used to raise
the cutterdeck for curb climbing, blade changing and
lifting the deck close to the transport position. To
return to preset height of cut, lower foot pedal until
latch lever T contacts height of cut pin A.
16
CONTROLS
FastCat RZ
Reverse movement - To move the machine straight
back, pull both traction levers back equally from their
neutral position. Reverse speed increases as the
levers are moved back farther. Maximum reverse
speed is reached when the levers hit the rear of the
forward-reverse slot. When moving in reverse, pushing the levers forward slows the machine, and the
machine stops when the neutral position is reached.
Lift and traction levers
(operator's right side)
TRANSFER LATCH LEVER (T) - Used to secure the cutterdeck in transport position. To return to
preset height of cut, lower latch lever until latch lever
contacts height of cut pin A.
HEIGHT OF CUT PIN (A) - Sets height of cut
and allows easy return from transport to desired
height of cut. Raise the deck to transport using the
foot pedal and transfer latch lever T. Position pin A
in the hole corresponding to the desired height of cut.
Lower the latch lever until it rests on pin A.
TRACTION LEVERS (L) - Each of the two traction levers controls the drive wheel located on the
same side. They control the forward and reverse
movement of the machine, provide steering and also
provide dynamic braking.
The operator must be in the seat and the parking
brake must be OFF or the traction drive cannot be
engaged. To engage traction drive, move the traction
levers toward the center of the machine until they are
out of neutral lock slot S.
Forward movement - To move the machine straight
ahead, push both traction levers forward equally from
their neutral position. Forward speed increases as
the levers are moved farther forward from the neutral
position. Maximum forward speed is reached when
the levers hit the front of the forward-reverse slot.
When traveling forward, pulling the traction levers
rearward slows the machine, and the machine stops
when the neutral position is reached.
NOTE: Reverse is spring loaded to return to neutral.
This spring resistance may be felt when moving the
traction levers into reverse. When the levers are
released in reverse, spring tension will slowly return
them to the neutral position.
STEERING - To steer, move one lever forward and
one back.
Turns during forward movement:
– Right turn - move the right traction lever back
toward neutral to slow the right drive wheel.
– Left turn - move the left traction lever back toward neutral to slow the left drive wheel.
Turns during reverse movement:
– Reverse right turn - move the right traction lever
forward toward neutral to slow the right drive
wheel.
– Reverse left turn - move the left traction lever
forward toward neutral to slow the left drive
wheel.
Slow, sweeping turns are made with both traction
levers on the same side of neutral and slightly
apart. True zero radius turns about the center of the
machine are made by having one lever in reverse
while the other is in forward. By varying the relative
positions of the two levers, the rate of turn is varied to
suit the mowing situation.
Slow down before making sharp turns. The machine
is capable of turning very rapidly when the levers are
moved further apart from each other. Loss of control
and/or turf damage may result.
17
CONTROLS
FastCat RZ
PARKING BRAKE (R) - Pull the parking brake
lever up and back to put the parking brake ON. Push
it forward and down to put the parking brake OFF.
The parking brake must be ON to start the engine.
It must also be ON to keep the engine running if the
operator leaves the seat. The parking brake must be
OFF to keep the engine running when a traction lever
is moved out of neutral lock.
Parking brake in ON position
(operator's left side)
PUSHING THE MACHINE
The machine may be pushed with the engine off, the
parking brake off, and the bypass valves open.
To open the bypass valves, move the parking brake
to the OFF position, then lift and pull bypass control
rod C through the large opening D, until the control
rod stop is past the opening. Drop rod C into the
small opening to lock in place. Repeat for the other
bypass control rod.
To close the bypass valves, lift bypass control rod C
allowing the control rod stop to retract through the
large opening D.
18
PRE-OPERATION CHECK LIST
FastCat RZ
PRE-OPERATION CHECK LIST
(OPERATOR’S RESPONSIBILITY)
___ Review and follow all safety rules and safety
decal instructions.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check to make sure all shields and guards
are properly installed and in good condition.
Be sure that either the discharge shield or
complete vacuum attachment is installed.
___ Check that all hardware is properly installed.
and secured.
___ Check that equipment is properly and securely
attached to power unit.
___ Check to be sure engine is free of dirt and
debris. Pay particular attention to the cooling
fins, governor parts and muffler. Clean air
intake screen. Check air cleaner; service if
necessary.
___ Never allow riders.
___ Inspect area and remove stones, branches or
other hard objects that might be thrown,
causing injury or damage.
___ Clean area around oil fill dipstick. Remove
dipstick and check to be sure oil is in operating
range (between marks on dipstick). Add oil if
necessary but Do Not Overfill. Install dipstick
assembly firmly until cap bottoms out on tube.
Dipstick assembly must always be secured into
fill tube when engine is running.
___ Check all lubrication points and grease as
instructed in manual.
___ Check hydrostatic fluid level. Check to be sure
cooling fins on hydrostat are clean.
___ Perform a functional check of the safety
interlock system each time you operate the
unit.
19
OPERATION
FastCat RZ
FUELING
- Fill fuel tank with good quality, clean, unleaded
regular gasoline. Refer to engine manual.
- Use a funnel to avoid spilling.
OPERATOR PRESENCE
INTERLOCK SYSTEM
To start the engine:
- The PTO switch must be OFF.
- Both traction levers must be in the neutral lock
position.
WARNING
- The parking brake must be ON.
To operate the machine:
1. The operator must be in the seat or engaging the
PTO will kill the engine.
TO CHECK OR ADD FUEL:
– Do it outdoors
2. The parking brake must be OFF and the operator must be in the seat, or moving a traction lever
from the neutral lock position will kill the engine.
– Do not smoke
– Stop engine; allow to cool
– Fill to one inch below bottom
of filler neck
STARTING THE ENGINE
– Do not overfill
– Clean up spilled fuel
BEFORE STARTING THE ENGINE
- Be familiar with all controls, how each functions
and what each operates.
- Check the engine oil level and add if necessary.
Using the fuel selector valve, select which tank
will supply fuel
- Choke: For cold starts, set the throttle lever to the
half-open position and pull the choke out to the
ON position. For warm starts set the throttle to
the half-open position and the choke to the OFF
position.
20
1. Turn the key to operate the electric starter to start
the engine. Release the key when the engine
starts.
2. If the engine does not start immediately, do not
crank for more than 10 seconds at a time. Allow
60 seconds for the starter motor to cool down
between starting attempts to prevent the starter
motor from burning out.
3. If the choke is ON when the engine starts,
gradually back it off until the engine runs with no
choke at all.
OPERATION
FastCat RZ
OPERATING NOTES
DRIVING
- Practice at slow engine and travel speeds with the
PTO off until fully familiar with the controls.
1. With the PTO disengaged, move the parking
brake to OFF.
- For normal cutting the throttle should be set at the
full open position. By using the traction levers to
speed up or slow down the machine during use,
maximum control and cutting efficiency can be
maintained.
2. - Using the machine at less than full throttle in
heavy conditions will cause the engine to labor
and result in excessive wear.
4. Steering - Move one lever forward and one back.
Move both traction levers out of neutral lock.
3. Push both traction levers forward evenly to
drive forward in a straight line. Pull both traction
levers back evenly to drive backward in a straight
line.
Turns during forward movement:
-
Right turn - move the right traction lever back
toward neutral to slow the right drive wheel.
-
Left turn - move the left traction lever back toward neutral to slow the left drive wheel.
Turns during reverse movement:
-
Reverse right turn - move the right traction lever
forward toward neutral to slow the right drive
wheel.
-
Reverse left turn - move the left traction lever
forward toward neutral to slow the left drive
wheel.
Use caution when making turns. Slow down before
making sharp turns to help maintain control and to
prevent torn turf from skidding or spinning tires. To
help prevent turf damage, keep both drive tires moving whenever a turn is made.
TIP: The best way to make a sharp "zero" turn is to
come to a stop, get the machine moving in reverse
with both drive wheels and then power the machine
around with the outside wheel. This technique keeps
the drive tires turning and results in less turf damage.
21
OPERATION
FastCat RZ
CUTTING
1. Place the discharge chute in the down position or
correctly fit a grass collector or mulcher plate.
DANGER
2. Sit in the seat.
3. Start the engine.
4. Turn the blades on by pulling up on the PTO
switch. Do not start the blades at full throttle.
Instead, use the slowest throttle setting that will allow the engine to pick up the blade load to reduce
the wear on the belts and electric clutch.
5. After the blades are rotating, set the throttle to
maximum. Use the traction levers to obtain the
required cutting speed, to steer around obstacles
and to turn at the end of a cut.
ROTATING BLADES
– KEEP HANDS AND FEET AWAY.
– STOP ENGINE AND LET BLADES STOP
BEFORE REMOVING GRASS COLLECTOR OR UNCLOGGING.
WARNING
THROWN OBJECTS
CUTTING TIPS
- When mowing large areas, start by turning to the
right so that clippings will be discharged away
from shrubs, fences, driveways, etc. After two or
three rounds, mow in the opposite direction, left
hand turns, until finished.
- If grass is extremely tall, it should be mowed
twice, the first cut relatively high, the second cut to
the desired height.
- Use the left side of the mower for trimming.
- Choose cutting directions so that clippings are
thrown onto areas that already have been cut.
This method results in the most even distribution
of clippings and more uniform, better appearing
cuts.
- Use a different mowing pattern each time where
possible. This helps prevent rutting and leads
to a more uniform cut by keeping the grass from
always laying the same way.
22
– KEEP AREA CLEAR OF PEOPLE
AND PETS.
– REMOVE OBJECTS BLADE MAY
STRIKE AND THROW.
– STOP BLADES TO CROSS GRAVEL
AREAS
– DO NOT OPERATE WITHOUT CHUTE,
MULCHER OR ENTIRE GRASS
CATCHER IN PLACE.
MAINTENANCE CHART
FastCat RZ
MAINTENANCE
OPERATION
Maintenance is an ongoing job. These intervals are maximum times betw een
maintenance operations. Perform more often under severe conditions.
FIRST 5
HOURS
BEFORE
EACH
U SE
EVERY
25
HOURS
EVERY
50
HOURS
EVERY
100
HOURS
EVERY
200
HOURS
YEARLY
ENGINE
Consult the engine manual for additional information and instructions
Check/Top Up
Oil Level
X
C h eck F o r L eaks
X
Clean Air Intake
Screen
X
Clean Air Cleaner
Precleaner
Clean Air Cleaner
Element
X
Clean Cooling Fins
Change Oil And
Filter
X
See engine manufacturer's manual
X
Check/Replace
Spark Plugs
X
TRANSAXLE
Check Oil Level
X
X
C h eck F o r L eaks
X
X
Change Oil And
Filter
X
MACHINE
Check Interlock
Operation
X
Check Tire
Pressures
X
Check/Top Up
Battery
Lubricate All Points
X
X
23
MAINTENANCE RECORD
FastCat RZ
NOTES
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
GENERAL
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
D ATE
C h ec k T i r e P r es s u r es
L u b r i c at e A l l P o i n t s
C h ec k N u t s & B o l t s
ENGINE
Ch ec k Oil L ev el
Ch an g e Oil
C l ean
A i r C l ean er E l em en t
C l ean C o o l i n g F i n s
R ep l ac e
A i r C l ean er E l em en t
Clean & Gap
S p ar k P l u g s
TR A N S A X L E
Ch an g e Oil An d Filt er
NOTE: Af t er f ir s t 5 h o u r s o f o p er at io n c h an g e en g in e o il an d f ilt er.
24
HRS
DATE
HRS
MAINTENANCE
FastCat RZ
CHECK DAILY
Operator Presence Interlock System - Start Operation
For the engine to crank, the parking brake must be on, the PTO (blades) off and traction levers in the neutral
lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the
blades on, and either traction lever out of neutral lock.
Operator Presence Interlock System - Run Operation
The operator must be in the seat for the engine to run with the parking brake off, the traction levers moved out
of the neutral lock position, or the blades on. To check:
1. Start the engine and run at 1/2 throttle with the operator on the machine but raised off the seat.
2. One by one: move the parking brake to the OFF position, traction levers out of the neutral lock position
(check each independently), and turn the blades on. Each check should kill the engine after 1/2 second.
(A 1/2 second delay is built into the system to prevent engine cutout when traversing rough terrain.)
Repair machine before using if the Operator Presence Interlock System does not operate correctly in start or
run. Contact your authorized Schiller Grounds Care, Inc. dealer.
Hardware
Tighten any nuts and bolts found loose. Replace any broken or missing cotter pins. Repair any other problems before operating.
Tire pressure
Tires should be kept inflated to 12 lbs/in2 (0.8 kg/cm2). Improper tire inflation can cause rapid tire wear and
poor traction. Uneven inflation can cause uneven cutting. Over inflation of caster tires can cause casters to
"wobble" on hard surfaces.
BATTERY
Battery acid is caustic and fumes
are explosive and can cause serious injury or death.
4. Check the electrolyte level every 100 hours of
operation or yearly, whichever comes first. Top
off with distilled water if necessary.
Use insulated tools, wear protective glasses or
goggles and protective clothing when working with
batteries. Read and obey the battery manufacturer’s
instructions.
NOTE: Sealed batteries cannot be checked or
topped off.
Be certain the ignition switch is OFF and the key has
been removed before servicing the battery.
1. Verify battery polarity before connecting or disconnecting the battery cables.
2. When installing the battery, always assemble
the RED, positive ( + ) battery cable first and the
BLACK ground, negative ( - ) cable last.
5. Clean the cable ends and battery posts with steel
wool. Use a solution of baking soda and water
to clean the battery. Do not allow the solution to
enter into the battery cells.
6. Tighten cables securely to battery terminals and
apply a light coat of silicone dielectric grease to
terminals and cable ends to prevent corrosion.
Keep terminal covers in place.
3. When removing the battery, always remove the
BLACK ground, negative ( - ) cable first and the
red, positive ( + ) cable last.
25
MAINTENANCE
FastCat RZ
LUBRICATION
Every 50 hours of operation, lubricate the following points (1-3) with grease:
1. Deck lift lever (1 point)
2. Deck lift pivots (4 points)
3. Pull arms (2 points located at the front of the cutterdeck)
4. Caster wheel pivots (2 points)
(Lubricate every 500 hours or once a year)
NOTE ON BLADE SPINDLES - The blade spindles on these machines use a
superior sealed bearing that does not require relubrication.
26
MAINTENANCE
FastCat RZ
ENGINE OIL
Do not perform engine maintenance without the
engine off, spark plug wires disconnected and PTO
disengaged.
AFTER FIRST FIVE (5) HOURS
While the engine is warm:
1. Release the oil drain hose assembly from the
engine clip J. Lay hose assembly over the frame
edge or through the frame cutout, which ever is
most convenient.
2. Remove the rubber cap D from the tip of the
hose assembly and turn the drain valve to allow
oil to drain from the engine. Dispose of used oil
in accordance with local requirements.
3. Clean drain valve and tighten the plastic portion
of the drain valve back into the metal portion of
the valve. Replace rubber cap over the tip of the
valve. Replace hose assembly back into engine
clip.
4. Change oil filter.
5. Fill the crankcase with fresh oil to the full mark.
Do not overfill. See engine manual for oil
specifications.
DAILY
1. Check oil level with the dipstick.
2. If oil is needed, add fresh oil of proper
viscosity and grade. See engine manual for oil
specifications. Do not overfill.
3. Replace dipstick before starting engine.
PERIODIC OIL CHANGES
1. See engine manual for oil and filter change intervals after the break-in period.
2. Follow instructions for first oil change, above.
SPARK PLUGS
Remove each plug and check condition.
-
Good operating conditions are indicated if the plug has a light coating of grey or tan deposit.
-
A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both
may be caused by a clogged air cleaner or improper carburetor adjustment.
-
Do not sandblast, wire brush or otherwise attempt to repair a plug in poor condition. Best results are
obtained with a new plug.
-
Set plug gap as specified in engine manual..
FUEL FILTER
An in-line fuel filter is located in the fuel supply line. Inspect at every oil change to make sure it is clean and
unobstructed. Replace if dirty.
27
MAINTENANCE
FastCat RZ
AIR CLEANER
KAWASAKI MODELS:
Clean and replace the air cleaner element as specified in the service chart. Uneven running, lack of
power or black exhaust may indicate a dirty air
cleaner.
KAWASAKI MODELS
To replace air cleaner:
1. Lift cover A.
2. Loosen clamp B and remove existing air cleaner
element C.
3. Insert new element C and tighten clamp B.
Close cover A.
B&S MODELS
To replace air cleaner:
1. Lift clamps on cover A and remove.
2. Remove exisitng air cleaner element B.
3. Insert new element B and replace cover A and
clamp tightly.
Every 100 hours (more often under very dusty or dirty
conditions), check the paper cartridge.
– Clean by tapping gently.
– Do not wash the cartridge or use compressed air
which can cause damage.
– Replace when cartridge is dirty, bent or
damaged.
28
B& S MODELS:
MAINTENANCE
FastCat RZ
ENGINE COOLING
Continued operation with a clogged cooling system
will cause severe overheating and can result in engine damage.
-
Daily: Clean air intake screen V.
-
Every 100 hours: Clean cooling fins beneath
blower housing H with reference to information in
the engine manufacturer's manual.
SPECIFIC TORQUES
B LADE BOLTS
70 FT-LBS (95 Nm )
WHEEL HUB NUTS
150 FT-LBS (203 Nm)
ENGINE CRANKSHAFT BOLT
50 FT-LBS (68 Nm )
TRANSAXLE PULLEY NUT
28.3 - 41.6 FT-LBS (38 - 56 Nm)
TRANSAXLE DRAIN PLUG
15 - 20 FT-LBS (20 - 27 Nm)
TRANSAXLE FILTER
130 - 150 in-lbs (14.6 - 16.9 Nm)
PURGING TRANSAXLES
Due to the effects air has on efficiency in hydrostatic
drive applications, it is critical that it be purged from
the system.
These purge procedures should be implemented any
time a hydrostatic system has been opened to facilitate maintenance or any additional fluid has been
added to the system.
Purging may be required if the unit shows any of the
following symptoms:
- Noisy operation.
- Lack of power or drive after short term use.
- High operation temperature, excessive oil expansion.
1. Check the transaxle fluid, fill to proper level, if
required.
2. Raise the drive wheels off the ground. Support
unit with jackstands or other suitable means.
3. With the bypass valves open, and the engine
running, slowly move the control levers in both
forward and reverse directions 5 to 6 times. As
air is purged from the unit, the oil level will drop.
4. With the bypass valve closed, and the engine
running, slowly move the control levers in both
forward and reverse directions 5 to 6 times.
5. Stop engine. Check the transaxle fluid level, add
fluid as required.
6. It may be necessary to repeat steps 3-5 until all
the air is completely purged from the system.
When the transaxle moves forward and reverse
at normal speed, purging is complete.
29
MAINTENANCE
FastCat RZ
TRANSAXLES
Inattention to proper safety, operation, or
maintenance procedures could result in personal
injury, or damage to the equipment. Schiller
Grounds Care, Inc. recommends returning the
machine to your authorized Schiller Grounds
Care, Inc. dealer for service or repair.
Perform transaxle maintenance with the engine off,
spark plug wires disconnected and PTO disengaged.
TRANSAXLE FLUID CHANGE
Change the transaxle fluid every 200 hours of
operation. It is essential that the exterior of the
transaxle be free of debris, prior to fluid maintenance.
1. Remove the three 1/4" filter guard screws and
filter guard A. Remove the oil filter B from the
transaxle and discard. Dispose of used oil in accordance with local requirements.
2. Wipe the filter base surface off and apply a film
of new oil to the gasket of the new replacement
filter. Install the new filter by hand, turn 3/4 to
one full turn after the filter gasket contacts the
filter base surface.
3. Re-install the filter guard and torque the three
screws to 65 in. lbs. each.
4. Remove cap C, fill the transaxles through the
expansion tank D with approximately 2 quarts of
SAE 20W-50 engine oil PER TRANSAXLE.
Do not overfill! If you overfill the transaxle while the unit
is "cold", it may overflow as it reaches normal operating
temperatures. The oil level should not be above the
manufacturer's suggestions. This will allow the space
needed for the oil to expand as it warms up.
5. After starting engine, check the fluid level and
continue to add oil to overflow tank D to fill line
on tank.
6. Purge the transaxles, following the purging procedures on Page 29.
30
MAINTENANCE
FastCat RZ
BLADE REMOVAL
BLADE BALANCE
Follow these instructions to prevent injury during
blade removal:
1. Loosen with a box wrench or a socket and long
breaker bar. To gain additional leverage, slip a
long pipe or thick-walled tube over breaker bar or
wrench.
2. Insert wood block A as shown, with grain
perpendicular to blade, to prevent blade from
turning when loosening.
3. Wear thickly padded gloves. Keep hands clear
of blade path. Blades may rotate when bolt
releases.
Blade balance must be maintained at 5/8 oz-in (19.4
g-cm) or less. Failure to keep blades balanced
causes excess vibration, wear, and shortened life of
most components of the machine.
To balance a blade:
1. Sharpen blade first.
2. Balance the blade at the center.
3. Attach a 1/8 oz (3.9 g) weight at a distance 5"
(127 mm) from center on the light end. This
should make the light end the heavy end:
- If it does, the blade is balanced.
- If does not, file or grind the heavy end until
the addition of the weight makes the light end
the heavy end.
BLADE INSTALLATION
1. Wear thickly padded gloves to prevent cuts from
the sharp blade.
2. Insert the blade bolt, in order, through the conical
washer (cup side toward the blade, as shown),
the blade, and the blade spacer.
3. Install assembly on the blade spindle.
4. Torque the blade bolt to 70 ft-lbs.
SHARPENING
Blades may be sharpened by filing or grinding.
- Inspect blades before sharpening.
- Replace bent or cracked blades.
- Replace blades when the lift portion has worn
thin.
o
- Maintain cut angle at 30 .
- Do not overheat blades when sharpening.
- Always use Schiller Grounds Care, Inc. blades.
Use of another manufacturer’s blades may be
dangerous.
31
ADJUSTMENTS
FastCat RZ
DECK LEVELING
1. Park the machine on a smooth, level surface.
Raise the deck to the transport position.
2. Lower the deck onto a set of equal height blocks
under the rear corners of the deck. Place another set of blocks under the front of the deck so
that the deck top is pitched forward 1/8".
NOTE: The front and rear of the deck are at different
heights.
3. Measure the height of the blade cutting edge
above the ground. Remove pin B and set the
height of cut lever E to that height
4. Loosen nuts on bolts G. Move bolts in slot to
remove slack in chain. Tighten nuts on bolts G.
A 1/8" forward pitched deck provides the best horsepower.
A level deck provides the best quality of cut.
A 1/8" rearward pitched deck provides the best striping.
Certain grass types and conditions may vary.
HEIGHT OF CUT
The height of cut is set by moving height of cut pin C
to the hole designated for the height of cut desired.
To change the height of cut:
1. Lift the deck to the highest position using the foot
lift pedal.
2. Move pin C to the selected hole.
3. Lower the deck until the latch lever T is stopped
by the pin.
NOTES:
– Height of cut may vary due to the amount of
tread on the tires, tire diameter or inflation pressure.
– For best results, adjust the rear deck rollers for
the height of cut to be used (see below).
DECK ROLLERS
The deck rollers are adjustable up and down to
provide improved deck flotation and scalping protection at various heights of cut. They are not intended
to ride continuously on the ground. Adjust no closer
than 3/8" (10mm) to the ground.
Height of cut ranges for roller adjustment
32
ADJUSTMENTS
FastCat RZ
`
PARKING BRAKE
NOTE: There are 2 brakes, 1 on each transaxle.
The parking brake should keep the machine from
moving. To check the parking brake, park the machine on a level surface, open the bypass valves and
set the parking brake to ON. Attempt to move the
machine forward and backward by pushing it. If the
machine moves, adjust the parking brake linkage as
follows:
1. Move the machine to a flat horizontal surface.
2. Grip the flats on the brake rod A. Tighten nut
B on the brake rod until you run out of threads.
See Figure 1 for detailed view.
3. Move the parking brake handle to the OFF
position.
4. Loosen nut X.
FIGURE 1
5. Hold brake arm in the OFF position as shown in
Figure 2.
6. Adjust swivel U until swivel stud meets brake arm
hole in the OFF position.
7. Insert cotter pin into formed end of linkage rod U.
8. Tighten nut X.
9. Repeat Steps 1-8 on the opposite side.
FIGURE 2
33
ADJUSTMENTS
FastCat RZ
HYDROSTATIC TRANSAXLE ADJUSTMENTS
A turnbuckle style hydrostat neutral adjustment is
provided.
Neutral:
1. Support the machine with the rear wheels off
the ground. Use jackstands or equivalent support. Do not rely only on mechanical or hydraulic
jacks.
2. Move the traction levers out into the neutral lock
position and raise the seat.
3. Disconnect the seat switch wire and temporarily
connect the two terminals with jumper wire J as
shown.
4. Start the engine and run at low speed.
5. Move parking brake to the OFF position.
6. Loosen jam nuts K at both ends of the control
rod L.
7. Rotate the control rod until the corresponding
wheel stops turning. Lock the control rod jam
nuts. Run the engine up to high idle and stroke
the traction levers forward and back to check the
adjustment. Move traction levers back to neutral
and readjust if necessary.
8. Repeat steps 6 and 7 for the opposite side.
9. Remove the jumper wire and reconnect the seat
switch.
34
BELT REPLACEMENT
FastCat RZ
NOTE: Always use Schiller Grounds Care, Inc. replacement belts, not general purpose
belts. Schiller Grounds Care, Inc. belts are specially designed for use on this mower and
will normally last longer.
CUTTERDECK BELT
1. Remove floorplate.
2. Set the cutterdeck in a middle height-of-cut position.
3. Use a 3/8" ratchet and extension to back
tensioning idler off to remove belt from idler.
Remove belt from cutterdeck pulleys.
NOTE: Use the 3/8" ratchet in the square hole A on
the idler.
4. Remove belt from clutch pulley.
5. Install the new belt by performing these steps in
reverse order.
3 SPINDLE DECK
BELT TENSION
NOTE: 61" cutterdeck may require tension spring
adjustment after belt installation. See Belt tension
below.
2 SPINDLE DECK
BELT TENSION FOR 61" DECK
All belts are tensioned by spring loaded idlers and do
not require any adjustment except for the 61"
cutterdeck. Use the eyebolt to adjust the spring
length to be between 6 3/4" - 7 1/2" as pictured.
35
BELT REPLACEMENT
FastCat RZ
HYDRO TRANSAXLE DRIVE BELT
1. Remove cutterdeck belt (see cutterdeck belt
replacement).
2. Disconnect wire I at clutch M. Remove bolts J
and remove torque restraint.
3. Using a ratchet with a 9/16" socket, place over
nut at location P. Use the ratchet to rotate it
enough to remove the transaxle drive belt.
4. Install a new transaxle drive belt by performing
these steps in reverse order.
5. Inspect the fans. Replace if worn or damaged.
Torque transaxle pulley nut to 28.3-41.6 ft-lbs
(38-56 Nm).
6. Reinstall cutterdeck belt (see cutterdeck belt
replacement).
36
PARTS SECTION
FastCat RZ
PARTS
SECTION
37
FRAME-ENGINE/CLUTCH ASSY
FastCat RZ
FIGURE 1
INCLUDED W/ENGINE
29
KAW ENGINE B & S ENGINE
ONLY
ONLY
10
16
15
17
1
16
JUMPER HARNESS
27
26
3
13
27
21
24
28
22
23
4
25
2
11
18
30
8
5
19
14
7
12
9
20
38
6
10
FRAME-ENGINE/CLUTCH ASSY
FastCat RZ
FIGURE 1
ITM PART NO.
DESCRIPTION
1 4166966
4166965
38666
4164537
4167145
4168906
ENGINE-FR651V KAW
ENGINE-FR691V KAW
FILTER-FUEL
FILTER-OIL
FILTER-AIR (FR651V)
FILTER-AIR (FR691V)
QTY
1
1
4165984
ENGINE-627cc VANGRD B&S 1
38666 FILTER-FUEL
4164152 ELEMENT-AIR
4164153 FILTER-OIL
(USED ON MODEL 942311H)
2 4164385
MUFFLER -KAW
1
(USED ON MODELS 942315H & 942316H)
ITM PART NO.
DESCRIPTION
QTY
18 4144112.7 WLDMT-CLUTCH BRACKET
194163309 PULLEY-ENGINE
20 64123-78
BOLT-HEX 7/16-20X2-1/2
(USED ON 942315H & 942316H)
64123-55
BLT-HEX 7/16-20X3
(USED ON MODEL 942311H)
1
1
1
21 69053-13
1
HOSE-HTDRO, 3/8X14"
1
(ITEMS 22-24 USED ON KAW ENGINES ONLY)
22 64266-02
NUT-FL LOCK M8-1.25
2
23 64263-002 BLT-FLG HD M6-1.0 X 16
6
24 4164442.7 BRKT-MUFFLER LH
1
*4164443.7 BRKT-MUFFLER RH
1
4163913 MUFFLER-B&S
(USED ON MODEL 942311H)
1
2511061-7061 GASKET-MUFFLER
(AVAILABLE FROM KAWASAKI DEALER)
3 64152-23
1/4-20X3/8 LG SP SCREW
438665
SOLENOID
(ITEMS 3 & 4 USED ON 942311H)
2
1
806425 GASKET-MUFFLER
(AVAILABLE FROM B&S DEALER)
5 38304-03
BRG-FLANGED PLASTIC
6 2721331.7 WLDMT-CLUTCH STOP
764265-04 LOCKNUT-M8-1.25
8 64164-12
KEY-1/4X1/4X1 SQ END
9 64006-06
LOCKWASHER-HEL 7/16
10 64205-001 BLT-MET M8-1.25X20
11 4167267
S-FRAME W/ LABELS
12 4144116
CLUTCH-ENGINE PULLEY
1348412-01 CLAMP
14 64197-005 BLT-TDFM 3/8-16X1-1/4
(USED ON B & S MODELS ONLY)
64123-70
BLT-HEX 3/8-16X1-1/2 (USED ON KAWASAKI MODELS ONLY)
1
1
2
1
1
3
1
1
1
4
15
16
17
2
26 4164251
VAILVE-OIL DRAIN
2788042-03 CLAMP-HOSE
28 4164252-001FITTING-3/8NP TO BARB
294162803.7 DEFLECTOR-AIRFLOW
(USED 942311H ONLY)
1
2
1
1
30 64006-03
LOCKWSHR-3/8 HELICAL
(USED KAWASAKI MODELS ONLY)
4
* NOT ILLUSTRATED
4
(ITEMS 15-16 USED ON B&S ONLY)
64006-02
LOCKWASHER-HELICAL 5/16 1
64163-55
WSHR .328X.75X14 GA
1
64223-11
SCH CAPSCREW M8-1.25X16 1
39
TRANSAXLE ASSY
FastCat RZ
FIGURE 2
10
23
8
22
48
15
1
41
41
67
40
15
30
3
2
28
29
31
18
11
19
CUTTERDECK
16
38
37
36
17
39
13
35
9
14
44
43
42
12
44
32
43
20
33
27
4
17
24
RIGHT
TRANSAXLE
PULLEY
5
17
15
21
24
34
16
LEFT
TRANSAXLE
PULLEY
BELT DETAIL
40
TRANSAXLE ASSY
FastCat RZ
FIGURE 2
ITM PART NO.
DESCRIPTION
1 4167267
S-FRAME W/LABELS
2 4162973
SHAFT-PULLARM MOUNT
3 4163957.7 WLDMT-PULL ARM
44163819 ARM-CONTROL
54163493 AXLE-LH
(INCLUDES ITEMS 4, 25, 26, 27, 32)
QTY
1
1
2
2
1
664163-29 WASHER
2
7 64123-68
BOLT-HEX 5/16-18X1
2
8 64163-03
WSHR .256ID X.62OD X 18 GA.2
9 64270-01
BOLT-MET, HEX M10-1.5x30 1
10 64262-002 BLT-FLG HD 1/4-20 X 3/4
2
11 64163-55
WASHER .328X.75X14 GA
6
124164128 SPRING-TENSION
1
13 64123-67
BLT-HEX 3/8-16 X 2
1
14 4128001
END CAP-24 X 7
1
15 64268-02
NUT-FL NYLON LOCK 5/16-18 10
16 2228016
PULLEY-IDLER PUMP
1
17 64163-31
WASHER, 25/64X1X12
8
18 64123-55
BLT-HEX 5/16-18X3
4
19 64268-03
NUT-FL NYLON LOCK 3/8-16 5
204163494 AXLE-RH
1
(INCLUDES ITEMS 4, 25, 26, 27, 32)
214143636 BELT-TRANSAXLE
22 4167239
ROD-BATTERY CLAMP
234167215 BATTERY
24 64123-88
BLT-HEX 3/8-16X2-3/4 25*4142045-06 FILTER-TRANSAXLE
26*4163819
SPRING-CONTROL ARM
274163820 ARM-BRAKE
4164862 CLIP-RETAINING
(USE WITH BRAKE ARM)
ITM PART NO.
DESCRIPTION
QTY
34 64187-03
WHEEL NUT 1/2-20
35 4133302
S-ASSY-IDLER ARM PUMP
(INCLUDES ITEMS 36-38)
8
1
36 4128004
BEARING-BALL 10X26X8
37 64144-40
SNAP RING-26MM INTERNAL
384128000 SEAL-16X26X7
3964163-61 WASHER
404167258.7 TRAY-BATTERY
41 64197-022 BLT-TDFM 3/8-16 X 3/4
42 4163264-01 ADAPTER-90 #6 MAORB/#6 FORB
43 4163307
ASSY-EXPANSION TANK
444142808-01CAP-HYDROTANK
45*4163772-01 GUARD-FILTER RH
46*4164227
CHARGE PUMP COVER KIT
47*4163771-01 GUARD-FILTER LH
48 64025-01
NUT-1/4-20 HEX
2
1
1
1
1
3
1
2
2
1
1
1
2
* NOT ILLUSTRATED
1
2
1
4
2
2
2
2
28
29
30
31
32
33
64123-168 BLT-HEX 5/8-11X2-1/2
2
64163-93
WSHR-.635 X 1.12 X.062
4
85010N
ZERK, 1/4-28
4
64229-06
LOCKNUT, NYLON 5/8-11
2
4164048
KIT-FAN/PULLEY TRANSAXLE 2
4142752
ASSY-WHEEL 20X8.0-10
2
4142752-01 TIRE-20X8 PLY MULTI-TRAC 4132433 ASSY-WHEEL 20X10-10
(USED ON 42" DECK MODELS)
4167019
ASSY-WHEEL, 22 X 11.0-10
4167019-01 TIRE-22X11.0-10 2PLY
4155841-01 WHEEL-10 X 7
(USED ON 52" & 61" DECK MODELS)
2
41
FUEL TANK/BUMPER & CONTROL PANEL
FastCat RZ
FIGURE 3
29
19
8
12
6
7
14
14
5
11
22
30
13
10
9
2
15
3
16
17
15
32
16
17
26
28
31
15
35
34
24
25
27
33
23
4
21
21
18
42
FUEL TANK/BUMPER & CONTROL PANEL
FastCat RZ
FIGURE 3
ITM PART NO.
DESCRIPTION
QTY
1 4167267
S-FRAME W/LABS
2 4165504
TANK-FUEL RH 3 4165503
TANK-FUEL LH
44163041.7 BUMPER
(USED ON 52" DECKS ONLY)
4164221.7BUMPER
(USED ON 61" DECKS ONLY)
1
1
1
1
5 4166245
6 128010-03
7 128010-01
82721505
9 4165291
102188178
11 128010
12 64152-46
13 64025-15
14 64262-001
15 64123-50
1664006-03
1764163-69
18 64262-010
194165120
20*4144213
21 64268-03
22118020-17
2364229-02
24 48228-12
25 64123-54
26 64123-15
27 64229-03
28 4163880.7
29108009-09
30 64025-04
31 4163895.7
32 4164022.7
1
1
1
1
2
1
1
2
2
4
18
10
10
4
1
2
4
1
2
2
2
4
8
2
1
1
1
1
S-CONTROL PANEL S-COVERED KEY
S-KEY SWITCH NUT 5/8-32
SWITCH-PTO
CAP-FUEL TANK
SWITCH-RETAINER
SWITCH, KEY
SCREW-SLT HH 10-24X1/2
NUT-HEX #10-24 KEPS
BLT-FLG HD 1/4-20 X 1/2
BOLT-3/8-16X1 HEX
WASHER-3/8
WASHER-FLAT
BLT-FLG HD 3/8-16 X 3/4
METER-HOUR
TUBE-FUEL FEED
NUT-WLF 3/8-16
CONTROL-THROTTLE
LOCKNUT-5/16-18
CLAMP-3/4 CLIP
BLT-HEX 5/16-18X3/4
BLT-HEX 3/8-16X3/4
NUT-NYLON LOCK 3/16-18
BRKT-TANK MOUNTING
CABLE-CHOKE
NUT-HEX 3/8-24 CHANNEL-TANK SPACER, LH
CHANNEL-TANK SPACER, RH
ITEMS 33-35 USED ON 61" MODELS ONLY
33 64262-018 BLT-FLG HD 3/8-16 X 1-3/4
344163905.7 PLATE-WEIGHT
354163901.7 WEIGHT-COUNTER
ITM PART NO.
DESCRIPTION
QTY
1
4
1
1
* NOT ILLUSTRATED
43
FUEL VALVE & COVER PLATE
FastCat RZ
FIGURE 4
13
13
6
6
14
12
16
12
16
6
16
18
15
17
9
TO
ENGINE
6
3
6
10
10
8
7
2
7
11
5
4
6
1
7
6
TO
ENGINE
44
11
FUEL VALVE & COVER PLATE
FastCat RZ
FIGURE 4
ITM PART NO.
DESCRIPTION
QTY
1
2
4167267
S-FRAME W/LABS
4165504
TANK-FUEL RH BOBCAT
(INCLUDES 10-13, 19-21)
1
1
3
4165503
TANK-FUEL LH BOBCAT
(INCLUDES 10-13, 19-21)
1
4
5
6
7
8
9
10
11
12
13
14
15
64197-001
4146655.7
88042N
4162977-001
2188161
4165291
4132325
4165667
4165387
4165763
4165863
4165864
BLT-TDFM 5/16-18X3/4
COVER-FRAME, REAR
HOSE CLAMP
HOSE-1/4 FUEL LINE 24"
VALVE-TANK SELECTOR
CAP-FUEL TANK
GROMMET-FUEL TANK
FITTING-BARBED 90 DEG
GROMMET-ROLL OVER
ROLLOVER VENT
TEE-FITTING 1/4"HOSE
FTTNG-HOSE 1/4" TO 3/16"
4
1
12
3
1
2
2
2
2
2
1
1
HOSE-FUEL LINE
HOSE-FUEL LINE
CLAMP
FUEL-LINE TANK
FILTER-FUEL
CLAMP-FUEL
3
1
2
2
2
2
16 4162977-020
17 4162989-001
1888042-01
19* 4165692-01
20*4165668
21*4166704
ITM PART NO.
DESCRIPTION
QTY
45
DECK LIFT ASSEMBLY
FastCat RZ
FIGURE 5
28
25
1
32
9
26
8
24
20
34
11
22
30
33
31
11
21 27
29
6
6
14
7
19
16
18
15
2
5
14
14
4
14
23
3
16
17
2
13
15
14
14
12
12
11
11
CUTTERDECK
46
17
16
25
9
10
19
DECK LIFT ASSEMBLY
FastCat RZ
FIGURE 5
ITM PART NO.
DESCRIPTION
QTY
1 4167267
S-FRAME W/LABS
2 64205-060 BOLT-MET M12-1.75X50
3 4167796.7 WLDMT-DECKLIFT, FRONT
4 4163894.7 WLDMT-DECKLIFT REAR
5 4109960
WLDMT-DECK LIFT ROD
6 64221-02
E-RING .250
7 4163891.7 BRKT-LIFT LINK 84167151 GRIP
9 64123-50
BOLT-HEX 3/8-16X1
10 85010N
ZERK, 1/4-28 STR
11 64229-03
LOCKNUT-NYLON 3/8-16
12 2182356.7 BRACKET-SHAFT HANGER
13 64205-029 BLT-MET M12X1.75X40
14 64246-04
NUT-WHIZ M12-1.75
15 2188127
CHAIN-6.35 (.250) 5 LINKS
1664163-65 WASHER-.890X1.375X18GA
1764221-04 E-RING.875
18 4167017.7 BRKT-OUTER DECK LIFT
192183071-03SPACER-15.88X10.32X24
20 4167111.7 LEVER-DECK LIFT
21 64268-02
NUT-FL NYLON LOCK 5/16-18
22 64188-76
PIN-CLEVIS, 1/2 X 1-3/8
23 4139785
MAT-FOOT LIFT
244167108.7 ARM-LATCH
25 64123-67
BLT-HEX 3/8-16X2
26 4167103
LABEL-H.O.C. OUTER, 27 4162904.7 WLDMT-LVR STOP LATCH
2864163-31 WASHER
29 64175-05
PUSHNUT-1/2 DIA
30 64123-47
BLT-HEX 5/16-18X1-1/4
31 4167018
ASSY, PIN & LANYARD
32 4167104
LBL-HT CUT INNER
334167138 SPRING-TORSION
34 64018-3
BLT-CRG 3/8-16X1
ITM PART NO.
DESCRIPTION
QTY
1
4
1
1
2
2
1
1
15
5
18
4
4
16
4
10
5
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
47
CASTER ASSEMBLY
FastCat RZ
FIGURE 6
48
CASTER ASSEMBLY
FastCat RZ
FIGURE 6
ITM PART NO.
DESCRIPTION
QTY
1 4167267
S-FRAME W/LABS, 2 4162986
DUST COVER
385010N ZERK-1/4-28
4 64025-20
NUT-HEX 3/4-16 SLOT U
564163-26 WASHER
6 48043-03C CUP-OUTER BEARING
7 48043-04C CONE-OUTER BEARING
848480
SEAL
94143675.7 WLDMT-CASTER
(FOR 42" DECK MODELS)
2721306.7WLDMT-CASTER
(FOR 52" & 61" DECK MODELS)
1
2
2
2
2
4
4
2
2
10 64229-07
NUT-NYLON LOCK 3/4-10
(USED ON 52" & 61" MODELS ONLY)
64229-06
NUT-NYLON LOCK 5/8-11
(USED ON 42" MODELS ONLY)
11 64123-215 BLT-HEX 3/4-10X7-1/2
(USED ON 52" & 61" MODELS ONLY)
64123-212 BLT-HEX 5/8-11X6
(USED ON 42" DECKS ONLY)
122722231 SPACER-END
13 2722233
WHEEL-11"ASSY-LT TYPE
(FOR 42" DECK MODELS)
2722228 WHEEL-13X5.00-6
(FOR 52" & 61" DECK MODELS)
2
14
4162974.7 WLDMT-CSTR MOUNTING
(FOR 42" DECK MODELS)
4167737.7 WLDMT-CSTR MOUNTING
(USED ON 52" DECKS ONLY)
4167739.7 WLDMT-CSTR MOUNTING
(USED ON 61" DECKS ONLY)
1
15
16
17
64123-16
BLT-HEX 3/8-16X1-1/4
64229-03
LOCKNUT-NYLON 3/8-16
2722230-01 SPANNER-11" WHEEL
(USED ON 42" MODELS)
2722230-03 SPANNER-13" WHEEL
(USED ON 52" & 61" MODELS)
8
8
2
18 64140-9
COTTER PIN
ITM PART NO.
DESCRIPTION
QTY
2
2
2
4
2
2
1
1
2
2
49
KICKPLATE/SEAT ASSEMBLY
FastCat RZ
FIGURE 7
27
15
2
26
4
14
14
36
32
8
13
12
3
6
20
18
21
5
29
19
7
31
9
25
28
23
34
30
22
25
11
8
12
9
12
10
24
17
50
16
1
35
KICKPLATE/SEAT ASSEMBLY
FastCat RZ
FIGURE 7
ITM PART NO.
DESCRIPTION
QTY
1 4167267
S-FRAME W/LABS
2 4163499
SEAT ASSEMBLY
(INCLUDES ITEMS 4,14,15,26,& 27)
*4151800
*4139431
DESCRIPTION
QTY
1
1
KIT-SEAT ADJUSTER
KIT-ARM REST
34167708.7 PLATE-SEAT
4 4124009
SWITCH-SEAT NO
5 64123-64
BLT-HEX 5/16-18X2-1/4
6 33138-09
PIN-CLEVIS GRVD .38 X 1.31
7 64144-30
SNAP RING .375
8 4143354
BUMPER, SEAT MOUNTING
964141-6 NUT-5/16-18
10 2722325
RELAY-40AMP SEALED
11 148082-20 FUSE-20 AMP
12 64197-015 BLT-TDFM 10-32X1/2
132188154 MODULE-DELAY
14 2720975-07 SPACER-NYLON 3/8IN
15 64139-16
BLT-WLF 5/16-18X5/8
16 4164549.2 PLATE-FRONT REMOVABLE
17 64197-005 BLT-TDFM 3/8-16X1-1/4
18 4167134
S-FOOT PLATE
(INCLUDES ITEMS 19-23, 34 & 35)
1
1
4
2
2
4
4
3
2
7
1
16
2
1
2
1
19 4167088
MAT-FOOT PLATE UPPER LH
20 4165931
MAT-FOOT PLATE LOWER
21 64018-2
BLT-CRG 1/4-20 X 3/4
224160281 TUBE-DOCUMENT
2338061A
CAP-VINYL
24 64123-16
BLT-HEX 3/8-16X1-1/4
25 64229-03
NUT-NYL LOCK 3/8-16
26 4155681
ARM REST - RH
27 4155680
ARM REST - LH
28 4164330.7 BRKT-SPRING MOUNTING
294164569 SPRING-SEAT
30 64262-003 BLT-FLG HD 1/4-20X1
31 64229-01
NUT-NYLON LOCK 1/4-20
32 64262-011 BLT-FLG HD 3/8-16X1
33*970393
KIT-SEAT SPRING
(INCLUDES ITEMS 25,28-32)
1
1
2
1
1
2
4
1
1
2
2
4
4
2
1
34 4167087
35 64229-01
36 64163-55
ITM PART NO.
MAT-FOOT PLATE UPPER RH 1
NUT-NYLON LOCK 1/4-20
2
WSHR .328X.75X14 GA
2
* NOT ILLUSTRATED
51
STEERING
FastCat RZ
FIGURE 8
51
1
DETAIL DRAWING
2
31
32
30
7
9
28
10
36
36
52
41
11
11
DETAIL DRAWING
12
39
33
26
38
9
9
25
37
31
25
53
22
53
25
4
34
52
9
6
25
6
24
3
35
50
34
4
49
4
12
15
5
41
7
TO FRAME 46
22
8
47
27
21
34
9
25
34
40
43
45
44
14
18
29
48
16
42
17
13
20
23
52
19
STEERING
FastCat RZ
FIGURE 8
ITM PART NO.
DESCRIPTION
QTY
14165432
2 4165426.7
3 4167093
*4167094
GRIP-HANDLE
LEVER-TRACTION CNTRL
WLDMT-CONTROL BAR, RH
WLDMT-CONTROL BAR, LH
2
2
1
1
4 4167097
4167098
WLDMT-CONTROL BOX RH 1
WLDMT-CONTROL BOX LH 1
5 4167025.7
6 108208
7 64197-015
8 4127142
9 64221-03
10 4143676
114165499
124143571
13 4164024
14 4155661.7
*4155660.7
BRKT-TRACTION LEVER
SWITCH DBL POLE
BLT-TDFM 10-32X1/2 TORX
BSHG-CONTROL ARM
E-RING 19MM/.750
BAR-CONTROL PIVOT
DAMPNER
ROD-CONTROL
ROD-PARKING BRAKE
LINK-PARKING BRAKE RH
LINK-PARKING BRAKE LH
2
2
4
1
6
1
2
2
2
1
1
15 64018-3
164155481
17 64268-03
18 64025-05
194163494
204163493
21 4167267
22 4146988.7
23 64229-01
24 64123-89
254146187
26 64025-33
27 4145106
28 4155483.7
2964168-2
30 64123-69
31 64123-68
32 64151-34
33 64123-105
34 64229-02
354133156
36 64061-25
37 4143595-01
BLT-CRG 3/8-16X1
SPRING-COMPRESSION
LOCKNUT-NYLON 3/8-16
NUT-3/8-16 HEX
TRANSAXLE-RH
TRANSAXLE-LH
S-FRAME W/LABS
BRKT-CNTRL BAR SUPT
LOCKNUT-1/4-20 NYLON
BOLT-HEX 1/4-20X3/4
BEARING-FLANGE
NUT-HEX 5/16-24 LH
SPACER-CONTROL ROD
BRAKE, ARM LINKAGE
COTTER-HAIRPIN
BOLT-5/16-18X1-1/2 HEX
BOLT-HEX 5/16-18X1
NUT-HEX LOCK, 3/8-16 JAM
BLT-HEX 1/4-20X1-5/8
NUT-NYLON LOCK 5/16-18
SPACER
ROLL PIN
ROD END-FEMALE RH
4
2
2
2
ITM PART NO.
38 4143595-02
39 64025-03
40 64144-30
41 64229-02
424147116.7
43 4155482.7
444147196
4541-010
46 64268-01
4764251-002
48 4164075
49 64123-50
504162999
51 4163692
52 64163-07
53 85-SC12
DESCRIPTION
ROD END-FEMALE LH
NUT-HEX 5/16-24
SNAP RING
LOCKNUT-NYLON 5/16-18
LINK-BRAKE
WLDMT-BRAKE ARM
SPACER
SPRING-TENSION
NUT-FL NYLON LOCK 1/4-20
WASHER-M6
WLDMT-ROD PARKING BRAKE
BLT-FLG HD 3/8-16 X 1
SPACER
CAP-TUBE END
WSHR 1-1/32X1-3/4X1/4
SET COLLAR
QTY
2
2
2
4
1
1
1
1
2
2
2
4
2
2
2
2
* NOT ILLUSTRATED
1
1
2
2
6
2
2
1
2
2
2
4
2
4
2
2
2
53
PARKING BRAKE
FastCat RZ
FIGURE 9
54
PARKING BRAKE
FastCat RZ
FIGURE 9
ITM PART NO.
1 4167267
2 4163494
3 64197-015
464168-2
5 4148697
64146187
7 64221-03
82188155
9 4167102.7
1064163-34
1164006-01
12 64123-89
13 2188156
14 4148698.7
152720977
16 64229-01
DESCRIPTION
QTY
S-FRAME W/LABS, TRANSAXLE, RH
BLT-TDFM 10-32X1/2 TORX
COTTER-HAIRPIN.08X1.19
ROD-BYPASS CONTROL
BEARING-FLANGE
E-RING 19MM/.750
GRIP
HANDLE-BRAKE WASHER
LOCKWASHER
BOLT-HEX 1/4-20X3/4
SWITCH-NONO DBL POLE
LINK-DUMP VALVE
SPRING-COMPRESSION
LOCKNUT-1/4-20 NYLON
ITM PART NO.
DESCRIPTION
QTY
1
1
2
2
2
1
1
1
1
1
1
1
1
2
2
2
55
WIRE HARNESS
FastCat RZ
FIGURE 10
1
2
20
2.0 EXP
15
3
11
ELECTRIC
CLUTCH
4
STARTER
GROUND
17
YB
16
B
14 GA
12.0 EXP
5.0 EXP
85
85
30
NC
86
87A
NC
BLADES &
TRACTION
RELAY
B B
86
87A
STARTER
RELAY
12
BR
Y
BR
30
BATTERY
RW
TO ENGINE BLOCK
(GROUND)
BATTERY
W W
87
NO
O O
85
86
87A
NC
DELAY
RELAY
WIRE COLORS
W WHITE
W
YBWB WHITE W/ BLACK STRIPE
G P PURPLE
P O ORANGE
OB ORANGE W/ BLACK STRIPE
PO PURPLE W/ ORANGE STRIPE
OP ORANGE W/ PURPLE STRIPE
DB DARK BLUE
B BLACK
G GREEN
R RED
Y YELLOW
YB YELLOW W/ BLACK STRIPE
RW RED W/ WHITE STRIPE
GY GREEN W/ YELLOW STRIPE
BR BROWN
BRY BROWN W/ YELLOW STRIPE
YB
87
NO
8
BRY
BR
B B
B B
87
NO
8
8
2.0 EXP
14 GA
14 GA
B
16
21
P
R
TO SOLENOID (2)
W
G
(RED)
MAGNETO
STARTER SOL
OIL PRESS
CHARGING
B
DB
SOLENOID
ENGINE
B B
30
6
3
(RED)
(BLACK)
9
16
P P
14 GA
14 GA
7
5.0 EXP
14 GA
14 GA
SWITCH
KEY
Y
OFF
M+G
RUN
B+L
START B+L+S
W W P
O
14 GA
14 GA
B B
BD
R
14 GA
O
O
O
BO
14 GA
7.0 EXP
10
14 GA.
SWITCH
CLUTCH
O
G
HOUR
METER
MAGNETO
6.0 EXP
CARB
SOLENOID
5
B
2.0 EXP
PACKARD
#02962793
VOLTAGE
REGULATOR
P
P
14 GA
14 GA
G
12V
ADAPTER
SWITCH
TRACTION
CONTROL
PO
OB
NO
B
B
NC
13
O O
TO SOLENOID (3) Y
W
B
19
WB
4
O O
2.0 EXP
GY
2.0 EXP
PO
B WB
OP
WB
NO
NC
13
2.0 EXP.
2.0 EXP
SWITCH
TRACTION
CONTROL
BR
W
14
WB
OP
NO
NO
56
SWITCH
BRAKE
SWITCH
SEAT
22
18
TO SOLENOID (1)
14 GA
14 GA
R R
2
ENGINE BLOCK
(GROUND)
14 GA
6.0 EXP
FUSES
7.0 EXP
A B C D E F GY
RW
B
B
BRY
DELAY
MODULE
TO SOLENOID (4)
WIRE HARNESS
FastCat RZ
FIGURE 10
ITM PART NO.
DESCRIPTION
QTY
1 4154880
HARNESS-MAIN WIRE
2 148082-20 FUSE 20 AMP
3 30-419
CABLE-BATT 4 GA BLK 29"
4 4124009
SWITCH-SEAT NO
54165120 METER-HOUR
6 30-180
CABLE-BATT 4 GA RED 29"
7 128010
SWITCH, KEY
8 2722325
RELAY-40AMP SEALED
92188154 MODULE-DELAY
102721505 SWITCH-PTO
114144116 CLUTCH-ELECTRICAL
12 30-184
COVER-POS TERMINAL
13 108208
SWITCH DBL POLE
14 2188156
SWITCH-NONO DBL POLE
1538665
SOLENOID
162308095 COVER-TERMINAL
17 108061-04 CABLE-BATTERY 20 RED
182188225 WIRE-GROUND
192188224 HARNESS-JUMPER
(USED ON KAWASAKI MODELS)
2722013 HARNESS-JUMPER
(USED ON B&S MODELS)
1
2
1
1
1
1
1
3
1
1
1
1
2
1
1
3
1
1
1
20 2720949
21 64141-2
22 4164972
23*56-081-36
1
1
1
1
ASSY-CLUTCH WIRE
NUT-WLF 1/4-20
WIRE-SEAT SWITCH
SLEEVING, ID 0.77 NYLON 2'
ITM PART NO.
DESCRIPTION
QTY
* NOT ILLUSTRATED
57
42" SIDE DISCHARGE
FastCat RZ
FIGURE 11
42
30
42
15
41
27
32
24
25
23
22
43
33
41
40
34
26
36
49
15
28
43
33
34
31
29
35
29
36
38
39
48
50
52
37
53 55
19
56
54
18
7
21
17
51
20
1
20
19
7
4
4
7
46
7
50
4
4
46
8
3
47
45
44
47
2
11
6
5
10
11
12
9
57
12
6
58
58
6
16
13
15
14
TORQUE TO
70 FT-LBS
42" SIDE DISCHARGE
FastCat RZ
FIGURE 11
ITM PART NO.
DESCRIPTION
QTY
1 4167921
S-42 DECK W/LABELS
1
24165244 CHUTE-RUBBER
1
3 4165252.7HINGE-CHUTE_RUBBER 1
4 64123-50
BOLT-HEX 3/8-16X1
5
5 64123-16
BLT-HEX 3/8-16X1-1/4
2
6 64268-03
NUT-FL NYLON LOCK 3/8-165
7 64229-03
LOCKNUT-NYLON 3/8-16
17
8 4165976.7BAFFLE-DISCHARGE
1
9 4167797.7 BAFFLE-FRONT RIGHT
1
10 4167803.7 BAFFLE-FRONT LEFT
1
11 64018-2
BLT-CRG 1/4-20X3/4
4
12 64229-01
LOCKNUT-1/4-20 NYLON
4
13 112111-03 BLADE 21.00 OFFST HLFT 2
14 64123-187 BLT-HEX 5/8-18 X 3 3/4
2
15 64209-03
SPRING WASHER
4
16 4118314
SPACER-BLADE 16MM
2
174152317.7 COVER-BELT
1
184150977.7 COVER-BELT
1
19 64139-08
BOLT-5/16-18X3/4 WLF
4
20 64141-6
NUT-WLF 5/16-18
4
21 64018-23
BLT-CRG 3/8-16X3/4
2
22 4146065
ARM-DECK IDLER ASSY
1
(INCLUDES ITEMS 24-26)
232308133 SPRING
24 64144-40
SNAP RING
254128004 BEARING-BALL
264127999 SEAL
27 64270-01
BOLT-MET HEX M10-1.5X30
28 4128002 END CAP
29 128169
PULLEY-IDLER 5.50
30 64123-90
BOLT-1/2-20X2 HEX
31 64006-05
LOCKWSHR-HELICAL 1/2
3264163-19 WASHER
33 4149197
PULLEY-6.25 DEEP GRVE
34 4165023
S-ASSY SPINDLE OUTER
(INCLUDES ITEMS 35-39)
ITM PART NO.
DESCRIPTION
QTY
354164948 HOUSING-SPINDLE
2
3638348-01 BEARING-SPINDLE
4
37 2183070-02SHAFT-SPINDLE
2
38 64144-38
SNAP RING
2
3938315
NUT-SPINDLE
2
40 64262-012 BLT-FLG HD 3/8-16 X 1-1/4 12
4164163-84 WASHER
4
42 64123-208 BLT-HEX 5/8-18X1.5
2
4364164-12 KEY
2
44 4163749.2 LEADING EDGE-ADJ., RH 1
45 4163750.2 LEADING EDGE-ADJ., LH 1
46 64141-2
NUT-WLF 1/4-20
6
47 64123-114 BLT-HEX 1/4-20X1
6
48 4152578-01SPACER
1
49 64268-05
NUT-FL NYLON LOCK 1/2-131
50 64123-31
BOLT-1/2-13X3 HEX
2
5164144-36 E-CLIP
1
524163332 ROLLER-ANTI-SCALP
1
532721512 ROLLER-5X2.75
1
54 64123-217 BLT-HEX 3/8-16X4-1/4
1
552720685 SPACER-ROLLER
1
56 64141-13
NUT-WLF 1/2-13
1
57 4165871.7 BRKT-BAFFLE MNTG RH
1
58 4167866.7 BRKT-BAFFLE MNTG LH
1
1
1
2
1
1
1
2
1
2
4
2
2
59
52" SIDE DISCHARGE
FastCat RZ
FIGURE 12
23
20
15
14
11
19
16
34
49
25
26
29
17
50
25
27
28
23
32
31
54
13
23
33
14
14
15
11
24
11
49
37
49
13
16
13
18
30
15
18
35
18
61
51
62
9
10
1
9
45
16
62
8
38
53
5
7
3
7
5
51
60
5
7
40
39
6
7
46
47
5
5
44
52
4
36
21
41
57
47
43
46
55
42
55
48
59
22
47
56
12
14
47
46
48
60
2
5
46
48
TORQUE TO
70 FT-LBS
58
52" SIDE DISCHARGE
FastCat RZ
FIGURE 12
ITM PART NO.
DESCRIPTION
QTY
ITM PART NO.
1 4167894
S-52 DECK W/LABELS
2 4143552.2 GUARD-LH 52" DECK
3 4143553.2 GUARD-RH 52" DECK
4 4165244
CHUTE-RUBBER ASSY
5 64123-50
BOLT-HEX 3/8-16X1
6 64018-11
BOLT-CRG 1/2-13X3LG
7 64229-03
LOCKNUT-NYLON 3/8-16
8 64205-029 BLT-MET M12X1.75X40
9 64246-04
NUT-WHIZ M12-1.75
10 2188127
CHAIN-6.35 (.250) 5 LINKS
114144947 PULLEY-SPINDLE
12 112111-02 BLADE 18.00 OFFST HLFT
13 64262-012 BLT-FLG HD 3/8-16 X 1-1/4
14 64209-03
SPRING WASHER.67 ID
15 64164-12
KEY-1/4X1/4X1 SQ END
16 128169
PULLEY, IDLER 5.50
17 4147896
ARM-DECK IDLER ASSY
(INCLUDES ITEMS 30-32)
1
1
1
1
6
2
25
8
16
4
3
3
18
6
3
3
1
18 4165023
S-ASSY SPINDLE OUTER
(INCLUDES ITEMS 25-29)
3
41 4165965.7
42 4165966.7
43 4165967.7
444165976.7
45 64018-23
46 64268-03
47 64018-2
48 64229-01
4964163-84
50 64163-19
51 38524
52 4165252.7
5364144-36
544163514.7
55 4165955.7
56 4165870.7
57 4163438.2
58 4163439.2
59 64141-2
60 64123-114
61 64123-93
62 64141-4
19 64006-05
LOCKWSHR-HELICAL 1/2
20 64123-90
BLT-HEX 1/2-20 X 2
21 4118314
SPACER-BLADE 16MM
22 64123-187 BLT-HEX 5/8-18 X 3 3/4
23 64123-208 BLT-HEX 5/8-18X1.5
242308133 SPRING-EXTENSION
25 38348-01
BEARING-SPINDLE SEALED
26 4164948
HOUSING-SPINDLE 6 HOLE
27 64144-38
SNAP RING
2838315
NUT-SPINDLE
292183070-02SHAFT-SPINDLE
304127999 SEAL
314128004 BEARING
32 64144-40
SNAP RING
33 64270-01
BOLT-MET M10-1.5 X 30
34 4128002
END CAP
354152578-01SPACER
36 64123-16
BLT-HEX 3/8-16X1-1/4
37 64268-05
NUT-FL NY LOCK 1/2-13
38 64018-30
BOLT-CRG 3/8-16 X 4-1/2
392721512 ROLLER
402720685 SPACER-ROLLER
1
1
3
3
3
1
6
3
3
3
3
1
2
1
1
1
2
2
2
3
3
3
DESCRIPTION
BAFFLE-FRONT LH
BAFFLE-FRONT CENTER
BAFFLE-RIGHT FRONT
BAFFLE-DISCHARGE
BOLT-3/8-16X3/4 CARRIAGE
NUT-FL NYLON LOCK 3/8-16
BLT-CRG 1/4-20 X 3/4
LOCKNUT-1/4-20 NYLON
WASHER
WASHER
KNOB-4 PRONG
HINGE-CHUTE RUBBER
E-CLIP
GUIDE-BELT
BRKT-BAFFLE MNTG
BRKT-BAFFLE MNTG RH
EXTENSION-52" CD, RH
EXTENSION-52" CD, LH
NUT-WLF 1/4-20
BLT-HEX 1/4-20X1
BLT-HEX 3/8-16X5
NUT-WLF 3/8-16
QTY
1
1
1
1
2
8
7
7
6
2
2
1
1
1
2
1
1
1
7
7
2
4
61
61" SIDE DISCHARGE
FastCat RZ
FIGURE 13
40
69
22
19
32
18
11
14
70
27
55
41
17
34
57
58
66
25
44
15
28
52
54
11
57
67 36
10
21
24
62
34
60
21
11
33
59
6
73
63
38
34
38
3
74
4
16
7
8
23
30
39
9 13
31
75
74
29
7
56
2
26
7
4
75
20
43
35
65
53
47
45
75
37
47
45
45
61
51
16
50
46
71
64
49
46
48 76
71
48
42
53
53
72
76
40
12
TORQUE TO
70 FT. LBS
47
5
62
69
7
53
61" SIDE DISCHARGE
FastCat RZ
ITM PART NO.
DESCRIPTION
FIGURE 13
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
4167895 S-61" DECK W/ LABELS
4163809.2 BELT COVER RH
4167643.2 BELT COVER LH
38524
KNOB-4 PRONG 3/8-16
4165244 CHUTE-RUBBER ASSY
64158-08 EYE BOLT
64229-03 LOCKNUT NYLON 3/8-16
64123-31 BLT-HEX 1/2-13X3
2721512 ROLLER-5X2.75 CENTERED
548138
BRG NDL.88 1.12 1.00 OPEN END
128169
PULLEY IDLER 5.50
112111-03 BLADE 21.00 OFFST HLFT
2720685SPACER-ROLLER
64262-012 BLT-FLG HD 3/8-16 X 1-1/4
4166593.7 WLDMT-IDLER ARM
64018-21 BLT-CRG 1/2-13 X 4
4163514.7GUIDE-BELT
64006-05 LOCKWSHR-1/2 HELICAL
64123-272 BLT-HEX 1/2-20X2-1/2
4165976.7BAFFLE-DISCHARGE
64268-05 NUT-FL NYLON LOCK 1/2-13
64164-13 KEY 1/4 X 2 SQ
4163332 ROLLER, ANTI-SCALP
4165023 S-ASSYSPNDL ZT200 CNTR
(INCLUDES ITEMS 57-60, & 62)
1
1
1
2
1
1
28
2
5
1
3
3
5
18
1
2
1
1
1
1
2
3
2
3
25
4166686 ASSY-IDLER ARM 1
(INCLUDES ITEMS 10, 15, 28, 41, 55, 66)
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
64141-13 NUT-WLF 3/8-24
64270-02 BOLT-HEX M10-1.5X30 ISOCL10.9
521438
GREASE SEAL 64205-029 BLT-METRIC M12X1.75X40
2188127 CHAIN-6.35 (.250) 5 LINKS
64246-04 NUT-WHIZ M12-1.75
4167735PULLEY-SPINDLE
64018-7 BLT-CRG 3/8-16X1-1/4
4163802-01SPACER-1.0X.516X1-15/16
64123-50 BOLT-HEX 3/8-16X1
64229-02 LOCKNUT-NYLON 5/18
4118314 SPACER-BLADE 16MM
64163-74 WSHR-.516X2X.25THK PLT
64018-30 BLT-CRG 3/8-16 X 4-1/2
64123-108 BLT-HEX 5/8-18X2-1/2
4128004BEARING
4165970.7 BAFFLE-RIGHT FRONT 4
1
1
4
4
8
3
3
2
11
1
3
2
4
3
1
1
ITM PART NO.
DESCRIPTION
QTY
43
64163-55 WSHR .328X.75X14 GA
1
44 4163586SPRING-EXTENSION
1
45
64123-114 BLT-HEX 1/4-20X1
7
46
64018-2 BLT-CRG 1/4-20X3/4
4
47
64141-2 NUT-WLF 1/4-20
7
48
64229-01 LOCKNUT-1/4-20 NYLON
4
49
4165969.7 BAFFLE-FRONT CTR 61
1
50
4165968.7 BAFFLE-FRONT LH
1
51
4163441.2 EXTENSION-61IN, LH 1
52 4163014SPACER
1
53
64268-03 NUT-FL NYLN LOCK 3/8-16 10
54
4163155 INNER RING
1
55
64144-40 SNAP RING
1
56
64018-23 BLT-CRG 3/8-16X3/4 SHRT 2
57
38348-01 BEARING-SPINDLE SEALED 6
58
4164948 HOUSING-SPINDLE 6 HOLE 3
59
64144-38 SNAP RING
3
6038315 NUT-SPINDLE
3
61
4163440.2 EXTENSION-61IN, RH
1
62
2183070-02 SHAFT-SPINDLE LONG
3
63
4165484.7 WLDMT-IDLER PIN 1
64
64123-16 BLT-HEX 3/8-16X1-1/4
2
65
4165252.7 HINGE-CHUTE RUBBER
1
66
85010N
ZERK-1/4-28 STR SLF THRD 1
67
64141-6 NUT-WLF 5/16-18
1
68* 64123-217 BLT-HEX 3/8-16X4 - 1/4
1
(USED ON REAR CENTER ANTI-SCALP ROLLER)
69
64209-03
70
4128002
71
4165978.7
72
4165871.7
73
64123-93
74
64141-4
SPRING WASHER .67 ID
END CAP- 26X7
BRKT-BAFFLE MNTG
BRKT-BAFFLE MNTNG, RH
BLT-HEX 3/8-16 X 5
NUT-WLF 3/8-16
6
4
2
1
2
4
*NOT ILLUSTRATED
63
BELTS-CUTTERDECK
FastCat RZ
FIGURE 14
64
BELTS-CUTTERDECK
FastCat RZ
FIGURE 14
ITM PART NO.
DESCRIPTION
QTY
1 4143733
4163569
BELT-52" CUTTERDECK
BELT-61" CUTTERDECK
1
2 4147716
BELT-42" CUTTERDECK
1
ITM PART NO.
DESCRIPTION
QTY
65
DECALS-POWERUNIT
FastCat RZ
FIGURE 15
5 (UNDER SEAT)
16
9
2
12
6
1
15
8
4
10
13
17
7
11
14
18
66
3
(UNDER FOOTPLATE)
DECALS-POWERUNIT
FastCat RZ
FIGURE 15
ITM PART NO.
1 4165662
2 2000570
34164525
4 4164791
5 2000590
6 4165616
7 4165615
8 4167203
9 4147617
104165610
114164269
12 4167104
13 4167103
14 2000577
15 4167202
164133980
174164406
18 4162916
4162915
4162913
DESCRIPTION
LABEL-CONTROL PANEL
LABEL-WARN FUEL PICT.
LABEL-INFORMATION
LABEL-FASTCAT PRO
LABEL-WARN BATTERY
LABEL-LH TRACTION
LABEL-RH TRACTION
LABEL-PARKING BRAKE
LABEL-FUEL TANK VALVE
LABEL-WARNING
LABEL-DANGER/WARNING
LABEL-HOC INNER
LABEL-HOC OUTER
LABEL, WARNING
LABEL-MANUAL LOCATION
LABEL-MAINTENANCE
LABEL-BOB-CAT
LABEL-DECK SIZE 61"
LABEL-DECK SIZE 52"
LABEL-DECK SIZE 42"
QTY
ITM PART NO.
DESCRIPTION
QTY
1
2
1
1
1
1
1
1
1
1
2
1
1
3
1
1
1
1
67
ACCESSORIES-SUSPENSION SEAT
FastCat RZ
FIGURE 16
7
4
1
6
5
3
2
1
68
ACCESSORIES-SUSPENSION SEAT
FastCat RZ
ITM PART NO.
DESCRIPTION
FIGURE 16
QTY
ITM PART NO.
DESCRIPTION
QTY
1 64141-6
NUT-WLF 5/16-18
8
2 64262-019 BLT-FLG HD 5/16-18 X 1-3/4 2
3 2720975-07 SPACER-NYLON 3/8IN
1
44164679 SEAT-SUSPENSION
1
(ITEMS 1-4 ARE CONTAINED IN KIT 970394)
5
SLIDER-SEAT
2
6
BLT-TORX
4
7 4163499
SEAT ASSEMBLY
1
(ITEMS 5 & 6 ARE INCLUDED ON 4163499)
69
SCHILLER GROUNDS CARE, INC.
ONE BOB-CAT LANE
P.O. BOX 469
JOHNSON CREEK, WI 53038
920-699-2000
www.schillergc.com
©Schiller Grounds Care, Inc. 2010