Maxstar 150 S, STL, And STH

208 580N
Processes
Stick (SMAW) Welding
ENGLISH
OM-2242
2007−12
Arc Welding Power Source
Maxstar 150 S, STL, And STH
With Auto-Linet
And Non-CE Models
File: TIG (GTAW)
Visit our website at
www.MillerWelds.com
ESPAÑOL
Description
FRANÇAIS
TIG (GTAW) Welding
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 2005−04
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Warning Label Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. WEEE Label (For Products Sold Within The EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − SPECIFICATIONS AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3. Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4. Remote 6 Receptacle Information (STL And STH Models Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5. Electrical Service Guide For 230 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7. Selecting A Location, And Connecting Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8. Connecting 1-Phase Input Power For 230 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Front Panel Controls And Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Process Selection (STL Model Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Process Selection (STH Model Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Lift-Arc And TIG Impulse Start Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Set-Up Procedure For The TIG Process And Restoring Factory Default Settings (STH Model Only)
SECTION 5 − MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − PARTS LIST FOR S MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − PARTS LIST FOR STL MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − PARTS LIST FOR STH MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
1
1
1
3
4
4
4
5
5
6
6
7
7
7
8
8
9
10
11
12
12
12
13
13
14
16
16
16
17
18
20
22
24
This information is provided for units with CE certification (see rating label on unit).
Manufacturer:
European Contact:
Miller Electric Mg. Co.
1635 W. Spencer St.
Appleton, WI 54914 USA
Phone: (920) 734-9821
Mr. Danilo Fedolfi,
Managing Director
ITW Welding Products Italy S.r.l.
Via Privata Iseo 6/E
20098 San Giuliano
Milanese, Italy
Phone: 39(02)98290-1
Fax: 39(02)98290203
European Contact Signature:
Declares that this product:
Maxstar 150 S And STH
conforms to the following Directives and Standards:
Directives
Low Voltage Directive: 73/23/EEC
Electromagnetic compatibility Directives: 89/336/EEC, 92/31/EEC
Machinery Directives: 98/37EEC, 91/368/EEC, 92/31/EEC, 133/04, 93/68/EEC
Standards
Arc Welding Equipment − Part 10: Electromagnetic Compatibility (EMC) Requirements.
IEC 60974-10 August 2002
Arc Welding Equipment − Part 1: Welding Power Sources. IEC 60974-1 Ed. 3
Degrees of Protection Provided By Enclosures (IP Code): IEC 60529 Ed. 2.1
Insulation Coordination For Equipment Within Low-Voltage Systems:
Part 1: Principles, Requirements And Tests. IEC 60664-1 Ed. 1.1
The product technical file is maintained by the responsible Business Unit(s) located at the manufacturing facility.
dec_stat_1/07
ENGLISH
Declaration of Conformity for
European Community (CE) Products
som _2007−04
7
Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-5. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
When making input connections, attach proper grounding conductor first − double-check connections.
Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
Turn off all equipment when not in use.
During operation, keep everybody, especially children, away.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
ELECTRIC SHOCK can kill.
If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
Use AC output ONLY if required for the welding process.
If AC output is required, use remote output control if present on
unit.
Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
Wear a safety harness if working above floor level.
Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists in inverter-type
welding power sources after removal of input
power.
Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
HOT PARTS can cause severe burns.
Do not touch hot parts bare handed.
Allow cooling period before working on gun or
torch.
To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
OM-2242 Page 1
ENGLISH
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
If ventilation is poor, wear an approved air-supplied respirator.
Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables,
coatings, cleaners, and degreasers.
Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
Do not use welder to thaw frozen pipes.
Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
Use only correct fuses or circuit breakers. Do not oversize or bypass them.
Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
FLYING METAL or DIRT can injure eyes.
Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
Wear approved safety glasses with side
shields even under your welding helmet.
BUILDUP OF GAS can injure or kill.
Shut off shielding gas supply when not in use.
Always ventilate confined spaces or use
approved air-supplied respirator.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
Wear an approved welding helmet fitted with a proper shade of filter lenses to protect your face and eyes when welding or watching
(see ANSI Z49.1 and Z87.1 listed in Safety Standards).
Wear approved safety glasses with side shields under your
helmet.
MAGNETIC FIELDS can affect Implanted
Medical Devices.
Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
NOISE can damage hearing.
Wear protective clothing made from durable, flame-resistant material (leather, heavy cotton, or wool) and foot protection.
Noise from some processes or equipment can
damage hearing.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
Do not weld where flying sparks can strike flammable material.
Protect yourself and others from flying sparks and hot metal.
Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
Watch for fire, and keep a fire extinguisher nearby.
Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
Do not weld where the atmosphere may contain flammable dust,
gas, or liquid vapors (such as gasoline).
Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
OM-2242 Page 2
Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
Keep cylinders away from any welding or other electrical circuits.
Never drape a welding torch over a gas cylinder.
Never allow a welding electrode to touch any cylinder.
Never weld on a pressurized cylinder − explosion will result.
Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
Turn face away from valve outlet when opening cylinder valve.
Keep protective cap in place over valve except when cylinder is in
use or connected for use.
Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
FIRE OR EXPLOSION hazard.
Do not install or place unit on, over, or near
combustible surfaces.
Do not install unit near flammables.
Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
FALLING UNIT can cause injury.
MOVING PARTS can cause injury.
Keep away from moving parts such as fans.
Keep all doors, panels, covers, and guards
closed and securely in place.
Have only qualified persons remove doors, panels, covers, or
guards for maintenance as necessary.
Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
Use equipment of adequate capacity to lift and
support unit.
If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
READ INSTRUCTIONS.
Read Owner’s Manual before using or servicing unit.
Use only genuine replacement parts from the
manufacturer.
OVERUSE can cause OVERHEATING
H.F. RADIATION can cause interference.
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before
starting to weld again.
Do not block or filter airflow to unit.
FLYING SPARKS can cause injury.
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
Sparks can cause fires — keep flammables away.
STATIC (ESD) can damage PC boards.
Put on grounded wrist strap BEFORE handling
boards or parts.
Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
Keep away from moving parts.
Keep away from pinch points such as drive
rolls.
WELDING WIRE can cause injury.
Do not press gun trigger until instructed to do
so.
Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
OM-2242 Page 3
ENGLISH
1-3. Additional Symbols For Installation, Operation, And Maintenance
1-4. California Proposition 65 Warnings
For Gasoline Engines:
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
For Diesel Engines:
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1, from Global Engineering Documents (phone:
1-877-413-5184, website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, Quincy, MA 02269-9101 (phone:
617-770-3000, website: www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 4221 Walney Road, 5th Floor,
Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 5060 Mississauga,
Ontario, Canada L4W 5NS (phone: 800-463-6727 or in Toronto
416-747-4044, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036–8002 (phone:
212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, Quincy, MA 02269-9101 (phone: 617-770-3000, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 Regional Offices—phone for
Region 5, Chicago, is 312-353-2220, website: www.osha.gov).
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
1. Keep cables close together by twisting or taping them, or using a
cable cover.
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
2. Arrange cables to one side and away from the operator.
To reduce magnetic fields in the workplace, use the following
procedures:
OM-2242 Page 4
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
2-1. Warning Label Definitions
A. Warning! Watch Out! There are possible
hazards as shown by the symbols.
1
Electric shock from welding electrode or
wiring can kill.
1.1 Wear dry insulating gloves. Do not touch
electrode with bare hand. Do not wear wet
or damaged gloves.
1.2 Protect yourself from electric shock by
insulating yourself from work and ground.
1.3 Disconnect input plug or power before
working on machine.
2
Breathing welding fumes can be hazardous
to your health.
2.1 Keep your head out of the fumes.
2.2 Use forced ventilation or local exhaust to
remove the fumes.
2.3 Use ventilating fan to remove fumes.
3 Welding sparks can cause explosion or
fire.
3.1 Keep flammables away from welding. Do
not weld near flammables.
3.2 Welding sparks can cause fires. Have a
A
fire extinguisher nearby, and have a
watchperson ready to use it.
3.3 Do not weld on drums or any closed
containers.
4 Arc rays can burn eyes and injure skin.
4.1 Wear hat and safety glasses. Use ear
protection and button shirt collar. Use
welding helmet with correct shade of filter.
Wear complete body protection.
5 Become trained and read the instructions
before working on the machine or welding.
6 Do not remove or paint over (cover) the
label.
A
A
OM-2242 Page 5
ENGLISH
SECTION 2 − DEFINITIONS
2-2. Symbols And Definitions
A
V
Voltage Input
Volts
Increase/Decrease
Of Quantity
Output
Negative
Positive
Gas Input
High Temperature
Direct Current
Percent
Alternating
Current
I1eff
S
Suitable For Areas
Of Increased
Shock Hazard
Amperes
X
U0
Duty Cycle
Rated No Load
Voltage (Average)
Shielded Metal Arc
Welding (SMAW)
Single Phase Static Frequency
Converter-Transformer-Rectifier
U1
I1max
Primary Voltage
Rated Maximum
Supply Current
Hz
Hertz
Line Connection
U2
I2
Conventional Load
Voltage
Rated Welding
Current
Maximum Effective
Supply Current
Remote
Lift-Arc Start
(GTAW)
Gas Tungsten Arc
Welding (GTAW)
Process
TIG (GTAW) Pulse
HF Impulse Starting (GTAW)
On
Off
Look under unit for
label
2-3. WEEE Label (For Products Sold Within The EU)
Do not discard product (where applicable) with general waste.
Reuse or recycle Waste Electrical
and Electronic Equipment (WEEE)
by disposing at a designated collection facility.
Contact your local recycling office
or your local distributor for further
information.
OM-2242 Page 6
3-1. Specifications
Input Power
Single-Phase
AC
115 Volts Stick
And TIG
15A
115 Volts Stick
20A
115 Volts TIG
20A
Rated Welding
Output
70A @ 22.8 Volts DC,
100% Duty Cycle
Welding
Amperage
Range
20 − 100A
70A @ 22.8 Volts DC,
100% Duty Cycle
20 − 100A
100A @ 24.0 Volts DC,
35% Duty Cycle
100A @ 14.0 Volts DC,
100% Duty Cycle
5 − 150A
150A @ 16.0 Volts DC,
30% Duty Cycle
100A @ 24 Volts DC,
100% Duty Cycle
230 Volts Stick
20 − 150A
150A @ 26.0 Volts DC,
30% Duty Cycle
100A @ 14.0 Volts DC,
100% Duty Cycle
230 Volts TIG
5 − 150A
150A @ 16.0 Volts DC,
30% Duty Cycle
Max
OCV
DC
Amperes Input At Rated
Load Output,
50/60Hz,
Single-Phase
KVA @
Duty
Cycle
KW
17.4
2.0
1.9
17.4
2.0
1.9
26.4
3.0
3.0
18.4
2.1
2.1
Dimensions
Weight
90V
H: 9 in (229 mm)
*12-16
W: 5.5 in (140 mm)
13.7 lb
(6.2 kg)
90V
*12-16
90V
*12-16
28.0
3.4
3.1
13.1
3.0
2.8
21.6
4.9
4.7
8.3
2.0
1.9
14.2
3.2
3.1
L: 13.25 in (337 mm)
90V
*12-16
90V
*12-16
*Sense Voltage For Stick And TIG Lift Arc
3-2. Duty Cycle And Overheating
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
If unit overheats, output stops, the
Overtemperature Light comes On,
and the cooling fan runs. Wait fifteen minutes for unit to cool. Reduce amperage or duty cycle before starting to weld again.
250
OUTPUT AMPERES
200
STICK
(230V)
TIG (115V 20A
& 230V)
NOTICE − Exceeding duty cycle
can damage unit and void warranty.
150
STICK
(115V 20A)
100
50
TIG/STICK
(115V 15A)
0
10
50
100
% DUTY CYCLE
208 608-D
OM-2242 Page 7
ENGLISH
SECTION 3 − SPECIFICATIONS AND INSTALLATION
3-3. Volt-Ampere Curves
Volt-ampere curves show minimum and maximum voltage and amperage output capabilities
of welding power source. Curves of other settings fall between curves shown.
115 VAC Input
230 VAC Input
100
100
80
80
60
TIG/Stick Max
Volts
Volts
60
TIG/Stick Max
40
40
TIG Min
20
TIG Min
20
Stick Min
Stick Min
0
0
0
50
100
Amperes
150
200
0
50
100
Amperes
150
200
208 604-B
3-4. Remote 6 Receptacle Information (STL And STH Models Only)
6
Socket
Socket Information
1
Contactor control +13.8 volts DC.
2
Contact closure to 1 completes contactor control
circuit and enables output when Lift-Arc TIG remote is selected.
3
Output to remote control; +10 volts DC output to
remote control.
4
0 to +10 volts DC input command signal from
remote control.
5
Remote control circuit common.
6
Chassis common.
15 VOLTS DC
OUTPUT
CONTACTOR
REMOTE
OUTPUT
CONTROL
CHASSIS
OM-2242 Page 8
NOTICE − INCORRECT INPUT POWER can damage this welding power source. This welding power source requires a CONTINUOUS supply of
60 Hz (±10%) power at ±10% of rated input voltage. Phase to ground voltage shall not exceed +10% of rated input voltage. Do not use a generator
with automatic idle device (that idles engine when no load is sensed) to supply input power to this welding power source.
Actual input voltage should not exceed ± 10% of indicated required input voltage. If actual input voltage is outside of this range, output may not
be available.
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommendations are for a dedicated branch circuit sized for the rated output and duty cycle of the welding power source.
60 Hz
Single
Phase
Input Voltage
230
Input Amperes At Rated Output
13.1
Max Recommended Standard Fuse Rating In Amperes
Circuit Breaker 1, Time-Delay 2
15
3
20
Normal Operating
Min Input Conductor Size In AWG 4
14
91
(28)
Max Recommended Input Conductor Length In Feet (Meters)
Min Grounding Conductor Size In AWG 4
14
Reference: 2005 National Electrical Code (NEC) (including article 630)
1 Choose a circuit breaker with time-current curves comparable to a Time Delay Fuse.
2 “Time-Delay” fuses are UL class “RK5” .
3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and
above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements.
3-6.
Selecting Extension Cord (Use Shortest Cord Possible)
Conductor Size − AWG [mm2]*
Single Phase AC
Input Voltage
4 [21.2]
6 [13.3]
8 [8.4]
10 [5.3]
12 [3.3]
Maximum Allowable Cord Length in ft (m)
115
160 (49)
107 (33)
71 (22)
47 (14)
29 (9)
230
471 (144)
321 (98)
215 (66)
146 (45)
90 (27)
*Conductor size is based on maximum 3% voltage drop
OM-2242 Page 9
ENGLISH
3-5. Electrical Service Guide For 230 VAC
3-7. Selecting A Location, And Connecting Input Power
1
Welding Power Source
Shoulder Strap
Use strap to lift unit.
!
Do not move or operate
unit where it could tip.
!
Installation must meet all
National and Local Codes
− have only qualified
persons
make
this
installation.
!
Special installation may be
required where gasoline or
volatile liquids are present
− see NEC Article 511 or
CEC Section 20.
1
3
4
5
18 in (460 mm)
The Auto-Line circuitry in this
unit automatically links the
power source to the primary
voltage being applied, either
115 or 230 VAC.
2
Rating Label
Label is located on bottom of unit.
Use rating label to determine
input power needs.
CE model rating labels will
also display the following
symbols: CE, CCC, WEEE,
and IEC 60974-1.
3
6
18 in
(460 mm)
Airflow Distance
Requirements
2
7
NOTICE − Do Not cut off power
cord connector and rewire. The
power cord connector and plugs
will work with standard NEMA receptacles. Modifying power cord,
connector, and plugs will void
product warranty.
For 115 volts ac input power, a 15
or 20 ampere individual branch
circuit protected by time-delay
fuses or circuit breaker is
required. For 230 volts ac input
power, see Section 3-5.
3
4
5
6
7
Power Cord Connector
Plug − NEMA Type 5−15P
Receptacle − NEMA Type
5−15R (Customer Supplied)
Plug − NEMA Type 6−50P
Receptacle − NEMA Type
6−50R (Customer Supplied)
Select plug for power supply
receptacle available at site.
Install plug onto power cord
adapter. As threaded collar is
tightened, push plug onto adapter until collar is completely tight.
Connect plug to receptacle.
Ref. 803 351-D / 237 014-A
OM-2242 Page 10
!
Installation must
meet all
National and Local Codes − have
only qualified persons make this
installation.
!
Disconnect and lockout/tagout
input power before connecting
input conductors from unit.
!
Always connect green or green/
yellow conductor to supply
grounding terminal first, and never
to a line terminal.
1
Black And White Input Conductor
(L1 And L2)
Green Or Green/Yellow Grounding
Conductor
Input Power Cord.
Disconnect Device (switch shown in
the OFF position)
Disconnect Device Grounding
Terminal
Disconnect Device Line Terminals
1
5
=GND/PE Earth Ground
7
4
2
6
L1
L2
2
3
4
1
5
6
Connect green or green/yellow grounding
conductor to disconnect device grounding
terminal first.
3
Connect input conductors L1 and L2 to
disconnect device line terminals.
7
Over-Current Protection
Select type and size of over-current
protection using Section 3-5 (fused
disconnect switch shown).
8
L1
L2
230 VAC, 1
8
Receptacle (NEMA 6-50R)
Customer Supplied
Close and secure door on disconnect
device. Remove lockout/tagout device,
and place switch in the On position.
Tools Needed:
803 766-B / Ref. 802 443-A
OM-2242 Page 11
ENGLISH
3-8. Connecting 1-Phase Input Power For 230 VAC
SECTION 4 − OPERATION
4-1. Front Panel Controls And Gas Connection
1
2
4
3
9
11
12
8
10
6
5
7
Ref. 803 375-A / 233 167-A
1
Ready Light (LED)
Light comes on approximately two seconds after power switch is placed in On (I) position if
Lift-Arc On or Stick has been selected. If TIG
Impulse is selected, ready light comes on only
after output is enabled. The light indicates that
the unit is energized and ready for welding. A
flashing light indicates unit is not ready, or that
there is a functional error.
The
fan motor
controlled.
2
is
thermostatically
High Temperature Light (LED)
Light comes on if unit overheats. Once unit has
cooled down, welding can resume. If this light
flashes, take unit to an Authorized Service
Agent.
3 Amperage Adjustment Control
This control adjusts welding amperage.
4 Process Select Switch
See Section 4-3.
5 Positive Weld Output Receptacle
For Stick welding, connect electrode cable to
this receptacle. For TIG welding, connect work
cable to this receptacle.
6 Negative Weld Output Receptacle
For Stick welding, connect work cable to this
receptacle. For TIG welding, connect torch
cable to this receptacle.
7 Remote Receptacle
For TIG Impulse or Lift-Arc TIG, output may be
adjusted from min to max of the front panel setting with a remote control.
8 Power Switch
Place switch in On (I) or Off (0) position as
needed.
9 Gas Fitting
Fittings have 5/8-18 right-hand threads (3/8-19
BSPP on CE units).
10 Cylinder Valve
Open valve slightly so gas flow blows dirt from
valve. Close valve.
11 Regulator/Flowmeter
12 Flow Adjust
Typical flow rate is 15 cubic feet per hour (7.1
liters per minute) at a maximum of 90 psi (621
kPa).
Connect customer supplied gas hose between
regulator/flowmeter and gas fitting .
4-2. Process Selection (STL Model Only)
1
=Light Off
=Light On
Use control to select required welding
process. Press switch pad until LED
for desired process is illuminated.
2
Lift Arc Start
When selected, a TIG arc starting
method in which the electrode must
come in contact with the workpiece to
initiate an arc is activated (see Section
4-4).
4
2
3
3
Stick (SMAW)
When selected, Adaptive Hot Start
and DIG circuitry are energized.
1
4
Press
OM-2242 Page 12
Process Selector Switch Pad
Press
Press
Lift Arc Start (Remote)
A TIG starting method in which the
electrode must come in contact with
the work and a closure from pin 1 to pin
2 on the remote receptacle (see Section 3-4) is required to initiate an arc.
ENGLISH
4-3. Process Selection (STH Model Only)
1
=Light Off
Process Selector Switch Pad
Use control to select required welding process. Press switch pad until light (LED) for
2
desired process is illuminated.
2
=Light On
=Light Flashing
3
4
TIG Impulse Start
When selected, an impulse HF arc starting
method is activated (see Section 4-4).
3
5
TIG Pulse With TIG Impulse Start
6
When selected, the TIG pulse welding process with impulse HF start is activated.
Pulsing is the alternating raising and lower- 1
ing of the weld output at a specific rate. To
change pulse frequency, see Section 4-5. Press & Release
4
TIG Pulse With Lift-Arc Start
When selected, the TIG pulse welding process with Lift-Arc start is activated (see
Section 4-4).
Press & Release
Press & Release
5 Lift-Arc Start
When selected, a TIG arc starting method
in which the electrode must come in contact
with the workpiece to initiate an arc is activated (see Section 4-4).
6
Press & Release
Press & Release
Stick (SMAW)
When selected, Adaptive Hot Start and
DIG circuitry are energized.
4-4. Lift-Arc And TIG Impulse Start Procedures
Lift-Arc Start
1
2
“Touch”
Workpiece
Open-circuit voltage maybe present
before electrode touches workpiece.
Do NOT Strike Like A Match!
use this method for TIG Impulse starts.
TIG Electrode
2
Touch tungsten electrode to workpiece, hold for 1-2 seconds, slowly
lift electrode, and an arc forms.
1−2
Seconds
Pictorials show Lift-Arc start method − do not
1
TIG Impulse
High frequency starts arc when output
is enabled without making contact with
the workpiece. High frequency turns
off when arc is started.
OM-2242 Page 13
4-5. Set-Up Procedure For The TIG Process And Restoring Factory Default Settings
(STH Model Only)
Set-Up Procedure
3
4
5
6
1
2
3
4
5
6
7
8
Power Switch
Process Switch Pad
Ready Light
High Temp Light
TIG HF Light
TIG Pulse Light
TIG Lift-Arc Light
Stick Light
7
8
2
1
2
To enter Set-Up Mode, turn power On while
pressing and holding the Process switch pad
for approximately 5 seconds, until the Ready
(3) and High Temp (4) lights flash alternately.
Selectable Features:
Feature 1 − Selectable Trigger Method (Three to choose from):
• Standard trigger − Typically used with a remote amperage control device. Standard trigger provides non-contact start in DC Impulse TIG mode. It also enables Lift-Arc start, with a remote control, in Lift- Arc mode.
• Lift-Arc Panel Control − Allows Lift-Arc start without using a
remote control device. Lift-Arc is used when HF starts are not permitted, or to replace scratch starts.
• 2T Trigger Hold − In the HF mode, used with a push button control
device as an on-off switch. In the Lift-Arc mode, using the Lift-Arc
method (see Section 4-4), push and release torch trigger to start
weld. Push and release torch trigger to end weld current and start
Auto Crater. Auto Crater ramps weld current down at a fixed rate
to end the weld cycle.
To change trigger method, enter set-up mode as described above
and illustrated on the next page.
OM-2242 Page 14
Feature 2 − Pulse Frequency: Choose from the following four intervals: .5 PPS, 1 PPS, 2.5 PPS, or 60 PPS.
To change pulse frequency, enter set-up mode as described above
and illustrated on the next page.
Restoring Factory Default Settings
To restore factory default settings, press and hold process switch
pad and turn power On. Ready and high temp lights will begin to flash
alternately. Continue holding process switch pad for approximately
10 seconds until the lights begin to flash simultaneously. Release
switch pad, as factory default settings are restored. The lights will
continue to flash until unit is turned Off. To return to normal welding
operation, turn power On.
Factory default settings:
Trigger Methods for Models with Stock No. 907 136-014 only:
TIG Impulse-standard; Lift-Arc-standard
Trigger Methods: TIG Impulse-Standard; Lift-Arc−On
Pulse Frequency - 2.5 PPS
ENGLISH
Lights Indicate Which Selection Is Active
Light Flashing = Active Feature
Light On = Selected Option Of Feature 1 Or 2
Press & Hold To Scroll Between Features .
Release At Desired Feature.
Feature 1
Trigger Method
Feature 2
Pulse Frequency (PPS)
Press and release switch
pad to see active Trigger Method.
Continue to press and release switch
pad to change Trigger Method.
Press and release switch pad to
see active Pulse Frequency. Continue to press and release switch
pad to change Pulse Frequency.
NOTE: If no action is taken within 5 seconds,
the light for Feature 1 begins to flash, and last
Trigger Method selected remains active.
NOTE:If no action is taken within 5 seconds,
the light for Feature 2 begins to flash, and last
Pulse Frequency selected remains active.
Lift Arc panel
control
2.5 PPS
2T Trigger Hold
60 PPS
.5 PPS
Standard
To save changes and exit
set-up mode, press and
release torch trigger, or
turn power off and wait
until lights turn off, and
then turn power back on.
1 PPS
OM-2242 Page 15
SECTION 5 − MAINTENANCE AND TROUBLESHOOTING
5-1. Routine Maintenance
!
Disconnect power before maintaining.
Maintain more often during severe conditions.
= Check
= Change
= Clean
* To be done by Factory Authorized Service Agent
Δ = Repair
= Replace
Every
3
Months
Labels
Weld Terminals
Gas Hoses
Every
3
Months
Δ Cables And Cords
Every
6
Months
!
Do not remove case when blowing out inside of unit.
Blow out inside. Direct airflow through front and back louvers.
:During heavy service, clean monthly.
5-2. Overload Protection
1
Supplementary Protector CB1
CB1 protects unit from overload. If
CB1 opens, unit shuts down.
Reset supplementary protector.
1
803 375-A
OM-2242 Page 16
ENGLISH
5-3. Troubleshooting
Trouble
No weld output; unit completely inoperative; ready light (LED) Off.
No weld output; ready light (LED) On.
No weld output; high temperature light
(LED) On.
No weld output; high temperature light
(LED) Flashing.
Remedy
Place line disconnect switch in On position.
Check and replace line fuse(s), if necessary, or reset circuit breaker.
Be sure power cord is plugged in and that receptacle is receiving input power.
Check and secure loose weld cable(s) into receptacle(s).
Check and correct poor connection of work clamp to workpiece.
Unit overheated causing thermal shutdown. Allow unit to cool with fan On (see Section 3-2).
Reduce duty cycle or amperage.
Check and correct blocked/poor airflow to unit (see Section 3-7).
Turn Power Off and back On again. If light continues to flash, check with Factory Authorized Service
Agent.
No weld output. Blue light (LED) flashes Line voltage too high or too low. Line voltage must be within ±10%.
continuously, yellow light (LED) off.
Unit needs to reset. Cycle power off and back on. If problem is not corrected, contact Factory Authorized
Service Agent.
No weld output. Blue light (LED) flashes Remote trigger left on. Turn off remote trigger, wait five seconds, and restart operation.
3 times repeatedly, yellow light (LED) off.
No weld output. Blue light (LED) flashes Unit needs to reset. Cycle power off and back on. If problem is not corrected, contact Factory Authorized
4 times repeatedly, yellow light (LED) off. Service Agent.
Erratic or improper welding arc or output.
Use proper size and type of weld cable (see your Distributor).
Clean and tighten weld connections.
Check and reverse polarity; check and correct poor connections to workpiece.
Unit not warmed up enough to require fan cooling.
Check for and remove anything blocking fan movement.
Have Factory Authorized Service Agent check fan motor and control circuitry.
Stick welding problems: Hard starts; Use proper type and size of electrode.
poor welding characteristics; unusual
Check and reverse electrode polarity; check and correct poor connections.
spattering.
Fan not operating.
Make sure a remote control is not connected.
TIG welding problems: Wandering arc; Use proper type and size of tungsten.
hard starts; poor welding characterisUse properly prepared tungsten.
tics; spattering problems.
Check and reverse electrode polarity.
TIG welding problems: Tungsten elec- Shield weld zone from drafts.
trode oxidizing and not remaining bright Check for correct type shielding gas.
after welding.
Check and tighten gas fittings.
Check and change electrode polarity.
OM-2242 Page 17
SECTION 6 − ELECTRICAL DIAGRAM
208 684-E
Figure 6-1. Circuit Diagram For Non CE Model Welding Power Source
OM-2242 Page 18
ENGLISH
219 466-C
Figure 6-2. Circuit Diagram For CE Model Welding Power Source
OM-2242 Page 19
35
36
SECTION 7 − PARTS LIST FOR S MODELS
Hardware is common and
18
20
21
24
2
25
3
26
4
27
28
23
8
1
29
22
5
6
31
30
34
8
7
9
10
15
11
22
16
12
13
33
14
not available unless listed.
803 475-G
Figure 7-1. Parts View
OM-2242 Page 20
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
1
2
3
4
5
5
6
7
8
9
9
10
10
11
12
13
14
15
16
16
18
20
21
22
23
24
25
26
27
27
28
28
29
29
30
31
33
34
35
36
Dia.
Mkgs.
Part
No.
Description
Quantity
. . . PC1 . . 222 765 . . Kit, pcb assy (windtunnel w/cmpnts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PC1 . . 230 210 . . Kit, pcb assy (windtunnel w/cmpnts) (CE ROHS models) . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 701 . . Insulator w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 146 549 . . Fastener, push-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 622 . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 627 . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 674 . . Label, warning (CE modles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 195 666 . . Screw, 010-32x .50 torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 700 . . Wrapper w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 558 . . Term, friction .250 x .032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 178 . . Panel, rear w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 983 . . Panel, rear w/label (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 171 . . Nameplate, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 881 . . Nameplate, rear (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 550 . . Switch, rocker dpst 16A 250 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 536 . . Screw, K50 x 25 rnd washer, hd-trx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 225 180 . . Cable, power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 548 . . Strap, shoulder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . FM . . 208 496 . . Fan w/leads and plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L1, L2, T1 208 538 . . Windtunnel, magnetics w/cmpnt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L1, L2, T1 219 168 . . Windtunnel, magnetics w/cmpnt (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Base w/label, order by serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 561 . . Work Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 596 . . Holder, electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 535 . . Screw, k50 x 12 rnd washer hd-trx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 612 . . Receptacle, twist lock power/gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 229 337 . . Screw, m5-.8 x 12 soc hd -torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 498 . . Receptacle, twist lock power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 174 992 . . Knob, pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Nameplate, front (order by model and serial number) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Nameplate, front (CE models) (order by model and serial number) . . . . . . . . .
. . . . . . . . . . 233 179 . . Panel, front w/nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 170 . . Panel, front w/nameplate (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PC2 . . 212 905 . . Circuit board, operator interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PC2 . . 226 864 . . Circuit board, operator interface (CE ROHS models) . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 556 . . Insulator, heat sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 497 . . Nut, m08-1.2 13 mm hex 8.3 mm t semi cone washer . . . . . . . . . . . . . . . . . . . .
. . . . T3 . . 219 076 . . Core ferrite (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CB1 . . 225 844 . . Supplementary Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 258 . . Adapter, power cable 6−50P (230V/50A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 261 . . Adapter, power cable 5−15P (115V/15A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-2242 Page 21
ENGLISH
Item
No.
SECTION 8 − PARTS LIST FOR STL MODELS
37
38
Hardware is common and
20
22
23
26
30
27
2
3
28
29
4
31
32
25
10
1
33
24
5
6
35
8
8
9
34
36
10
7
11
12
17
13
24
18
14
15
16
not available unless listed.
803 474-J
Figure 8-1. Parts View
OM-2242 Page 22
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
5
6
7
8
9
10
11
12
13
14
15
16
17
18
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Dia.
Mkgs.
Part
No.
Description
Quantity
. . . PC1 . . 222 765 . . Kit, pcb assy (windtunnel w/cmpnts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 701 . . Insulator w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 146 549 . . Fastener, push-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 622 . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 627 . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 674 . . Label, warning (CE modles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 195 666 . . Screw, 010-32x .50 torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 700 . . Wrapper w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 569 . . Hose and clamps (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . GS1 . . 219 967 . . Valve, gas w/fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 558 . . Term, friction .250 x .032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 175 . . Panel, rear w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 170 . . Nameplate, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 550 . . Switch, rocker dpst 16A 250 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 536 . . Screw, K50 x 25 rnd washer, hd-trx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 225 180 . . Cable, power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 548 . . Strap, shoulder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . FM . . 208 496 . . Fan w/leads and plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L1, L2, T1 208 538 . . Windtunnel, magnetics w/cmpnt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Base w/label, order by serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 561 . . Work Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 596 . . Holder, electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 535 . . Screw, k50 x 12 rnd washer hd-trx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 612 . . Receptacle, twist lock power/gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 588 . . Nut, plastic 625-27.81 hex x .14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 229 337 . . Screw, m5-.8 x 12 soc hd -torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 498 . . Receptacle, twist lock power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 589 . . Cover, dust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 174 992 . . Knob, pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Nameplate, front (order by model and serial number) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 177 . . Panel, front w/nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC2, PC3 217 787 . . Circuit board, operator interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 556 . . Insualtor, heat sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 497 . . Nut, m08-1.2 13 mm hex 8.3 mm t semi cone washer . . . . . . . . . . . . . . . . . . . .
. . . CB1 . . 225 844 . . Supplementary Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 258 . . Adapter, power cable 6−50P (230V/50A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 261 . . Adapter, power cable 5−15P (115V/15A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-2242 Page 23
ENGLISH
Item
No.
SECTION 9 − PARTS LIST FOR STH MODELS
40
41
Hardware is common and
19
20
22
24
36
23
26
27
30
2
3
28
4
29
31
32
25
10
1
33
5
8
34
24
6
8
9
35
37
10
7
11
12
17
13
24
18
2
14
15
38
16
not available unless listed.
803 447-J
Figure 9-1. Parts View
OM-2242 Page 24
Item
No.
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
4
5
5
6
7
8
9
9
10
11
11
12
12
13
14
15
16
17
18
18
19
20
22
23
24
25
26
27
28
29
30
31
32
32
33
33
34
34
35
36
38
39
40
41
Dia.
Mkgs.
Part
No.
Description
Quantity
. . . . . . . . . . 208 701 . . Insulator w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 146 549 . . Fastener, push-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 622 . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PC1 . . 222 765 . . Kit, pcb assy (windtunnel w/cmpnts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PC1 . . 230 210 . . Kit, pcb assy (windtunnel w/cmpnts) (CE ROHS models) . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 627 . . Label, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 674 . . Label, warning (CE modles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 195 666 . . Screw, 010-32x .50 torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 700 . . Wrapper w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 569 . . Hose and clamps (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . GS1 . . 219 967 . . Valve, gas w/fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . GS1 . . 208 598 . . Valve, 14 vdc 2way .375−19 thd 2.0mm orf 100psi (CE models) . . . . . . . . . . .
. . . . . . . . . . 208 558 . . Term, friction .250 x .032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 175 . . Panel, rear w/label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 982 . . Panel, rear w/label (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 170 . . Nameplate, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 880 . . Nameplate, rear (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 550 . . Switch, rocker dpst 16A 250 vac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 536 . . Screw, K50 x 25 rnd washer, hd-trx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 225 180 . . Cable, power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 548 . . Strap, shoulder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . FM . . 208 496 . . Fan w/leads and plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L1, L2, T1 208 702 . . Windtunnel, magnetics w/cmpnt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L1, L2, T1 219 169 . . Windtunnel, magnetics w/cmpnt (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 552 . . Insulator, negative stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Base w/label, order by serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 561 . . Work Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 596 . . Holder, electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 535 . . Screw, k50 x 12 rnd washer hd-trx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 612 . . Receptacle, twist lock power/gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 588 . . Nut, plastic 625-27.81 hex x .14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 229 337 . . Screw, m5-.8 x 12 soc hd -torx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 498 . . Receptacle, twist lock power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 589 . . Cover, dust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 174 992 . . Knob, pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . Nameplate, front (order by model and serial number) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 233 176 . . Panel, front w/nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 172 . . Panel, front w/nameplate (CE ROHS models) . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC2, PC3 212 895 . . Circuit board, operator interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC2, PC3 224 535 . . Circuit board, operator interface (CE ROHS models) . . . . . . . . . . . . . . . . . . . . .
. . . PC4 . . 212 890 . . Circuit board, arc starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PC4 . . 228 593 . . Circuit board, arc starter (CE ROHS models) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 556 . . Insualtor, heat sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 208 497 . . Nut, m08-1.2 13 mm hex 8.3 mm t semi cone washer . . . . . . . . . . . . . . . . . . . .
. . . . T3 . . 219 076 . . Core, ferrite (CE models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CB1 . . 225 844 . . Supplementary Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 258 . . Adapter, power cable 6−50P (230V/50A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 219 261 . . Adapter, power cable 5−15P (115V/15A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-2242 Page 25
Notes
Effective January 1, 2007
(Equipment with a serial number preface of “LH” or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions
* Induction Heating Coils and Blankets, Cables, and
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
Non-Electronic Controls
its original retail purchaser that new Miller equipment sold after
* APT & SAF Model Plasma Cutting Torches
the effective date of this limited warranty is free of defects in
* Remote Controls
material and workmanship at the time it is shipped by Miller. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* Accessory (Kits)
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* Replacement Parts (No labor)
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Spoolmate Spoolguns
Within the warranty periods listed below, Miller will repair or
* Canvas Covers
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time
periods. All warranty time periods start on the delivery date of the
equipment to the original end-user purchaser, and not to exceed
one year after the equipment is shipped to a North American
distributor or eighteen months after the equipment is shipped to
an International distributor.
1.
5 Years Parts — 3 Years Labor
2.
3 Years — Parts and Labor
*
*
*
*
*
*
*
*
*
3.
Original main power rectifiers
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Process Controllers
Semi-Automatic and Automatic Wire Feeders
Inverter Power Sources (Unless Otherwise Stated)
Water Coolant Systems (Integrated)
Intellitig
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
1 Year — Parts and Labor Unless Specified
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources, Coolers, and
Electronic
Controls/Recorders
Water Coolant Systems (Non-Integrated)
Flowgauge and Flowmeter Regulators (No Labor)
HF Units
Grids
Spot Welders
Load Banks
Arc Stud Power Sources & Arc Stud Guns
Racks
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Field Options
(NOTE: Field options are covered under True Blue®
for the remaining warranty period of the product they
are installed in, or for a minimum of one year —
whichever is greater.)
Bernard-Branded Mig Guns (No Labor)
Weldcraft-Branded TIG Torches (No Labor)
Subarc Wire Drive Assemblies
4.
6 Months — Batteries
5.
90 Days — Parts
*
MIG Guns/TIG Torches and Subarc (SAW) Guns
Miller’s True Blue® Limited Warranty shall not apply to:
1.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings, relays
or parts that fail due to normal wear. (Exception:
brushes, slip rings, and relays are covered on Bobcat,
Trailblazer, and Legend models.)
2.
Items furnished by Miller, but manufactured by others, such
as engines or trade accessories. These items are covered
by the manufacturer’s warranty, if any.
3.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable and
necessary maintenance, or equipment which has been
used for operation outside of the specifications for the
equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods at
customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED
BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
miller_warr 2007−01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
© 2007 Miller Electric Mfg. Co. 2007−01
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
www.MillerWelds.com