SW-UNM-24FE2GC-24POE User Manual

SW-UNM-24FE2GC-24POE
24-Port 10/100Mbps + 2-Port Gigabit Combo POE
Unmanaged Ethernet Switch
User Manual
Ver 1.1
Chapter 1 Product Introduction
Congratulations on your purchasing of the PoE Ethernet Switch. Before you install and
use this product, please read this manual carefully for full exploiting the functions of this
product.
1.1 Product Overview
The 24FE + 2GE + 2SFP Port PoE Ethernet Switch provides the seamless network
connection. It integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and 10Mbps
Ethernet network capabilities. Its POE ports can automatically detect and supply power
with those IEEE 802.3at compliant Powered Devices (PD). In this situation, the electrical
power is transmitted along with data in one single cable allowing you to expand your
network where there are no power lines or outlets, where you wish to fix devices such as
AP, IP Cameras or IP Phones, etc.
The Switch is easy to install and use. It requires no configuration and installation.
1.2 Features








1-24 port support POE
Supports POE power up to 30W for each POE port
Supports All power up to 370W
Supports POE IEEE 802.3at compliant Powered Devices
Supports IEEE 802.3x flow control for Full-duplex Mode and backpressure for
Half-duplex Mode
8K entry MAC address table with auto-learning and auto-aging
LED indicators for monitoring power, link, activity and speed
Internal power supply
1.3 Package Contents




One 24FE + 2GE + 2SFP Port PoE Ethernet Switch
Four rubber feet, two mounting ears and eights screws
One AC power cord
One User Manual
1
Chapter 2 External Component Description
2.1 Front Panel
The front panel of the Switch consists of series of LED indicators, 24 10/100Mbps
RJ-45 ports, 2 10/100/1000Mbps RJ-45 ports and 2 SFP ports a shown as below.
Figure 1 - Front Panel
10/100Mbps RJ-45 ports (1~24):
Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each has a
corresponding 10/100Mbps LED.
10/100/1000Mbps RJ-45 ports (25T, 26T):
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Each has a corresponding 10/100/1000Mbps LED.
SFP ports (27S, 28S):
Designed to install the SFP module and connect to the device with a bandwidth of
1000Mbps. Each has a corresponding 1000Mbps LED.
LED indicators:
The LED Indicators will allow you to monitor, diagnose and troubleshoot any potential
problem with the switch, connection or attached devices.
Figure 2 - LED Indicators
The following chart shows the LED indicators of the Switch along with explanation of each
indicator.
2
LED
COLOR
Power
Green
LINK/ACT
(1~24)
Green
25,26T
LINK/ACT
Green
27,28S
POE
LINK/ACT
Green
Orange
STATUS
STATUS DESCRIPTION
On
Power On
Off
Power off
On
A device is connected to the port
Off
A device is disconnected to the port
Flashing
Sending or receiving data
On
A device is connected to the port
Off
A device is disconnected to the port
Flashing
Sending or receiving data
On
A device is connected to the port
Off
A device is disconnected to the port
Flashing
Sending or receiving data
On
A Powered Device is connected to the port,
which supply power successfully
Off
No Powered Device connected to the port, or
no power is supplied according to the power
limits of the port.
Flashing
The POE power circuit may be in short or the
power current may be overloaded.
2.2 Rear Panel
The rear panel of the Switch contains AC power connector and one marker shown as
below.
Figure 3 - Rear Panel
AC Power Connector: Power is supplied through an external AC power adapter. It
supports AC 100~240V, 50~60Hz.
3
Chapter 3 Installing and Connecting the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please
read the following topics and perform the procedures in the order being presented.
3.1 Installation
Please follow the following instructions in avoid of incorrect installation causing device
damage and security threat.





Put the Switch on stable place or desktop in case of falling damage.
Make sure the Switch works in the proper AC input range and matches the voltage
labeled on the Switch.
To keep the Switch free from lightning, do not open the Switch’s shell even in power
failure.
Make sure that there is proper heat dissipation from and adequate ventilation around
the Switch.
Make sure the cabinet to enough back up the weight of the Switch and its
accessories.
3.1.1 Desktop Installation
Sometimes users are not equipped with the 19-inch standard cabinet. So when installing
the Switch on a desktop, please attach these cushioning rubber feet provided on the
bottom at each corner of the Switch in case of the external vibration. Allow adequate
space for ventilation between the device and the objects around it.
Figure 4 - Desktop Installation
3.1.2 Rack-mountable Installation in 19-inch Cabinet
The Switch can be mounted in an EIA standard-sized, 19-inch rack, which can be placed
in a wiring closet with other equipment. To install the Switch, please follow these steps:
a.
attach the mounting brackets on the Switch’s side panels (one on each side) and
secure them with the screws provided.
4
Figure 5 - Rack-mountable Installation
b.
use the screws provided with the equipment rack to mount the Switch on the rack and
tighten it.
3.1.3 Power on the Switch
The Switch is powered on by the AC 100-240V 50/60Hz internal high-performance power
supply. Please follow the next tips to connect:
AC Electrical Outlet: It is recommended to use single-phase three-wire receptacle with
neutral outlet or multifunctional computer professional receptacle. Please make sure to
connect the metal ground connector to the grounding source on the outlet.
AC Power Cord Connection: Connect the AC power connector in the back panel of the
Switch to external receptacle with the included power cord, and check the power indicator
is ON or not. When it is ON, it indicates the power connection is OK.
3.2 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing network card driver, please
connect one end of the twisted pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance between Switch and computer is
around 100 meters. Once the connection is OK and the devices are power on normally,
the Link/ACT status indicator lights corresponding ports of the Switch.
3.3 Switch connection to the PD
1-24 ports of the Switch have POE power supply function, the maximum output power up
to 30W each port, it can make PD devices, such as internet phone, network camera,
wireless access point work. You only need to connect the Switch POE port directly
connected to the PD port by network cable.
5
Appendix: Technical Specifications
Standards
IEEE802.3 10Base -T, IEEE802.3u 100Base -TX, IEEE
802.3 1000Base - T, IEEE802.3az, IEEE802.3at,
IEEE802.3af
Network Media (Cable)
10BASE-T: UTP category 5 cable (maximum 100m)
100BASE-TX: UTP category 5,5e cable (maximum 100m)
1000Base-T: UTP category 5, 5e,6 cable (maximum 100m)
Number of Ports
24 x 10/100Mbps Auto-Negotiation ports,2GE+2SFP
LED
indicators
Link/Act
Link/Act
POE
POE
Power
Power
25,26T/
27,28S
Link/Act
Transfer Method
Store-and-Forward
Switching Capacity
12.8G
MAC Address Learning
Automatically learning, automatically Update 8K
Frame Filtering and
Forward Rate
10Mbps: 14880pps
100Mbps: 148800pps
1000Mbps: 1488000pps
Dimensions (L × W × H)
440*208*44 mm
Environment
Operating Temperature: 0 ~40
Storage Temperature: -10 ~70
Operating Humidity: 10%~90% non-condensing
Storage humidity: 5%~90% non-condensing
Power Supply
400W
6
www.morrelltelecom.com
sales@morrelltelecom.com
morrelltelecom
7