®
Range Hood
Tornado Island 48”
User Manual
&
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
Carefully read the important information
regarding installation, safety and maintenance.
Keep these instructions for future reference.
MAAN1448-01
Before You Begin
INSTALLERS - Start Here
Safety Instructions are on pages 4 and 5 and
Installation Instructions are on pages 9 to 15.
Please perform these steps:
1. Read the safety instructions.
2. Read all instructions in the Installation section of
this manual BEFORE installing the range hood.
3. Remove all packing materials.
4. When finished, make sure to leave these instructions with the consumer.
5. Installation is to be done by a qualified technician only. However, the
ultimate responsibility for proper installation falls to the owner.
6. Product failure due to improper installation is not covered under the Warranty.
CONSUMERS - Start Here
Safety Instructions are on pages 4 and 5 and Operating Instructions are
on page 16.
Please perform these steps:
1. Read the safety instructions.
2. Read all instructions in the manual
BEFORE operating the range hood.
3. Remove all packing materials.
4. Installation is to be done by a
qualified technician only. However,
the ultimate responsibility for proper
installation falls to the owner.
5. Product failure due to improper installation is not covered under the Warranty.
Hardware Note: For safety reasons, range hood mounting screws and anchors will not be
included due to the variation of cabinetry constructions and wall material. Please consult your
installation specialist regarding the optimal type of mounting screws and wall anchors to suit your
home’s construction.
—2—
Table of Contents
Before You Begin................................................................................................................................ 2
Table of Contents............................................................................................................................... 3
Important Safety Information............................................................................................................. 4
Included Parts.................................................................................................................................... 6
Range Hood Dimensions................................................................................................................... 7
Specifications..................................................................................................................................... 7
Mounting Bracket............................................................................................................................... 8
Installation.......................................................................................................................................... 9
Step 1 - Read the Safety Instructions............................................................................................. 9
Step 2 - Unpack Range Hood and Prepare Tools........................................................................... 9
Step 3 - Pre-Installation Preparations............................................................................................. 9
Step 4 - Test Unit Functions........................................................................................................... 9
Step 5 - Venting Installation Guidelines........................................................................................ 10
Step 6 - Measuring....................................................................................................................... 12
Step 7 - Installing the hood mounting bracket............................................................................. 12
Step 8 - Venting............................................................................................................................ 13
Step 9 - Electrical.......................................................................................................................... 13
Step 10 - Finishing Installation...................................................................................................... 14
Step 11 - Connect to AC ............................................................................................................. 14
Step 12 - Install Filters ................................................................................................................. 15
Operation......................................................................................................................................... 16
Power Settings.............................................................................................................................. 16
Timer Function.............................................................................................................................. 16
Lights............................................................................................................................................ 16
Maintenance.................................................................................................................................... 16
Cleaning Filters............................................................................................................................. 16
Range Hood Assembly.................................................................................................................... 17
Assembly.......................................................................................................................................... 18
Circuit Diagram............................................................................................................................. 18
Blower Assembly.......................................................................................................................... 18
Electrical Assembly....................................................................................................................... 18
Use and Care Information................................................................................................................ 19
—3—
Important Safety Information
READ ALL INSTRUCTIONS BEFORE USE
Read and follow all instructions before using the range hood to prevent the risk of fire, electric shock,
personal injury, or damage when using the range hood or appliances with the range hood. This guide
does not cover all possible conditions that may occur. Always contact your service technician or
manufacturer about problems that you do not understand.
• The installation in this manual is intended
for qualified installers, service technicians or
persons with a similar qualified background.
Installation must be done by qualified
professionals and in accordance with all
applicable codes and standards, including
fire-rated construction.
• The range hood may have very sharp
edges; please wear protective gloves if it is
necessary to remove any parts for installing,
cleaning or servicing.
• Activating any switch to ON position before
completing installation may cause damage or
electric shock.
• Due to the size of this range hood, a two
person installation is recommended.
To reduce the risk of fire, electric shock, or
injury to persons:
• For general ventilating use only. DO NOT use
to exhaust hazardous or explosive materials
and vapors.
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be
locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
• Clean grease-laden surfaces frequently. To
optimize performance and to disperse air
properly, make sure to vent air outside. DO
NOT vent exhaust into spaces between walls,
crawl spaces, ceilings, attics or garages.
• Ducted fans MUST always be vented to
the outdoors.
• This unit MUST be grounded and used with
metal ductwork only.
• Sufficient air is needed for proper combustion
and exhausting of gases through the duct to
prevent back drafting.
• When cutting or drilling into wall or ceiling, be
careful not to damage electrical wiring or other
hidden utilities.
• All electrical wiring must be properly installed,
insulated and grounded.
• WARNING: To Reduce The Risk Of Fire Or
Electric Shock, Do Not Use This Fan With Any
Solid-State Speed Control Device.
• Old ductwork should be cleaned or replaced
if necessary to avoid the possibility of a
grease fire.
• The combustion air flow needed for safe
operation of fuel-burning equipment may be
affected by this unit’s operation. Follow the
heating equipment manufacturer’s guideline
and safety standards such as those published
by the National Fire Protection Association
(NFPA), and the American Society of Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE), and other local code authorities.
• Check all joints on ductwork to ensure
proper connection; all joints should be
properly taped using a certified aluminum
or foil tape.
• Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the vendor.
READ AND SAVE THESE
INSTRUCTIONS
• Before servicing or cleaning the unit, switch
power off at service panel and lock the service
—4—
Important Safety Information
WARNING: TO REDUCE RISK OF A RANGE
TOP GREASE FIRE:
To reduce the risk of injury to persons in the
event of a gas leaks:
a) Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
low or medium settings.
• Extinguish any open flame.
• DO NOT turn on the lights or any type of appliance.
• Open all doors and windows to disperse the
gas. If you still smell gas, call the gas company
and fire department.
b) Always turn range hood ON when cooking at
high heat or when flambéing food (i.e. Crepes
Suzette, Cherries Jubilee, etc.).
c) Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
Before servicing or cleaning unit, unplug and
disconnect the hood from the power supply.
d) Use proper pan size. Always use cookware
appropriate for the size of the surface element.
Your safety and the safety of others is very
important. We have provided many important
safety messages in this manual and on your
appliance. Always read and obey all safety
messages. All safety messages outline any
potential hazards, how to reduce the chance of
injury, and possible risks if the instructions are not
followed.
WARNING: TO REDUCE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING *
READ AND SAVE THESE
INSTRUCTIONS
a) SMOTHER FLAMES with a close-fitting
lid, cookie sheet, or metal tray, then turn
off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may
be burned.
c) DO NOT USE WATER, including wet dishcloths
or towels - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a Class A, B, C
extinguisher, and you already know how to
operate it.
2) The fire is small and contained in the area
where it is started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips”
published by NFPA
—5—
Included Parts
Ceiling mounting bracket
8 x Mounting Screws
Range Hood
42 x Mounting Screws
8 x Telescopic Ceiling Bracket
12 x Mounting Screws
2 x Filters
Damper
8 x Explode screws
12 x drywall anchors
26 x Nuts
26 x Washers
Lower Chimney
Upper Chimney
`S` mounting hook (1 pcs)
Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to
the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding
the optimal type of mounting screws and wall anchors to suit your home’s construction.
—6—
Range Hood Dimensions
40.5”- 46”
(1030-1170 mm)
11.2”
26” (665 mm)
(285
mm)
10.6”
(270
mm)
6”
(150 mm)
3.5” (90 mm)
16.5”
23.6”
(600
(420
”
24.44
mm)
(570
”
47.24
mm)
mm)
(1200
mm)
Specifications
Body Design
Power Rating
Stainless Steel
120 V / 60 Hz (cETLus Certified)
Total Input Power
410 W
Motor Input Power
400 W
Total Amps
3.4 A
Speed Control Levels
3 Levels
Interference Levels
Motors
Radio Frequency Interference Protected
Single Motor
Control
Electronic Control Panel
Filtration
Illumination
Thin Baffle Filters
4 x 2.5 W LED
Venting Size
Top Round 6 Inches (152 mm)
—7—
Mounting Bracket
—8—
Installation
STEP 1
Read the Safety Instructions
•
It is very important to read the safety instructions on pages 4 and 5.
IMPORTANT: It is the installer’s responsibility to comply with installation clearances.
STEP 2
Unpack Range Hood and Prepare Tools
•
Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6.
•
DO NOT remove the protective film covering the appliance until the installation is fully completed.
•
Consult a qualified and trained installer or check local codes for makeup air requirement, if any.
STEP 3
Pre-Installation Preparations
• Designed for ceiling heights between 8.6 ft. to 9.3 ft. only. Refer to Height and Clearance section.
• Plan a desirable location that fits all requirements in the Safety and Installation sections of this manual. Plan where
and how the ductwork will be installed.
• A straight or short duct run will allow the unit to perform most efficiently. Long duct runs, elbows and transitions
will reduce the performance of the unit. Each elbow is equivalent to 5 to 10 feet of straight run. Proper size duct
work should be 6” (152 mm) in diameter.
• To reach a 9 foot ceiling make sure hood is installed 30 inches from cooking surface.
•
If ductwork is already installed, ensure ductwork is free from debris and measures 6” (152 mm).
•
Install a 120V 60 Hz electrical outlet on the ceiling within the dimensions of the decorative chimney. Note: Removal of
the plug will void the warranty of the range hood.
•
Note that the bottom of the cross-bracing must be level to ensure that the island range hood hangs level.
STEP 4
Test Unit Functions
•
Plug the unit in and test all of the functions before installing.
•
Place the range hood on a flat, stable surface. Connect the range hood to a designated standard outlet (120-Volt, 60Hz,
AC only) and turn on the range hood. Verify all operations of the range hood by referring to Range Hood Operations.
•
Turn power On in control panel.
•
Check all lights and fan operations.
WARNINGS:
• Please make sure to read ALL safety instuctions on pages 4 and 5.
• Use three people to move and install range hood.
• Failure to follow these instructions can result in serious injury.
—9—
Installation
STEP 5
Venting Installation Guidelines
•
The following steps are for exterior ventilation.
•
If you require a ductless installation, please visit anconahome.com to purchase a recirculation kit.
Height and Clearance
Maximum ceiling clearance 114” at 30” hood
mounting height above countertop or stove
(May vary with different model). Chimney
extensions available for higher ceiling
24” (610 mm) Min.
30” (610 mm) Max.
IMPORTANT:
• Vent system must terminate to the outside (roof or side wall).
• DO NOT terminate the vent system in an attic or other
enclosed area.
• DO NOT use 4” (10.2 cm) laundry-type wall caps.
• Use metal/aluminum vent only. A rigid metal/aluminum
vent is recommended.
• DO NOT use a plastic vent.
• Always keep the duct clean to ensure proper airflow.
• Calculate the following figures before installation:
1. Distance from the floor to the ceiling
2. Distance between the floor and the countertop/stove
3. A distance of 24” to 30” is recommended between
stove top and the bottom of range hood. 30” minimum
is required for gas stove tops.
4. Height of hood and duct cover.
For the most efficient & quiet operation:
• It is recommended that the range hood be vented
vertically through the roof through 10” (15.3 cm) or
bigger round metal/aluminum vent work.
• The size of the vent should be uniform.
• Use no more than three 90° elbows.
• Make sure there is a minimum of 24” (61 cm) of
straight vent between the elbows if more than one
elbow is used.
• DO NOT install two elbows together.
• The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
• The vent system must have a damper. If roof or wall
cap has a damper, you may remove damper flaps from
damper to increase air flow.
• Only one flange is needed in the aire duct system,
either on top of the motor or outside.
• Use silver tape or duct tape to seal all joints in the
vent system.
• Use caulking to seal exterior wall or roof opening
around the cap.
— 10 —
Installation
IMPORTANT:
• A minimum of 6” round or 3-1/4 x 10” rectangular duct
(purchased separately) must be used to maintain maximum
airflow efficiency.
• Always use rigid type metal/aluminum ducts if available to
maximize airflow when connecting to provided duct.
• Please use Duct Run Calculation below to compute
total available duct run when using elbows, transitions
and caps.
• ALWAYS, when possible, reduce the number or
transitions and turns. If long duct run is required,
increase duct size from 6” to 7” or 8”. If a reducer
is used, install a long reducer instead of a pancake
reducer. Reducing duct size will restrict airflow and
decrease airflow, thus reduce duct size as far away
from opening as possible.
• If turns or transitions are required, install as far away
from opening and as far apart, between two (2), as
possible.
• Minimum mount height between stove top to hood
bottom should be no less than 24-inch for electric cook
tops and minimum of 30-inch for gas stove tops and
no higher than 30-inch for electric cook tops.
• It is important to install the hood at the proper
mounting height. Hoods mounted too low could
result in heat damage and fire hazard; while hoods
mounted too high may be hard to reach and will lose its
performance and efficiency.
• If available, also refer to stove top manufacturer’s
height clearance requirements and recommended
hood mounting height above range.
• This range hood is factory set for venting through the roof or wall.
• Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.
IMPORTANT:
• NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or
garages. All exhaust must be ducted to the outside.
•
Use metal/aluminum duct work only.
•
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
•
Use caulking to seal exterior wall or roof opening around the cap.
TOP VENTING
ROOF EXHAUST
TOP VENTING
WALL EXHAUST
— 11 —
Installation
STEP 6
Measuring
•
Measure the distance between stove top and the bottom of the range hood. A distance of 24” to 30” is recommended
with a minimum of 30” for gas stove tops.
•
To reach 9ft ceiling make sure hood is installed at 30” from cooking surface.
•
If you require longer chimney flue to reach your ceiling please visit anconahome.com
STEP 7
Installing the Hood Mounting bracket
•
Determine and mark the center line on the ceiling where the range hood will be installed. Make sure there is proper
clearance within the ceiling or wall for exhaust vent.
•
The ceiling must be able to bear at least 40 kg (88 lbs.) of weight, and the thickness of the ceiling must be at least 300
mm (1.8”).
•
Drill 1*170 mm (6.7”) round hole in the ceiling.
•
Run house electrical wires to the electrical box on the bracket. Black to Black, White to White, and Green to Green or
Bare Wires.
•
In line with the hanging board, drill 12 holes in the ceiling. (See Fig. #1)
•
Use supplied screws and nuts to attach the angle iron into the hanging board. (See Fig. #2)
•
Calculate the total length of the angle iron required so that the overlap angle iron is no less than 100 mm (39.4”) and
that the distance from the bottom of the range hood and the cooking surface is between 61 to 76 cm (24” to 30”).
•
Attach the 2 sections of the angle iron together for each corner using provided flat screws and nuts.
Fig #1
Fig #2
— 12 —
Installation
STEP 8
Venting
•
Fix the damper flap into the damper hole on top of the range hood motor box. (See Fig. #3)
•
Let the ducting pipe go inside through the hole from the ceiling. (See Fig. #4)
•
Measure the length of 6`` round metal duct required from the dampler / duct connector to the ductwork rough-in in the
ceiling. Connect the duct to the damper / duct connector and seal with duct tape.
Fig #3
Fig #4
STEP 9
Electrical
•
Use the supplied `S` hook to hold up the chimneys while feeding the electrical wires. (See Fig. #5).
•
Remove the protective coating from the inner chimney. Carefully slide the inner chimney down into the outer chimney.
Slide the chimneys over the angle brackets.
•
Feed the electrical wires up through the chimneys. (See Fig. #6)
•
Connect the electrical wires to the wiring box on the ceiling bracket.
......
......
.....
.....
......
......
Electrical wires
Fig #5
Fig #6
— 13 —
Installation
STEP 10
Finishing Installation
Note: To avoid personal
injury and/or damage to the
range hood, this installation
step requires three people.
•
Slide the inner chimney up to the ceiling and attach it
to the ceiling bracket using the screws. (See Fig. #7)
•
Remove the protective coating from the hood body
and outer chimney.
Ceiling
bracket
Angle Mounting
bracket
Flexible Flue
Inner Flue
Power Cable
Louvers
Metal aire
outlet
Outer flue
Duct Tape
Damper
/ Duct
Connector
Fig #7
STEP 11
Connect to AC
•
Reach in and connect the AC plug into the grounded
AC outlet having 120V, 60Hz.
•
SEE IMPORTANT INSTRUCTIONS ON THE
FOLLOWING PAGE.
3-Pronged Plug
Ground Plug
3-Prong Receptacle
— 14 —
Installation
IMPORTANT:
• Observe all governing codes and ordinances.
• It is the customer’s responsibility to contact a qualified electrical installer.
• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that
the ground path is adequate. A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp
circuit, fused on both sides of the line.
• The range hood must be connected with copper wire/plug only.
• The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible
armored or non-metallic sheathed copper cable. UL/CSA listed strain relief must be provided at each end of the
power supply cable.
• DO NOT ground to a gas pipe.
• Check with a qualified electrician if you are not sure that the range hood is properly grounded.
• DO NOT have a fuse in the neutral or ground circuit.
IMPORTANT: Save this Installation Guide for electrical inspector’s use.
GROUNDING INSTRUCTIONS:
• This appliance must be grounded. In the event of an electrical short-circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current.
• This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged
into an outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk of electric shock.
• Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to
whether the appliance is properly grounded. DO NOT use an extension cord. If the power supply cord is too short,
have a qualified electrician install an outlet near the appliance.
STEP 12
Install Filters
•
Angle the filter into the slots at the back of the hood.
•
Open handle on the filter.
•
Release the handle once the filter fits into a resting
position.
•
Repeat to install the other filter.
•
The baffle filters channel grease released by cooking
foods into the grease trays and prevent flaming foods
on the cook top from damaging the inside of the range
hood. For this reason, the baffle filters must ALWAYS
be installed during range hood use.
•
The baffle filters should be cleaned once a month, or
as needed.
— 15 —
Operation
Increase Decrease Timer
Speed
Speed
Power Settings
Light
Timer Function
Press the button + once and the motor starts to
operate at Low speed.
u
The control module provides the option to run the
motor for a predetermined time period in order to
evacuate remaining vapors from the kitchen.
u
Press the button + again and the motor will reach
Medium speed.
v
Press the timer button while the motor is
running. The motor will shut off automatically after 10
minutes.
v
Press the button + once more and the motor will
reach High speed.
w
Press the button - to lower speeds in succession until
the motor stops working (power off).
x
Lights
Press the light button
off.
u
to turn LED lights on and
Maintenance
Cleaning Filters
IMPORTANT: Drain oil from baffles, spacers, filters, oil tunnels, oil containers before oil and residue overflow!
•
Remove all baffles, spacers, filters, grease tray, and oil containers and discard oil and residue.
•
Wash with warm soapy water. NOTE: Stainless steel baffles, spacers and oil tunnel are top rack dishwasher safe.
•
Dry thoroughly before replacing and follow directions for installation in reverse.
•
Filters should be cleaned after every 30 hours of use.
•
Should filters wear out due to age and prolonged use, replace with a new filter.
— 16 —
Range Hood Assembly
— 17 —
Number
1
2
Part
Mounting plate
Upper chimney
3
Mounting angle
4
Lower chimney
5
Duct tube (not included)
6
PCB box
7
Capacitor
8
Transformer
9
10
Connector
Base of plastic box
11
Air outlet
12
13
Housing
Power cord
14
Grill
15
Blower
16
Wheel
17
Motor
18
Glass
19
Switch box
20
Push button
21
Switch panel
22
Lights
23
Screws
24
Filter
Assembly
Circuit Diagram
Blower Assembly
Number
1
2
Part
Motor
Impeller
3
Blower
Electrical Assembly
Number
1
2
Part
Electrical Box Base
PCB
3
Electrical Cover
4
Capacitor
5
Screw (ST3*10)
6
Screw (ST3*6)
— 18 —
Use and Care Information
Operations
•
Read and understand all instructions and warnings in this manual before operating the appliance. Save these
instructions for future reference.
•
Always leave safety grills and filters in place. Without these components, operating fans could catch on to hair, fingers
and loose clothing.
•
NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans.
•
NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of self
combustion is higher when the oil has been used several times.
•
NEVER cook on “open” flames under the range hood. Check deep-fryers during use; superheated oil may be
flammable.
Cleaning
•
The saturation of greasy residue in the fan and filters may cause increased inflammability. Keep unit clean and free of
grease and residue build-up at all times to prevent possible fires.
•
Filters must be cleaned periodically and free from accumulation of cooking residue (see Cleaning Instructions below).
Old and worn filters must be replaced immediately.
•
DO NOT operate fans when filters are removed. Never disassemble parts to clean without proper instructions.
Disassembly is recommended to be performed by qualified personnel only. Read and understand all instructions and
warnings in this manual before proceeding.
SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!
For optimal operation, clean range hood and all baffle/spacer/filter/grease tray/oil container regularly. Regular care
will help preserve the appearance of the range hood.
Cleaning Exterior Surfaces:
•
Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g. Comet
Power Scrub®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel
surface. For heavier soil use liquid degrease such as “Formula 409®” or “Fantastic®” brand cleaner.
•
If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting
cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. CAUTION: DO NOT
leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently
rub off any stubborn spots. Use dry soft towel to dry the hood.
•
After cleaning, you may use non abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the
stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
•
DO NOT allow deposits to accumulate or remain on the hood.
•
DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
•
DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel
for extended periods. Many of these compounds contain chemicals, which may be harmful.
•
Rinse with water after exposure to these compounds and wipe dry with a clean cloth.
— 19 —
Please register your product warranty by visiting the Ancona Home website.
Canada & USA
Phone: 888-686-0778
Fax: 800-350-8563
Email: service@anconahome.com
Website: www.anconahome.com
Ancona is in association with Mr Appliance for all after sales service calls.
Please contact their service provider or visit their website:
Phone: 888-998-2011
Website: www.mrappliance.com
MAAN1448-01
© 2016 Copyright of Ancona Home. All rights reserved. This material may not be reproduced, displayed, modified or distributed.
— 20 —
Download PDF

advertising