OWNER’S, INSTALLATION
& PARTS MANUAL
V-BOX
GAS AND ELECTRIC
SPREADER UNITS
Sno-Way®, Down Pressure® and EIS® are registered trademarks of Sno-Way International, Inc.
ProControl™, MegaBlade™, V-Wing™, E-Z Switch™, Revolution™, MaxAdjust™, SpeedLock™, and QuickJack™
are trademarks of Sno-Way International, Inc.
©2013 Sno-Way® International
97100701S
TABLE OF CONTENTS
Page
INTRODUCTION ......................................................................................................... 2
SAFETY ...................................................................................................................... 3
GENERAL INFORMATION ......................................................................................... 4
INSTALLATION........................................................................................................... 5
Mounting the Spreader Onto the Vehicle........................................................ 5
Spinner Drive Chain Adjustment..................................................................... 5
Alignment of Spinner Chute Assembly .......................................................... 5
Wiring Harness and Cab Control Installation................................................. 6
Battery Safety.................................................................................................. 12
OPERATION.............................................................................................................. 13
Starting the Engine .........................................................................................
Stopping the Engine .......................................................................................
Clutch Operation.............................................................................................
External Shield Adjustment ...........................................................................
Electric Spreader - On/Off Control Operation ..............................................
Electric Spreader - Dual Variable Control Operation...................................
13
13
13
14
15
16
MAINTENANCE ........................................................................................................ 17
Engine Service and Repair.............................................................................
Electric Throttle Replacement .......................................................................
Dual Electric Controller Error Codes ............................................................
Metri-Pack™ Connector Repair .....................................................................
17
17
18
19
TORQUE SPECIFICATIONS .................................................................................... 21
WIRING SCHEMATIC - GAS SPREADER (Cab Control and Spreader Side)...... 22
ELECTRICAL TROUBLESHOOTING - GAS SPREADER ...................................... 23
WIRING SCHEMATIC - ELECTRIC SPREADER (On/Off Control)......................... 24
WIRING SCHEMATIC - ELECTRIC SPREADER (Dual Variable Control) ............. 25
PARTS LISTS............................................................................................................ 26
CONVEYOR DRIVE AND IDLER...................................................................... 27
MOTOR PLATE & DRIVE - GAS SPREADER ................................................. 29
MOTOR PLATE & DRIVE - ELECTRIC SPREADER ....................................... 31
DUAL MOTOR PLATE & DRIVE - ELECTRIC SPREADER ............................ 33
ELECTRIC THROTTLE..................................................................................... 35
DECAL AND DECAL LOCATION..................................................................... 36
SPREADER BODY ........................................................................................... 37
10" CHUTE/SPINNER ASSEMBLY .................................................................. 39
15" CHUTE/SPINNER ASSEMBLY .................................................................. 41
CAB CONTROL - GAS SPREADER ................................................................ 43
ON/OFF CONTROL - ELECTRIC SPREADER ................................................ 44
DUAL VARIABLE CONTROL - ELECTRIC SPREADER................................. 45
WIRING HARNESS CONNECTORS ................................................................ 46
NUMERICAL INDEX ................................................................................................. 47
DEALER CHECKLISTS ........................................................................ BACK COVER
1
INTRODUCTION
This manual was written for the assembly, installation and
maintenance of your new Sno-Way® V-BOX GAS AND
ELECTRIC SPREADER. Most importantly, this manual
provides an operating plan for safe use. Refer to the Table
of Contents for an outline of this manual.
BE AWARE! It is illegal to remove, deface or otherwise alter the safety decals mounted on this equipment.
Please keep this manual with your machine at all times as
reference material and so it can be passed on to the next
owner if the machine is sold.
Record the Spreader Serial Number and Spreader Model
Number, in the space provided below as a handy record
for quick reference. The Serial Number is located under
the engine cover. This plate contains information that your
Dealer needs, to answer questions, to order replacement
parts, or to complete warranty work, if needed, for your
unit.
We require that you read and understand the contents of
this manual COMPLETELY, especially the chapter on
SAFETY, before attempting any procedure contained in
this manual.
NAME PLATE DATA
SPREADER MODEL NUMBER
SPREADER SERIAL NUMBER
(Located under Engine Cover)
The Society of Automotive Engineers has adopted
this SAFETY ALERT SYMBOL to pinpoint characteristics that, if NOT carefully followed, can create a
safety hazard. When you see this symbol in this manual or on the machine itself, BE ALERT!, your personal safety and the safety of others, is involved.
• Defined in the next column, are the SAFETY ALERT
messages and how they will appear in this manual.
c WARNING
(FILL IN)
DEALER
NAME
ADDRESS
CITY
PHONE (
STATE
ZIP
)–
(FILL IN)
Information, that if not carefully followed, can
cause personal injury or death!
ORIGINAL PURCHASER
NAME
c
CAUTION
Information, that if not carefully followed, can
cause injury or damage to equipment!
ADDRESS
CITY
PHONE (
STATE
ZIP
)–
(FILL IN)
NOTE: Additional information concerning the equipment
or the procedure that may or may not be contained elsewhere in this manual.
We reserve the right to make changes or improve the
design or construction of any part(s) without incurring the
obligation to install such parts or make any changes on
any unit previously delivered.
2
SAFETY
BEFORE ATTEMPTING ANY PROCEDURE IN THIS
BOOK, READ AND UNDERSTAND ALL THE SAFETY
INFORMATION CONTAINED IN THIS SECTION. IN
ADDITION, ENSURE ALL INDIVIDUALS WORKING
WITH YOU ARE ALSO FAMILIAR WITH THESE
SAFETY PRECAUTIONS.
For your safety Warning and Information Decals have
been placed on this product to remind the operator
to take safety precautions. It is important that these
decals are in place and are legible before operation
begins. New decals can be obtained from Sno-Way or
your local dealer.
REMEMBER The careful operator is the best
ALWAYS check surrounding area for hazardous
obstacles before operating this unit.
ALWAYS make sure personnel are clear of area being
spread. Material is discharged from spreader at a high
rate of speed and could injure bystanders.
NEVER leave materials in hopper for long periods of
time. Remember salt is hygroscopic and will attract
enough atmospheric moisture to cause it to “cake”.
NEVER work on the vehicle without having a fully
serviced fire extinguisher available. A 5 lb or larger CO2
or dry chemical unit specified for gasoline, chemical or
electrical fires, is recommended.
operator. Most accidents are caused by human error.
Certain precautions must be observed to prevent the
possibility of injury to operator or bystanders and/or
damage to equipment.
NEVER smoke while working on the vehicle. Gasoline
FIRST TIME OPERATION When running for the first
before operating the spreader.
time or after the unit has not been used for a long period
of time, run and inspect the conveyor system without
spinner and chute assembly attached.
ALWAYS shut off the vehicle and spreader engines,
place the vehicle transmission in “Park”, turn the vehicle
and spreader ignition switches to “OFF” position and
firmly apply the parking brake of the vehicle before
servicing or making any adjustments to the spreader.
NEVER operate spreader when under the influence of
alcohol, drugs or other medications that could hamper
your judgement and reactions. An accident may result in
serious injury or death to other persons or yourself.
ALWAYS operate vehicle in a well-ventilated area. The
and battery acid vapors are extremely flammable and
explosive.
ALWAYS make sure that all safety guards are in place
ALWAYS wait for all movement to stop before servicing
or adjusting the spreader.
NEVER climb on or allow others to climb on the
carbon monoxide in exhaust gas is highly toxic and can
cause injury or death.
spreader.
NEVER wear wrist watches, rings or other jewelry when
for cleaning or adjusting before operating the spreader.
ALWAYS reassemble any parts or hardware removed
working on the vehicle or individual equipment. These
things can catch on moving parts or cause an electrical
short circuit that could result in personal injury.
ALWAYS remove any tools and other materials from the
ALWAYS wear safety goggles when working on the
ALWAYS use auxiliary warning lights, except when
vehicle to protect your eyes from battery acid, gasoline,
and dust or dirt from flying off of moving engine parts.
NEVER allow hands, hair or clothing to get near any
ALWAYS wear safety glasses with side shields when
spreader before operating the spreader
prohibited by law, when operating the spreader.
moving part of the spreader. Never wear neckties or
loose clothing when working on the spreader or the
vehicle.
striking metal against metal! In addition, it is
recommended that a softer (non-chipable) metal material
be used to cushion the blow. Failure to heed could result
in injury to the eye(s) or other parts of the body.
ALWAYS be aware of and avoid contact with hot
surfaces such as engine and exhaust.
NEVER allow children or unauthorized person to
ALWAYS inspect the unit periodically for defects. Parts
operate this spreader.
that are broken, missing or plainly worn must be replaced
immediately. Never operate the unit when in need of
maintenance.
NEVER exceed 45 m.p.h. when loaded spreader is
attached to vehicle. Braking distances may be increased
and handling characteristics may be impaired at speeds
above 45 m.p.h.
ALWAYS lock the vehicle when unattended to prevent
unauthorized operation.
ALWAYS check the job site for terrain hazards,
obstructions and people.
3
REMEMBER it is the owner’s responsibility for
communicating information on the safe use and
proper maintenance of this machine.
GENERAL INFORMATION
c WARNING
WARNING: Check the vehicle’s load rating certification sticker for the maximum vehicle capacity, and DO
NOT overload beyond the vehicle GVWR or GAWR. Overloading could result in an accident, or damage to
the vehicle.
FAILURE TO HEED CAN RESULT IN INJURY OR DEATH.
IMPORTANT: Use of gravel or compactable stone fragments will cause the drive system to jam up. Material
should not be left in the hopper overnight because it to can become rock solid jamming the spreader drive.
Wetted salts when left in a hopper can cause moisture build up on the conveyor chain which can freeze the
chain up solid, jamming the spreader drive. If improper materials or improper handling of materials are fed
through the spreaders the following will result:
1.) Gasoline Engine Spreaders: Gear Box Failure, Broken Chain, Smoking Clutch.
2.) Electric Spreaders: Constant Circuit Breaker Tripping.
These conditions will not be covered under warranty. Failed Gearboxes, Broken Chains, Smoked Clutches
and Burnt Out Electric Motors will not be covered under warranty in such instances
Use the following tables to calculate the vehicle payload whenever you
place material in the spreader
EMPTY
WEIGHT CAPACITY
CONVEYOR BODY SIDE WIDTH HEIGHT OVERALL
(Lbs.)(No
WIDTH
LENGTH (inches) (inches) LENGTH
(inches) Screen or (cubic yd.)
Battery)
RECOMMENDED
USE
10"
5’
39
26
78
468
0.5
SMALL TRUCKS
10"
6’
39
26
91
560
0.75
SMALL TO 1/2 TON TRUCKS
15"
8’
48
27
115
650
1.5
SMALL TO 1/2 TON TRUCKS
15"
8’
48
33
115
760
2.0
FULL SIZE HD TRUCKS
15"
9’
48
33
127
855
3.0
FULL SIZE HD TRUCKS
15"
10’
55
47
139
995
4.0
FULL SIZE HD TRUCKS
Side extensions are not recommended for the S.T. Model Spreader and will void all warranties
MATERIAL WEIGHTS
MATERIAL
LBS. PER CUBIC YD.
LBS. PER CUBIC FT.
# 1 Rock Salt
950
35
# 2 Rock Salt
1,215
45
Coarse Sand - Dry
2,565
95
Coarse Sand - Wet
3,240
120
NOTE: All references to "Left" and "Right" sides relates to equipment as viewed from the rear, and facing the normal
direction of vehicle travel.
IMPORTANT: To help prevent a frozen conveyor chain, empty the spreader when not in use
ABBREVIATION KEY
AR
As Required
CPLG
Coupling
15 Inch Wide
ASSY
Assembly
ELEC
Electric
REQ
15 Inch Wide Series
Spreader
Required
CB
Carriage Bolt
EV
Electric V-Box
SPKT
Sprocket
CHMSL
Center High Mounted
Stop Lights
HV
Honda Powered VBox
SS
Stainless Steel
CONV
Conveyer
I.D.
Inside Diameter
10 Inch Wide
10 Inch Wide Series
Spreader
STD
Standard
SV
V
Small V-Box
Standard Larger
V-Box
ZP
Zinc Plated
4
INSTALLATION
Mounting the Spreader Onto the Vehicle
NOTE: Refer to the Repair Parts Diagrams, which are in
this manual, to help identify parts referenced in the following text.
1. Remove the tailgate from the truck.
2. Lift the spreader by hooking the loop or hole located
on the rear cross channel which is inside the hopper. The
loop or hole is located at the approximate balance point
of the spreader. The balance point may vary with engine
fluid levels, battery, top screen, or any residual material in
the hopper.
c WARNING
Before lifting, check that the hopper is empty of
material. The lifting device must be capable of
supporting the spreader’s weight. See charts for
spreader weights.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
3. Place lengths of lumber under the side ribs of the
spreader. By elevating the spreader off the vehicle, it is
easier to remove excess material that accumulates under
the spreader. Center the spreader on the vehicle with the
end of the rails 14" to the rear of the nearest vertical
obstruction (e.g., bumper, trailer hitch, etc.).
4. Bolt the spreader to the vehicle frame using the holes
located at each lower support leg. Use 1/2" hardware as
required by vehicle application.
5. Using the Tie-down Chains, secure the spreader to
the vehicle using the tabs located at the corners of the
spreader and the vehicle’s factory installed anchor
points.
2. Install the Roller Chain between the Spinner Shaft
Sprocket and the Gear Case Sprocket. Check that the
sprockets are in line. Check the setscrew for tightness.
Install the Master Link.
3. To adjust roller chain tension, loosen the Spinner
Shaft Bearing Bolts and move the Spinner Shaft away
from the Gear Case. Maintain vertical position of the
shaft and alignment of sprockets when tightening bearing
fasteners. After adjusting, correct chain tension should
allow a 5/16” deflection midway between the sprockets.
Additional chain tension may be applied by pulling the
Chute/Spinner Assembly toward the rear. Tighten all
fasteners according to the torque chart on page 21.
4. Install the chain guard using 1/4” x 3/4” long hex cap
screws, lock washers, and nuts.
Alignment of Spinner Chute Assembly
1. Remove Chute Pins from Chute.
2. Lift Chute into place so that the LH Hanger Bracket
aligns with bracket on the spreader frame. Insert long
Chute Pin into left side Chute and spreader brackets.
3. Grease all bearings and especially the hex on the
end of the Spinner Shaft.
4. Swing Chute up and check shaft alignment and Latch
Pin alignment.
5. Loosen RH Hanger Bracket using a 9/16” wrench.
6. Raise the Chute so that 1/4” or less of the hex shaft is
exposed below the coupling. Insert short Chute Pin into
the Spreader Frame and RH Hanger Bracket.
7. Tighten the RH Hanger Bracket.
IMPORTANT: If the Spinner Shaft and Coupler still
do not align correctly after RH Hanger Bracket
adjustment: Adjust the Upper Chute Bearing as
necessary, then repeat steps 4-7. Failure to adjust
properly will result in excessive Coupler and Spinner
Shaft wear. (See Figure 1-1)
NOTE: Check the mounting devices every time the
spreader is placed on the truck and loaded with material
to make sure they are secure.
Spinner Drive Chain Adjustment
Coupler and Spinner
Shaft must be in
alignment to prevent
excessive wear or
damage.
1. Loosely attach the Chute/Spinner Assembly using
four 3/8" x 5/8" bolts, lock washers, and nuts, with the
head of the bolt on the inside of the chute. Push the
Chute/Spinner Assembly toward the front of the vehicle.
Do NOT tighten the bolts.
Figure 1-1
5
Wiring Harness and Cab Control
Installation
On/Off Control (Electric Spreader)
Screw
Relay
REMEMBER After the Spreader is installed on the
vehicle, the Pre-Delivery Check List and Delivery
Check List must be completed.
Circuit
Breaker
Red Wire
Grommet
Tool List
Safety Goggles
12 Volt Test Light
Wire Crimp Tool
Drill
Utility Knife
Drill Bit, 3/8”
Controller
Main Wire
Harness
Metri-Pack
Connector
Terminal
Cable
Tie
Yellow Wire
(terminal attached)
Cab Control (Gas Spreader)
1. Attach the Spreader Harness to the side of the
spreader using pre-drilled holes and number six clamp
loops.
2. Plug the Vehicle Harness into the Spreader Harness.
NOTE: Use Quaker State NYK-77 dielectric grease or
equivalent on all electrical connections.
3. Layout the path for vehicle harness through the rear
window of vehicle. Unplug harness when not in use and
keep in cab until needed.
Fuse
Tap
Figure 1-3
1. Locate the following parts:
• Controller
• Wire Harness, Main
• Circuit Breaker
• Fuse Tap
• Terminal, Female
• Grommet
IGNITION SWITCH
ON/OFF/START
ELECTRIC
CLUTCH SWITCH
LIGHTER HARNESS
• Neoprene Seal
• Red Wire, Short
• Cable Tie, Plastic
• Self Tapping Screw
• Relay, 70A
• Metri-Pack Connector
MAIN HARNESS
(For reference to part numbers, see service parts listing
page 44).
ELECTRIC
THROTTLE SWITCH
Figure 1-2
4. Mount the Cab Control (See Figure 1-2) in a
convenient location. Due to the variety of possible in-cab
locations, Velcro® is provided. A suitable bracket should
be made and fastened to the cab.
NOTE: Take the extra time needed to plan the routing of
the wiring harness before drilling any holes or fastening
the harness or control box in place. Read all the
instructions carefully to ensure all the required conditions
are met for a safe and professional installation.
5. Plug cigarette lighter power lead into power outlet in
vehicle.
6
BATTERY
RELAY
ACCESSORY POWER
(RED)
SPREADER
MOTOR
CAB GROUND
(BLACK)
6. Using a drill, make a 3/8” hole through the vehicle
firewall.
CONTROLLER
CIRCUIT BREAKER
c
CAUTION
Keep wiring harness away from moving parts,
sharp edges and areas of extreme heat to avoid
electrical failure and fire.
Figure 1-4
2. Uncoil the wiring harness and route the end of the
harness with the short red and black wires (with ring
terminals installed) from under the vehicle up into the
engine compartment on the battery side.
3. Position the red and black wires (with terminals) near
the battery and prepare to route the five foot section, with
connector, into the vehicle operator compartment area.
4. Look for an existing hole, with rubber grommet, in the
vehicle firewall. The hole must be 3/8” or larger.
c
CAUTION
DO NOT drill any holes until a thorough visual
inspection is performed to determine that the
area around the hole to be drilled, on both sides
of the firewall, is clear of any obstacles such as
brake lines, linkage or vehicle wiring.
7. Install the grommet into the firewall.
8. Feed the yellow wire (with connector terminal
attached) through the grommet into the cab.
9. Inside the cab, insert the terminal on the yellow wire
into the vacant slot in the back of the three-wire
connector that has red and black wire leads already
installed. Push the terminal fully into the connector until it
locks in place.
c
WARNING
Mount the control box in an area that will not
interfere with the legs during seat travel and
that will not allow the knees to come in contact
with it in an accident.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
5. If an existing 3/8” hole is not available, look for an area
to drill a 3/8” hole that satisfies these conditions;
• Hole should be drilled on the same side of the vehicle
firewall (left or right) as the vehicle battery.
• DO NOT put a hole in such a spot that will force the
wiring harness, when installed, to interfere or be routed
behind accelerator pedal, brake pedal, clutch pedal,
parking brake or associated linkage.
• DO NOT drill any holes until a thorough visual
inspection is performed to determine that the area
around the hole to be drilled, on both sides of the firewall,
is clear of any obstacles such as brake lines, linkage or
vehicle wiring.
NOTE: If the hole has to be drilled through carpeting or
insulation, reverse the direction of the drill until the carpet
has been penetrated, remove the carpet from the hole
saw then use the forward direction to continue drilling
through the firewall, this should prevent “running” in the
carpet.
7
10. Use hook and loop strips (Velcro®) to mount the
control in an appropriate location.
11. Connect the vehicle harness, inside the cab, to the
control box connector.
12. Remove the accessory fuse from the vehicle fuse
box.
Vehicle Fuse
Spade Terminal
Fuse Tap
Figure 1-5
13. Using a test probe, determine the fused “Dead/OFF”
side of the fuse and attach the A.T.O. fuse tap to that side
of the fuse. (See Figure 1-5).
NOTE: Two fuse tap-ins are provided, one for standard
(ATO/ATC) automotive blade fuses and one for miniblade automotive fuses. Determine which type of fuse the
vehicle uses. If the standard fuse is used, the fuse tap-in
will require the provided 1/4” female spade terminal, if the
mini-fuse is used, the fuse tap-in will require the provided
3/16” female spade terminal.
IMPORTANT: DO NOT use fuse designated for head
lamp, tail lamp, stop lights, panel lights, or other
critical fuses.
NOTE: If accessory fuse is not available in the fuse box
use another fuse with a 10-15 amp designation, i.e. radio,
lighter, etc.
Short Red Wire
Breaker
Red Wire
From
Harness
14. Cut end of “Red” wire to length, strip end and install
the appropriate female spade terminal onto wire.
15. Attach female spade terminal to appropriate fuse tapin and re-install fuse.
IMPORTANT: The RED wire must be protected by a
fuse. If it is not practical to attach this wire to a fused
circuit in the vehicle fuse box an in line 10 amp fuse
must be added to this wire.
Figure 1-6
17. Locate short red wire (#96106728) with two ring
terminals. Attach the small ring terminal to the copper
colored post marked BAT on the breaker. Attach the
other, large ring terminal to the battery positive terminal.
(See Figure 1-6).
16. Attach the controller ground wire (black with ring
terminal) to a grounding point inside the vehicle cab.
c
Adaptor
(Purchased)
WARNING
Disconnect vehicle NEG. (-) battery cable while
performing Steps 17-24 to avoid serious bodily
injury from fire or explosion.
Short Red Wire
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
Breaker
Red Wire
From
Harness
Figure 1-7
8
NOTE: If the vehicle has a “side post” battery, it will be
necessary to install adaptors (#96100773) to make
connections at the vehicle battery (See Figure 1-7).
Dual Variable Speed Control (Electric Spreader)
Mounting
Bracket
Cap
Battery Harness
Grommet
IMPORTANT: The circuit breaker must be placed in
a location that will avoid excessive heat. DO NOT
locate these parts near the engine exhaust manifold.
A preferred location is one that will receive good air
flow from the radiator fan, but be protected from
excessive engine heat.
Cable
Tie
Cap
18. Mount the circuit breaker with two (2) #10 x 1" selftapping screws (#98100037).
19. Assemble the relay (from the bag of parts) onto the
relay connector plug on the main wire harness. Mount the
relay, using the mounting tab on the relay and a #10 x 1"
self-tapping screw (#98100037) near the circuit breaker
in a location that will avoid excessive heat.
Vibrator
Light Kit
Controller
Cap
20. Attach the ring terminal of the positive (RED) wire of
the wiring harness to the other terminal of the circuit
breaker.
Main Wire
Harness
21. Attach the black harness negative wire to the vehicle
battery NEG (-) post.
Figure 1-8
c
CAUTION
Keep wiring harness away from moving parts,
sharp edges and areas of extreme heat to avoid
electrical failure and fire.
1. Locate the following parts:
• Controller
• Mounting Bracket
• Wire Harness, Main
• Wire Harness, Battery
• Grommet
22. Route vehicle harness from engine compartment to
rear bumper by the hitch receiver tube. Attach the
harness assembly to the vehicle at different points in the
cab and engine compartment and frame that will not
allow the harness to come in contact with sharp edges,
hot components and moving parts or mechanisms. Be
sure the harness is supported and protected by the
vehicle frame.
23. Fasten the main harness to the rear of the vehicle
near the bumper. Leave enough slack in the harness so
that the motor harness from the spreader can be
connected easily and not be under tension.
24. Connect the motor harness from the spreader to the
main wire harness.
9
• Cable Tie, Plastic
• Vibrator Light Kit
• Cap Covers
(For reference to part numbers, see service parts listing
page 45).
BATTERY
WIRING HARNESS
CONTROLLER
SPREADER
MOTORS
c
CAUTION
Keep wiring harness away from moving parts,
sharp edges and areas of extreme heat to avoid
electrical failure and fire.
VEHICLE
BATTERY
CONTROLLER
POWER LEAD
MAIN WIRING HARNESS
Figure 1-9
NOTE: Take the extra time needed to plan the routing of
the wiring harness before drilling any holes or fastening
the harness or control box in place. Read all the
instructions carefully to ensure all the required conditions
are met for a safe and professional installation.(See
Figure 1-9).
2. Look for an existing hole, with rubber grommet, in the
vehicle firewall. The hole must be 1.0” or larger.
c
CAUTION
DO NOT drill any holes until a thorough visual
inspection is performed to determine that the
area around the hole to be drilled, on both sides
of the firewall, is clear of any obstacles such as
brake lines, linkage or vehicle wiring.
3. If an existing 1.0” hole is not available, look for an area
to drill a 1.0” hole that satisfies these conditions;
• Hole should be drilled on the same side of the vehicle
firewall (left or right) as the vehicle battery.
• DO NOT put a hole in such a spot that will force the
wiring harness, when installed, to interfere or be routed
behind accelerator pedal, brake pedal, clutch pedal,
parking brake or associated linkage.
• DO NOT drill any holes until a thorough visual
inspection is performed to determine that the area
around the hole to be drilled, on both sides of the firewall,
is clear of any obstacles such as brake lines, linkage or
vehicle wiring.
6. Uncoil the battery wiring harness and route the end of
the harness with the short red and black wires (with ring
terminals installed) through the grommet and into the
engine compartment. Position the red and black wires
(with terminals) near the battery.
7. Uncoil the main wiring harness and route from the
vehicle interior, through the grommet, to the rear bumper
by the hitch receiver tube. Attach the harness assembly
to the vehicle at different points in the cab interior, engine
compartment and frame that will not allow the harness to
come in contact with sharp edges, hot components and
moving parts or mechanisms. Be sure the harness is
supported and protected by the vehicle frame.
8. Fasten the main harness to the rear of the vehicle near
the bumper. Leave enough slack in the harness so that
the motor harness from the spreader can be connected
easily and not be under tension.
9. Connect the motor harnesses from the spreader to the
main wire harness.
c
WARNING
Mount the control box in an area that will not
interfere with the legs during seat travel and
that will not allow the knees to come in contact
with it in an accident.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
10. Position the controller mounting bracket in the vehicle
in a suitable location. Using appropriate hardware (not
provided), secure the mounting bracket to the vehicle.
NOTE: If the hole has to be drilled through carpeting or
insulation, reverse the direction of the drill until the carpet
has been penetrated, remove the carpet from the hole
saw then use the forward direction to continue drilling
through the firewall, this should prevent “running” in the
carpet.
4. Using a drill, make a 1.0” hole through the vehicle
firewall.
5. Install the grommet into the firewall.
10
11. Position the controller in the mounting bracket and
secure with two flat washers and cap screws.
• If a standard fuse is used, the fuse tap-in required is
the provided 1/4” female spade terminal (#96002083).
12. Ensure that both power switches on the controller are
in the OFF position.
• If a mini-fuse is used, the fuse tap-in required is the
provided 3/16” female spade terminal (# 96101832).
13. Connect the battery, main wiring harness and vibrator
light kit connectors to the appropriate controller
connectors inside the cab.
16. Attach the appropriate fuse tap (ATC/ATO or Mini
Fuse) to that "Dead/OFF" side of the fuse. (See Figure 110).
14. Route the RED/WHITE wire from the main harness
vibrator light kit connector to the vehicle fuse block.
17. Trim the RED/WHITE wire (from the main harness
vibrator light kit connector) to the length required, and
install a 1/4" Female Blade Connector on the end. Attach
the blade connector to the fuse tap, and insert the fuse in
the fuse box, ensuring the "Dead/OFF" side of the fuse is
properly indexed.
IMPORTANT:
The RED/WHITE wire must be
protected by a fuse. In the steps that follow, this wire
is connected to an existing fuse in the vehicle fuse
box. If it is not practical to attach this wire to an
existing fused circuit in the fuse box, install an in-line
10 amp fuse to this wire before it is connected to
another 12VDC source. The 12VDC source must be a
stand-alone circuit that is powered only when the
ignition is activated. Do not connect it to a vehicle
fan circuit, as voltage may drop below 10VDC during
fan operation and cause the controller to fault.
TOP TERMINAL BATTERY
15. Locate the accessory fuse in the fuse box. Remove
the fuse and using a test probe, determine the “Dead/
OFF” side of the fuse.
NOTE: If an accessory fuse is not available in the fuse
box, use another fuse with a 10-15 amp designation (i.e.
radio, lighter, etc).
Battery Harness
Red Lead
c
WARNING
SIDE TERMINAL BATTERY
Disconnect vehicle NEG. (-) battery cable while
performing the following steps to avoid serious
bodily injury from fire or explosion.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
Side Terminal
Adaptor
(Purchased)
Vehicle Fuse
Spade Terminal
Battery Harness
Red Lead
Fuse Tap
Figure 1-10
NOTE: Two fuse tap-ins are provided, one for standard
(ATO/ATC) automotive blade fuses and one for miniblade automotive fuses. Determine which type of fuse the
vehicle uses.
11
Figure 1-11
18. Attach the ring terminal of the spreader positive
(RED) battery harness wire to the vehicle battery
POSITIVE (+) post (See Figure 1-11).
NOTE: If the vehicle has a side terminal (side post)
battery, it will be necessary to install adaptors
(#96100773) to make connections at the vehicle battery.
19. Connect the vehicle NEG. (-) battery cable to the
battery.
20. Attach the ring terminal of the spreader negative
(BLACK) battery harness wire to the vehicle battery
NEGATIVE (-) post.
Battery Safety
c
WARNING
• Never lay tools or equipment on the battery.
You could accidentally ground the POSITIVE
(+) battery terminal, resulting in electrical
shock, burns or damage to equipment.
• Always disconnect the battery before removing
or replacing electrical components such as the
starter relay or battery cables.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
12
OPERATION
Gas Spreader - Electric Control Operation
• Ensure that fuel shut-off is in "ON" position.
• If engine still fails to start, see engine owner’s manual, shipped with spreader.
Gas Spreaders - Electric Throttle
IGNITION SWITCH
ON/OFF/START
Stopping the Engine
ELECTRIC
CLUTCH SWITCH
Depress the spreader ignition switch to “OFF”.
LIGHTER HARNESS
Clutch Operation
1. Start the engine and adjust the speed to slightly
above idle.
MAIN HARNESS
2. Depress the clutch switch to “ON”.
ELECTRIC
THROTTLE SWITCH
Figure 2-1
NOTE: The conveyor and spinner will operate when the
clutch switch is in the ON or BURST position.
Starting the Engine
Gas Spreaders - Electric Throttle
1. Verify that the clutch switch is “OFF”.
2. Depress the throttle switch to “IDLE” and hold for two
seconds; release.
3. Depress the ignition switch to “START”.
3. Increase the engine speed to the desired RPM.
IMPORTANT:
• To help prevent a frozen conveyor chain, empty
the spreader when not in use.
• If the Conveyor Chain becomes “stuck” or “frozen”, remove the material from the hopper and
free the chain, or move the spreader to a warm
area to thaw the material.
• Do not attempt to free the chain by using a pipe
wrench or any other tool on the output shaft of the
gear case. The gear case is designed to accept
torque from the output shaft only. Attempts to turn
the output shaft will strip the gears and void any
warranty.
• Excessive engine speed, and sudden clutch
engagement, may cause damage to spreader. (See
Figure 2-2).
4. While the engine is cranking, depress the throttle
switch to “Choke/Fast” for 5 seconds, then release
switch. That will ensure that the choke is fully engaged.
This is necessary for cold starting.
5. When the engine starts to fire, tap the "IDLE" side of
the throttle switch once or twice to open choke. This will
allow more air to the carburetor, and the engine will run
smoother.
6. To control engine speed, after starting:
• To increase the engine speed, tap the "CHOKE/
FAST" side of the throttle switch. Be careful not to
engage choke. Warm engine will run rough and
emit black smoke if choke is engaged.
• To decrease the engine speed, tap the "IDLE" side
of the throttle switch.
7. If the engine does not start after 20 seconds of
cranking:
• Depress ignition switch to “OFF” and unplug cigarette adapter.
• Check fuel level.
13
Damage to spreader
can occur if clutch
is engaged at high
engine rpm.
Figure 2-2
The electric clutch can be engaged or disengaged at any
time, and at any engine RPM. However, since
engagement time and thus torque are almost
instantaneous, it is recommended that the electric clutch
be engaged at the lowest possible RPM without stopping
the engine. This will prevent premature spinner chain
failure and chain tension loss.
Shield Adjustment
Spread pattern, and the amount of material dispensed,
depends on engine RPM, gate position, and shield
settings.
• Decreasing RPM, and/or gate-opening, will
decrease the amount of material coming to the spinner.
• Increasing RPM, and/or gate opening, will increase
the amount of material coming to the spinner.
External Shield Configuration
REAR
EXTERNAL
SHIELD
LEFT
EXTERNAL SHIELD
Figure 2-3
External Shield Adjustment
All shields adjusted down
for a confined spread
pattern.
Right shield deflects material
down. Heavy on right side.
Left shield deflects material
down. Heavy on left side.
Figure 2-4
14
Electric Spreader - On/Off Control Operation
c
CAUTION
The controller input voltage must be a minimum
of 11 volts DC for proper operation. Be sure the
vehicle battery and alternator are in good
operating condition and adequate to provide 11
volts DC to the salt spreader controller.
ROCKER SWITCH
(ILLUMINATED IN ON POSITION)
Start:
The ON/OFF switch on the front of the control box is an
illuminating rocker switch. When the ON side of the switch
is depressed, current will be directed to the spinner drive
motor and the indicator light behind the rocker switch will
illuminate to indicate that power is ON to the spinner drive
motor. Also, when the ON switch is depressed, the motor
control will go to FULL.
c
WARNING
Make sure that the vehicle ignition switch is in the
OFF position and key removed from the switch
before inspecting the Spreader for cause of
obstruction.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
If the spinner drive motor stalls, press the OFF side of the
ON/OFF switch to shut off the power to the spinner drive
motor. Turn off the vehicle ignition and remove the key
from the ignition switch. Inspect the hopper and the
spinner drive to determine the cause of the obstruction.
OFF
ON
Correct the problem and test to make sure everything is
clear, then restart the spinner drive motor.
Disconnect Protection:
Figure 2-5
The following control and indicator is located on the face
of the control box (See Figure 2-5):
• Illuminating ON/OFF rocker switch—used to start or
stop spinner motor. Switch is an illuminating, rocker
type switch.
The motor controller controls the speed of the spinner
drive motor by supplying set voltage and current to the
spinner drive motor.
Current is supplied by a control power lead (RED wire)
from the vehicle fuse block and must be protected by a
fuse no greater than 15 amps. This control power lead
must also be connected to the fuse block so that the
controller receives current ONLY when the vehicle
ignition is in the ACC position or RUN position. (See "On/
Off Control (Electric Spreader)" on page 6.)
The spinner drive motor is protected by a 40 amp circuit
breaker installed in the wiring system near the vehicle
battery.
15
The ground wire to the controller circuit must be
connected to a good ground on the vehicle to insure
proper controller function. In case the control ground is
lost, by a disconnected ground wire or poor/improper
ground, the controller will automatically shut down. If the
ON/OFF switch is depressed (ON) and the switch DOES
NOT illuminate, it will indicate an improper ground to the
controller.
Ignition Switch Shutoff Procedures:
If the vehicle ignition switch is turned OFF while the
spreader control is in the ON position, the spinner drive
will shut off. When the vehicle ignition switch is then
turned ON, the spreader control switch must be manually
depressed to the ON position to restart the spinner drive.
MOTOR DUTY CYCLE:
Motor is not a continuous duty cycle motor. If the motor
becomes hot to the touch, the motor is approaching
heat limits. Be sure to allow adequate cooling of motor
before using the spreader again.
Electric Spreader - Dual Variable Control
Operation
c
CAUTION
The controller input voltage must be a minimum
of 11 volts DC for proper operation. Be sure the
vehicle battery and alternator are in good
operating condition and adequate to provide 11
volts DC to the salt spreader controller.
The motor controller controls the speed of the spinner and
conveyor drive motors by supplying a variable voltage and
current to the motors, as determined by their respective
speed control settings.
Current is supplied by a control power lead (RED wire)
from the vehicle fuse block and must be protected by a
fuse no greater than 15 amps. This control power lead
must also be connected to the fuse block so that the
controller receives current ONLY when the vehicle
ignition is in the ACC position or RUN position. (See "Dual
Variable Speed Control (Electric Spreader)" on page 9.)
The spinner and conveyor drive motors are protected by
internal circuit breakers in the controller.
Start
AUGER
SPEED
CONTROL
AUGER
INDICATOR
LIGHT
SPINNER
SPEED
CONTROL
SPINNER
INDICATOR
LIGHT
The POWER switch on the front of the controller is an
illuminating rocker switch. When the ON side of the switch
is depressed, current will be directed to the auger and
spinner drive motors and the indicator light behind the
rocker switch will illuminate to indicate that power is ON.
Adjust the speed of the auger and spinner motors as
desired.
c
WARNING
Make sure that the vehicle ignition switch is in the
OFF position and key removed from the switch
before inspecting the Spreader for cause of
obstruction.
MAIN
POWER
SWITCH
VIBRATOR
SWITCH
(OPTIONAL)
OVERLOAD
INDICATOR
LIGHT
JAM
INDICATOR
LIGHT
Figure 2-6
The following controls and indicators are located on the
face of the controller (See Figure 2-6):
• Illuminating main power rocker switch—used to start
or stop spinner and auger motors (and the optional
vibrator motor if equipped).
• Illuminating vibrator motor rocker switch—used to
start or stop the optional vibrator motor.
• Spinner speed control and indicator light - the dial is
used to adjust the speed of the spinner. The indicator provides dial illumination.
• Auger speed control and indicator light - the dial is
used to adjust the speed of the auger. The indicator
light provides dial illumination.
• Overload indicator light - This light will illuminate
when the auger experiences excessive forces due
to material blockage or freezing.
• Jam indicator light - This light will illuminate when
the auger can no longer turn.
FAILURE TO HEED CAN RESULT IN INJURY
OR DEATH.
If either drive motor stalls, press the OFF side of the ON/
OFF switch to shut off the power to the drive motors. Turn
off the vehicle ignition and remove the key from the
ignition switch. Inspect the hopper and the spinner drives
to determine the cause of the obstruction.
Correct the problem and test to make sure everything is
clear, then restart the drive motors.
Ignition Switch Shutoff Procedures:
If the vehicle ignition switch is turned OFF while the
spreader control power switch is in the ON position, the
spinner and conveyor drive will shut off. When the vehicle
ignition switch is then turned ON, the spreader control
power switch must be manually depressed to the ON
position to restart the spinner drive.
MOTOR DUTY CYCLE:
Motors are not continuous duty cycle motors. If a motor
becomes hot to the touch, the motor is approaching
heat limits. Be sure to allow adequate cooling of motor
before using the spreader again.
16
MAINTENANCE
General
• Use Quaker State NYK-77 dielectric grease,
PN3329 or an equivalent grease, on all electrical
connections at the beginning and end of each season, and as required during the season.
• Grease the idler bearings on the Idler Shaft, flanged
bearings on the Drag Shaft, and spinner shaft bearings every 10 hours of operation.
• Grease the input shaft bearing on the Gear Case
every 50 hours of operation.
NOTE: Over-greasing may cause seal damage. The
Gear Case must be filled to the oil level plug with SAE 90
gear-type lubricant. Keep the breather plug clean.
• Check the Conveyor Chain slack periodically. Check
the tension by measuring the distance between the
end of the rear rail and the point where the chain
contacts the lower flange on the rail. The correct distance for adjustment is 26" to 30". (See Figure 3-1).
• To minimize problems and extend the life of the
Electric Clutch, the following procedures are recommended:
– At the end of each snow season, remove and
clean the clutch.
– After cleaning the clutch, coat both mating
surfaces of the clutch with oil or light grease.
– Remove oil and grease prior to using the clutch
again.
Engine Service and Repair
Maintain the spreader engine according to the engine
owner’s manual which is shipped with the spreader.
Engine warranty is covered by the engine manufacturer
and is described in the back of the engine owner’s
manual.
If service or repair is needed, contact an authorized
Service Center for the manufacturer of your engine. To
serve you promptly, the Service Center will need the
model, type, and code number for your engine. Your
nearest service center is listed in the “Yellow Pages”
under “Engines, Gasoline” or “Gasoline Engines.
Electric Throttle Replacement
Removal
Figure 3-1
• Maintain engine-to-gear case roller chain tension.
Correct chain tension allows 5/16" deflection midway between the sprockets. Oil this chain often, and
at the end of each season.
• Maintain spinner shaft-to-gear case roller tension.
Correct chain tension allows 5/16" deflection midway between the sprockets. To increase chain tension, loosen the bearing mounting hardware and
adjust chain tension with 5/16" adjusting bolts. After
adjusting, re-tighten bearing hardware. Make sure
the Spinner Shaft is vertical and the sprockets are in
line before re-tightening the fasteners. Oil this chain
often, and at the end of the season.
NOTE: Over-tightening the roller chains may damage the
bearings on the Gear Case, the engine, and the Spinner
Shaft. Over-tightening will also shorten the life of the
roller chain and of the sprockets.
• Empty the spreader when it is not in use to prevent
frozen conveyor chain.
• Wash out the spreader when it is not in use. At the
end of the season, oil or paint all bare surfaces after
washing and prior to storing the unit.
17
1. Carefully observe the existing installation. Mark the
bracket position on the Engine Mount.
2. Disconnect the electric wires.
3. Remove 1/4-20 fasteners holding the Electric Throttle
Bracket to the Engine Mount.
4. Remove the 6-32 fasteners holding the Electric
Throttle Motor to the bracket. Remove the motor.
Installation
1. Connect the electric wires matching colors, brown to
brown, red to red.
2. Using the Electric Throttle Control, run the new motor
until the crank reaches the 12 o’clock position. A 9-volt
battery can be a substitute for the control.
3. Fasten the Electric Throttle Motor to the bracket
using the existing hardware.
4. Using the Electric Throttle Control, run the new
Electric Throttle Motor until the Crank is against the
bracket as shown in the parts diagram. (See "ELECTRIC
THROTTLE" on page 35).
5. Place the Electric Throttle Arm on the Crank as
shown in the parts diagram. (See "ELECTRIC
THROTTLE" on page 35.)
6. Place the Electric Throttle Assembly onto the Engine
Mount inserting the Throttle Pin into the engine choke/
throttle linkage plastic slider.
7. Loosely bolt the Electric Throttle Assembly to the
Engine Mount with the existing hardware.
8. Keeping the Electric Throttle Arm parallel to and
against the carburetor, move the Electric Throttle Bracket
forward putting the engine throttle into the full choke
position. Tighten the fasteners according to the torque
chart on page 21.
Dual Electric Controller Error Codes
The controller internal diagnostics will turn an ERROR LED
on and flash a sequence of lights on the FLASH NUMBER
LED when a fault is detected in the system.
Record the number of flashes on the FLASH NUMBER LED,
then refer to the Error Code Chart below to determine the
problem and suggested resolution.
9. Check that the crank is stopped in both directions by
the bracket, not the carburetor linkage.
MAIN
POWER
SWITCH
VIBRATOR
SWITCH
ERROR
INDICATOR
LIGHT
FLASH
NUMBER
LIGHT
Figure 3-2
Controller Error Code Chart
ERROR
LED
FLASH
NUMBER
LED
PROBLEM
RESOLUTION
OFF
OFF
No Problems.
No Errors.
ON
OFF
Motor Overload An electrical overload has occured in either the AUGER or SPINNER
motor. The controller is attempting to eliminate the jam the appropriate
motor and will turn off the ERROR LED if successful.
ON
1 Flash
Low Battery
Voltage
The controller input voltage has been measured at less than 10 volts.
Check the controller input connection and the vehicle battery voltage.
ON
2 Flashes
Blown Fuse
One of the internal controller fuses has failed after power was aplied.
If the AUGER dial light is off, replace the AUGER fuse. If the
SPINNER dial light is off, replace the SPINNER fuse. If, when the
VIBRATOR switch is turned on, the VIBRATOR switch LED is off,
replace the VIBRATOR fuse.
ON
3 Flashes
Disconnected
Motor
Either the AUGER, SPINNER or VIBRATOR motor was disconnected
from the controller when power was first applied. Check the cable
harness or motors for disconnection.
ON
4 Flashes
Overloaded
Spinner Motor
The SPINNER motor is continously drawing greater than 30 Amps of
current, and controller cannot cannot free the jam using 50 Amps of
current. Turn off the controller and physically check that the SPINNER
motor is not jammed.
ON
5 Flashes
Overloaded
Auger Motor
The AUGER motor is continously drawing greater than 52 Amps of
current, and controller cannot cannot free the jam using the AUTOREVERSE feature and 70 Amps of current. Turn off the controller and
physically check that the AUGER motor is not jammed.
Normal state of controller
18
ERROR
LED
FLASH
NUMBER
LED
PROBLEM
RESOLUTION
ON
6 Flashes
External Short
Circuit To
Ground
After power was first applied to the controller, a short circuit to ground
was detected in one of the 12VDC wires leaving the controller. The
short is either in the AUGER WHITE 12VDC wire to ground or the
GREEN SPINNER GREEN 12VDC wire to ground. Turn off the
controller. Disconnect the controller from the motor cable harness then
turn the controller on again. If the ERROR clears, the short is in the
cable harness. If the ERROR does not clear, the controller is at fault
and needs to be replaced.
ON
7 Flashes
Missing Battery The controller input voltage on the RED 10 AWG wire has been
Voltage
measured at less than 5 volts after power was first applied to the
controller. Check the controller input connection for low voltage or for
a poor power connection. The controller does require a minimum of 8
VDC to operate.
Metri-Pack™ Connector Repair
METRI-PACK™ CONNECTOR (TYPICAL)
WIRE
RETAINER
SLEEVE BODY
SHOWN
SLEEVE BODY
(Short)
PIN BODY
(Long)
CONNECTOR
BODY LOCK
TAB
WIRE
RETAINER
Figure 3-4
3. Push wire into connector as far as possible to release
pressure on terminal locking tang.
PIN
CABLE-SEAL
SLEEVE
CABLE-SEAL
4. Locate the terminal lock tang in the connector cavity
by looking into the connector from the mating end. Use
Terminal Removal Tool (#96102499) to depress the lock
tang and gently pull wire to remove wire and terminal
from connector body. (See Figure 3-5).
Figure 3-3
IMPORTANT: Identify wire number/color locations
with connector terminal letters before disassembly.
PIN BODY SHOWN
Terminal Removal
1. Lift connector body lock tab and pull to separate
connector halves.
2. Remove wire retainer on sleeve body or pin body, as
necessary, with a screwdriver and save for re-use (See
Figure 3-4).
Figure 3-5
5. Locate the terminal lock tang in the connector cavity
by looking into the connector from the mating end. Use
Terminal Removal Tool (#96102499) to depress the lock
tang and gently pull wire to remove wire and terminal
from connector body. (See Figure 3-5).
19
Terminal Replacement
1. Cut wire as close as possible to old terminal and
remove old cable seal. (See Figure 3-6).
IMPORTANT: Proper barb location and orientation
for installation of sleeve and pin is shown (See Figure
3-9).
BARB
PIN
SLEEVE
Figure 3-6
IMPORTANT: METRI PACK™ connectors are keyed
A, B, C, etc. for proper contact mating. Be sure
contacts and wire colors/numbers match and are in
proper alignment.
BARB
INSIDE
Figure 3-9
NOTE: Connector bodies are keyed for proper terminal
mating. Be sure terminals are in proper alignment.
6. Push new terminal into connector body until fully
seated (See Figure 3-10).
2. Install new correct size cable seal on wire (See
Figure 3-7).
Cable seals are available for three sizes of wire:
• Large - 1.0 mm (16 gauge) wire
• Medium - 0.8 mm (18 gauge) wire
• Small - 0.5 mm (20 gauge) wire
PIN BODY SHOWN
Figure 3-10
7. Pull on wire slightly to be certain terminal is locked in
place.
8. Install wire retainer.
9. Repeat as necessary to replace other terminals.
Figure 3-7
10. Close connector body (See Figure 3-11).
3. Strip insulation from wire to expose 6mm (1/4 in) and
align cable seal with edge of insulation (See Figure 3-8).
Figure 3-11
Figure 3-8
4. Place appropriate terminal on wire and use Crimper
(#96102500) to secure contact in place with a “W” type
crimp.
5. Use Crimper to secure cable seal to terminal.
20
TORQUE SPECIFICATIONS
5
1 or 2
SAE
Grade
and Head
Markings
8.2
No Marks
5
2
SAE
Grade
and Nut
Markings
8
No Marks
Grade 1
SIZE
8
5.2
5.1
Grade 2
Grade 5, 5.1 or 5.2
Grade 8 or 8.2
Lubricateda
Dryb
Lubricateda
Dryb
Lubricateda
Dryb
Lubricateda
Dryb
lb-ft
lb-ft
lb-ft
lb-ft
lb-ft
lb-ft
lb-ft
lb-ft
21*
27*
32*
43*
45*
60*
10-24
1/4
2.8
3.5
4.5
5.5
7
9
10
12.5
5/16
5.5
7
9
11
15
18
21
26
3/8
10
13
16
20
26
33
36
46
7/16
16
20
26
32
41
52
58
75
1/2
25
31
39
50
63
80
90
115
9/16
36
45
56
70
90
115
130
160
5/8
50
62
78
100
125
160
160
225
Metric Grade 8.8
SIZE
lb-ft
SIZE
lb-ft
M6
7
M12
60
M8
17
M14
95
DO NOT use these values if a different torque value or tightening procedure is given for a specific application.
Fasteners should be replaced with the same or higher grade. If higher grade fasteners are used, these should only be
tightened to the strength of the original.
a
“Lubricated” means coated with a lubricant such as engine oil, or fasteners with phosphate and oil coatings.
b
“Dry” means plain or zinc plated without any lubrication
* Values with asterisk are in lb-in.
21
WIRING SCHEMATIC - GAS SPREADER
(Cab Control and Spreader Side)
FEMALE
TERMINAL
WHITE/BLACK
6
5
7
3
2
1
-
BLACK
6
5
4
3
2
1
YELLOW
HARNESS,
GROUND LEAD
RED
96106025
HARNESS,
CIGARETTE
LIGHTER LEAD
PINK
99100555
CONTROLLER
ASSEMBLY
BLUE
96107113
THROTTLE SWITCH
MOMENTARY/OFF/MOMENTARY
(REMOVE BRIDGE
FOR THIS ASSEMBLY)
96102480
96105926
CLUTCH SWITCH
START/ON/OFF SWITCH
(ON/OFF/MOMENTARY)
(ON/ON/OFF)
CAB CONTROL
RED/BLACK
6
5
3
2
4
1
MALE
TERMINAL
YELLOW
BROWN
GREEN
2
5 3
1
2
4 5
1
3
HARNESS,
POWER
96108645
HARNESS,
MAIN SECTION
96109135
CONNECTOR REPAIR KIT
(See parts pages for detail)
JUMPER
FEMALE TERMINAL
(GREEN)
CONNECT TO GROUND
LEAD (WHITE/BLACK)
MICRO-RELAY
(In Kit)
BLUE
STARTER MOTOR
+
FROM
GROUND
BATTERY
GREEN
GROUND
BLACK
BLACK
RED
WHITE/BLUE
MICRO-RELAY (In Kit)
(NO/NC)
GROUND
M
96108646
HARNESS,
SPREADER
JUMPER,
POWER ON
SOLENOID
SWITCH
SPREADER SIDE
YELLOW
BROWN
GREEN
ORANGE
BLACK
RED
BLUE
GREEN
BROWN
POINTS (ENGINE)
RED
M
THROTTLE MOTOR
BROWN
YELLOW
ELECTRIC CLUTCH
96109135
CONNECTOR REPAIR KIT
(See parts pages for detail)
GROUND
22
ELECTRICAL TROUBLESHOOTING - GAS SPREADER
ON/OFF/START THROTTLE
SWITCH SWITCH
CONNECTOR
PIN LOCATIONS
5
4
3
2
1
10 9
8
7
6
CLUTCH
SWITCH
MAIN HARNESS
FUNCTION
SWITCH
NAME
ACTIVATED
WIRE COLOR
SWITCH ON
Starting Motor
On/Off/Start
Blue
Starter Motor
Controller On
On/Off/Start Orange (+12V)
Controller Off/Engine Off
On/Off/Start
Black
(Grounded)
OFF
-
-
MAIN
RELAY #1
Power to
Control
Power Off to
Control
Clutch On
Clutch
Yellow (+12V)
Clutch Momentary On
Clutch
Yellow (+12V)
Clutch Off
Clutch
Yellow (OC)
Throttle Up/Choke
Throttle
Brown (+12V)
Red (-12V)
Neutral Throttle
Throttle
Brown and
Red (OC)
Minimum Throttle
Throttle
Red (+12V)
Brown (-12V)
Cig. Lighter Unplugged
MIDDLE
On
Momentary
Off
On
Off
On
Black
(Grounded)
ENGINE CUT
OFF RELAY
#2 NO/NC
CIG.
ADAPTER
PIN #
On
On
On
3
On
On
On
OC
Off
Off
On
1, 6
On
On
On
4
On
On
On
4
On
On
On
OC
On
On
On
(+) 5, (-) 2
On
On
On
OC
On
On
On
(+) 2, (-) 5
Off
Off
Pulled Out
1, 6
Activates Light on Switch
Pink (+12V)
NA
Controller Ground Through
Cig. Lighter
White/Black
NA
Ground Harness
Green
6
SPREADER HARNESS
ACTIVATED WIRE COLOR
PIN #
FUNCTION
Black
1
Points (Join 1 & 6, engine stops: points grounded)
Red
2
Activates Throttle Motor to Rev Engine Down
Blue
3
Activates Starter Solenoid to Start Engine
Yellow
4
Activates Clutch
Brown
5
Activates Throttle Motor to Rev Motor Up all the Way to Choke
Green
6
Ground on Spreader
CIRCUIT CHECK CHART (Cigarette Lighter plugged in and has power)
COLOR
PIN #
MAIN SWITCH
ON
MAIN SWITCH
OFF
THROTTLE UP
THROTTLE
DOWN
ENGINE START
CLUTCH ON
Black
Red
1
OC
1 & 6 Joined
OC
OC
OC
OC
2
OC
OC
-
+
OC
OC
Blue
3
OC
OC
OC
OC
+
OC
Yellow
4
OC
OC
OC
OC
OC
+
Brown
5
OC
OC
+
-
OC
OC
Green (Ground)
6
NA
NA
NA
NA
NA
NA
NOTE: OC= Open Circuit , + = +12V, - = - 12V. Check with Black lead on tester to Green (ground), Red lead on tester to termination point of wire.
23
WIRING SCHEMATIC - ELECTRIC SPREADER
(On/Off Control)
NOTE: SEE PAGE 32
FOR SERVICE PARTS
DETAIL
MOTOR DUTY CYCLE:
Motor is not a continuous duty cycle motor.
If the motor becomes hot to the touch, the
motor is approaching heat limits.
Be sure to allow adequate cooling of motor
before using the spreader again.
RED
BLACK
12V DC
ELECTRIC
MOTOR
A
B
B
BLACK
U
A
RED
VEHICLE GROUND
BLACK
40A Circuit
Breaker
VEHICLE
BATTERY
2RED
BLACK
YELLOW
BLACK
GROUND
CIRCUIT BREAKER NOTE:
The 40 amp circuit breaker is designed to
trip when motor is in a dead short or
overload (ie jammed). This breaker
WILL NOT protect against thermal overload,
or running the motor outside of its duty cycle.
TO VEHICLE
RED
IGNITION
SWITCH “RUN”
OR “ACCESSORY”
FUSED TERMINAL A B C
ILLUMINATING
ON/OFF ROCKER SWITCH
YELLOW
BROWN
WHITE
CONTROL BOX (On/Off)
24
WIRING SCHEMATIC - ELECTRIC SPREADER
(Dual Variable Control)
SPINNER
MOTOR
12V DC
CCW
ROTATION
CONVEYOR
FEED MOTOR
12V DC
BLACK
RED
BLACK
RED
A B
A B
VIBRATOR
LIGHT
HARNESS
MAIN
HARNESS
WHITE
BATTERY
HARNESS
TO VEHICLE IGNITION
SWITCH "RUN" OR
ACESSORY FUSED
TERMINAL
BLACK
VEHICLE
BATTERY
1 2 3 4
1 2 3 4
A B
A B
25
BLUE
WHITE
YELLOW
GREEN
BROWN
VIOLET
RED
BLACK
RED
VEHICLE
GROUND
PARTS LIST INTRODUCTION
Our dealership network stands by to provide you with any assistance you may require, including genuine Sno-Way
service parts. All parts should be obtained from or ordered through your dealer. Give complete information about the
part as well as the Model Number and Serial Number of your machine.
Record the Serial Number in the space provided in your Owner’s Manual for quick reference. The Serial Number for the
unit is on a plate located on the left frame gusset of the Hopper Frame.
"Right" and "Left" are determined from a position sitting on the Operators Seat of the vehicle.
We reserve the right to make changes or improvements in the design or construction of any part without incurring the
obligation to install such changes in any unit previously delivered.
USING THIS PARTS LIST
Below is parts listing with four columns. The first column is the "ITEM", the second is the "PART NUMBER", The third is
the "DESCRIPTION" and the fourth is the "QUANTITY".
The "ITEM" is the number used in the corresponding illustration.
The "PART NO." Is the number used to order replacement parts. If a number does not appear
in the column the part is only available by ordering the complete assembly.
The "DESCRIPTION" is the name of the replacement part. At times the name
may be indented, this means that the indented parts are part of the preceding
assembly.
The "QTY." Is the quantity needed to service the assembly
illustrated, not the complete product.
ITEM
1
2
3
PART NO.
DESCRIPTION
96100083
96001529
98100036
O-ring
Elbow
Capscrew, Hex.,3/8"-16NC x 7/8"
QTY.
1
3
9
26
CONVEYOR DRIVE AND IDLER
NOTE: SEE FOLLOWING PAGES
FOR MOTOR DRIVE DETAIL
6
15
7**
3
2
4
5
13
14
2
2
10
1
11
8
21
22
16
10
7
1
2
6
10
8
21
10
7**
12
9
20
17
18
19
7
6
26
7
1
2 7
1
6
6
23
7
25
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
6
PART NO.
98100355
98100339
96104651
98100356
96104736
98100357
98100124
98100224
96104644
98100354
98100505
96106838
96106459
13
14
15
16
17
18
27
96107246
96109229
98100389
96104634
98100236
96106730
96108602
96104638
96104723
24
DESCRIPTION
QTY.
Set Screw, 1/4"-28 x 1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LN, 3/8"-16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Bearing, Flanged, 1- 1/8” ID (Includes item 1) . . . . . . . . . . . . . . . . . . . . . . 1
CB, Short Sq. NeckBolt, 3/8"-16 x 1-1/4", SS . . . . . . . . . . . . . . . . . . . . . . . 2
Take-Up Frame, Left, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HHCS, Hex, 3/8"-16 x 7/8", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PW, 3/8", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Key, Square, 1/4” x 2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Sprocket, Drive, 6 Tooth (Includes item 10) . . . . . . . . . . . . . . . . . . . . . . . . 2
Set Screw, 5/16"-18 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HHCS, 1/2"-13 x 1", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Kit, 15" Wide Chain, Master Link, V-Box
(includes item 14-qty 4 & item 15-qty 4) . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit, 10" Wide Chain, Master Link, V-Box
(includes item 14-qty 4 & item 15-qty 4) . . . . . . . . . . . . . . . . . . . . . . . . 1
Link, Chain V-Box (includes item 14-qty 2 & item 15-qty 2) . . . . . . . . . . 1
Clevis Pin, .265 x 1.60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pin, Cotter, 3/32" x 3/4". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Sprocket, 24 Tooth, 1.00" Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Key, Square, 1/4” x 1.00" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Gearbox, Electric, 10 Inch, 50:1 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Gearbox, Electric, 15 Inch, 50:1 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 Inch Wide Gearbox, 20:1 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 Inch Wide Gearbox, 20:1 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CONVEYOR DRIVE AND IDLER
ITEM
PART NO.
DESCRIPTION
19
20
26
96104724
96104733
96104735
98100503
98100504
98100125
96104726
96113414
96114368
96104730
96104731
Take-Up Frame, Right, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 Inch Wide H-Frame, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 Inch Wide H-Frame, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HHCS, 5/16"-18 x 1-1/4", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Nut, 5/16"-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washer, Lock 3/8", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Shaft w/ Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Shaft w/ Coupler (Dual Electric V-Box Only) . . . . . . . . . . . . . . . . . . . . . . . . 1
10 Inch Wide Chain Guard, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 Inch Wide Chain Guard, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bearing, 1" Tapped Pillow Block (Includes item 1) . . . . . . . . . . . . . . . . . . . 2
27*++
28*++
29*+++
30*+++
31*+++
32*++
33*++
34*++
96104739
96104646
96108750
96108751
96108752
96108750
96108751
96108752
Chain, Conveyor, 5’ 10" Wide, 78 Links, X= 8" . . . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 6’ 10" Wide, 93 Links, X= 8" . . . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 8’ 15" Wide, 121 Links, X=8" . . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 9’ 15" Wide, 136 Links, X= 8" . . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 10’ 15" Wide, 150 Links, X= 8" . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 8’ 15" Wide, 119 Links, X= 10" . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 9’ 15" Wide, 134 Links, X= 10" . . . . . . . . . . . . . . . . . . . . 1
Chain, Conveyor, 10’ 15" Wide, 148 Links, X= 10" . . . . . . . . . . . . . . . . . . . 1
21
22
23
24
25
QTY.
* Not Shown
** Not Used In 5’ & 6’ Spreaders With Serial Numbers Ending in 300000 Or Later
++ Includes items 14 & 15
+++ Includes items 14 & 15; Also order 96106838 (item 12) - Quantity 2
CONVEYOR CHAIN TAKE-UP BRACKET
x
X = 8" OR 10"
28
MOTOR PLATE & DRIVE - GAS SPREADER
11
12
5
3
2 5
4
2
5 7
8
4
9
10
6
13
14
15
11
12
1
26
23
22
22
2
21
19
16
27
17
5
18
24
20
4
5
5
25
29
MOTOR PLATE & DRIVE - GAS SPREADER
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
PART NO.
96114472
96104668
96104669
98100236
98100354
96104635
96107876
98100225
98100217
96104670
96111334
98100235
98100124
98100255
96107991
98009027
98100359
96104652
98100357
96104645
98100358
98100123
98100112
98100355
96104635
DESCRIPTION
QTY.
Kit, Rubber Hold Down Strap (Includes items 27 & 28) . . . . . . . . . . . . . . . 2
Collar, Locking, 1" I.D. (Includes item #6) . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sprocket, 12 Tooth, 1" I.D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key, Square, 1/4" x 1". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Set Screw, 5/16-18 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chain, Drive, 8.0 and 10.5 HP Briggs/Honda,
#40 - 31 Link Pairs (62 total links) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chain, Drive, 10.5 HP Intek, #40 - 30 Link Pairs (60 total links). . . . . . . . . 1
Capscrew, Hex, 5/16-18 x 5/8, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Washer, Lock, 5/16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sprocket, 52 Tooth Electric Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Clutch, Assy., V-Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Nut, Hex Nylock, 3/8-16, SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Washer, Flat, 3/8", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Engine Base, 10 Inch Wide, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Engine Base, 15 Inch Wide, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Nut, Hex, 1/4-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Bracket, Clutch Locator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 1/4-20 x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Bolt, Carriage, 3/8-16 x 1, SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bearing, Flanged, 1" I.D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 3/8-16 x 7/8, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Sprocket, 16 tooth, 1" Bore (Includes item #6) . . . . . . . . . . . . . . . . . . . . . . 1
Nut, Hex Nylock, 5/16-18, SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Washer, Plain, 5/16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Capscrew, Hex, 5/16-18 x 3/4, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Set Screw, 1/4- 28 x 1/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chain, Drive, #40 - 31 Link Pairs (62 total links)
(Note: For 5 & 6 ft. spreaders, chain reduction will be needed) . . . . . . . . 1
Pan Head Machine Screw, #6-32 x 5/8", SS . . . . . . . . . . . . . . . . . . . . . . . 4
Nut, Nylock, #6-32, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
30
MOTOR PLATE & DRIVE - ELECTRIC SPREADER
1
4
5
6
3
2
7
8
8
9
28
10
Includes 60 Tooth
Components:
Item 1 - 96110357
Item 9 - 96110354
Item 10 - 96110352
Item 25 - 96104634
Item 26 - 96110426
11
12
12
13
4
12
14
15
16
20
21
17
18
19
22
18
25
12
23
24
11
12
26
27
5
4
31
MOTOR PLATE & DRIVE - ELECTRIC SPREADER
ITEM
1
2
3
4
5
6
7
8
9
10*
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28**
PART NO.
96106731
96110357
98100214
98100125
98100339
98100124
96106732
98100493
98100494
96110436
96110354
96106734
96110352
98100236
98100354
96104668
96104652
98100355
98100112
98100123
98100118
96114472
98100359
98100356
96104634
96110426
98100357
96111777
DESCRIPTION
QTY.
Electric Motor Plate, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bracket, Electric Motor Mount (60 Tooth Sprocket) . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 3/8"-16 x 3/4", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Washer, Lock, 3/8", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Nut, Hex Nylock, 3/8"-16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Washer, Flat, 3/8", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Sprocket, 12 Tooth, 5/8” Bore, (Includes item XX) . . . . . . . . . . . . . . . . . . . 1
Key, Square, 3/16" x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Set Screw, 1/4"-20 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chain, Drive, Electric V-Box, (46 and 48 tooth Drives),
#40 - 31.5 Link Pairs (64 total links)
(May require link reduction on your application) . . . . . . . . . . . . . . . . . . . . 1
Chain, Drive, Electric V-Box, (60 Tooth Drive Sprocket) . . . . . . . . . . . . . . 1
Sprocket, 48 tooth (Includes items 12). . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Sprocket, 60 tooth (8 Foot Electric V-Box Spreaders) . . . . . . . . . . . . . . . . 1
Key, Square, 1/4" x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Set Screw, 5/16"-18 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Collar, Locking, 1" I.D., (Includes item 12) . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bearing, Flanged, 1" I.D., (Includes item 15) . . . . . . . . . . . . . . . . . . . . . . . 1
Set Screw, 1/4"-28 x 1/4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Mount, Electric Motor, 10 Inch Wide, SS . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Mount, Electric Motor, 15 Inch Wide, SS . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 5/16"-18 x 3/4, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Washer, Plain, 5/16", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Locknut, Hex Nylon Insert, 5/16"-18, SS . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Kit, Strap, Rubber Hold Down (Includes items 21 & 22) . . . . . . . . . . . . . . 2
Pan Head Machine Screw, #6-32 x 5/8", SS . . . . . . . . . . . . . . . . . . . . . . . 8
Nut, Hex Nylock, #6-32, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Bolt, Carriage, 3/8"-16 x 1, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bolt, Carriage, 3/8"-16 x 1-1/4", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Sprocket, 24 Tooth, 1.00" Bore, (Includes items 12) . . . . . . . . . . . . . . . . . 1
Chain, Drive, #40 - 29 Link Pairs (58 total links) . . . . . . . . . . . . . . . . . . . . 1
HHCS, 3/8"-16 x 7/8" SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Kit 60 Tooth Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
* Item #10 used to be a 46 tooth sprocket. Due to design development changes, item #10 has changed to a 48 tooth sprocket.
Spreaders with 46 tooth sprockets will require chain reduction to accommodate the smaller 46 tooth sprocket.
** If you have a 48 tooth, you can convert to a 60 tooth using this kit. This conversion will add greater torque to conveyor chain.
32
DUAL MOTOR PLATE & DRIVE - ELECTRIC SPREADER
6
3
15
4
16
17
9
5
7
7
14
11
2
12
3
19
8
13
4
4
18
4
9
1
3
10
20
17
21
27
28
23
24
26
29
7
17
33
25
22
DUAL MOTOR PLATE & DRIVE - ELECTRIC SPREADER
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
PART NO.
96113414
96113413
98100236
98100354
96112900
98100128
98100124
96102034
98100125
98100120
98009226
98100139
96102016
98100214
96106732
98100339
96110436
96106734
96104668
96114472
98100359
98100356
96104652
98100355
98100357
DESCRIPTION
QTY.
Shaft, Swingaway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Sheave, 7" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key, Square, 1/4" x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Set Screw, 5/16"-18 x 3/8" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Belt, AX33, (1/2" x 35" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CB, 3/8"-16 x 2-1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Washer, Plain, 3/8", A Wide, SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pulley, 2" Idler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Washer, Lock, 3/8", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Nut, 3/8"-16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Washer, Lock, 1/4", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bolt, Hex Washer Head, 1/4"-20 x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Sheave, 1-1/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 3/8-16 x 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Sprocket, 12 Tooth, 5/8" Bore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Motor Plate, 10" Wide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Nut, Hex Nylock, 3/8"-16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chain, 31.5 Link Pairs (64 total links) [48 Tooth] . . . . . . . . . . . . . . . . . . . . 1
Sprocket, 48 Tooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Collar, Locking, 1" I.D., (Includes item 6) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Mount, Electric Motor, 10" Wide, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pan Head Machine Screw, #6-32 x 5/8", SS . . . . . . . . . . . . . . . . . . . . . . . 4
Kit, Rubber Hold Down Strap (Includes items 22 & 24) . . . . . . . . . . . . . . . 2
Nut, Nylock, #6-32, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bolt, Carriage, 3/8-16 x 1", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bolt, Carriage, 3/8-16 x 1-1/4", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Bearing, Flanged, 1" I.D., (Includes item 28) . . . . . . . . . . . . . . . . . . . . . . . 1
Set Screw, 1/4"-28 x 1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HHCS, 3/8"-16 x 7/8" SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
34
ELECTRIC THROTTLE
8
7
8
1
7
5
2
Throttle Pin
(facing engine)
4
6
3
NOTE: Improper installation can
result in damage to the engine
choke throttle linkage.
ITEM
1
2
3
4
5
6
7
8
9
35
PART NO.
96109187
96109189
96109190
96107961
96104773
96107080
98100502
98100501
98100240
98100336
98100334
9
9
DESCRIPTION
QTY.
Kit, Throttle, 6.0 HP Intek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kit, Throttle, 8 or 9 HP Briggs & 10.5 HP Intek . . . . . . . . . . . . . . . . . . . . .
Kit, Throttle, 11 HP Honda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bracket, Electric Throttle (order applicable kit). . . . . . . . . . . . . . . . . . . . . .
Motor, Electric Throttle (order applicable kit) . . . . . . . . . . . . . . . . . . . . . . .
Electric Throttle Arm, 6.0 Intek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric Throttle Arm, 8.0 HP Briggs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric Throttle Arm, 11.0 HP Honda. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nut, Nylock, #6-32, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pan Head Machine Screw, #6-32 x 5/8", SS . . . . . . . . . . . . . . . . . . . . . . .
Washer, Plain, 1/4 SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nut, Nylock, 1/4-20 SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bolt, Hex, 1/4-20 x 3/4, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
3
3
2
2
2
DECAL AND DECAL LOCATION
7
11
5
2
4
3
7
5
6
9
2
2
10
4
3
12
10
8
13
1
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14*
15*
PART NO.
96104557
96107040
DESCRIPTION
QTY.
Decal, Warning, Flying Debris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal,’Sno-Way’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Do Not Enter Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Important, Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Do Not Exceed GVWR. . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, gasoline is flammable . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Do Not Ride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Keep All Guards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plate, Serial No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Rotation & Pinch Point . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Keep Hands & Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Warning, Shut Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal, Caution, Hot Engine Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal Kit, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal Kit, Electric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
3
2
2
2
1
2
1
1
2
1
1
1
1
1
* Not Shown
36
SPREADER BODY
2
3
1
2
4
3
4
5
8
7
6
10
9
11
8
12
25
14
7
13
26
15
28
16
27
8
7
24
17
23
11
11
29
22
ITEM
1
2
3
4
5
37
PART NO.
96114362
96114363
99100429
99100522
99100674
98100112
98100331
98100123
96114373
96114379
99100461
99100517
99100678
21 20
18
30
19
31
32
DESCRIPTION
QTY.
Top Screen, 5’. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top Screen, 6’. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top Screen, 8’. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top Screen, 9’. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top Screen, 10’. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
HHCS, 5/16"-18 x 3/4". SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washer, Lock, 5/16", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washer, Plain, 5/16", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Inverted Vee, 5’, SS (Includes items 6-8) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Inverted Vee, 6’, SS (Includes items 6-8) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Inverted Vee, 8,’ SS (Includes items 6-8) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Inverted Vee, 9’, SS (Includes items 6-8) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Inverted Vee, 10’, SS (Includes items 6-8) . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPREADER BODY
ITEM
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PART NO.
98100357
98100124
98100339
96104749
96104749
96104653
96104750
98100336
96104640
96104751
96104762
98100355
98100220
98100237
96107051
96104756
96104654
96104757
98100240
98100127
98109186
96104759
96104761
96114434
96104748
96104746
98100213
98100359
96114222
96114223
96114221
96100334
DESCRIPTION
QTY.
HHCS, 3/8"-16 x 7/8". SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PW, 3/8", A Wide, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
LN, 3/8"-16, Nylon Insert, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10 Inch Wide Rear Wiper Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 Inch Wide Rear Wiper Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10 Inch Wide Rubber Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15 Inch Wide Rubber Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Locknut, Nylon Insert, 1/4"-20, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
10" Wide Idler Roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15" Wide Idler Roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bearing, Take-Up (Includes item 14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Set Screw, 1/4"-28 x 1/4". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Nut, Hex, 5/8"-11 SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Capscrew, Hex, 5/8"-11 x 6", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Battery Box, Spreader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Battery, 12 Volt Dry Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
10" Wide Rear Rubber Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15" Wide Rear Rubber Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Washer, Plain, 1/4", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bolt, 1/4"-20 x 1-1/2", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Handle, Hood, Rubber Trim Strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Assy, 10" Wide Cover, Engine, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Assy, 10" Wide Cover, Electric Motor, SS . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Assy, 15" Wide Cover, Engine, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Assy, 15" Wide Cover, Electric Motor, SS . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10" Wide Door, Feed Gate, SS (For SN Before 300000,
, also order Item 29) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15" Wide Door, Feed Gate, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
10" Wide Handle, Feed Gate, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
15" Wide Handle, Feed Gate, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Knob, Locking Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 3/8" x 1-1/2", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bolt, Carriage, 3/8"-16 X 1.00", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bracket, Brush. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Brush, Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bottom Brush Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Capscrew, Hex, 1/4"-20 x 3/4". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
38
10" CHUTE/SPINNER ASSEMBLY
1
8
11
7
5
6
7
4
10
9
11
6
7
7
2
10
9
3
12
4
14
15
13
4
4
7
6
4
15
14
14
7
15
15
16
2
REAR
17
39
5
6
10" CHUTE/SPINNER ASSEMBLY
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO.
96114371
96104685
96114442
96107707
98100205
98100357
98100125
98100124
96104625
96104633
98100213
98100339
96107706
96104629
98009159
96104628
98100230
DESCRIPTION
QTY.
10" Wide - Standard Chute/Spinner Assy, SS . . . . . . . . . . . . . . . . . . . . . .
Chute Pin, 1/2" x 14", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chute Hanger Bracket, DS, SS (With Spreader S.N. 300000 or later) . . .
Chute Hanger Bracket, DS, SS (With Spreader S.N. 299999 or earlier) . .
Hairpin Cotter, 3/32" x 2-1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capscrew, Hex, 3/8"-16 x 7/8", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Lock, 3/8 SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Flat, 3/8, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Shaft, 16" Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pillow Block Bearing - 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capscrew, Hex, 3/8"-16 x 1-1/4", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locknut, Nylon Insert, 3/8"-16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Chute, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chute Hanger Bracket, PS, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Rod - 10" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cotter Pin, 3/32” x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spinner Disk-SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clevis Pin, 1/4” x 2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
1
1
5
4
4
8
1
2
4
4
1
1
3
4
1
1
40
15" CHUTE/SPINNER ASSEMBLY
1
8
10
7
5
6
9
7
4
11
10
7
6
7
9
2
11
3
20
4
12
14
15
13
18
4
4
19
7
4
6
15
14
14
15
7
15
16
REAR
2
17
41
5
6
15" CHUTE/SPINNER ASSEMBLY
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NO.
99100451
99100435
96104685
96114442
96107707
98100205
98100357
98100125
98100124
96104625
96104626
96104633
98100213
98100339
96107706
96104629
98009159
96104628
98100230
96114575
98100334
98100336
DESCRIPTION
QTY.
15" Wide - Standard Chute/Spinner Assy, SS . . . . . . . . . . . . . . . . . . . . . .
15" Wide - Extended Chute/Spinner Assy, SS . . . . . . . . . . . . . . . . . . . . . .
Chute Pin, 1/2" x 14", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chute Hanger Bracket, DS, SS (With Spreader S.N. 300000 or later) . . .
Chute Hanger Bracket, DS, SS (With Spreader S.N. 299999 or earlier) . .
Hairpin Cotter, 3/32" x 2-1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capscrew, Hex, 3/8"-16 x 7/8", SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Lock, 3/8 SS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Flat, 3/8, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Shaft, 16" Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Shaft, 28" Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pillow Block Bearing - 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capscrew, Hex, 3/8"-16 x 1-1/4", SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locknut, Nylon Insert, 3/8"-16, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Chute, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chute Hanger Bracket, PS, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Rod - 10" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cotter Pin, 3/32” x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spinner Disk-SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clevis Pin, 1/4” x 2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plate, Bearing Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bolt, Hex, 1/4-20 x 3/4, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nut, Nylock, 1/4-20 SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
1
1
5
4
4
8
1
1
2
4
4
1
1
3
4
1
1
2
4
4
42
CAB CONTROL - GAS SPREADER
1
4
5
3
6
2
7
9
8
11
12
(RED)
13
(BLACK)
14
10
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART NO.
99100555
96108645
96106025
96105926
96107113
96102480
96106095
96106846
96109135
96108646
96107143
96107144
96107142
96105042
DESCRIPTION
* If Harness Has Molded Connectors, Purchase Connector Repair Kit (#10) For Connector or Terminal Repair.
43
QTY.
Controller Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Harness, Main Section, 15 Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Harness, Cigarette Lighter Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Switch, On/Off/Starter, Illuminated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Switch, Throttle, Intermittent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Switch, Clutch, Intermittent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Cover, Plastic Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Kit, Micro-Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Kit, Connector Repair (includes connectors and terminals). . . . . . . . . . . . .1
Harness, Spreader, 8 Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Positive Lead, Battery-Starter, Honda . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Positive Lead, Battery-Starter, Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Negative Lead, Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Start Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
ON/OFF CONTROL - ELECTRIC SPREADER
2
1
3
4
5
10
9
5
4
4,5
11
12
7
15
13
18
6
17
14
8
16
21
26
Includes:
2 9 10
11 12 13
14 16 21
23
24
22
25
19
20
MOTOR DUTY CYCLE:
Motor is not a continuous duty cycle motor.
If the motor becomes hot to the touch, the motor is approaching
heat limits. Be sure to allow adequate cooling of motor
before using the spreader again.
ITEM
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
96106630
96105891
96105946
96105947
96105948
96105940
96105942
Harness, On/Off Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Relay, 70A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Connector, Harness Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Terminal, Female, 10-12 AWG, Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Terminal, Female, 12-16 AWG, Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connector, Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Terminal, Male Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Decal, Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Grommet, 1/2” dia. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Wire, Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw, Self Tapping #10 x 1" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Breaker, Circuit, 40A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Terminal, 1/4", Female Push-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Connector, Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tap, 1/4", ATC/ATO Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tap, 1/4", Mini Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Controller, On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Strip, Hook and Loop Fastener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Terminal, Female. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connector, Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Motor, Electric, 1/2 HP, including Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Harness, Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tie, Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Bag of Parts (On/Off Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Boot, Cable (use with ring terminal connection) . . . . . . . . . . . . . . . . . . . . . 1
Cap Cover, Harness End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Package, Electric Spreader Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Gasket (supplied with Motor, item 19). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
14
15
16
17
18
19
20
21
22
23
24
25
26
96104893
96106728
98100037
96102344
96002085
96101845
96002083
96101832
96105793
96105943
96105941
96111764
96106628
96106729
96106374
96105082
99100621
96111763
QTY
44
DUAL VARIABLE CONTROL - ELECTRIC SPREADER
10
3
2
4
1
15
16
12
11
14
5
MOTOR DUTY CYCLE:
Motors (#6 and #9) are not
continuous
duty
cycle
motors. If a motor becomes
hot to the touch, the motor is
approaching heat limits. Be
sure to allow adequate
cooling of motor before using
the spreader again.
10
10
8
9
7
NOTE:
Individual wiring harness
connectors, identified "A"
through "E", can be ordered
(See page 46). If a connector
is not shown on page 46, the
complete component or
harness must be ordered.
45
6
13
ITEM
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
96115024
96113421
96104893
Control, Dual Electric, V-Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Harness, Bat, DEVBX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Grommet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Tie, Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Harness, Main DEV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Motor, Electric, 1/3 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Gasket (Order Separately). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Gasket (Supplied with Motor, item 9). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Motor, Conveyor Feed, 1/2 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Cap Cover, Harness End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cap, Metri Pack, 2-Way, Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Cap, Apex, 4-Way, Male . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Cap, Metri Pack, 2-Way, Female . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Vibrator Light Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Connector, Flat Blade, Female, 1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Tap, ATC/ATO Fuse, 1/4". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Tap, Mini Fuse, 3/16" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
96114865
96113295
96111763
96113438
96111764
96105082
96115129
96112872
96115130
96115368
96113111
96002083
96101832
QTY
WIRING HARNESS CONNECTORS
A2
A1
B2
C2
C1
B1
D3
D1
D2
ITEM
PART NO.
DESCRIPTION
A
A1
A2
B
B1
B2
C
C1
C2
D
D1
D2
D3
E
96112301
96108661
96108142
96112300
96108662
96108142
96102441
96102442
96102443
96102346
96102347
96102443
96102418
96113111
4 Way Connector, Male ................................................................ A/R
Terminal, Male ............................................................................ 3
Plug, Cavity ................................................................................ 1
4 Way Connector, Female ............................................................ A/R
Terminal, Female ........................................................................ 3
Plug, Cavity ................................................................................ 1
Connector, Male, 2 Pin, 10/12 GA ................................................ A/R
Terminal, Male ............................................................................ 2
Seal ............................................................................................ 2
Connector, Female, 2 Pin, 10/12 GA............................................ A/R
Terminal, Female ........................................................................ 2
Seal ............................................................................................ 2
Secondary Lock .......................................................................... 1
Connector, Flat Blade, Female, 1/4"............................................. A/R
QTY
46
NUMERICAL INDEX
PART NO.
PAGE
ITEM
PART NO.
PAGE
ITEM
96002083
44
45
44
38
44
45
44
34
34
44
46
46
46
46
46
46
46
43
36
40
42
42
40
42
40
42
40
42
27
32
30
30
27
38
27
30
28
27
30
32
34
38
38
30
32
34
30
30
40
42
27
28
28
28
28
14
16
13
32
14
16
13
13
8
12
D
D1
D3
C
C1
C2
D2
6
14
8
8
8
16
16
14
14
9
9
16
25
6
25
18
12
9
20
28
3
18
14
27
10
19
2
13
20
3
9
2
2
18
19
24
25
26
96104733
96104735
96104736
96104739
96104746
96104748
96104749
96104750
96104751
96104756
96104757
96104759
96104761
96104762
96104773
96104893
28
28
27
28
38
38
38
38
38
38
38
38
38
38
35
44
45
43
44
45
44
44
43
44
44
44
44
44
44
44
43
43
44
27
44
44
44
44
27
32
32
34
32
34
27
43
36
38
35
43
43
43
43
27
40
20
20
5
27
26
25
9
10
12
18
19
24
24
13
4
9
3
14
24
10
15
2
4
6
18
7
17
3
4
5
3
7
23
12
20
1
10
22
18
1
6
15
10
19
12
9
15
17
4
5
13
12
12
13
13
96002085
96100334
96101832
96101845
96102016
96102034
96102344
96102346
96102347
96102418
96102441
96102442
96102443
96102480
96104557
96104625
96104626
96104628
96104629
96104633
96104634
96104635
96104638
96104640
96104644
96104645
96104646
96104651
96104652
96104653
96104654
96104668
96104669
96104670
96104685
96104723
96104724
96104726
96104730
96104731
47
96105042
96105082
96105793
96105891
96105926
96105940
96105941
96105942
96105943
96105946
96105947
96105948
96106025
96106095
96106374
96106459
96106628
96106630
96106728
96106729
96106730
96106731
96106732
96106734
96106838
96106846
96107040
96107051
96107080
96107113
96107142
96107143
96107144
96107246
96107706
PART NO.
96107707
96107876
96107961
96107991
96108142
96108602
96108645
96108646
96108661
96108662
96108750
96108751
96108752
96109135
96109187
96109189
96109190
96109229
96110352
96110354
96110357
96110426
96110436
96111334
96111763
96111764
96111777
96112300
96112301
96112872
96112900
96113111
96113295
96113413
96113414
96113421
96113438
96114221
96114222
96114223
96114362
96114363
96114368
96114371
PAGE
ITEM
42
40
42
30
35
30
46
46
27
43
43
46
46
28
28
28
28
28
28
43
35
35
35
27
32
32
32
32
32
34
30
44
45
44
45
32
46
46
45
34
45
46
45
34
28
34
45
45
38
38
38
37
37
28
40
13
3
3
6
4
15
A2
B2
18
2
11
A1
B1
29
32
30
33
31
34
10
1
1
1
14
10
9
1
26
9
18
10
26
7
19
9
28
B
A
12
5
15
E
6
2
24
1
2
8
31
29
30
1
1
25
1
NUMERICAL INDEX
PART NO.
PAGE
ITEM
PART NO.
PAGE
ITEM
PART NO.
PAGE
ITEM
96114373
96114379
96114434
96114442
37
37
38
40
42
30
32
34
42
45
45
45
45
45
30
40
42
34
44
30
32
37
32
34
30
32
37
27
30
32
34
38
40
42
32
34
40
42
38
34
34
40
42
38
40
42
32
34
30
38
27
30
40
42
30
5
5
25
3
3
1
20
23
18
5
1
11
13
14
16
15
15
11
11
23
17
2
19
10
22
18
4
7
12
5
7
7
7
7
3
9
6
6
21
6
12
4
4
27
10
10
2
14
8
15
8
7
17
17
11
98100236
27
30
32
34
38
35
38
30
37
35
42
35
38
42
27
32
34
38
40
42
27
30
32
34
27
30
32
34
38
27
32
34
27
30
32
34
38
40
42
30
30
32
34
38
27
32
32
35
35
28
28
27
38
37
42
17
4
11
3
16
7
20
14
3
9
19
8
11
20
2
4
17
8
11
11
10
5
12
4
1
24
15
28
14
4
24
26
6
19
27
29
6
5
5
21
17
23
25
28
15
7
8
6
5
21
22
11
22
1
1
99100451
99100461
99100517
99100522
99100555
99100621
99100674
99100678
42
37
37
37
43
44
37
37
1
5
5
1
1
25
1
5
96114472
96114575
96114865
96115024
96115129
96115130
96115368
98009027
98009159
98009226
98100037
98100112
98100118
98100120
98100123
98100124
98100125
98100127
98100128
98100139
98100205
98100213
98100214
98100217
98100220
98100224
98100225
98100230
98100235
98100237
98100240
98100255
98100331
98100334
98100336
98100339
98100354
98100355
98100356
98100357
98100358
98100359
98100389
98100493
98100494
98100501
98100502
98100503
98100504
98100505
98109186
99100429
99100435
48
SNO-WAY® INTERNATIONAL, INC.
Hartford, WI 53027 USA
Website: www.snoway.com
©2013 Sno-Way® International
NOTES
DEALER PRE-DELIVERY CHECKLIST
The following inspections MUST be accomplished prior to delivering the SNO-WAY® V-BOX GAS or
ELECTRIC SPREADER to the customer. Place an X ⌧ in the box after accomplishing each item on the
checklist.
CHECK THAT
Parts have not been damaged in shipment. Repair or replace items that are loose, dented or
missing.
All covers, guards and decals are in place and attached securely.
The drive chain and the conveyor chains are at the proper tension.
Baffles can be adjusted to all positions.
Controller and electrical wiring is properly installed.
Gasoline engine or electric drive motor is operating properly.
Inverted V is installed properly (If applicable: All Electric V-Box (EV) models.
Chute has been lined up and spinner shaft - coupling interface mates properly.
Start the vehicle engine and place an X ⌧ in the box after accomplishing each item.
CHECK THAT
Unit does not start until START switch is depressed.
Drive shaft and spinner rotate freely.
Drive rotation is correct (clockwise from top of hopper).
Speed can be adjusted through speed range with controller.
Burst sequence operates when clutch switch is depressed.
Listen for abnormal noises or vibrations; Repair or replace as necessary.
Ignition switch safety shutoff functions correctly. (If on-off controller is used.)
DELIVERY CHECKLIST
The following checklist is to be accomplished with the customer present, place an X ⌧ in the box after
accomplishing each item.
After giving the customer his operating manual, instruct him to read it PRIOR to operating the
spreader. If he has any questions or does not understand part(s) of the manual, ask him to contact the dealer for answers or explanations BEFORE operating the unit.
Record the spreader serial numbers, date of purchase, purchaser’s name and address, and the
dealers name, address and phone number in the space provided on page 1 of the owner’s manual.
Explain spreader connect and disconnect procedures.
Demonstrate controller operation and burst function.
Fill out Warranty Registration Card and mail COPY 1 to the factory to validate Warranty. NO Warranty claims can be honored if the Warranty Card is not on file at the factory.
SNO-WAY® INTERNATIONAL, INC.
Hartford, WI 53027 USA
Website: www.snoway.com
©2013 Sno-Way® International
Download PDF