1
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: ANSI Z21.11.2B, VOLUME II FOR UNVENTED ROOM HEATERS.
GVFS20P
PROPANE
GVFS20N
NATURAL GAS
UNVENTED MILLIVOLT
SYSTEM
CERTIFIED FOR THE UNITED STATES USING ANSI METHODS.
SAFETY INFORMATION
!
WARNING
If the information in these instructions are
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use
any phone in your building.
•
Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
•
If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the supplier.
- This is an unvented gas-fired heater that
uses air (oxygen) from the room in which it is
installed. Provisions for adequate combustion and
ventilation air must be provided.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonfireplaces.com • ask@napoleonproducts.com
10.00$
1.23
W415-0559 / C / 10.04.10
2
TABLE OF CONTENTS
1.0
2.0
3.0
INSTALLATION OVERVIEW
INTRODUCTION
3
4
2.1
2.2
2.3
2.4
5
5
6
7
DIMENSIONS
GENERAL INSTRUCTIONS
GENERAL INFORMATION
RATING PLATE INFORMATION
INSTALLATION
3.1
3.2
3.3
3.4
3.5
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
COMBUSTION AND VENTILATION AIR PROVISIONS
DETERMINING CONFINED OR UNCONFINED SPACE
GAS INSTALLATION
OPTIONAL WALL SWITCH / THERMOSTAT
MOBILE HOME INSTALLATION
8
8
9
10
11
11
FINISHING
12
4.1
4.2
4.3
4.4
12
12
12
13
CAST FRONT INSTALLATION AND REMOVAL
SCREEN INSTALLATION AND REMOVAL
LOGO PLACEMENT
LOG PLACEMENT
OPTIONAL BLOWER INSTALLATION
14
5.1
5.2
14
14
BLOWER INSTALLATION AND CONNECTION
SWITCH CONNECTIONS
OPERATION
ADJUSTMENT
15
16
7.1
7.2
16
16
VENTURI ADJUSTMENT
FLAME CHARACTERISTICS
MAINTENANCE
17
8.1
8.3
8.2
17
18
18
OXYGEN DEPLETION SENSOR PILOT CLEANING
PILOT INDICATOR LIGHT BATTERY REPLACEMENT
ORIFICE REPLACEMENT
REPLACEMENTS
TROUBLE SHOOTING
WARRANTY
SERVICE HISTORY
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
W415-0559 / C / 10.04.10
19
21
24
25
3
1.0 INSTALLATION OVERVIEW
Cast top, see “FINISHING - CAST
FRONT INSTALLATION AND
REMOVAL” section.
Blower, see “OPTIONAL
BLOWER
INSTALLATION” section.
Door, see “FINISHING
- SCREEN
INSTALLATION AND
REMOVAL” section.
Rating Plate, see
“RATING PLATE
INFORMATION”
section.
W415-0559 / C / 10.04.10
4
2.0 INTRODUCTION
!
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
WARNING
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
ANY CHANGES TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS PROHIBITED.
Under no circumstances should this appliance be modified.
Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fire or injury.
Risk of burns. The appliance should be turned off and cooled before servicing.
Do not install damaged, incomplete or substitute components.
Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges
may be sharp.
Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing and
operating the appliance. Never obstruct the front opening of the appliance.
If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it
serviced. Keep burner and control compartment clean.
Do not burn wood or other materials in this appliance.
Children and adults should be alerted to the hazards of high surface temperature and should stay away to
avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to accidental contact burns. A physical barrier is recommended
if there are at risk individuals in the house. To restrict access to an appliance, install an adjustable safety gate
to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and
draperies.
Ensure you have incorporated adequate safety measures to protect infants/toddlers from touching hot
surfaces.
Clothing or other flammable material should not be placed on or near the appliance.
Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from
hot surfaces. These screens and guards must be fastened to the floor.
Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
It is imperative that the control compartments, burners and circulating blower and its passageway in the
appliance are kept clean. The appliance should be inspected before use and at least annually by a qualified
service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding
material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other
flammable vapours and liquids.
Furniture or other objects must be kept a minimum of 4 feet away from the front of the appliance.
Do not use this appliance if any part has been under water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the control system and any gas control which has been
under water.
Do not allow fans to blow directly into the appliance. Avoid any drafts that alter burner flame patterns.
Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this appliance.
Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your home.
If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have it serviced
by a qualified technician before operating it again.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all
plastic bags, these are not toys and should be kept away from children and infants.
As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as
well as having a Carbon Monoxide Detector installed in the same area to defend you and your family against
Carbon Monoxide.
The appliance screen must be in place when the appliance is operating.
Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.
Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or
damage to decorations, a T.V. or other electronic components.
3.4B
W415-0559 / C / 10.04.10
5
2.1
DIMENSIONS
19 1/4"
9 5/8"
25 3/8"
15 3/4"
2.2
GENERAL INSTRUCTIONS
!
WARNING
* CARBON MONOXIDE POISONING MAY LEAD TO DEATH
EARLY SIGNS OF CARBON MONOXIDE POISONING RESEMBLE THE FLU, WITH HEADACHE,
DIZZINESS AND/OR NAUSEA. IF YOU HAVE THESE SIGNS, THE HEATER MAY NOT BE WORKING
PROPERLY. GET FRESH AIR AT ONCE! HAVE HEATER SERVICED.
SOME PEOPLE---PREGNANT WOMEN, PERSONS WITH HEART OR LUNG DISEASE, ANEMIA,
THOSE UNDER THE INFLUENCE OF ALCOHOL, THOSE AT HIGH ALTITUDES--- ARE MORE
AFFECTED BY CARBON MONOXIDE THAN OTHERS.
THE APPLIANCE IS ONLY FOR USE WITH THE TYPE OF GAS INDICATED ON THE RATING PLATE.
THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES.
OBJECTS PLACED IN FRONT OF THE HEATER SHOULD BE KEPT A MINIMUM OF 48” AWAY FROM
THE FRONT FACE OF THE APPLIANCE.
USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH
THIS APPLIANCE. USING NON-LISTED ACCESSORIES AND REPLACEMENT PARTS (BLOWERS,
LOUVRES, TRIMS, GAS COMPONENTS, VENT COMPONENTS, ETC.) COULD RESULT IN A SAFETY
HAZARD AND WILL VOID THE LIMITED LIFETIME WARRANTY.
NOT DESIGNED FOR USE WITH A GLASS DOOR. SCREEN MUST BE CLOSED WHEN APPLIANCE IS
IN OPERATION.
THIS APPLIANCE MUST NOT BE INSTALLED IN A BEDROOM OR BATHROOM.
This gas appliance should be installed and serviced by a qualified installer to conform with local codes.
Installation practices vary from region to region and it is important to know the specifics that apply to your
area, for example: in Massachusetts State:
• The appliance off valve must be a “T” handle gas cock.
• The flexible connector must not be longer than 36“.
• The appliance is not approved for installation in a bedroom or bathroom unless the appliance is a direct
vent sealed combustion product.
• A carbon monoxide detector is required in all rooms containing gas fired appliances.
• WARNING: This product must be installed by a licensed plumber or gas fitter when installed within the
commonwealth of Massachusetts.
• Un-vented room appliance shall be installed in accordance with 527 CMR 30.00 and 248 CMR 3.00
through 7.00.
• Sellers of un-vented propane or natural gas-fired space / room appliances shall provide to each purchaser
a copy of 527 CMR 30.00 upon the sale of the appliance from http://www.napoleonfireplaces.com/
Webshare/installation_manuals/mass_requirements.pdf
W415-0559 / C / 10.04.10
6
In absence of local codes, install the appliance to the current National Fuel Gas Code, ANSI Z223.1
Installation Code which can be obtained from:
American National Standards Institute Inc.
or
National Fire Protection Association Inc.
1430 Broadway
Batterymarch Park
New York, NY 10018
Quincy, MA 02269
The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The appliance must be
isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa). When
installed with a blower the junction box must be electrically connected and grounded in accordance with local
codes. In the absence of local codes, use the current ANSI / NFPA 70 National Electric Code. In the case
where the blower is equipped with a power cord it must be connected into a properly grounded receptacle.
The grounding prong must not be removed from the cord plug.
We suggest that our gas
hearth products be installed
As long as the required clearance to combustibles is maintained,
and serviced by professionals
the most desirable and beneficial location for the appliance is in the
who are certified in the U.S.
center of a building, thereby allowing the most efficient use of the
by the National Fireplace
heat created. The location of windows, doors and the traffic flow in
Institute® (NFI) as NFI Gas
the room where the appliance is to be located should be considered.
Specialists
www.nficertified.org
If the appliance is installed directly on carpeting, vinyl tile or other
combustible material other than wood flooring, the appliance shall be installed on a metal or wood panel
extending the full width and depth. NOTE: This does not apply to stoves.
* Air shortage caused by an inadequate air supply, improper log positions, the addition of foreign or
unapproved materials or the failure to properly maintain the appliance, may result in incomplete combustion of
the fuel. Incomplete combustion results in soot being deposited inside the firebox as well as surfaces outside
the appliance. If any soot deposits are observed, shut off the appliance immediately and arrange for it to be
serviced by a qualified technician.
4.2C
2.3
GENERAL INFORMATION
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND
QUALITY!
GVFS20
Altitude (FT)
Max. Input (BTU/HR)
NG
LP
0-2,000
0-2,000
23,000
23,000
Min. Inlet Gas Supply Pressure
4.5" Water Column
11" Water Column
Max. Inlet Gas Supply Pressure
7" Water Column
13" Water Column
3.5" Water Column
10" Water Column
Manifold Pressure (Under Flow Conditions)
When the appliance is installed at elevations above 2,000ft, and in the absence of specific recommendations from
the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each
additional 1,000ft. Expansion / contraction noises during heating up and cooling down cycles are normal and to be
expected.
No external electricity (110 volts or 24volts) is required for the gas system operation.
This appliance is equipped with a pilot light safety system referred to as an oxygen depletion sensor and is designed to
turn off the appliance if not enough fresh air is available.
W415-0559 / C / 10.04.10
7
RATING PLATE INFORMATION
CONFORMS TO: ANSI Z21.11.2a-2008, UNVENTED GAS FIRED ROOM HEATER
THIS IS A GAS-FIRED UNVENTED
ROOM HEATER THAT REQUIRES
ADEQUATE COMBUSTION
AND VENTILATION AIR.
THIS APPLIANCE IS NOT FIELD
CONVERTIBLE FOR USE WITH
OTHER FUELS.
**0-2000FT (0-610m)
23,000 BTU/h
18,000BTU/h
DIAGRAM
AGRAM TO AID THE OPERATION
OF THIS FIREPLACE
A
M
P
LE
MODEL GVFS20-N
THIS UNIT IS NOT APPROVED FOR
BEDROOM, BATHROOM AND
BED-SITTING ROOM
INSTALLATION.
MODEL GVFS20-P
P
ALTITUDE
INPUT
REDUCED INPUT
MANIFOLD PRESSURE: 3.5" WATER COLUMN
MINIMUM SUPPLY PRESSURE: 4.5" WATER COLUMN
MAXIMUM SUPPLY PRESSURE: 7.0" WATER COLUMN
SIT CONTROL: # 820.638
OPERATING PILOT OXYPROTECTOR: # 8214
**0-2000FT (0-610m)
0m)
23,000 BTU/h
BTU//h
BTU
00BT
00
BTU
U/h
18,000BTU/h
WATER
ER COLUMN
COLUMN
MANIFOLD PRESSURE: 10" WATER
SSURE: 111"
1" WATER
WATER C
OLUMN
MINIMUM SUPPLY PRESSURE:
COLUMN
RESSURE
ESSURE:: 13" WA
W
ATER C
OLUM
LUMN
MAXIMUM SUPPLY PRESSURE:
WATER
COLUMN
36
SIT CONTROL: # 820.63
820.636
ILOT OXYPROTEC
OXYPROTECT
T OR
OR:: # 88436
4366
OPERATING PILOT
OXYPROTECTOR:
TY
Y HAVING
H AV I N G JURISDICTION
J UR
URIS
ISD
D IC
C TIO
TION
N
**ABOVE 2,000FT, CONSULT LOCAL AUTHORITY
FLAME
ADJUSTMENT
ON / OFF
CONTROL
NOT FOR USE WITH SOLID
OLID FUEL
FUEL..
MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS
A
4”
B
2"
C
2"
45
B
A
o
C
WARNING:
RNIN DO NOT ADD ANY MATERIA
RNING:
MATERIAL TO THE APPLIANCE, WHICH
WILL COME IN CONTAC
CONTACT WITH THE FLAMES, OTHER THAN
THAT SUPPLIED BY THE MA
MAN
MANUFACTURER WITH THE APPLIANCE.
SCREEN
EEN MUST BE IN PLAC
PLACE WHILE THE APPLIANCE IS IN OPERATION.
48” MINIMUM TO CEILING FROM STOVE TOP
P
WOLF STEEL LTD.
24 NAPOLEON ROAD. BARRIE, ONTARIO
TARIO
RIO L4M 4Y8 CANAD
CANADA
S
2.4
ELECTRICAL RATING: 115V 0.82AMP, 60HZ
OPTIONAL FAN KIT: GS-64KT
SERIAL NUMBER GVFS20
IGNITOR
W385-0337 / J
INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to
the model, venting and gas type of the appliance.
For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.
W415-0559 / C / 10.04.10
8
3.0 INSTALLATION
THIS GAS HEATER SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform
with local codes. Installation practices vary from region to region and it is important to know the specifics that
apply to your area.
Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing
and operating the heater. Never obstruct the front opening of the heater.
As long as clearances to combustibles is kept within the required distances, the most desirable and beneficial
location for a heater is in the centre of a building, thereby allowing the most efficient use of the heat created.
The location of windows, doors and the traffic flow in the room where the heater is to be located should be
considered.
MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES:
A. 4"
B.
2"*
C. 2"
Heater should not be installed directly on carpeting.
Minimum 48" from top to ceiling.
* If less than 5" clearance is maintained between the back of the heater and the back wall, it will be necessary
to disconnect the gas pipe to move the heater out for installation or service of the blower.
3.1
COMBUSTION AND VENTILATION AIR PROVISIONS
This appliance shall not be installed in a confined space or unusually tight construction unless provisions are
provided for adequate combustion and ventilation air.
The National Fuel Gas Code, ANSI Z223.1 / NFPA 54 defines a confined space as a space whose volume is
less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances
installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per
1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space.
Rooms communicating directly with the space in which the appliances are installed, through openings not
furnished with doors are considered a part of the unconfined space.
17.1A
The GVFS20 is rated at 23,000 BTU's per hour for natural gas and propane gas and therefore requires a
minimum unconfined space of 1,150 cubic feet.
W415-0559 / C / 10.04.10
9
3.2
DETERMINING CONFINED OR UNCONFINED SPACE
To determine the volume of the room where the appliance is to be installed, multiply the width x the length x
the ceiling height of that room measured in feet. If any adjoining rooms are connected by grilles or openings
such as kitchen pass-throughs, etc., the volume of those rooms may be added to the total.
Multiply the room volume by 1000 and divide this amount by 50 to determine the maximum BTU/hr that the
space can support with adequate combustion and ventilation air.
Add the Btu/hr of all fuel burning appliances located within the space such as gas furnace, gas water
appliance, etc. Do not include direct vent gas appliances which draw their input and output air from and to the
outdoors.
Unusually tight construction is defined as construction where:
A) Walls and ceilings exposed to the outside atmosphere have a continuous water vapour retarder with a
rating of 1 perm (6 x 10-11 kg per pa-sec-m2) or less with openings gasketed or sealed, and
!
WARNING
IF THE AREA IN WHICH THE APPLIANCE MAY BE OPERATED IS SMALLER THAN THAT DEFINED AS
AN UNCONFINED SPACE OR IF THE BUILDING IS OF UNUSUALLY TIGHT CONSTRUCTION, PROVIDE
ADEQUATE COMBUSTION AND VENTILATION AIR BY ONE OF THE METHODS DESCRIBED IN THE
NATIONAL FUEL GAS CODE ANSI Z223.1/ NFPA 54 , AIR FOR COMBUSTION AND VENTILATION, OR THE
APPLICABLE LOCAL CODE.
IF THE AREA IN WHICH THE APPLIANCE MAY BE OPERATED DOES NOT MEET THE REQUIRED VOLUME
FOR INDOOR COMBUSTION AIR, COMBUSTION AND VENTILATION AIR SHALL BE PROVIDED BY ONE
OF THE METHODS DESCRIBED IN THE ANSI Z223.1 / NFPA 54, THE INTERNATIONAL FUEL GAS CODE,
OR APPLICABLE LOCAL CODES.
B) Weather stripping has been added on openable windows and doors, and
C) Caulking or sealants are applied to areas such as joints around window and door frames, between sole
plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical,
and gas lines, and at other openings.
An unvented room appliance is recommended for use as a secondary heat source rather than as a primary
source. Gas combustion produces water vapour which could occur at the rate of approximately one ounce of
water for every 1,000 BTU/hr of gas input. During the cold weather season, indoor humidity levels tend to be
low. Consequently, this water vapour can enhance the living space. However if a problem should occur:
A) Ensure sufficient combustion and circulation air
B) Use a dehumidifier
C) Do not use the unvented room appliance as a primary heat source
Without sufficient fresh air for proper operation, poor fuel combustion can result. Carbon Monoxide is a result
of poor combustion.
If additional fresh air is required, use one of the methods described in the National Fuel
Gas Code, ANSI Z223.1 / NFPA54 or the applicable local code.
Room Volume = Length x Width x Height
ROOM 2
Max BTU/hr = Room Volume x 1000 / 50
If for example:
The length of the rooms is 10 feet,
The width of Room 1 is 10 feet,
The width of Room 2 is 15 feet,
The height of the rooms is 8 feet.
The volume of Room 1: 10x10x8 = 800 cubic feet
The volume of Room 2: 10x15x8 = 1200 cubic feet
ROOM 1
HEIGHT
LENGTH
W
ID
TH
19.1B
W415-0559 / C / 10.04.10
10
EXAMPLE 1:
In this example, because there is no door to the adjoining room, the volume of the adjoining room may be
added to the volume of the room with the heater to get a total unconfined space.
The total unconfined space: 800 + 1200 = 2000 cubic feet.
Maximum BTU/h: 2000x1000 = 40,000 BTU/h
50
19.2
If there are no more fuel burning appliances within this space then the 23,000 BTU/h input of the heater is
suitable to be installed. This also assumes that the construction of this space is not unusually tight.
EXAMPLE 2:
If in this example a solid door separates Room 1 from Room 2, the volume of Room 2 could not be used. In
this case the maximum BTU/h would be:
Maximum BTU/h: 800x1000 = 16,000 BTU/h
50
19.3
This would be considered a confined space since it can not support the 23,000 BTU/h input of the heater and it
would be necessary to provide adequate combustion and ventilation air to Room 1.
3.3
GAS INSTALLATION
!
WARNING
RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH
AS SPARKS OR OPEN FLAMES.
SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT
WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE
PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT
THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND
ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.
HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS
LINE AT TEST PRESSURES ABOVE 1/2 PSIG.
VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.
Installation and servicing to be done by a qualified installer. Do not use open flame.
A.
Move the appliance into position and secure.
B.
If equipped with a flex connector the appliance is designed to accept a 1/2” gas supply. Without the
connector it is designed to accept a 3/8” gas supply. The appliance is equipped with a manual shut off
valve to turn off the gas supply to the appliance.
C.
Connect the gas supply in accordance to local codes. In the absence of local codes, install to the
current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI
Z223.1 / NFPA 54 in the United States.
D.
When flexing any gas line, support the gas valve so that the lines are not bent or kinked.
E.
Check for gas leaks by brushing on a soap and water solution.
30.2
W415-0559 / C / 10.04.10
11
3.4
OPTIONAL WALL SWITCH / THERMOSTAT
!
WARNING
DO NOT CONNECT EITHER THE WALL SWITCH, THERMOSTAT OR GAS VALVE DIRECTLY TO 110
VOLT ELECTRICITY.
For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient
location. Route a 2 strand, solid core millivolt wire from the valve to the wall switch or millivolt thermostat. The
recommended maximum lead length depends on wire size:
WIRE SIZE
MAX. LENGTH
3
14 gauge
100 feet
16 gauge
60 feet
2
18 gauge
40 feet
1
Disconnect the existing wires from terminals 1 and 3 (from the
ON/OFF switch) and replace with the leads from the wall switch / millivolt thermostat.
50.1
3.5
MOBILE HOME INSTALLATION
Suitable for mobile home installation where the mobile home has been permanently placed on its site.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where
not prohibited by local codes.
For mobile home installations, the appliance must be fastened in place. It is recommended that the appliance
be secured in all installations. See “REPLACEMENTS” section for the levelling / securing kit specific to your
appliance.
29.2
W415-0559 / C / 10.04.10
12
4.0 FINISHING
4.1
CAST FRONT INSTALLATION AND REMOVAL
!
WARNING
SCREENS MUST BE CLOSED WHILE THE APPLIANCE IS IN OPERATION.
A.
B.
C.
Lift the top cast piece off of the heater.
Detach the front cast piece from the side pieces by removing
the screws from the brackets located in the upper inside
corners.
3
FRONT
2
SCREWS
BRACKET
Slide the front straight up to remove.
Follow the above steps in reverse in order to reinstall
the cast front. Ensure that the tabs on the underside of
the front fit behind the front legs.
4.2
SCREEN INSTALLATION AND REMOVAL
A.
Unscrew the four screws (one in each corner) securing the screen
to the heater face.
B.
Remove screen from heater.
Follow the above steps in reverse in order to reinstall the screen.
FRONT
TAB
Four
Screws
FRONT
LEGS
4.3
LOGO PLACEMENT
Remove the backing of the logo supplied and centre over the logo installation holes, as indicated.
LOGO
W415-0559 / C / 10.04.10
13
4.4
LOG PLACEMENT
!
WARNING
LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE
PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY. DELAYED IGNITION
AND CARBON / SOOT DISTRIBUTION THROUGHOUT THE LIVING AREA MAY OCCUR.
THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.
DO NOT PLACE CHARCOAL EMBERS, VERMICULITE OR CHARCOAL LUMPS ON THIS BURNER.
ALL PREVIOUSLY APPLIED LOOSE MATERIAL (GLOWING EMBERS) MUST BE REMOVED PRIOR TO
REAPPLICATION.
DO NOT CHANGE OR SUBSTITUTE THE GLOWING EMBER MATERIAL PROVIDED WITH THE
APPLIANCE. IF REPLACING, USE ONLY REPLACEMENT GLOWING EMBERS AVAILABLE FROM
YOUR LOCAL AUTHORIZED DEALER / DISTRIBUTOR.
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL ADVERSELY EFFECT THE APPLIANCE’S
PERFORMANCE AND MAY RESULT IN CARBON / SOOT DEPOSITS INSIDE THE APPLIANCE AND ON
SURROUNDING SURFACES.
76.2B
In order to assemble the log set, the screen and cast front must be removed, see Cast Front / Screen Removal
in the Finishing section of this manual.
A. Place the rear log, as shown, onto the rear log support brackets. Bend the bracket on the right side to
help retain the rear log against the back of the firebox.
B.
Place the hole in the underside of log #2 onto
the locating screw, on the left side of the
burner. The fibre burner is formed to cradle
the centre of the log.
C.
Place the hole in the underside of log #3 onto
the locating screw, on the right side of the
burner. The bottom branch of log #3 sits in
front of, and against, the right end of log #2.
D.
Reinstall the screen & front.
POSITIONING THE LOGS IMPROPERLY WILL CAUSE FLAME IMPINGEMENT AND CARBONING.
W415-0559 / C / 10.04.10
14
5.0 OPTIONAL BLOWER INSTALLATION
5.1
BLOWER INSTALLATION AND CONNECTION
(SEE LOCATION AND CLEARANCES IN INSTRUCTION MANUAL)
A.
Cut and remove the tie securing the blower switch wires to
the heat shield.
B.
Connect the white wire coming from below the heater to the
terminal on the blower.
C.
Connect the black blower wire to the black wire coming from
below the heater.
D.
Insert the clips on the blower housing into the cutouts in the
rear shield. Push down to lock the clips into position.
E.
Secure the blower using the screw and lock washer supplied.
7
9
8
1
NOTE: Ensure that all the wires are tucked into the blower switch
housing.
This heater comes equipped with a pilot indicator light that blinks
every few seconds when the pilot is on. For more information see step A,
section 5.2
5.2
7
4
4
2
3
SWITCH CONNECTIONS
A.
5
Open the switch housing by removing the top screw.
THERMAL DISC
BRACKET
B.
With the 2 screws and extension bracket supplied in the heater baggie,
fasten extension bracket to the thermal disc bracket. Install bracket
assembly as shown, using 2 of the screws supplied. Connect the flagged
leads to the terminals of the thermal disc 7 .
C.
Remove the knock out from the switch housing label 8 . Install the
variable speed switch (rheostat) into the housing with the wires facing
up. Secure the switch to the housing using the pal nut and the knob
supplied.
7
D.
Connect the male connector on the switc to the
female connector coming from the heater 9 .
E.
Pilot Indicator Light: Install the batteries as shown.
Replace the batteries annually.
THERMAL DISC
EXTENSION
BRACKET
7
9
NOTE: If replacing the pilot indicator light ,
ensure that the red wire lead connects to the
red lead of the thermopile and black to white.
F.
Tuck all of the wires into the switch housing and
close. Secure using the screw removed in step A.
W415-0559 / C / 10.04.10
8
15
6.0 OPERATION
!
WARNING
,)<28'2127)2//2:7+(6(,16758&7,216(;$&7/<$),5(25(;3/26,210$<5(68/7
&$86,1*3523(57<'$0$*(3(5621$/,1-85<25/2662)/,)(
,)$33/,&$%/($/:$<6/,*+77+(3,/27:+(7+(5)257+(),5677,0(25,)7+(*$66833/<+$6
581287:,7+7+(*/$66'22523(1('255(029('
,IDSSOLDQFHVKXWVRIIGRQRWUHOLJKWXQWLO\RXSURYLGHIUHVKDLU,IDSSOLDQFHNHHSVVKXWWLQJRIIKDYHLWVHUYLFHG.HHSEXUQHU
DQGFRQWUROFRPSDUWPHQWFOHDQ
When lit for the first time, the appliance will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing
of the logs and the “burn-in” of internal paints and lubricants used in the manufacturing process and will not occur again. After extended
periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for a few hours.
This is caused by dust particles burning off. In both cases, open a window to sufficiently ventilate the room.
FOR YOUR SAFETY READ BEFORE LIGHTING:
Ɣ This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.
Ɣ Before operating smell all around the appliance area for gas and next to the floor because some gas is heavier than air and will settle on the floor.
Ɣ Use only your hand to push in and turn the gas control knob. Never use tools. If the knob will not push in and turn by hand, do not try
to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.
Ɣ Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance
and replace any part of the control system and any gas control which has been under water.
WHAT TO DO IF YOU SMELL GAS:
ƔDo not try to light any appliance.
ƔDo not touch any electric switch; do not use any phone in your building.
Ɣ Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.
Ɣ If you cannot reach your gas supplier, call the fire department.
LIGHTING INSTRUCTIONS:
When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed.
$ STOP! Read the above safety information on this label.
% Set the thermostat to lowest setting.
& Turn off all electric power to the appliance.
' Open the control door. Turn the gas knob clockwise to off.
( Wait five (5) minutes to clear out any gas. If you smell gas including near the floor, STOP! Follow “B” in the above safety information
on this label. If you don’t smell gas go to the next step.
) Find pilot located in front of the back log.
G. Turn gas knob counter-clockwise to pilot.
H. Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob fully depressed for one minute, then
release. If pilot does not continue to burn repeat steps 3 through 7.
, With pilot lit, turn gas knob counter-clockwise to on. When the pilot has been turned off,
ignition of the main burner may be delayed from 1-2 minutes. When the pilot has been left
burning, ignition of the main burner should occur almost immediatley.
- If equipped with remote on-off switch, main burner may not come on when you turn the valve to on. Remote switch must be in
the on position to ignite burner.
K. Turn on all electric power to the appliance.
TO TURN OFF GAS
A. Turn off all electric power to the appliance if service is to be performed.
%Push in gas control knob slightly and turn clockwise to off. Do not force.
47.1
W415-0559 / C / 10.04.10
16
7.0 ADJUSTMENT
7.1
VENTURI ADJUSTMENT
!
WARNING
CARBON CAN BE DISTRIBUTED IN SURROUNDING LIVING AREA IF THE AIR SHUTTER IS
IMPROPERLY ADJUSTED.
49.5
This appliance has an air shutter that has been factory set open according
to the chart below:
Regardless of venturi orientation, closing the air shutter will cause a more
yellow flame, but can lead to carboning. Opening the air shutter will cause a
more blue flame, but can cause flame lifting from the burner ports. The
flame may not appear yellow immediately; allow 15 to 30 minutes for the
final flame color to be established.
VENTURI
BURNER
AIR
SHUTTER
OPENING
ORIFICE
AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED
INSTALLER!
49.1
AIR SHUTTER OPENINGS
7.2
NG
1/16”
LP
7/16”
FLAME CHARACTERISTICS
It’s important to periodically perform a visual check of the pilot and burner flames. Compare them to the illustrations provided. If any flames appear abnormal call a service person.
54.5
W415-0559 / C / 10.04.10
17
8.0 MAINTENANCE
MAINTENANCE
! WARNING
MAINTENANCE
TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE.
APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED.
DO NOT USE ABRASIVE CLEANERS.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing. This appliance and its venting system
should be inspected before use and at least annually by a qualified service person. The appliance area must
be kept clear and free of combustible materials, gasoline or other flammable vapors and liquids. The flow of
combustion and ventilation air must not be obstructed.
1.
In order to properly clean the burner and pilot assembly, remove the logs, rocks and/or glass to
expose both assemblies.
2.
Keep the control compartment, media, burner, air shutter opening and the area surrounding the logs
clean by vacuuming or brushing, at least once a year.
3.
Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or
are not burning properly.
4.
Check to see that the pilot flame is large enough to engulf the flame sensor and/or thermocouple /
thermopile as well as reaches the burner.
5.
Replace the cleaned logs, rocks or glass. Failure to properly position the media may cause carboning
which can be distributed in the surrounding living area.
6.
Check to see that the main burner ignites completely on all openings when turned on. A 5 to 10
second total light-up period is satisfactory. If ignition takes longer, consult your local authorized dealer /
distributor.
40.16
8.1
OXYGEN DEPLETION SENSOR PILOT CLEANING
This procedure must be performed by a
CORRECT PILOT FLAME
qualified service person!
(Clean, stable, pronounced
Inspect the pilot for any visible
blue flame).
contamination or debris (usually lint, pet
hair, spider webs, carpet fibre, etc.) and remove.
INCORRECT PILOT FLAME
(Flame lifts upwards,
becomes unstable with more
of an orange tip).
Disconnect the pilot from the pilot tubing line,
using a 7/16” wrench. Blow out the housing in
the same direction as the gas flow. Re-install
the pilot tube, turn on the gas and check
for leaks.
If this does not improve the performance,
replace the ODS with an exact replacement. The
device is tamper resistant with no field serviceable
parts.
46.1
W415-0559 / C / 10.04.10
18
8.3
PILOT INDICATOR LIGHT BATTERY REPLACEMENT
If the pilot indicator light no longer flashes and the pilot is burning,
the batteries may require replacing.
Four "AA" batteries are required and should be replaced annually.
8.2
A.
Open the switch housing by removing the top screw, then
pivoting the box open.
B.
Remove the 4 "AA" batteries and replace using the new
ones.
C.
Pivot the box closed and re-secure using the screw
removed in step A.
-
+
+ -
-
+
+
-
ORIFICE REPLACEMENT
A.
Remove the cast front and the screen, see "CAST FRONT INSTALLATION AND
REMOVAL" and "SCREEN INSTALLATION AND REMOVAL" section in the
FINISHING segment of this manual.
B.
Remove the 2 securing screws indicated and remove the burner assembly.
C.
The orifice is located on the left hand side.
D.
Reinstall the burner ensuring that the venturi tube fits over the orifice and replace the
screws.Care should be taken not to damage the gas pipe. When removing and
replacing the orifice, using a 9/16" socket wrench, a 7/8" back-up wrench must be
used on the manifold, located below the housing, to ensure that the aluminium tubing
does not twist or kink.
W415-0559 / C / 10.04.10
ORIFICE
LOCATION
BURNER
ASSEMBLY
SCREW
LOCATIONS
19
9.0 REPLACEMENTS
Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally
all parts can be ordered through your Authorized dealer / distributor.
FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE
REQUIRED TO HONOUR THE CLAIM.
When ordering replacement parts always give the following information:
• Model & Serial Number of appliance
• Installation date of appliance
• Part number
• Description of part
• Finish
* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR
FURTHER INFORMATION, CONTACT YOUR AUTHORIZED DEALER.
!
WARNING
FAILURE TO POSITION THE PARTS
IN ACCORDANCE WITH THIS
MANUAL OR FAILURE TO USE ONLY
PARTS SPECIFICALLY APPROVED
WITH THIS APPLIANCE MAY
RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY.
41.1
COMPONENTS
REF
PART NO.
DESCRIPTION
1
W135-0254
LOG #1- REAR
2
W135-0249
LOG #2 - LEFT
3
W135-0250
LOG #3 - RIGHT
4
GL-651
LOG SET
5
W725-0050
SIT VALVE - NG
5
W725-0031
SIT VALVE - LP
6
W100-0094
FIBRE BURNER
7
W456-0043
#43 BURNER ORIFICE - NG
7
W456-0055
#55 BURNER ORIFICE - LP
8
W662-0001
NG OXYGEN DEPLETION SENSOR SYSTEM
8
W662-0005
LP OXYGEN DEPLETION SENSOR SYSTEM
9
W080-0756
PILOT BRACKET
10
W357-0001
PIEZO IGNITOR
11*
W385-0334
NAPOLEON® LOGO
12*
W660-0009
ON/OFF SWITCH
13*
W690-0002
THERMAL DISC
14
KB-35
VARIABLE SPEED SWITCH
15*
GZ552
REPLACEMENT BLOWER
16
W135-0233**
FRONT CASTING
17
W135-0232**
SIDE (LEFT OR RIGHT) CASTING
18
W135-0231**
TOP CASTING
19
W080-0757
BRACKET, COLLECTOR
20
W565-0087
SCREEN
21*
W430-0013
CONTROL DOOR MAGNET
22
W010-1307
CONTROL COVER
23*
W750-0149
PILOT LIGHT ASSEMBLY
**FOR OTHER AVAILABLE COLOURS, ADD THESE LETTERS TO THE BASE PART NUMBER:
COLOR
LETTER
FINISH
MAJOLICA BROWN
N
PORCELAIN
W415-0559 / C / 10.04.10
20
ACCESSORIES
REF
PART NO.
DESCRIPTION
24*
F40
REMOTE CONTROL
24*
F50
THERMOSTATIC REMOTE CONTROL
24*
F50DR
THERMOSTATIC REMOTE CONTROL
24*
F50DY
THERMOSTATIC REMOTE CONTROL
24*
F50DK
THERMOSTATIC REMOTE CONTROL
25
GS-65KT
BLOWER KIT
26*
GDSLL-KT
LEG LEVELLING KIT
27*
GS-331S
STOVE TOP INSET - SOAPSTONE
28*
GS-331F
STOVE TOP INSET - GRANITE - GREEN
29*
GS-331N
STOVE TOP INSET - GRANITE - BROWN
30*
W660-0026
PROGRAMMABLE TIMER
18
10
5
7
25
17
8
20
21
17
19
9
4
22
1
14
16
6
W415-0559 / C / 10.04.10
3
2
21
10.0
TROUBLE SHOOTING
!
WARNING
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT,
WITH THE GLASS DOOR OPEN OR REMOVED.
TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE.
APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED.
DO NOT USE ABRASIVE CLEANERS.
SYMPTOM
Main burner goes
out; pilot stays on.
Main burner goes
out; pilot goes out.
PROBLEM
TEST SOLUTION
Pilot flame is not large
enough or not engulfing
the thermopile.
-
Ensure adequate supply pressure.
Replace pilot assembly.
Thermopile shorting /
loose connection.
-
Clean thermopile connection to the valve.
Reconnect.
Replace thermopile / valve.
Remote wall switch wire
is too long; too much
resistance in the system.
-
Shorten wire to connect length or wire gauge.
Faulty thermostat or
switch.
-
Replace.
Insufficient air supply.
-
Open window or door. (Use one of the methods
described in ANSI Z223.1 / NFPA54 or the
applicable local code.)
Have room checked for adequate air exchange.
See “COMBUSTION AND VENTILATION AIR
PROVISIONS” section to ensure adequate air supply.
-
Pilot goes out
when the gas knob
is released.
The gas valve has
an interlock device
which will not allow
the pilot burner
to be lit until the
thermocouple
has cooled. Allow
approximately 60
seconds for the
thermocouple to
cool.
Out of propane gas.
-
Fill the tank.
Pilot flame is not large
enough. (Supply pressure
too low.)
-
-
Service or replace Oxygen Depletion Sensor
System.
Correct piping and / or regulator to provide correct
pressure.
Ensure adequate supply pressure.
System is not correctly
purged.
-
Purge the gas line.
Out of propane gas.
-
Fill the tank.
Pilot flame is not large
enough. (Supply pressure
too low.)
-
Service or replace Oxygen Depletion Sensor
System.
Thermocouple shorting /
faulty.
-
Loosen and tighten thermocouple.
Clean thermocouple and valve connection.
Replace Oxygen Depletion Sensor System.
Test and replace valve.
Faulty valve / high low
knob does not depress
smoothly.
-
Replace.
-
42.4_A
W415-0559 / C / 10.04.10
22
SYMPTOM
Pilot burning;
no gas to main
burner; gas
knob is on ‘HI’;
wall switch /
thermostat is on.
Pilot will not light.
PROBLEM
TEST SOLUTION
Thermostat or switch is
defective.
-
Connect a jumper wire across the wall switch
terminals; if main burner lights, replace switch /
thermostat.
Wall switch wiring is
defective.
-
Disconnect wires from valve. Connect a jumper wire
across terminals 1 & 3; if the main burner lights,
check the wires for defects and / or replace wires.
Main burner orifice is
plugged.
-
Remove stoppage in orifice.
Faulty valve.
-
Replace.
Out of propane gas.
-
Fill the tank.
No spark at pilot burner.
-
Check if pilot can be lit by a match.
Check that the wire is connected to the push button
ignitor.
Check if the push button ignitor needs tightening.
Replace the wire if the wire insulation is broken or
frayed.
Replace the electrode if the ceramic insulator is
cracked or broken.
Replace the push button ignitor.
THERMOCOUPLE
THERMOPILE
PILOT
ELECTRODE BURNER
No gas at the pilot burner.
-
Pilot goes out
while standing;
Main burner is in
‘OFF’ position.
Gas piping is undersized.
-
-
Check that the manual valve is turned on.
Check the pilot orifice for blockage.
Replace the valve / Oxygen Depletion Sensor
System.
Call the gas distributor.
Turn on all gas appliances and see if pilot flame
flutters, diminishes or extinguishes, especially
when main burner ignites. Monitor appliance supply
working pressure.
Check if supply piping size is to code. Correct all
undersized piping.
Pilot flame is not large
enough.
-
ODS Burner requires checking.
Main burner will
not light; or is slow
to light, noisy pilot.
Inlet pressure too high.
-
Adjust inlet pressure to ensure maximum 7.0” W.C.
at gas valve for natural gas and 13.0” W.C. for
propane.
Carbon is being
deposited on
glass, logs,
rocks, media
or combustion
chamber.
Air shutter has become
blocked.
-
Ensure air shutter opening is free of lint or other
obstructions.
Flame is impinging on the
glass, logs, rocks, media
or combustion chamber.
-
Check that the logs are correctly positioned.
Check for ceiling or oscillating fans that may be
influencing the flame.
Open air shutter to increase the primary air. See
“VENTURI ADJUSTMENT” section.
Check the input rate: check the manifold pressure
and orifice size as specified by the rating plate.
Pilot flame blowing off,
missing thermopile.
-
42.4_2_A
W415-0559 / C / 10.04.10
23
SYMPTOM
Flames are
consistently too
large or too small.
Carboning occurs.
PROBLEM
Unit is over-fired or underfired.
TEST SOLUTION
-
A
B
O
PL T
ON
LO
FF
IH
O I
-
PILOT
PILOT SCREW
Exhaust fumes
smelled in room,
headaches.
Air shutter improperly
adjusted.
-
Return air shutter to specified opening, see
“VENTURI ADJUSTMENT” section.
Not enough combustion
air.
-
Increase fresh air supply. (Use one of the methods
described in ANSI Z223.1 / NFPA 54 or the
applicable local code.)
Not enough ventilation air.
-
Increase fresh air supply. (Use one of the methods
described in ANSI Z223.1 / NFPA 54 or the
applicable local code.)
Flame is impinging on
the logs or combustion
chamber.
-
Check that the logs are correctly positioned.
Open air shutter to increase the primary air. See
“VENTURI ADJUSTMENT” section.
Check the input rate: check the manifold pressure
and orifice size as specified by the rating plate
values.
-
Remote wall
switch is in “off”
position; main
burner comes on
when gas knob
is turned to “ON”
position.
If optional catalytic
door is used,
White / grey film
forms on the
glass.
Check pressure readings:
Inlet pressure can be checked by turning screw (A)
counter-clockwise 2 or 3 turns and then placing
pressure gauge tubing over the test point. Check
with burner operating on “HI”. Gauge should read 7”
(minimum 4.5”) water column for natural gas or 13”
(11” minimum) water column for propane.
Outlet pressure can be checked the same as above
using screw (B). Check with burner operating on
“HI”. Gauge should read 3.5” water column for
natural gas or 10” water column for propane.
AFTER TAKING PRESSURE READINGS, BE
SURE TO TURN SCREWS CLOCKWISE FIRMLY
TO RESEAL. DO NOT OVER TORQUE.
Leak test with a soap and water solution.
Wall switch is mounted
upside down.
-
Reverse.
Remote wall switch is
grounding.
-
Replace.
Remote wall switch wire is
grounding.
-
Check for ground (short); repair ground or replace
wire.
Faulty valve.
-
Replace.
Sulphur from fuel is being
deposited on the glass,
logs, rocks, media or
combustion surfaces.
-
Clean glass with recommended gas appliance glass
cleaner. DO NOT CLEAN GLASS WHEN HOT!
If deposits are not cleaned off regularly, the glass
may become permanently market.
-
42.4_3_A
W415-0559 / C / 10.04.10
24
11.0
WARRANTY
NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2008 Quality Assurance
Certificate.
NAPOLEON® products are designed with superior components and materials assembled by trained craftsmen who take great
pride in their work. The burner and valve assembly are leak and test-fired at a quality test station. The complete appliance is
again thoroughly inspected by a qualified technician before packaging to ensure that you, the customer, receives the quality
product that you expect from NAPOLEON®.
NAPOLEON® GAS APPLIANCE PRESIDENT’S LIFETIME LIMITED WARRANTY
The following materials and workmanship in your new NAPOLEON® gas appliance are warranted against defects for as long as
you own the appliance. This covers: combustion chamber, heat exchanger, stainless steel burner, phazer™ logs and embers, rocks,
ceramic glass (thermal breakage only), gold plated parts against tarnishing, porcelainized enameled components and aluminum
extrusion trims.*
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves, thermal switch, switches, wiring, remote
controls, ignitor, gasketing, and pilot assembly are covered and NAPOLEON® will provide replacement parts free of charge during
the first year of the limited warranty.*
Labour related to warranty repair is covered free of charge during the first year. Repair work, however, requires the prior approval of
an authorized company official. Labour costs to the account of NAPOLEON® are based on a predetermined rate schedule and any
repair work must be done through an authorized NAPOLEON® dealer.
* Construction of models vary. Warranty applies only to components included with your specific appliance.
CONDITIONS AND LIMITATIONS
NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary. Simply
provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® reserves the right to have its
representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an authorized
NAPOLEON® dealer your appliance is subject to the following conditions and limitations:
Warranty coverage begins on the date of original installation.
This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.
The gas appliance must be installed by a licensed, authorized service technician or contractor. Installation must be done in accordance with the installation
instructions included with the product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from
other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and chemical cleaners nor
chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs and embers.
This warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been
operated in accordance with the operation instructions and under normal conditions.
After the first year, with respect to this President’s Lifetime Limited Warranty, NAPOLEON® may, at its discretion, fully discharge all obligations with
respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s).
NAPOLEON® will not be responsible for installation, labour or any other expenses related to the reinstallation of a warranted part and such expenses are
not covered by this warranty.
Notwithstanding any provisions contained in the President’s Lifetime Limited Warranty, NAPOLEON’S responsibility under this warranty is defined as
above and it shall not in any event extend to any incidental, consequential or indirect damages.
This warranty defines the obligations and liability of NAPOLEON® with respect to the NAPOLEON® gas appliance and any other warranties expressed or
implied with respect to this product, its components or accessories are excluded.
NAPOLEON® neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.
NAPOLEON® will not be responsible for: over-firing, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees,
hills, mountains, inadequate vents or ventilation, excessive venting configurations, insufficient makeup air, or negative air pressures which may or may not
be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.
Any damages to the appliance, combustion chamber, heat exchanger, plated trim or other components due to water, weather damage, long periods of
dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®.
All parts replaced under the President’s Limited Lifetime Warranty Policy are subject to a single claim.
During the first 10 years NAPOLEON® will replace or repair the defective parts covered by the lifetime warranty at our discretion free of charge. From 10
years to life, NAPOLEON® will provide replacement parts at 50% of the current retail price.
All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.
The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned products are
to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or replace such defect.
Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without
authorization will be refused and returned to sender.
Shipping costs are not covered under this warranty.
Additional service fees may apply if you are seeking warranty service from a dealer.
Warranty labour allowance is only for the replacement of the warranted part. Travel, diagnostic tests, shipping and other related charges are not covered
by this warranty.
ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT
IMPROVEMENTS. NAPOLEON® IS A REGISTERED TRADEMARK OF WOLF STEEL LTD. PATENTS U.S. 5.303.693.801 - CAN.
2.073.411, 2.082.915. © WOLF STEEL LTD.
2.1A
W415-0559 / C / 10.04.10
25
12.0
SERVICE HISTORY
43.1
W415-0559 / C / 10.04.10
26
13.0
NOTES
44.1
W415-0559 / C / 10.04.10
27
44.1
W415-0559 / C / 10.04.10
28
44.1
W415-0559 / C / 10.04.10
Download PDF