AT880
Guide for Customer
ATID Co., Ltd
Copyright ⓒ2006 ATID Co., Ltd. An Unpublished Work – All right reserved.
No part of the contents of this documentation or the procedures described there in may be reproduced or
transmitted in any form or by any means without prior written permission of ATID Co., Ltd.. or its wholly owned subsidiaries ("ATID ").
Owners of ATID products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business
purposes.
Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any
reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting ATID Customer Administration. Electronic versions may either be
downloadable from the ATID web site (www.atid1.com) or provided on appropriate media.
If you visit our web site and would like to make comments or suggestions about this or other ATID publications, please let us know via the “Contact ATID ” page.
Disclaimer
ATID is a registered trademark of ATID Co., Ltd.
AT880 is a registered trademark of ATID Co., Ltd. and of its wholly owned subsidiaries.
ATID Co., Ltd.
#1205, Byuksan/GyungIn Digital Valley II, #481-10,
Gasan-Dong, Gumchon-Gu, Seoul, Korea
Tel: +82-2-544-1436
Fax: +82-2-2113-0040
www.atid1.com
2
Contents
Page
6
Contents
Before using manual for AT880
Chapter 1. Caution when using AT880
7
1. How to use battery correctly
7
2. Caution when using AT880
Chapter 2. Product composition
8
1. Product composition
9
2. Name of each part
10
3. Function of each part
Chapter 3. Basic function
11
1. Switch On Backup Battery
12
2. Attaching and Detaching the battery
13
3. Charging battery
13
4. Power On and Off
15
5. Checking Battery Gauge
16
6. Backup Battery
16
7. Battery replacement
17
8. Soft Reset
17
9. Hard Reset
18
10. Initializing System
19
11. Attaching Micro SD card
20
12. Attaching SIM Card and SAM Card
21
13. Shortcuts setting
21
14. Set up phone password
22
15. Owner information
22
16. LOCK
3
Page
Contents
Chapter 3. Basic function(continues)
23
17. Memory
23
18. Task Manager
24
19. Remove the program
24
20. GPS
25
21. Set screen brightness
25
22. Backlight ON/OFF set up
26
23. Screen adjustment
26
24. Volume and sounds setting
27
25. Sounds and notification
27
26. Set up the Clock and Alarms
28
27. Wireless Manager
28
28. Using keypad
28
29. Inputting Data
29
30. Using <Fnc> Button
29
31. Use of stylus
30
32. Connecting PDA to PC
34
33. Data transfer
Chapter 4. Optional module
37
1. Using 1D or 2D barcode scanner
40
2. Barcode emulator setting
44
3. Barcode scanning
45
4. Wifi Power On /Off Wireless Zero Configuration
46
5. How to connect AP (1)
47
6. How to connect AP (2)
48
7. WiFi Power On /Off Summit client utility
4
Page
Contents
Chapter 4. Optional module(continues)
49
8. Bluetooth connection and termination
50
9. Bluetooth Pairing
52
10.
Bixolon SPP-R200 Printer Demo
53
11.
How to use Phone
53
12.
Dialing
54
13.
Receiving Phone Call
54
14.
Hang off Phone Call
55
15.
Contact List
55
16.
How to search a contact information
56
17.
Add to contact list
57
18.
How to use Text Message
57
19.
Sending Message
58
20.
Receiving Message
58
21.
Replying Message
59
22.
GPS demo application execution
60
23.
Use of camera
61
24.
HF13.56 demo application execution
61
25.
Mifare tag recognition
62
26.
ISO15693 tag recognition
62
27.
SmartCard demo application execution
63
28.
UHF 900MHz demo application execution
Chapter 5. Appendix
67
1. Product specification
5
Before using manual for AT880
User guide inclusive of text, images, logos, product names is either the property of, or used with permission by ATID CO.LTD. The information may not be distributed,
modified, displayed, reproduced (in whole or in part) without the prior written permission of ATID CO.LTD.
There are some differences between user guide and actual function of device.
User guide can be adjusted by ATID CO.LTD without consent of user discretionally.
User guide is written for users who want to use and maintain the AT880. Please read and understand these instruction prior to operating this unit.
Safety information
Your safety is extremely important. Read and follow all warnings and cautions in this document before you handle and operate ATID equipment. If you do not follow
the safety warnings and cautions, you might be seriously injured, and the equipment and data also might be damaged.
■ WARNIING
A warning requires you must pay attention to the operating procedure practice, condition, and statement strictly, or might be injured seriously.
◆ CAUTION
A caution alerts you that you must be observe strictly when you operating procedure, practicing, configuring, for preventing from damage and destruction of
equipment, and loss of data.
● NOTICE
A notice provide you the information which you must needs while you using AT880.
6
Caution when using AT880
Please aware of the manual contents in advance before you handle and operate your AT880 and other ATID Products.
How to use battery correctly
•
In case that you dropped the main body or battery in water, please do not put into the stove or heater for drying. Just keep it in natural drying or contact purchase
place.
•
Please note that the battery terminal doesn’t have to be contacted to metallic object.
•
If you do not use the battery for a long time, please keep it at room temperature after charging.
•
Operating time of battery can be shorter than usual in accordance with loss of battery and use time. In this case, please contact us.
•
You have to use provided adaptor when charging the device.
•
Turn off the device properly then detach or replace the battery.
Caution when using AT880
•
•
•
•
•
•
User careless or products repair would damage the stored data. Manufacturer is not responsible for this damage, so please do back-up the important data
separately.
If you have a problem on product, do not try to repair or disassemble it by yourself, please contact our customer service center.
Do not use your product at the specific places such as hospital, plane and so on where electromagnetic wave or the risk may occur.
Please note that using the device in environment of high temperature and humidity for long hours can make a malfunction of device.
In case of that noise, smoke and odor occur at the device while using product, please disconnect the charger with device and off the power immediately, then
please contact our customer service center.
If you have any other questions on use of device, please contact our customer service center.
Chapter 1. Caution when using AT880
7
Product Composition
This is built on the Windows Embedded Handheld 6.5. The PDA could equip with Barcode Scanner and so on devices as optional items.
Its various function applied to Industry, Enterprise, Logistics and so on, can be used extensively in many fields.
Product composition
Open the packing box and confirm the items as below.
4. USB sync cable
2. Power Adapter and AC cable
3. Standard battery
1. AT880 main body
5. Protect film
*
6. Hand strap
7. Stylus pen
Please contact our customer service in defect of product composition and need to be changed.
Chapter 2. Product composition
8
Name of each part
1D/2D Scanner
(option)
Camera (option)
Earphone jack
Sync cable connector
Charger jack
Camera flash (option)
Cradle connector
Phone receiver
WLAN LED
(option)
Charge LED
Internal HF
Hand strap hole
UHF
Speaker
UHF Connecting port
Volume button
Scan button
Touch Screen
Scan key
Battery
Keypad
Reset button
Chapter 2. Product composition
Microphone
Battery latch
Gun handle
9
Function of each part
NAME
FUNCTION
Camera (option)
It is possible to image capture and save.
Camera flash (option)
You can use the camera with flash
1D/2D Scanner (option)
Laser beam emitted through this window. Please be careful the foreign substances and preventing from the damage.
Warning! Do not look at the laser beam directly.
Charger jack
Enable you to connect to adaptor which provided from factory.
Cradle connector
Enable you to connect to PC or charging the battery while using cradle.
Earphone jack
Enable you to connect to earphone.
Sync cable connector
Enable you to connect and send data to PC via USB sync cable.
Charger LED
Charger LED will be Red when the battery is charging, or will be green when it is charged completely.
Touch screen
Display running programs, and could execute, use, and exit programs via to touch the screen.
Keypad
Enable you to input key value (number, alphabets, symbol), or executing assigned programs.
Reset button
Enable you to perform a warm Reset, Press <Power>button simultaneously, Enable you to perform a hard Reset
WLAN LED (option)
Displays whether the wireless WLAN power supply
Scan key
It is possible to scan barcode or RFID tag
Microphone
Enable you to conduct communication
Internal HF
HF 13.56MHz Embedded module mounting location.
Hand strap hole
Enable you to attach a hand strap or a stylus for the convenience of using, while need to use the device for a long period time.
Speaker
Build-in speaker, which could emit various sound effects.
UHF Connecting port
Enable you to install a UHF 900MHz tag reader module.
Battery
Enable to supply the power to the product.
Battery latch
Enable you to detaching and attaching the main battery.
Scan button (F7, F8)
It is possible to scan barcode or RFID tag
Chapter 2. Product composition
10
Basic Function
PDA battery is composed of main battery and backup battery. A main battery supplies the power to the system and RAM which could keep save the data.
A backup battery could keep save the data of RAM when the main battery discharged completely.
Main Battery: 3.7V 2,970mAh Lithium – polymer
Backup Battery: 3.7V 80mAh Lithium – polymer
◆
Note:
Switch on the backup battery at first beginning of using PDA, and then install the main battery, charge it completely.
Switch On Backup Battery
The image as blow shows the battery compartment, which already removed the main battery.
Slide the lever to right to start to supplying power to the system.
Backup Battery Switch
To attaching main battery to the back battery compartment of the PDA.
To confirm the battery latch locked firmly.
“Refer to 1.2 Battery attaching and detaching”
Connecting adaptor to the PDA adaptor connecting jack, and check if the “Power LED” is Red, and then charging the power completely until it get into Green.
◆
Note:
If the window wallpaper has shown on the screen, press the <power> button for a couple of seconds, so that could shorten the charging times.
Chapter 3. Basic Function
11
Attaching and Detaching the battery
▶ Battery detachment
These images as below, shows the back bottom of the PDA.
Slide the battery latch to the right (UNLOCK side), and then lift the main battery out of the compartment along both sides of groove.
Battery latch
Both sides of groove
▶ Battery attachment
Put the top part of battery into the upward groove, and then press down the bottom of battery
into the battery compartment, slide battery latch to the left (LOCK side) to attach battery firmly.
R/L Battery Attaching
Groove
Chapter 3. Basic Function
12
Charging battery
You have to charge the battery via dedicated adapter, which provided from the factory.
“Power LED” is Red while charging or is Green when charged completely.
▶ Connecting Adapter
1. Plug the adapter cable to 220V socket.
2. Connect adapter DC cable to the “Power connecting jack” of the main body.
3. “Power LED” is Red while charging.
◆
Caution:
You must to charge the battery by using dedicated adapter, which provided from factory, or your device might get damage.
Power On and Off
Press <Power> button one time, the device will enter low-Power mode (Sleep Mode) Under the system is started and the following window is displayed on
the desktop or other Programs is running in the system, press <Power> button once again could activated the system
Icon
Start button
Icon : Display the currently running programs.
Start button : Activates the start menu and then execute a program.
Chapter 3. Basic Function
13
▶ Power On and Off via <Power> Button
Power Off:
1. When the system is in booting status, press <Power> button for a couple of seconds,
then the backlight will be turned off and enter the low-power mode (sleep mode).
2. You can also press <Start Button> -> <Suspend> button to turn the device off.
Power On:
1. When the system power is in the off status, press <Power> button quickly,
then backlight will be turned on and start the system.
2. Connect to the ActiveSync USB cable : the power will be turned on automatically.
Power Button
◆
Note:
Even though the power is in off state, if there was a tiny battery gauge remained, the data of RAM will be saved,
and those programs which have been running for sometime before the power turned off, will be recover rapidly.
If the main battery and backup battery are both in the discharge state, the RAM data will disappear, and the system
will be starting if the power is charged again.
▶ Automatic Power OFF
The device has been powered but has not been used for a period of time, then the system will enter low-power mode (sleep mode) automatically.
You could set the sleep mode time at the power management so that could save power and prolog the battery life.
Power Icon
[Start Button] -> [Setting] -> [Power] -> [advanced]
 You can also double click <Power> Icon to enter this interface.
 You can also press the <Power> button to activate the system,
when the device turned off cause get into the sleep mode.
Chapter 3. Basic Function
14
▶ Battery Discharging
If the main battery discharge completely, the system will not turned on, the device will get into low-power mode (sleep mode) automatically,
and even press the <Power> button, the system will not be turned on. In this case, you should charge the main battery or connect the adaptor
to the adaptor connecting jack of main body, then press the <Power> button to turn on the system.
Checking Battery Gauge
● Note :
Battery life is largely affected from the user using method and surrounding environments.
A 2,970mAh battery is usually needs 6 ~ 12 hours to get charged completely.
▶ Checking Battery Gauge
[Start button] -> [setting] -> [Power] -> [Battery]
Chapter 3. Basic Function
15
▶ Low Power Warning
If the remaining battery gauge cannot support the system running any more, a low power warning message window will be popped up on the screen.
In this case, you need to press the <Power> button to turn off the power, and to charge the battery as soon as possible.
Backup Battery
A backup battery could safely keep the RAM data, even the main battery discharged completely.
◆
Caution:
If the main battery and the backup battery are both discharged, the RAM date will disappear.
Among the running programs, the RAM data will disappear in which are using, and the system
will not be restore to previous state, but rebooting system after start charging.
Battery replacement
You need to purchase a new one if the battery damaged or reached its end of life.
◆
Warning!
Please dispose the used batteries in a designated place.
Chapter 3. Basic Function
16
If there is no response from the system or an application is locked up and stops responding, and when you want to upgrade the firmware,
reset the system is maybe necessary.
Soft Reset
When do you need to perform Soft Reset?
If there is no response for your command from the system, it calls (Hang-up). In this case, you need to perform a soft reset.
Soft reset will end programs and the user memory region will be deleted, but installed programs and data, and so on, are not affected.
[Process of Soft Reset]
Using the stylus pen to press <Reset> button briefly, the system will restarting again, after the screen turns off shortly.
[Result of Soft Reset]
-
System will be restarting.
Operating System will be restarting (Windows CE).
Desktop will appear in about ten seconds.
User’s changed registry information, copied files and
Installed programs will be restored.
Power Button
Reset button
Hard reset
When do you need to perform Hard Reset?
Hard Reset, which is also called Cold Reset, enables to initialize hardware completely. User’s installed programs,
copied files and registry values will keep remained even performed Hard Reset, but the real time and date will be initialized.
So you need to reset the time and date after performed Hard Reset.
You need perform Hard Reset when the Soft Reset cannot restore the system.
[Process of hard reset]
Using stylus pen to Press <Power> Button and <Reset> Button simultaneously, the system will restarting again after the screen turns off shortly.
[Result of Hard Reset]
-
System will be restarting.
Operating System (Windows CE) will be loading and restarting.
Desktop will appear in about ten seconds.
Time and date window will be popped up and need to reset it.
Chapter 3. Basic Function
17
Initializing System
Enter [Boot Menu] and do what you want, when in the situations as below :
1. When you need to restore the original registry information, which has been changed.
2. When you need to initialize “My device” storage spaces.
3. When you need to initialize “Flash Disk” storage spaces.
4. When you need to initialize system to factory default settings.
When you are pressing the <Fnc>button and press the [Reset] button shortly
Power Button
Fnc Button
Reset button
[Boot Menu] window would appear in a couple of seconds.
◆
Caution:
Except for [Clean System], please do not use other functions.
The system might be work not properly if you use other functions on the [Boot Menu].
[Boot Menu]

SD Image Update
It is for the image (BOOT, OS) update by SD Card

Format
My Device and Registry area recover as shipped

Factory Reset
My Device, Registry and Flash Disk area recover as shipped

Exit
Finish the Boot Menu
0. SD Image Update
1. Clean On Exit(No)
2. Factory Reset
3. Exit
Menu Select : Enter No.
[Boot Menu] Start-up Screen
Chapter 3. Basic Function
18
The image as below is battery compartment of , and there are 1EA SIM Card Slot, 1EA SAM Card Slot and 1EA Micro SD Card Slot.
Micro SD card slot
SAM card slot
SIM card slot
Attaching Micro SD card
Push the cover to the right
along arrow direction to
open it.
Chapter 3. Basic Function
Lift the cover up along
arrow direction.
Put Micro SD card into Slot and
press down the cover as arrow
direction.
Push the cover up as arrow
direction to lock it, and attach
the main battery and turn on
the power.
19
You can find the Micro SD Memory Card icon when executing the file explorer, after inserted the Micro SD card.
[Start] -> [File explorer]
Attaching SIM Card and SAM Card
SIM Card and SAM Card can easily insert and pull out along arrow direction.
Chapter 3. Basic Function
20
Shortcuts setting
You want to quickly run frequently used programs You can set the shortcuts function
[Start button] -> [setting] -> [Personal] -> [Button]
Select the button you want to assign as the shortcut, And select the desired program from the program assigned
Set up phone password
If the SIM card is lost or stolen, USIM card in order to prevent the use of others by setting as password
[Start button] -> [setting] -> [Personal] -> [Phone] -> [Security]
Use the password
Change the PIN number
When you use the password and select the “Phone using the PIN (personal identification Number) password
input window is displayed and required to enter the four digit password and select the ‘key’ <Enter>’
◆
Caution:
PIN Code is ‘0000” for protecting USIM card information You can change to own your password.
PUK code is that PIN Code entered incorrectly three times identification Number (PIN) consecutive USIM unlock code. (8digit).
It will be on the USIM card’s envelope or the body Entered incorrectly 10 times in a row when not able to use the USIM card, please note
Chapter 3. Basic Function
21
Owner information
It can set up the owner information (Name, company, address, Telephone, E-mail and Notes
[Start button] -> [setting] -> [personal] -> [owner information]
LOCK
It is for the PDA’s data,
If the handset is not in use for a certain period of time and the switch to the lock status,
You suppose to enter a password to unlock it.
[Start button] -> [setting] -> [LOCK]
Set up the LOCK screen
Chapter 3. Basic Function
LOCK screen
Input the password
22
Memory
You can check the capacity of the memory
[Start button] -> [setting] -> [System] -> [Memory]
Main memory : Usage and remaining capacity can check
Storage card : it can check Flash area or SD care capacity
Task Manager
You can see a list of programs currently being used and the
Amount of memory you have
[Start button] -> [setting] -> [system] -> [Task manager]
You can be stopped by selecting the program
You are using form the list.
Chapter 3. Basic Function
23
Remove the program
This will display a list of programs installed in addition to the Preinstalled programs
[Start button] -> [setting] -> [system] -> [Remove program]
It can be removed from the list, select the program you want to Remove
GPS
You can set the GPS port within the terminal
[Start button] -> [System] -> [GPS]
Do not need to be set separately because it is set by default to the port terminals
are used in GPS.
Chapter 3. Basic Function
24
Set screen brightness
Screen brightness is set to the factory in approximately 70%
[Start button] -> [setting] -> [system] -> [Contrast]
Brightness: you can adjust the brightness of the screen
Backlight ON/OFF set up
Screen brightness, the power consumption is most affected
Because it can be set up suit the user’s needs.
Off screen timeout time can be set
[Start button] -> [Setting] -> [system] -> [Backlight]
Battery Power : When using the Battery power, set up the brightness On/Off.
External power : the brightness of the screen when using an external Power on/ off settings
Chapter 3. Basic Function
25
Screen adjustment
At first beginning of using the device after purchasing or need to use the device for a long period time, if you cannot select the place where you touched with stylus,
you need to reset the coordinate calibration values.
[Start button] -> [setting] -> [system] -> [Screen] -> [align screen]
Volume and sounds setting
You can set up the Volume and sounds.
Set up the volume’s ICON
 You can adjust the volume with products
left volume button (hardware)
Chapter 3. Basic Function
26
Sounds and notification
You can set up the ringing one and vibration and bell sound notification On/OFF.
[Start button] –> [setting] -> [Sounds and notification]
Vibration : Set the vibration amplitude set
Sound : Set the sound notification
Notification : Select the ring type
Set up the Clock and Alarms
Set up the date, time and Alarms
[Start button]-> [setting] -> [Clock and Alarms]
Time : Set the Date and Time
Alarms : Set the Alarms
Chapter 3. Basic Function
27
Wireless Manager
You can control the Bluetooth, Wi-Fi, Phone’s function On/Off.
[Start button] -> [Setting] -> [connect] -> [Wireless manage]
All : It can control the all ON/OFF of WIFI, Bluetooth, and PHONE
Separately : when you click the Buttons (Wi-Fi, Bluetooth, and Phone) It is possible to ON/OFF
 It can be expressed differently depending on the product option
Keypad enables you to input numbers, alphabets and special symbols. And can also execute other set function with <Fnc> button.
Using keypad
When you change the current input language, please press <1<=>ALP> button.
[Number] -> [Lowercase alphabetic characters] –> [Uppercase alphabetic characters]
Order transition.
Inputting Data
Numeric Keypad Mode : Press<1<=>ALP> button or keypad icon on the taskbar to change to the numeric mode and directly press number on the keypad.
Alphabet Keypad Mode : Press <1<=>ALP> button or keypad icon on the taskbar to change to the Lowercase or Uppercase and directly press alphabets or
special symbols on the keypad. Each button has 2 ~ 3 letters or symbols. Press the button once, the first letter or symbol will be inputted,
press twice continuously, then the second letter or symbol will be inputted, and the third letter or symbol need to press button three times
continuously.
Chapter 3. Basic Function
28
Using <Fnc> Button
Press <Fnc> button and other buttons simultaneously can activate functions as below :
Fnc + button
Function description
<Left>, <Light> Cursor Key On the Keypad &
Left Side <Up>, <Down>
Increase or decrease the sound.
<Up>, <Down> Cursor Key on the Keypad
Perform Page Up or Page Down.
<1> ~ <9>
Perform F1 ~ F9 Function Key
<Back Space>
Delete a letter which located after the cursor.
<.>,<0>,<_>
Enable you to input <+> <000> < – > symbols.
Use of stylus
You can tie the stylus to the hand strap hole, so that enable you to use the stylus as like a mouse on a PC
Use of stylus:
●
Select a letter on the soft keypad.
●
Select a program on the desktop or taskbar.
●
Select button, zone or tab bar in a window box or program.
◆ Caution:
Please do not use sharp objects on the touch screen. Use only supplied stylus, otherwise
would bring seriously damage to the touch screen.
Chapter 3. Basic Function
29
ActiveSync program could synchronize between the PC and PDA device, so that enable you to perform program installing, copy, transition, delete and so on operations.
Connecting PDA to PC
Download the latest version of ActiveSync program from Microsoft Windows CE. Website, and install it to your PC.
ActiveSync: Windows XP
Download Address : http://www.microsoft.com/downloads/.
◆
Caution:
You must use ActiveSync v3.7 version or above.
Chapter 3. Basic Function
Click the [Next] Button
Select the license agreement and then, click
the [Next] Button
Input the name of user and group and then,
click the Next Button
Select the license agreement and then, click
the [Next] Button
30
Click the Installation button
ActiveSync are installing
Press End button for termination of installation
Chapter 3. Basic Function
31
Setting PC
[Start button] -> [Programs] -> [Microsoft ActiveSync]
< Windows Xp >
< Win7 / Vista >
Click on the install button
File connection settings, Click the button.
Chapter 3. Basic Function
32
< Windows Xp >
< Win7 / Vista >
USB sync cable connection, select Allow, and then click the OK button.
[Start buttons] -> [setting] -> [connect] -> [USB-PC]
Even connect to PC, synchronization is not good
Please select the Enable advanced network functionality
To use a VPN you can connect your computer to your device
Using the RNDIS.
In this case, please try to connect and after you turn off the
‘Enable advanced network functionality’
Chapter 3. Basic Function
33
Data transfer
Using the USB cable to connect PC and the device.
Connecting state
Disconnecting state
You can check the ActiveSync connecting state on the taskbar.
< Windows XP >
Chapter 3. Basic Function
< Win7 / Vista >
Start - Program– Click Microsoft
ActiveSync
Start – Program – Click Windows Mobile Device
When you connect ActiveSync Click the
explorer menu.
Content on the device when Active sync
Connected, click the browse ICON.
34
< Windows XP >
File/ directory device’s screen
Data transfer screen
Chapter 3. Basic Function
35
Optional module
provided variety of optional modules and in this chapter will provide you the information of each module.
Various optional modules for AT880
1) Barcode reader
-. 1D Laser Barcode Scanner
-. 2D Imager Barcode Scanner (2D Long Range Barcode Option)
2) Wireless LAN – IEEE 802.11 a/b/g/n (Option)
3) Bluetooth
4) UHF 900MHz – GEN2, ISO/IEC 18000-6C
5) HF 13.56MHz – ISO15693, MIFARE, ISO14443 A/B (Option)
6) GPS Module
7) Phone
8) Camera
Chapter 4. Optional module
36
Enable to equip with a compact image engine, which could recognize all the 1D and 2D barcodes.
Using 1D or 2D barcode scanner
Running application
[Start Button] -> [DEMO_BarcodeScan] performing
Chapter 4. Optional module
37
Main window
Start Scan : start reading barcode.
Stop Scan : stop reading barcode
Symbol : Read barcode type name
Length : length of the barcode read
Menu : application pop-up menu.
Exit : Exit the application.
Pop-up menu
Option : Set up the application options
Capturing : image capture by 2D Scanner module
Symbology Config : Set up the Barcode decoding options
Chapter 4. Optional module
38
Option window
Beep : Success the Barcode scanner, beep sound output.
Vibrator : Success the Barcode scanner, working vibrator.
Enable “SCAN” key : Enable “SCAN” key
Enable F7 key on right side : Enable F7 key
Enable F8 key on right side : Enable F9 key
Enable trigger : Enable Gun Trigger key
RAW Data : To set the scan results in the form of raw data
2D scanners only support.
Capturing window
Start Preview : Start preview by 2D scanner
Stop Preview : Stop preview
Do Capture : current screen and save it as a file
Chapter 4. Optional module
39
Symbology Config window
Symbology Selection: Set up the specific decoding options
Set Enable Status: Enable/Disable status of all symbology.
Default All Symbologies: All symbology set as default
Disable All Symbologies : All Symbology Disable.
Enable All Symbologies : All Symbology Enable
Barcode emulator setting
Barcode Emulator program enables you to set the barcode value input type scan button, scan sound (Notes , internet explorer)
When user running the barcode Emulator, who should finish the previous running program.
Running application
[Start Button] -> [File Explorer] -> [My Device] -> [Program Files] -> [ATID_DemoApps] -> BarcodeEmulatorWM.exe
Chapter 4. Optional module
40
Application run complete.
Once the run is complete, the barcode icon on the bottom right
of the screen is registered and can be scan
When user clidk the barcode icon , pop up the main menu and
Can change the settings
Emulator Main Menu
Exit : Exit the application
Vibrator : Upon successful barcode scanning vibrator action
Beep : success the barcode scanning and beep sound output
Key Setup: set up the start barcode scan key
Terminator : select barcode value to be added to the special
Character
Result Type : select how to output barcode value
Chapter 4. Optional module
41
Key Setup
Below keys can set multiple
F1 : Set up for starting when the F1 key is pressed
F2 : Set up for starting when the F2 key is pressed
F7 : Set up for starting when the F7 key is pressed
F8 : Set up for starting when the F8 key is pressed
SCAN : Set up for starting when the SCAN key is pressed
Gun Trigger : Set up for starting when the Gun Trigger is Pressed
Terminator
Set up the special character to add the output barcode value
Select one of the values below value
None : Do not use the Terminator.
CRLF : Add Carriage Return/Line Feed at the end of the Barcode
value
Space : Add the space at the end of the barcode value
Tab : Add the tap character at the end of the barcode value
Chapter 4. Optional module
42
Result Type
Set output barcode form
Select the type of the one of the following types
Keyboard Event : Output barcode value on the screen by using
Keyboard Event.
Copy and Paste : Copy to clipboard and then copy to screen .
◆
Warning!
Please do not look directly into the laser beam of barcode, or it may do harm to your vision.
Chapter 4. Optional module
43
Barcode scanning
1. Remove the protective film from the window of barcode.
2. Executing the BarcodeDemo program.
3. Emit laser beam to the barcode.
• Adjust the distance according to the size of barcode.
• Barcode will stop automatically in five minutes if out of the Barcode reading range.
[Correct barcode reading]
1. The more small size of barcode, needs the more close to barcode. The effective scanning rang of is from 40 ~ 300mm. if failed to scan barcode, please
try to adjust scan angle and distance.
2. The laser beam is a red thick line, when scanning a barcode.
[Incorrect barcode reading]
1. The laser beam must across the barcode.
2. It will couldn’t scan barcode if the laser beam across only a fraction of barcode.
Chapter 4. Optional module
44
WiFi Power On /Off Wireless Zero Configuration
WiFi is always set to the OFF state, when products ship from factory Customer needs to ON for using WiFi
[Start button] -> [Setting]
-> [System] -> [WiFi POWER]
ON: WiFi ON
OFF: WiFi OFF
When you want to turn off
the WiFi function.
please turn off WiFi
When you want to turn on
the WiFi function.
Please turn on WiFi
Chapter 4. Optional module
45
How to connect AP (1)
When you turn on Wi-Fi, AP list up automatically. .
Chapter 4. Optional module
Choose the AP what you
want to use and click
Click for connecting
Input the network key.
If it connect well you will
be able to see mark as screen
46
How to connect AP (2)
You can connect using the wireless AP management program
[Start button] -> [Setting] -> [Connections] -> [Network cards]
Chapter 4. Optional module
AP or Router captured
automatically, Click on the
appropriate device form the list
Click as picture
Input the Network key
You will be able to see
connect Wireless
47
WiFi Power On /Off Summit client utility
WiFi is always set to the OFF state, when products ship from factory
Customer needs to ON for using WiFi
[Start button] -> [Setting] -> [System] -> [WiFi POWER]
Click WiFi Power Tray Icon
Click on the WiFi
If the summit of the setting
is the only default profile,
SCU will execute automatically
Click the "Scan"
Click the “Yes"
Input the password
Click the “Commit”
If you choose a list of registered
AP WiFi connection,
turn on the WiFi
Chapter 4. Optional module
Click the “Configure"
48
This User Guide described how to Pairing and Disconnecting between AT880 and Bluetooth devices, and also described basic testing method of Mobile Printer SPR-R203,
which launched by Bixolon, as a sample device.
** It could pairing with maximum 6ea devices, but assign COM Port only to COM2 and COM7.
Bluetooth connection and termination
[Start button] -> [Setting] -> [Bluetooth] -> [MODE]
1. Start Bluetooth function
Turn on the “Bluetooth”
: Depends on checking check box user can control the
Bluetooth power.
 Select : Bluetooth On
 No select : Bluetooth Off
Checking
Set up for searching this device by other devices
: Depends on checking check box, user can set up for Bluetooth
 Select: Allow to searching this device by other devices
 No select: Do not allow to searching this device by other devices.
Chapter 4. Optional module
49
Bluetooth Pairing
After connecting each other through pairing way, Bluetooth devices could do its function properly.
[Start button] -> [Setting] -> [Bluetooth] -> [Devices]
Press the ‘Add new device’
for searching devices which could
paring
Chapter 4. Optional module
Choose the devices on searching
list for paring and click the next
Depending on the situation,
maybe need to input password
for some devices, then could
Input the PIN code and click
the next button.
*Basically SPP-R200’s printer
pin code is “0000”.
Click the SPP-R200 on the list
50
Choose the serial port.
“choose the”COM port” tap and
click the new serial port
Click the SPP-R200 on the list.
Choose the communications
Port (COM2), and then click
the finish button.
After that it is possible to transmission
and reception of data by COM2 port
*when you add a new device, the equipment information is not normally displayed
Please try again
* Password that should be used to Pairing (authentication code), the unit can be set by mutual
* After the paring is normally achieved, User can use SDK for Bluetooth service. The SDK should be by manufacture of the Bluetooth devices
Chapter 4. Optional module
51
Bixolon SPP-R200 Printer Demo
SPP-R200 is typical Mobile Printer of the Bixolon, you can using its App which get from Bixolon website to perform print through Bluetooth.
**the Printer program and SDK, which described in this User Guide is based on the 5th Aug, 2011, and it’s would be a little different from homepage contents
according to the Bixolon policy.
1. Download “SPP-R200 Windows SDK” from the Bixolon homepage (www.bixolon.com) to a suitable directory and unzip the file.
2. Bluetooth Power ON.
3. Executing “Bluetooth Device Properties” programs which located in Control Panel.
4. SPP-R200 printer power ON.
5. Setting the SPP-R200 printer to be in the status of pairing. (Please refer to the User Guide of SPP-R200 Printer)
6. Press “Scan Device” button to searching printer device nearby.
7. In the status of pairing, the factory setting password is “0000” usually.
8. If connected successfully, “COM2 port connected” message will be confirmed. (If had connected one time, maybe not show the message.)
9. Copy and paste the DLL and executable file, which located at bin\ce5\MobileCompia_M3Plus\ within the printer SDK, to SI203x Flash Disk.
10. Executing the Sample.exe program in the SI203X Flash Disk.
11. Change the COM8 to COM2, then press “Open” button to testing printer.
12. Please check to click Printing button and sample printing button. it is working well or not
Change from COM8 to COM2
Chapter 4. Optional module
Click Open button and Printing button
Click the Sample Printing button
52
How to use Phone
1. [Home] -> [Phone]
2. [Start Button]->[Phone]
3. Press Keyboard
button.
Dialing
Function Key
Descriptions
Delete number one by one.
Enable add/edit/delete/ speed dial number and make phone call.
(Save maximum 98ea speed dial numbers.)
Enable to looking for recent Call History.
After input phone number, press “Talk” button to dialing.
 Press and hold relevent Speed Dial number for a while to make phone call, when you the speed
dial number has been already registered.
Chapter 4. Optional module
53
Receiving Phone Call
Function Key
Descriptions
Press this button to receive incoming phone call.
Press this button to reject a phone call.
 Received message inforamtion maybe different.
Hang off Phone Call
Function Key
Descriptions
Communicate via Speaking Key.
Mute microphone during a phone call.
Switch active phone call on holding status.
Switch on holding phone call to active status.
Enable to Search/add/delete contacts.
Enable to add a phone call while looking for contacts,
End a phone call.
Chapter 4. Optional module
54
Contact List
1. [Home] -> [Contacts]
How to search a contact information
Enter the contacts number
or name into the searching box.
Chapter 4. Optional module
55
Add to contact list
Press this button to add
a new contact information
Enable to add mobile phone
number.
Chapter 4. Optional module
Select new contact information
type.
Select items which will add
new contact information.
Enable to add name and company
information.
Enable to add new Email
information.
Except for mobile number,
Enable to add other phone number.
Except for basic e-mail address,
enable to add other e-mail information.
56
How to use Text Message
1. [Home] -> [Text Message]
2. [Start Button]->[Text Message]
Sending Message
Press this button
to make a new message.
Chapter 4. Optional module
Press this button
to send a message.
57
Receiving Message
 Received message may expressed differently.
Press this button
to check new message.
Check message in detail.
Click the relevant
message in received
message box.
Press “Reply/Forward(R)” button
and then choose Reply(R) item.
Replying Message
Chapter 4. Optional module
Press this button
to send replly message,
after done text.
58
This product enable to install GPS module and comes out internal type.
GPS program port : GPD1
GPS hardware port : COM6, 9600
GPS demo application execution
[Start Button] -> [DEMO_GPS_WM]
Execute DEMO_GPS_WM
Application.
Main window button description :
Start : press “Start” button to start to receiving GPS data.
Stop : press “Stop” button to stop receiving GPS data.
Confirm GPS receiving Data:
1. GPS data should be received effectively in open field.
2. GPS Data receiving time is depended on actual using environment. (around 3~10minutes)
After received GPS data once, then next GPS connection will be very fast.
Chapter 4. Optional module
59
This product comes out with 3.0 Mega pixel camera with flash and enable to adjust screen brightness, resolution, screenshot capture, and record video and so
on functions.
Use of camera
[Start Button] -> [Pictures&Videos] -> [Camera]
Execute Camera Application.
Main Window button description :
Thumb… : end the main window and switch to Pictures&Videos screen.
Menu : main Manu list
press “Enter” button to save current screen picture.
Chapter 4. Optional module
60
This product comes out with internal type of HF13.56MHz reader as optional item, and card reading distance around 3~8.5cm compliant with ISO
Standards, and in the case of Mifare tag, the reading distance around between 1~3.5cm.
HF13.56 demo application execution
[Start Button] -> [DEMO_HF]
Mifare tag recognition
Mifare:
Open : Open HF device
Close : Close HF device
Antenna : Stop emit antenna power.
Perform : Send command which selected from above combo box.
ISO > : Switch ISO-15693 command screen.
Block : Block number which will be accessed
Key Type : Key type of block which will be accessed.
Key Set : Key set of block which will be accessed.
Chapter 4. Optional module
61
ISO15693 tag recognition
ISO15693:
< MF : switch to Mifare command window.
Block : start number of block which will be accessed.
Read Count : number of block which be accessed.
This product enable to communicate with IC Card which compliant with ISO-7816.
SmartCard demo application execution
[Start Button] -> [DEMO_SAM]
Main window button description :
Slot Status : check card status whether inserted into sloct.
PowerOn : power on IC Card reader module.
PowerOff : power off IC Card reader module.
SetParam : set or change Card reader’s protocol type, clock rate,
bit rate and so on data.
GetParam : get Card reader’s protocol type, clock rate,
bit rate and so on data.
Default : initialize Card reader’s set value to default values.
TxBlock : send APDU Command to Card reader.
FwVersion : get the firmware version of Card reader.
Chapter 4. Optional module
62
This product enable to install UHF module as optional item, and read&write RFID tag based on GEN2, ISO/IEC 18000-6C Protocol,
performance frequency CE 865~868MHz, FCC 902~928MHz
UHF Reader
UHF 900MHz demo application execution
[Start Button] -> [DEMO_UHF]
Demo Main window button description :
Select a tag that will perform “Access” command.
Start : press Start button to perform “Inventory”,
and button changed into “Stop” icon.
Clear : delete all tag values on the screen.
Menu : Main Manu
Chapter 4. Optional module
63
Demo Application optional Manu :
Read/Write : Read/Write tag.
Lock/Kill : Lock/Kill tag.
Option : Application option.
Version : Version infroamtion.
Read/Write window button description :
Mask : if selected a tag value on main window, then the tag value also showed on Read/Write window,
and used as masking pattern while performing Read/Write tag.
It means even there are a great many of tags around the reader,
Read/Write command only apply those tag that set as masking pattern,
Kill Pwd, Access Pwd : Read/Write tag’s Kill password, access
EPC length : Read/Write Tag’s EPC length.
Even though using 128bits tag, but if EPC length set as 96bits,
then only identify 96bits if performance Inventory command.
Please refer to EPC Class1 Gen2 specification for further information.
Read/Write : Read/Write tag to designated Memory Bank.
MemBank : read/write의 target memory bank.
Ptr : Memory Bank offset which would be read/write.
Seconds : read/write time(seconds)
Format : read/write data format.
Chapter 4. Optional module
64
Lock/Kill window button description :
Mask : if selected a tag value on main window, then the tag value also showed on Read/Write
window and used as masking pattern while performing Lock/Kill tag.
It means even there are a great many of tags around the reader,
Lock/Kill tag command only apply those tag that set as masking pattern.
Kill Pwd, Access Pwd : Read/Write tag’s Kill password, access password.
EPC length : Read/Write Tag’s EPC length.
Even though using 128bits tag, but if EPC length set as 96bits,
then only identify 96bits if performance Inventory command.
Please refer to EPC Class1 Gen2 specification for further information.
Do Lock : performance command according to check marks on box.
Kill : Kill tag. The tag will be never restore if kill a tag, please think twice before perform kill tag.
Options Window button description :
Session : change Session when operating Tag.
Target : change target when operating tag.
Q : change Q in Tag operation
LBT Ch State/Time : change LBT option for Europe, Japan type(forbidden)
Power : change Tx Power level of Reader.
Chapter 4. Optional module
65
Version Window button description :
Demo app Ver : Demo application Version.
Firmware Ver : UHF module firmware Version.
Protocol Ver : UHF module library Version.
Hopping Mode : UHF module country Version.
Max Tx Pwr : UHF module maximum output.
Chapter 4. Optional module
66
Appendix
Product specification
PHYSICAL CHARACTERISTICS
Dimensions (L x W x H)
159 x 79 x 27.7 (35.2)mm
Weight
280g (PDA only, without battery)
Operating Temp.
-20℃ ~ 60℃
Storage Temp.
-30℃ ~ 70℃
Humidity
95% non-condensing
Drop Spec.
1.5M Drop to concrete
Dust & Water Proof
IP65
PERFORMANCE CHARACTERISTICS
Processor
Marvell™ PXA320 806MHz
Operating System
Windows CE 5.0 / Windows Embedded handheld 6.5 (Option)
Memory
256MB (512MB Option) RAM / 512MB ROM
Display
3.5” QVGA with Backlight, TFT LCD, 240 x 320Pixel, 262K Color
Audio
Phone Receiver, Speaker, Ear Jack, Microphone
Standard I/O Port
USB 1.1 Client / USB Host & Serial (RS-232) via gender cable or Cradle
Expansion Slot
1Micro SD Slot (SDHC), 1SIM Slot, 1SAM Slot
Notification
Vibrator and LED, Speaker
BATTERY SUPPLY
Main Battery
Lithium Polymer 3.7V 2,970mAh (Rechargeable)
Backup Battery
Lithium Polymer 3.7V 80mAh (Rechargeable)
Power Adapter
Input AC100V ~ 240V / Output DC 5V 3A
Chapter 5. Appendix
67
NETWORK CHARACTERISTICS
WLAN
IEEE 802.11 a/b/g Compliant (a/b/g/n Option)
Bluetooth
Bluetooth Class II, 2.1 + EDR
Radio
MODEM 3G (GSM / GPRS / EDGE / WCDMA / HSPA+)
GPS
Internal Antenna (GPS + Glonass Option)
DATA CAPTURE & DATA PROCESSING DEVICE
Barcode Engine
1D Laser or 2D Imager Barcode Scanner (2D Long Range Barcode Option)
Camera
3.0 Mega Pixel Auto Focus with Flash
UHF 900MHZ RFID READER/WRITER
Frequency
CE 865MHz ~ 868MHz
FCC 902MHz ~ 928MHz
Reading range
0M ~ 5M (According to Tag & Environment)
Writing range
0M ~ 0.5M (According to Tag & Environment)
RF output
1W (MAX)
Protocol
GEN2, ISO/IEC 18000-6C
Special function
Anti-Collision
HF 13.56MHZ RFID READER/WRITER
Applied RFID Tag
ISO15693, MIFARE, ISO14443 A/B (Option)
Reading range
According to Tag : 0Cm ~ 5Cm (Internal or External)
ACCESSORIES(OPTION)
Gun Handle Grip (Pistol Grip)
Body, UHF / HF Available
Gun Handle Battery
Lithium-Ion 3.7V 5,200mAh (Rechargeable) Option
* All Features and specifications described are subject to change without notice.
Chapter 5. Appendix
68