United Kingdom
en
Installation and Service Manual
Gas Fired Wall Mounted Condensing Combination Boiler
EcoBlue Advance Combi
24 - 28 - 33 - 40
These instructions include the Benchmark Commissioning Checklist and should be left with the
user for safe keeping. They must be read in conjunction with the Flue Installation Guide.
Model Range
Building Regulations and the Benchmark Commissioning
Checklist
Baxi EcoBlue Advance 24 Combi ErPD
G.C.No 47-077-14
Baxi EcoBlue Advance 28 Combi ErPD
G.C.No 47-077-15
Baxi EcoBlue Advance 33 Combi ErPD
G.C.No 47-077-16
Baxi EcoBlue Advance 40 Combi ErPD
G.C.No 47-077-17
Building Regulations (England & Wales) require notification of the
installation of a heating appliance to the relevant Local Authority
Building Control Department. This can be achieved via a
Competent Persons Self Certification Scheme as an option to
notifying the Local Authority directly.
The Health & Safety Executive operates the ‘Gas Safe Register’, a selfcertification scheme for gas heating appliances.
This company is a member of the Benchmark initiative and fully
supports the aims of the programme. Its aim is to improve the
standards of installation and commissioning of central heating systems
in the UK and to encourage the regular servicing of all central heating
systems to ensure safety and efficiency.
Building Regulations require that installations should comply with
manufacturer's instructions. It is therefore important that the
commissioning checklist is completed by the installer. The relevant
section of Building Regulations only relates to dwellings. Therefore the
checklist only applies if the appliance is being installed in a dwelling or
some related structure.
The flowchart opposite gives guidance for installers on the process
necessary to ensure compliance with Building Regulations.
0086
ISO 9001
FM 00866
The Benchmark Scheme
Benchmark places responsibilities on both manufacturers and installers.
The purpose is to ensure that customers are provided with the correct
equipment for their needs, that it is installed, commissioned and
serviced in accordance with the manufacturer’s instructions by
competent persons and that it meets the requirements of the
appropriate Building Regulations. The Benchmark Checklist can be
used to demonstrate compliance with Building Regulations and should
be provided to the customer for future reference.
Installers are required to carry out installation, commissioning and
servicing work in accordance with the Benchmark Code of Practice
which is available from the Heating and Hotwater Industry Council who
manage and promote the Scheme. Visit www.centralheating.co.uk for
more information.
© Baxi Heating UK Ltd 2017 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, or
stored in any retrieval system of any nature (including in any database), in each case whether electronic, mechanical, recording or otherwise,
without the prior written permission of the copyright owner, except for permitted fair dealing under Copyrights, Designs and Patents Act 1988.
Applications for the copyright owner’s permission to reproduce or make other use of any part of this publication should be made, giving details of
the proposed use, to the following address:
The Company Secretary, Baxi Heating UK Limited, Brooks House, Coventry Road, Warwick. CV34 4LL
Full acknowledgement of author and source must be given.
WARNING: Any person who does any unauthorised act in relation to a copyright work may be liable to criminal prosecution and civil claims for
damages.
You have just purchased one of our appliances and we thank you for the trust you have placed in our products. Please note that
the product will provide good service for a longer period of time if it is regularly checked and maintained. Our customer support
network is at your disposal at all times.
2
EcoBlue Advance Combi
7219715 - 03 (04/17)
Installer Notification Guidelines
Installer Notification Guidelines
Choose Building
Regulations Notification
Route
Competent Person's
Self Certification Scheme
Building Control
Install and Commission this
appliance to manufacturer's
instructions
Contact your relevant Local
Authority Building Control
(LABC) who will arrange
an inspection or contact
a government approved
inspector
Complete the
Benchmark Checklist
If you notify via the ‘Gas Safe
Register’, the register will issue
the Building Regulations
certificate on members’ behalf
Install and Commission this
appliance to manufacturer's
instructions
Scheme Members only
Call ‘Gas Safe Register’ on:
0800 408 5577
or log onto:
www.gassaferegister.co.uk
within 10 days
Complete the
Benchmark Checklist
You must ensure that the
certificate number issued by
the ‘Gas Safe Register’ is written
onto the Benchmark Checklist
‘Gas Safe Register’ will issue a
Building Regulations Compliance
Certificate to the property owner
and inform the relevant LABC
7219715 - 02 (09/16)
LABC will record the data
and will issue a
certificate of compliance
EcoBlue Advance Combi
3
Contents
Contents
1
Introduction
1.1
1.2
1.3
1.4
1.5
1.6
2
Safety
2.1
2.2
2.3
3
4
7
7
8
8
9
9
10
10
10
11
12
General Safety Instructions
Recommendations
Specific Safety Instructions
2.3.1
Handling
12
12
13
13
14
3.1
3.2
3.3
3.4
14
15
16
17
Technical Data
Technical Parameters
Dimensions and Connections
Electrical Diagram
Description of the Product
18
4.1
4.2
18
19
19
19
19
19
20
21
22
22
22
General Description
Operating Principle
4.2.1
Central Heating Mode
4.2.2
Domestic Hot Water Mode
4.2.3
Boiler Frost Protection Mode
4.2.4
Pump Protection
Main Components
Control Panel Description
Standard Delivery
Accessories & Options
4.6.1
Optional Extras
Before Installation
23
5.1
5.2
23
24
24
24
24
24
24
25
25
25
26
27
27
27
27
27
28
30
31
33
5.3
4
7
Technical Specifications
4.3
4.4
4.5
4.6
5
General
Additional Documentation
Symbols Used
Abbreviations
Extent of Liabilities
1.5.1
Manufacturer’s Liability
1.5.2
Installer’s Responsibility
Homologations
1.6.1
CE Marking
1.6.2
Standards
Installation Regulations
Installation Requirements
5.2.1
Gas Supply
5.2.2
Electrical Supply
5.2.3
Hard Water Areas
5.2.4
Bypass
5.2.5
System Control
5.2.6
Treatment of Water Circulating Systems
5.2.7
Showers
5.2.8
Expansion Vessel (CH only)
5.2.9
Safety Pressure Relief Valve
Choice of the Location
5.3.1
Location of the Appliance
5.3.2
Data Plate
5.3.3
Bath & Shower Rooms
5.3.4
Ventilation
5.3.5
Condensate Drain
5.3.6
Clearances
5.3.7
Flue/Chimney Location
5.3.8
Horizontal Flue/Chimney Systems
EcoBlue Advance Combi
7219715 - 03 (04/17)
Contents
5.4
5.5
5.6
6
Installation
37
6.1
6.2
37
37
37
38
38
38
39
39
41
41
41
41
42
42
42
6.3
6.4
6.5
6.6
6.7
7
43
7.1
7.2
43
43
43
43
44
44
44
44
46
46
46
46
47
7.4
7.5
7.6
9
General
Assembly
6.2.1
Fitting the Pressure Relief Discharge Pipe
6.2.2
Connecting the Condensate Drain
Preparation
6.3.1
Panel Removal
Air Supply / Flue Gas Connections
6.4.1
Connecting the Flue/Chimney
Electrical Connections
6.5.1
Electrical Connections of the Appliance
6.5.2
Connecting External Devices
Filling the Installation
External Controls
6.7.1
Installation of External Sensors
6.7.2
Optional Outdoor Sensor
Commissioning
7.3
8
34
34
34
34
34
34
35
35
35
35
36
36
36
5.3.9
Flue/Chimney Lengths
5.3.10 Flue/Chimney Trim
5.3.11
Terminal Guard
5.3.12 Flue/Chimney Deflector
5.3.13 Flue/Chimney Accessories
Transport
Unpacking & Initial Preparation
5.5.1
Unpacking
5.5.2
Initial Preparation
5.5.3
Flushing
Connecting Diagrams
5.6.1
System Filling and Pressurising
5.6.2
Domestic Hot Water Circuit
General
Checklist before Commissioning
7.2.1
Preliminary Electrical Checks
7.2.2
Checks
Commissioning Procedure
7.3.1
De-Aeration Function
Gas Settings
7.4.1
Check Combustion - ‘Chimney Sweep’ Mode
Configuring the System
7.5.1
Check the Operational (Working Gas Inlet Pressure & Gas Rate)
Final Instructions
7.6.1
Handover
7.6.2
System Draining
Operation
48
8.1
8.2
8.3
8.4
8.5
48
48
48
49
49
General
To Start-Up
To Shutdown
Use of the Control Panel
Frost Protection
Settings
9.1
7219715 - 03 (04/17)
50
50
Parameters
EcoBlue Advance Combi
5
Contents
10
11
12
13
14
6
Maintenance
51
10.1
10.2
10.3
51
52
53
53
54
54
55
55
56
56
56
56
56
57
57
57
58
58
59
59
60
60
60
61
61
62
62
63
General
Standard Inspection & Maintenance Operation
Specific Maintenance Operations Changing Components
10.3.1 Spark Ignition & Flame Sensing Electrodes
10.3.2 Fan
10.3.3 Air / Gas Venturi
10.3.4 Burner
10.3.5 Insulation
10.3.6 Flue Sensor
10.3.7 Igniter
10.3.8 Heating Flow & Return Sensors
10.3.9 Safety Thermostat
10.3.10 DHW NTC Sensor
10.3.11 Pump - Head Only
10.3.12 Pump - Complete
10.3.13 Automatic Air Vent
10.3.14 Safety Pressure Relief Valve
10.3.15 Heating Pressure Gauge
10.3.16 Plate Heat Exchanger
10.3.17 Hydraulic Pressure Sensor
10.3.18 DHW Flow Regulator & Filter
10.3.19 DHW Flow Sensor (‘Hall Effect’ Sensor)
10.3.20 Diverter Valve Motor
10.3.21 Main P.C.B.
10.3.22 Boiler Control P.C.B.
10.3.23 Expansion Vessel
10.3.24 Gas Valve
10.3.25 Setting the Gas Valve (CO2 Check)
Troubleshooting
64
11.1
11.2
64
64
Error Codes
Fault Finding
Decommissioning Procedure
70
12.1
70
Decommissioning Procedure
Spare Parts
71
13.1
13.2
71
71
General
Spare Parts List
Notes
72
Benchmark Commissioning Checklist
74
EcoBlue Advance Combi
7219715 - 03 (04/17)
Introduction
1
1
Introduction
1.1
Warning
This boiler can be used by children aged 8 years and
above and by persons with reduced physical, sensory
or mental capabilities or lack of experience and
knowledge when they have been given supervision or
instruction concerning the safe use of the device and
understand the resulting risks. Children must not be
allowed to play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision.
General
WARNING
Installation, repair and maintenance must only be
carried out only by a competent person. This
document is intended for use by competent persons.
All Gas Safe registered engineers carry an ID card with their
licence number and a photograph. You can check your engineer
is registered by telephoning 0800 408 5500 or online at
www.gassaferegister.co.uk
This appliance must be installed in accordance with the
manufacturer’s instructions and the regulations in force. If the
appliance is sold or transferred, or if the owner moves leaving
the appliance behind you should ensure that the manual is kept
with the appliance for consultation by the new owner and their
installer. Read the instructions fully before installing or using the
appliance.
In GB, this must be carried out by a competent person as stated
in the Gas Safety (Installation & Use) Regulations (as may be
amended from time to time).
Definition of competence: A person who works for a Gas Safe
registered company and holding current certificates in the
relevant ACS modules, is deemed competent.
In IE, this must be carried out by a competent person as stated
in I.S. 813 “Domestic Gas Installations”.
The addition of anything that may interfere with the normal
operation of the appliance without express written permission
from the manufacturer or his agent could invalidate the
appliance warranty. In GB this could also infringe the Gas Safety
(Installation and Use) Regulations.
The appliance is designed as a boiler for use in residential
domestic environments on a governed meter supply only. The
selection of this boiler is entirely at the owner’s risk. If the
appliance is used for purposes other than or in excess of these
specifications, the manufacturer will not accept any liability for
resulting loss, damage or injury.
The manufacturer will not accept any liability whatsoever
for loss, damage or injury arising as a result of failure to
observe the instructions for use, maintenance and
installation of the appliance.
WARNING
Check the information on the data plate is
compatible with local supply conditions.
1.2
Additional Documentation
These Installation & Service Instructions must be read in
conjunction with the Flue Installation Guide supplied in the
Literature Pack.
Various timers, external controls, etc. are available as optional
extras. Full details are contained in the relevant sales literature.
7219715 - 03 (04/17)
EcoBlue Advance Combi
7
1
Introduction
1.3
Symbols Used
In these instructions, various levels are employed to draw the
user's attention to particular information. In so doing, we wish to
safeguard the user's safety, prevent hazards and guarantee
correct operation of the appliance. Each level is accompanied by
a warning triangle
DANGER
Risk of a dangerous situation causing serious
physical injury.
WARNING
Risk of a dangerous situation causing slight physical
injury.
CAUTION
Risk of material damage.
Signals important information .
Signals a referral to other instructions or other pages
in the instructions.
1.4
Abbreviations
DHW: Domestic hot water
CH: Central heating
GB: Great Britain
IE: Ireland
BS: British standard
HHIC: Heating and Hotwater Industry Council
Pn: Nominal output
Pnc: Condensing output
Qn: Nominal heat input
Qnw: Nominal domestic hot water heat input
Hs: Gross calorific value
8
EcoBlue Advance Combi
7219715 - 03 (04/17)
Introduction
1.5
1.5.1
1
Extent of Liabilities
Manufacturer's Liability
Our products are manufactured in compliance with the
requirements of the various european applicable Directives.
They are therefore delivered with
marking and all relevant
documentation. In the interest of customers, we are
continuously endeavouring to make improvements in product
quality. All the specifications stated in this document are
therefore subject to change without notice.
The manufacturer will not accept any liability for loss, damage or
injury arising as a result of:Failure to abide by the instructions on using the appliance.
Failure to regularly maintain the appliance, or faulty or
inadequate maintenance of the appliance.
Failure to abide by the instructions on installing the
appliance.
This company declares that no substances harmful to
health are contained in the appliance or used during
appliance manufacture.
The appliance is suitable only for installation in GB and IE and
should be installed in accordance with the rules in force, and
only used in a suitably ventilated location.
In GB, the installation must be carried out by a Gas Safe
Registered Installer. It must be carried out in accordance with
the current and relevant requirements of legislation and
guidance including the:• Gas Safety (Installation & Use) Regulations.
• The appropriate Building Regulations either The
Building Regulations, The Building Regulations
(Scotland), Building Regulations (Northern Ireland).
• The Water Fittings Regulations or Water Byelaws in
Scotland.
• The Current I.E.E. Wiring Regulations.
Where no specific instructions are given, reference should be
made to the relevant British Standard Code of Practice.
In IE, the installation must be carried out by a competent person
and installed in accordance with the current edition of I.S. 813
‘Domestic Gas Installations’, the current Building Regulations
and reference should be made to the current ETCI rules for
electrical installation.
Prior to commissioning all systems must be thoroughly
flushed and treated with inhibitor (see section 5.2.6). Failure
to do so will invalidate the appliance warranty.
Incorrect installation could invalidate the warranty and may lead
to prosecution.
7219715 - 03 (04/17)
EcoBlue Advance Combi
9
1
Introduction
1.5.2
Installer's Responsibility
The installer is responsible for the installation and initial start up
of the appliance. The installer must adhere to the following
instructions:
Read and follow the instructions given in the manuals
provided with the appliance.
Carry out installation in compliance with the prevailing
legislation and standards.
Ensure the system is flushed and inhibitor added.
Install the flue/chimney system correctly ensuring it is
operational and complies with prevailing legislation and
standards, regardless of location of the boiler’s installation.
Only the installer should perform the initial start up and carry
out any checks necessary.
Explain the installation to the user.
Complete the Benchmark Commissioning Checklist - this is a
condition of the warranty !
Warn the user of the obligation to check the appliance and
maintain it in good working order.
Give all the instruction manuals to the user.
1.6
Homologations
1.6.1
CE Marking
EC - Declaration of Conformity
Baxi Heating UK Limited being the manufacturer / distributor
within the European Economic Area of the following:Baxi EcoBlue Advance 24 - 28 - 33 - 40 Combi ErPD
declare that the above is in conformity with the provisions of the
Council Directive
2009/142/EC 92/42/EEC 2004/108/EC 2006/95/EC
2009/125/EC 2010/30/EU
and has been subject to the following conformity procedures laid
down in
Annex 2 - Article 3 of 2009/142/EC
under the supervision of the British Standards Institution, a
Notified Body authorized by the United Kingdom Competent
Authority, and carrying the Notified Body Number 0086.
Type test for purpose of Regulation 5 certified by:
Notified Body 0085.
Product/Production certified by:
Notified Body 0086.
For GB/IE only.
10
EcoBlue Advance Combi
7219715 - 03 (04/17)
Introduction
1.6.2
1
Standards
Codes of Practice - refer to the most recent version
In GB the following Codes of Practice apply:
Standard
Scope
BS 6891
Gas Installation.
BS 5546
Installation of hot water supplies for domestic
purposes.
BS EN 12828
Heating systems in buildings.
BS EN 12831
Heating systems in buildings - Calculation of
load.
BS EN 14336
Installation & commissioning of water based
heating systems.
BS 6798
Installation of gas fired hot water boilers.
BS 5440 Part 1 Flues.
BS 5440 Part 2 Ventilation.
BS 7074
Expansion vessels and ancillary equipment for
sealed water systems.
BS 7593
Treatment of water in domestic hot water
central heating systems.
BS 4814
Specification for Expansion Vessels using an
internal diaphragm, for sealed hot water
systems.
IGE/UP/7/1998 Guide for gas installations in timber framed
housing.
In IE the following Codes of Practice apply:
Standard
Scope
I.S. 813
Domestic Gas Installations.
The following standards give valuable additional information;
BS 5546
Installation of hot water supplies for domestic
purposes.
BS EN 12828
Heating systems in buildings.
BS EN 12831
Heating systems in buildings - Calculation of
load.
BS EN 14336
Installation & commissioning of water based
heating systems.
BS 7074
Expansion vessels and ancillary equipment for
sealed water systems.
BS 7593
Treatment of water in domestic hot water
central heating systems.
7219715 - 03 (04/17)
EcoBlue Advance Combi
11
2
2
Safety
Safety
2.1
General Safety Instructions
DANGER
If you smell gas:
1. Turn off the gas supply at the meter
2. Open windows and doors in the hazardous area
3. Do not operate light switches
4. Do not operate any electrical equipment
5. Do not use a telephone in the hazardous area
6. Extinguish any naked flame and do not smoke
7. Warn any other occupants and vacate the
premises
8. Telephone the National Gas Emergency Service
on:- 0800 111 999
2.2
Recommendations
WARNING
Installation, repair and maintenance must be carried
out by a Gas Safe Registered Engineer
(in accordance with prevailing local and national
regulations).
When working on the boiler, always disconnect the
boiler from the mains and close the main gas inlet
valve.
After maintenance or repair work, check the
installation to ensure that there are no leaks.
CAUTION
The boiler should be protected from frost.
Only remove the casing for maintenance and repair
operations. Replace the casing after maintenance
and repair operations.
12
EcoBlue Advance Combi
7219715 - 03 (04/17)
Safety
2.3
2.3.1
2
Specific Safety Instructions
Handling
General
•
The following advice should be adhered to, from when first
handling the boiler to the final stages of installation, and
also during maintenance.
•
Most injuries as a result of inappropriate handling and lifting
are to the back, but all other parts of the body are
vulnerable, particularly shoulders, arms and hands. Health
& Safety is the responsibility of EVERYONE.
•
There is no ‘safe’ limit for one man - each person has
different capabilities. The boiler should be handled and lifted
by TWO PEOPLE.
•
Do not handle or lift unless you feel physically able.
•
Wear appropriate Personal Protection Equipment
e.g. protective gloves, safety footwear etc.
Preparation
•
Co-ordinate movements - know where, and when, you are
both going.
•
Minimise the number of times needed to move the boiler plan ahead.
•
Always ensure when handling or lifting the route is clear
and unobstructed. If possible avoid steps, wet or slippery
surfaces, unlit areas etc. and take special care on
ladders/into lofts.
Technique
•
When handling or lifting always use safe techniques - keep
your back straight, bend your knees. Don’t twist - move your
feet, avoid bending forwards and sideways and keep the
load as close to your body as possible.
•
Where possible transport the boiler using a sack truck or
other suitable trolley.
•
Always grip the boiler firmly, and before lifting feel where the
weight is concentrated to establish the centre of gravity,
repositioning yourself as necessary. See the ‘Installation’
section of these instructions for recommended lift points.
Remember
•
The circumstances of each installation are different. Always
assess the risks associated with handling and lifting
according to the individual conditions.
•
If at any time when installing the boiler you feel that you
may have injured yourself STOP !! DO NOT ‘work through’
the pain - you may cause further injury.
IF IN ANY DOUBT DO NOT HANDLE OR LIFT THE BOILER OBTAIN ADVICE OR ASSISTANCE BEFORE PROCEEDING !
7219715 - 03 (04/17)
EcoBlue Advance Combi
13
3
Technical Specifications
3
Technical Specifications
3.1
Appliance Type
Electrical Supply
230V~ 50Hz
(Appliance must be connected to an
earthed supply)
C13 C33 C53
Appliance Category
CAT I 2H
Heat Input CH Qn Hs (Gross)
Max
24 model
kW
22.2
28 model
kW
26.6
33 model
kW
31.1
40 model
kW
35.5
Min
5.2
6.3
7.6
8.9
Heat Output CH Pn (Non-Condensing)
Max
Min
24 model
kW
20.0
4.6
28 model
kW
24.0
5.5
33 model
kW
28.0
6.6
40 model
kW
32.0
7.8
Heat Output CH Pnc (Condensing)
Max
Min
24 model
kW
21.2
4.9
28 model
kW
25.3
6.0
33 model
kW
29.6
7.1
40 model
kW
33.9
8.4
Heat Input DHW Qnw Hs (Gross)
Max
24 model
kW
27.4
28 model
kW
32.1
33 model
kW
37.8
40 model
kW
45.8
Heat Output DHW
24 model
28 model
33 model
40 model
kW
kW
kW
kW
Gas Nozzle Injector
24 model
mm
28 model
mm
33 model
mm
40 model
mm
NOx Class
Technical Data
Max
24.0
28.0
33.0
40.0
Ø 5.0
Ø 5.6
Ø 6.6
Ø 6.6
5
Temperatures
C.H. Flow Temp (adjustable)
25°C to 80°C max (± 5°C)
D.H.W. Flow Temp (adjustable)
40°C to 60°C max (± 5°C)
dependent upon flow rate
Power Consumption
24 model
W
28 model
W
33 model
W
40 model
W
Safety Discharge
Max Operating
Min Operating
Recommended Operating Range
85
90
95
100
Electrical Protection
IPX5D (without integral timer)
IP20 (with integral timer)
External Fuse Rating
3A
Flow Rates
Internal Fuse Rating
F2L
DHW Flow Rate
@ 30o C Rise
10.9 12.9
15.3
18.3
DHW Flow Rate
@ 35o C Rise
9.8
11.5
13.5
16.4
Min Working
DHW Flow Rate
2
2
2
2
Condensate Drain
To accept 21.5mm (3/4 in) plastic waste pipe
Flue Terminal
Dimensions
Diameter
Projection
Connections
Gas Inlet
Heating Flow
Heating Return
Cold Water Inlet
Hot Water Outlet
Pressure Relief Discharge
-
100mm
125mm
copper tails
22mm
22mm
22mm
15mm
15mm
15mm
Outercase Dimensions
Casing Height
Overall Height Inc Flue Elbow
Casing Width
Casing Depth
Clearances
Above Casing
Below Casing
Front
Front
L.H. Side
R.H. Side
-
*This is MINIMUM recommended dimension.
Greater clearance will aid installation and
maintenance.
NOTE: All data in this section are nominal
values and subject to normal production
tolerances.
Pump
Available Head
Packaged Boiler Carton
Installation Lift Weight
bar
8
0.15
(24) (28) (33) (40)
l/min l/min l/min l/min
Where Low Flow Taps or Fittings are intended to
be used in the DHW system connected to a Baxi
EcoBlue Advance Combi it is strongly
recommended that the DHW flow rate DOES
NOT fall below 2.5 l/min. This will ensure
reliable operation of the DHW function.
Expansion Vessel - (For Central Heating
only. Integral with appliance)
bar
Min Pre-charge Pressure 1.0
(24 & 28) (33 & 40)
litre
litre
Max Capacity of
CH System
125
155
Primary Water Content
of Boiler (unpressurised) 2.5
2.5
NATURAL GAS ONLY !
Max Gas Rate (Natural Gas - G20)
(After 10 mins)
24 model
m3/h
2.61
28 model
m3/h
3.05
33 model
m3/h
3.59
40 model
m3/h
4.35
Dynamic (nominal) Inlet Pressure
(Natural Gas - G20)
mbar
20
with a CV of 37.78 MJ/m3
See graph below
Product Characteristics Database
(SEDBUK)
6
5.5
5
SAP 2009 Annual Efficiency is
89%
4.5
4
3.5
This value is used in the UK Government’s
3
Metre (wg)
Packaged Boiler Carton
Installation Lift Weight
763mm
923mm
450mm
345mm
175 mm Min
150 mm* Min
450 mm Min (For Servicing)
5 mm Min (In Operation)
5 mm Min
5 mm Min
Pump - Available Head
Packaged Boiler Carton
Installation Lift Weight
bar
3
2.5
0.5
1-2
DHW Circuit
Pressures
Max Operating
Min Operating
Weights
(24/28 model)
42.3kg
36kg
(33 model)
44.3kg
38kg
(40 model)
45.3kg
39kg
Central Heating Primary Circuit
Pressures
2.5
Standard Assessment Procedure (SAP) for energy
2
1.5
rating of dwellings. The test data from which it has
1
0.5
been calculated has been certified by 0085.
0
0
200
400
600
800
1000
1200
Flow Rate (l/h)
14
EcoBlue Advance Combi
7219715 - 03 (04/17)
Technical Specifications
3.2
3
Technical Parameters
Technical parameters for boiler combination heaters
Baxi EcoBlue Advance Combi ErPD
24
28
33
40
Condensing boiler
Yes
Yes
Yes
Yes
Low-temperature boiler(1)
No
No
No
No
B1 boiler
No
No
No
No
Cogeneration space heater
No
No
No
No
Yes
Yes
Yes
Yes
Combination heater
Prated
kW
20
24
28
32
Useful heat output at rated heat output
and high temperature regime(2)
P4
kW
20.0
24.0
28.0
32.0
Useful heat output at 30% of rated heat
output and low temperature regime(1)
P1
kW
6.7
8.0
9.4
10.7
Seasonal space heating energy efficiency Šs
%
93
93
93
93
Useful efficiency at rated heat output and Š4
high temperature regime(2)
%
88.0
87.9
88.0
87.9
Š1
%
98.0
98.0
98.1
98.0
Full load
elmax
kW
0.030
0.035
0.040
0.040
Part load
elmin
kW
0.014
0.014
0.014
0.014
Standby mode
PSB
kW
0.003
0.003
0.003
0.003
Standby heat loss
Pstby
kW
0.035
0.035
0.040
0.045
Ignition burner power consumption
Pign
kW
-
-
-
-
Annual energy consumption
QHE
kWh
GJ
17204
62
20645
74
24086
87
27527
99
Sound power level, indoors
LWA
dB
51
52
53
55
Emissions of nitrogen oxides
NOX
mg/kWh
22
20
24
24
XL
XL
XXL
XXL
Rated heat output
Useful efficiency at 30% of rated heat
output and low temperature regime(1)
Auxiliary electricity consumption
Other items
Domestic hot water parameters
Declared load profile
Daily electricity consumption
Qelec
kWh
0.151
0.168
0.215
0.172
Annual electricity consumption
AEC
kWh
33
37
47
38
Water heating energy efficiency
Šwh
%
90
88
86
85
Daily fuel consumption
Qfuel
kWh
21.340
21.980
27.850
28.570
Annual fuel consumption
AFC
GJ
16
17
22
23
(1) Low temperature means for condensing boilers 30°C, for low temperature boilers 37°C and for other heaters 50°C
return temperature (at heater inlet).
(2) High temperature regime means 60°C return temperature at heater inlet and 80°C feed temperature at heater outlet.
See
The back cover for contact details.
7219715 - 03 (04/17)
EcoBlue Advance Combi
15
3
Technical Specifications
3.3
Dimensions and Connections
There must be no part of the air duct
(white tube) visible outside the property.
Dimensions
At least 1.5°
G
E
A 763mm
B 345mm
C 450mm
A
D 116mm Ø Min.
E 160mm
(207mm for 80/125mm
flue systems)
F 140mm
B
G 106mm
360° Orientation
H 170mm
J 280mm
H
D
C
J
Flue Ø 100mm
Tap Rail
F
Condensate
Drain
50 mm 45 mm
Pressure
Relief
Valve
(15mm)
65 mm
Heating
Flow
(22mm)
16
EcoBlue Advance Combi
65 mm
Hot Water
Outlet
(15mm)
65 mm
Gas
Inlet
(22mm)
65 mm
Cold Water
Inlet
(15mm)
30
95 mm
Heating
Return
(22mm)
7219715 - 03 (04/17)
Technical Specifications
3.4
M2
Low Voltage
External Control
Connection 9
7
8
6
5
4
3
2
3
Electrical Diagram
r
1
bk
w
10
Boiler
Controls
br
R
/R
/P
+
+
bk
Hall Effect
Sensor
g/y
b
DHW
NTC
Sensor
p
b
r
y
w
g
b
br
br
Pump
g
Flue
Sensor
b
b
bk
X20
X21
X40
X30
X41
r
X42
X60
g
Hydraulic
Pressure
Switch
X22
X23
X50
Heating
Return
Sensor
br
b
b
b
Heating
Flow
Sensor
X1 X2
r
X10
X11
b
X13
Igniter
br
b
bk
g
bk
b
b
br
b
br
b
b
Safety
Thermostat
w
NL
bk
Mains Input Cable
br
g/y
bk
br
g
bk
Diverter
Valve
Motor
Fan
g
br
2
3
4
g/y
g/y
Gas
Valve
b
1
b
g/y
b
Timer Connector
Spark
Ignition
Electrode
Flame
Sensing
Electrode
r
br
E
X14
g/y
2
Link
y
g/y
X12
r
M1
Mains Voltage
Connection
1
b
br
5
Timer Bridge
Key To Wiring Colours
7219715 - 03 (04/17)
b
- Blue
r
- Red
bk
- Black
g
- Green
br
- Brown
g/y - Green/Yellow
w
- White
y
- Yellow
gr
- Grey
p
- Purple
EcoBlue Advance Combi
17
4
Description of the Product
4
Description of the Product
4.1
General Description
1. The Baxi EcoBlue Advance Combi boilers are fully automatic
gas fired wall mounted condensing combination boilers. They
are room sealed and fan assisted, and will serve central heating
and mains fed domestic hot water.
2. The boiler is set to give a maximum output of :24 model 28 model 33 model -
Information
Label
40 model -
24 kW DHW
21.2 kW CH Pnc (Condensing)
28 kW DHW
25.3 kW CH Pnc (Condensing)
33 kW DHW
29.6 kW CH Pnc (Condensing)
40 kW DHW
33.8 kW CH Pnc (Condensing)
3. The boiler is factory set for use on Natural Gas (G20).
4. The boiler is suitable for use only on fully pumped sealed
heating systems. Priority is given to domestic hot water.
Boiler Control
Flap
Fig. 1
5. The boiler data badge gives details of the model, serial
number and Gas Council number and is situated on the boiler
lower panel. It is visible when the control box is lowered (Fig. 2).
6. The boiler model, serial number and Gas Council number are
also shown on the information label behind the boiler control flap
(Fig. 1). This is for user reference.
7. The boiler is intended to be installed in residential/domestic
environments on a governed meter supply only.
8. The boiler must be installed with one of the purpose designed
flues such as one of the standard horizontal telescopic flue kits
detailed in the Flue Installation Guide.
All systems must be thoroughly cleansed, flushed and
treated with inhibitor (see section 5.2.6).
These Installation & Servicing Instructions MUST be
read in conjunction with the Flue Installation Guide supplied in
the Literature Pack.
Data Badge
Fig. 2
Control Box
removed for clarity
18
EcoBlue Advance Combi
7219715 - 03 (04/17)
Description of the Product
15
4.2
Operating Principle
The boiler can be set in 3 operating modes:- ‘Summer’
(DHW only), ‘Winter’ (CH & DHW) or ‘Heating Only’ (CH only) by
use of the
button.
16
14
4
4.2.1
Central Heating Mode
17
1. With a demand for heating, the pump circulates water through
the primary circuit.
18
2. Once the burner ignites the fan speed controls the gas rate to
maintain the heating temperature measured by the temperature
sensor.
19
20
3. When the flow temperature exceeds the setting temperature,
a 3 minute delay occurs before the burner relights automatically
(anti-cycling). The pump continues to run during this period.
21
22
4. When the demand is satisfied the burner is extinguished and
the pump continues to run for a period of 3 minutes (pump
overrun).
24
23
13
4.2.2
12
Domestic Hot Water Mode
1. Priority is given to the domestic hot water supply. A demand
at a tap or shower will override any central heating requirement.
11
2. The flow of water will operate the DHW Sensor (Hall Effect
Sensor) which requests the 3 way valve to change position. This
will allow the pump to circulate the primary water through the
DHW plate heat exchanger.
10
3
1
2
5
7
3. The burner will light automatically and the temperature of the
domestic hot water is controlled by the temperature sensor.
6
4. When the domestic hot water demand ceases the burner will
extinguish and the diverter valve will remain in the domestic hot
water mode, unless there is a demand for central heating.
4
8
9
A
B
C
E
D
F
Boiler Schematic
Layout
Key
1. Pump with Automatic Air Vent
2. Boiler Drain Tap
3. Pressure Gauge
4. Safety Pressure Relief Valve
5. DHW Flow Sensor/Filter/Restrictor
6. Domestic Hot Water Priority Sensor
(‘Hall Effect’ Sensor)
7. Domestic Hot Water NTC Sensor
8. Hydraulic Pressure Switch
9. Three Way Valve & Motor
10. Plate Heat Exchanger
11. Gas Valve
12. Safety Thermostat (105° C)
13. Heating Flow Sensor
14. Flue Sensor
15. Boiler Adaptor
16. Primary Heat Exchanger
17. Spark Ignition Electrode
18. Burner
19. Flame Sensing Electrode
20. Air/Gas Collector
21. Heating Return Sensor
22. Fan
23. Air/Gas Venturi
24. Expansion Vessel
Connections:A – Condensate Drain
B – Heating Flow
C – Domestic Hot Water Outlet
D – Gas Inlet
E – Cold Water Inlet On/Off Valve and filter
F – Heating Return
7219715 - 03 (04/17)
4.2.3
Boiler Frost Protection Mode
1. The frost protection mode is integral to the appliance and
functions as long as there is power to the boiler, as indicated by
the standby signal
.
2. With CH & DHW or CH only selected, when the boiler
temperature falls below 5°C the boiler will fire until a
temperature of 30°C is reached.
3. If DHW only is selected, when the boiler CH temperature falls
below 5°C the boiler will fire until a temperature of 30°C is
reached. When the boiler DHW temperature falls below 5°C the
boiler will fire until a temperature of 7°C is reached.
4. Further protection can be incorporated by using a system
frost thermostat.
4.2.4
Pump Protection
1. This activates once a week if there has been no demand. The
pump runs for 30 seconds to prevent sticking.
EcoBlue Advance Combi
19
4
Description of the Product
4.3
Main Components
20
2
3
1
1.
Expansion Vessel
2.
Expansion Vessel Valve - Do NOT use as vent
3.
Primary Heat Exchanger
4.
Plate Heat Exchanger
5.
Pump with Automatic Air Vent
6.
Central Heating System Pressure Gauge
9
12
7.
Fan Assembly with Venturi
11
8.
Air/Gas Collector
10
9.
Flue Sensor
10.
Flame Sensing Electrode
11.
Spark Ignition Electrode
12.
Combustion Box Cover & Burner
13.
Control Box Display
14.
Condensate Trap
15.
Safety Pressure Relief Valve
23
8
24 16.
7
4
5
13
19
Drain Off Point
17.
Gas Valve
18.
Diverter Valve Motor
19.
Boiler Controls
20.
Boiler Adaptor
21.
Heating Flow Sensor
22.
Safety Thermostat
23.
Igniter
24.
Air Box
25.
Heating Return Sensor
26.
Hydraulic Pressure Sensor
27.
Domestic Hot Water Priority Sensor
(‘Hall Effect’ Sensor)
6
25
21
22
18
RQ
ADJ.
14
5
1
2
3
EV1
4
26
17
27
16
20
EcoBlue Advance Combi
16
7219715 - 03 (04/17)
Description of the Product
4.4
4
Control Panel Description
Key to Controls
R
Standby - Reset - Esc
Boiler Information View
Standby - Reset - Esc Button
Boiler Information View Button
Increase CH Temperature Button
R
/R
/P
Decrease CH Temperature Button
+
+
Increase DHW Temperature Button
Decrease DHW Temperature Button
Domestic Hot Water (DHW)
Temperature Adjustment
Central Heating (CH)
Summer / Winter / Only Heating Mode Button
Temperature Adjustment
Summer - DHW only mode
Summer - Winter - Heating Only
Mode
Winter - DHW & CH mode
Heating Only - Only CH mode
Display Description
DHW and CH OFF (frost protection still enabled)
Indicate errors that prevent burner from igniting
R
Error - Not resettable by user
Water pressure too low
R
Indicates an error resettable by the user
Indicates navigation in programming mode (parameter)
Indicates navigation in programming mode
Generic error
Burner lit
DHW mode (symbol will flash with demand)
Heating mode (symbol will flash with demand)
Display showing all available characters
Units for temperature
Units for pressure
R
Service due
7219715 - 03 (04/17)
EcoBlue Advance Combi
21
4
Description of the Product
4.5
Standard Delivery
1. The pack contains:
Boiler
Wall mounting plate (pre-plumbing jig) including
isolation valves
Fittings pack
Literature pack
• Installation & Servicing Manual (including ‘benchmark’)
• User Guide Instructions
• Flue Accessories & Fitting Guide
• Registration Card
• Fernox Leaflet
• Adey Leaflet
• Wall Template
• Product Leaflet
• Package Leaflet
4.6
Accessories & Options
4.6.1
Optional Extras
1. Various timers, external controls, etc. are available as optional
extras.
Plug-in Mechanical Timer Kit ----------------------------------------- 7212341
Plug-in Digital Timer Kit ------------------------------------------------ 7212342
Wireless RF Mechanical Thermostat Kit --------------------------- 7212343
Wireless RF Digital Programmable Room Thermostat Kit ---- 7212344
Single Channel Wired Programmable Room Thermostat Kit - 7212438
Wired Outdoor Weather Sensor ------------------------------------- 7213356
Two Channel Wired Programmer Kit ------------------------------- 7212443
Single Channel Wired Programmer Kit ---------------------------- 7212444
Mechanical Room Thermostat -------------------------------------- 7209716
Flue Accessories (elbows, extensions, clamps etc.)
(refer to the Flue Accessories & Fitting Guide supplied in the literature pack.)
Remote relief valve kit ------------------------------------------------- 512139
Boiler discharge pump ------------------------------------------------- 720648301
1M Drain Pipe ‘Trace Heating’ Element --------------------------- 720644401
2M Drain Pipe ‘Trace Heating’ Element --------------------------- 720664101
3M Drain Pipe ‘Trace Heating’ Element --------------------------- 720664201
5M Drain Pipe ‘Trace Heating’ Element --------------------------- 720664401*
*Where the drain is between 3 & 5 metres a 5 metre kit can be used and
“doubled back” upon itself.
Any of the above MUST be fitted ONLY by a qualified competent
person. Further detail can be found in the relevant sales literature
and at www.baxi.co.uk
22
EcoBlue Advance Combi
7219715 - 03 (04/17)
Before Installation
5
5
Before Installation
5.1
Installation Regulations
WARNING
Installation, repair and maintenance must only be
carried out only by a competent person. This
document is intended for use by competent persons,
Installation must be carried out in accordance with the prevailing
regulations, the codes of practice and the recommendations in
these instructions. Please refer to 1.5.1 and 1.6.2
Installation must also respect this instruction manual and any
other applicable documentation supplied with the boiler.
7219715 - 03 (04/17)
EcoBlue Advance Combi
23
5
Before Installation
5.2
5.2.1
Installation Requirements
Gas Supply
1. The gas installation should be in accordance with the relevant
standards. In GB this is BS 6891 (NG). In IE this is the current
edition of I.S. 813 “Domestic Gas Installations”.
2. The connection to the appliance is a 22mm copper tail located
at the rear of the gas service cock (Fig. 3).
3. Ensure that the pipework from the meter to the appliance is of
adequate size, and the demands of any other gas appliances in
the property are taken into consideration. Do not use pipes of a
smaller diameter than the boiler gas connection (22mm). UNLESS
the stated gas rate can be achieved with pipe of lesser diameter
and with all other gas appliances operating at maximum rate.
4. The gas service cock incorporates a pressure test point. The
service cock must be on to check the pressure.
5.2.2
Electrical Supply
1. External wiring must be correctly earthed, polarised and in
accordance with relevant regulations/rules. In GB this is the
current I.E.E. Wiring Regulations. In IE reference should be made
to the current edition of ETCI rules.
Fig. 3
Gas Service Cock
2. The mains supply is 230V ~ 50Hz fused at 3A.
The method of connection to the electricity supply must
facilitate complete electrical isolation of the appliance.
Connection may be via a fused double-pole isolator
with a contact separation of at least 3mm in all poles
and servicing the boiler and system controls only.
5.2.3
Hard Water Areas
Only water that has NOT been artificially softened must
be used when filling or re-pressurising the primary
system. If the mains cold water to the property is fitted
with an artificial softening/treatment device the source
utilised to fill or re-pressurise the system must be
upstream of such a device.
5.2.4
Bypass
1. The boiler is fitted with an automatic integral bypass.
5.2.5
System Control
1. Further external controls (e.g. room thermostat sensors) MUST
be fitted to optimise the economical operation of the boiler in
accordance with Part L of the Building Regulations. A range of
optional controls is available. Full details are contained in the
relevant Sales Literature.
24
EcoBlue Advance Combi
7219715 - 03 (04/17)
Before Installation
5.2.6
5
Treatment of Water Circulating Systems
1. All recirculatory water systems will be subject to corrosion
unless an appropriate water treatment is applied. This means
that the efficiency of the system will deteriorate as corrosion
sludge accumulates within the system, risking damage to pump
and valves, boiler noise and circulation problems.
2. When fitting new systems flux will be evident within the
system, which can lead to damage of system components.
3. BS7593 gives extensive recommendations on system
cleansing and water treatment.
4. All systems must be thoroughly drained and flushed out using
an appropriate proprietary flushing agent.
5. A suitable inhibitor must then be added to the system.
6. All system additives (flushing agents, cleansers, inhibitors
etc.) must comply with the requirements of BS7593. Full
instructions are supplied with the products and for further
information contact the additive manufacturer directly or consult
their website.
Failure to flush and add inhibitor to the system will
invalidate the appliance warranty.
7. It is important to check the inhibitor concentration after
installation, system modification and at every service in
accordance with the inhibitor manufacturer. (Test kits are
available from inhibitor stockists.)
8. For information or advice regarding any of the above contact
Baxi Customer Support 0344 871 1545.
5.2.7
Showers
1. If a shower control is supplied from the appliance it should be
of the thermostatic or pressure balanced type. Thermostatic
type shower valves provide the best comfort and guard against
water at too high a temperature. Existing controls may not be
suitable - refer to the shower valve manufacturer.
5.2.8
Expansion Vessel (CH only)
1. The appliance expansion vessel is pre-charged to 1.0 bar.
Therefore, the minimum cold fill pressure is 1.0 bar. The vessel
is suitable for correct operation for system capacities up to
125 litres (24 & 28)/155 litres (33 & 40). For greater system
capacities an additional expansion vessel must be fitted.
For GB refer to BS 7074 Pt 1. For IE, the current edition of I.S.
813 “Domestic Gas Installations”.
2. Checking the charge pressure of the vessel - to check the
charge accurately ensure the system is cold. It is also
necessary to relieve the pressure by draining the boiler. Using a
suitable gauge check the pressure at the valve on the underside
of the vessel. Adjust the pressure as required and repressurise
the system.
7219715 - 03 (04/17)
EcoBlue Advance Combi
25
5
Before Installation
5.2.9
Safety Pressure Relief Valve
See B.S. 6798 for full details.
1. The pressure relief valve (Fig. 5) is set at 3 bar, therefore all
pipework, fittings, etc. should be suitable for pressures in
excess of 3 bar and temperature in excess of 100°C.
2. The pressure relief discharge pipe should be not less than
15mm diameter, run continuously downward, and discharge
outside the building, preferably over a drain. It should be routed
in such a manner that no hazard occurs to occupants or causes
damage to wiring or electrical components. If it is anticipated
that any part of the pipe may be subject to freezing it should be
suitably insulated. The end of the pipe should terminate facing
down and towards the wall (Fig. 4).
3. The discharge must not be above a window, entrance or
other public access. Consideration must be given to the
possibility that boiling water/steam could discharge from the
pipe.
The end of the pipe should terminate facing
The relief valve must never be used to drain the system
down and towards the wall
4. A remote relief valve kit is available to enable the boiler to be
installed in cellars or similar locations below outside ground
level.
Fig. 4
5. A boiler discharge pump is available which will dispose of
both condensate & high temperature water from the relief valve.
It has a maximum head of 5 metres.
Section 6.2.1 gives details of how to connect the pipe
to the boiler.
Control Box
removed for clarity
Discharge Pipe
Pressure Relief Valve
26
EcoBlue Advance Combi
Fig.5
7219715 - 03 (04/17)
Before Installation
5.3
5.3.1
5
Choice of the Location
Location of the Appliance
1. The boiler may be fitted to any suitable wall with the flue
passing through an outside wall or roof and discharging to
atmosphere in a position permitting satisfactory removal of
combustion products and providing an adequate air supply. The
boiler should be fitted within the building unless otherwise
protected by a suitable enclosure i.e. garage or outhouse. (The
boiler may be fitted inside a cupboard-see Section 5.3.4).
2. Where the boiler is sited in an unheated enclosure and during
periods when the heating system is to be unused it is
recommended that the permanent live is left on to give BOILER
frost protection. NOTE: THIS WILL NOT PROTECT THE
SYSTEM !
3. If the boiler is fitted in a room containing a bath or shower
reference must be made to the relevant requirements.
In GB this is the current I.E.E. Wiring Regulations and Building
Regulations.
In IE reference should be made to the current edition of I.S. 813
“Domestic Gas Installations” and the current ETCI rules.
Fig. 6
Data Badge
Zone 2
4. If the boiler is to be fitted into a building of timber frame
construction then reference must be made to the current edition
of Institute of Gas Engineers Publication IGE/UP/7 (Gas
Installations in Timber Framed Housing).
Window
Recess
Zone 1
Zone 2
5.3.2
Data Plate
Zone 0
1. The boiler data badge gives details of the model, serial
number and Gas Council number and is situated on the boiler
lower panel. It is visible when the control box is lowered (Fig. 6).
0.6 m
Window
Recess
Zone 2
Fig. A
5.3.3
Where an integral timer is NOT FITTED the boiler has a
protection rating of IPX5D and if installed in a room
containing a bath or shower can be within Zone 2 (but
not 0 or 1).
In GB Only
Ceiling
Window Recess
Zone 2
Zone 1
Zone 2
Outside Zones
7219715 - 03 (04/17)
If the boiler is fitted with an integral timer it CANNOT be
installed in Zone 0, 1 or 2.
5.3.4
0.6 m
Fig. B
Figs. A & B shows zone dimensions for a bathtub. For other
examples refer to the Current I.E.E. Wiring Regulations).
Reference must be made to the relevant requirements.
In GB this is the current I.E.E. Wiring Regulations and Building
Regulations. In IE reference should be made to the current
edition of I.S. 813 “Domestic Gas Installations” and the current
ETCI rules.
2.25 m
Zone 0
In GB Only
Bath & Shower Rooms
Ventilation
1. Where the appliance is installed in a cupboard or
compartment, no air vents are required. BS 5440: Part 2 refers
to room sealed appliances installed in compartments. The
appliance will run sufficiently cool without ventilation.
EcoBlue Advance Combi
27
5
Before Installation
Examples are shown of the following methods of
termination:i) to an internal soil & vent pipe
ii) via an internal discharge branch (e.g. sink waste)
downstream of the trap
iii) to a drain or gully
iv) to a purpose made soakaway
v) pumped into an internal discharge branch (e.g.
sink waste) downstream of the trap
vi) pumped into an external soil & vent pipe
vii) to a drain or gully with extended external run &
trace heating
It is strongly recommended to discharge
internally into the household drainage system. If
connecting to a rain water drain, that drain MUST
discharge into a foul drain.
32mm
21.5mm
Insulation
5.3.5
Condensate Drain
FAILURE TO INSTALL THE CONDENSATE
DISCHARGE PIPEWORK CORRECTLY WILL AFFECT
THE RELIABLE OPERATION OF THE BOILER.
CAREFUL CONSIDERATION MUST BE GIVEN TO
THE POSSIBILITY OF THE PIPEWORK BEING
SUBJECT TO FREEZING CONDITIONS AND
APPROPRIATE MEASURES TAKEN TO PREVENT
BLOCKAGE. CORRECT INSTALLATION IN
ACCORDANCE WITH THIS SECTION WILL
CONSIDERABLY MINIMISE THE LIKELIHOOD OF
BLOCKAGE AND SUBSEQUENT BOILER LOCK-OUT.
A CONDENSATE DISCHARGE PUMP AND PIPE
‘TRACE HEATING’ ARE AVAILABLE AS
ACCESSORIES - see paragraphs 5.3.6.12 to 5.3.6.15
for further details.
The condensate discharge pipe MUST NOT RISE at
any point along its length. There MUST be a fall of AT
LEAST 2.5° (50mm per metre) along the entire run
EXCEPT when employing a suitable condensate pump
in basement and cellar or similar applications.
Key to
Pipework
i) Termination to an internal soil
and vent pipe
50mm
per m
etre o
2.5° M
inimum
f pipe
fall
run
450mm min*
*450mm is applicable to properties up
to 3 storeys.
For multi-storey building installations
consult BS 6798.
The boiler condensate trap incorporates a seal of
75mm, therefore it is unnecessary to install an air break
and trap in the discharge pipework.
1. The condensate outlet will accept 21.5mm (3/4in) plastic
overflow pipe. It is strongly recommended that this
discharges internally into the household drainage system.
Where this is not possible, discharge into an outside drain is
permissible providing every possible precaution is taken to
prevent freezing.
2. Ensure the discharge of condensate complies with any
national or local regulations in force. BS 6798 & Part H1 of the
Building Regulations give further detailed guidance.
3. The discharge pipe should be run in a proprietary drain pipe
material e.g. PVC, PVC-U, ABS, PVC-C or PP.
Boiler
Sink
ii) External termination via
internal discharge branch
e.g sink waste - downstream*
50mm
p
of pip er metre
e run
2.5° M
inimum
fall
Pipe must terminate
above water level but
below surrounding
surface. Cut end at 45°
4. Metal pipework is NOT suitable for use in condensate
discharge systems.
5. The pipe should be a minimum of 21.5mm diameter and must
be supported using suitably spaced clips of the correct design to
prevent sagging.
6. It is advisable that the full length of condensate pipe is
run internally and preferably be less than 3 metres.
7. Internal runs greater than 3 metres or runs in cold areas
should use 32mm waste pipe.
8. External runs MUST be a MINIMUM of 32mm and fully
insulated with material suitable for external use.
*It is NOT RECOMMENDED to connect upstream
of the sink or other waste water receptacle !
28
EcoBlue Advance Combi
7219715 - 03 (04/17)
Before Installation
9. If the boiler is fitted in an unheated location the entire
condensate discharge pipe should be treated as an external run
and sized and insulated accordingly.
iii) Termination to a drain
or gully
Boiler
10. In all cases discharge pipe must be installed to aid disposal
of the condensate. To reduce the risk of condensate being
trapped, as few bends and fittings as possible should be used
and any burrs on cut pipe removed.
50mm
p
of pip er metre
e run
2.5° M
inimum
11. When discharging condensate into a soil stack or waste
pipe the effects of existing plumbing must be considered. If soil
pipes or waste pipes are subjected to internal pressure
fluctuations when WC's are flushed or sinks emptied then backpressure may force water out of the boiler trap and cause
appliance lockout.
fall
Pipe must terminate above water level
but below surrounding surface. Cut
end at 45°
iv) Termination to a purpose made
soakaway
12. A boiler discharge pump is available which will dispose of
both condensate & high temperature water from the relief valve.
It has a maximum head of 5 metres. Follow the instructions
supplied with the pump.
Further specific requirements for
soakaway design are referred to in
BS 6798.
Boiler
50mm
pe
of pipe r metre
run
2.5° M
inimum
51
500mm min
13. Condensate Drain Pipe ‘Trace Heating’ Elements are
available in various lengths, 1, 2, 3 & 5 metres. Where the drain
is between 3 & 5 metres a 5 metre kit can be used and
“doubled back” upon itself.
fall
14. It is possible to fit the element externally on the condensate
drain or internally as detailed in the instructions provided.
Holes in the soak-away must
face away from the building
15. The fitting of a ‘Trace Heating’ Element is NOT a substitute
for correct installation of the condensate drain. ALL
requirements in this section must still be adhered to.
v) pumped into an internal discharge branch
(e.g. sink waste) downstream of the trap
50mm p
er metre
of pipe ru
2.5° Min
n
imum fa
ll
Sink
Boiler
Basement or
similar
Pipe must terminate
(heated)
above water level but
below surrounding
surface. Cut end at 45°
Condensate Pump
vi) pumped into an external soil & vent pipe
50mm
per me
tre of
2.5° M pipe run
inimum
fall
Unheated Location
(e.g. Garage)
Boiler
vii) to a drain or gully with extended
external run & trace heating
Boiler
Basement or similar
(heated)
50mm
The ‘Trace Heating’ element must be installed in
accordance with the instructions supplied.
External runs & those in unheated locations still
require insulation.
per me
tre of p
ipe run
inimum
fall
2.5° M
Pipe must terminate
above water level but
below surrounding
surface. Cut end at 45°
Condensate
Pump
7219715 - 03 (04/17)
EcoBlue Advance Combi
29
5
Before Installation
5.3.6
Clearances
1. A flat vertical area is required for the installation of the boiler.
2. These dimensions include the necessary clearances around
the boiler for case removal, spanner access and air movement.
Additional clearances may be required for the passage of pipes
around local obstructions such as joists running parallel to the
front face of the boiler.
*This is MINIMUM recommended dimension. Greater clearance
will aid installation and maintenance.
5mm Min
450mm
5mm Min
175mm Min (300mm
Min if using 80/125mm
flueing system)
At least
1.5°
450mm Min
763mm
For Servicing
Purposes &
Operating the
Controls
5mm Min In
Operation
345mm
150mm* Min
*This is MINIMUM
recommended dimension.
Greater clearance will aid
installation and maintenance.
Fig.7
30
EcoBlue Advance Combi
7219715 - 03 (04/17)
Before Installation
5.3.7
5
Flue/Chimney Location
1. The following guidelines indicate the general requirements for
siting balanced flue terminals. For GB recommendations are
given in BS 5440 Pt 1. For IE recommendations are given in the
current edition of I.S. 813 “Domestic Gas Installations”.
Due to the nature of the boiler a plume of water vapour
will be discharged from the flue. This should be taken
into account when siting the flue terminal.
T
J,K
U
N
R
I
M
C
I
I
F
D
E
A
S
I
F
J,K
B
L
A
A
G
H
H
I
Likely flue positions requiring
a flue terminal guard
Fig. 8
Terminal Position with Minimum Distance (Fig. 8)
A1
B1
C1
D2
E2
F2
G2
H2
I
J
K
L
M
N
R
S
T
U
Directly below an opening, air brick, opening windows, etc.
Above an opening, air brick, opening window etc.
Horizontally to an opening, air brick, opening window etc.
Below gutters, soil pipes or drain pipes.
Below eaves.
Below balconies or car port roof.
From a vertical drain pipe or soil pipe.
From an internal or external corner.
Above ground, roof or balcony level.
From a surface or boundary line facing a terminal.
From a terminal facing a terminal (Horizontal flue).
From a terminal facing a terminal (Vertical flue).
From an opening in carport (e.g. door, window)
into the dwelling.
Vertically from a terminal on the same wall.
Horizontally from a terminal on the same wall.
From adjacent wall to flue (vertical only).
From an adjacent opening window (vertical only).
Adjacent to windows or openings on pitched and flat roofs
Below windows or openings on pitched roofs
7219715 - 03 (04/17)
(mm)
300
300
300
25 (75)
25 (200)
25 (200)
25 (150)
25 (300)
300
600
1200
600
1200
1500
300
300
1000
600
2000
1
In addition, the terminal should be no nearer than
150 mm to an opening in the building fabric formed
for the purpose of accommodating a built-in element
such as a window frame.
2
Only ONE 25mm clearance is allowed per
installation. If one of the dimensions D, E, F, G or H
is 25mm then the remainder MUST be as shown in
brackets, in accordance with B.S.5440-1.
EcoBlue Advance Combi
31
5
Before Installation
Under car ports we recommend the use of the plume
displacement kit. The terminal position must ensure the
safe and nuisance - free dispersal of combustion
products.
2. If the terminal discharges onto a pathway or passageway,
check that combustion products will not cause a nuisance and
that the terminal will not obstruct the passageway.
3. If a terminal is less than 2 metres above a balcony, above
ground or above a flat roof to which people have access, then a
suitable terminal guard must be provided.
Terminal
Assembly
300 min
*
*4. Reduction to the boundary is possible down to 25mm but
the flue deflector must be used (see 5.3.12).
The distance from a fanned draught appliance terminal
installed parallel to a boundary may not be less than
300mm in accordance with the diagram opposite
(Fig. 9).
Top View Rear Flue
Fig. 9
Property Boundary Line
Plume
Displacement
Kit
If fitting a Plume Displacement Flue Kit, the air inlet
must be a minimum of 150mm from any opening
windows or doors (see Fig. 10).
Air Inlet
Opening
Window or Door
Fig. 10
32
EcoBlue Advance Combi
150mm
MIN.
The Plume Displacement flue gas discharge terminal
and air inlet must always terminate in the same
pressure zone i.e. on the same facing wall.
7219715 - 03 (04/17)
Before Installation
5.3.8
5
Horizontal Flue/Chimney Systems
1. The standard telescopic flue is suitable only for horizontal
termination applications.
(ii)
(i)
2. All fittings should be fully engaged. The approximate
engagement is 40mm. Apply the lubricant supplied to the seal on
each fitting to aid assembly.
3. Maximum permissible equivalent flue lengths are:(60/100)
(80/125)
Horizontal Concentric
10 metres
20 metres
4. Any additional “in line” bends in the flue system must be taken
into consideration.
Their equivalent lengths are:Concentric Pipes:
135° bend
0.5 metres
93° bend
1.0 metres
Flue length is measured from point (i) to (ii) as shown.
The elbow supplied with the standard horizontal
telescopic flue kit is not included in any equivalent
length calculations.
Horizontal
Flues
Read this section in conjunction with the Flue
Installation Guide supplied with the boiler.
WARNING
SUPPORT - All flue systems MUST be securely
supported at a MINIMUM of once every metre &
every change of direction. It is recommended that
every straight piece is supported irrespective of
length. Additional supports are available as
accessories.
VOIDS - Consideration must be given to flue systems
in voids and the provision of adequate access for
subsequent periodic visual inspection.
This bend is
equivalent to 1 metre
C
A
Plume Displacement Kit 60 /100 dia
1M Extensions 45° & 93° elbows are
also available - see the separate Flue
Guide.
(ii)
B
(i)
This bend is equivalent
to 1 metre
Total equivalent length =
A+B+C+2 x 90° Bends
NOTE: Horizontal flue pipes should
always be installed with a fall of at least
1.5° from the terminal to allow
condensate to run back to the boiler.
7219715 - 03 (04/17)
EcoBlue Advance Combi
33
5
Before Installation
5.3.9
m
0m
Flue/Chimney Lengths
1. The standard horizontal telescopic flue kit allows for lengths
between 315mm and 500mm from elbow to terminal without the
need for cutting (Fig. 11). Extensions of 250mm, 500mm & 1m
are available.
50
m
5m
31
The maximum permissible equivalent flue length is:
10 metres (60/100 system - vertical & horizontal)
20 metres (80/125 system - vertical & horizontal)
15 metres (80/80 twin pipe)
8 metres (60/100 system - vertical connected to ridge
terminal)
Fig. 11
5.3.10
Flue/Chimney Trim
1. The flexible flue trims supplied can be fitted on the outer and
inner faces of the wall of installation.
Ensure that no part of
the white outer chimney
duct is visible
5.3.11
Terminal Guard
1. When codes of practice dictate the use of terminal guards
(Fig. 12) ‘Multifit’ accessory part no. 720627901 can be used
(NOTE: This is not compatible with Flue Deflector referred to
below).
2. There must be a clearance of at least 50mm between any
part of the terminal and the guard.
3. When ordering a terminal guard, quote the appliance name
and model number.
4. The flue terminal guard should be positioned centrally over
the terminal and fixed as illustrated.
Fig. 12
Flue Deflector
5.3.12
Flue/Chimney Deflector
1. Push the flue deflector over the terminal end. It may point
upwards as shown, or up to 45° either way from vertical. Secure
the deflector to the terminal with screws provided (Fig. 13).
Fig. 13
G U I DA N C E N OT E S
5.3.13
Flue/Chimney Accessories
For full details of Flue Accessories (elbows, extensions,
clamps etc.) refer to the Flue Accessories & Fitting Guide
supplied in the literature pack.
Flue Accessories & Fitting Guide
Ø 60/100 Flue Systems
Ø 80/125 Flue Systems
Ø 80/80 Twin Flue Systems
Plume Displacement Kit (Ø 60/100 Flue Systems)
READ THESE INSTRUCTIONS IN CONJUNCTION WITH THE BOILER
INSTALLATION INSTRUCTIONS BEFORE FITTING THE FLUE
IMPORTANT NOTE: This document
will assist in the correct installation of
the various flue & chimney systems
described within. However, it is the
responsibility of the installer/Gas Safe
registered commissioning engineer to
ensure that the flue & chimney system
is fitted safely and in compliance with
the relevant standards and practices in
force in the country of installation.
Please leave these instructions with the
Installation & Servicing Instructions.
5.4
Transport
1. This product should be lifted and handled by two people.
When lifting always keep your back straight and wear protective
equipment where necessary. Carrying and lifting equipment
should be used as required. e.g. when install in a loft.
© Baxi Heating UK Ltd 2011
34
EcoBlue Advance Combi
7219715 - 03 (04/17)
Before Installation
5
Pre-plumbing Fig. 14
5.5
5.5.1
To remove only the Wall jig
slide banding to the edge
and open flaps.
Slide the wall jig out of
carton then close the flaps.
Slide banding back on.
Unpacking & Initial Preparation
Unpacking
RISK ASSESSMENT - Before commencing the
installation it is recommended that the ‘Five Steps to
Risk Assessment’ document published by the HSE is
consulted, and an assessment performed as described.
GAS SUPPLY - The gas supply, gas type and pressure
must be checked for suitability before connection.
1. See ‘Section 2.3.1 Handling’ before unpacking or lifting the
boiler.
2. Follow the procedure on the carton to unpack the boiler or
see Fig. 14a.
3. If pre-plumbing (Fig. 14) - the wall jig and fitting kit can be
removed without removing the carton sleeve. Simply slide
banding to the edge and open the perforated flap, lift out the jig,
fitting kit and instructions. If the boiler is to be install at a later
date, close the flap and reposition the banding straps, the boiler
can now be store safely away.
Remove Sealing
Caps from under
the Boiler before
lifting into position
A small amount of water may drain from the boiler in the
upright position.
5.5.2
SNAP OFF
Initial Preparation
1. After considering the location position the fixing template on
the wall ensuring it is level both horizontally and vertically.
Fig. 14a
2. Mark the position of the fixing slots for the wall mounting plate
indicated on the template.
Insert
Sealing
Washers
130mm
3. Mark the position of the centre of the flue hole (rear exit). For
side flue exit, mark as shown (Fig. 15).
4. If required, mark the position of the gas and water pipes.
Remove the template (Fig. 17).
LIFT HERE
BOTH SIDES
For Side Flue Exit
Fig. 15
6. Drill the wall as previously marked to accept the wall plugs
supplied. Secure the wall mounting plate using the fixing
screws.
Part No. 7212144
Side Flue
Centre Line
175 mm
Minimum
Clearance
116mm Dia Minimum
Aperture For Flue Tube
Vertical Flue
Centre Line
177 mm
Boiler Wall Mounting Plate
Fixing Slots
Ø 8 mm
50 mm
7. Using a spirit level ensure that the plate is level before finally
tightening the screws (Fig. 16).
Profile of
Outercase
5 mm Minimum
Side Clearance
5 mm Minimum
Side Clearance
3/4” BSP
Connections
Condensate
Drain
50 mm 45 mm
Pressure
Relief
Valve
(15mm)
65 mm
Heating
Flow
200 mm
(22mm)
Recommended
150 mm
Minimum
Clearance
5. Cut the hole for the flue (minimum diameter 116mm).
65 mm
Hot Water
Outlet
(15mm)
65 mm
Gas
Inlet
(22mm)
65 mm
Cold Water
Inlet
(15mm)
30
95 mm
Heating
Return
(22mm)
8. Connect the gas and water pipes to the valves on the wall
mounting plate using the copper tails supplied. Ensure that the
sealing washers are fitted between the connections.
Part No. 7212144 DRAFT A
NOTE: 40kW models ONLY - ensure the flow restrictor
is inserted in cold water inlet connection (Fig. 16). On
other models the restrictor is factory fitted internally.
Wall Template
Fig. 17
Fit the filling loop as described in the instructions
supplied with it.
5.5.3
Heating Flow
Fig.16
7219715 - 03 (04/17)
Flow Restrictor
(40 kW model only)
Flushing
1. Flush thoroughly and treat the system according to guidance
given in B.S. 7593.
EcoBlue Advance Combi
35
5
Before Installation
5.6
Stop
Valve
Double
Check
Valve
5.6.1
Stop
Valve
System Filling and Pressurising
1. A filling point connection on the central heating return pipework
must be provided to facilitate initial filling and pressurising and
also any subsequent water loss replacement/refilling.
2. A filling loop is supplied with the boiler. Follow the instructions
provided with it.
Temporary
Loop
DHW
Mains
Inlet
Fig. 18
Connecting Diagrams
CH
Return
3. The filling method adopted must be in accordance with all
relevant water supply regulations and use approved equipment.
4. Your attention is drawn to:
for GB: Guidance G24.2 and recommendation R24.2 of the Water
Regulations Guide.
for IE: the current edition of I.S. 813 “Domestic Gas Installations”.
Other Tap
Outlets
Expansion
Vessel*
Boiler
Check
Valve*
Pressure
Reducer Valve*
5. The sealed primary circuits may be filled or replenished by
means of a temporary connection between the circuit and a
supply pipe, provided a ‘Listed’ double check valve or some other
no less effective backflow prevention device is permanently
connected at the inlet to the circuit and the temporary connection
is removed after use.
5.6.2
To Hot
Taps
Domestic Hot Water Circuit
1. All DHW circuits, connections, fittings, etc. should be fully in
accordance with relevant standards and water supply regulations.
Stop Tap
Fig. 19
*See 5.6.2. for instances
when these items may be
required
In instances where the mains water supply incorporates a
non-return backflow prevention device, or any other device
that includes one*, it is possible for a build-up of pressure to
occur. This may result in damage to the boiler and other
appliances. To prevent damage to the boiler it is strongly
recommended that a suitable mini expansion vessel is fitted
on the mains water inlet between the boiler and the nonreturn device. *(The manufacturer of the device should be
consulted if there is any doubt regarding the presence of a
non-return feature).
Even in circumstances where a non-return device is not fitted
any future modifications to the mains inlet (e.g. fitting of a
water meter) should be considered and an expansion vessel
fitted. Baxi cannot accept any responsibility for damage to the
boiler if these recommendations are not followed.
Where Low Flow Taps or Fittings are intended to be used
in the DHW system connected to a Baxi EcoBlue Combi it
is strongly recommended that the DHW flow rate DOES
NOT fall below 2.5l/min. This will ensure reliable operation
of the DHW function.
36
EcoBlue Advance Combi
2. Your attention is drawn to:
for GB: Guidance G17 to G24 and recommendation R17 to R24
of the Water Regulations Guide.
for IE: the current edition of I.S. 813 “Domestic Gas Installations”.
3. The Water Regulations recommendations for England and
Wales prohibits backflow from appliances into the wholesome
water supply due to thermal expansion. However this type of
instantaneous combination boiler, with less than 15 litres of stored
capacity, does not require any backflow prevention device as any
thermal expansion is accommodated within the appliance.
It is possible in certain circumstances that other cold water
demands (e.g. washing machines, flushing of W.C.s) may affect
the DHW function of the boiler. In these instances the fitting of a
backflow prevention device and expansion vessel is
recommended.
If a check valve, loose jumpered stop cock, water meter
or water treatment device is fitted (or may be in the
future) to the wholesome water supply connected to the
boiler domestic hot water (DHW) inlet supply then a
suitable expansion device may be required.
4. The boiler’s maximum working mains pressure is 8 bar,
therefore all pipework, connections, fittings, etc. should be
suitable for pressures in excess of 8 bar. A pressure reducing
valve must be fitted for pressures in excess of 8 bar. The
manufacturer of any outlet fittings, such as a shower valve, may
require a lower maximum pressure. The pressure reduction must
take account of all fittings connected to the DHW system.
7219715 - 03 (04/17)
Installation
6
6
Installation
6.1
Engage the Boiler Mounting
Bracket on the Boiler into the
Retaining Lugs using the
Aligning Lugs for position
General
1. Remove the sealing caps from the boiler connections
including the condensate trap.
A small amount of water may drain from the boiler once
the caps are removed.
Retaining
Lugs
Remove Sealing Caps
from under the Boiler
before lifting into
position
2. Lift the boiler as indicated by the shaded areas. The boiler
should be lifted by TWO PEOPLE. Engage the mounting bracket
at the top rear of the boiler into the retaining lugs on the wall jig
using the aligning lugs for position (Fig.21) (see ‘Handling’
section 2.3.1).
3. Insert the sealing washers between the valves and pipes on
the wall jig and the boiler connections.
Aligning
Lugs
4. Tighten all the connections.
Sealing
Washers (x 5)
6.2
6.2.1
Bottom
Polystyrene
Fitting the Pressure Relief Discharge Pipe
1. Remove the discharge pipe from the kit.
2. Determine the routing of the discharge pipe in the vicinity of
the boiler. Make up as much of the pipework as is practical,
including the discharge pipe supplied.
Fig. 21
Lift Here
Both Sides
Assembly
When the Boiler Mounting Bracket on
the Boiler is in position on the
Retaining Lugs, the bottom polystyrene
may be discarded allowing the boiler to
swing into position
Make all soldered joints before connecting to the
pressure relief valve. Do not adjust the position of the
valve. The discharge pipe must be installed before
pressurising the system.
3. The pipework must be at least 15mm diameter and run
continuously downwards to a discharge point outside the
building. See section 5.2.9 for further details.
4. Utilising one of the sealing washers, connect the discharge
pipe to the adaptor and tighten the nut hand tight, plus 1/4 turn to
seal.
Pressure Relief Valve
5. Complete the discharge pipework and route it to the outside
discharge point.
Fig. 22
Discharge Pipe
Front Panel and Control
Box removed for clarity
7219715 - 03 (04/17)
EcoBlue Advance Combi
37
6
Installation
Prime Trap by
pouring 300ml of
water into flue spigot
6.2.2
Connecting the Condensate Drain
1. Remove the blanking cap, and using the elbow supplied,
connect the condensate drain pipework to the boiler condensate
trap outlet pipe.
Ensure the discharge of condensate complies with any
national or local regulations in force (see British Gas “Guidance
Notes for the Installation of Domestic Gas Condensing Boilers” &
HHIC recommendations).
2. The elbow will accept 21.5mm (3/4in) plastic overflow pipe
which should generally discharge internally into the household
drainage system. If this is not possible, discharge into an outside
drain is acceptable. See section 5.3.5 for further details.
Front Panel and
Control Box
removed for clarity
RQ
ADJ.
3. The boiler condensate trap should be primed by pouring
approximately 300ml of water into the flue spigot. Do not allow
any water to fall into the air inlet.
1
2
3
EV1
4
Fig. 23
Condensate Trap Connection
(elbow supplied)
6.3
6.3.1
Locating Lug
Preparation
Panel Removal
1. Remove the securing screws from the bottom of the case front
panel.
2. Lift the panel slightly to disengage it from the locating lugs on
top of the case and remove it.
Case Front
Panel
Case Front Panel
Securing Screws
38
EcoBlue Advance Combi
7219715 - 03 (04/17)
Installation
6
m
0m
6.4
50
5
31
Air Supply / Flue Gas Connections
mm
6.4.1
Connecting the Flue/Chimney
HORIZONTAL TELESCOPIC FLUE (concentric 60/100)
Terminal Assembly
1. There are two telescopic sections, the terminal assembly and
the connection assembly, a roll of sealing tape and two self
tapping screws. A 93° elbow is also supplied.
Connection Assembly
Fig. 24
2. The two sections can be adjusted to provide a length between
315mm and 500mm (Fig. 24) when measured from the flue elbow
(there is 40mm engagement into the elbow).
3. Locate the flue elbow on the adaptor at the top of the boiler.
Set the elbow to the required orientation (Fig. 25).
Wall Thickness
The flue elbow is angled at 93 degrees to ensure a fall
back to the boiler.
(X)
4. Measure the distance from the outside wall face to the elbow.
This dimension will be known as ‘X’ (Fig. 25).
5. If the distance from the flue elbow to the outside face of the
wall (‘X’ in Fig. 25) is less than 250mm the connection assembly
can be discarded and the terminal assembly fitted directly into the
elbow.
6. In instances where the dimension ‘X’ (Fig. 25) is between
250mm and 315mm it will be necessary to shorten the terminal
assembly by careful cutting to accommodate walls of these
thicknesses.
(X)
Wall
Thickness
Fig. 25
‘TOP’ Label
ion
‘Y’
7. To dimension ‘X’ add 40mm. This dimension to be known as
‘Y’.
8. Adjust the two telescopic sections to dimension ‘Y’ and seal the
joint with the tape provided (Fig. 27). Ensure that the labels
marked ‘TOP’ on the terminal and connection assemblies are
uppermost.
9. Using the clearance holes in the connection assembly secure
it to the terminal assembly using the screws supplied with the
telescopic flue (Fig. 28).
s
en
Dim
Sealing Tape
‘Peak’ to be
uppermost
‘TOP’ Label
Fig. 27
Securing Screw
Fig. 28
7219715 - 03 (04/17)
EcoBlue Advance Combi
39
6
Installation
10. Remove the flue elbow and insert the flue through the hole
in the wall. Fit the flue trims if required, and refit the elbow to the
boiler adaptor, ensuring that it is pushed fully in. Secure the
elbow with the screws supplied in the boiler fitting kit (Fig. 29).
Boiler Elbow
Apply the lubricant
supplied for ease of
assembly (do not
use any other type).
Adaptor
11. Draw the flue back through the wall and engage it in the
elbow. It may be necessary to lubricate to ease assembly of the
elbow and flue (Fig. 30).
Ensure elbow is
fully engaged into
boiler adaptor
12. Ensure that the terminal is positioned with the slots to the
bottom (Fig. 31). Secure to the elbow with the screws supplied
with the telescopic flue (Fig. 30).
Fig. 29
It is essential that the flue terminal is fitted as shown to
ensure correct boiler operation and prevent water
entering the flue.
13. Make good between the wall and air duct outside the
building, appropriate to the wall construction and fire rating.
Apply the lubricant
supplied for ease of
assembly (do not use
any other type).
14. If necessary fit a terminal guard (see Section 5.3.11).
Ensure Flue is fully
engaged into Elbow
There must be no part of the air duct (white tube)
visible outside the property.
Fig. 30
Slots at bottom
Fig. 31
40
EcoBlue Advance Combi
7219715 - 03 (04/17)
Installation
6
IMPORTANT
• Any wiring to the boiler, from either the mains or an external
control, MUST be cable of the following specification:0.75mm 3183/4/5Y (depending on installation) multi strand flexible
cable conforming to BS 50525-2-11.
• Cable of the above specification is sufficiently flexible to withstand
normal regular opening and closing of the facia/control box as
expected during routine servicing and other maintenance work.
• Use ONLY cable glands supplied with the boiler, or provided as
spares by the manufacturer.
• Under no circumstances must solid core cable be used as it is not
intended for applications where movement may occur. The use of
solid core cable could result in situations potentially hazardous to
health.
• These points must be considered when initially wiring the boiler to
the installation, and if replacing any wiring during the service life of
the boiler.
6.5
6.5.1
Electrical Connections
Electrical Connections of the appliance
The boiler must be connected to the mains fused 3A 230V
50HZ supply & control system using cable of 3 core 0.75mm
3183Y multi strand flexible type (see IMPORTANT note
opposite).
1. See Section 5.2.2. for details of the electrical supply. Undo the
securing screws and lift the case front panel off.
2. Hinge the control box downwards. Disengage the securing tabs
and open the terminal block cover. (Fig. 34).
3. If the mains cable fitted is not long enough slacken the gland
nut in the right of the boiler lower panel and pass the new mains
cable through it. Remove the grommet adjacent to the gland nut,
pierce the diaphragm and insert the cable from the external
control system.
4. Leave sufficient slack in the cables to allow the control box to
be hinged fully open. Tighten the gland nut and refit the grommet
and gland nut.
5. Connect the Earth, Permanent Live and Neutral wires to the
terminal strip.
Control Box
Both the Permanent Live and Neutral connections are
fused.
Fused Spur
L
Fig. 34
N
6. Refer to the instructions supplied with the external control(s).
Any thermostat must be suitable for 230V switching.
Room ‘Stat
N
Terminal M1
230V
b 1
bk 2
230V
g/y
b
N
7. Remove the link between connections 1 & 2. The 230V supply
at connection 2 must be connected to the thermostat. The
switched output from the thermostat must be connected to
connection 1. (Figs. 35 & 36). If the room thermostat being used
incorporates an anticipator it MUST be wired as shown in Figs. 35
& 36.
8. Replace the terminal block cover.
br
L
The 230V switched signal for external controls
(Frost Stat - Room Stat - Timer) must always be taken
from terminal 2 at the boiler. Live, Neutral and Earth to
power these controls must be taken from the Fused
Spur. For the Frost Stat to operate the boiler MUST BE
IN CENTRAL HEATING MODE i.e.
symbol shown.
Fig. 35
Frost Thermostat
Pipe Thermostat
Fused Spur
L
N
Room ‘Stat
9. Engage the front panel onto the locating lugs on top of the
case & secure with the securing screws at the bottom of the case.
230V
N
Terminal M1
230V
b 1
230V
g/y
External Clock
N
L
Fig. 36
7219715 - 03 (04/17)
bk 2
b
br
6.5.2
Connecting External Devices
1. See Section 6.7.2. for details of fitting the optional
outdoor sensor accessory.
6.6
Filling the Installation
1. See Section 5.2.6 and 5.6.1 for details of flushing
and filling the installation.
EcoBlue Advance Combi
41
6
Installation
6.7
6.7.1
External Controls
Installation of External Sensors
1. Various Sensors are available.
6.7.2
1/2 H
2.5m Min
Optional Outdoor Sensor
Full instructions are provided with the Outdoor Sensor Kit !
H
Positioning the Sensor
1. The sensor must be fixed to an external wall surface of the
property it is serving. The wall must face north or west.
West
North
DO NOT position it on a south facing wall in direct
sunlight !
N
E X
W
2. The sensor should be approximately half the height of the
living space of the property, and a minimum of 2.5m above
ground level.
3. It must be positioned away from any sources of heat or
cooling (e.g. flue terminal) to ensure accurate operation. Siting
the sensor above doors and windows, adjacent to vents and
close to eaves should be avoided.
S X
Connecting the Sensor
1. Ensure the electrical supply to the boiler is isolated. Undo the
securing screws and lift the case front panel off.
2. Hinge the control box downwards. Disengage the securing
tabs and open the terminal block cover.
3. Remove one of the grommets in the boiler lower panel, pierce
the diaphragm and insert the wires from the outdoor sensor.
4. Leave sufficient slack in the wires to allow the control box to
be hinged fully open. Refit the grommet.
5. Connect the wires from the outdoor sensor to positions 4 & 5
on M2 as shown. Refit the cover.
From Relay Box
10
9
5
4
10 9
87
65
43
21
M2 Low Voltage
Terminal Block
Setting the Sensor Curve
1. With the outdoor sensor fitted, the boiler central heating flow
temperature is adjusted automatically to accommodate the
change in heat required to optimise the efficient performance of
the boiler whilst maintaining a comfortable room temperature.
The central heating buttons on the boiler adjust a “simulated
room temperature” used for this optimisation.
2. This functionality requires the setting of three parameters on
the boiler, to suit the heating system and the optimisation can be
adjusted by the user with the central heating control buttons on
the boiler control panel.
Full instructions are provided with the Outdoor Sensor Kit !
Continue with the installation and commissioning of the
boiler as described in this manual.
42
EcoBlue Advance Combi
7219715 - 03 (04/17)
Commissioning
7
7
Commissioning
Automatic
Air Vent
7.1
Cap
General
1. Reference should be made to BS:EN 12828, 12831 & 14336
when commissioning the boiler. Ensure that the condensate
drain trap has been primed - see Section 6.2.2. paragraph 3.
2. At the time of commissioning, complete all relevant sections of
the Benchmark Checklist at the rear of this publication.
3. Open the mains water supply to the boiler and all hot water
taps to purge the DHW system.
4. Ensure that the filling loop is connected and open, then open
the heating flow and return valves on the boiler. Ensure that the
cap on the automatic air vent on the pump body is opened (Fig.
37).
Fig. 37
Pump
Control Box
removed for clarity
5. The system must be flushed in accordance with BS 7593
(see Section 5.2.6) and the flushing agent manufacturers
instructions.
6. Pressurise the system to 1.5 bar (Fig. 38) then close and
disconnect the filling loop.
7. Test for gas tightness, turn the gas supply on and purge
according to in GB BS 6891 and in IE I.S. 813 "Domestic Gas
Installations".
7.2
Checklist before Commissioning
7.2.1
Preliminary Electrical Checks
R
/R
/P
+
+
1. Prior to commissioning the boiler preliminary electrical system
checks should be carried out.
2. These should be performed using a suitable meter, and
include checks for Earth Continuity, Resistance to Earth, Short
Circuit and Polarity.
7.2.2
2
1. Checked:
1
3
4
0
bar
Digital pressure reading
which can be accessed
by via the
button
and scrolling to setting ‘5’.
Note there may be a
slight difference between
the digital & gauge
reading depending on
boiler operating mode.
7219715 - 03 (04/17)
Checks
Heating
Pressure Gauge
That the boiler has been installed in accordance with these
instructions.
The integrity of the flue system and the flue seals.
The integrity of the boiler combustion circuit and the relevant
seals.
Fig. 38
EcoBlue Advance Combi
43
7
Commissioning
7.3
7.3.1
Commissioning Procedure
De-Aeration Function
R
The display backlight remains lit approx. 10 minutes. If
the backlight goes out during commissioning it does not
mean that the process has been completed.
/R
/P
+
+
This procedure MUST be carried out !
1. Ensure the gas is turned Off! Turn the power to the boiler ON.
The software version will be displayed, followed by
, then ••
flashing briefly before displaying the ‘Standby’ symbol
.
These buttons for
De-Aeration
Fig. 39
2. Press
&
together and hold for at least 6 seconds
until
is briefly displayed followed by
.
FUNCTION INTERRUPTION
• If the De-aeration is interrupted due to a fault the pump will
cease to circulate but the function timer (approx.10 minutes)
will continue to run. For this reason it is recommended to
monitor the boiler display during De-aeration. If the fault
cannot be rectified quickly the function must be restarted to
ensure complete De-aeration.
• In the event of a loss of power the De-aeration function
needs to be restarted once the power is re-established.
• In the event of low water pressure the fault code E118 will
be displayed, along with the flashing
and
symbols.
This error can be rectified by repressurising the system to at
least 1.0 bar. The pump will restart automatically once the
water pressure is successfully re-established and
will
reappear in the display.
• The De-aeration function can be repeated as necessary
until all air is expelled from the system.
Flue Sampling
3. The De-Aeration Function is now activated. The boiler pump
will run for approx. 10 minutes. During this time the pump will
alternate on and off and the diverter valve will switch between
heating & hot water to purge air from the system.
4. At the end of the process the boiler will return to the ‘Standby’
position.
7.4
7.4.1
Gas Settings
Checking Combustion - ‘Chimney Sweep’ Mode
The case front panel must be fitted when checking combustion.
Ensure the system is cold & the gas supply turned on & purged.
The person carrying out a combustion measurement should
have been assessed as competent in the use of a flue gas analyser
and the interpretation of the results. See Section 10.1.3.
Important: Allow the combustion to stabilise before inserting the
Combustion Analyser Probe into the Test Point. This will prevent
saturation of the analyser.
R&
1. Press
together and hold for at least 6 seconds.
is displayed briefly followed by
and the current setting
point (eg. , or ) flashing alternately. Important: There may be a
delay before the boiler fires.
Point
Plug
Analyser Probe
2. To adjust the boiler input setting, press
or
button
and the current setting point will flash (eg. , or ). Press the
or
button again to alter the boiler input setting.
After refitting the sampling
point plug ensure there is no
leakage of products
= MAX. HEATING input,
= MAX. DHW input,
= MIN. input
4. The combustion (CO level & CO/CO2 ratio) must be measured
and recorded at MAXIMUM DHW input & MINIMUM input.
5. Follow the flow chart on the next page to comply with the
requirement to check combustion on commissioning.
The system MUST be cold to ensure the boiler is operating
under full demand. To obtain an accurate measurement on
smaller capacity systems it may be necessary to open one
or more hot taps and remove the diverter valve motor (see
Section 10.3.20) in order to maintain the boiler output.
R
/R
/P
+
+
6. Press
These buttons for
‘Chimney Sweep’
R&
7. Press the
again for at least 6 seconds to exit.
R once to bring the boiler out of ‘Standby’ mode.
8. Use the
button to toggle through the CH
settings to activate the required modes.
44
EcoBlue Advance Combi
and DHW
7219715 - 03 (04/17)
Commissioning
Set Boiler to Maximum Rate
(see 7.4.1)
Allow the combustion to
stabilise. Do not insert probe
to avoid ‘flooding’ the analyser.
7.4.1
7
Checking Combustion (cont)
9. Follow the flow chart opposite.
Verify Flue Integrity
Indication that products of
combustion & inlet air are
mixing - further
investigation is required.
Check all flue components
are correctly assembled,
fixed & supported. Check
the flue & terminal are
unobstructed.
Is O2 20.6% and
CO2 < 0.2% ?
No
TURN APPLIANCE OFF !
Call 0344 871 1545 for
advice.
The appliance MUST NOT
be commissioned until all
problems are identified
and resolved.
Perform Flue Integrity
Combustion Check
Insert the analyser probe into
the air inlet test point, allowing
the reading to stabilise.
No
Is O2 20.6% and
CO2 < 0.2% ?
Yes
Yes
Check CO & Combustion
Ratio at Maximum Rate
Whilst the boiler is still
operating at maximum insert
the analyser probe into the
flue gas test point, allowing
the reading to stabilise.
No
Is CO < 350ppm
and CO/CO2 ratio
< 0.004 ?
Verify Integrity of Seals
Check all burner seals,
internal flue seals, door &
case seals. Replace any
seals that appear unsound.
Is CO < 350ppm
and CO/CO2 ratio
< 0.004 ?
Yes
Set Boiler to Minimum Rate
(see 7.4.1)
Allow the combustion to
stabilise. Do not insert probe
to avoid ‘flooding’ the analyser.
Check CO & Combustion
Ratio at Minimum Rate
Whilst the boiler is
operating at minimum insert
the analyser probe into the
flue gas test point, allowing
the reading to stabilise.
Yes
No
TURN APPLIANCE OFF !
Call 0344 871 1545 for advice.
The appliance MUST NOT be
commissioned until all
problems are identified and
resolved.
If commissioning cannot be
fully completed the appliance
must be disconnected from the
gas supply in accordance with
the GSIUR.
Note: Check & record the CO
& combustion ratio at both
maximum & minimum rates
before calling 0344 871 1545.
7219715 - 03 (04/17)
No
Is CO < 350ppm
and CO/CO2 ratio
< 0.004 ?
Yes
BOILER OPERATING
SATISFACTORILY. NO
FURTHER ACTION
REQUIRED
Ensure test points are capped,
the boiler case front panel is
correctly fitted & secured and
all other commissioning
procedures completed.
Complete the ‘Benchmark’
Checklist, recording the CO &
combustion ratio readings as
required.
EcoBlue Advance Combi
45
7
Commissioning
7.5
7.5.1
Configuring the System
Check the Operational (Working Gas Inlet
Pressure & Gas Rate)
The system MUST be cold to ensure the boiler is
operating under full demand. To obtain an accurate
measurement on smaller capacity systems it may be
necessary to open one or more hot taps and remove
the diverter valve motor (see Section 10.3.20) in order
to maintain the boiler output.
1. Press
&
together and hold for at least 6 seconds.
is displayed briefly followed by
& flashing
alternately. ‘3’ represents MAXIMUM HEATING input.
2. Press
or
MAXIMUM DHW input.
Control Box removed
for clarity
to adjust the input.
represents
3. With the boiler operating in the maximum rate condition
check that the operational (working) gas pressure at the inlet
gas pressure test point is in accordance with B.S. 6798 & B.S.
6891. This must be AT LEAST 17mb !
4. Ensure that this inlet pressure can be obtained with all other
gas appliances in the property working. The pressure should be
measured at the test point on the gas cock (Fig. 41).
Gas Cock Inlet
Pressure Test Point
Measure the Gas Rate
5. With any other appliances & pilot lights turned OFF the gas
rate can be measured. It should be:Natural Gas
24 model
2.61 m3/h
28 model
3.05 m3/h
33 model
3.59 m3/h
40 model
4.35 m3/h
Fig. 41
P. OUT
VENT
RQ
ADJ.
Gas Valve
EV2
6. Press
&
to exit the function.
together and hold for at least 6 seconds
1
2
17-21 mbar
3
EV1
4
Gas Cock
7.6.1
18-22 mbar
19-23 mbar
Gas Meter
Fig. 41a
Working Gas Pressures
If the pressure drops are greater than shown in
Fig. 41a (above) a problem with the pipework or
connections is indicated. Permissible pressure
drop across system pipework < 1 mbar.
46
EcoBlue Advance Combi
7.6
Final Instructions
Handover
1. Carefully read and complete all sections of the Benchmark
Commissioning Checklist at the rear of this publication that are
relevant to the boiler and installation. These details will be
required in the event of any warranty work.
The warranty will be invalidated if the Benchmark
section is incomplete.
2. The publication must be handed to the user for safe keeping
and each subsequent regular service visit recorded.
3. Hand over the User’s Operating, Installation and Servicing
Instructions, giving advice on the necessity of regular servicing.
4 . For IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance with I.S. 813. An example of
this is given in I.S. 813 “Domestic Gas Installations”. This is in
addition to the Benchmark Commissioning Checklist.
7219715 - 03 (04/17)
Commissioning
7
5. Set the central heating and hot water temperatures to the
requirements of the user. Instruct the user in the operation of
the boiler and system.
Information Display
6. Instruct the user in the operation of the boiler controls.
The
button can be pressed so that the display shows
the following information:-
7. Demonstrate to the user the action required if a gas leak
occurs or is suspected. Show them how to turn off the gas
supply at the meter control, and advise them not to operate
electric light or power switched, and to ventilate the property.
‘00’ alternates with Sub-Code (only when fault on boiler) or ‘000’
‘01’ alternates with CH Flow Temperature
‘02’ alternates with Outside Temperature (where Sensor fitted)
‘03’ alternates with DHW Temperature
‘04’ alternates with DHW Temperature
‘05’ alternates with System Water Pressure
8. Show the user the location of the system control isolation
switch, and demonstrate its operation.
‘06’ alternates with CH Return Temperature
‘07’ alternates with Flue Temperature
9. Advise the user that they may observe a plume of vapour
from the flue terminal, and that it is part of the normal operation
of the boiler.
‘08’ - not used
‘10’ alternates with Zone 1 CH Flow Temperature
‘11’ alternates with Zone 2 CH Flow Temperature
‘12’ alternates with Ion current
‘13’ alternates with Burner working hours
‘14’ alternates with Zone 1 CH mode
‘15’ alternates with Zone 2 CH mode
‘16’ alternates with DHW circuit operating mode
‘17’ alternates with Boiler operating mode
‘18’ alternates with Solar plant operating mode
‘19’ alternates with Manufacturer information
7.6.2
System Draining
1. If at any time after installation it is necessary to drain & refill
the central heating system (e.g. when replacing a radiator) the
De-Aeration Function should be activated.
Re-pressurise the system to 1.5 bar
‘20’ alternates with Manufacturer information
Depending upon boiler model and any system controls
connected to the appliance, not all information codes will be
displayed and some that are will not have a value.
Press
R to return to the normal display.
2. On refilling the system ensure that there is no heating or hot
water demand, but that there is power to the boiler. It is also
recommended that the gas supply is turned off to prevent
inadvertent ignition of the burner.
3. Press
&
together and hold for at least 6 seconds.
The ‘De-Aeration’ Function will be activated.
4. The boiler pump will run for up to 10 minutes during which
time the diverter valve will switch between heating & hot water.
This will purge air from the system. The display will show
.
5. Once De-Aeration is complete recommission the appliance
and check that the inhibitor concentration is sufficient.
See Section 7.3.1 for more detail.
7219715 - 03 (04/17)
EcoBlue Advance Combi
47
8
Operation
8
Operation
8.1
General
1. It is the responsibility of the installer to instruct the user in the
day to day operation of the boiler and controls and to hand over
the completed Benchmark Checklist at the back of this manual.
2. Set the central heating and hot water temperatures to the
requirements of the user. Instruct the user in the operation of the
boiler and system.
3. The temperature on the boiler must be set to a higher
temperature than the cylinder thermostat to achieve the required
hot water demand.
4. Instruct the user in the operation of the boiler and system
controls.
5. Demonstrate to the user the action required if a gas leak
occurs or is suspected. Show them how to turn off the gas
supply at the meter control, and advise them not to operate
electric light or power switched, and to ventilate the property.
6. Show the user the location of the system control isolation
switch, and demonstrate its operation.
7. Advise the user that they may observe a plume of vapour from
the flue terminal, and that it is part of the normal operation of the
boiler.
8. The method of repressurising the primary system should be
demonstrated.
9. If at any time after installation it is necessary to drain & refill
the central heating system (e.g. when replacing a radiator) the
De-Aeration Function should be activated (see 7.6.2).
8.2
To Start-up
Switch on the boiler at the fused spur unit and ensure that the
time control is in the on position and any other controls (e.g.
room thermostat) are calling for heat.
Press the
R once to bring the boiler out of Standby mode.
The boiler will begin its start sequence.
8.3
To Shutdown
Isolate the mains power supply at the fused spur unit.
Isolate the gas supply at the boiler valve.
48
EcoBlue Advance Combi
7219715 - 03 (04/17)
Operation
Boiler Information
View
Standby - Reset - Esc
8.4
8
Use of the Control Panel
Key to Controls
R
Standby - Reset - Esc Button
R
/R
/P
+
Boiler Information View Button
+
Increase CH Temperature Button
Decrease CH Temperature Button
Domestic Hot Water
Temperature Adjustment
Central Heating
Temperature Adjustment
Increase DHW Temperature Button
Decrease DHW Temperature Button
Summer - Winter Heating Only Mode
Summer / Winter / Only Heating Mode Button
Display Screen
Summer - Winter - Heating Only Mode
R
1. Press
button until the required mode appears:Summer - DHW only mode
Winter - DHW & CH mode
Heating Only - Only CH mode
R
To increase or decrease the boiler temperature
1. Press
to increase the Central Heating temperature.
2. Press
to decrease the Central Heating temperature.
An overheat thermostat (NTC) is positioned in the heat
exchanger which shuts down the appliance if the boiler
temperature exceeds 100°C. Press
R button to
re-establish normal operating conditions.
R
To adjust the domestic hot water temperature
1. Press
temperature.
to increase the Domestic Hot Water
2. Press
temperature.
to decrease the Domestic Hot Water
8.5
Frost Protection
1. The boiler incorporates an integral frost protection feature
that will operate in both Central Heating and Domestic Hot
Water modes, and also when in standby ( displayed) see
section 4.2.3 Boiler Frost Protection Mode.
7219715 - 03 (04/17)
EcoBlue Advance Combi
49
9
Settings
9
Settings
9.1
Parameters
The operating parameters of the boiler have been factory set to
suit most systems.
50
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
10
Maintenance
WARNING
When changing components ensure that both the
gas and electrical supplies to the boiler are isolated
before any work is started. When the component has
been changed recommission the boiler as described
in Section 7.
Always examine any seals or gaskets, replacing
where necessary. The Case Front Panel MUST seal
effectively against the boiler side panels.
10.1 General
1. For reasons of safety and economy, it is recommended that
the boiler is serviced annually. Servicing must be performed by a
competent person in accordance with B.S. 7967-4.
2. After servicing, complete the relevant Service Interval Record
section of the Benchmark Commissioning Checklist at the rear of
this publication.
During routine servicing, and after any maintenance or
change of part of the combustion circuit, the following
must be checked:• The integrity of the complete flue system and the flue seals
by checking air inlet sample to eliminate the possibility of
recirculation. O2 20.6% & CO2 < 0.2%
• The integrity of the boiler combustion circuit and relevant
seals.
• The operational gas inlet pressure and the gas rate as
described in Section 7.5.1.
• The combustion performance as described in ‘Check the
Combustion Performance’ below.
3. Competence to carry out Checking Combustion
Performance B.S. 6798 ‘Specification for Installation &
Maintenance of Gas Fired Boilers not exceeding 70kWh’ advises
that:• The person carrying out a combustion measurement should
have been assessed as competent in the use of a flue gas
analyser and the interpretation of the results.
• The flue gas analyser used should be one meeting the
requirements of BS7927 or BS-EN50379-3 and be calibrated
in accordance with the analyser manufacturers’ requirements.
Flue Sampling
Point
Air Sampling
Point
After refitting the sampling
point plug ensure there is no
leakage of products
• Competence can be demonstrated by satisfactory completion
of the CPA1 ACS assessment, which covers the use of
electronic portable combustion gas analysers in accordance
with BS 7967, Parts 1 to 4.
4. Check the Combustion Performance (CO/CO2 ratio)
Set the boiler to operate at maximum rate as described
in Section 7.4.
5. Remove the plug from the flue sampling point, insert the
analyser probe and obtain the CO/CO2 ratio. This must be less
than 0.004. If the combustion reading (CO/CO2 ratio) is greater
than this, and the integrity of the complete flue system and
combustion circuit seals has been verified, and the inlet gas
pressure and gas rate are satisfactory either:• Perform the ‘Standard Inspection and Maintenance’ (Section
10.2) & re-check.
• Perform ‘Setting the Gas Valve’ (Section 10.3.25) & re-check.
• Replace and set the gas valve (Sections 10.3.24 & 25) &
re-check.
7219715 - 03 (04/17)
EcoBlue Advance Combi
51
10
Maintenance
10.2 Standard Inspection and Maintenance
Operation
When performing any inspection or maintenance
personal protective equipment must be used where
appropriate.
1. Ensure that the boiler is cool and that both the gas and
electrical supplies to the boiler are isolated.
2. Remove the screws securing the case front panel. Lift the
panel slightly to disengage it from the tabs on top of the case
(Fig. 43). Hinge down the control box.
3. To aid access disconnect the igniter plug & disconnect the
two pipes from the top of the condensate trap and the drain pipe
from the trap outlet. Undo the screw & washer securing the trap
to the boiler lower panel.
Case Front Panel
Securing Screws
Control Box
removed for clarity
4. Disengage the lip on the trap from the slotted bracket and
remove the trap. Take care not to spill any residual condensate
on the controls and P.C.B. Thoroughly rinse the trap and
examine the gasket on the trap base, replacing if necessary.
5. Remove the clip securing the gas feed pipe to the air/gas
venturi. Disconnect the pipe. Do not break the joint between the
pipe and gas valve unless necessary.
6. Note their position and disconnect the electrode leads and
the fan electrical plugs (Fig. 46).
Condensate Trap
7. Undo the four 10mm nuts retaining the combustion box cover
to the heat exchanger.
Gasket
8. Carefully draw the fan, collector and cover assembly forward
(Fig. 46).
Condensate Drain
Pipe Connection
9. Clean any debris from the heat exchanger and check that the
gaps between the coils are clear.
10. Inspect the burner, electrodes position (Fig. 45) and
insulation, cleaning or replacing if necessary. Clean any dirt or
dust from the boiler.
Fan, Collector and
Cover Assembly
11. Carefully examine all seals, insulation & gaskets, replacing
as necessary. Look for any evidence of leaks or corrosion, and
if found determine & rectify the cause.
Air Box
Electrode
Position
Fig. 45
Fig. 46
Securing Clip
Flame
Sensing
Electrode
Spark Ignition
Electrode
7.5
±1
Gas Feed
Pipe
4 ±0.5
12. Prime the trap and reconnect the pipes to the top.
Reassemble in reverse order.
Electrode
Leads
10 ±1
52
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
Expansion Vessel Charge - 1.0 bar
13. To check the charge accurately ensure the system is cold.
It is also necessary to relieve the pressure by draining the
boiler. Using a suitable gauge check the pressure at the valve
on the underside of the vessel. Adjust the pressure as required
and repressurise the system.
Expansion Vessel
Valve
Control Box
removed for clarity
A right angled valve extension will aid checking and
repressurising.
Hall Effect
Sensor
DHW Filter (Fig. 48)
14. If the flow of domestic hot water is diminished, it may be
necessary to clean the filter.
15. Turn the cold mains isolation cock (Fig. 47) off and draw off
from a hot tap.
Hydraulic
Inlet
Assembly
16. Disconnect the pump cable, remove the retaining clip and
extract the filter cartridge and rinse thoroughly in clean water.
Reassemble and check the flow.
View
underneath
appliance
Restrictor
(not on 40
models)
Filter
17. Check the operation of the Safety Pressure Relief Valve.
Simulate ‘Flame Failure’ fault by isolating the supply at gas cock
and operating the boiler. 133 should be displayed.
18. Reassemble the appliance in reverse order, ensuring the
front case panel is securely fitted. Recommission the boiler.
19. Complete the relevant Service Interval Record section of the
Benchmark Commissioning Checklist at the rear of this
publication and then hand it back to the user.
Fig. 48
DHW
Isolation Cock
10.3 Specific Maintenance Operations
Changing Components
Fig. 47
WARNING
When changing components ensure that both the
gas and electrical supplies to the boiler are isolated
before any work is started. When the component has
been changed recommission the boiler as described
in Section 7.
Always examine any seals or gaskets, replacing
where necessary. The Case Front Panel MUST seal
effectively against the boiler side panels.
Sealing
Gasket
Spark Ignition
Electrode
See Section 10.2 paragraph 2 for removal of case panel door
etc.
10.3.1
Electrode
Leads
Sealing
Gasket
Flame Sensing
Electrode
Fig. 49
7219715 - 03 (04/17)
Spark Ignition & Flame Sensing Electrodes
1. Note their position and disconnect the electrode leads.
Remove the retaining screws securing each of the electrodes to
the combustion box cover and remove the electrodes, noting
their orientation.
2. Check the condition of the sealing gaskets and replace if
necessary. Reassemble in reverse order (Fig. 49).
3. If satisfactory combustion readings are not obtained ensure
the electrode position is correct and perform the combustion
check again.
EcoBlue Advance Combi
53
10
Maintenance
10.3.2
Fan (Figs. 50 & 51)
1. Remove the clip securing the gas feed pipe to the air/gas
venturi. Disconnect the pipe.
2. Undo the screws securing the air/gas collector to the
extension piece and disconnect the fan electrical plugs (Fig. 50).
3. Remove the collector and fan assembly, being careful to retain
the gasket.
4. Undo the securing screw and remove the airbox, disengaging
it from the fan venturi. Undo the screws securing the fan to the
collector. Retain the gasket.
5. Undo the screws securing the venturi to the fan (noting its
position) and transfer to the new fan, replacing the seal if
necessary. Examine the gasket(s) and replace if necessary.
Control Box
removed for clarity
Cover
Gasket
Air/Gas
Collector
Air Box
Fan
Air/Gas
Venturi
Clip
Gas Feed
Pipe
Fig. 50
10.3.3
Air/Gas Venturi (Figs. 50 & 51)
1. Undo the securing screw and remove the airbox, disengaging
it from the fan venturi. Remove the clip securing the gas feed
pipe to the venturi.
2. Undo the screws securing the collector to the extension piece
and disconnect the fan electrical plugs.
Seal
Fan
Venturi
Fig. 51
3. Remove the collector and fan assembly, being careful to retain
the gasket.
4. Undo the screws securing the venturi to the fan (noting its
position) and fit the new venturi, replacing the seal if necessary.
Examine the gasket and replace if necessary.
5. After changing the venturi check the combustion - see Section
7.4.1.
54
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
10.3.4 Burner
Cover
1. Undo the securing screw and remove the airbox, disengaging
it from the fan venturi. Remove the clip securing the gas feed
pipe to the air/gas venturi and disconnect the fan electrical plugs.
Burner
Burner
Gasket
2. Undo the screws securing the air/gas collector to the
extension piece. Note its position and remove the extension
piece (where fitted) from the cover.
Extension Piece
(note orientation)
3. Undo the screws securing the burner. Withdraw the burner
from the cover and replace with the new one.
Gasket
4. Examine the gasket(s), replacing if necessary.
Note that the gaskets are not the same !
5. After changing the burner check the combustion.
Air Box
Fig. 52
Air/Gas
Collector
10.3.5
Insulation (Fig. 53)
1. Undo the securing screw and remove the airbox, disengaging
it from the fan venturi. Remove the clip securing the gas feed
pipe to the air/gas venturi and disconnect the fan electrical plugs.
2. Remove the electrodes as described in section 13.1.
Control Box
removed for clarity
3. Undo the nuts holding the cover to the heat exchanger. Draw
the air/gas collector, fan and cover assembly away.
Heat
Exchanger
Rear
Insulation
4. Remove the cover insulation piece.
5. Fit the new insulation carefully over the burner and align it with
the slots for the electrodes.
Seal
Air/Gas
Collector
Spark
Ignition
Electrode
Cover
Insulation
6. If the rear insulation requires replacement, remove it and all
debris from the heat exchanger. Also it may be necessary to
separately remove the spring clip from the pin in the centre of
the heat exchanger and the ‘L’ shaped clips embedded in the
insulation.
7. Do not remove the shrink-wrapped coating from the
replacement rear insulation. Keep the insulation vertical and
press firmly into position.
Air Box
Electrode
Leads
Flame
Sensing
Electrode
7219715 - 03 (04/17)
Fig. 53
8. Examine the cover seal and replace if necessary. Reassemble
in reverse order.
EcoBlue Advance Combi
55
10
Maintenance
10.3.6
Electrical
Plug
Flue Sensor
Flue Sensor
1. Ease the retaining tab on the sensor away and disconnect the
electrical plug.
3. Turn the sensor 90° anticlockwise to remove - it is a bayonet
connection.
4. Reassemble in reverse order.
10.3.7
Fig. 54
Igniter (Fig. 54)
1. Note the position of the ignition & sensing leads and
disconnect them. Also disconnect the igniter feed plug.
2. Undo the screw securing the igniter mounting bracket to the
left hand side panel. Remove the igniter and bracket and
transfer the bracket to the new igniter.
3. Reassemble in reverse order, reconnecting the plug and
leads to the igniter.
Igniter
10.3.8 Heating Flow & Return Sensors (Fig. 55)
Control Box
removed for clarity
Mounting
Bracket
Spark
Connection (‘A’)
Earth
Connection (‘B’)
1. There is one sensor on the flow (red wires) and one sensor
on the return (blue wires). Note: For access to the return sensor
first remove the fan and air/gas collector (see 10.3.2).
2. After noting the position prise the sensor clip off the pipe and
disconnect the plug.
3. Connect the plug to the new sensor and ease the clip onto
the pipe as close to the heat exchanger as possible.
Heating Flow
Sensor
10.3.9
Safety Thermostat (Fig. 56)
1. Pull the two spade connections off the safety thermostat.
Fig. 55
2. Remove the screws securing the thermostat to the mounting
plate on the flow pipe.
Safety Thermostat
Pump, Gas Valve
Assemblies and Pipework
removed for clarity
Retaining
Clip
3. Reassemble in reverse order, ensuring that the connections
are pushed fully on.
10.3.10 DHW NTC Sensor (Fig. 56)
1. Turn off the mains cold water supply tap and draw off the
residual domestic hot water.
2. Ease the retaining tab on the sensor away and disconnect the
electrical plug.
3. Unscrew the sensor from the hydraulic outlet assembly.
Examine the sealing washer, replacing if necessary.
Plug
4. Reassemble in reverse order. The plug will only fit one way.
DHW NTC Sensor
Hydraulic
Pressure Sensor
Fig. 56
56
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
10.3.11 Pump - Head Only (Fig. 57)
1. Drain the boiler primary circuit and disconnect the electrical
plug from the pump motor.
2. Remove the socket head screws securing the pump head to
the body and draw the head away.
3. Reassemble in reverse order.
10.3.12 Pump - Complete (Fig. 58)
1. Drain the boiler primary circuit and disconnect the electrical
plug from the pump motor.
2. Undo the two screws securing the body to the pipe and
manifold and draw the pump forwards.
3. Unscrew the automatic air vent from the pump body.
Control Box
removed for clarity
Socket Headed
Screw
4. Examine the ‘O’ ring seals on the return pipe and manifold,
replacing if necessary.
5. Fit the air vent to the pump body and reassemble in reverse
order.
10.3.13 Automatic Air Vent (Fig. 58)
Pump Body
1. Drain the boiler primary circuit and unscrew the automatic air
vent from the pump body.
Pump Head
2. Examine the ‘O’ ring seal, replacing if necessary and fit it to
the new automatic air vent.
Fig. 57
3. Reassemble in reverse order.
Automatic
Air Vent
Pump Flow
Pipe
Fig. 58
7219715 - 03 (04/17)
EcoBlue Advance Combi
57
10
Maintenance
10.3.14 Safety Pressure Relief Valve (Fig. 59)
1. Close the flow and return isolation taps and drain the primary
circuit.
2. Disconnect the discharge pipework from the valve. Remove
the sealing grommet.
‘O’ ring seal
3. Slacken the grub screw securing the pressure relief valve and
remove from the inlet assembly.
Grub Screw
4. On reassembly ensure that the ‘O’ ring is in place and the
sealing grommet is correctly refitted to maintain the integrity of
the case seal.
Safety Pressure
Relief Valve
10.3.15 Heating Pressure Gauge (Figs. 60 & 61)
Discharge Pipe
1. Close the flow and return isolation taps and drain the primary
circuit.
Fig. 59
2. Hinge the control box downwards. Remove the clip securing
the pressure gauge capillary to the hydraulic assembly.
3. Disengage the securing tabs and open the terminal block
cover. Prise apart the clips that hold the gauge cap.
4. Remove the gauge, cap and gasket.
5. Fit the new gauge, ensuring that the capillary is routed to
prevent any sharp bends. Locate the ridge on the gauge body in
the slot in the control box.
Clip
Control Box
removed for clarity
6. Reassemble in reverse order and ensure the gasket is in
position to maintain the integrity of the case seal.
Heating Pressure
Gauge Capillary
Fig. 60
Heating
Pressure
Gauge
Fig. 61
58
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
10.3.16 Plate Heat Exchanger (Figs. 62 & 63)
1. Close the flow & return isolation taps and the cold mains inlet.
Drain the primary circuit and draw off any residual DHW.
2. Refer to Section 10.2 paragraphs 5 to 9 and remove the fan
etc.
3. Undo the screws securing the plate heat exchanger to the
hydraulic assembly.
4. Withdraw the plate heat exchanger by manoeuvring it to the
rear of the boiler, then upwards and to the left to remove.
Plate Heat
Exchanger
Seals
5. There are four rubber seals between the hydraulic assembly
and heat exchanger which may need replacement.
Control Box
removed for clarity
6. Ease the seals out of the hydraulic assembly. Replace
carefully, ensuring that the seal is inserted parallel and pushed
fully in.
7. When fitting the new heat exchanger note that the right hand
location stud is offset towards the centre (Fig. 62).
8. Reassemble in reverse order.
Rubber Seal
R.H. Stud Fig. 62
Note offset
10.3.17 Hydraulic Pressure Sensor (Fig. 63)
1. Close the flow and return isolation taps and drain the primary
circuit. For ease of access remove the fan and collector
assembly.
Retaining Clip
2. Remove the plug from the sensor and pull the retaining clip
upwards.
3. Reassemble in reverse order.
Plug
Hydraulic
Pressure Sensor
Fig. 63
7219715 - 03 (04/17)
Pump, Gas Valve
Assemblies and Pipework
removed for clarity
EcoBlue Advance Combi
59
10
Maintenance
10.3.18 DHW Flow Regulator & Filter (Fig. 64)
1. Close the cold mains inlet and draw off any residual DHW.
2. Pull off the hall effect sensor. Undo the filter assembly from the
inlet/return manifold.
10.3.19 DHW Flow Sensor (‘Hall Effect’ Sensor)
(Fig. 65)
1. Pull the sensor off the DHW inlet manifold.
2. Disconnect the plug from the sensor and connect it to the new
component.
Control Box
removed for clarity
DHW Flow Sensor
3. Fit the new sensor, ensuring it is correctly oriented and fully
engaged over the manifold.
DHW Flow
Regulator & Filter
(‘Hall Effect’ Sensor)
10.3.20 Diverter Valve Motor (Fig. 66)
1. Disconnect the multi-pin plug. Pull off the retaining clip and
remove the motor.
Fig. 65
2. The motor can now be replaced,
3. When fitting the new motor it will be necessary to hold the unit
firmly while depressing the valve return spring.
Fig. 64
Hydraulic
Inlet
Assembly
Diverter
Valve Motor
Multi-pin
Plug
Retaining Clip
Valve
Assembly
Fig. 66
Pump, Gas Valve
Assemblies and Pipework
removed for clarity
60
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
10.3.21 Main P.C.B. (Fig. 67)
1. Ensure that the power to the boiler is isolated.
2. Release the clips securing the control box cover and lift away.
3. Note the position of all plugs and wires on the P.C.B. and
disconnect them.
See Section 3.3 Electrical Diagram for details.
4. Undo the 5 securing screws and remove the P.C.B. It is
retained at the left by two spring latches and the right hand edge
locates in a slot.
5. Reassemble in reverse order, ensuring that the harnesses to
the Control P.C.B. and terminal M2 are routed under the Main
P.C.B. Check the operation of the boiler.
10.3.22 Boiler Control P.C.B. (Fig. 67)
1. Ensure that the power to the boiler is isolated.
2. Release the clips securing the control box cover and lift away.
3. Note the position of all plugs and wires on the P.C.B. and
disconnect them.
See Section 3.3 Electrical Diagram for details.
Control
Box Cover
4. Undo the 5 securing screws and remove the P.C.B. It is
retained at the left by two spring latches and the right hand edge
locates in a slot.
5. Disconnect the link harness between the Main & Control
P.C.B.’s and undo the 4 screws securing the Control P.C.B.
6. Remove the Control P.C.B. and fit the new component.
Reassemble in reverse order, ensuring that the harnesses to the
Control P.C.B. and terminal M2 are routed under the Main P.C.B.
Check the operation of the boiler.
Main P.C.B.
Boiler Control P.C.B.
Fig. 67
7219715 - 03 (04/17)
EcoBlue Advance Combi
61
10
Maintenance
10.3.23 Expansion Vessel
Lock Nut
Expansion Vessel
1. Close the flow and return isolation taps and drain the boiler
primary circuit.
2. Undo the nut on the pipe connection at the bottom of the
vessel, and slacken the nut on the hydraulic inlet assembly.
3. Remove the screws securing the support bracket, and
withdraw the bracket.
4. Whilst supporting the vessel undo and remove the locknut
securing the vessel spigot to the boiler top panel.
Support Bracket
5. Manoeuvre the vessel out of the boiler.
6. Reassemble in reverse order.
10.3.24 Gas Valve (Fig. 69)
Fig. 69
After replacing the valve the CO2 must be checked and
adjusted as detailed in Section 10.3.25 Setting the Gas
Valve. Only change the valve if a suitable calibrated
combustion analyser is available, operated by a
competent person - see section 10.1.3.
1. Undo the screw and disconnect the electrical plug.
2. Turn the gas cock off and undo the nut on the gas valve inlet
underneath the boiler.
3. Undo the nut on the gas valve outlet. Ease the pipe aside.
NOTE: The gas nozzle injector is inserted in the gas valve outlet.
4. Remove the screws securing the gas valve to the boiler
bottom panel. Remove the valve.
Gas Feed
Pipe
5. Transfer the gas nozzle injector to the new valve, ensuring it
sits in the valve outlet. Examine the sealing washers, replacing if
necessary.
6. Reassemble in reverse order.
Washer
Gas Nozzle Injector
Check gas tightness & CO2 !
Gas Valve
Electrical
Plug
Washer
Gas Cock
Fig. 68
62
EcoBlue Advance Combi
7219715 - 03 (04/17)
Maintenance
10
10.3.25 Setting the Gas Valve (CO2 Check)
R
/R
/P
+
The CO2 must be only be checked and adjusted to set
the valve if a suitable calibrated combustion analyser is
available, operated by a competent person - see
Section 10.1.3.
+
1. The combustion (CO2) may be checked after running the
boiler for several minutes. To do this it is necessary to operate
the boiler in ‘Chimney Sweep Mode’.
‘Chimney Sweep Mode’
• This function must not be activated whilst the burner is lit.
• The case front panel must be fitted when checking
combustion.
• Ensure the system is cold
R&
1. Press
together and hold for at least 6
seconds.
is displayed briefly followed by
flashing
alternately with , or .
2. represents MAXIMUM HEATING input, represents
MAXIMUM DHW input whilst denotes MINIMUM input.
3. Press
or
The CO2 should be 8.7% ± 0.2 at MAXIMUM
2. It is possible to alter the CO2 by adjustment of the gas valve.
At maximum rate the Throttle Adjustment Screw should be
turned, using a suitable 2.5 hexagon key, until the correct
reading is obtained (Fig. 100).
Turning clockwise will reduce the CO2. Anticlockwise
will increase the CO2.
3. The CO2 must then be checked at minimum rate.
The CO2 should be 8.4% ± 0.2 at MINIMUM
to adjust the input.
4. The valve must be checked and set at MAXIMUM DHW
input & MINIMUM input.
4. With the boiler on minimum, the Offset Adjustment Screw
must be altered, using a suitable 4mm hexagon key, after
removing the cap (Fig. 100).
Turning anti-clockwise will reduce the CO2. Clockwise
will increase the CO2.
Flue Sampling
Point
Plug
5. Check the Combustion Performance (CO/CO2 ratio). This
must be less than 0.004.
Analyser Probe
Refit the sampling point plug and ensure there is no
leakage of products.
P. OUT
VENT
P.
R.
ADJ
.
EV2
Offset
Adjustment
Screw
(cap fitted)
RQ
ADJ.
Fig. 70
1
Throttle
Adjustment Screw
(cover removed)
2
EV1
3
4
Reduce CO2 Increase CO2
at min. rate at min. rate
Reduce CO2 Increase CO2
at max. rate at max. rate
Fig. 71
If the CO2 is reset at minimum
rate it must be rechecked at
maximum rate again and
adjusted if required. If the CO2
is reset at maximum rate it must
be rechecked at minimum rate
and adjusted if required.
7219715 - 03 (04/17)
Gas Valve
Do not turn the adjustment
screws more than 1/8 of a turn
at a time. Allow the analyser
reading to settle before any
further adjustment
EcoBlue Advance Combi
63
11
Troubleshooting
11
Troubleshooting
11.1 Error Codes
Table Of Error Codes
20
Central Heating NTC Fault
28
Flue NTC Fault
40
Central Heating Return NTC Fault
109 R
Possible Circulation Fault
110 R
Safety Thermostat Operated (pump fault)
111 R
Safety Thermostat Operated (over temperature)
117
Primary System Water Pressure Too High
118
Primary System Water Pressure Too Low
125 R
Circulation Fault (Primary)
128
Flame Failure (no lock-out)
130
Flue NTC Operated
133 R
Interruption Of Gas Supply or Flame Failure
151 R
Flame Failure
160 R
Fan or Fan Wiring Fault
321
Hot Water NTC Fault
384
False Flame
The
button can be pressed so that the display
shows
the following information:‘00’ alternates with Sub-Code (only when fault on
boiler) or ‘000’
‘01’ alternates with CH Flow Temperature
‘02’ alternates with Outside Temperature (where
Sensor fitted)
‘03’ alternates with stored DHW Temperature
‘04’ alternates with DHW Temperature
‘05’ alternates with System Water Pressure
‘06’ alternates with CH Return Temperature
‘07’ alternates with Flue Temperature
‘08’ - not used
‘09’ alternates with Collector Temperature
‘10’ alternates with Zone 1 CH Flow Temperature
‘11’ alternates with Zone 2 CH Flow Temperature
‘12’ alternates with Ion current
‘13’ alternates with Burner working hours
‘14’ alternates with Zone 1 CH mode
‘15’ alternates with Zone 2 CH mode
‘16’ alternates with DHW circuit operating mode
‘17’ alternates with Boiler operating mode
‘18’ alternates with Solar plant operating mode
‘19’ alternates with Manufacturer information
‘20’ alternates with Manufacturer information
1. If a fault occurs on the boiler an error code may be shown by
the facia display.
2. The codes are a flashing number, either two or three digit,
preceded by the symbol :followed by 20, 28, 40, 160 or 321 indicates possible faulty
components.
110 and 111 indicate overheat of the primary system water.
117 is displayed when the primary water pressure is greater
than 2.7 bar. Restoring the correct pressure will reset the error.
118 is displayed when the primary water pressure is less than
0.5 bar. Restoring the correct pressure will reset the error.
133, indicates that the gas supply has been interrupted,
ignition has failed or the flame has not been detected.
128 is displayed if there has been a flame failure during
normal operation.
125 is displayed in either of two situations:i) If within 15 seconds of the burner lighting the boiler
temperature has not changed by 1°C.
ii) If within 10 minutes of the burner lighting the boiler actual
temperature twice exceeds the selected temperature by 30°.
In these instances poor primary circulation is indicated.
3. By pressing the 'Reset' button for 1 to 3 seconds when
110, 125 & 133 are displayed it is possible to relight the boiler.
4. If this does not have any effect, or the codes are displayed
regularly further investigation is required.
11.2 Fault Finding
1. Check that gas, water and electrical supplies are available at
the boiler.
2. Electrical supply = 230V ~ 50 Hz.
3. The preferred minimum gas pressure is 20 mb (NG).
4. Carry out electrical system checks, i.e. Earth Continuity,
Resistance to Earth, Short Circuit and Polarity with a suitable
meter.
NOTE: These checks must be repeated after any servicing or
fault finding.
5. Ensure all external controls are calling for heat and check all
external and internal fuses. Before any servicing or replacement
of parts, ensure the gas and electrical supplies are isolated.
64
EcoBlue Advance Combi
7219715 - 03 (04/17)
Troubleshooting
Refer to “Illustrated Wiring Diagram” for position of terminals and components
Central Heating - Follow operational sequence
Turn on mains power
The display illuminates
NO
11
If
110 or 384 is flashing or re-occurs
regularly, check all PCB connections. If this
has no effect replace the PCB.
Go to section ‘A’
YES
110, 125, 133, or 384
flashing
YES
If
Press the reset button for 1
to 3 seconds
110 is still flashing
go to section ‘H’
NO
20, 28, 40 or 321
flashing
YES
Go to section ‘D’
NO
117 or 118 flashing
YES
Go to section ‘I’
Ensure controls are set to
demand and verify the
contacts are closed
NO
NO
Set Central Heating
temperature to Maximum.
symbol flashing, pump
runs
NO
Ensure all controls and
programmers are calling
for heat
YES
Go to section ‘B’
YES
Fan runs at correct speed
NO
160 flashing
Go to section ‘C’
NO
133 and R flashing
YES
Spark at ignition electrodes
up to 5 seconds & for 4
attempts
YES
YES
Go to section ‘F’. Press the
reset button for 1 to 3
seconds
YES
133 flashing
Go to section ‘G’
Go to section ‘E’
NO
Burner lights
YES
Burner goes out after 5
seconds
YES
Flame Displayed
NO
Check polarity
YES
109 flashing
YES
Go to section ‘J’
125 flashing after 1 min
NO
110 or 111 flashing
YES
Go to section ‘H’
NO
Diverter Valve open to
Central Heating circuit
NO
Go to section ‘K’
YES
Burner modulates to
maintain set temperature
NO
Check Heating Flow
sensor.
Go to section ‘D’
YES
130 flashing
YES
Go to section ‘M’
NO
Burner goes out
7219715 - 03 (04/17)
YES
Fan stops after 15
seconds
YES
Boiler operation correct
EcoBlue Advance Combi
65
11
Troubleshooting
Domestic Hot Water - Follow operational sequence
Turn on mains power
The display illuminates
NO
If
110 or 384 is flashing or re-occurs
regularly, check all PCB connections. If this
has no effect replace the PCB.
Go to section ‘A’
YES
110, 125, 133, or 384
flashing
YES
If
Press the reset button for 1
to 3 seconds
110 is still flashing
go to section ‘H’
NO
20, 28, 40 or 321
flashing
YES
Go to section ‘D’
NO
117 or 118 flashing
YES
Go to section ‘I’
Go to section ‘L’
NO
NO
Set Hot Water temperature to
Maximum & fully open hot tap.
symbol flashing, pump runs
Go to section ‘L’
NO
NO
DHW flow rate greater
than 2litres/min
YES
Burner lights
YES
YES
Fan runs at correct speed
NO
160 flashing
Go to section ‘C’
NO
133 and R flashing
Go to section ‘B’
NO
Spark at ignition electrodes
up to 5 seconds & for 4
attempts
YES
Go to section ‘F’. Press the
reset button for 1 to 3
seconds
YES
133 flashing
Go to section ‘G’
Go to section ‘E’
YES
NO
Burner lights
YES
Burner goes out after 5
seconds
YES
Flame Displayed
109 flashing
NO
YES
Check polarity
Go to section ‘J’
125 flashing after 1 min
NO
110 or 111 flashing
YES
Go to section ‘H’
NO
3 Way Valve open to
Domestic Hot Water circuit
NO
Go to section ‘K’
YES
Burner modulates to
maintain set temperature
NO
Check CH NTC sensor.
Go to section ‘D’
NO
130 flashing
YES
Go to section ‘M’
NO
Burner goes out
66
YES
EcoBlue Advance Combi
Fan stops after 15
seconds
YES
Boiler operation correct
7219715 - 03 (04/17)
Troubleshooting
11
Fault Finding Solutions Sections
A
Is there 230V at:
1.
2.
3.
B
NO
Main terminals L and N
Check electrical supply
NO
Main terminal fuse
Connection
OK at X40
Replace fuse
NO
Check wiring
PCB - X10 connector
Main terminals L and N
Display
illuminated
NO
Display or
Main PCB
fault
Switch to DHW mode maximum flow & press reset.
During next three minutes check :-
YES
230V at PCB - X11 connector 3 to 4
YES
230V at pump
Replace
pump
NO
NO
Check wiring
Replace PCB
C
Fan connections correct at fan &
PCB X11 and X23 connectors see Wiring Diagram.
NO
Make connections
YES
230V at PCB - X11 connector
(between blue & brown - see Wiring
Diagram)
YES
Fan jammed or
faulty wiring
YES
Replace fan or wire
NO
Replace PCB
D
Temperature sensor faulty.
Check correct location and wiring.
YES
Cold resistance approximately
10k @ 25° C (CH & DHW sensor)
20k @ 25° C (Flue sensor)
(resistance reduces with increase in temp.)
E
Gas at burner
NO
NO
Replace sensor &
reset boiler
Ensure gas is on and purged
Check wiring and PCB - X14
connector see Wiring Diagram
YES
Replace gas valve &
Check combustion
NO
Replace PCB
7219715 - 03 (04/17)
EcoBlue Advance Combi
67
11
F
Troubleshooting
Check and correct if necessary
1. Ignition electrode and lead
2. Electrode connection
3. Spark gap and position
YES
Check wiring (see Diagram)
and 230V at PCB X14 (between
blue & brown from igniter)
YES
NO
Replace PCB
4 ±0.5
Replace Igniter
Burner
Viewing Window
Flame
Sensing
Electrode
7.5
±1
Spark Ignition
Electrode
10 ±1
Fig. 72
Electrode Position
G
1.
2.
Check supply pressure at the
gas cock test point (Fig. 41):Natural Gas - Minimum 17 mbar
Check and correct if necessary
1. The set of the gas valve
(CO2 values - see Section 10.3.25)
2. Flame sensing electrode and lead connections
3. Flame sensing electrode position
Replace sensing electrode or PCB
H
Safety Thermostat operated
or faulty
NO
Check for and correct any
system faults
NO
Allow to cool. Continuity
across thermostat terminals
more than 1.5 ohm
YES
Replace safety thermostat
NO
Check Flow & Return
Sensors - see section ‘D’
YES
Is
110 or 111 still flashing ?
YES
Replace PCB
68
EcoBlue Advance Combi
7219715 - 03 (04/17)
Troubleshooting
CH system pressure less than
0.5 bar or greater than 2.7 bar
on digital display
I
NO
J
YES
Restore correct system pressure
YES
Check wiring and PCB X22 connector for approx.
5V DC between green &
black - see Wiring Diagram
Ensure that the boiler and
system are fully vented
NO
Replace hydraulic pressure sensor
NO
Replace PCB
System fault - correct
Check flow temperature sensor connections
and position.
Cold resistance approximately
10k @ 25° C (CH sensors)
(resistance reduces with increase in temp.)
YES
11
NO
Replace sensor
YES
Go to section ‘B’
K
Is there 230V at:
1.
PCB - X13 connector terminals between:Blue & Black (central heating mode)
Blue & Brown (domestic hot water mode)
see Wiring Diagram
NO
Replace PCB
YES
Check diverter valve motor cable
Is there 230V at:
2.
Diverter valve motor
Is mains water filter &
assembly clean, and rotor
moving freely ?
L
YES
YES
Replace diverter valve motor
Check wiring and PCB - X22
connector for approx. 5V DC
between red & blue from Hall effect
sensor - see Wiring Diagram
YES
Replace Hall Effect Sensor
NO
NO
Clean or replace
Replace PCB
M
1.
2.
Temperature sensors faulty.
Cold resistance approximately
10k @ 25° C (CH sensor)
20k @ 25° C (Flue sensor)
(resistance reduces with increase in temp.)
If pump is running the heat exchanger
could be obstructed
7219715 - 03 (04/17)
NO
YES
Replace sensor
Replace heat exchanger
EcoBlue Advance Combi
69
12
Decommissioning
12
Decommissioning
12.1 Decommissioning Procedure
1. Disconnect the gas & electric supplies and isolate them.
2. Drain the primary circuit and disconnect the filling device.
3. Dismantle the chimney system and remove the boiler from the
wall mounting frame.
70
EcoBlue Advance Combi
7219715 - 03 (04/17)
Spare Parts
13
13
Spare Parts
13.1 General
1. If, following the annual inspection or maintenance any part of
the boiler is found to need replacing, use Genuine Baxi Spare
Parts only.
C
13.2 Spare Parts List
Key
No.
D
A
Description
No.
Manufacturers
Part No.
A
Fan
Fan - 40 only
720768101
7211861
B
Burner - 24 & 28
Burner - 33
Burner - 40
7212447
7212449
7212448
C
Spark Ignition Electrode
720767301
D
Flame Sensing Electrode
7211855
E
Gas Valve
7214341
F
Safety Thermostat
720765301
G
Hall Effect Sensor
720788201
I
Plate Heat Exchanger
720852401
J
Diverter Valve Motor
720788601
K
Pump
7220533
M
Heating Flow/Return Sensor
720747101
N
DHW NTC Sensor
720789201
O
Pump Automatic Air Vent
720787601
P
Hydraulic Pressure Switch
720789001
Q
Heating Pressure Gauge
7212896
R
Flue Sensor
720851401
S
PCB - 24 ErP
PCB - 28 ErP
PCB - 33 ErP
PCB - 40 ErP
7222707
7222709
7222711
7222712
U
Ø5.0 Gas Nozzle Injector - 24
Ø5.6 Gas Nozzle Injector - 28
Ø6.6 Gas Nozzle Injector - 33
Ø6.8 Gas Nozzle Injector - 40
7211862
7214344
7211864
7214346
V
Air/Gas Venturi - 24
Air/Gas Venturi - 28
Air/Gas Venturi - 33 & 40
7211858
7211859
7211860
W
Boiler Control HMI PCB
7211868
B
E
G
F
J
M
P
O
U
N
R
Q
V
S
W
I
K
7219715 - 03 (04/17)
EcoBlue Advance Combi
71
14
Notes
14
Notes
72
EcoBlue Advance Combi
7219715 - 03 (04/17)
7219715 - 03 (04/17)
Notes
14
EcoBlue Advance Combi
73
GAS BOILER SYSTEM COMMISSIONING CHECKLIST
This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating
compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference.
Failure to install and commission according to the manufacturer’s instructions and complete this Benchmark Commissioning Checklist will invalidate the
warranty. This does not affect the customer’s statutory rights.
Customer name:
Telephone number:
Address:
Boiler make and model:
Boiler serial number:
Commissioned by (PRINT NAME):
Gas Safe register number:
Company name:
Telephone number:
Company address:
Commissioning date:
CONTROLS (tick the appropriate boxes)
Time and temperature control to heating
Time and temperature control to hot water
Room thermostat and programmer/timer
Programmable room thermostat
Load/weather compensation
Optimum start control
Cylinder thermostat and programmer/timer
Combination Boiler
Fitted
Not required
Heating zone valves
Hot water zone valves
Fitted
Not required
Thermostatic radiator valves
Fitted
Not required
Automatic bypass to system
Fitted
Not required
Boiler interlock
Provided
ALL SYSTEMS
’s instructions
Yes
What system cleaner was used?
What inhibitor was used?
Quantity
Yes
litres
No
CENTRAL HEATING MODE measure and record:
Gas rate
m³/hr
OR
ft³/hr
Burner operating pressure (if applicable)
mbar
OR Gas inlet pressure
mbar
°C
Central heating return temperature
°C
COMBINATION BOILERS ONLY
Is the installation in a hard water area (above 200ppm)?
Yes
No
Yes
No
DOMESTIC HOT WATER MODE Measure and Record:
Gas rate
m³/hr
OR
ft³/hr
Burner operating pressure (at maximum rate)
mbar OR Gas inlet pressure at maximum rate
mbar
Cold water inlet temperature
°C
Hot water has been checked at all outlets
Yes
Temperature
°C
I/min
CONDENSING BOILERS ONLY
The condensate drain has been installed in accordance with the manufacturer’s instructions and/or BS5546/BS6798
Yes
ALL INSTALLATIONS
Record the following:
At max. rate:
CO
ppm AND
At min. rate: (where possible)
CO
ppm AND
CO/CO²
CO/CO²
The heating and hot water system complies with the appropriate Building Regulations
Ratio
Ratio
Yes
The boiler and associated products have been installed and commissioned in accordance with the manufacturer’s instructions
Yes
The operation of the boiler and system controls have been demonstrated to and understood by the customer
Yes
The manufacturer’s literature, including Benchmark Checklist and Service Record, has been explained and left with the customer
Yes
Commissioning Engineer’s Signature
Customer’s Signature
*All installations in England and Wales must be
to Local Authority Building Control (LABC) either directly or through a
Competent Persons Scheme. A Building Regulations Compliance
will then be issued to the customer.
74
© Heating and Hotwater Industry Council (HHIC)
www.centralheating.co.uk
SERVICE RECORD
It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed.
Service Provider
Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions.
SERVICE 01
Date:
SERVICE 02
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
At max. rate:
Gas safe register No:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
Comments:
Comments:
Signature
Signature
SERVICE 03
Date:
SERVICE 04
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
At max. rate:
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
ppm
AND
Comments:
Signature
Signature
SERVICE 05
Date:
SERVICE 06
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
ppm
AND
Comments:
Signature
Signature
SERVICE 07
Date:
SERVICE 08
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
Date:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
Comments:
Comments:
Signature
Signature
SERVICE 09
Date:
SERVICE 10
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
CO² %
CO² %
Gas safe register No:
CO
At max. rate:
Date:
At min. rate: (Where Possible) CO
Comments:
Record:
CO² %
CO² %
Gas safe register No:
CO
At max. rate:
Date:
At min. rate: (Where Possible) CO
Comments:
Record:
CO² %
CO² %
Gas safe register No:
CO
At max. rate:
Date:
CO² %
CO² %
Date:
Gas safe register No:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
Comments:
Comments:
Signature
Signature
CO² %
CO² %
to Local Authority Building Control (LABC) either directly or through a
*All installations in England and Wales must be
Competent Persons Scheme. A Building Regulations Compliance
will then be issued to the customer.
© Heating and Hotwater Industry Council (HHIC)
www.centralheating.co.uk
75
Baxi Customer Support
0344 871 1545
Opening hours
Monday - Friday, 8.00am-6.00pm
Weekends and Bank Holidays, 8.30am-2.00pm
Please note calls may be recorded for training and monitoring purposes
baxi.co.uk
Register now to activate your warranty:
www.baxi.co.uk/registration
For the warranty to be maintained, please make sure...
1
2
3
Benchmark checklist is completed
Warranty is registered within 30 days
The boiler has an annual service
For full terms and conditions, visit www.baxi.co.uk/terms. Failure to adhere to
terms and conditions will void your manufacturer’s warranty.
Baxi
Brooks House,
Coventry Road,
Warwick, CV34 4LL
0086
Please ensure the boiler is installed in accordance with these installation
instructions and that you adhere to the Building Regulations.
e&oe
All descriptions and illustrations provided in this document have been
carefully prepared but we reserve the right to make changes and
improvements in our products which may affect the accuracy of the
information contained in this leaflet. All goods are sold subject to our
standard Conditions of Sale which are available on request.
7219715 - 03 (04/17)