Portable Evaporative Air Cooler User Manual Read and

Portable Evaporative Air Cooler
User Manual
Read and save these instructions before use
1
0.5
4
2
COOL
M
H
S
L
SWING
POWER
TIMER
SPEED
Scan Here/
Periksa Disini
http://www.honeywellaircoolers.com/products/CS10XE
www.honeywellaircoolers.com
E-mail: info@honeywellaircoolers.com
Model: CS10XE
PARTS DESCRIPTION
(7)
(1)
1
0.5
4
2
(6)
M
H
COOL
S
L
(2)
SWING
POWER
TIMER
SPEED
(3)
(8)
(4)
(13)
(9)
(14)
(10)
(11)
(15)
(12)
(5)
1) Display Screen
2) Control Panel
3) Louvers
4) Front Grill
5) Drain Plug
6) Handle
7) Remote Control
8) Honeycomb Cooling Media
9) Rear Grill
10) Water Fill Tray
11) Water Tank
12) Castors
(16)
13) Carbon Dust Filter
14) Water Level Indicator
15) Detachable Water Tank Latch
16) Power Cord & Plug
WARNING -- READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER
MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS
ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER
LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL
PREVAIL.
USE & OPERATION
CONTROL PANEL
Icons on Display Screen
M
1
0.5
4
2
Cool
M
H
Swing
H
L
0.5
Power ON / OFF
1
Timer Setting
4
2
COOL
SWING
POWER
TIMER
L
S
S
Fan Speed:
L - Low
M - Medium
H - High
S - Sleep*
SPEED
*Applicable for models with Sleep feature only.
FUNCTION BUTTONS
POWER
Press the POWER button to turn the unit on. The cooler will start automatically at medium speed. After a
few seconds the speed will switch to low. To turn the unit off, press the button again.
SPEED
Press the SPEED button repeatedly to change the speed between H - M - L - S*.
The indicator light will show the selected speed:
High (H)
Medium (M)
Low (L)
Sleep (S)*
When the SLEEP mode is selected, the fan will run on High for one hour, then Medium for the second
hour and on Low speed from the third hour onwards until you switch off the unit.
EN
1
USE & OPERATION (CONTINUED)
FUNCTION BUTTONS (CONTINUED)
TIMER
Press the TIMER button until the desired time duration setting is selected. When the set time has
passed, the unit will automatically turn off (unit remains in Standby mode until power cord is unplugged
from electrical socket). The TIMER function allows you to program the unit for up to 7.5 hours of use.
SWING
Press the SWING button until
is illuminated on the display screen.
The louvers will begin to move left to right automatically.
Vertical Air Flow - You can manually adjust the louvers to change vertical air flow.
LOUVER
MOVEMENT
COOL
Press the COOL button until
is illuminated on the display screen. This activates evaporative cooling.
The water pump will operate and you will feel the cooler air after the Honeycomb Cooling Media is
completely wet.
WARNING: Please ensure sufficient water is in the water tank otherwise you may hear a Low Water
Alarm and the cooler will start in a Fan only mode without evaporative cooling.
REMOTE CONTROL
Power
Speed
Cool
Swing
Timer
: ON / OFF
: Low / Medium / High / Sleep*
: Evaporative cooling ON / OFF
: Controls the motion of the louvers
: Controls the Timer function for automatic off
*Applicable for models with Sleep feature only.
Note:
t The remote control requires a CR2032 (1 x 3V) coin type or equivalent battery for replacement.
t Open the battery compartment at the back of the remote control and insert the battery inside. Care
must be taken to insert the batteries according to the correct polarity (+ / –) markings shown inside
the battery compartment.
t Always point the remote control signal transmitter towards the unit when operating. Make sure that
the signal path is not obstructed.
t Remove the batteries if the unit is not going to be used for an extended period of time.
t Do not drop the remote control.
t Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.
t Do not mix old and new batteries.
t Do not recharge the battery.
t Exhausted batteries are to be removed from the product and safely disposed of as per local
regulations.
t Do not dispose of batteries in fire. Batteries may explode or leak.
WARNING: Caution for ingestion of the small battery. Keep away from children and animals.
EN
2
USE & OPERATION (CONTINUED)
COOLER LOCATION
Make sure to position the air cooler correctly before you set up and start using the product. Please refer
to the COOLER LOCATION section of the separate Safety & Maintenance Guide.
FILLING WITH WATER
CAUTION:
Unplug the unit from the electrical power outlet before emptying or refilling the water tank.
Open the Water Fill Tray located at the back of the unit. The Water Level Indicator is located at the side
of the unit. Refill the water tank when water level is low. Do not fill water above the "Max." water level
mark to avoid water droplets collecting on the louvers. Check the water level in the tank before running
the
COOL function. Make sure that the water in the tank is above the minimum water level mark.
Running the unit in COOL mode with inadequate water may cause pump failure.
Note: The water capacity refers to the total volume of water that can be contained within the air cooler
water tank and water distribution system. The water capacity in the tank at the “Max.” indicator level
may be lower than the actual water capacity of the air cooler.
WARNING: Do not fill water tank with dirty water or salt water. This can damage the unit and
Honeycomb media.
LOW WATER ALARM
The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the
minimum level, you will hear a beeping sound and the
will flash continuously. The unit will
automatically pause evaporative cooling.
Refill the water tank to deactivate the alarm in cooling mode. First switch OFF the unit and unplug from
the power outlet. Fill the water tank with water above the minimum water level mark. Plug in and switch
ON again.
To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch the
unit OFF and then ON again. The Low Water Alarm will not activate in Fan only mode. The Low Water
Alarm will sound again if the COOL function is activated while the water tank is still empty.
CLEANING & DRAINING THE WATER TANK
Below are instructions on how to clean and maintain your air cooler. If the cooler will not be used for a
long period of time, please refer to the STORAGE & MAINTENANCE GUIDELINES located in the
separate Safety & Maintenance Guide.
EN
3
USE & OPERATION (CONTINUED)
CLEANING & DRAINING THE WATER TANK (CONTINUED)
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect from the electrical socket.
t Move the unit to a location where the water can be drained. Remove the cap from the Drain plug
located at the bottom of the unit. Allow the tank to empty.
t Detach the water tank by unlocking the Detachable Water Tank Latches on both sides of the unit. Lift
the cooler upwards away from the base and place it carefully and vertically on the floor. Be careful not
to bend the water pump tubes and other parts that will hang from the bottom of the unit when the
body is removed from the tank.
t Refill the water tank with clean water and drain it completely. Clean the water tank with dish detergent
or a damp cloth and rinse it thoroughly.
t Refill the water tank with clean water, up to the maximum level.
t Replace the top of the air cooler carefully back onto the tank and lock the side latches. The air cooler
is now ready to be used.
t Use a damp cloth to remove dirt and dust from the surface of the unit. Never use corrosive elements
or chemicals to clean this product.
t When the product is not in use, store the unit in a dry place out of direct sunlight.
CLEANING THE CARBON DUST FILTER* AND HONEYCOMB COOLING MEDIA
t The appliance is supplied with a Carbon Dust Filter* and
Honeycomb Cooling Media.
t The Carbon Dust Filter* and Honeycomb Cooling Media are
located inside the Rear Grill. See Figure 1 for instructions on
how to remove them from the unit for cleaning and
maintenance.
t Do not run the unit in COOL mode with stale water in the
tank. You must empty the water tank and refill with fresh
water, especially if the tank has not been cleaned in a long
time.
t The cleaning frequency for the Honeycomb media depends
on local air and water conditions. In areas where the mineral
content of water is high, mineral deposits may build up on the
Honeycomb Cooling Media and restrict air flow. Draining the
water tank and refilling with fresh water at least once a week
will help reduce mineral deposits. If mineral deposits remain
on the Honeycomb Cooling Media, the media should be
removed and washed under fresh water. The media should
be cleaned every two months or sooner, depending on your
needs.
t For best results allow the Honeycomb Cooling Media to dry
after each use by turning off the cool function 15 minutes
before turning the unit off.
Figure 1:
Honeycomb
Cooling Media
Carbon Dust
Filter
Honeycomb
Frame
Rear Grill
Screws
Removing the Carbon Dust Filter*/ Honeycomb Cooling Media:
1. Remove all the screws from the Rear Grill of the Air Cooler.
2. Carefully pull out the rear grill from the cooler.
3. Slide out the Carbon Dust Filter* and clean with water.
4. To release the Honeycomb Media, remove the Honeycomb
Frame screws and pull the Honeycomb Frame out of the
unit.
5. Remove the screws on the base of the Honeycomb Frame
and slide out the Honeycomb Cooling media. Replace or
clean media with water and a damp cloth as needed.
WARNING: DO NOT operate the Air Cooler when the
Rear Grill is removed from the Air Cooler, or if there is a
loose-fitting Rear Grill. Doing so can cause serious injury or
dangerous electrical shock.
*Applicable for models with Carbon Dust Filter only.
EN
4
TECHNICAL SPECIFICATIONS
Model
CS10XE
Voltage
220~240 V
Frequency
50 Hz
50Hz
Wattage
100 W
Water Tank Capacity
10 Litres / 2.6 Gallons*
Cooling Media
Honeycomb
700 (W) x 466 (D) x 1017 (H) mm
344 (W) x 400 (D) x 800 (H) mm
27.6 (W) x 18.3 (D) x 40.0 (H) in
13.5 (W) x 15.7 (D) x 31.5 (H) in
Product Dimension
Net Weight
8.4 kg / 18.5 lbs
ELECTRICAL WIRING DIAGRAM
Version: 220~240 V,
50 Hz
Capacitor
F/R
PLUG
H
Yellow
COOL
M
M
Blue
M
White
PUMP
L
Float sensor switch
L
N
Water tank
Power cutoff switch
JMATEK Limited
Manulife Financial Centre,
Kwun Tong, Hong Kong
Phone: 852-2559-5522
Email: info@jmatek.com
Web: www.jmatek.com
EN
Made in China
© 2017 JMATEK Limited. All rights reserved.
The Honeywell Trademark is used under license from
Honeywell International Inc.
Honeywell International Inc. makes no representations
or warranties with respect to this product.
This product is manufactured by JMATEK Limited.
Download PDF