e
e ee
e
Phase
ELECTRONIC AIR PURIFIER
Operation Manual
Model No. RespirAide 300T
Before operating the system, please read
this manual thoroughly, and retain it for
future reference.
This unit cannot be used in atmosphere
containing explosive dust, gas or oxygen,or
in an area where flammable dust is present.
If so, it may result in explosion or fire!
This product can be used only where the
power supply is 120V/60Hz. You cannot
use the unit if the power voltage is different.
S
te afe
st ty
ed
n
tio d
uc r e
od ito
Pr on
m
TUV
PRODUCT SERVICE
C
NRTL
ERI JU07655-7001
US
ISO 9001:2000
RespirAide Tech Inc.
Sensor
Manual
Timer
Auto
Remote control Button melody
Filter & UV lamp Safety switch
replacement alarm
Check alarm
13-100 Hanlan Road
Woodbridge, Ontario Canada
L4L 4V8
Tel: 1-866-874-2532
Fax: 1-905-850-5553
www.respiraide.com
R
**RespirAide is a trademark of RespirAide Tech Inc.
ENGLISH
WARNING
BEFORE OPERATING,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
CONTENTS
FOR CUSTOMER ASSISTANCE ...................................
CONSUMER LIMITED WARRANTY ............................
HOW IT WORKS ............................................................
FEATURES AND SPECIFICATIONS .............................
IMPORTANT SAFETY PRECAUTIONS ........................
Warning ...........................................................................
Cautions Concerning Operation ..................................
PART NAMES AND DESCRIPTION .............................
Main Unit .........................................................................
Part Numbers and Names .............................................
BEFORE OPERATION ....................................................
Remote Control Setup ..................................................
OPERATION ...................................................................
Display Indicator Lights ................................................
Main Unit Operation .......................................................
Remote Control Operation ............................................
CARE AND MAINTENANCE ........................................
Main Unit ........................................................................
Cleaning the Pre-filter ...................................................
Cleaning the Electronic Cell .........................................
Replacing the Activated Carbon Filter ........................
Photo catalytic Filter and UV Lamp .............................
TROUBLESHOOTING .....................................................
WIRING DIAGRAM .......................................................
SERVICE REMINDER SCHEDULE ...............................
E-3
E-4
E-5
E-6
E-7
E-8~11
E-8
E-8
E-12~13
E-12
E-13
E-14
E-14
E-15~17
E-15
E-16
E-17
E-18~20
E-18
E-18
E-19
E-19
E-20
E-21
E-22
E-23
FOR CUSTOMER ASSISTANCE
If you have questions about your air purifier, call the customer service number. Before calling, please note the
model and serial number located on the back of the unit and fill in the following information below. This
information will help us answer your questions much more quickly.
Model number
Serial number
Date of purchase
Dealer name
Address
City
Province
Postal code
Telephone
Phone: 1-866-874-2532
Write: For service problems, guarantee information, missing
items and other assistance:
RepirAide Tech Inc.
13-100 Hanlan Road Woodbridge, Ontario Canada
L4L 4V8
Please provide the following information when you write or call:
model number, serial number, date of purchase, your complete
mailing address (including Postal Code), your daytime telephone
number (including area code) and description of the problem.
E-4
CONSUMER LIMITED WARRANTY
RespirAide AIR PURIFIER
LIMITED WARRANTY
Congratulations on your investment
RespirAide Tech Inc. (hereinafter called RTI) gives you the following limited warranty for this product only if it was
originally purchased from RTI or from an Authorized RTI Dealer.
RTI warrants that this product is free, under normal use and maintenance, from any defects in material and
workmanship. If any such defects should be found in this product within the applicable warranty period. RTI
shall, at its option, repair or replace the product as specified herein.
RTI will repair or replace, free of charge, to the original purchaser, any part that is found to be defective in
material or workmanship within one (1) year of the date of purchase. This limited warranty does not cover the
replacement of expendable or consumable parts such as filters, and other parts subject to normal wear unless
they are defective in material or workmanship.
This warranty shall not apply if:
(A) Any defects caused or repairs required because of abusive operation, negligence, accident,
improper installation or inappropriate use as outlined in the operation manual.
(B) Any product tampered with modified, adjusted or repaired by any party other than RTI, RTI
Authorized Service Centers or RTI Authorized Service Dealers.
(C) Damaged caused or repairs required because of the use with items not specified or approved by
RTI.
(D) Any damage caused by external or environmental conditions, including but not limited to the use of
voltage other than indicated on the product.
RTI's limited warranty is valid only if you retain proof of purchase from RTI or an RTI Authorized Retail Dealer
for this product.
To obtain the name and address of the nearest
Authorized RespirAide Dealers, please contact:
13-100 Hanlan Road, Woodbridge, Ontario
Canada L4L 4V8
R
RespirAide Tech Inc.
For more information on this Warranty, Dealers or
Service Locations, please call 1-866-874-2532
Visit our website: www.respiraide.com
E-5
HOW IT WORKS
The air purifier functions as an air cleaner by helping to disinfect airborne microorganisms and removing
particulates from the air.
The centrifugal fans of the unit draw air through the front panel (Intake) on the front of the unit. Then it
passes through the Pre-filter, the Electrostatic precipitator, the Activated Carbon Filter and the UV-Photo
catalytic sterilization chamber. The purified air is then released through the outlet on the top of the unit.
The air is cleansed in six stages:
1. The Pre-filter traps large dust particles.
2. The two-stage electrostatic precipitator (Electronic Cell) captures airborne particles, as small as
0.01 microns. In the ionizing section of the electronic cell, billions of microscopic particles become
electrically charged as they pass through the powerful electric field. The collector plates
immediately attract and collect these charged dust and dirt particles.
3. The Activated Carbon Filter absorbs and reduces odors, chemicals and gases, removes tobacco
smoke, the smell of food and other odors.
4. The UV sterilization chamber kills bacteria and viral microorganisms such as influenza, TB and
Legionnaire's Disease as well as other harmful contaminants.
5. When UV light hits the photo catalytic filter, it creates e- and h+, which have an excellent effect in
the decomposition of odors.
6. The unit also generates negative ions that freshens the room air.
Clean Air Out
Stage 6
Dirty Air In
o
Dust acc
b
Bacteria
to
s
llen
Viru Po
Fungus
sm
e
ok
Stage 5
's
VOC
Stage 4
Stage 3
Stage 2
Stage 1
Stage 1
Pre-filter
Stage 2
Electronic Cell
Stage 3
Activated Carbon Filter
Stage 4
UV-C Germicidal Lamp
Stage 5
Photo Cataglyst
Stage 6
Negative Ion Generator
E-6
FEATURES AND SPECIFICATIONS
Features
Multi-Stage Filters
The unit utilizes a two-stage electrostatic precipitator combined with a Pre-filter (for large particles), an
Activated carbon filter (for odors and gases), UV germicidal light (killing airborne pathogen), a Photo
catalytic filter (removes VOC's) and a Negative ion generator.
Automatic Function
The gas sensor can let the unit automatically select the appropriate fan speed depending on the air quality
detected.
Filter and UV Lamp Replacement Indicator Lights
The "FILTER LIFE" and "UV LAMP" replacement indicators tell you when to replace the activated carbon
filter and the UV lamp.
Safety Micro-Switch (Interlock Switch)
This air purifier is equipped with a safety interlock switch (Micro-safety switch) that will turn the unit off if
the front panel is removed while the unit is running.
Easy Maintenance and Low Cost
When the electrostatic precipitator (Electronic cell) needs to be washed or the filters need to be replaced,
simply open the front panel and pull out the electronic cell or old filters and put the new or clean one in.
No screws, hooks or tools are required. The electronic cell captures small particles on aluminum plates
that are simply rinsed off in the sink. There are no expensive filters to replace.
Specifications
Model No.
RespirAide 300T
Power Requirement
120V, 60Hz, 0.71A
Rated Power
83W
Fan Motor
120V, 60Hz
Fan Speed
L-240m3/h, M-340m3/h , H-435m3/h
Noise Level
<55dB
Negative Ion
3x106pcs/cc
UV Lamp
6W
Cord Length
2.5m
Dimensions
H82.8cm x W47.8cm x D23.2cm
Weight
27.7kg
Standby Power
In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this product
consumes about 5.2W of standby power. For energy conservation, unplug the power cord when the
unit is not in use.
E-7
IMPORTANT SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should always be followed, including the following:
Warning-To reduces the risk of electrical shock, fire or injury:
-Use only as described in this manual.
-Use only a 120-volt outlet with a polarized receptacle.
-The air purifier has a polarized plug(one blade is wider than the other is), this plug will fit in a polarized outlet
only one way. Initially, if the plug does not fit into the outlet, reverse it. If it still does not fit, contact a qualified
electrician or service person.
-Do not use the air purifier if the power cord or plug is damaged or the connection to the wall outlet is loose.
-When removing the power plug, always hold the plug and never pull by the cord. Do not handle plug or
appliance with wet hands. Electrical shock or fire from short circuit may occur.
-Remove the power plug from the wall outlet before cleaning the unit and when not using the unit. Turn off all
controls before unplugging.
-If the power cord is damaged, it must be replaced by the manufacturer, its service agent, RespirAide
authorized service or similarly qualified person.
-Do not insert fingers or foreign objects into the intake or air outlet.
-The batteries must be removed from the remote control before disposal, and the batteries must be disposed
of safely.
-Keep hair, loose clothing, fingers and all parts of body always from openings and moving parts.
-Do not use the unit in an enclosed space where oxygen, flammable, explosive or toxic vapors are
given off by oil base paint, paint thinner, some mothproofing substances, or in an area where
flammable dust is present.
Cautions Concerning Operation
-Do not block the intake and air outlet.
-Do not use the unit near or on hot objects, such as range or where it may be exposed to steam.
-Always hold the handles on the side of the unit when moving it.
-Holding the front panel when carrying may cause it to detach, and result in bodily harm.
-Be careful not to tip over the unit when opening the front panel. If not, it may cause bodily harm.
-Do not operate the unit without filters.
-Do not wash or reuse the activated carbon filter.
-Do not clean outside with paint thinner or any chemicals. The unit surface may become damaged
or may cause fire.
E-8
IMPORTANT SAFETY PRECAUTIONS
This manual classifies precautions into WARNINGS and CAUTIONS. Be sure to follow
all precautions below: They are important for ensuring your safety.
WARNING
If you do not follow these instructions
exactly, the unit may cause minor
property damage or personal injury.
Acohol
If you do not follow these instructions
exactly, the unit may cause property
damage, personal injury or loss of life.
CAUTION
This unit can not be used in atmosphere
containing explosive dust, gas or in an area
where flammable substances are present.
If so, it results in explosion or fire!
Paint
thinner
Gasoline
DO NOT cleanse the unit or any parts (e.g. prefilter, electronic cell or activated carbon filter
etc.) with alcohol, gasoline, paint thinner or
other flammable substances. It may cause fire!
After cleaning the pre-filter, it is very important
to dry it completely before placing it back in the
unit. DO NOT clean pre-filter with flammable
substances (alcohol, gasoline, paint thinner,
etc.). It may cause fire!
DO NOT clean the cell with alcohol, gasoline,
paint thinner, etc. It may cause fire!
E-9
Paint
thinner
IMPORTANT SAFETY PRECAUTIONS
DO NOT wash or reuse the activated carbon
filter or clean the activated carbon filter with
liquid, especially alcohol, gasoline, paint thinner,
etc. It may cause fire! If it is dirty, vacuum it
with a soft brush.
The activated carbon filter must be located
behind the cell. DO NOT place the activated
carbon filter in front of the cell. It may cause
fire! (See page E-19~20)
Place the wire mesh side of the activated
carbon filter toward to the cell. If not, it may
cause fire! (See page E-19~20)
After cleaning the filters, make sure to dry the
cell thoroughly before reinstalling. If not, it
can cause breakdown of the unit or
personal injury.
Be careful not to tip over the unit when opening
the front panel or moving it. If not, It may
cause personal injury.
Do not block the intake or outlet. Blocked
openings can reduce capacity or damage the
unit.
E-10
IMPORTANT SAFETY PRECAUTIONS
125V 2A
Copper Wire
Do not disassemble or modify this equipment.
Unwarranted tampering can lead to fire, electric
shock and unit malfunction.
Use a fuse with proper capacity. Never use a
wire in place of a fuse. Doing this may lead to
malfunction or fire.
40 C
5C
Relative humidity<75%
Do not use the unit in humid places that might
be wet. Contact with water can lead to electric
shock or damage the equipment.
Use the product in the ambient temperature of
0-40 C.
If any parts of the power source gets wet
remove the plug and dry it completely before
reusing.
Do not place the product in direct contact with
sunlight. It may cause malfunction and
deformation of the product.
E-11
PART NAMES AND DESCRIPTION
Main Unit
211301
211201
211312
211501
211115
211110
202203
202501
202204
211111
211101
202807
211109
101201
211112
101324
211801
101529
101370
211102
101325
202109
211502
202915
101346
101351
202508
211103
202914
101345
211317
202906
202507
211904
211106
101348
101347
.Remote Control
(1 unit)
.Battery
(CR2025X1)
.Operation Manual
E-12
Part Numbers and Names
211201 Plastic Top Cover
211301 Display Circuit Board
211312 Gas Sensor
211501 Fan Motor Screen
211110 Screen metal frame
211115 Fan motor top plate
202203 Fan Housing
202501 Fan Motor Side Plate
202204 Fan Blade
211101 Unit Housing
101201 Unit Handle
211102 Bottom Plate
202508 Caster
101345 Main Circuit Board transformer
211317 Main Circuit Board
211103 Circuit Board Protector
101346 Power supply transfomer
101351 Power Supply
101370 Interlock Switch
101325 UV Lamp Holder
202109 UV Light Blocker
E-13
211502 Power Contact Plate
202915 Activated Carbon Filter (Complete)
202906 Electronic Cell (Complete)
202914 Pre-filter (Complete)
202507 Ground Contact Plates
211106 Front Panel Unit (Air Intake Grill)
101529 Magnetic Catcher
211801 Unit Epoxy Resin Board
202807 Photo Catalyst Filter
211112 Fan Motor Bottom Plate
211109 Upper Panel
211111 Fan Motor Front Plate
211904 Remote Control
101348 Power Cord Socket
BEFORE OPERATION
Remote Control Setup
Preparing the remote control
The battery is already set in the remote control, pull out the clear sheet from the battery cover
before using.
How to use the remote control
a) Point the transmitter of the remote control towards the receiver of the main unit. If an
obstruction to the signal exists, the remote control will not operate.
b) The distance from which the remote control can transmit is approximately 19 feet (6m).
Front side
Back side
+
CR2025 Battery
Battery Information
1. Open the cover on the rear of the remote control towards the arrow.
2. Replace the battery with CR2025 battery. Be sure to set the battery with the (+) side up.
3. Close the cover to its original position.
4. The battery for this remote control is for initial use only. Change the battery when necessary.
5. When not using the unit or remote control for an extended period, remove the battery.
6. Store the battery where babies and children cannot reach them. If the battery is
swallowed contact a doctor immediately.
7. When discarding battery, cover the terminals of the battery with tape. If mixed with other metal or
batteries, heat, explosion or combustion may occur.
8. Bring the battery to a nearby electronics store, watch store or camera store to recycle them.
Remote Control
1. Do not drop or place the remote control in water. (Damage may occur.)
2. Do not press the remote control buttons with sharp objects. (Damage may occur.)
3. The remote's signal may not be received properly if fluorescent lamps (such as inverter
fluorescent lamps) are in the same room.
4. Operate with the remote control facing the main unit receiver.
5. The signal range is about 19 feet (6m).
6. Make sure there are no objects blocking the path of the signal.
7. Avoid dropping or damaging the remote control.
8. Do not use it in high humidity conditions or in direct sunlight or near a heat source.
E-14
OPERATION
Display Indicator Lights
SPEED Indictator Light
When the power is on, the
unit is set at the L speed
indicator light, select the
speed by pressing the
SPEED button.
TIMER Indicator Light
When the TIMER
button pressed, the
indicator light will light
up. The indicator light
shows the set time.
Remote receiver
Receive signals from
remote control
AUTO Indicator Light
When the unit is at
Auto mode, the light
will light up.
Gas sensor
air inlet
1h
2h
3h
TIMER
L
M
H
AUTO
SPEED
POWER
CHECK
CHECK Indicator
Light
When the indicator
light flashes red with
beeping, please
contact customer
service.
FILTER LIFE
UV LAMP
NEG. ION
UV LAMP Indicator
Light
When the UV lamp
works the light is on
and if the indicator light
flashes, it tells the time
for UV lamp to be
replaced.
FILTER LIFE Indicator Light
When the FILTER LIFE indicator
light flashes yellow, the carbon
filter needs to be replaced.
ON
Power ON Indicator Light
When the power cord is inserted to
the outlet, the light will light up
yellow and pressing the POWER
button to start the unit it will turn to
green.
NEG. ION Indicator Light
When the indicator light is green, negative ions
are discharged. One press of the NEG.ION
button will stop the generation of ions and the
light will go out.
E-15
OPERATION
Main Unit Operation
Connect the Power
When the power plug is inserted into the wall outlet, all the indicators on the display panel will light up for 2
seconds. (As shown in the diagram below)
3. TIMER Button
Press the TIMER button to select
the time for operation. Each time it
is pressed the timer setting
switches as shown below:
1. POWER Button
Press the POWER
(ON/OFF) button to start
operating the unit.
Pressing the button again
will stop operation.
1hr-2hr-3hr
Cancel
1h
2h
TIMER
3h
L
M
H
AUTO
SPEED
POWER
CHECK
FILTER LIFE
UV LAMP
NEG. ION
ON
2. SPEED Button
4. UV LAMP Button
When pressed, turn off the
UV lamp, pressing again will
turn on the UV light with the
indicator light on.
Each time the SPEED Button is
pressed the airflow rate changes
as shown below:
L ------ M ------ H ----- AUTO----- L... ...
5. NEG.ION Button
When pressed, the
generation of ions will
cease and the negative
ion generator light on the
control panel will go out.
E-16
OPERATION
Remote Control Operation
POWER (ON/OFF) Button
The unit will start operating when the
POWER button is pressed. Pressing
the button again will stop operation.
Transmitter
SPEED Button
The fan speed can be
switched among Low,
Medium and High settings.
TIMER Button
The set time switches every
time the button is pressed as
shown below.
**The indicator light shows
the set time.
1hr-2hr-3hr
Cancel
NEG.ION Button
When pressed, the generation
of ions will cease and the
negative ion generator light on
the control panel will go out.
UV LAMP Button
When pressed, turn off
the UV lamp.
NIGHT Button
When pressed, all the indicator
lights will go out except the
green ON light on the control
panel.
AUTO Button
At AUTO mode, the fan speed
is automatically switched (H, M,
L) depending on the amount of
pollution in the air.
RESET1 and RESET2 buttons
After replacement of activated
carbon filter, make sure to press
RESET1 button 5 times to reset
the filter timer. Also, after
replacing the UV lamp, press the
RESET2 button 5 times to reset
the UV lamp timer.
Before pressing the RESET
buttons, be sure the unit is
plugged in.
Press the RESET1 button 5 times to Press the RESET2 button 5
reset the timer for activated carbon times to reset the timer for UV
filter: 1, 2, 3, 4, 5-beep~
lamp: 1, 2, 3, 4, 5-beep~
E-17
CARE AND MAINTENANCE
WARNING
Cleaning the unit while it is plugged in may result electric shock, electric spark and
serious injury. Unplug the unit before cleaning or maintenance!
To maintain optimum performance of this air purifier, please clean the unit including the pre-filter and electronic
cell periodically. When cleaning the unit, be sure to unplug the power cord, and never handle the plug
with wet hands. Electrical shock and bodily injury may occur as a result.
Main Unit
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to remain, they may
become difficult to remove. Wipe with a dry, soft cloth for stubborn stains or dirt, use a soft cloth dampened with
warm water. Do not use volatile fluids, Benzene, paint thinner, polishing powder, this may damage the
surface.Do not use detergents, detergent ingredients may damage the unit. Keep the unit away from water.
Cleaning the Pre-filter
To assure optimum performance the Pre-filter should be cleaned
regularly-every one to two weeks. Washing frequency will vary
depending on the number of family members, pets, activities (such
as cooking or woodworking) and smoking habits. Use the wash
reminder schedule provided with the air purifier.
1. Stop the operation and unplug the unit.
2. Hold the front panel upper portion (left and right side) and pull it
toward you.
3. Pull the pre-filter straight up and out of the front panel.
4. After using a vacuum cleaner to remove any dust, clean
with water. If it is very dirty, use a soft brush or a neutral
cleaner to clean then dry completely before placing it back into
the unit.
5. Place the pre-filter back into the front panel by sliding straight
down into the slots.
Removing the pre-filter
WARNING
1. DO NOT clean the pre-filter with
flammable substances (alcohol,
gasoline, paint thinner, etc.).
It may cause fire!
2. After cleaning the pre-filter, it is
very important to dry it completely
before placing it back in the unit.
3. During maintenance, be careful not
to tip over the unit. It may cause
personal injury.
E-18
CARE AND MAINTENANCE
Cleaning the Electronic Cell
Remove the electronic cell
1. Stop the operation and unplug the unit.
2. After waiting for 5-10 seconds, open the front panel.
3. Pull the cell straight up and out of the front panel.
How to clean the electronic cell
1. To assure optimum performance the cell should be cleaned
every one to two months.
2. Use a large enough container, such as a laundry tub or trash
container. Dissolve detergent in warm water to cover the cell.
After the detergent has completely dissolved, place the cell in
the container. Allow the cell to soak for 15~30 minutes and
rinse with clean water. Tough residue such as tar from tobacco
smoke may need longer soaking.
3. After cleaning, make sure to rinse detergent residue thoroughly
out of the ceramic insulators of the cell. Dry the cell thoroughly
with heat gun before reinstalling.
Removing the cell
WARNING
1. DO NOT clean the cell with alcohol, gasoline, paint thinner
or other flammable substances. It may cause fire!
2. DO NOT reinstall the cell until it is completely dry. If the
"CHECK" light on the control panel flashes red, then the cell
may still be wet.
3. Be sure there is no detergent residue around the cell
ceramic insulators, especially around the square shape
ceramic insulators.
4. Be careful not to snag or cut the ionizing wire. If the unit is
operated with the ionizing wire cut, there will be no dust collection.
5. Slide in the cell so the airflow arrow points toward the machine.
Cleaning the cell
Replacing the Activated Carbon Filter
When the "FILTER LIFE" indicator light on the control
panel flashes yellow, the activated carbon filter needs to
be replaced.
1. Stop the operation and unplug the unit.
2. After waiting for 5-10 seconds open the front panel.
3. Remove the old activated carbon filter and insert
new one.
4. After replacing the activated carbon filter, press the
"RESET1" button 5 times to reset the filter timer
(See page E-17 of this manual).
Replacing the activated carbon filter
IMPORTANT:
A. DO NOT clean the activated carbon filter with liquid, especially alcohol, gasoline, paint thinner, etc.
It may cause fire! If it is dirty, vacuum it with a soft brush.
B. DO NOT try to place the activated carbon filter in front of the cell! It may cause fire!
C. The WIRE SCREEN SIDE of the activated carbon filter should face the cell (See below figures).
E-19
CARE AND MAINTENANCE
Wire screen
side
Carbon filter
side
Correct
Wrong
Place the activated carbon filter so that the wire
screen side is facing the cell!
DO NOT place the carbon fiber side facing the
cell or in front of the cell! It may cause fire!
Photo catalytic Filter and UV Lamp
1. Photo catalytic filter is permanent, never needs replacing. When there is dust on it, clean the dust off using a
vacuum cleaner dusting brush. Do not wash it in water.
2. When the "UV LAMP" indicator light on the control panel flashes yellow, it is time to replace the UV lamp (UV-C
germicidal lamp). After removing the UV light blocker, gently rotate the lamp a quarter turn in either direction
until it unlocks from the socket. Pull the pins out the sides of the socket, one end at a time.
CAUTION:
Photo catalytic filter
UV-C
germicidal lamp
Replacing UV lamp
Helpful Hints
After replacement of activated carbon filter or UV lamp, be sure to
press Filter Reset Button (RESET1 Button) or UV Lamp Reset Button
(RESET2 Button) on the remote control for 5 times.
Once the Reset Buttons have been activated, you will hear a beep
sound that means that the unit has been reset and the FILTER LIFE or
UV LAMP indicator lights will stop flashing.
E-20
Germicidal Light Radiation
Hazard!
Never look directly at UV lamp or
place face directly on outlet grill.
Direct exposure to germicidal light
can cause temporary or chronic
damage to your eyesight, or even
blindness.
Always unplug the unit before
cleaning, servicing or replacing the
UV lamp.
TROUBLESHOOTING
Service problems that appear to be major can often be solved easily. You can be your own troubleshooter by
reviewing the following guide. All other servicing should be done by a Surgicall Clean Air authorized service center.
Case
The system does not
operate at all
What to Check
Measure
Power failure?
Check other electrical appliances.
Power plug disconnected?
Make sure to insert the plug.
The FUSE out of order?
Replace the FUSE with new one.
Front panel open or interlock switch
failure?
The unit does not operate when the front panel is
detached. Install properly. Check interlock switch.
Is the Check Unit light flashing?
The cell may be wet after cleaning. Dry it thoroughly.
If not, call the Customer Service.
When functions do not There is too much dust on the
Pre-filter, carbon filter?
work
Clean the filter or replace it.
There is too much dust on the
electronic cell?
Wash it and dry completely before installing it.
The air inlet or outlet blocked?
Get rid of foreign materials around the product.
Automatic function
There is too much dust on the sensor? Remove dust on the sensor.
does not work properly
There is no dust on the sensor.
When other problems
in terms of functions
are found
Call the Customer Service.
Check the problems first and then unplug the power cord. Call the Customer Service to
ask for after-sale service or make inquiries.
E-21
Collector
(2nd stage)
E-22
Blue
White
Fan motor
White
Red
Red
Negative ion
generator
Transfomer
Blue
Y. green
Power supply
(HVG)
UV lamp and ballast
Y. Green
Y. green
Black
Red
18V
Ionizer
(1st stage)
JZ9
White
White
JZ8
Yellow
Black
Blue
Red H
M L
C
Red
Red
Black(-)
Red(+)
F1
JZ12
JZ11 JZ10
JZ7
JZ5
JZ6
JZ3
Pink white
JZ1
White
Black
Transformer
JZ2
JZ13
Pink white
JZ5
Display Board
JZ4
Gas sensor
Interlock switch
Interlock switch
Green
Power cord
socket
Fuse
AC120V, 60Hz
WIRING DIAGRAM
Model. 300T
Reset button
Pink white
Remote control
receiver
Main Circuit Board
Electronic cell
WIRING DIAGRAM
SERVICE REMINDER SCHEDULE
Pre-filter Wash Reminder
Year
J
F
M
A
M
J
J
A
S
O
N
D
J
J
A
S
O
N
D
Memo:
Electronic Cell Wash Reminder
Year
J
F
M
A
M
Memo:
E-23
RespirAide Tech Inc.
13-100 Hanlan Road
Woodbridge, Ontario Canada
L4L 4V8
Tel: 1-866-874-2532
Fax: 1-905-850-5553
www.respiraide.com
R
RespirAide reserves the right to revise or modify products and/or specifications
without notice.The contents of this manual are subject to change without notice.
0709-1-500-211704
Download PDF