Top Global Wireless LAN

BELLEDS Technologies. ---- Q Station User Guide
QLight User Guide
For iOS
Q Station Firmware: r358 and above
(Support iOS Version: 6.1 and above)
2015-01-19
Belleds Technologies Co., Ltd., any modification of this product will not issue a separate notice.
All Rights Reserved.
-1-
BELLEDS Technologies. ---- Q Station User Guide
CONTENT
1
2
3
4
INTRODUCTION .......................................................................................................... 3
1.1
VERIFY KIT CONTENTS ............................................................................................ 3
1.2
CONNECTION .......................................................................................................... 4
CONFIGURATION ....................................................................................................... 7
2.1
ENTER CONFIGURATION PAGE .................................................................................. 7
2.2
CONFIGURATION IN DETAIL ....................................................................................... 8
2.2.1
Music Service ................................................................................................. 8
2.2.2
Basic Settings .............................................................................................. 11
2.2.3
Internet Connection...................................................................................... 17
2.2.4
Upgrade Firmware ....................................................................................... 23
QLIGHT IN IOS .......................................................................................................... 31
3.1
CONNECT YOUR W I-FI TO Q STATION ..................................................................... 31
3.2
INSTALL QLIGHT .................................................................................................... 31
3.3
LIGHT CONTROL .................................................................................................... 32
PLAY MUSIC & LIGHT SHOW .................................................................................. 34
-2-
BELLEDS Technologies. ---- Q Station User Guide
1 Introduction
Q Station (MB8800) is a product that can make the Q Bulbs blinking synchronously with
the rhythm of your music which is in your mobile. Just install the application called
“QLight” in your mobile. Then you can control the music play, the color of the Q Bulbs by
your mobile.
1.1 Verify Kit Contents
Q Station kit includes the following components. (Figure 1-1)
1.
Q Station
2.
Three Q Bulbs
3.
LAN cable
4.
Audio Cable
5.
Power Adapter
6.
QIG (Quick Installation Guide)
Figure 1-1 Q Station Package Contents
-3-
BELLEDS Technologies. ---- Q Station User Guide
1.2 Connection
Make sure the device and the cables are connected correctly. (Figure 1-2)
1. Plug in Power Adapter to Q Station.
2. Connect the Q Station to the LAN of your Home Router with LAN cable (optional).
(If you want to connect internet wirelessly, please refer to 2.2.3 Internet Connection.)
3. Connect the Audio Cable from your Q Station to the AUX of your stereo or speaker.
4. Make sure the indicator light of Q Station is blinking with red (left) and blue (right).
There’re 2 indicator lights. (Figure 1-3)
a. The left indicator light shows the Q Station status.
If the left indicator light blinks with red color, it shows the Q Station is in good
status.
b. The right indicator light shows the network status.
If it blinks with blue color, it shows you have not connected to internet.
If it stays blue color, no blink, it shows you have connected to internet.
5. Screw-in the Q Bulbs.
6. Match the Q Bulbs with Q Station
a. Light up the 3 Q Bulbs.
b. Press the Match Hole shortly with a needle. (Figure 1-3)
After about 20 seconds, the 3 Q Bulbs will blink with green color one by one.
(The Q Bulbs blink with green color shows the Q Bulbs have been matched
with Q Station.)
Notice:
If any Q Bulb did not blink with green color (stay at white color), please turn off the
Q Bulb. And then turn on it, press the Match Hole again. Then you will see the Q
Bulb blink with green color.
7. Reset:
If you want to reset Q-station, just press the Reset Hole with a needle for about 10
seconds. (Figure 1-3)
Until you see the blue light turns red color. Then loose.
Then the Q station has been reset successfully.
-4-
BELLEDS Technologies. ---- Q Station User Guide
Figure 1-2 Power up Q Station
-5-
BELLEDS Technologies. ---- Q Station User Guide
Figure 1-3 Two indicator lights and Reset, Match holes
-6-
BELLEDS Technologies. ---- Q Station User Guide
2 Configuration
You can set the Q Station Wi-Fi related configuration in PC or mobile.
The details are as below.
2.1 Enter configuration page
1. Connect your computer’s Wi-Fi to Q Station SSID. (Figure 2-1)
Notice: By default, Q Station SSID is “bellnetXXXXXX”. No Encryption.
(XXXXXX is the last 6 digit of your MAC).
2. Open the web browser and enter “http://172.16.0.1” (by default).
Press Enter key, the Q station configuration home page will appear. (Figure 2-2)
Figure 2-1 Connect your computer’s Wi-Fi to Q Station SSID (e.g.bellnetA07AF2).
Figure 2-2 Q Station configuration home page (English)
-7-
BELLEDS Technologies. ---- Q Station User Guide
2.2 Configuration in detail
2.2.1 Music Service
This function controls the speaker name in BellQ.
(The BellQ is one application in mobile that can make the Q Bulb synchronize with the
music.)
Notice:
By default, Q Station Speaker Name is “bellmusicXXXXXX”.
(XXXXXX is the last 6 digit of your MAC)
Click “Music Service”, to enter the management page (Figure 2-3).
Click “Back”, to go back to Q Station configuration home page (Figure 2-2).
Figure 2-3 Music Service screen
You can change the Server Name:
1. Input the Server Name which you want in the field. (Figure 2-4)
2. Click “Done” (Figure 2-5), after 10 seconds it will pop-up a window (Figure 2-6)
3. Click “OK”, and refresh the page. Then the Server Name has been changed
successfully. (Figure 2-7)
-8-
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-4 Input the Server Name you want in field
Figure 2-5 Click “Done”
-9-
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-6 After 10 seconds, it will pop-up a window.
Figure 2-7 Click OK and refresh the page. Then Server Name is changed successfully.
- 10 -
BELLEDS Technologies. ---- Q Station User Guide
2.2.2 Basic Settings
In this function, you can change the Q Station Wi-Fi SSID.
Also, you can set the encryption mode and password for the Wi-Fi.
Notice:
By default, Q Station SSID is “bellnetXXXXXX”. No Encryption.
(XXXXXX is the last 6 digit of your MAC)
Click “Basic Settings”, to enter the management page (Figure 2-8).
Click “Back”, to go back to Q Station configuration main page (Figure 2-2).
Figure 2-8 Basic Settings screen
Currently: The Wi-Fi SSID is bellnetA07FA2. Encryption Mode is NONE (no encryption).
You can change the Device Name (Known as Wi-Fi SSID):
1. Input the Device Name which you want in the field. (Figure 2-9)
2. Click “Done” (Figure 2-10), after 20 seconds, it will pop-up a window (Figure 2-11):
Please refresh the page or reconnect your device.
3. Click “OK”, then the Device Name has been changed successfully. (Figure 2-12)
Notice:
After you changed the Device Name (Q Station SSID in Wi-Fi), you need to
connect to your new Q Station SSID again in Wi-Fi.
- 11 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-9 Input the Device Name you want in field
Figure 2-10 Click “Done”
- 12 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-11 After 20 seconds, it will pop-up a window.
Figure 2-12 Click OK. The Device Name is changed successfully.
- 13 -
BELLEDS Technologies. ---- Q Station User Guide
In Security drop-down list, there’re 4 encryption modes: (Figure 2-13)
NONE; WPA; WPA2; WPA/WPA2.
You can change the Wi-Fi encryption mode:
1. Choose one encryption mode (e.g. WPA ) in Security drop-down list.
2. Input the Password, Confirm Password. (Figure 2-14).
(Notice: password should not be less than 8 characters.)
3. Click “Done” (Figure 2-15), after 20 seconds, it will pop-up a window (Figure 2-16):
Please refresh the page or reconnect your device.
4. Click “OK”, then the security mode has been changed successfully. (Figure 2-17)
Notice:
After you changed the Wi-Fi encryption mode and password, you need to
connect to Q Station again with your new password in Wi-Fi.
Figure 2-13 There’re 4 encryption modes:
- 14 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-14 Input the Password & Confirm Password
Figure 2-15 Click “Done”
- 15 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-16 After 20 seconds, it will pop-up a window.
Figure 2-17 Click OK. The security mode is changed successfully.
- 16 -
BELLEDS Technologies. ---- Q Station User Guide
2.2.3 Internet Connection
There’re 2 ways to make your Q Station connect to internet.
We suggest you to choose Wired Mode, as it is more stable.
1. Wired Mode.
Just connect Q Station (WAN interface) with your home router (LAN interface), using
Ethernet cable. (Figure 2-18)
Figure 2-18 Connect Q Station (WAN) with home router (LAN)
- 17 -
BELLEDS Technologies. ---- Q Station User Guide
2. Wireless Mode.
Click “Internet Connection”, to enter the screen. (Figure 2-19)
Notice:

By default, the wireless access is ON.
You can click OFF to close wireless access.

The page needs some time to search the nearby Wi-Fi SSIDs.
After a few seconds, it will display the nearby Wi-Fi SSIDs. (Figure 2-20)
Connect to the nearby Wi-Fi SSID:
a. Click the SSID which you want to connect to (e.g. BellTest).
Then it will pop-up a window to let you input the password for the SSID.
(Figure 2-21)
b. Input the password of the SSID, then click “OK” (Figure 2-22).
(If you don’t want to connect, then click “Cancel”.)
c. After 25 seconds (Figure 2-23), it will scan the SSIDs again (Figure 2-24).
d. After a few seconds, it displays all the nearby SSIDs again.
You’ll see “BellTest” has been connected (Figure 2-25).
Notice:
Once it is successfully connected to internet, the right indicator light should be a
steady blue color. Otherwise it will be blinking.
- 18 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-19 Scanning the nearby Wi-Fi SSIDs
Figure 2-20 The nearby Wi-Fi SSIDs
- 19 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-21 Click “BellTest”, it will pop-up a window.
Figure 2-22 Input the Wi-Fi password of “BellTest”
- 20 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-23 Wait for 25 seconds
Figure 2-24 Scanning for nearby Wi-Fi SSIDs again.
- 21 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-25 After a few seconds, Q Station displays all the nearby SSIDs again.
Then you’ll see BellTest has been connected successfully.
- 22 -
BELLEDS Technologies. ---- Q Station User Guide
2.2.4 Upgrade Firmware
You can upgrade the Q Station’s firmware in this function:
Click “Upgrade Firmware”, to enter the screen (Figure 2-26).
(If you don’t want to upgrade firmware, you can click “Back” to go back to configuration
main page.)
There’re 2 ways to upgrade firmware:

Upgrade by yourself

Auto Upgrade
Notice:

If you upgrade firmware by PC, support above 2 ways of upgrade.

If you upgrade firmware by mobile, only support Auto Upgrade.
To upgrade by yourself, please follow below steps:
1. Click “Browse”.
It will pop-up a window to let you select the firmware file in PC.
Choose the firmware file which you want to upgrade. (Figure 2-27)
2. Click “Open”, you can see the selected firmware file on page. (Figure 2-28)
3. Click “Upgrade Firmware”.
It will pop-up a window: File uploaded success! Continue to upgrade? (Figure 2-29).
4. Click “OK”, to proceed the upgrading. (Figure 2-30).
If you want to quit the upgrading, click Cancel.
5. When the process is 100%, refresh the page. (Figure 2-31).
The new firmware has been upgraded successfully.
- 23 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-26 Upgrade Firmware screen
Figure 2-27 Select the firmware file in PC
- 24 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-28 You can see the selected firmware file on page.
Figure 2-29 Click “Upgrade Firmware”, it will pop-up a window.
- 25 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-30 Click OK, upgrade will proceed.
- 26 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-31 When process is 100%, refresh the page. New Firmware has been upgraded.
To auto upgrade, please follow below steps:
1. In Upgrade Firmware screen (Figure 2-26), Click Auto Upgrade Firmware.
You will see at the bottom of screen, there’s a circle blinking. (Figure 2-32)
2. Then it will pop-up a window: File uploaded success! Continue to upgrade?
(Figure 2-33).
3. Click “OK”, to proceed the upgrading. (Figure 2-34).
If you want to quit the upgrading, click “取消”(Cancel).
4. When the process is 100%, refresh the page. (Figure 2-35)
The new firmware has been upgraded successfully.
Notice:
If you use “Auto Upgrade Firmware” in mobile, when the process is 100%, you need to
connect your mobile Wi-Fi to Q Station again. Then go to http://172.16.0.1, you will see
the Firmware has been upgraded.
- 27 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-32 Firmware is upgrading.
Figure 2-33 On the page, pop-up a window
- 28 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-34 Click OK, upgrade will proceed.
- 29 -
BELLEDS Technologies. ---- Q Station User Guide
Figure 2-35 When process is 100%, refresh the page. New Firmware has been upgraded.
- 30 -
BELLEDS Technologies. ---- Q Station User Guide
3 QLight in iOS
In this section, we’ll introduce how to use the “QLight” application in mobile.
3.1 Connect your Wi-Fi to Q Station
Change your Wi-Fi connection to “bellnetXXXXXX”, you will connect to Q Station.
(Figure 3-1)
Notice:
By default, Q Station SSID is “bellnetXXXXXX”. No Encryption.
(XXXXXX is the last 6 digit of your MAC)
Figure 3-1 Change your Wi-Fi connection to “bellnetXXXXXX”
3.2 Install QLight
Software:
1. Search the APP “QLight” in APPs store.
2. Download and run it.
- 31 -
BELLEDS Technologies. ---- Q Station User Guide
3.3 Light Control
Run QLight, first you will see QLight light control page. (Figure 3-2)
Figure 3-2 QLight light control page
Figure 3-3 On top right, “White” change to
“Color”

Click “ALL”: all your light control operation will control all three Q Bulbs.

Light Control:
1. Click ON or OFF to turn on or turn off the Q Bulbs.
2. Slide the little circle
3. Move the intensity bar
to adjust the color of light.
to adjust the brightness.
4. Click “White” on the top right, then Q Bulbs will change to white color. The little circle
will disappear. You cannot adjust the color of light now. And “White” will change to
“Color”. (Figure 3-3)
At the time, if you click “Color”, then the Q Bulb color will change to the color where
the little circle stays at. The little circle
will appear. You can adjust the color of light
again.

Music Sync Start/Stop: The lights in the Group Music will/won’t blink with music.
- 32 -
BELLEDS Technologies. ---- Q Station User Guide

Click “LIGHT A”/ “LIGHT B”/ “LIGHT C”: You can control the Q Bulbs separately.
(Figure 3-4, 3-5, 3-6)
On the top of the page, you can see light SN (e.g. MD1ACXXX00000XXX).

Light Control: Operation is same as above.

Click
: You will go to Q Station Configuration Page.
(For the details, please refer to 2.2 Configuration in detail.)
Figure 3-4 LIGHT A control page
Figure 3-5 LIGHT B control page
Figure 3-6 LIGHT C control page
- 33 -
BELLEDS Technologies. ---- Q Station User Guide
4 Play Music & Light Show

Steps:
1. Click the iOS built-in APP “Music”
to play music. (Figure 4-1)
2. Select a song, then play the song.
3. Swipe the screen to select speaker in AirPlay, choose “bellmusicXXXXXX” as your
speaker. (Figure 4-2)
Notice:

By default, Q Station Speaker Name is “bellmusicXXXXXX”.
(XXXXXX is the last 6 digit of your MAC)

AirPlay protocol allows you to stream music to the stereo or speaker which is
connected to the Q Station. And the Q Bulbs will blink synchronously with your music.
Figure 4-1 iOS built-in APP “Music”
Figure 4-2 Choose “bellmusicXXXXXX”
as your speaker
- 34 -
Download PDF