Functions Maintenance - Allstar Show Industries Inc.

Maintenance
Functions
Lamp Installation
Disconnect the unit from power. Open
the lens door by pulling the top of the
door pivot latch towards you. This will
allow the door to swing open, revealing
a lamp carriage assembly with a
lampholder and reflector mounted to the
platform.
To lamp the theatre fixture, Cat.
No. FR2TH, align the flanges
of the pre focus lamp with the
respective indentations of the
pre focus lampholder. Please
note the lamp flanges are
asymmetrical, and the large
lamp flange must align with
large socket indentation. After
alignment, press lamp down
by the ceramic base and twist
clockwise 90° until lamp locks in
position.
To lamp the television fixture,
Cat. No. FR2TV, release the
locking lever of the bipost
socket so the lever is parallel
to the extruded housing. Insert
the bipost lamp into the socket
until the lamp stops, then lock
the lever to the original position.
The socket should firmly hold
the lamp in position. Be sure
that the lever is completely
closed.
Close the lens door until latch engages.
NOTE
Please do not touch the quartz lamp envelope during installation. If this
occurs, clean the lamp with isopropyl (rubbing) alcohol and lint free,
clean cloth.
These Leviton fresnels are UL listed to 2000 watts. Any usage of higher
wattage lamps is improper usage of the fixture and voids any manufacturing
warranties. Please use only the lamps listed in the charts shown here.
Focusing
The Leviton fresnels have an
extremely wide focusing range, with
spot focus applications to 85' and ten
foot projected diameters at only 8' in
full flood focus. The focus system is
simple to operate and maintain.
The focusing is controlled on the right
side of the fixture, simply turn the
handle clockwise for flood focus and
counter clockwise for spot focus.
Beam Control
The fresnel spotlight is a soft focusing projector that may be framed to reduce
flare or direct the light through Leviton barn doors and top hats. The beam
may be further softened through wire scrims or filters. Color temperature may
be shifted with Leviton dichroic glass filters, or normal color medium.
The Leviton fresnels accept industry standard 10" x 10" accessories, allowing
the fixtures to accept automated color changers, liquid crystal strobe effects
and many other items.
Color
Lee Color Effect Filters are recommended for all filter applications. These
filters are available in over 175 colors, color corrections, and diffusion
selections. Lee Filters are available in both 21" x 4" sheets and 25' x 4' rolls.
LIMITED TWO YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of
anyone else that this product at the time of its sale by Leviton is free of defects
in materials and workmanship under normal and proper use for two years
from the purchase date. Levitonʼs only obligation is to correct such defects by
repair or replacement, at its option, if within such two year period the product is
returned prepaid, with proof of purchase date, and a description of the problem to
Leviton Manufacturing Co., Inc., Att: Service Department, 20497 SW Teton
Ave., Tualatin, Oregon 97062. All products returned to Leviton-NSI must have
factory authorization for return prior to shipping. The purchaser is responsible
for completing and mailing to Leviton, within 15 days of purchase, the warranty
registration card enclosed with each product. This warranty excludes and
there is disclaimed liability for labor for removal of this product or reinstallation.
This warranty is void if this product is installed improperly or in an improper
environment, overloaded, misused, opened, abused, or altered in any manner,
or is not used under normal operating conditions or not in accordance with any
labels or instructions. There are no other or implied warranties of any kind,
including merchantability and fitness for a particular purpose, but if any implied
warranty is required by the applicable jurisdiction, the duration of any such
implied warranty, including merchantability and fitness for a particular purpose,
is limited to two years. Leviton is not liable for incidental, indirect, special, or
consequential damages, including without limitation, damage to, or loss of use
of, any equipment, lost sales or profits or delay or failure to perform this warranty
obligation. The remedies provided herein are the exclusive remedies under this
warranty, whether based on contract, tort or otherwise.
Reflector
The reflector may be accessed by
opening the lens door. Remove
lamp to access reflector surface for
cleaning. The Alzak® finish requires
little maintenance, occasionally wipe
with isopropyl (rubbing) alcohol, and a
lint free cloth. Strong alcohol or acidic
cleaners MUST NOT be used.
Lens
The lens will become dirty due to
environmental conditions. To clean,
use a lint-free cloth and rubbing
alcohol. Do not use commercial
lens cleaners. If significant dirt and
grime exist, remove the lens from
the fixture and place lens in clean
water WITHOUT SOAP. Rinse
grime away, clean the reflector
with alcohol.
Recommended Lamps for 8” Theater Fresnel
Watts
Part
No.
2000
1500
1000
1000
2000
1000
1000
176-194
176-193
176-192
176-191
6994C
T-16
T-2
The tension is adjusted by turning
the center screw within the focus
handle while the fixture is aimed 90
degrees down, so the full weight of
the lampholder assembly bears on the
focus gear. Tighten the screw until the
assembly does not move. Do not over
tighten.
The focus gear should interface
smoothly with the rack on the focus
platform. To adjust, aim fixture to a
horizontal axis or place unit on a table.
Remove the focus handle. Loosen but do
not remove the screws on each side of
the focus gear. Reach inside the fixture
and move the socket assembly manually.
Adjust the focus gear so the assembly
is halfway between maximum possible
engagement into the rack and the point
where gears will slip. Tighten the two
screws when focus gear reaches that
point.
BVW
CWZ
BVV
BVT
Color
Temp.
Life
(Hrs.)
2000W, 250 hr., 3200°K, 120V
1500W, 325 hr., 3200°K, 120V
1000W, 200 hr., 3200°K, 120V
1000W, 500 hr., 3050°K, 120V
2000W, 400 hr., 3200°K, 220/240V
1000W, 750 hr., 3050°K, 220/240V
1000W, 200 hr., 3050°K, 220/240V
Recommended Lamps for 8” Television Fresnel
Watts
Part
No.
ANSI
Color
Temp.
2000
1500
1000
2000
650
176-075
176-157
176-161
476-055/056
476-048/049
CYX
CXZ
CYV
CP41
CP39
2000W, 200 hr., 3200°K, 120V
1500W, 300 hr., 3200°K, 120V
1000W, 200 hr., 3200°K, 120V
2000W, 200 hr., 3200°K, 220/240V
650W, 100 hr., 3200°K, 220/240V
Life
(Hrs.)
Accesories
Part No.
Description
000-A2KBD-000
000-A2KCF-000
000-A2KSS-000
000-A00CS-000
000-A2KTH-000
Eight leaf barn door
Diffusion frame
Set, single, half/single scrim
Combo stud for flat yoke
8" Top hat
Focus System
The rack and pinion focus system
can lose tension over long periods of
time by expansion and contraction of
the fixture housing and components,
or the gear itself could move causing
improper fitting against the cast rack.
Both items are easily resolved.
ANSI
8" THEATRE AND
TELEVISION FRESNELS
Photometric Performance
8" Theater Fresnel, Cat. No. FR2TH, with lamp No. 176-194, 2000W
ANSI Code BVW
USER GUIDE
For field diameter at any distance, multiply that distance by 0.269 for spot
and 1.238 for flood.
Beam Candlepower
Spot
Flood
358,000
37,000
8" Television Fresnel, Cat. No. FR2TV, with lamp No. 176-075, 2000W
ANSI Code CYX
For field diameter at any distance, multiply that distance by 0.265 for spot
and 1.32 for flood.
Beam Candlepower
Spot
Flood
Leviton Fresnels utilize the latest advances in lighting technology to
provide the best quality fixture in the market. This operating guide will help
you to become more familiar with your spotlight. The major components
of the fresnel are:
358,000
39,500
The focus assembly will grind against the
rack if engaged too deeply, and gears will
slip if adjustment is too high.
PK-93196-10-00-0A
1
2
3
4
The door assembly — Includes the lens door, accessory clips,
latch mechanism, safety latch and the fresnel lens.
The lamp carriage — Includes the lampholder, wiring, reflector and
the lampholder platform and associated parts.
The focus system — Includes the focus handle, pinion gear and
associated hardware.
The housing — Includes the extruded housing, cool focusing
handles, and simple, rugged design.
LAMP HOUSING ASSEMBLY
Ref.
Qty.
Description
1
1
2
Item Number
DOOR ASSEMBLY
Ref.
Qty.
Description
Upper right housing
40
1
Lens door assembly
1
Upper left housing
41
2
Screw, pan head, 6-32 x 1/2"
3
1
Lower right housing
42
1
Lock pin
4
1
Lower left housing
43
1
Latch handle
5
1
Top housing
44
1
Commpression spring
6
1
Focus track
45
1
Safety clip
7
1
Front cover
46
1
Retaining ring
8
1
Rear cover
47
1
Knob
9
1
Standoff disk
N00-HD237-690
48
1
K-lock nut, 6-32
10
3
Rivet, 3/16" x 11/16"
N00-HD913-400
49
1
Latch
11
1
Yoke
N00-SM281-330
50
1
Latch spring
12
1
Washer, flat
51
1
Washer, flat
13
1
Bolt, hex head, 1/4-20 x 1"
52
1
Screw, pan head, 6-32 x 1"
14
1
Screw, pan head, 10-24 x 1"
53
1
8" Fresne lens
N01-LE020-110
15
1
Focus handle
54
4
Lens fastener
N00-HD935-730
16
1
Washer, fibre
17
5
Screw, pan head, 8-32 x 3/4”
18
2
Wave washer
N00-HD223-440
19
1
Focus gear assembly
N01-SM280-570
20
13
K-lock nut, 8-32
21
2
Screw, pan head, 10-24 x 3/4”
22
1
Hinge
23
30
Screw, flat head, 8-32 x 1/2"
24
1
Ring terminal
25
1
Green wire
26
2
Washer, internal tooth, #8
27
1
Strain relief
28
1
Sleeving, 32" long
29
1
Black wire
30
1
White wire
31
1
Standoff disk
32
3
Rivet, 3/16" x 7/16"
33
1
Pressure disk
N00-SM243-380
34
1
T-bolt
N00-HD062-000
35
4
Screw, pan head, 6-32 x 3/8"
N00-HD020-800
36
1
Light shield
37
2
K-lock nut, 10-24
38
1
Tilt handle
39
2
Screw, pan head, 10-24 x 2"
70
1
C-clamp
N00-KN280-950
Item Number
70
N00-HD781-900
N00-SM237-550
Qty.
Description
55
4
Screw, pan head, 8-32 x 3/4"
56
1
Screw, pan head, 8-32 x 1/2"
57
1
Lampholder platform
58
4
Carriage assembly guide
59
1
Cable clamp
60
1
Mogul prefocus adapter
61
1
Adapter brace
62
1
Mogul prefocus socket
63
2
Washer, flat, #10
64
2
Screw, pan head, 10-24 x 1"
65
1
Shield
66
1
Reflector mount
67
4
Rivet, 1/8" x 1/4"
68
1
Reflector
68
36
20
35
13
12
38
10
9
2
23
11
14
15
16
PLATFORM ASSEMBLY — THEATER FRESNEL
Ref.
39
8
37
4
17
Item Number
7
18
5
67
68
6
64
20
63
21
N00-SM275-250
62
19
22
20
N01-SK020-260
42 43
N00-HD031-320
1
17
44
45
46
47
3
49
48
Description
Item Number
69
1
Lampholder
N00-AS282-310
54
40
26
23
N00-HD707-000
41
000-A00CC-000
Leviton NSI Division Headquarters
20497 SW Teton Avenue, Tualatin, OR 97062
28
24
PLATFORM ASSEMBLY — TELEVISION FRESNEL
Qty.
67
51
50
53
20
25
26
30
25
60
20
29
20
59
58
59
20
31
32
17
61
66
69
27
41
Ref.
66
65
20
58
33
34
57
57
23
56
55
23
56
55
52
Customer Service Telephone: 800.736.6682
Customer Service Fax: 503.404.5594
Technical Services: 800.959.6004
Leviton Manufacturing Company, Incorporated.
59-25 Little Neck Parkway, Little Neck, NY 11362-2591.
Visit Levitonʼs websites at http://www.nsicorp.com
& http://www.leviton.com
Copyright® 2003. Leviton Manufacturing Company, Inc. All Rights Reserved
Specifications and pricing subject to change at any time.
PK-93196-10-00-0A
FOLDING DIAGRAM
LEVITON INSTRUCTION SHEET/MANUAL
SPECIFICATIONS
PK-93196-10-00-0A
Black
Helvetica
20# White paper
Dull/Smooth finish TopKote
Paper size:
Overall size:
Final fold size:
25.75" X 11"
5.5" X 11"
DOCUMENTATION
EC
2/21/05