Pelican Work Lights Instruction Manual

Cat. #1920
PELICAN
TM
1920
LED
INSTRUCTION MANUAL
This compact flashlight produces an ultra bright light
beam by using a LED powered by (2) two AAA
1.5V alkaline batteries. The 1920 flashlight is
designed for easy use with one hand opera ion
and has a dual-switch mode for constant-on and
momentary-on. The 1920 flashlight body is made
by high precision CNC machines from
aircraft-grade aluminum alloy for the most durable
construction. The 1920 flashlight is water resistant.
TO INSERT BATTERIES
1. R
emove he tail cap by turning counter-clockwise.
2. Install (2) two AAA alkaline batteries with
+ terminal facing to the head assembly.
3. Replace the tail cap onto the flashlight
by turning clockwise until sealed.
OPERATION
High > Low > Off
1. MOMENTARY Gently depress he tail button for momentary
operation.
Press once for high, press again (within a half
second) to change from high to low.
2. CONSTANT ON • Single click for High
• Three clicks (no more than a half
second between clicks) for low
3. LIGHT-OFF Press the tail button to turn OFF.
TO CHANGE BATTERIES
1. R
emove the tail cap by turning
counter-clockwise until it comes off he
rear of the 1920 flashlight.
2. Remove the (2) two used batteries
from the 1920 flashlight.
3. Install he (2) two new AAA alkaline batteries
with + terminal facing to the head assembly.
4. Replace the tail cap by turning clockwise
until sealed.
GENERAL CARE AND MAINTENANCE
1. Clean o-rings with a soft clean cloth to insure that
sealing area is free of dirt that could destroy the o-ring
seal.
2. Apply a light coat of clear silicone grease on the o-rings
occasionally if turning action becomes too difficult.
3. Remove the tail cap and wipe the rear threads of the
1920 flashlight body and inside of the tail cap with a
soft clean cloth occasionally to avoid intermittent
flashlight operation.
CAUTION
To prevent the 1920 flashlight coming on
accidentally when the flashlight is stored, remove the
batteries. If the 1920 flashlight is turned on while it is in
a container, the flashlight can overheat and damage the
flashlight or the material of the surrounding area.
SPECIFICATIONS
BULB
Batteries
LED
(2) Two AAA alkaline or other
equivalent alkaline batteries
O-RING MAINTENANCE
Check closely for cuts, scratches, or otherwise damaged
o-ring or mating lens lip surface. Remove any dirt or foreign
matter from o-ring sealing surfaces. Keep threads, o-ring
groove and inside lip of lens lubricated with silicone grease.
See Warranty information for replacement of o-ring.
Battery Safety Information
WARNING: HANDLE AND STORE BATTERIES
PROPERLY TO AVOID INJURY OR DAMAGE
BATTERIES CAN BE DANGEROUS!
Most battery issues arise from improper handling of
batteries, and particularly from the use of damaged
or counterfeit batteries. Please review he information below to avoid serious injury and/or damage to
your property.
Alkaline Batteries
1. For those lights with hazardous location safety
approvals for explosive environments please
be advised that he safety approval is only valid
for he specified battery type manufacturer and,
where applicable, brand names hat are displayed
on the flashlight and/or instructions sheets that
are supplied wi h the light. The use of o her battery
technologies may reduce the performance of the
flashlight and will invalidate he safety approval.
2. Always read he battery manufacturers recommenda ions for the appropriate use of the battery
technology/brand prior to using the flashlight.
3. When replacing he batteries:
a. Replace all he batteries at the same time.
b. Do not mix battery brands and old and new
batteries.
c. Always insert batteries correctly wi h regard
to polarity (+ and -) marked on the battery
and equipment.
4. Do not change batteries in a hazardous location.
5. Remove batteries from equipment if it is not to be
used for an extended period of ime.
Always dispose of all batteries properly
at an approved battery recycling center.
Download PDF

advertising