LED Wall Pack
A traditional look with a brand
new engine.
- LED Magazine
7057 Marcelle St,
Paramount, CA 90723
800-640-0386
www.altechefficiency.com
sales@altechefficiency.com
Specifications
Model Number
DLC #
DLC Partner
AE-L-WPIS-90
U-IWP-90
Ultron Industries
Input Wattage
90W
Replacement Wattage
350W
Input Voltage Range
120-277V
Delivered Lumens
8614 LM
Lumen Efficiency
95 LM/W
Color Rendering Index (CRI)
70+
Color Temperature (Kelvin)
3000K-5700K
Beam Angle
120°
Power Factor
0.99
Frequency
MAX THD (%)
50/60Hz
15
Min. Ambient Temp
-30.0°F / -34.4℃
Max. Ambient Temp
130.0°F / 48.9℃
IP Rating
Dimming Compatible
IP65
3 in 1 dimming function (1˜10Vdc or PWM signal or resistance)
Product Weight
9.9LB / 4.5KG
Product Height
9.1” / 233mm
Product Length
13.0” / 332mm
Product Width
7.4” / 189mm
Lens
Materials
Glass
Die Cast Aluminum
Finish
Black (Default)
LM70 Life Time
100,000 Hours
UL/cUL
E481056
DesignLights Consortium®
YES
CE
YES
FCC
YES
Warranty
5 Years
Dimensions
User Guide
Note:
Please read this entire manual to fully understand and safely use the luminaire. The
products can be used at the voltage of 100-277V AC, 50/60HZ, suitable for indoor and
outdoor, moisture proof and dust proof. Specifications are subject to change without
notice. Please visit www.altechefficiency.com for the most recent product information.
Unpacking:
1. Unpack and carefully examine the product.
2. Report any damage and save all packing materials if any part(s) were damaged during shipping.
3. Do not attempt to use the fixture if it is damaged.
Before You install:
1. Before installing any light fixtures, read and understand all cautions, warnings, instructions and product
labels. Failure to do so can result in injury and/or void the warranty.
2. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
3. The product should be installed and operated by a qualified electrician or technician in accordance
with relevant local codes.
4. Risk of electric shock. Ensure that main power source is off when wiring or soldering the sections of
the product.
Maintenance:
1. This fixture is designed for years with minimum care. For optimum performance, periodically clean the
lens with a mild, non abrasive glass cleaner and soft cloth. DO NOT use solvents or cleaners
containing abrasive agents. When cleaning the fixture, make sure you have the power turned off and
do not spray liquid cleaner directly onto the LED, socket or wiring.
2. Disconnect the product from the power supply prior to cleaning.
3. Use a dry or slightly moistened cloth for cleaning.
4. Never use any chemicals or abrasive materials for cleaning.
Installation Instructions:
1. Loosen the screws on the side of the wall pack and open the fixture.
2. Remove the wire nuts connecting the driver to the LED board and disconnect
wires.
3. Remove the front of the fixture by lifting off the hinge.
4. Choose mounting hole option and remove respective mounting hole cover.
5. Screw on the cable gland that accompanied the fixture.
6. To shorten installation time, drill appropriate mounting holes in the back of the
fixture to align with exiting holes whenever possible.
7. Connect the input and ground wires of the fixture to the power supply. Brown
is live. Blue is neutral. Green/Yellow is ground. Wiring inside the fixture
is recommended.
8. Reattach front of fixture to the mounting hinges.
9. Reconnect the driver to the LED board with the provided wire nuts.
10.Close the fixture and secure the screws on the side of the fixture.