AI FP30-2B Combination Electric Fireplace Heater

LOT NUMBER:
DATE PURCHASED:
/
/
COMBINATION ELECTRIC FIREPLACE/HEATER
Model # FP30-2B
OPERATING INSTRUCTIONS
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to
the store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-877-494-2536 (English, French and Spanish)
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
(In US, Canada, and Mexico only)
Or visit our website www.baysidefurnishings.com
Or e-mail your request to parts@baysidefurnishings.com
PLEASE READ ALL OF THE INFORMATION IN THIS OPERATING MANUAL, INCLUDING ALL
SAFETY, OPERATING, AND MAINTENANCE INFORMATION. TO AVOID THE POTENTIAL RISK
OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, USERS SHOULD FOLLOW THE
DIRECTIONS AND WARNINGS IN THIS MANUAL.
Your Electric Fireplace / Heater is fully assembled from the factory. There are no installation steps
required to make the fireplace / heater work.
Date 2016-09-12 Rev. 0001-E Factory: ZHOPAI
E
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electrical shock and injury to persons, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If
provided, use handles when moving this heater. Keep combustible material, such as furniture,
pillows, bedding, papers, clothes and curtains at least 0.9 meters (3 feet) from the front of the
heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and
whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has
been dropped or damaged in any manner. Return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
Never locate heater where it may fall into a bathtub or other water container.
8. Do not run power cord under carpeting. Do not cover power cord with throw rugs, runners, or
the like. Do not route cord under furniture or appliances. Arrange power cord away from
traffic area and where it will not be tripped over.
9. To disconnect heater, turn controls to off, then remove plug from outlet.
10. Connect to properly grounded outlets only.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may
cause an electric shock or fire, or damage the heater.
12. To prevent a possible fire, do not block firebox air intakes or exhaust in any manner. Do not
operate firebox on soft surfaces, like a bed, where openings may become blocked.
13. A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline,
paint, or flammable liquids are used or stored.
14. There is a thermostat limiter inside the heater. When the inner temperature over heating or
occur abnormal heating, the thermostat protective device would cut off power supply to avoid
the fireplace damaged or risk of fire.
15. Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to persons.
16. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or
reloadable power tap (outlet/power strip).
There are no user serviceable parts inside the fireplace/heater. If the
unit appears to malfunction, turn the unit off and unplug the unit from the wall immediately,
then contact our Customer Service at 1-877-494-2536 for assistance, or refer service to
qualified service personnel.
While the heater is in use, the top center of the fireplace can get hot to the touch,
and may cause serious injury or burns. Always supervise small children around the
fireplace/heater. Do not place any cloth or decorations over the heater outlet of
CAUTION the fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may
cause a fire and serious injury may result.
HOT
SAVE THESE INSTRUCTIONS
2
E
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This product
is equipped with a cord having an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
This heater is for use on 120 volts circuit and has a
grounded plug that looks like the one illustrated on
Figure 1. See Figure 1 for grounding instruction. An
adapter as shown at C is available for connecting
three-blade grounding type plugs to two-slot
receptacles. The green grounding lug extending
from the adapter must be connected to a
permanent ground such as a properly grounded
outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
Figure 1
Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product – If
it will not fit the outlet; have a proper outlet installed by qualified electrician.
FCC/IC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operation.
Modifications not approved by the party responsible for compliance could void user’s authority to operate
the equipment.
CAN ICES-3 (B)/NMB-3(B).
This Class B digital apparatus complies with Canadian ICES-003.
3
E
OPERATION
The fireplace/heater unit comes in two distinct parts:
The fireplace unit itself, (Figure 2), and the Remote Control, (Figure 3).
ELECTRICAL
SPECIFICATIONS
Figure 2
Model No.
FP30-2B
Voltage
120 V
Frequency
60 Hz
Watts
1500 W
Figure 3
• The Fireplace/Heater Unit
On the top left corner of the fireplace/heater unit is the control panel. This panel contains the buttons and
displays to properly operate the fireplace/heater unit. Refer to Figure 4 for placement of the control
buttons.
Fireplace/Heater Front
Panel Controls
1. Display Unit
2. Function Indicator
3. Timer Function
4. Heater Control
5. Flames Control
Figure 4
6. Main Power
The far left segment, (1), is a Display Unit. This segment will show information about flame level, timer,
and current Fahrenheit/Centigrade temperature.
4
E
OPERATION
The next segment, (2), is a Function Indicator. It has three square LED’s, a red one, a green one and a
blue one. The red LED indicates that the Fahrenheit temperature heating function is running, the green
LED indicates that the Centigrade temperature heating function is running, and the blue LED indicates that
the Timer Function is engaged. And on the right of the three LED’s, there is an infrared receiver module;
you can aim at the position to control the heater by the remote control.
The next segment, (3), is a button for activating the Timer Function. You activate the timer by pressing the
button multiple times to get the amount of time you want the fireplace/heater to run. The timer button
operates both the flames and the heater function. If the heater is operating when the timer is set, then the
heater is on the timer. If the flames are operating, then the timer will control the flames. If both the heater
and flames are operating with the timer is set, then the timer controls both the flames and the heater.
Pressing the button in sequence will set the timer for a set interval. This interval period is shown in the
display segment, (1), in blue. The set intervals are as follows:
BUTTON PRESS
1st press
2nd press
3rd press
4th press
5th press
6th press
7th press
8th press
TIMER INTERVAL
30 Minute Interval
1 hour
2 hour
3 hour
4 hour
5 hour
6 hour
OFF
DISPLAY VALUE
30
1h
2h
3h
4h
5h
6h
NONE
The timer interval is set from the time the interval is selected. There is no clock function for turning the
heater or flames on or off at a specific time.
The next segment, (4), Heater Control, is a power button for the heater. The selected functions are on or
off. There is no speed setting for the heater blower. If the heater is on when the unit is turned off by the
Main Power button, when the power is turned back on, the heater will come on at the same time. If the
heater is off when Main Power is turned off, the heater will remain off when Main Power is turned back on.
When the heating function turns on, you can press and hold this button 5 seconds to enter temperature
adjustment mode. The LED’s indicator is red. In adjustment mode, the Display Unit will flash (interval is 0.5
second). There are 22 levels to change Fahrenheit temperature 72℉―73℉…82℉―ON—62℉―63℉…71℉.
After set, the Display Unit will flash 5 times and will exit from setting status. After turning on the Display
Unit, if nothing happens within 10 seconds, it will turn off the show.
And when the heating function turns on, you can press and hold Main Power button 5 seconds to enter
temperature converting mode. The LED’s indicator is green. In this converting mode, the Display Unit will
flash (interval is 0.5 second). There are 12 levels to change Centigrade temperature
22℃―23℃…27℃―ON ―17℃―18…21℃. After set, the Display Unit will flash 5 times and will exit from
setting status too. After turning on the Display Unit, if nothing happens within 10 seconds, it will turn off
the show, too.
To lock the heating function, with the main power button on, press and hold the heater button (4) for ten
seconds. The log lights flash six times to indicate that the heater function is locked. In this mode, there is
no heating function but only glowing logs.
To unlock the heating function, press and hold the heater button (4) for ten seconds. The log lights flash
six times and then enter heating function mode.
5
E
OPERATION
The next segment, (5), is the Flames Control button. Like the timer button, there are four settings for the
flames. Pressing the flames button in sequence will set the flames for different levels of flame height.
These flame levels are showed in the display segment (1). The flame settings are as follows:
BUTTON PRESS
FLAME LEVEL
DISPLAY VALUE
FIREPLACE SHOWS
1st press
High
L8
Amber Flames and Logs Glow Highest
2nd press
Medium
L7
Amber Flames and Logs Glow Medium
3rd press
Low
L6
4th press
High
L5
5th press
Medium
L4
6th press
Low
L3
7th press
Amber Flames and Logs Glow Low
Amber Flames and Logs Glow Highest
with Blue Flames
Amber Flames and Logs Glow Medium
with Blue Flames
Amber Flames and Logs Glow Low
with Blue Flames
L2
Color Rotation
Flames Off, Logs Glow Highest
8th press
Flames Off
L1
9th press
All Off
None
Flames Off, Logs Off
Regardless of the flame setting when powered off by the Main Power button, the flames will come on in L8
mode, (High), when the power is turned back on by the Main Power button.
There is locking function also about the Flames Control button. When the flame is in L8 mode, pressing and
holding this button for 5 seconds, the logs lights flash 6 times, it indicates that the flame function is locked.
In this mode, there are no flames but only logs glowing. Pressing the Flames Button in sequence will set
the logs for different levels of logs brightness. These logs brightness shows in the display segment (1). The
logs settings are as follows:
BUTTON PRESS
FLAME LEVEL
DISPLAY VALUE
FIREPLACE SHOWS
1st press
Flames Off
L4
Logs Glow Brightest
press
Flames Off
L3
Logs Glow Medium
3rd press
Flames Off
L2
Logs Glow Low
4th press
Flames Off
L1
Logs Glow Brightest
5th press
All Off
None
Logs Off
nd
2
Anew pressing and holding this button 5 seconds, this mode will be unlocked after 6 timers logs lights flash,
and then both flame lights and logs lights will be on.
The last segment of the control panel, (6), is the Main Power button. As the name infers, the Main Power
button controls the overall power to the fireplace/heater unit. Pressing the button once turns power on to
the entire unit, and pressing the button again will turn power off to the entire unit. If you find that none of
the other buttons appear to work, check to make sure that Main Power is turned on to the unit.
6
E
OPERATION
• The Fireplace/Heater Remote Control
A great feature of the Fireplace/Heater unit is the small remote control. This remote combines all the
functions of the front panel controls of the fireplace/heater with the convenience of not having to leave the
comfort of your seat to change the settings of the fireplace/heater.
Follow the steps below to install the batteries into the remote control.
1. Press down and slide back cover off the battery compartment.
2. Insert two provided AAA batteries into the battery compartment making sure that the ends of the
batteries with the negative (-) symbols are against the springs in the battery compartment.
3. Replace the battery compartment cover.
4. Turn the remote over and aim it towards the fireplace/heater unit.
5. Press the upper center power button, and see if the flames on the fireplace/heater turn on or off.
6. If nothing appears to happen, check to make sure the battery is installed correctly, and try again.
Figure 5
• Battery Replacement
NOTE: Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable (nicad, nimh, etc.) batteries.
Do not ingest batteries.
1.
2.
3.
4.
Non-rechargeable batteries are not to be recharged.
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the product.
Always purchase the correct size and grade of battery
most suitable for the intended use.
5. Replace all batteries of a set at the same time.
6. Clean the battery contacts and also those of the device
prior to battery installation.
7. Remove batteries from equipment with is not to be used
for an extended period of time.
7
NOTE:
Battery disposal
Please always dispose of batteries
at a suitable recycling point.
E
• Remote Control Button Functions
The remote control mimics the buttons on the front panel of the fireplace/heater. The remote control
does not have a display function. The buttons on the remote control work as follows: (Figure 6)
Heater Up
Main Power
Timer Function
Flames Control
Heater Down
Heater Control
Figure 6
These remote control buttons work exactly the same as the buttons on the front panel of the
fireplace/heater. See the FIREPLACE/HEATER section above to review the front panel button functions, and
familiarize yourself with the remote control.
NOTE: The remote control only can carry on the simple functional operation to the product, but it has no
function to lock/unlock the flame and heating function, and it cannot be used to convert the Fahrenheit
and Centigrade temperature, too.
The Fireplace/Heater is now ready for you to enjoy for many years to come.
8
E
TROUBLE SHOOTING GUIDE
PROBLEM
1. No power or function.
SOLUTION
1a. Check that unit is plugged into a standard
120V outlet.
1b. Press power button on the control panel.
2. Main power switch lights up, but no flame
effect.
3. Have flame effect, but heater does not blow
warm air.
2a. Open the top and back panel to check if the
flame spindle has fallen off from spindle motor.
3a. Confirm temperature setting exceeds room
temperature.
3b. Try to turn on/off HEATER button several
times to make sure it is in the “ON” position.
4. Heater does not work, but Power and
Heater switches are in the “ON” position and
thermostat is set on “HI”.
4a. Turn all switches to the “OFF” position and
unplug the unit from the wall outlet for 5
minutes. After 5 minutes plug the unit back into
wall outlet, and operate as normal.
5. The display unit on the control panel shows
“88” and the function indicator is quick
flashing, indicating it is in alarm mode.
5a. Unplug the unit from the wall outlet for 5
minutes. After 5 minutes plug the unit back into
wall outlet, and operate as normal.
6a. Change the remote batteries.
6. Remote Control is not working.
6b. Operate remote transmitter at a slow
measured pace. Press the remote control buttons
with an even motion and gentle pressure.
Repeatedly pressing buttons in rapid succession
may cause the transmitter to malfunction.
For assistance, call customer service: 1-877-494-2536.
9
E
CARE & MAINTENANCE INSTRUCTIONS
The blower motor and flame motor are pre-lubricated for a durable using time and need no further
lubrication or maintenance. To remove any accumulation of dust or fluff the soft brush attachment of a
vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater.
Use a soft, clean cloth that will not scratch the surface when dusting.
Use a clean soft cloth dampened with warm water to clean the fireplace surface. DO NOT use household
or abrasive cleaners, as these products may damage the surface.
When cleaning the glass viewing screen use a non-abrasive damp cloth with liquid cleaner or soft soap
if necessary; DO NOT use cleaning powders or any other substance with abrasives since these
substances will scratch glass.
Under no circumstances should this product be operated with a broken or chipped glass panel.
Do not strike or slam the glass.
In the event that your appliance is stained or otherwise damaged during use, we recommend that you
call a professional to repair your furniture.
When not in use please unplug the cord from the outlet to prevent any damage or accidental plug of the cord.
ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER.
FIRST TURN OFF THE MAIN POWER. THEN REMOVE THE ELECTRICAL PLUG FROM THE WALL OUTLET.
DO NOT USE THIS FIREPLACE INSERT IF ANY PART OF IT HAS BEEN UNDER WATER.
IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE FIREBOX AND REPLACE ANY
PART OF THE ELECTRICAL SYSTEM WHICH HAS BEEN UNDER WATER.
We hope you enjoy your purchase for many years,
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Bayside Furnishings® purchase.
Should this product be defective in workmanship or materials, or fail under normal use, we will repair or
replace it for a period of up to one (1) year from date of purchase. Every Bayside Furnishings® product is
designed to meet your highest expectations. We guarantee that you will immediately see the value of our
fine furniture.
This warranty gives you specific rights and you may also have other rights, which vary from state to state
and province to province.
Customer Service: 1-877-494-2536
8:30 A.M. to 4:30 P.M., Pacific Time, Monday to Friday
www.baysidefurnishings.com
MADE IN CHINA / FABRIQUÉ EN CHINE / HECHO EN CHINA
10
E