SINGLE OVEN GAS RANGE
for residential use only
Models:
VEFSGG 365 N..
• USERS OPERATING INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
IMPORTANT - PLEASE READ AND FOLLOW
✓ Before beginning, please read these instructions completely and carefully.
✓ Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.
✓ Please observe all local and national codes and ordinances.
✓ Please ensure that this product is properly grounded.
✓ The installer should leave these instructions with the consumer who should retain
for local inspector’s use and for future reference.
✓ The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance
with the National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN
CANADA: Installation must be in accordance with the current CAN/CGA-B149.1 National
Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform
with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280
[formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD
(Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas
stream for safety and ease of service.
If an external electrical source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
national Electrical Code, ANSI/NFPA 70.
This range is supplied with a protective film on steel and aluminium parts.
This film must be removed before installing/using the appliance.
THIS RANGE IS FOR RESIDENTIAL USE ONLY
WARNING
• ALL RANGES CAN TIP
• INJURY TO PERSON COULD RESULT
• INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE
• SEE INSTALLATION INSTRUCTIONS
WARNING
NEVER use this appliance as a space heater to heat or warm the
room. Doing so may result in carbon monoxide poisoning and
overheating of the oven.
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT
FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
✓Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
✓WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• lmmediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• lf you cannot reach your gas supplier, call the fire department.
✓Installation and service must be performed by a qualified installer,
service agency, or the gas supplier.
2
Dear Customer,
Thank you for having purchased and given your preference to our
product.
The safety precautions and recommendations reported below are for
your own safety and that of others. They will also provide a means by
which to make full use of the features offered by your appliance.
Please preserve this booklet carefully. It may be useful in future, either
to yourself or to others in the event that doubts should arise relating to
its operation.
This appliance must be used only for the task it has explicitly been
designed for, that is for cooking foodstuffs. Any other form of usage is
to be considered as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the event of damage
caused by improper, incorrect or illogical use of the appliance.
WARNING!
The Governor of California is required to publish a list of substances known to the state of California to cause cancer or reproductive harm and requires businesses to warn customers of potential exposures to such substances.
WARNING!: Gas appliances contain or produce substances which can cause death or serious illness and which are known to the
State of California to cause cancer, birth defects or other reproductive harm.
To reduce the risk from substances in fuel or from fuel combustion, make sure this appliance is installed, operated, and maintained
according to the manufacturer’s instructions.
This appliance is designed and manufactured solely for the cooking of domestic (household)
food and in not suitable for any none domestic application and therefore should not be used
in a commercial environmement.
The appliance guarantee will be void if the appliance is used within a none domestic
environnement i.e. a semi commercial, commercial or communal environment.
3
USER INSTRUCTIONS
GENERAL INFORMATION
WARNING!!
1.This appliance shall not be used for space heating. This information is based on safety considerations.
ELECTRICAL GROUNDING INSTRUCTIONS
2.AlI openings in the wall behind the appliance and in the floor
under the appliance shall be sealed.
The range must be electrically grounded in accordance
with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA No. 70-latest edition.
Installation should be made by a Iicensed electrician.
3.Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
4.Do not obstruct the flow of combustion and ventilation air.
If an external electrical source is utilized, the installation must
be electrically grounded in accordance with local codes or, in
the absence of local codes, with the national Electrical Code,
ANSI/NFPA 70.
5.Disconnect the electrical supply to the appliance before servicing.
6.When removing appliance for cleaning and/or service;
A. Shut off gas at main supply.
B. Disconnect AC power supply.
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the range by pulling outward.
CAUTION: Range is heavy; use care in handling.
7. Electrical Requirement
Electrical installation should comply with national and local
codes.
8. Air Supply and Ventilation
The installer must refers to local/national codes.
9. Gas Manifold Pressure
Natural gas - 4.0” W.C.P.
LP/Propane - 11.0” W.C.P.
10. The misuse of oven door (e.g. stepping, sitting, or leaning
on them) can result in potential hazards and/or injuries.
11. When installing or removing the range for service, a rolling
lift jack should be used. Do not push against any of the
edges of the range in an attempt to slide it into or out of the
installation. Pushing or pulling a range (rather than using
a lift jack) also increases the possibility of bending the leg
spindles or the internal coupling connectors.
4
WARNING!!
This appliance is equipped with a three-prong grounding
plug for your protection against shock hazard and should be
plugged directly into a properly grounded socket.
Do not under any circumstances cut or remove the third
(ground) prong from the power plug.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing
service on the range. Replacement parts are available from
factory authorized parts distributors. Contact the nearest parts
distributor in your area.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should
not be left around within easy reach of children, as these may cause serious injuries.
The packaging material is recyclable and is marked with the recycling symbol
.
✓ Do not attempt to modify the technical characteristics of the appliance as this may
become dangerous to use.
✓ Do not carry out cleaning or maintenance operations on the appliance without having
previously disconnected it from the electric power supply.
✓ After use, ensure that the knobs are in
OFF
position.
✓ Do not allow children or other incapable people to use the appliance without supervision.
✓ During and after use of the range, certain parts will become very hot. Do not touch hot
parts.
✓ Keep children away from the range when it is in use.
✓ This range is supplied with a protective film on steel and aluminium parts. This film must
be removed before installing/using the appliance.
✓ Fire risk! Do not store flammable material in the oven, and in the storage compartment.
✓ Make sure that electrical cables connecting other appliances in the proximity of the
range cannot come into contact with the hob or become entrapped in the oven door.
✓ Do not line the oven walls with aluminium foil. Do not place shelves, broiler pan, pans or
other cooking utensils on the base of the oven chamber.
✓ The manufacturer declines all liability for injury to persons or damage to property caused
by incorrect or improper use of the appliance.
✓ To avoid any possible hazard, the appliance must be installed by qualified personnel
only. Any repairs by unqualified persons may result in electric shock or short circuit.
In order to avoid possible injuries to your body or to the appliance, do not attempt any
repairs by yourself. Such work should be carried out by qualified service personnel only.
✓ Danger of burns! The oven and cooking accessories may become very hot during operation. Make sure children are kept out of reach and warn them accordingly. To avoid
burns use kitchen clothes and gloves when handling hot parts or utensils.
✓ Stand away from the range when opening oven door. Hot air or steam which escapes
can cause burns to hands, face, and/or eyes.
✓ Never clean the range, oven and storage compartment with a high-pressure steam
cleaning device, as it may provoke a short circuit.
✓ This appliance is intended for use in your household. Never use the appliance for any
other purpose!
✓ If you should decide not to use this appliance any longer (or decide to substitute an
older model), before disposing of it, it is recommended that it be made inoperative in an
appropriate manner in accordance to health and environmental protection regulations,
ensuring in particular that all potentially hazardous parts be made harmless, especially in
relation to children who could play with old appliances.
Remove the door and the storage compartment pivoting panel before disposal to prevent entrapment.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR
USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental rules.
In particular:
✓ Never touch the appliance with wet hands or feet;
✓ Do not operate the appliance barefooted;
✓ Do not allow children or disabled people to use the appliance without your supervision.
The manufacturer cannot be held responsible for any damages caused by improper, incorrect
or unreasonable use of the appliance.
5
features

Island trim fitted
Backguard fitted
WARNING - VERY IMPORTANT NOTICE
Never obstruct the slots on the backguard / island trim.
1
1
3
2
Fig. 1.1
COOKING HOB
1. Semi-rapid burner (SR) - 6000 BTU/hr
2. Triple-ring burner (TR) - 12000 BTU/hr 3. Dual burner (D) - 16000 BTU/hr (Natural gas),
15000 BTU/hr (LP/Propane) Note:
-The electric gas-lighting device is incorporated into the
knobs.
- The appliance has a safety valve system fitted, the flow of
gas will be stopped if and when the flame should accidentally go out.
CAUTION:
If the burner is accidentally extinguished, turn the gas
off at the control knob and wait at least 1 minute before
attempting to relight.
CAUTION:
Gas appliances produce heat and humidity in the environment in which they are installed.
Ensure that the cooking area is well ventilated following
national/local codes.
6
2

Fig. 1.2
7
6
1
2
3
4
5
9
8
CONTROLS DESCRIPTION
1. Front left burner (2) control knob
2. Rear left burner (1) control knob
3. Central dual burner (3) control knob
4. Rear right burner (1) control knob
5. Front right burner (2) control knob
6. Oven light & fan control knob
7. Gas oven/gas broil control knob
8. Cooling fan failure warning light
9. 60’ alarm knob
When the cooling fan failure warning light is OFF the cooling fan
motor is correctly operating.
The burners of the cooking hob and the
gas oven can be used.
When the cooling fan failure warning light is lighted this indicates
the malfunctioning of the cooling fan motor.
The gas oven cannot be used.
Only the burners of the cooking hob
can be used.
Operate the cooking hob
burners and the oven as
per instruction manual.
Contact the After-Sales
Service.
SERVICE
7

how to use the top burners
GAS BURNERS (Semi-rapid and triple ring)
Gas flow to the burners is adjusted by turning the knobs (illustrated in fig. 2.1) which
control the valves.
Turning the knob so that the symbols printed on itself point to the symbol printed on
the control panel achieves the following functions:
Knob
position
Function
SEMI-RAPID burner
TRIPLE RING burner
closed
valve
maximum
rate
Fig. 2.1
minimum
rate
The maximum aperture position permits rapid boiling of liquids, whereas the minimum
aperture position allows simmer warming of food or maintaining boiling conditions of
liquids.
To reduce the gas flow to minimum, rotate the knob further anti-clockwise to point the
indicator towards the
position.
Other intermediate operating adjustments can be achieved by positioning the
indicator between the maximum and minimum aperture positions, and never between
the maximum aperture and
positions.
Fig. 2.2
N.B. When the range is not being used, set the gas knobs to their
positions
and also close the gas shut-off valve placed on the main gas supply line.
8

LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE
SAFETY DEVICE (Semi-rapid and triple ring)
In order to light the burner, you must:
1 – Push and turn the knob in an anti-clockwise direction up to the
position
(maximum rate), push in and hold the knob until the flame has been lit (fig. 2.2).
The sparks produced by the lighter situated inside the relative burner will light the
flame.
In the event that the local gas supply conditions makes it difficult to light the burner
in
position, try again with the knob in
position.
If there is no mains electrical supply, bring a lighted match close to the burner.
2 – Wait for about ten seconds after the gas burner has been lit before letting go the
knob (safety device activation delay).
3 – Adjust the gas valve to the desired position.
If the burner flame should go out for some reason, the safety valve will automatically
stop the gas flow.
To re-light the burner, return the knob to the closed
position, wait for at least 1
minute and then repeat the lighting procedure.
If your local gas supply makes it difficult to light the burner with the knob set to maximum, set the knob to minimum and repeat the operation.
Caution!
The range becomes very hot during operation.
Keep children well out of reach.
9

GAS BURNERS (Dual)
The Dual Burner is a very flexible burner which allows different regulations and optimal
cooking.
It is composed by one inner and two outer crowns; the flame of the inner crown can be
regulated separately from the flames of the outer crowns.
The Dual Burner can be used:
- as a small burner (flame produced only by the inner crown) which can be adjusted
from the maximum (
) to the minimum (
) position. Intermediate operating adjustments can be achieved by positioning the indicator between the maximum
and minimum opening positions, and never between the maximum opening and
position.
-as a high-power burner (all flames produced simultaneously by inner and outer
crowns) which can be adjusted from the maximum (
) to the minimum (
)
position.
Gas flow to the burner is adjusted by turning the knob (illustrated in fig. 2.3) which
controls the valve.
Turning the knob so that the symbols printed on itself point to the symbol printed on
the control panel achieves the following functions:
Knob
position
Function
closed
valve
Fig. 2.3
�
maximum rate
of inner crown
(only inner flame
at the maximum)
minimum rate
of inner crown
(only inner flame
at the minimum)
Fig. 2.4
maximum rate of
inner + outer crowns
(inside and outside
flames in
simultaneously
at the maximum)
minimum rate of
inner + outer crowns
(inside and outside
flames in
simultaneously
at the minimum)
10
DUAL burner

LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE
SAFETY DEVICE (Dual Burner)
In order to light the burner, you must:
1 – Push and turn the knob in an anti-clockwise (fig. 2.4) direction up to the
position (maximum rate of inner crown); push in and hold the knob until the flame
has been lit.
The sparks produced by the lighter situated inside the relative burner will light the
flame.
In the event that the local gas supply conditions makes it difficult to light the burner
in
position, try again with the knob in
position.
If there is no mains electrical supply connection, bring a lighted match close to the
burner.
2 – Wait for about ten seconds after the gas burner has been lit before letting go the
knob (safety device activation delay).
2 – Adjust the gas valve to the desired position.
If the burner flame should go out for some reason, the safety valve will automatically
stop the gas flow.
To re-light the burner, return the knob to the closed position (
), wait for at least 1
minute and then repeat the lighting procedure.
N.B. When the range is not being used, set the gas knobs to their
positions
and also close the gas shut-off valve placed on the main gas supply line.
CAUTION!
The range becomes very hot during operation. Keep children well out of reach.
11

CHOICE OF BURNER
(fig. 2.5)
The symbols printed on the panel above the gas knobs indicate the correspondence
between the knob and the burner.
The most suitable burner is to be chosen according to the diameter and volume capacity of the container to be warmed.
It is important that the diameter of the pots or pans suitably match the heating potential
of the burners in order not to jeopardise the efficiency of the burners, bringing about a
waste of gas fuel.
A small diameter pot or pan placed on a large burner does not necessarily mean that
boiling conditions are reached quicker.
Fig. 2.5
DIAMETERS OF PANS WHICH MAY BE USED ON THE HOB BURNERS
BURNER
MINIMUM
MAXIMUM
Semi-rapid
16 cm (6” 19/64)
24 cm (9” 7/16)
Triple-ring
26 cm (10” 3/16)
28 cm (11” 1/16)
Dual
26 cm (10” 3/16)
28 cm (11” 1/16)
Wok pans max 36 cm (14” 3/16)
Do not use pans with concave or convex bases
WRONG
CORRECT USE OF DUAL BURNER
(Fig. 2.6a - 2.6b)
The flat-bottomed pans are to be placed directly onto the pan-support.
When using a WOK you need to place the supplied stand in the burner to avoid any
faulty operation of the dual burner (Figs. 2.6a - 2.6b).
Fig. 2.6a
IMPORTANT:
The special grille for wok pans (fig. 2.6b) MUST BE PLACED ONLY over the pan-rest
for the dual burner.
CORRECT
Fig. 2.6b
Make sure that the handles of
cookware do not stick out over the
edge of the range, to avoid them
being knocked over by accident.
This also makes it more difficult
for children to reach the cooking
vessels.
12
how to use the gas oven
GENERAL FEATURES
The gas oven is provided with:
a) Oven burner, mounted on the lower part of the oven (21000 BTU/hr).
b) Broil burner, mounted on the upper part of the oven (15000 BTU/hr).
c)Fan motor which can be used in combination with the oven burner or separately
(without heating). It is not possible to use the fan motor in combination with
the broil burner: a safety device switches off the fan motor when the gas
oven/broil control knob is turned on broil position.

Attention: the range becomes
very hot during operation.
Attention: the oven door becomes
very hot during operation.
Keep children away.
WARNING:
The door is hot, use the handle.
d)Light that illuminates the oven to enable visually controlling the food that is
cooking.
OPERATING PRINCIPLES
Heating and cooking are obtained in the following ways:
a. by normal convection
The heat is produced by the oven burner.
N.B. When the range is not being
used, set the gas knobs to their
positions and also close the
gas shut-off valve placed on the
main gas supply line.
c. by forced convection
The heat produced by the oven burner is distributed throughout the oven by
the fan. The hot air envelops the food in the oven, provoking a complete and
rapid cooking.
It is possible to cook several dishes simultaneously.
d. by radiation
The heat is irradiated by the infra red broil burner.
f. by ventilation (this is not a cooking function)
The food is defrosted by using the fan only without oven burner.
VERY IMPORTANT
The oven/broil shall be used
always with the oven door closed.
USING THE OVEN FOR THE FIRST TIME
It is advised to follow these instructions:
– Furnish the interior of the oven by placing the wire racks as described at chapter
“Cleaning and maintenance”.
– Insert shelves and tray.
– Turn the oven on to the maximum temperature (position
) to eliminate
possible traces of grease from the oven burner. The same operation should be
followed for broil burner.
– Switch off the electrical supply, let the oven cool down, then clean the interior
of the oven with cloth soaked in water and detergent (neutral) then dry carefully.
Do not use
1st STEP
Broiling level
2nd STEP
Oven cooking level
3rd STEP
Oven cooking level
4th STEP
13

OVEN BURNER
It carries out normal “oven cooking”.
The gas flow to the burner is regulated by a thermostat which allow to maintain the
oven temperature constant.
The control of the temperature is assured by a thermostatic probe positioned inside
the oven.
The probe must be always kept in its housing, in a clean condition, as an incorrect position or encrustment may cause an alteration in the control of the temperature.
OVEN THERMOSTAT
The numbers printed on the control knob (fig. 3.1) indicate the increasing oven temperature value (see temperature table near the control knob - fig. 3.1).
Left column of the temperature table refers to oven burner used in combination with
the fan motor while right column refers to oven burner used in the normal convection
mode (without fan motor).
To regulate the temperature, set the chosen number onto the control panel indicator.
The position
serves only to turn on the broil burner.
Fig. 3.1
OVEN LIGHT AND FAN MOTOR
The oven light and the fan motor are controlled by a switch knob on the control panel
(fig. 3.2). To light up the oven lamp turn the knob anti-clockwise to
position.
To operate the fan motor turn the knob clockwise to
position.
In this setting also the oven lamp is lighted.
WARNING: The switch knob can be turned only clockwise from
position and anti-clockwise from
to
position.
The switch knob DO NOT TURN from
to
to
position. DO NOT FORCE.
IMPORTANT NOTE: The fan motor can be used in combination only with the oven
burner. A safety device switches off the fan motor when the gas oven/broil control knob
is turned on
position.
OK
Fig. 3.2
14
OK
NOT TURN

IGNITION OF THE OVEN BURNER
IMPORTANT NOTE: during ignition of the oven burner the fan motor shall be
switched off (light and fan control knob in
position - Fig. 3.2).
The thermostat allows the automatic control of the temperature.
The gas delivery to the oven burner is controlled by a two way thermostatic tap (oven
and broil burners) with flame-failure device.
To light the oven burner operate as follows:
1) Open the oven door to its full extent.
WARNING: Risk of explosion! The oven door must be open during this operation.
Fig. 3.3
2) Press the oven control knob right down and turn counter-clockwise (fig. 3.3) to max
position .
3) Check the oven burner has lit; if not, turn the knob clockwise back to OFF and repeat
the procedure from step 2.
4) Once the oven burner has lit, close the oven door slowly and adjust the burner
according to the power required.
If the flame extinguishes for any reason, the safety valve will automatically shut off the
gas supply to the burner.
To re-light the burner, first turn the oven control knob to position
, wait for at least
1 minute and then repeat the lighting procedure.
Attention: the oven door becomes
very hot during operation.
Keep children away.
VERY IMPORTANT NOTE: THE BURNER IGNITION PROCEDURE MUST ALWAYS
START WITH THE CONTROL KNOB IN THE OFF POSITION OR IT WILL NOT BE
POSSIBLE TO IGNITE THE BURNER.
TRADITIONAL BAKING (OVEN BURNER WITHOUT FAN MOTOR)
Before introducing the food, preheat the oven to the desired temperature.
For a correct preheating operation, it is advisable to remove the tray from the oven
and introduce it together with the food, when the oven has reached the desired temperature.
Check the cooking time and turn off the oven 5 minutes before the theoretical time to
recuperate the stored heat.
Recommended for:
For foods which require the same cooking temperature both internally and externally,
i.e. roasts, spare ribs, meringue, etc.
15

CONVECTION BAKING WITH VENTILATION
(OVEN BURNER WITH FAN MOTOR)
After lighting the oven burner switch on the fan motor by turning the LIGHT & FAN
control knob (fig. 3.2) on
position.
Before introducing the food, preheat the oven to the desired temperature.
For a correct preheating operation, it is advisable to remove the tray from the oven
and introduce it together with the food, when the oven has reached the desired temperature.
Check the cooking time and turn off the oven 5 minutes before the theoretical time to
recuperate the stored heat.
It is possible to cook various different foods at the same time. Fish, cakes and meat
can be cooked together without the smells and flavours mixing.
The only precautions required are the following:
- The cooking temperatures must be as close as possible with a maximum difference
of 70-80 °F (20-25 °C) between the different foods.
- Different dishes must be placed in the oven at different times according to the cooking time required for each one. This type of cooking obviously provides a considerable
saving on time and energy.
Recommended for:
For foods of large volume and quantity which require the same internal and external
degree of cooking; for ex: rolled roasts, turkey, legs, cakes, etc.
DEFROSTING FROZEN FOODS (ONLY FAN MOTOR)
With the oven burner control knob in
position turn the LIGHT & FAN control knob
(fig. 3.2) on
position.
Only the fan and the oven lamp switch on. Defrosting takes place by the fan, without
heating.
Recommended for:
To rapidly defrost frozen foods; 2.2 lbs (1 kg) requires about one hour.
The defrosting times vary according to the quantity and type of foods to be defrosted.
16

IGNITION OF THE BROIL BURNER
IMPORTANT NOTE: the fan motor cannot be used in combination with the broil
burner. A safety device switches off the fan motor when the gas oven/broil control
knob is turned on
position.
The broil burner generates the infra-red rays for broiling.
To light the broil burner operate as follow:
1) Open the oven door to the full extent.
WARNING: Risk of explosion! The oven door must be open during this operation.
2) Press the oven control knob right down and turn clockwise (fig. 3.4) to the
position.
3) Check the broil burner has lit; if not, turn the knob counterclockwise back to
repeat the procedure from step 2.
and
4) Once the broil burner has lit, close the oven door slowly.
Fig. 3.4
If the flame extinguishes for any reason, the safety valve will automatically shut off the
gas supply to the burner.
To re-light the burner, first turn the oven control knob to position
, wait for at
least 1 minute and then repeat the lighting procedure.
VERY IMPORTANT NOTE: THE BURNER IGNITION PROCEDURE MUST ALWAYS
START WITH THE CONTROL KNOB IN THE OFF POSITION OR IT WILL NOT BE
POSSIBLE TO IGNITE THE BURNER.
Do always broil with oven door closed.
Attention: the oven door becomes very hot during operation.
Keep children away.
17

Do not use
1st STEP
Broiling level
2nd STEP
Oven cooking level
3rd STEP
Oven cooking level
4th STEP
Fig. 3.5
BROILING
Very important: the broil burner must always be used with
the oven door closed.
- Position the shelf on the second level from the top (fig. 3.5).
- Turn on the broil burner, as explained in the preceding paragraphs and let the broil burner preheat for about 5 minutes
with the door closed.
- Place the food to be cooked above the broiling pan.
- Introduce the broiling pan in the oven (fig. 3.8). The broiling
pan should be placed above the shelf and it should be centered with the broil burner (fig. 3.5).
Fig. 3.6
WRONG
Do not broil without using the broiling pan.
Important: Use always suitable protective gloves when
inserting/removing the broiling pan, shelves, pans or other
cooking utensils from the oven.
Fig. 3.7
CORRECT
Fig. 3.8
18
60’ alarm knob

MINUTE COUNTER
(fig. 4.1)
The minute counter is a timed acoustic warning device which can be set for a
maximum of 60 minutes.
The knob (Fig. 4.1) must be rotated clockwise as far as the 60 minute position and
then set to the required time by rotating it anticlockwise.
IMPORTANT WARNING: This is only a mechanical timer.
Remember to turn off the oven/broil manually.
Fig. 4.1
19
cleaning and maintenance

WARNING
Electrical Shock Hazard
Plug into a grounded 3-prong
outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
3-prong polarized
ground-type outlet
GENERAL RECOMANDATION
✓Important: Before any operation of cleaning and maintenance disconnect the
appliance from the electrical supply.
✓It is advisable to clean when the appliance is cold and especially for cleaning the
enamelled parts.
✓Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the surfaces.
✓Avoid using cleaning products with a chlorine or acidic base.
The oven must always be cleaned after every use, using suitable products and keeping in mind that its operation for 30 minutes on the highest temperature eliminates
most grime reducing it to ashes.
WARNING
When correctly installed, your product meets all safety requirements laid down
for this type of product category. However special care should be taken around
the rear or the underneath of the appliance as these areas are not designed or
intended to be touched and may contain sharp or rough edges, that may cause
injury.
ENAMELLED PARTS
✓All the enamelled parts must be cleaned with a sponge and soapy water or other
non-abrasive products.
✓Dry preferably with a microfibre or soft cloth.
✓Acidic substances like lemon juice, tomato sauce, vinegar etc. can damage the
enamel if left too long.
PAINTED PARTS AND SILK-SCREEN PRINTED SURFACES
✓Clean using an appropriate product. Always dry thoroughly.
ground
prong
IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abrasion. You are advised to use a soft cloth and neutral soap.
STAINLESS STEEL ELEMENTS
✓Stainless steel parts must be rinsed with water and dried with a soft and clean
cloth.
✓For difficult dirt, use a specific non-abrasive product available commercially or a
little hot vinegar.
✓Note: regular use could cause discolouring around the burners, because of
the high flame temperature.
WARNING
VERY IMPORTANT
Before any operation of maintenance
disconnect the appliance from the
electrical mains supply.
20
Do not use steam jet cleaners
because the humidity could
infiltrate into the appliance making
it dangerous.
INSIDE OF OVEN
The oven should always be cleaned after use when it has cooled down.
The cavity should be cleaned using a mild detergent solution and warm water.
Suitable proprietary chemical cleaners may be used after first consulting with the
manufacturers recommendations and testing a small sample of the oven cavity.
Abrasive cleaning agents or scouring pads/cloths should not be used on the cavity
surface.
NOTE: The manufacturers of this appliance will accept no responsibility for damage
caused by chemical or abrasive cleaning.
Let the oven cool down and pay special attention no to touch the hot heating elements inside the oven cavity.
BURNERS AND GRIDS
✓These parts can be removed and
cleaned with appropriate products.
✓After cleaning, the burners and their
flame distributors must be well dried
and correctly replaced.
✓It is very important to check that the
burner flame distributor and the cap
has been correctly positioned - failure
to do so can cause serious problems.
✓Check that the probe next to each
burner is always clean to ensure correct operation of the safety valves.
✓In appliances with electric ignition
keep the electrode clean so that the
sparks always strike.
✓Note: To avoid damage to the electric ignition do not use it when the
burners are not in place.

C
F
T
S
CORRECT REPLACEMENT
OF THE SEMI-RAPID
BURNERS
Fig. 5.1
Fig. 5.2
It is very important to check that the
burner flame spreader “F” and the cap
“C” have been correctly positioned (see
figs. 5.1 and 5.2 ). Failure to do so can cause serious
problems.
In appliances with electric ignition, check
that the electrode “S” (figs. 5.1 - 5.3)
is always clean to ensure trouble-free
sparking.
T
S
Check that the probe “T” (figs. 5.1 - 5.3)
next to each burner is always clean to
ensure correct operation of the safety
valves.
Both the probe and ignition plug must
be very carefully cleaned.
Fig. 5.3
A
B
CORRECT POSITION OF
TRIPLE RING BURNERS
The triple ring burner must be correctly
positioned (see fig. 5.3); the burner rib
must be fitted in their housing as shown
by the arrow.
Fig. 5.4
Fig. 5.5
The burner correctly positioned must not
rotate (fig. 5.4).
Then position the cap A and the ring B
(figs. 5.4 - 5.5).
21

CORRECT POSITION OF DUAL BURNER
The DUAL burner must be correctly positioned (see fig. 5.6); the burner rib must be
fitted as shown by the arrows.
Position the central small cap in its housing as shown by the arrows (fig. 5.7).
Position the big cap in its housing as shown by the arrows (fig. 5.8).
IMPORTANT: NEVER unscrew the burner screws (fig. 5.9).
Fig. 5.6
GAS VALVES
In the event of operating faults in the gas valves, call the Service Department.
Fig. 5.7
Fig. 5.8
Fig. 5.9
22

OVEN ACCESSORIES INSTALLATION AND REMOVAL
– Hang up the wire racks “G” on the oven walls (fig. 5.10).
– Slide in, on the guides, the shelves (fig. 5.11). Do not use the first step from the top.
The rack must be fitted so that the safety catch, which stops it sliding out, faces the
inside of the oven.
G
– Position the broiling pan above the oven shelf (see page 18).
– To dismantle, operate in reverse order.
Fig. 5.10
Safety catch
Do not use this step
Fig. 5.11
OVEN DOOR
The internal glass panel can be easily
removed for cleaning by unscrewing the
retaining screws (Fig. 5.12)
Fig. 5.12
STORAGE COMPARTMENT
The storage compartment is accessible
through the pivoting panel (fig. 5.13).
WARNING!!
Do not store flammable material
in the oven or in the storage compartment.
Fig. 5.13
23

REMOVING THE OVEN DOOR
The oven door can easily be removed as follows:
– Open the door to the full extent (fig. 5.14a).
– Open the lever “A” completely on the left and right hinges (fig. 5.14b).
– Hold the door as shown in fig. 5.14.
– Gently close the door (fig. 5.14) until left and right hinge levers “A” are hooked to part
“B” of the door (fig. 5.14b)
– Withdraw the hinge hooks from their location following arrow “C” (fig. 5.14d).
Fig. 5.14
– Rest the door on a soft surface.
– To replace the door, repeat the above steps in reverse order.
REFITTING THE OVEN DOOR
– Hold the door firmly (fig. 5.14).
– Insert the hinge tongues into the slots, making sure that the groove drops into place
as shown in the fig. 5.15a.
– Open the door to its full extent.
– Fully close the levers “A” on the left and right hinges, as shown in the figure 5.15b.
Fig. 5.14a
– Close the door and check that it is properly in place.
REPLACING THE OVEN LIGHT
A
B
Fig. 5.14b
Fig. 5.14c
Before any maintenance is started involving electrical parts of the appliance, it must be
disconnected from the power supply.
✓Let the oven cavity and the broil burner cool down;
✓Switch off the electrical supply;
✓Remove the protective cover;
✓Unscrew and replace the bulb with a new one suitable for high temperatures (300°C570°F) having the following specifications: 120V 60 Hz, 15W, E14;
✓Refit the protective cover.
NOTE: Oven bulb replacement is not covered by your guarantee.
Fig. 5.15a
A
C
24
Fig. 5.14d
Fig. 5.15b

DO’S AND DO NOT’S
• Do always use the oven with the door closed.
• Do always broil with the door closed.
• Do read the user instructions carefully before using the range for first time.
• Do allow the oven to heat for about two hours, before using for the first time, in order
to expel any smell from the new oven insulation, without the introduction of food.
• Do clean your oven regularly.
• Do remove spills as soon as they occur.
• Do always use oven gloves when removing food shelves and trays from the oven.
• Do not allow children near the range when in use.
• Do not allow fat or oils to build up in the oven base, or oven accessories.
• Do not place cooking utensils or plates directly onto the oven base.
• Do not place hot enamel parts in water. Leave them to cool first.
• Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in
contact with enamel parts (i.e. inside the oven).
• Do not use abrasive cleaners or powders that will scratch the surface of the stainless
steel and the enamel.
• Do not attempt to repair the internal workings of your range.
• Do remove the protective film before the first use.
• Fire risk! Do not store flammable material in the oven and in the storage
compartment.
• Do not use the oven with the oven door open.
• Do not use the oven to warm or heat a room.
FOR YOUR SAFETY
Under no circumstances should any external covers be removed for servicing or
maintenance except by suitably qualified personnel
25
26
27
The manufacturer cannot be held re­spon­sible for possible inaccuracies due to printing or transcription errors in
the present booklet.
The manufacturer re­serves the right to make all modifications to its products deemed necessary for manufacture
or commercial reasons at any moment and without prior notice, without jeopardising the es­sential functional and
safety characteristics of the appliances.
Cod. 1104633 - ß2