20X/30X PoE IR FAST DOME IP Camera
PSR5024EX20, PSR5024EX30
MERIT LILIN ENT. CO., LTD
http://www.meritlilin.com
66-PSR502CSE
Instr uction Manual
IMPORTANT SAFEGUARDS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE FRONT OR BACK COVER.
NO USER SERVICEABLE PARTS INSIDE.
FOR MAINTENANCE, CONTACT QUALIFIED
SERVICE PERSONNEL.
SYMBOL DEFINITION
The lightning within a triangle is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within a triangle is intended
to alert the user to the presence of important operating and
maintenance instructions in this guide.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
WITH AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
WARNINGS & CAUTIONS
Please read the manual before attempting installation or operation
1. Do not use any chemical detergent to clean the machine surface; use a damp cotton cloth
only. Regularly clean the dome cover to ensure focusing accuracy.
2. Install the Fast Dome in a dry area. Water and high humidity may damage
internal parts. External housing should be used for outdoor installation.
3. Use parts supplied by the manufacturer only; use of unqualified part will void the warranty.
4. Avoid installing the equipment on an unstable surface. Make sure the installation location is
solid and stable. Falling equipment may injure personnel and damage the equipment.
5. Do not install the equipment near any flammable gas. Violation may cause fire or injury.
6. Avoid running video and signal cables through or passing interference sources such
as electromagnetic wave, broadcast station, power generator, elevator motor, or high
voltage are, etc. Interference may cause the equipment not to function properly.
7. Make sure the power cable is properly connected. Loosened power cables may cause
serious short circuit or fire.
8. Make sure all cables are properly connected. Do not place any object on the cables.
Replace the cable if damaged. Violation may cause short circuit, fire, and injury.
9. Make sure all wires and cables are properly grounded to avoid damage caused by lightning.
10. Do not put any foreign objects inside the equipment and do not spray any liquid on the
equipment to avoid short circuit and subsequent damage.
11. Do not touch power connection with wet hands to avoid short circuit or electric shock.
12. Do not apply external force on the equipment. Violation may cause damage.
13. Do not expose the equipment directly to sunlight. Violation may cause color fading or damage.
14. Do not install the equipment in high or low temperature environment to
avoid damage. The operating temperature is between -40°C - +50°C.
15. The Fast Dome consists of highly sensitive electronic parts inside. Do not try to repair the
equipment. Only a qualified technician may disassemble and repair the equipment. Shut off
the power before disassembling the equipment and do not power it on unless the casing is
completely closed.
16. Turn off the power immediately and contact the technician when the following occurs:
A. Damage on power cable or plug.
B. Water leak into the equipment.
C. Fast Dome does not function normally.
D. Equipment falling on the ground or damage on external casing.
Introduction
LILIN PSR5024EX20 / PSR5024EX30 is a day&night 2M resolution color high speed dome
camera, which supports HD/Full HD resolution and digital signal processing (DSP) technology.
The camera features 20/30X optical lens, digital zoom, auto focus/iris control, IR cut, auto gain
control, wide dynamic range (WDR), back-light compensation, digital noise reduction, and
electronic stabilization.
PSR5024EX20/30 is only 198mm in diameter. Within the adjustable range, this camera can
either move smoothly or in high speed. The camera’s moving speed ranges from 0.1°/s to 300°/s.
The continuous 360 pan capability is free from the restriction of direction. Every PSR5024 camera
supports 256 preset positions, which can be automatically monitored if set to the auto-scan mode.
PSR5024EX20/30 supports 4 sets of alarm-input. In a matter of seconds, your dome camera can
be targeted to any preset position. The alarm inputs correspond to the preset positions for even
more secure perimeter monitoring.
The new PSR5024EX20/30 camera has a compact and streamlined design. With the
comprehensive functions that deliver maximum ease of use, the PSR5024 series is your ideal
surveillance camera.
The cutting - edge H.264 AVC encoding technology delivers better compression rate and superior
video quality at 56 Kbps to 3 Mbps bit rate. The d ual streaming design supports both M JPEG and
H.264 AVC formats to allow v ideo streaming at low bandwidth (Internet) and high bandwidth (LAN)
for q uality optimization .
Package Contents
1. Dome camera
2. 350mm safety strap
+M3x8L machine bolts with
washers (x2)
3. 5mm hex key
+ M6x10L hex machine bolts (x3)
( For camera quick
( For safety strap )
4. Installation guide
20X/30X PoE IR FAST DOME IP Camera
PSR5024EX20, PSR5024EX30
Instr uction Manual
5. Software CD
release adaptor)
Connector Hub
RESET
VIDEO
GND
Micro SD Card
CVBS
L
N
PoE
RS485
AC24V
(DC24V)
- +
GND
NC2
NO2
COM2
NC1
COM1
NO1
IN4
GND
IN3
IN2
IN1
OUT
GND
IN
Reset button
RJ-45 network connector (PoE supported)
LAN: 10/100Mbps
Recommended cable: CAT5
Micro SD card slot: supports Micro SD and SDHC card
Audio In
Audio signal: 1.4Vp-p(1 Vrms)
Recommended cable: shielded signal cable
Alarm In/Out
Every camera provides 4 external alarm inputs and 2 alarm outputs
Voltage for alarm inputs: 5.6Vmax; alarm output: 1A 24VDC
Recommended cable: UL 26AWG 80°C 300V
UL 24AWG 80°C 300V
RS-485 connector
Power cable (AC24V)
Recommended cable: 0
Copper Wire (AWG)
Cable Length
( approx. )
#24
(0.22mm 2)
#22
(0.33mm 2)
#20
(0.52mm 2)
#18
(0.83mm 2)
(m)
20
30
45
75
(ft)
65
100
160
260
Video Out
V ideo signal output: CVBS 1.0Vp-p 75Ω BNC
R ecommended cable: CABLE 5C2V
Installation
Structural Diagram
396mm
Camera body
Camera quick release adaptor
C amera bracket
Camera bracket base
198mm
ø196
Step 1 Remove the bracket from the base
Loosen the four bolts from the base (FIG.1) and push the hinge upwards to separate it from the base (FIG.2).
[FIG.1]
[FIG.2]
Step 2 Secure the bracket base to the wall
Attach the installation sticker to the wall and drill four holes according to the instructions (FIG.3). Tighten
four bolts to secure the base to the wall (FIG. 4). To use the central hole on the base, first hammer the lid off
(FIG.5).
Note The bolts are not included in the package.
CAUTION
PLEASE USE
CAUTION
5/16" OR M8
EXPANSION BOLT.
PLEASE USE
5/16" OR M8
EXPANSION BOLT.
60mm
請搭配使用
5/16" 或 M8
膨脹螺栓。
60mm
請搭配使用
5/16" 或 M8
膨脹螺栓。
[FIG.3]
[FIG.4]
[FIG.5]
Step 3 Attach the quick release adaptor to the bracket
First remove the quick release adaptor from the camera body. Align the adaptor with the bracket before
tightening the bracket bolts (FIG. 6 & FIG.7). Then slide the adaptor and bracket together down the hinge to
connect to the base (FIG.8). Note: The three bolts on the adaptor must be loosened first to remove the adaptor.
[FIG.6]
[FIG.7]
[FIG.8]
Step 4 Slip the control wires through the bracket
Properly secure the safety strap to the bracket, and slip the safety strap, RJ-45 cable, and AC24V power
connector through the bracket (FIG.9 & FIG.10). Secure the bracket to the base (FIG.11)
Note: The AC24V power connector is not needed to be connected when a PoE device is used.
[FIG.9]
[FIG.10]
[FIG.11]
Step 5 Connect the control wires
To prevent the camera from falling, you should first secure the safety strap to the camera body (FIG.12).
Next, connect the RJ-45 cable and AC24V power connector to the hub on the body (FIG.13 & FIG.14).
GND
NC2
COM2
NO2
NC1
COM1
NO1
GND
IN4
IN3
IN2
IN1
[FIG.13]
OUT
GND
IN
[FIG.12]
[FIG.14]
Step 6 Install the camera body
Allign markings on the quick release adaptor and the camera body. Twist the camera body clockwise
into the adaptor (FIG.15). Tighten the three bolts on the adaptor (FIG.16) to secure the camera and finish
the installation (FIG.17).
[FIG.15]
[FIG.18]
[FIG.16]
[FIG.17]
Note: After completing the installation of the dome camera, lock the
safety screw on the camera bracket to avoid falling (FIG.18).
Low Temperature Power-Up
Camera may perform abnormally at low temperature. Hence, follow the below procedure
when the camera is off due to power outage or other issues and needs to be restarted under
-40°C to -5°C.
Low temperature power-up procedure
Power up and wait for the heater to warm up for 15 minutes before you operate the camera.
Specifications
General
PSR5024EX20
Model
Power Supply &
Power Consumption
Image Pick-up Device
PSR5024EX30
A C 2 4 V ± 1 0 % , 8 0 W / D C 2 4 V, 8 0 W / P o E + + , 8 0 W
1 / 2 . 8 " Ty p e C M O S S e n s o r ( S o n y I M X 1 4 0 )
Effective Pixels
1944(H) x 1224(V) = 2,379,456 (pixels)
To t a l N u m b e r o f P i x e l s
1952(H) x 1236(V) = 2,412,672 (pixels)
Progressive Scan
Scanning System
Video Output
C V B S 1 . 0 V p - p / 7 5ΩB N C
Color
Minimum
Illumination
0.5 lux (1/30 sec, F1.6(Wide), 50IRE, AGC-Gain: 30dB ICR-OFF)
Color DSS
0.1 lux (1/8 sec, F1.6(Wide), 50IRE, AGC-Gain: 30dB ICR-OFF)
Mono
0.2 lux (1/30 sec, F1.6(Wide), 50IRE, AGC-Gain: 30dB ICR-ON)
Mono DSS
0.01 lux (1/8 sec, F1.6(Wide), 50IRE, AGC-Gain: 30dB ICR-ON)
0 lux
IR On
Casing
W e a t h e r - p r o o f I P 6 6 , Va n d a l - p r o o f I K 1 0
Safety Certifications
O p e r a t i n g Te m p e r a t u r e
CE, FCC, UL
-40°C ~ +50°C (-40°F ~ 122°F)
Operating Humidity
Dimensions
0% ~ 90%
395mm(H) x 198mm(D)
6000 g
Weight
Pan & Tilt
360° Endless
Pan Range
Pan Mode
Pan Speed
Manual, Auto, Manual Position, Sequential Position
Manual Approx. 0.1°/s ~ 120°/s 8 Steps, Preset Approx. 1°/s ~ 300°/s, Alarm Trigger Speed 300°/s
-30 ° ~ +210 °
Tilt Range
Tilt Mode
Tilt Speed
Lens
Zoom Ratio
Focal Length
F-number
Minimum Object Distance
Iris range
Field of View
Manual, Auto, Manual Position, Sequential Position
Manual Approx. 0.1°/s ~ 120°/s 8 Steps, Preset Approx. 1°/s ~ 300°/s, Alarm Trigger Speed 300°/s
20X Optical Zoom
30X Optical Zoom
4.7 mm (WIDE) to 94.0 mm(TELE)
4.3 mm (WIDE) to 129.0 mm(TELE)
1 : 1.6 (Wide) ~ 3.5 (Tele)
1 : 1.6 (Wide) ~ 4.7 (Tele)
30 cm (WIDE end), 1.5M (TELE end)
10 cm (WIDE end), 1.5M (TELE end)
F1.6 ~ 32, Close
F1.6 ~ 32, Close
Approx. 59.94°( H ) 36.16°( V ) (WIDE end),
Approx. 64.45°( H ) 39.27°( V ) (WIDE end),
approx. 3.30°( H ) 1.87°( V ) (TELE end), (1080p mode) approx. 2.41°( H ) 1.36°( V ) (TELE end), (1080p mode)
Main Function
Control Function
Digital Zoom Ratio
Pan and Tilt/ Zoom and Focus/ Iris and ICR/ 256 Preset Position/ Home Position
x16
Zoom Speed
0 ~ 7 Selectable[ Fast : Approx. 6.0 Second ( Tele to Wide ) in Manual Mode ]
Focus Speed
0 ~ 7 Selectable [ Fast : Approx. 6.0 Second ( Far to Near ) in Manual Mode ]
Auto ( Continue / Interval / Zoom Trigger / One Push), Manual Focus
Focus
ALC ( Adjustable Output Target Level ) / Manual
Iris
Day & Night
Day/Night/Auto
Electric Shutter Speed
Auto / manual(1/30(25) to 1/10,000)
Exposure Mode
AUTO / IRIS.P / SHUT.P / MANUAL
Back Light
Sharpness
White Balance
Auto Gain Control
Digital Noise Reduction
Digital Image Stabilization
Defog
Auto Mode
Dynamic Privacy Zone Mask
Digital Effect
OFF / BLC / WDR
Adjustable
ATW / Indoor(3200K) / Outdoor(5800K) / Manual(1800K ~10500K)
0~30dB
Off/On (2D, 3D)
Off/On
Off / On(Auto / Manual)
OFF / AUTO / SEQ / TOUR
Off/On (Up to 16 Areas)
Off/Mirror
Alarm Input/Output
4 Inputs (TTL 5Vdc), 2 Outputs (0.5A 120Vac, 1A 24Vac)
Scheduling Setting
Off/Auto Mode/Preset Position
Peak Wavelength
infrared
LED
Beam Sprea
Radiant Distance
850nm
Automatically adjusted, Depending on the zoom ratio
150M
Design and specifications are subject to change without notice.
Network Function
Video Compression
H.264 Main and High Profile, Motion JPEG
Resolution
1080P(1920x1080), 720P(1280x720), D1(720x480), CIF(352x240)
Frame Rate
Dual-stream mode, H.264 : up to 60 FPS @ 1920 x 1080, Motion JPEG : up to 30 FPS @ 720 x 480
2WDR mode, H.264 : up to 30 FPS @ 1920 x 1080 , Motion JPEG : up to 30 FPS @ 720 x 480
Video Streaming
RTP/HTTP, RTP/TCP, RTP/UDP, Multicast
Video Bitrate
128Kbps to 12Mbps, Frame rate and bit rate controllable on-the-fly,
VBR / CBR / GOP supported
Encryption
Base64 HTTP encryption
Access
Multiple user access levels with password protection
User accounts
10 user accounts available
RTSP Authentication
On/ Off
IP address filter
Yes
Multi IP address
Yes
Users
10 simultaneous users
OSD
Text overlay for date, time, camera name, and PTZ position
IVS (Intelligent Video
Surveillance)
Alarm event triggers
Motion detection, Zone Entering, Direction detection, Zone
Alarm / motion / audio / Network loss detection
Alarm event actions
FTP, HTTP post, SD card
Alarm weighted mode
Yes
CPU & Memory
Embedded SoC, 1.2GHz, Dual ARM Cortex-A9 & 600MHz ARM11, 1GB DDR3
Memory, 256MB Flash Memory
Web PTZ Control
Pan, tilt, zoom in/ out, absolute position, and video-click-n-move
PTZ Preset Scheduling Yes, via web interface
Maintenance
Network Interface
Firmware update via HTTP, Firmware available at web site
10/ 100/ 1000 Mbps Base-T, RJ-45
OS requirement
Windows 2000, Windows XP, Windows Vista, Windows 7, Windows 8
Web browser
CPU requirement
Windows Internet Explorer 9.0 or above
Intel Core 2 Duo e6400 2.13GHz or above
RAM requirement
2GB or above, Independent Display Card
Mobile Devices
Video Management
Ipv4, IPv6, TCP, UDP, HTTP, SMTP, NTP, DDNS, UPnP, FTP, ARP, DHCP, PPPoE,
DNS, RTSP, RTCP, Telnet, ICMP, IGMP, Onvif Profile S, SNMP, SIP, Bonjour
iPhone, iPad and Android support
ONVIF & LILIN HTTP API / Navigator enterprise 1.0 support
Video Display
LILIN Universal ActiveX & LILIN Java Applet
OS
Embedded Linux 3.8.0
Audio
Two-way, G.711/ PCM
SD Card Recording
Support Micro SD/SDHC/SDXC card for circular recording (card is not included)
Network Protocols
Design and specifications are subject to change without notice.
66-PSR502CSE-1
20X/30X PoE IR FAST DOME IP Camera
PSR5024EX20, PSR5024EX30
MERIT LILIN ENT. CO., LTD
http://www.meritlilin.com
66-PSR502CSE
Instr uction Manual