FRENCH DOOR
BOTTOM MOUNT
R E F R I G E RA T O R
USE & CARE GUIDE
W W W. W H I R L P O O L . C O M
U .S.: 1-800-253-1301
W10859982A
W W W. W H I R L P O O L . C A
C A N A D A : 1 -8 0 0 -8 0 7 -6 7 7 7
TABLE OF CONTENTS
Congratulations on your purchase and welcome to
the Whirlpool Brand family of high-quality
appliances. Your new Whirlpool® French Door
Refrigerator combines advanced cooling technology
with simple operation and high efficiency.
Each appliance that leaves our factory is inspected
thoroughly to ensure that it is working properly.
REFRIGERATOR SAFETY ....................................................... 3
Proper Disposal of Your Old Refrigerator.............................. 3
PARTS AND FEATURES.......................................................... 4
What’s New Behind the Doors?............................................. 4
INSTALLATION INSTRUCTIONS............................................ 5
Unpack the Refrigerator......................................................... 5
- Remove the Packaging.........................................................5
- Clean Before Using...............................................................5
Location Requirements.......................................................... 5
Remove and Replace Refrigerator Doors.............................. 6
-
Remove Right-Hand Refrigerator Door ................................7
Remove Left-Hand Refrigerator Door ..................................7
Replace Right-Hand Refrigerator Door ................................8
Replace Left-Hand Refrigerator Door...................................8
Final Steps ............................................................................8
Remove and Replace Freezer Drawer Front ......................... 9
- Remove Drawer Front...........................................................9
- Replace Drawer Front...........................................................9
- Final Steps ............................................................................9
Electrical Requirements ....................................................... 10
Water Supply Requirements ................................................ 10
Connect the Water Supply................................................... 11
- Connect to Water Line........................................................11
- Connect to Refrigerator ......................................................11
- Complete the Installation ....................................................12
Please read the Use and Care Instructions in this
guide before operating your new refrigerator. Like
all appliances, your refrigerator may require
maintenance or repair from time to time, but you
can help to ensure that your refrigerator provides
many years of reliable service by following the
instructions in this guide.
- Additional Features .............................................................21
Water and Ice Dispensers ....................................................21
-
Flush the Water System......................................................22
Calibrate Measured Fill .......................................................22
Dispensing...........................................................................23
The Water Dispenser...........................................................23
The Ice Dispenser ...............................................................24
The Dispenser Light ............................................................24
The Dispenser Lock ............................................................24
Ice Maker and Ice Storage Bin.............................................25
- Ice Production Rate ............................................................25
- Style 1 - Ice Maker in the Refrigerator ................................25
- Style 2 - Ice Maker in the Freezer .......................................25
REFRIGERATOR FEATURES ................................................26
Refrigerator Shelves .............................................................26
- Shelves and Shelf Frames ..................................................26
- Tuck Away Shelf..................................................................26
Crisper Drawers/Pantry Drawer/Crisper Cover ...................26
Crisper Humidity Control......................................................27
Temperature-Controlled Drawer ..........................................27
-
Style 1 - Electronic Control.................................................27
Style 2 - Manual Control .....................................................27
Drawer Removal and Replacement ....................................28
Drawer Divider.....................................................................28
Meat Storage Guide............................................................28
Refrigerator Leveling, Door Closing and Alignment ............ 14
FILTERS AND ACCESSORIES.............................................. 15
Water Filtration System........................................................ 15
DOOR FEATURES ..................................................................28
Door Bins ..............................................................................28
FREEZER FEATURES ............................................................28
Pizza Pocket and Drawer Divider.........................................28
REFRIGERATOR CARE .........................................................29
Cleaning................................................................................29
- Install the Water Filter .........................................................15
- The Water Filter Status Light ..............................................15
- Replace the Water Filter .....................................................16
- Exterior Cleaning.................................................................29
- Interior Cleaning..................................................................29
- Condenser Cleaning ...........................................................30
Install Air Filter ...................................................................... 16
Lights ....................................................................................30
Vacation and Moving Care...................................................30
Handle Installation and Removal ......................................... 12
- Install Handles.....................................................................12
- Remove the Handles ..........................................................13
- Installing the Air Filter..........................................................16
- Installing the Filter Status Indicator ....................................16
- Replacing the Air Filter........................................................17
Install Produce Preserver ..................................................... 17
- Installing the Produce Preserver ........................................17
- Installing the Status Indicator .............................................18
- Replacing the Produce Preserver.......................................18
Accessories .......................................................................... 18
REFRIGERATOR USE............................................................ 19
Opening and Closing Doors................................................. 19
Using the Controls ............................................................... 19
- Viewing and Adjusting Temperature Set Points.................19
- Cooling On/Off....................................................................20
- Options................................................................................20
2
- Vacations.............................................................................30
- Moving.................................................................................30
TROUBLESHOOTING ............................................................31
Operation ..............................................................................31
Noise.....................................................................................32
Temperature and Moisture...................................................33
Ice and Water .......................................................................34
Doors ....................................................................................36
WATER FILTER CERTIFICATIONS.......................................37
PERFORMANCE DATA SHEET.............................................38
WARRANTY ............................................................................39
SERVICE NUMBERS ..........................................BACK COVER
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
DANGER
WARNING
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
■ Do not use an adapter.
■ Do not use an extension cord.
■ Disconnect power before servicing.
■
■
■
■
■
■
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
■ Connect to a potable water supply only.
■ Use nonflammable cleaner.
■ Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
■ Use two or more people to move and install refrigerator.
■
■
■
Disconnect power before installing ice maker (on ice maker
kit ready models only).
Use a sturdy glass when dispensing ice (on some models).
Do not hit the refrigerator glass doors (on some models).
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
play with the appliance.
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
Proper Disposal of
Your Old Refrigerator
WARNING
Before You Throw Away Your
Old Refrigerator or Freezer:
Take off the doors.
Leave the shelves in place so that
children may not easily climb inside.
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Important information to know about disposal of
refrigerants:
Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
3
PARTS AND FEATURES
A
B
C
I
D
H
E
F
A. Ice maker
B. Air filter
C. Water filter
D. Door bins
E. Crispers
F. Pantry drawer
G. Freezer drawer
H. LED ramp-on lighting
I. In-Door-Ice® ice
dispensing system
G
What’s New Behind the Doors?
Your Whirlpool® French Door Refrigerator comes equipped with various
innovative storage and energy efficient features.
Energy and Normal Operating Sounds
Water Filter
Your new French Door Bottom Mount refrigerator has been
designed to optimize energy efficiency, and better regulate
temperatures to match cooling demand. You may notice that it
operates differently from your previously owned refrigerator. It is
normal for the high-efficiency compressor to run for extended
periods of time at varying speeds in order to consume only the
energy necessary for optimum efficiency. In addition, during
various stages of the cooling cycle, you may hear normal
operating sounds that are unfamiliar to you.
NSF® Certified filter reduces chlorine taste and odor, particulates
(class I), lead, and mercury. Replacing the water filter every
6 months ensures clean, filtered drinking water.
More Storage Space
Ethylene is a natural gas produced by fruits and vegetables to
promote ripening. The Produce Preserver absorbs ethylene, to
delay the over-ripening of fresh produce. As a result, certain
produce items will stay fresh longer.
The French Door Bottom Mount has the most fresh food storage
space available, including a full-width, temperature controlled,
pantry drawer perfect for storing veggie trays or party platters.
Air Filter
An air filter is 15 times more powerful than baking soda at
reducing common food odors inside the refrigerator.
Produce Preserver (on some models)
In-Door-Ice® Ice Dispensing System
Water Dispenser with Measured Fill
(on some models)
The ice storage bin located in the door provides an entire extra
shelf of storage space, and the storage bin is removable for easy
access to filtered ice.
The measured fill feature allows you to dispense the desired
amount of filtered water.
Dual Evaporator (on some models)
The refrigerator and freezer compartments have dedicated
evaporators to provide fresh and frozen foods with separate
climates. Frozen food stays cold and dry, while fresh food
remains at the ideal temperature and humidity.
LED Lighting
The LED lights do not ever need to be replaced.
Door Alarm
A helpful alarm sounds when the refrigerator door or freezer
drawer is left ajar.
Power Outage Indicator
If the power should go out while you are away from home, this
indicator will let you know the refrigerator has been without
power.
4
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
■
Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
■
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see “Refrigerator Safety.”
■
Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
“walk” the refrigerator when trying to move it, as floor
damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in “Refrigerator Care.”
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Location Requirements
WARNING
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature range
for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This refrigerator is designed for indoor, household
use only.
To ensure proper ventilation for your refrigerator, allow for a ¹⁄₂"
(1.25 cm) of space on each side and at the top. Allow for a 1"
(2.54 cm) space behind the refrigerator. If your refrigerator has an
ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 3³⁄₄" (9.5 cm) minimum space between the refrigerator
and wall to allow the door to swing open.
¹⁄₂" (1.25 cm)
3³⁄₄" (9.5 cm)
5
INSTALLATION INSTRUCTIONS
Remove and Replace Refrigerator Doors
NOTE: Measure the width of your door opening, to see whether or not you need to remove the refrigerator doors to move the
refrigerator into your home. If door removal is necessary, see the following instructions.
IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator
control OFF. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.
Gather the required tools and read all instructions before removing doors.
TOOLS NEEDED: ³⁄₁₆" hex key wrench and a #2 Phillips screwdriver
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
Door Removal and Replacement
Style 1 – Water Dispenser
Tubing Connection
Style 2 – Water Dispenser
Tubing Connection
Top Right Hinge
B
C
A
D
A. ³⁄₁₆" Internal Hex-Head Screws
B. Hinge Cover Screw
C. Top Hinge Cover
D. Top Hinge
A
A
A. Outer Ring
Wiring Plug
Top Left Hinge
A
C
B
A. ³⁄₁₆" Internal Hex-Head Screws
B. Ground Wire (Do Not Remove)
C. Do Not Remove Screws
6
A. Outer Ring
INSTALLATION INSTRUCTIONS
Remove Right-Hand Refrigerator Door
Remove Left-Hand Refrigerator Door
IMPORTANT: The tubing and wiring for the water dispenser run
through the left-hand door hinge, so they must be disconnected
before removing the door.
1. Using a Phillips screwdriver, remove the cover from the top
hinge.
WARNING
A
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the
door gasket magnets to hold the door in place while you are
working.
3. Using a Phillips screwdriver, remove the cover from the Top
Hinge.
4. Using the ³⁄₁₆" hex key wrench, remove the two internal hex
head screws from the top hinge, and set aside.
NOTE: Do not remove the two locator screws. These screws
will help you align the hinge when you replace the door.
B
A. Top hinge cover screw
B. Top hinge cover
2. Disconnect the water dispenser tubing located on top of the
door hinge.
Style 1 - Press the outer ring against the face of the fitting
and gently pull the dispenser tubing free.
NOTE: The water dispenser tubing remains attached to the
left-hand refrigerator door.
A
B
A B
C
D
A. Top hinge cover screw
B. Top hinge cover
C. ³⁄₁₆" Internal hex head screws
D. Top hinge
A. Outer ring
B. Face of fitting
WARNING
Excessive Weight Hazard
Use two or more people to lift the refrigerator door.
Failure to do so can result in back or other injury.
5. Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.
7
INSTALLATION INSTRUCTIONS
Style 2 - Firmly pull up on the clasp. Then, pull the tubing out
of the fitting.
NOTE: The water dispenser tubing remains attached to the
left-hand refrigerator door.
5. Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.
NOTE: It may not be necessary to remove the bottom hinges
and brake feet assemblies to move the refrigerator through a
doorway.
■
Only if necessary, use a driver with a #2 square bit tip to
remove the bottom hinges and a ³⁄₈" nut driver to remove
the brake feet screws.
Replace Right-Hand Refrigerator Door
1. Set the right-hand door onto the bottom hinge pin.
2. Insert the top hinge pin into the open hole in the top of the
refrigerator door.
3. Using the two ³⁄₁₆" internal hex head screws, fasten the hinge
to the cabinet. Do not tighten the screws completely.
3. Disconnect the wiring plug located on top of the door hinge.
■ Grasp each side of the wiring plug. With your left thumb,
press down to release the catch and pull the sections of
the plug apart.
NOTE: Do not remove the green, ground wire. It should
remain attached to the door hinge.
Replace Left-Hand Refrigerator Door
IMPORTANT: Do not intertwine the water tubing and wiring
bundles when reconnecting them.
1. Set the left-hand door onto the bottom hinge pin.
2. Using the two ³⁄₁₆" internal hex head screws, fasten the hinge
to the cabinet. Do not tighten the screws completely.
3. Reconnect the water dispenser tubing.
Style 1 - Insert the tubing into the fitting until it stops and the
outer ring is touching the face of fitting.
Style 2 - Insert the tubing firmly into the fitting until it stops.
Close the clasp around the tubing. The clasp snaps into place
between the fitting and the collar.
4. Using the ³⁄₁₆" hex key wrench, remove the two internal hex
head screws from the top hinge, and set aside.
NOTES:
■
Provide additional support for the refrigerator door while
the hinges are being removed. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
■
Do not remove the two locator screws. These screws will
help you align the hinge when you replace the door.
A
B
C
A. ³⁄₁₆" Internal hex head screws
B. Ground wire (do not remove)
8
C. Locator screws (do not
remove)
4. Reconnect the electrical wiring.
■ Push together the two sections of the wiring plug.
Final Steps
1. Completely tighten the four internal hex head screws (two on
the right-hand door hinge and two on the left-hand door
hinge).
2. Replace both top hinge covers.
INSTALLATION INSTRUCTIONS
Remove and Replace Freezer Drawer Front
Depending on the width of your door opening, it may be
necessary to remove the freezer drawer front to move the
refrigerator into your home.
IMPORTANT:
■ If the refrigerator was previously installed and you are moving
it out of the home, before you begin, turn the refrigerator
control OFF, and unplug the refrigerator or disconnect power.
Remove food from the freezer drawer.
■
Two people may be required to remove and replace the
freezer drawer front.
Replace Drawer Front
1. Pull out the freezer drawer glides to their full extension.
2. Holding the drawer front by its sides, align the two plastic
studs, located at the bottom, inside the drawer front, with the
drawer glide bracket slots.
NOTE: It helps if one person holds the drawer glides steady
while another person aligns the drawer front and inserts the
studs into the slots.
Tool Needed: ¹⁄₄" hex driver
Remove Drawer Front
1. Open the freezer drawer to its full extension.
2. Remove the two screws at the top, inside the drawer front
(one on the left-hand side and one on the right-hand side)
that fasten the drawer front to the drawer glides.
3. Lift up on the drawer front to release the plastic studs from
the drawer glide bracket slots.
A
B
A
A. Drawer front screw
B. Drawer front plastic stud
3. Replace and tighten the two screws at the top of the drawer
front (one on the left-hand side and one on the right-hand
side).
Final Steps
A. Drawer glide bracket slots
WARNING
4. Slide the drawer glides back into the freezer.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Reset the controls. See “Using the Control(s).”
3. Return all removable door parts to doors and the food to
refrigerator.
9
INSTALLATION INSTRUCTIONS
Electrical Requirements
Recommended Grounding Method
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn Cooling OFF, and then disconnect the
refrigerator from the electrical source. When you have finished,
reconnect the refrigerator to the electrical source and turn
Cooling ON. See “Using the Control(s).”
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Water Supply Requirements
A cold water supply with water pressure between 35 and 120 psi
(241 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
NOTE: If the water pressure is less than what is required, the flow
of water from the water dispenser could decrease or ice cubes
could be hollow or irregular shaped.
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
■ Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 35 and 120 psi (241 and
827 kPa).
Allow the storage tank on the reverse osmosis system to refill
after heavy use. The tank capacity could be too small to keep
up with the requirements of the refrigerator.
NOTE: Faucet mounted reverse osmosis systems are not
recommended.
■
If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See “Water
Filtration System.”
If you have questions about your water pressure, call a licensed,
qualified plumber.
10
INSTALLATION INSTRUCTIONS
Connect the Water Supply
Read all directions before you begin.
IMPORTANT:
■ Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and
ordinances.
■
The gray water tubing on the back of the refrigerator (which is
used to connect to the household water line) is a PEX
(cross-linked polyethylene) tube. Copper and PEX tubing
connections from the household water line to the refrigerator
are acceptable, and will help avoid off-taste or odor in your
ice or water. Check for leaks.
If PEX tubing is used instead of copper, we recommend the
following Whirlpool Part Numbers:
W10505928RP (7 ft [2.14 m] jacketed PEX),
8212547RP (5 ft [1.52 m] PEX), or
W10267701RP (25 ft [7.62 m] PEX).
■
Install tubing only in areas where temperatures will remain
above freezing.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
■ Flat-blade screwdriver
■
⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches
■
¹⁄₄" nut driver
NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve
which reduces water flow and clogs easier.
■
Ensure that you have the proper length needed for the
job. Be sure both ends of the copper tubing are cut
square.
■
Slip compression sleeve and compression nut onto
copper tubing as shown. Insert end of tubing into outlet
end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not
overtighten.
A
B
A. Compression sleeve
B. Compression nut
C
C. Copper tubing
5. Place the free end of the tubing into a container or sink, and
turn on main water supply to flush out tubing until water is
clear. Turn off shutoff valve on the water pipe.
NOTE: Always drain the water line before making the final
connection to the inlet of the water valve, to avoid possible
water valve malfunction.
6. Bend the copper tubing to meet the water line inlet, which is
located on the back of the refrigerator cabinet as shown.
Leave a coil of copper tubing to allow the refrigerator to be
pulled out of the cabinet or away from the wall for service.
Connect to Refrigerator
Follow the connection instructions specific to your model.
Connect to Water Line
Style 1
IMPORTANT: If you turn the refrigerator on before the water is
connected, turn the ice maker OFF.
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Use a quarter-turn shutoff valve or the equivalent, served by a
¹⁄₂" household supply line.
NOTE: To allow sufficient water flow to the refrigerator, a
minimum ¹⁄₂" size household supply line is recommended.
1. Remove plastic cap from water valve inlet port. Attach the
copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not
overtighten. Confirm copper tubing is secure by pulling on
copper tubing.
2. Create a service loop with the copper tubing. Avoid kinks
when coiling the copper tubing. Secure copper tubing to
refrigerator cabinet with a “P” clamp.
A
B
A
B
C
D
C
D
A. Sleeve
B. Nut
C. Copper tubing (to refrigerator)
D. Household supply line (½" minimum)
4. Now you are ready to connect the copper tubing to the
shutoff valve. Use ¹⁄₄" (6.35 mm) OD soft copper tubing to
connect the shutoff valve and the refrigerator.
A. Copper tubing
B. “P” clamp
C. Compression nut
D. Compression sleeve
11
INSTALLATION INSTRUCTIONS
3. Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Complete the Installation
Style 2
WARNING
1. Unplug refrigerator or disconnect power.
2. Remove and discard the short, black plastic part from the
end of the water line inlet.
3. Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not
overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not
touch the cabinet’s side wall or other parts inside the cabinet.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
A
B
C
A. Household water line
B. Nut (purchased)
D
C. Ferrule (purchased)
D. Refrigerator water tubing
4. Install the water supply tube clamp around the water supply
line to reduce strain on the coupling.
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
7. On some models, the ice maker is equipped with a built-in
water strainer. If your water conditions require a second water
strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube
connection. Obtain a water strainer from your appliance
dealer.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See “Water and Ice Dispensers.”
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to
completely fill the ice storage bin.
Handle Installation and Removal
Parts Included: Door handles (2), Drawer handle(s) (1 or 2
depending on model), ¹⁄₈" hex key, spare setscrew(s)
NOTE: With the handles laying on a flat surface, the handles
intended for the drawers are more curved. They will not mount
flush against the doors.
2. Open a refrigerator compartment door. On the closed door,
place a handle onto the shoulder screws so that the
setscrews are facing the adjacent door.
Install Handles
NOTE: Handle mounting setscrews are preinstalled inside the
handle.
1. Remove the handles from the packaging inside the
refrigerator, and place them on a soft surface.
A
B
A. Shoulder screws
B. Setscrews inside the handle
3. Firmly push the handle toward the door until the handle base
is flush against the door.
12
INSTALLATION INSTRUCTIONS
4. While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is
engaged in the setscrew.
5. Using a clockwise motion tighten the setscrew just until it
begins to contact the shoulder screw. Do not fully tighten.
6. Repeat steps 4 and 5 to fasten the lower setscrew.
7. Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
8. Repeat steps 2 through 7 to install the other handle onto the
adjacent refrigerator door.
9. With the drawer(s) closed, place the handle onto the shoulder
screws so that the setscrews are facing down toward the
floor.
10. Firmly push the handle toward the drawer until the handle
base is flush against the drawer.
11. Insert the short end of the hex key into the left-hand hole and
slightly rotate the hex key until it is engaged in the setscrew.
12. Using a left to right motion tighten the setscrew a quarter-turn
at a time just until it begins to contact the shoulder screw. Do
not fully tighten.
13. Repeat steps 11 and 12 to fasten the right-hand setscrew to
the shoulder screw.
14. Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.
IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
15. For some models, repeat steps 9 through 14 to install a
handle on the second drawer.
16. Save the hex key and all instructions.
Remove the Handles
A
B
1. While holding the handle, insert the short end of the hex key
into a setscrew hole and slightly rotate the hex key until it is
engaged in the setscrew.
2. Using a right to left motion loosen the setscrew a quarter-turn
at a time.
3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the
handle away from the door or drawer.
4. If necessary, use a Phillips screwdriver to remove the
shoulder screws from the door.
A. Shoulder screw
B. Setscrews inside the handle
13
INSTALLATION INSTRUCTIONS
Refrigerator Leveling, Door Closing and Alignment
The base grille covers the adjustable brake feet and roller
assemblies located at the bottom of the refrigerator below the
freezer drawer. Before making any adjustments, remove the base
grille and move the refrigerator to its final location.
Tools Needed: ¹⁄₄" hex driver
Tools Provided: ¹⁄₈" hex key wrench
1. Remove the base grille. Grasp the grille firmly and pull it
toward you. Open the freezer drawer to access the brake
feet.
NOTE: To allow the refrigerator to roll easier, raise the break
feet by turning them counterclockwise. The front rollers will
be touching the floor.
Style 2
¹⁄₄"
A
A. Brake foot
5. Make sure the doors are even at the top and that the space
between the bottom of the refrigerator doors and the top of
the freezer drawer is even. If necessary, align the doors.
To Align the Doors:
2. Move the refrigerator to its final location.
3. Lower the brake feet, by turning them clockwise, until the
rollers are off the floor and both brake feet are snug against
the floor. This keeps the refrigerator from rolling forward when
opening the refrigerator doors or freezer drawer.
IMPORTANT: If you need to make further adjustments
involving the brake feet, you must turn both brake feet the
same amount to keep the refrigerator level.
4. Make sure the doors close easily. If you are satisfied with the
door opening and closing, skip the next section and go to
“Align the Doors.” If, however, the doors do not close easily
or the doors pop open, adjust the tilt.
To Adjust the Cabinet Tilt:
■
■
Keeping both refrigerator doors closed, pull out the
freezer drawer. Locate the bottom hinge pin of the
right-hand refrigerator door. The alignment screw is inside
the bottom hinge pin.
■
Insert the short end of the ¹⁄₈" hex key wrench (packed
with the Door Handle Installation Instructions) into the
bottom hinge pin until it is fully engaged in the alignment
screw.
■
To raise the refrigerator door, turn the hex key to the right.
To lower the door, turn the hex key to the left.
Continue to turn the alignment screw until the doors are
aligned.
Open the freezer drawer. Use a ¹⁄₄" hex driver to turn both
brake feet clockwise the same amount. This will raise the
front of the refrigerator. It may take several turns to allow
the doors to close easier.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the brake feet. This
makes it easier to turn them.
Style 1
A
¹⁄₄"
B
A. Bottom hinge pin
B. ¹⁄₈" Hex key wrench
A
B
A. Brake foot
B. Front roller
14
6. Make sure the refrigerator is steady. If the refrigerator seems
unsteady or rolls forward when the door or drawer is pulled
open, adjust the brake feet.
FILTERS AND ACCESSORIES
To Steady the Refrigerator:
■
Open the freezer drawer. Using a ¹⁄₄" hex driver, turn both
brake feet clockwise the same amount until the brake feet
are snug against the floor. Check again. If not satisfied,
continue to adjust the brake feet by half turns of the
screw until the refrigerator does not roll forward when the
drawer is opened.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the brake feet. This
makes it easier to turn the screws.
7. Replace the base grille by aligning the ends of the grille with
the leveling assemblies on each side and snapping the grille
into place.
Water Filtration System
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
4. Align the arrow on the water filter label with the cutout notch
in the filter housing and insert the filter into the housing.
5. Turn the filter clockwise 90 degrees (¹⁄₄ turn), until it locks into
the housing.
NOTE: If the filter is not correctly locked into the housing, the
water dispenser will not operate. Water will not flow from the
dispenser.
Install the Water Filter
1. Locate the accessory packet in the refrigerator and remove
the water filter.
2. Take the water filter out of its packaging and remove the
cover from the O-rings. Be sure the O-rings are still in place
after the cover is removed.
A
B
A. O-ring cover
B. O-rings
3. The water filter compartment is located in the right-hand side
of the refrigerator ceiling. Push up on the compartment door
to release the catch, then lower the door.
6. While the compartment door is still open, lift the filter up into
the compartment. Then, close the filter compartment door
completely.
7. Flush the water system. See “Flushing the Water Filter” in the
“Water and Ice Dispensers” section.
IMPORTANT: If you do not flush the water system, you may
experience dripping and/or decreased flow from the water
dispenser.
The Water Filter Status Light
Press OPTIONS on the control panel to launch the Options menu.
Press OPTIONS, under Filter Status, again to display the
percentage of filter life remaining (from 99% to 0%). Press ICE/
WATER, under Back, to return to the Normal screen.
The water filter status lights will help you know when to change
your water filter.
■ ORDER FILTER (yellow) - it is almost time to change the water
filter. While you are dispensing water, “Order Filter” will blink
seven times and sound an alert tone three times.
■
REPLACE FILTER (red) - Replace the water filter. While you
are dispensing water, “Replace Filter” will blink seven times
and an alert tone will sound three times.
15
FILTERS AND ACCESSORIES
RESET the water filter status tracking feature. After you
replace the disposable filter with a new filter, closing the filter
compartment door will automatically reset the filter status
tracking feature. See “Using the Control(s).”
■
NOTE: “REPLACE FILTER” will remain illuminated if a filter is
not installed or is installed incorrectly.
Replace the Water Filter
1. Locate the water filter compartment in the right-hand side of
the refrigerator ceiling. Push up to release and lower the
compartment door.
2. Turn the water filter counterclockwise (to the left), and pull it
straight out of the compartment.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
3. Install the replacement water filter by following steps 2
through 7 in the “Install the Water Filter” section.
To purchase a replacement water filter, see “Accessories” in the
User Guide, Use and Care Guide or User Instructions.
Replace the disposable water filter when indicated on the water
filter status display or at least every 6 months. If water flow to
your dispenser or ice maker decreases noticeably, change the
water filter sooner.
Install Air Filter
(on some models)
An air filter is 15 times more powerful than baking soda at
reducing common food odors inside the refrigerator.
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use.
Installing the Air Filter
Install the air filter behind the vented door, located on the rear
wall near the top of the refrigerator compartment.
1. Remove the air filter from its packaging.
2. Lift open the vented door.
3. Snap the filter into place.
Installing the Filter Status Indicator
The filter comes with a status indicator, which should be
activated and installed at the same time the air filter is installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator until
the bubble pops to activate the indicator.
3. Lift open the vented air filter door. On some models, there are
notches behind the door.
Models with notches:
■
■
With the indicator screen facing outward, slide the
indicator down into the notches.
NOTE: The indicator will not easily slide into the notches
if the bubble has not been popped.
Close the air filter door, and check that the indicator is
visible through the window in the door.
A
A
B
A. Air filter
C
A. Status indicator window
B. Air filter status indicator
C. Notches
16
FILTERS AND ACCESSORIES
Models without notches:
Place the indicator somewhere it is easily visible - either
inside the refrigerator, or elsewhere in your kitchen or
home.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months,
when the status indicator has completely changed from white to
red.
(on some models)
High
Very High
Asparagus
Med.
Very Low
Berries
Low
Low
Broccoli
High
Very Low
Cantaloupe
Med.
High
Carrots
Low
Very Low
Citrus Fruit
Med.
Very Low
Grapes
Low
Very Low
Lettuce
High
Very Low
Pears
High
Very High
Spinach
High
Very Low
Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.
1. Find the Produce Preserver housing inside the refrigerator.
IRRITANT
Apples
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.
ATTENTION
Ethylene
Production
CAUTION: IRRITANT
Lisez des prudences sur le revers.
Sensitivity to
Ethylene
Installing the Produce Preserver
IRRITANT
The produce preserver absorbs ethylene, to slow the ripening
process of many produce items. As a result, certain produce
items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
CAUTION
Install Produce Preserver
Read cautions on back.
■
To order a replacement air filter, contact us. See “Accessories” in
the User Guide, Use and Care Guide or User Instructions for
information on ordering.
1. Remove the used air filter by squeezing in on the side tabs.
2. Remove the used status indicator.
3. Install the new air filter and filter status indicator using the
instructions in the previous sections.
2. Open the housing by pulling up and out on the back.
3. Remove the Produce Preserver pouches from the packaging
and place them into the housing.
NOTE: For best performance, always use two pouches.
4. Adhere the Produce Preserver housing to the back wall of the
crisper drawer according to the instructions included in the
package.
17
FILTERS AND ACCESSORIES
Installing the Status Indicator
The produce preserver comes with a status indicator, which
should be activated and installed at the same time the pouches
are installed.
3. Slide open the cap on the top of the produce preserver
housing.
4. Place the indicator in the top of the housing, facing outward.
5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.
NOTE: The cap will not easily close if the indicator’s bubble
has not been popped.
Replacing the Produce Preserver
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator until
the bubble pops, to activate the indicator.
The disposable pouches should be replaced every 6 months or
when the status indicator changes completely from white to red.
To order replacements, contact us. See “Accessories” for
information on ordering.
1. Remove the used pouches from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the replacement pouches and status indicator using
the instructions in the previous sections.
Accessories
The following accessories are available for your refrigerator. To
order an accessory, contact us and ask for the Part Number.
In the U.S.A., visit our webpage www.whirlpool.com/
accessories or call 1-800-901-2042.
In Canada, visit our webpage www.whirlpool.ca
or call 1-800-807-6777.
affresh® Stainless Steel Cleaner:
In U.S.A., order Part #W10355016
In Canada, order Part #W10355016B
affresh® Stainless Steel Wipes:
In U.S.A., order Part #W10355049
In Canada, order Part #W10355049B
18
affresh® Kitchen & Appliance Cleaner:
In U.S.A., order Part #W10355010
In Canada, order Part #W10355010B
Water Filter:
Order Part #W10413645A or FILTER2
Air Filter:
Order Part #W10311524 or AIR1
Produce Preserver:
Order Part # W10346771A or FRESH1
Water Filter, Air Filter and Produce Preserver Bundle Pack:
Order Part # W10413643BL
REFRIGERATOR USE
Opening and Closing Doors
There are two refrigerator compartment doors. The doors can be
opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.
■ When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.
■
A
When both doors are closed, the hinged seal automatically
forms a seal between the two doors.
A. Hinged seal
Using the Controls
The controls are located above the external dispenser.
Viewing and Adjusting Temperature Set Points
For your convenience, your refrigerator and freezer controls are
preset at the factory.
When you first install your refrigerator, make sure that the
controls are still set to the recommended set points. The factory
recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IMPORTANT:
■ Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
IMPORTANT: The display screen on the dispenser control panel
will turn off automatically and enter “sleep” mode when the
control buttons and dispenser paddles have not been used for
2 minutes or more. Press any control button to reactivate the
display screen. The home screen will appear as shown.
NOTE: Adjusting the set points to a colder than
recommended setting will not cool the compartments any
faster.
■
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
■
The recommended settings should be correct for normal
household use. The controls are set correctly when milk or
juice is as cold as you like and when ice cream is firm.
NOTE: Areas such as a garage, basement or porch, may
have higher humidity or extreme temperatures. You may need
to adjust the temperature away from the recommended
settings to accommodate for these conditions.
■
Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
View Temperature Set Points
1. Press and hold TEMP for 3 seconds to activate Temperature
mode.
NOTE: To view temperature in degrees Celsius, press the
LIGHT button, under Units, when adjust mode is activated. To
return the display setting to Fahrenheit, press the LIGHT
button again.
19
REFRIGERATOR USE
When adjusting temperature set points,
use the following chart as a guide:
When Temperature mode is activated, press TEMP to toggle
between Fridge and Freezer. The display will show the
temperature set point of the selected compartment, and
temperature adjusting information will appear on the display
screen.
Recommended Refrigerator Temperature
CONDITION:
TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold
REFRIGERATOR Setting
1° higher
REFRIGERATOR too warm
REFRIGERATOR Setting
1° lower
FREEZER too cold
FREEZER Setting
1° higher
FREEZER too warm /
Too little ice
FREEZER Setting
1° lower
Cooling On/Off
Recommended Freezer Temperature
Your refrigerator and freezer will not cool when cooling is
turned off.
■ To turn cooling off, press and hold the LOCK and
MEASURED FILL buttons at the same time for 3 seconds.
The Cooling Off icon will blink seven times and then remain lit
as shown.
IMPORTANT:
■ To avoid unintentionally locking the dispenser or changing
other settings, press both buttons at exactly the same
time.
■ When cooling is off, the dispenser paddles and all
controls except Lock and Measured Fill are disabled.
Adjust Temperature Set Points
Refrigerator set point range: 33°F to 45°F (0°C to 7°C).
Freezer set point range: -5°F to 5°F (-21°C to -15°C).
1. When Temperature mode is activated, press TEMPERATURE
to select the Refrigerator zone. The display will show the
temperature set point of the selected compartment, as
shown.
2. Press LOCK to raise the set point, or press OPTIONS to lower
the set point.
3. When you have finished viewing (and adjusting if desired) the
refrigerator set point, press TEMP, under Select Zone, to
change the display to show the freezer set point. When the
zone has been changed, “FREEZER” appears on the display
screen.
4. Press the LOCK button to raise the set point, or press the
OPTIONS button to lower the set point.
Save/Confirm Temperature Settings
■
When you have finished adjusting both the refrigerator and
freezer set points, press MEASURED FILL to confirm and to
save the settings.
NOTE: To exit Temperature mode without saving changes, press
the ICE/WATER button under Back at any time, or allow about
60 seconds of inactivity. The temperature mode will turn off
automatically and return to the normal screen.
20
A. Press LOCK and MEASURED FILL at the same time.
■
Press and hold LOCK and MEASURED FILL for 3 seconds
again to turn cooling back on.
Options
Press the OPTIONS button to open the Options menu and select
between Fast Ice, Filter Status or Vacation mode.
Press the ICE/WATER button at any time to return to the Normal
screen.
REFRIGERATOR USE
Fast Ice
■
The Fast Ice feature assists with temporary periods of heavy ice
use by increasing ice production.
■ To turn on the Fast Ice feature, press the OPTIONS button to
access the Options menu, then press TEMP, under Fast Ice to
activate the feature. When the feature is on, the Fast Ice icon
will appear on the dispenser display screen. The Fast Ice
feature will remain on for 24 hours unless manually turned off.
To turn on Vacation mode, press the OPTIONS button to
access the Options menu, then press LOCK, under Vacation,
to activate the feature. When the feature is on, the Vacation
icon will appear on the dispenser display screen as shown.
■
To turn off Vacation Mode, press the OPTIONS button to
access the Options menu, then press LOCK to turn off the
feature. The Vacation icon will disappear, and the screen will
display the settings as they were before Vacation Mode was
turned on.
■
To manually turn off the Fast Ice feature, press the OPTIONS
button to enter Options mode (unless you are already in
Options mode), then press TEMP, under Fast Ice, again.
When the feature has been turned off, the Fast Ice icon will
disappear from the dispenser display.
Filter Status
Displays the percentage of use remaining in the water filter (from
100% remaining to 0% remaining).
To access Filter Status, press the OPTIONS button to access the
Options menu, then press OPTIONS, under Filter Status, to
display the percent of life remaining in the water filter.
ALSO
The water filter status lights will let you know when to change
your water filter.
■ ORDER FILTER (Yellow) - Order a replacement water filter.
■
REPLACE FILTER (Red) - Replace the water filter. Replacing
the disposable water filter will automatically reset the water
filter status tracking feature. See “Water Filtration System.”
NOTE: REPLACE FILTER will remain illuminated if a filter is
not installed or installed incorrectly.
NOTES:
■ During the first hour after Vacation Mode is turned on,
opening and closing the refrigerator door will not affect the
setting. After 1 hour has passed, opening and closing the
refrigerator door will turn off Vacation Mode.
■
While in Vacation Mode, if Fast Ice is turned on or the Door
Ajar alarm sounds, Vacation Mode will be canceled.
Additional Features
Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the
refrigerator door(s) or freezer drawer is open for 5 minutes and
cooling is turned on. The alarm will repeat every 2 minutes. Close
all doors and drawer to turn it off. The feature then is reset and
will reactivate when either door is left open again for 5 minutes.
■ NOTE: To mute the audible alarm while keeping the doors
open, such as while cleaning the inside of the refrigerator,
press any button on the control panel. The alarm sound will
be temporarily turned off, but the Door Ajar icon will still be
displayed on the dispenser control panel.
Disabling Sounds
Vacation Mode
In Vacation Mode, the freezer will defrost less often to conserve
energy.
■
To turn off control and dispenser sounds, press and hold ICE/
WATER and MEASURED FILL at the same time for
3 seconds. All normal operating tones are disabled. Only alert
tones will be audible.
■
To turn all sounds back on, press and hold ICE/WATER and
MEASURED FILL at the same time for 3 seconds again.
Showroom Mode
This mode is used only when the refrigerator is on display in a
retail store. If you unintentionally turn on Showroom mode, the
word “Showroom” will light up on the display. Exit Showroom
mode by pressing and holding LIGHT and LOCK at the same
time for 3 seconds.
Water and Ice Dispensers
IMPORTANT:
■ Allow 3 hours for the refrigerator to cool down and chill water.
■
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
■
The dispensing system will not operate when either the
refrigerator door or freezer drawer is open.
21
REFRIGERATOR USE
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
1. Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.
2. Release the dispenser paddle for 5 seconds. Repeat steps 1
and 2 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total
of 3 gal. (12 L) has been dispensed.
Calibrate Measured Fill
Household water pressure may affect the accuracy of the
Measured Fill feature. So, for optimum performance of your water
dispenser, you must first calibrate Measured Fill.
IMPORTANT: Flush the water system before calibrating
Measured Fill.
1. Place a sturdy measuring cup (1 cup [237 mL] size) on the
dispenser tray centered in front of the ice/water dispenser
paddle.
NOTE: Depending on your model, a measuring cup may be
provided.
A
3. Press and release the ice/water dispenser paddle, as needed,
to dispense water to the 1 cup fill line.
NOTE: If overfilling or spilling occurs, discard the water and
press ICE/WATER “Back” to restart the calibration process.
4. When 1 cup of water has been correctly dispensed into the
measuring cup, press the MEASURED FILL button under the
word “Confirm” to confirm the calibration.
B
A. Ice/Water dispenser paddle
B. Measuring cup (1 cup)
2. Press and hold the OPTIONS and LOCK buttons at the same
time for 3 seconds. The words “Back” and “1 Cup” will
appear on the display screen. Also, the Calibrate Measured
Fill icon will illuminate and remain lit while the Measured Fill
feature is being calibrated.
NOTE: You may press ICE/WATER “Back” at any time to exit
calibration mode. The Calibrate Measured Fill icon will
disappear.
22
A
A. 1 cup of water
5. When Measured Fill calibration has been confirmed the icons
will disappear and the display will return to the home screen.
REFRIGERATOR USE
To Dispense Water (Measured Fill):
Dispensing
Press ICE/WATER to toggle through the following choices in a
continuous loop:
■ Water (default) - Dispenses water
■
Cubed - Dispenses cubed ice.
■
Crushed - Dispenses crushed ice
Measured Fill allows you to dispense a specified amount of water
with the touch of a few controls.
NOTE: The amount of water you select will be dispensed. Be
sure that the container is empty and can hold the entire volume. If
ice is in the container, you may need to adjust your selection.
1. Press MEASURED FILL to turn on the feature. When the
feature is on, the Measured Fill screen appears on the display.
NOTES:
■
The word “ICE” appears on the display screen when
either crushed or cubed ice is selected.
■
For crushed ice, cubes are crushed before being
dispensed. This may cause a slight delay when
dispensing crushed ice. Noise from the ice crusher is
normal, and pieces of ice may vary in size.
■
When changing from crushed to cubed, a few ounces of
crushed ice will be dispensed along with the first cubes.
NOTES:
Water
Crushed
Cubed
The Water Dispenser
IMPORTANT:
■ Dispense at least 1 qt (1 L) of water every week to maintain a
fresh supply.
■
■
The dispenser will automatically turn off Measured Fill
after 1 minute of inactivity. When Measured Fill is turned
off, any changes you have made will be lost and all
defaults will be restored.
■
Press ICE/WATER “Back,” to manually turn off the
Measured Fill feature.
2. Press LIGHT, under Units, to toggle among ounce, cup and
liter. The default unit is ounce.
Default, minimum, and maximum volumes are listed below.
If the flow of water from the dispenser decreases, it could be
caused by low water pressure.
■
■
With the water filter removed, dispense 1 cup (237 mL) of
water. If 1 cup (237 mL) of water is dispensed in
8 seconds or less, the water pressure to the refrigerator
meets the minimum requirement.
If it takes longer than 8 seconds to dispense 1 cup
(237 mL) of water, the water pressure to the refrigerator is
lower than recommended. See “Water Supply
Requirements” and “Troubleshooting” for suggestions.
3. Remove the glass to stop dispensing.
Default
Minimum
Maximum
Ounces
8
1
128
Cups
1
¹/₄
16
Liters
0.25
0.05
4.00
3. Press LOCK or OPTIONS to adjust the water volume as
desired. The LOCK control increases the volume, and the
OPTIONS control lowers the volume.
NOTES:
■
When increasing or decreasing the dispense volumes, if
an adjustment button (-/+) is held for approximately
10 seconds or longer the control may stop responding.
Release the button for approximately 2 seconds and then
continue making the adjustment.
■
Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]
per cup) are not the same size as a measuring cup (8 oz
[237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
To Dispense Water (Standard):
1. Select water.
2. Press a sturdy glass against the dispenser paddle.
NOTE: While dispensing water and for 3 seconds after
dispensing has stopped, the digital display will show how
much water has been dispensed.
Units
4. Dispense water.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
■
Press a sturdy glass against the dispenser paddle.
■
OR
Place the glass below the water dispenser and press
MEASURED FILL, under Dispense, for hands-free
dispensing.
23
REFRIGERATOR USE
5. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser paddle OR
press MEASURED FILL a second time.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show how
much water remains to be dispensed. The display will turn off
after 1 minute of inactivity.
■
To select a new volume or start dispensing the same
volume again, you must first finish dispensing the
selected volume, or turn off the Measured Fill feature
(either by waiting 1 minute so it will automatically turn off
or by pressing ICE/WATER “Back” to manually turn it off)
and then turn it back on.
The Ice Dispenser
The Dispenser Light
When you use the dispenser, the light will automatically turn on.
To turn on the light when you are not dispensing:
Press LIGHT to toggle through the following choices in a
continuous loop:
■ OFF (default) - The dispenser light is off
■
ON - The dispenser light remains on at 100% brightness
■
DIM - The dispenser light remains on at 50% brightness
The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see
“Troubleshooting” for more information.
IMPORTANT:
■ If the ice cubes are hollow or have an irregular shape, it could
be because of low water pressure. See “Water Supply
Requirements.”
■
Ice travels from the ice storage bin through the dispenser
chute to the dispenser. To turn off the ice maker, see “Ice
Maker and Storage Bin.”
ON
The Dispenser Lock
To Clean the Ice Dispenser Chute:
Humidity causes ice to naturally clump together. Ice particles can
build up until the ice dispenser chute becomes blocked.
If ice is not dispensed regularly, it may be necessary to empty the
ice storage bin and clean the ice delivery chute, the ice storage
bin and the area beneath the storage bin every 2 weeks.
■ Remove the ice clogging the storage bin and delivery chute,
using a plastic utensil if necessary.
■
Clean the ice delivery chute and the bottom of the ice storage
bin using a warm, damp cloth, then dry thoroughly.
DIM
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the
refrigerator, to the ice maker, or to the dispenser light. It simply
deactivates the controls and dispenser paddles. To turn off the
ice maker, see “Ice Maker and Storage Bin.”
■ Press and hold LOCK for 3 seconds to lock the dispenser.
■
Press and hold LOCK a second time to unlock the dispenser.
The display screen indicates when the dispenser is locked.
To Dispense Ice:
1. Select the desired type of ice. To switch between cubed ice
and crushed ice, press ICE/WATER.
WARNING
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
2. Press a sturdy glass against the dispenser paddle. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to
the paddle to activate the ice dispenser. Pressing hard will not
make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for several seconds after
removing the glass from the dispenser paddle. The dispenser may
continue to make noise for a few seconds after dispensing.
24
LOCKED
UNLOCKED
REFRIGERATOR USE
Ice Maker and Ice Storage Bin
(on some models)
IMPORTANT: To avoid low ice production and poor quality ice,
flush the water system before turning on the ice maker. See
“Water Dispenser.”
■ Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Allow 2 to 3 days for the
storage bin to fill completely following installation.
■
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply cannot
be avoided, make sure the water softener is operating
properly and is well maintained.
■
If the ice in the storage bin clumps together, break up ice
using a plastic utensil and discard. Do not use anything sharp
to break up the ice. This can cause damage to the ice bin and
the dispenser mechanism.
■
Do not store anything in the ice storage bin.
NOTES:
■
To manually turn off the ice maker, move the control to the
OFF (right) position.
■
Your ice maker has an automatic shutoff. The sensor will
automatically stop ice production if the storage bin is full,
if the door is open or the storage bin is removed. The
control will remain in the ON (left) position.
A
Ice Production Rate
■
The ice maker should produce approximately 3 lbs (1.4 kg) of
ice per day under normal operation.
■
To increase ice production, select the increased ice
production feature from the Options menu on the control
panel. See “Using the Control(s).”
Style 1 - Ice Maker in the Refrigerator
(on some models)
The ice maker is located on the left-hand side of the refrigerator
compartment ceiling. Ice cubes are ejected into the ice storage
bin, located on the left-hand refrigerator door.
Turn the Ice Maker On/Off
1. Push up on the latch on the left-hand side of the ice
compartment to open the door.
A. Ice storage bin release latch
3. Close the ice compartment door.
Remove and Replace the Ice Storage Bin
■
Remove the ice storage bin by inserting your fingers into the
hole at the base of the bin and squeezing the latch to release
the bin from the compartment. Lift the storage bin up and pull
it straight out.
■
Replace the storage bin inside the ice compartment and push
down to make sure it is firmly in place.
Style 2 - Ice Maker in the Freezer (on some models)
Turn the Ice Maker On/Off
To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.
A
A. Ice compartment door latch
2. Turn on the ice maker by moving the switch to the (left) ON
position.
NOTE: Turn off the ice maker before removing the ice storage bin
to serve ice or to clean the bin. This will keep the ice cubes from
dropping out of the ice maker and into the freezer compartment.
After replacing the ice storage bin, turn on the ice maker.
25
REFRIGERATOR FEATURES
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Refrigerator Shelves
The shelves in your refrigerator are adjustable to meet your
individual storage needs.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. It will also reduce the
amount of time the refrigerator door is open, and save energy.
Shelves and Shelf Frames
Tuck Away Shelf (on some models)
To retract and extend the front section of the shelf:
1. To retract the front-section of the shelf, slightly lift up on the
front edge and push the adjustable portion of the shelf back
toward the rear of the refrigerator.
2. Extend the front of the shelf by pulling the retracted portion of
the shelf outward until it is fully extended.
To remove and replace a shelf/shelf frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it
out of the shelf supports.
2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports. Tilt the front of the shelf up until rear shelf
hooks drop into the shelf supports.
3. Lower the front of the shelf and make sure that the shelf is in
position.
Crisper Drawers/Pantry Drawer/Crisper Cover
To remove and replace the drawers:
1. Slide the drawers straight out to the stop. Lift the drawers
from the rails and pull them out the rest of the way.
2. Replace the drawers by placing them on the rails and pushing
them back into position past the drawer stop.
26
REFRIGERATOR FEATURES
To remove the crisper(s) cover:
1. Remove crisper drawers.
2. Holding the glass insert firmly with one hand, press up in
center of glass insert until it rises above the plastic frame.
Gently slide the glass insert forward to remove.
3. Lift the cover frame up and remove it.
To replace crisper(s) cover:
1. Fit back of cover frame into supports on side walls of the
refrigerator and lower the front of the cover frame into place.
2. Slide rear of glass insert into cover frame and lower front into
place.
3. Replace crisper drawers.
Crisper Humidity Control
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW (open)
and HIGH (closed).
LOW - Move control to the far left-hand side to allow moist air out
of the crisper for best storage of fruits and vegetables with skins.
■ Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.
■
HIGH - Move control to the far right-hand side to keep moist air in
the crisper for best storage of fresh, leafy vegetables.
■ Leafy vegetables: Wash in cold water, drain and trim or tear
off bruised and discolored areas. Place in plastic bag or
plastic container and store in crisper.
Vegetables with skins: Place in plastic bags or plastic
container and store in crisper.
Temperature-Controlled Drawer
IMPORTANT: This control sets the temperature for only this
drawer. It does not set the temperature for, or turn off cooling to
the refrigerator or freezer compartments.
The full-width, temperature-controlled drawer can be used to
store large deli trays, fresh meat, beverages or other items that
you want to store at an optimum temperature.
Depending on your model, you will have either an Electronic
Control or a Manual Control. Use the directions specific to your
model.
NOTE: Do not place leafy vegetables in the temperaturecontrolled drawer. The colder temperatures could damage leafy
produce.
Style 1 - Electronic Control
For your convenience, temperatures have been preset for the
optimum storage of fresh meat and poultry, cold drinks, and deli
and cheese. These preset temperatures cannot be adjusted.
Press the desired temperature setting for the items to be stored
in the drawer. As it is pressed, each icon will light up, and its
corresponding preset temperature will display:
■ Meats/Poultry - 32°F (0°C)
■
Cold Drinks (default setting) - 36°F (2°C)
■
Deli/Cheese - 39°F (4°C)
NOTE: If no button is pressed, the control will revert to Cold
Drinks, the default setting.
Style 2 - Manual Control
Slide the control to the temperature setting best suited for the
items stored in the drawer.
■ Meat - Coldest
■
Vegetables - Least cold
27
REFRIGERATOR FEATURES
Drawer Removal and Replacement
To remove the drawer:
1. Push the drawer completely closed.
2. Lift up the front of the drawer and pull it straight out.
To replace the drawer:
1. Push the metal glide rails to the rear of the refrigerator.
2. Place the drawer onto the glide rails. While tilting the rear of
the drawer upward, slide the drawer toward the rear of the
refrigerator.
Drawer Divider
Meat Storage Guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish......................... use same day as purchased
Chicken, ground beef, variety meats (liver) ...................... 1-2 days
Cold cuts, steaks/roasts .................................................. 3-5 days
Cured meats................................................................... 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
To remove the divider:
1. Pull the drawer out to its full extension.
2. Lift the front of the divider and lift the divider out.
To replace the divider:
1. Position the divider so that the features on the bottom of the
divider align with the matching features in the drawer.
2. Lower the divider into place.
Door Bins
To remove and replace the bins:
1. Remove the bin by lifting it up and pulling it straight out.
2. Replace the bin by sliding it in above the desired support and
pushing it down until it stops.
Pizza Pocket and Drawer Divider
The drawer divider is not removable. For storage flexibility, the
divider can be moved a few inches to either side allowing you to
store larger items in one section of the freezer drawer.
A
B
A. Drawer divider
B. Pizza pocket
28
REFRIGERATOR CARE
Cleaning
WARNING
Style 2 - Stainless Steel
IMPORTANT:
■ Damage to stainless steel finish due to improper use of
cleaning products, or using non-recommended cleaning
products, is not covered under the warranty.
DO USE
Explosion Hazard
✔ Soft, clean cloth
✘
✘
✘
Abrasive cloths
Paper towels or newsprint
Steel-wool pads
✔ Warm, soapy water
✘
✘
✘
✘
Abrasive powders or liquids
Ammonia
Citrus-based cleaners
Acidic or vinegar-based
cleaners
Oven cleaners
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
✘
Exterior Cleaning
Please see the exterior cleaning information specific to your
model.
Style 1 - Smooth Door
IMPORTANT: Damage to smooth finish due to improper use of
cleaning products, or using non-recommended cleaning
products, is not covered under the warranty. Sharp or blunt
instruments will mar the finish.
DO USE
✔ Soft, clean cloth
✔ Warm, soapy water use a mild detergent
DO NOT USE
DO NOT USE
✘
✘
✘
Abrasive cloths
Paper towels or newsprint
Steel-wool pads
✘
✘
✘
✘
Abrasive powders or liquids
Window sprays
Ammonia
Acidic or vinegar based
cleaners
Oven cleaners
Flammable fluids
✘
✘
NOTE: Paper towels scratch and may dull the clear coat of the
painted door. To avoid possible damage use only soft clean
clothes to polish and wipe the door.
✔ For heavy soil, ONLY a
stainless steel cleaner
designed for
appliances. To order
the cleaner, see
“Accessories.”
✘
Stainless steel cleaner is for
stainless steel parts only! Do
not allow the Stainless Steel
Cleaner and Polish to come
into contact with any plastic
parts such as the trim pieces,
dispenser covers or door
gaskets.
NOTES:
■ If unintentional contact does occur, clean plastic part with a
sponge and mild detergent in warm water. Dry thoroughly
with a soft cloth.
■
Just because a cleaner is a liquid does not mean it is
nonabrasive. Many liquid cleansers formulated to be gentle
on tile and smooth surfaces still damage stainless steel.
■
Citric acid permanently discolors stainless steel. To avoid
damaging the finish of your stainless steel refrigerator:
Do not allow these substances to remain on the finish
✘
Mustard
✘
Citrus-based sauces
✘
Tomato juice
✘
Citrus-based products
✘
Marinara sauce
Interior Cleaning
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
NOTE: Do not use abrasive or harsh cleaners such as
window sprays, scouring cleansers, flammable fluids,
cleaning waxes, concentrated detergents, bleaches or
cleansers containing petroleum products on plastic parts,
interior and door liners or gaskets.
3. Plug in refrigerator or reconnect power.
29
REFRIGERATOR CARE
Condenser Cleaning
There is no need for routine condenser cleaning in normal home
operating environments. If the environment is particularly greasy
or dusty, or there is significant pet traffic in the home, the
condenser should be cleaned every 2 to 3 months to ensure
maximum efficiency.
If you need to clean the condenser:
1. Unplug refrigerator or disconnect power.
2. Remove the base grille.
3. Use a vacuum cleaner with a soft brush to clean the grille, the
open areas behind the grille and the front surface area of the
condenser.
4. Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.
Lights
The lights in both the refrigerator and freezer compartments are LEDs which do not need to be replaced. If the lights do not illuminate
when the door or drawer is opened, call for assistance or service. In the U.S.A., call 1-800-253-1301. In Canada call 1-800-807-6777.
Vacation and Moving Care
Vacations
If You Choose to Leave the Refrigerator On While
You’re Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker, and is
connected to the household water supply, turn off the water
supply to the refrigerator. Property damage can occur if the
water supply is not turned off.
3. If you have an automatic ice maker, turn off the ice maker.
NOTE: Depending on your model, raise the wire shutoff arm
to OFF (up) position, or press the switch to OFF.
4. Empty the ice bin.
If You Choose to Turn Off the Refrigerator Before You
Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
■ Turn off the water supply to the ice maker at least one day
ahead of time.
■
When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position or press the switch to OFF,
depending on your model.
3. Turn off the Temperature control(s). See “Using the
Control(s).”
4. Clean refrigerator, wipe it, and dry well.
5. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.
30
Moving
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
■ Turn off the water supply to the ice maker at least one day
ahead of time.
■
Disconnect the water line from the back of the
refrigerator.
■
When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position or press the switch to OFF,
depending on your model.
2. Remove all food from the refrigerator and pack all frozen food
in dry ice.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See “Using the
Control(s).”
5. Unplug refrigerator.
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
8. Depending on the model, raise the front of the refrigerator so
it rolls more easily OR raise the leveling screws so they don't
scrape the floor. See “Adjust the Door(s)” or “Door Closing
and Door Alignment.”
9. Tape the doors closed and tape the power cord to the back of
the refrigerator.
When you get to your new home, put everything back and refer to
the “Installation Instructions” section for preparation instructions.
Also, if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.
TROUBLESHOOTING
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty page in this manual and scan the code with your mobile device, or visit https://whirlpool.custhelp.com.
Contact us by mail with any questions or concerns at the address below:
In Canada:
In the U.S.A.:
Whirlpool Brand Home Appliances
Whirlpool Brand Home Appliances
Customer eXperience Centre
Customer eXperience Center
200 – 6750 Century Ave.
553 Benson Road
Mississauga, Ontario L5N 0B7
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Operation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The refrigerator will not
operate
Check electrical supply
Plug the power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Make sure there is power to the outlet. Plug in a lamp to see
if the outlet is working.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Check controls
Make sure the controls are turned on. See “Using the
Control(s).”
New installation
Allow 24 hours following installation for the refrigerator to
cool completely.
NOTE: Adjusting the temperature controls to the coldest
setting will not cool either compartment more quickly.
Refrigerator control is in Showroom
mode (on some models)
If the refrigerator is in Showroom mode, cooling is turned off
and “Showroom” will be illuminated on the control panel. See
“Using the Control(s)” for more information.
31
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The motor seems to run
too much
High efficiency compressor and fans
Larger, more efficient refrigerators run longer at lower, more
energy efficient speeds.
The room or outdoor temperature is
hot.
It is normal for the refrigerator to work longer under these
conditions. For optimum performance, place the refrigerator
in an indoor, temperature controlled environment. See
“Location Requirements.”
A large amount of warm food has
been recently added.
Warm food will cause the refrigerator to run longer until the
air cools to the desired temperature.
The door(s) are opened too frequently
or for too long.
Warm air entering the refrigerator causes it to run more.
Open the door less often.
The refrigerator door or freezer drawer
is ajar.
Make sure the refrigerator is level. See “Door Closing and
Door Alignment.” Keep food and containers from blocking
the door.
The refrigerator control is set too cold. Adjust the refrigerator control to a less cold setting until the
refrigerator temperature is as desired.
The lights do not work
Pantry Temperature
Control not lit/
unresponsive
The door or drawer gasket is dirty,
worn, or cracked.
Clean or change the gasket. Leaks in the door seal will cause
the refrigerator to run longer in order to maintain desired
temperatures.
Your refrigerator is equipped with LED
lighting which does not need to be
replaced.
If there is power to the refrigerator and the lights do not
illuminate when a door or drawer is opened, call for service
or assistance.
The dispenser light is set to OFF
On some models, the dispenser light will operate only when
a dispenser paddle is pressed. If you want the dispenser light
to stay on continuously, see “Water and Ice Dispensers.”
Doors have been open longer than
10 minutes
Close the doors and drawer to reset, and open to resume
lighted task.
The refrigerator is in Cooling Off mode Exit Cooling Off mode. See “Using the Control(s).”
The refrigerator controls’ initialization
process did not complete
successfully.
Unplug the refrigerator, wait 5 seconds. Plug in the
refrigerator, and wait 30 seconds before opening any of the
refrigerator doors or touching the control panel.
Noise
To listen to normal refrigerator sounds, go to the Product Help/FAQ section of the brand website and search for “normal sounds.”
PROBLEM
POSSIBLE CAUSES
The refrigerator seems
noisy
Below are listed some normal
sounds with explanations.
The compressor in your new refrigerator regulates
temperature more efficiently while using less energy, and
operates quietly. Due to this reduction in operating noise you
may notice unfamiliar noises that are normal.
SOLUTIONS
Sound of the compressor
High-efficiency compressor and fans
running longer than expected
Larger, more efficient refrigerators run
longer at lower, more energy efficient
speeds.
Pulsating/Whirring
Fans/compressor adjusting to optimize performance during
normal compressor operation
This is normal.
Popping
Contraction/expansion of inside walls, especially during
initial cool-down
This is normal.
Hissing/Dripping
Flow of refrigerant, or flow of oil in the compressor
This is normal.
32
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
Vibration
The refrigerator may not be steady
Adjust the leveling screws and lower
the leveling foot firmly against the
floor. See “Door Closing and Door
Alignment.”
Rattling/Banging
Movement of the water lines against the refrigerator cabinet,
or of items placed on top of the refrigerator cabinet
Move excess water line away from the
refrigerator cabinet or fasten excess
tubing to the cabinet. See
“Connecting the Water,” or remove
items from the top of the refrigerator.
Sizzling
Water dripping on the heater during defrost cycle
This is normal.
Water running/Gurgling
May be heard when ice melts during the defrost cycle and
water runs into the drain pan
This is normal.
Buzzing and Clicking
Heard when the water valve opens and closes to dispense
water and/or fill the ice maker.
If the refrigerator is connected to a
water line, this is normal.
If the refrigerator is not connected to a
water line, turn OFF the ice maker.
Repetitive Clicking
Dual evaporator valve regulating the cooling operation
You may hear rapid repetitive clicking
sounds as the unit switches from
cooling one compartment to cooling
the other. This sound is normal.
Creaking/Cracking/Grinding
May be heard as ice is being ejected from the ice maker
mold
This is normal.
Clatter
May be heard when the ice falls into the ice storage bin
This is normal.
Temperature and Moisture
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
Temperature is too warm
The refrigerator has just been
installed.
Allow 24 hours following installation for the refrigerator to
cool completely.
Cooling is turned off.
Turn on cooling. See “Using the Control(s).”
The controls are not set correctly for
the surrounding conditions.
Adjust the controls a setting colder. Check the temperature in
24 hours. See “Using the Control(s).”
The door(s) are opened often or not
closed completely.
Allows warm air to enter refrigerator. Minimize door openings
and keep doors fully closed.
A large load of food was recently
added.
Allow several hours for refrigerator to return to normal
temperature.
Temperature is too cold in
the refrigerator/crisper
Temperature is too cold in
the pantry drawers
The refrigerator air vent(s) are blocked. If the air vent located in the top, left, rear corner of the
refrigerator compartment is blocked by items placed directly
in front of it, the refrigerator will get too cold. Move items
away from the air vent.
The controls are not set correctly for
the surrounding conditions.
Adjust the controls a setting warmer. Check the temperature
in 24 hours. See “Using the Control(s).”
The ice storage bin is not in the
correct position.
See “Ice Maker and Ice Storage Bin.”
The control is not set correctly for the
items stored in drawer.
Adjust the temperature setting. See “Temperature Controlled
Drawer” in the “Refrigerator Features” section.
33
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
There is interior moisture
buildup
NOTE: Some moisture
buildup is normal.
The room is humid
A humid environment contributes to moisture buildup.
The door(s) are opened often or not
closed completely.
Allows humid air to enter the refrigerator. Minimize door
openings and close doors completely.
The door is blocked open
Move food packages away from door.
A bin or shelf is in the way
Push bin or shelf back into the correct position.
Storing liquid in open containers
This adds humidity to the refrigerator interior. Keep all
containers tightly covered.
The drawer is opened often or left
open.
Minimize drawer openings and close drawer completely after
use.
Poor door seal
Ensure door seals are making full contact with the
refrigerator cabinet to allow for an adequate seal.
Temperature controls are not set
correctly
See “Using the Control(s)” for recommended temperature
settings.
There is frost/ice buildup in
the freezer compartment
Ice and Water
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The ice maker is not
producing ice or is not
producing enough ice
The refrigerator is not connected to a
water supply or the water supply shutoff
valve is not turned on.
Connect refrigerator to water supply and turn water shutoff
valve fully open.
There is a kink in the water source line.
A kink in the line can reduce water flow. Straighten the water
source line.
The ice maker is not turned on.
Make sure the ice maker is on. See “Ice Maker and
Ice Storage Bin.”
The refrigerator has just been installed.
Wait 24 hours after ice maker installation for ice production to
begin. Wait 3 days for full ice production.
The refrigerator door is not closed
completely.
Close the door firmly. If it does not close completely, see “The
doors will not close completely.”
A large amount of ice was recently
removed.
Allow sufficient time for ice maker to produce more ice. See
“Ice Maker and Ice Storage Bin” for ice production rates.
An ice cube is jammed in the ice maker
ejector arm.
Remove ice from the ejector arm with a plastic utensil.
A water filter is installed on the
refrigerator.
Remove the water filter and operate the ice maker. If ice
volume improves, then the filter may be clogged or incorrectly
installed. Replace filter or reinstall it correctly.
A reverse osmosis water filtration system
is connected to your cold water supply.
This can decrease water pressure. See “Water Supply
Requirements.”
The water shutoff valve is not fully open.
Turn the water shutoff valve fully open.
There is a kink in the water source line.
A kink in the line can reduce water flow. Straighten the water
source line.
A water filter is installed on the
refrigerator.
Remove filter and operate ice maker. If ice quality improves,
then the filter may be clogged or incorrectly installed. Replace
filter or reinstall it correctly.
A reverse osmosis water filtration system
is connected to your cold water supply.
This can decrease water pressure. See “Water Supply
Requirements.”
Questions remain regarding water
pressure.
Call a licensed, qualified plumber.
The ice cubes are
hollow or small
NOTE: This is an
indication of low water
pressure.
34
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
Off-taste, odor or gray
Newly installed refrigerator requires flush
color in the ice or water of water system.
The water and ice
dispenser will not
operate properly
SOLUTIONS
Flush the water system. See “Water and Ice Dispensers” for
water system flushing instructions.
Recently installed or replaced plumbing
connections. New plumbing connections
can cause discolored or off-flavored ice
and water.
Discard the ice and wash the ice storage bin. Flush the water
system with 3 gal. (12 L) of water. Allow 24 hours for the ice
maker to make new ice, and discard the first 3 batches of ice
produced.
Using a water supply connection type
other than recommended.
It is recommended to use copper tubing or Whirlpool supply
line, Part Number 8212547RP. See “Connect to Water Line.”
The ice has been stored too long.
Discard ice. Wash ice storage bin. Allow 24 hours for ice
maker to make new ice.
The water has been stored too long.
Dispense at least 1 qt (1 L) of water per week to maintain a
fresh supply.
Odor from stored food has transferred to
the ice.
Use airtight, moisture proof packaging to store food.
There are minerals (such as sulfur) in the
water.
A water filter may need to be installed to remove the minerals.
There is a water filter installed on the
refrigerator.
Gray or dark discoloration in ice may indicate that the water
filtration system needs additional flushing. Flush the water
system after installing and before using a new water filter. See
“Water and Ice Dispensers” for water filter flushing
instructions.
The water filter needs to be replaced.
Replace the disposable water filter at least every 6 months or
when indicated. See “Water Filtration System.”
The refrigerator is not connected to a
water supply or the water supply shutoff
valve is not turned on.
Connect the refrigerator to the water supply and turn the water
shutoff valve fully open.
There is a kink in the water source line
A kink in the water line can reduce water flow from the water
dispenser and result in hollow or irregular shaped ice.
Straighten the water source line.
The refrigerator has just been installed.
Flush and fill the water system. See “Water and Ice
Dispensers.”
The water pressure to the house is not at
or above 35 psi (241 kPa).
The water pressure to the house determines the flow from the
dispenser. See “Water Supply Requirements.”
A reverse osmosis water filtration system
is connected to your cold water supply.
A reverse osmosis water filtration system can decrease water
pressure. See “Water Supply Requirements.”
The water filter may be clogged.
Remove the water filter and operate dispenser. If water flow
increases, your filter is clogged and needs to be replaced. See
“Water Filtration System.”
The water filter is installed incorrectly
Remove the water filter and reinstall. See “Water Filtration
System.”
The refrigerator door or freezer drawer is
not closed completely.
Close the door or drawer firmly. If it does not close completely,
see “The doors will not close completely.”
The refrigerator doors were recently
removed.
Make sure the water dispenser wire/tube assembly has been
properly reconnected at the top of the refrigerator door.
See “Refrigerator Doors and Drawer.”
Ice is clogged in the ice storage bin or ice
is blocking the ice delivery chute.
Remove the ice clogging the storage bin and delivery chute,
using a plastic utensil if necessary. Clean the ice delivery chute
and the bottom of the ice storage bin using a warm, damp
cloth, then dry both thoroughly. To avoid clogging and to
maintain a fresh supply of ice, empty the storage bin and clean
both the storage bin and delivery chute every 2 weeks.
35
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The ice dispenser jams
while dispensing
crushed ice
Crushed ice is blocking the ice delivery
chute.
Switch from crushed ice to cubed ice to clear the ice
dispenser. Then switch back to crushed ice.
Water is leaking or
dripping from the
dispenser system
NOTE: A few drops of
water after dispensing is
normal.
The glass was not held under the
dispenser long enough.
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
Water continues to drip
from the dispenser
beyond the first few
drops.
The refrigerator has just been installed.
Flushing the water system removes the air from the lines which
causes the water dispenser to drip. Flush the water system.
See “Water and Ice Dispensers.”
The water filter was recently installed or
replaced.
Flushing the water system removes the air from the lines which
causes the water dispenser to drip. Flush the water system.
See “Water and Ice Dispensers.”
Water is leaking from
the back of the
refrigerator
The water line connections were not fully
tightened.
See “Connecting the Water.”
Recently removed the doors and did not
fully tighten water line connection
See “Refrigerator Doors and Drawer.”
Water from the
dispenser is warm
Water from the dispenser is chilled to
50°F (10°C).
This is normal.
The refrigerator has just been installed.
Allow 24 hours after installation for the water supply to cool
completely.
A large amount of water was recently
dispensed.
Allow 3 hours for the water supply to cool completely.
Water has not been recently dispensed.
The first glass of water may not be cool. Discard the first glass
of water dispensed.
The refrigerator is not connected to a
cold water pipe.
Make sure the refrigerator is connected to a cold water pipe.
See “Water Supply Requirements.”
Doors
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
To view an animation showing how to adjust and align the doors, refer to the Product Help/FAQ section of the brand website and search
for “door closing and door alignment.”
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The doors will not close
completely
The door is blocked open.
Move food packages away from door.
A bin or shelf is in the way.
Push bin or shelf back into the correct position.
Recently installed
Remove all packaging materials.
36
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The doors are difficult to
open
The door gaskets are dirty or sticky.
Clean gaskets and contact surfaces with mild soap and
warm water. Rinse and dry with soft cloth.
The doors appear to be
uneven
The doors need to be aligned, or the
refrigerator needs to be leveled.
See “Refrigerator Leveling, Door Closing and Alignment.”
The refrigerator is unsteady
or it rolls forward when
opening and closing doors
The refrigerator brake feet are not
snug against the floor
Remove the base grille. Turn both brake feet (one on each
side) clockwise, the same amount, until they are snug against
the floor. See “Refrigerator Leveling, Door Closing and
Alignment.”
37
PERFORMANC E DATA SHEET
Water Filtration System
Model P9WB2L/P9RFWB2L Capacity 200 Gallons (757 Liters)
System tested and certified by NSF International against NSF/ANSI
Standard 42, Standard 53, Standard 401, and CSA B483.1 for
the reduction of contaminants specified on the Performance
Data Sheet.
This system has been tested according to NSF/ANSI Standards 42, 53, 401, and CSA B483.1 for the reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible
limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53, 401, and CSA B483.1.
Substance Reduction Aesthetic Effects Influent Challenge Concentration Maximum Permissable
Product Water Concentration
50% reduction
Chlorine Taste/Odor
2.0 mg/L ± 10%
Particulate Class I*
At least 10,000 particles/mL
85% reduction
Influent Challenge Concentration Maximum Permissable
Contaminant Reduction
Product Water Concentration
Lead: @ pH 6.5/@ pH 8.5
0.15 mg/L ± 10%
0.01 0 mg/L
Benzene
0.015 mg/L ± 10%
0.00 5 mg/L
p-Dichlorobenzene
0.225 mg/L ± 10%
0.07 5 mg/L
Carbofuran
0.08 mg/L ± 10%
0.040 mg/L
Toxaphene
0.015 ± 10%
0.00 3 mg/L
Atrazine
0.009 mg/L ± 10%
0.00 3 mg/L
Asbestos
10 7 to 108 fibers/L††
99%
50,000/L min.
99.95%
Live Cysts†
Turbidity
11 NTU ± 10%
0.5 NTU
0 . 0 0 0 2 m g /L
Lindane
0.002 ± 10%
Tetrachloroethylene
0.015 mg/L ± 10%
0.00 5 mg/L
O-Dichlorobenzene
1.8 mg/L ± 10%
0.60 mg/L
Ethylbenzene
2.1 mg/L ± 10%
0.70 mg/L
1,2,4 - Trichlorobenzene
0.210 mg/L ± 10%
0 . 07 m g/L
2,4 - D
0.210 mg/L ± 10%
0.07 mg/L
Styrene
2.0 mg/L ± 10%
0.1 mg/L
Toluene
3.0 mg/L ± 10%
1.0 mg/L
Endrin
0.006 mg/L ± 10%
0.00 2 mg/L
Atenolol
200 ± 20%
30 ng/L
Trimethoprim
140 ± 20%
20 ng/L
Linuron
140 ± 20%
20 ng/L
Estrone
140 ± 20%
20 ng/L
Nonylphenol
1400 ± 20%
200 ng/L
Average% Reduction
97.0%
>99.9%
Average%Reduction
>99.3% / 98.6%
93.8%
99.8%
8 1. 9 %
>95%
87.0%
>99%
>99.99%
96.9%
>99.2%
96.6%
92.3%
86.9%
>99.8%
88.5%
99.6%
93.5%
81.7%
95.7%
96.1%
96.3%
95.3%
95.5%
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.75 gpm (2.84 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to
22°C). Rated service capacity = 200 gallons (757 liters).
The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/incidental
contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these
compounds can affect the public acceptance/perception of drinking water quality.
It is important that operational, maintenance, and filter replacement
Do not use with water that is microbiologically unsafe or of unknown
requirements be carried out for the product to perform as advertised.
quality without adequate disinfection before or after the system.
Property damage can occur if all instructions are not followed.
Systems certified for cyst reduction may be used on disinfected
waters that may contain filterable cysts.
The disposable cartridge must be changed at least every 6 months.
EPA Est. No. 082047-TWN-001
Use replacement filter P9RFWB2L, part #EDR2RXD1/EDR2RXD1B.
Refer to the “Warranty” section (in the User Instructions or User
2015 suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices
Guide) for the Manufacturer’s limited warranty, name and telephone
are subject to change without notice.
number.
The filter monitor system measures the amount of water that passes
Application Guidelines/Water Supply Parameters
through the filter and alerts you when it is time to replace the filter.
Refer to the “Using the Controls” or “Water Filtration System” section
Water Supply
Potable City or Well
(in the User Instructions or User Guide) to learn how to check the
Water Pressure
30 - 120 psi (207 - 827 kPa)
water filter status.
Water Temperature
33° - 100°F (0.6° - 37.8°C)
After changing the water filter, flush the water system. See “Water
Service Flow Rate
0.75 gpm (2.84 L/min.) @ 60 psi
and Ice Dispensers” or “Water Dispenser” in the User Instructions or
User Guide.
These contaminants are not necessarily in your water supply. While
testing was performed under standard laboratory conditions, actual
performance may vary.
The product is for cold water use only.
The water system must be installed in compliance with state and
local laws and regulations.
*Class I particle size: >0.5 to <1 um
†
Based on the use of Cryptosporidium parvum oocysts
Fibers greater than 10 um in length
® NSF is a registered trademark of NSF International.
††
38
WHIRLPOOL
MAJOR APPLIANCE
LIMITED WARRANTY
®
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
Name, address and telephone number
Model number and serial number
A clear, detailed description of the problem
Proof of purchase including dealer or retailer name and address
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some
questions can be addressed without service. Please take a few minutes to review the Troubleshooting or
Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional
resources, or visit www.whirlpool.com/product_help.
2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and
Canada, direct all requests for warranty service to:
www.whirlpool.com/product_help
Whirlpool Customer eXperience Center
In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
For one year from the date of purchase, when this
major appliance is installed, operated and maintained
according to instructions attached to or furnished with
the product, Whirlpool Corporation or Whirlpool
Canada LP (hereafter “Whirlpool”) will pay for Factory
Specified Replacement Parts and repair labor to
correct defects in materials or workmanship that
existed when this major appliance was purchased, or
at its sole discretion replace the product. In the event
of product replacement, your appliance will be
warranted for the remaining term of the original unit's
warranty period.
1. Commercial, non-residential, multiple-family use, or use inconsistent with published
user, operator or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation, installation not in
accordance with electrical or plumbing codes or correction of household electrical or
plumbing (i.e. house wiring, fuses or water inlet hoses).
4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation
solutions, etc.).
5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.
6. Conversion of products from natural gas or L.P. gas.
7. Damage from accident, misuse, abuse, fire, floods, acts of God or use with products
not approved by Whirlpool.
8. Repairs to parts or systems to correct product damage or defects caused by
unauthorized service, alteration or modification of the appliance.
9. Cosmetic damage including scratches, dents, chips, and other damage to the
appliance finishes unless such damage results from defects in materials and
workmanship and is reported to Whirlpool within 30 days.
10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive
environments including but not limited to high salt concentrations, high moisture or
humidity or exposure to chemicals.
11. Food or medicine loss due to product failure.
12. Pick-up or delivery. This product is intended for in-home repair.
13. Travel or transportation expenses for service in remote locations where an authorized
Whirlpool servicer is not available.
14. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim,
decorative panels, flooring, cabinetry, islands, countertops, drywall, etc.) that
interfere with servicing, removal or replacement of the product.
15. Service or parts for appliances with original model/serial numbers removed, altered
or not easily determined.
The cost of repair or replacement under these excluded circumstances shall be
borne by the customer.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR
AS PROVIDED HEREIN. Service must be provided by a
Whirlpool designated service company. This limited
warranty is valid only in the United States or Canada
and applies only when the major appliance is used in
the country in which it was purchased. This limited
warranty is effective from the date of original consumer
purchase. Proof of original purchase date is required to
obtain service under this limited warranty.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you
specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,
you should ask Whirlpool or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation
of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and
you also may have other rights that vary from state to state or province to province.
11/14
39
Download PDF