Installation/Operation for Clothes Dryer

Installation/Operation
Clothes Dryer
Metered Commercial
Electric and Gas Models
DRY694C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 512758R2
December 2008
WARNING
FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage, personal injury or death.
W033
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do not use any phone in your building.
– Clear the room, building or area of all occupants.
– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
– If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
W052
IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be followed if the
dryer user smells gas. The gas utility instructions plus the SAFETY and WARNING note directly above
must be posted in a prominent location near the dryer for customer use.
WARNING
• Installation of unit must be performed by a qualified installer.
• Install clothes dryer according to manufacturer’s instructions and local codes.
• DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil
type) duct is installed, it must be of a specific type identified by the appliance manufacturer
as suitable for use with clothes dryers. Refer to section on connecting exhaust system.
Flexible venting materials are known to collapse, be easily crushed, and trap lint. These
conditions will obstruct clothes dryer airflow and increase the risk of fire.
W729R1
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
W053
The following information applies to the state of Massachusetts, USA.
●
This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
●
This appliance must be installed with a 36 inch (91 cm) long flexible gas connector.
●
A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.
●
This appliance must not be installed in a bedroom or bathroom.
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
1
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
3
3
3
Installation...........................................................................................
Dimensions ...........................................................................................
Before You Start ...................................................................................
Tools ................................................................................................
Additional Security...............................................................................
Installing the Dryer ...............................................................................
Step 1: Position and Level the Dryer ...............................................
Step 2: Connect Dryer Exhaust System ...........................................
Exhaust Direction.............................................................................
Exhaust System ................................................................................
Multi-Dryer Installation Exhaust Requirements ..............................
Step 3: (Gas Dryer Only) Connect Gas Supply Pipe .......................
Step 4: (Electric Dryer Only) Connect Electrical Plug ....................
Step 5: Wipe Out Inside of Dryer ....................................................
Step 6: Plug In the Dryer .................................................................
Step 7: Recheck Steps 1-6................................................................
Step 8: Check Heat Source ..............................................................
5
5
6
6
6
7
7
8
10
10
11
13
14
20
20
21
21
Operation.............................................................................................
Operation Instructions ..........................................................................
Step 1: Clean Lint Filter...................................................................
Step 2: Load Laundry.......................................................................
Step 3: Close Loading Door.............................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Insert Coin(s) or Card ..........................................................
Step 6: Start Dryer ...........................................................................
Indicator Lights ................................................................................
23
23
23
23
23
24
24
24
24
Maintenance ........................................................................................
Lubrication............................................................................................
Care of Your Dryer...............................................................................
Dryer Interior ...................................................................................
Cabinet .............................................................................................
Control Panel ...................................................................................
Exhaust System ................................................................................
Lint Filter ..............................................................................................
Motor Overload Protector.....................................................................
For Energy Conservation......................................................................
25
25
25
25
25
25
25
25
26
26
Troubleshooting .................................................................................. 27
Contact Information........................................................................... 28
Installer Checklist...............................................................
Back Cover
© Published by permission of the copyright owner
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
2
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Throughout this manual and on machine decals, you
will find precautionary statements (“DANGER,”
“WARNING,” and “CAUTION”) followed by specific
instructions. These precautions are intended for the
personal safety of the operator, user, servicer, and
those maintaining the machine.
Save These Instructions
DANGER
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
CAUTION
WARNING
To reduce the risk of fire, electric shock,
or injury to persons when using your
dryer, follow these basic precautions:
W034
1. Read all instructions before using the dryer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the dryer.
3. Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable
or explosive substances as they give off vapors
that could ignite or explode.
4. Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children. This is a safety
rule for all appliances.
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
5. Before the dryer is removed from service or
discarded, remove the door to the drying
compartment.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
6. Do not reach into the dryer if the cylinder is
revolving.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
7. Do not install or store the dryer where it will be
exposed to water and/or weather.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the dryer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
10. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
11. To reduce the risk of fire, DO NOT DRY plastics
or articles containing foam rubber or similarly
textured rubberlike materials.
12. ALWAYS clean the lint filter after every load. A
layer of lint in the filter reduces drying efficiency
and prolongs drying time.
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
3
Safety Information
13. Keep area around the exhaust opening and
adjacent surrounding area free from the
accumulation of lint, dust and dirt.
14. The interior of the dryer and the exhaust duct
should be cleaned periodically by qualified
service personnel.
15. If not installed, operated and maintained in
accordance with the manufacturer’s instructions
or if there is damage to or mishandling of this
product’s components, use of this product could
expose you to substances in the fuel or from fuel
combustion which can cause death or serious
illness and which are known to the State of
California to cause cancer, birth defects or other
reproductive harm.
16. Dryer will not operate with the loading door
open. DO NOT bypass the door safety switch by
permitting the dryer to operate with the door
open. The dryer will stop tumbling when the door
is opened. Do not use the dryer if it does not stop
tumbling when the door is opened or starts
tumbling without pressing the START
mechanism. Remove the dryer from use and call
the service person.
17. Do not put articles soiled with vegetable or
cooking oil in the dryer, as these oils may not be
removed during washing. Due to the remaining
oil, the fabric may catch on fire by itself.
18. To reduce the risk of fire, DO NOT put clothes
which have traces of any flammable substances
such as machine oil, flammable chemicals,
thinner, etc., or anything containing wax or
chemicals such as in mops and cleaning cloths, or
anything dry-cleaned at home with a drycleaning solvent in the dryer.
19. Use the dryer only for its intended purpose,
drying clothes.
20. Always disconnect the electrical power to the
dryer before attempting service. Disconnect the
power cord by grasping the plug, not the cord.
21. If supply cord is damaged, it must be replaced by
a special cord or assembly available from the
manufacturer or its service agent.
22. Install this dryer according to the
INSTALLATION INSTRUCTIONS. All
connections for electrical power, grounding and
gas supply must comply with local codes and be
made by licensed personnel when required. Do
not do it yourself unless you know how!
23. Remove laundry immediately after the dryer
stops.
24. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of reach of children at all times
(preferably in a locked cabinet).
25. Do not tumble fiberglass curtains and draperies
unless the label says it can be done. If they are
dried, wipe out the cylinder with a damp cloth to
remove particles of fiberglass.
26. ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
27. Never operate the dryer with any guards and/or
panels removed.
28. DO NOT operate the dryer with missing or
broken parts.
29. DO NOT bypass any safety devices.
30. Failure to install, maintain, and/or operate this
machine according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
IMPORTANT: Solvent vapors from dry-cleaning
machines create acids when drawn through the
heater of the drying unit. These acids are corrosive
to the dryer as well as to the laundry load being
dried. Be sure make-up air is free of solvent vapors.
IMPORTANT: Have your dryer installed properly.
Don’t do it yourself unless you know how!
NOTE: The WARNING and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the dryer.
Always contact your dealer, distributor, service agent
or the manufacturer about any problems or conditions
you do not understand.
4
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
Dimensions
8.0 in.
(20.3 cm)
23.5 in.
(59.7 cm)
28 in.
(71.1 cm)
*36.94 in. (93.83 cm)
*4.5 in.
(11.4 cm)
15.4 in.
(39.1 cm)
26.9 in.
(68.3 cm)
0.4 in.
(1.0 cm)
*15.44 in.
(39.2 cm)
*43.2 in. (109.7 cm)
2.0 in.
(5.1 cm)
*4.0 in.
(10.2 cm)
DRY2128N
ELECTRIC MODELS
DRY2128N
*With leveling legs turned into base.
8.0 in.
(20.3 cm)
23.5 in.
(59.7 cm)
28 in.
(71.1 cm)
*4.0 in.
(10.2 cm)
15.4 in.
(39.1 cm)
0.4 in.
(1.02 cm)
26.9 in.
(68.3 cm)
*36.94 in. (93.83 cm)
*15.44 in.
(39.2 cm)
2.3 in. (6 cm)
*43.2 in. (109.7 cm)
*4.5 in.
(11.4 cm)
2.0 in.
(5.1 cm)
2.8 in.
(7 cm)
DRY2250N
1
GAS MODELS
DRY2250N
*With leveling legs turned into base.
1
3/8 in. NPT Gas Connection
NOTE: Side, rear and bottom exhaust openings are
4 inches (10.2 cm) ducting. Gas models cannot be
vented out left side of cabinet because of burner
housing.
512758
IMPORTANT: The dryer should have sufficient
clearance around it for needed ventilation and for
the ease of installation and servicing. For maximum
drying performance, we recommend that more
clearance be allowed around the dryer than the
clearances that are listed throughout this manual.
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
5
Installation
Before You Start
WARNING
Tools
For most installations, the basic tools you will need
are:
Any disassembly requiring the use of
tools must be performed by a suitably
qualified service person.
W299
2
1
Additional Security
3
Torx security screws are available (as optional
equipment at extra cost) for securing lower access
panel to dryer base. Order part number 62853.
A Torx bit, part number 282P4, is available (as
optional equipment at extra cost) for installing the
Torx security screws.
A Torx bit holder, part number 24161, is available (as
optional equipment at extra cost) to be used with the
Torx bit.
4
5
D818I
1
2
3
4
5
Wrench
Screwdrivers
Level
Teflon Tape
Duct Tape
Figure 1
NOTE: An 8 in. (20.32 cm) coin drawer is required
for coin operated models.
6
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
Installing the Dryer
No other fuel burning appliance should be installed in
the same closet with the dryer.
Step 1: Position and Level the Dryer
The dryer must not be installed or stored in an area
where it will be exposed to water and/or weather.
Install dryer before washer. This allows room for
attaching exhaust duct.
Install the four rubber feet (in accessories bag).
Select a location with a solid floor. Dryers installed in
residential garages must be elevated 18 inches (46 cm)
above the floor.
The dryer needs sufficient clearance and an adequate
air supply for proper operation and ventilation, and for
easier installation and servicing. (Minimum clearances
are shown in Figure 2).
B
E
D
A
A
C
A
1 DRY2180N
SIDE VIEW
FRONT VIEW
(w/o Closet Door)
Area
*42 in.
(107 cm)
Description
Free Standing/Alcove Installation
A
Dryer sides and rear clearance
0 in. (0 cm)
B
Dryer top clearance
12 in. (30.5 cm)
C
Dryer front clearance
Not Applicable
D
Exhaust duct clearance to combustible material
2 in. (5.1 cm)
E
Weather hood to ground clearance
12 in. (30.5 cm)
(Minimum clearances are shown.)
DRY2180N
* NOTE: For new installations, locate top of wall vent 42 inches (107 cm) above floor to make venting easier
to connect.
1
Outer wall of enclosure
Figure 2
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
7
Installation
Place the dryer in position, and adjust the legs until the
dryer is level from side to side and front to back.
Leveling legs can be adjusted from inside the dryer
with a 1/4 in. driver. All four legs must rest firmly on
the floor so the weight of the dryer is evenly
distributed. The dryer must not rock.
Step 2: Connect Dryer Exhaust System
WARNING
To reduce the risk of fire and combustion
gas accumulation the dryer MUST be
exhausted to the outdoors.
W604
2
To reduce the risk of fire and the
accumulation of combustion gases, DO NOT
exhaust dryer air into a window well, gas
vent, chimney or enclosed, unventilated
area, such as an attic, wall, ceiling, crawl
space under a building or concealed space
of a building.
1
W045
WARNING
3
4
DRY213
DRY2131N
1
2
3
4
Dryer Base
Level
Leveling Leg
Rubber Foot
Figure 3
This gas appliance contains or produces a
chemical or chemicals which can cause
death or serious illness and which are
known to the State of California to cause
cancer, birth defects, or other reproductive
harm. To reduce the risk from substances in
the fuel or from fuel combustion, make sure
this appliance is installed, operated, and
maintained according to the instructions in
this manual.
W115
IMPORTANT: In mobile home installations, gas
dryers MUST be permanently attached to the floor
at the time of installation. Order No. 526P3 Hold
Down Kit (available at extra cost) for a
manufactured (mobile) home installation. Follow
the instructions supplied with the kit.
Installation of unit must conform to the Manufactured
Home Construction and Safety Standards, Title 24
CF4, Part 32-80 or Standard CAN/CSA-Z240 MH.
To reduce the risk of fire, DO NOT use
plastic or thin foil ducting to exhaust the
dryer.
W354
To reduce the risk of fire, the exhaust duct
and weather hood MUST be fabricated of a
material that will not support combustion.
Rigid or flexible metal pipe is recommended
for a clothes dryer.
W048
WARNING
To reduce the risk of fire due to increased
static pressure, we do not recommend
installation of in-line secondary lint filters or
lint collectors. If secondary systems are
mandated, frequently clean the system to
assure safe operation.
W749
8
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
IMPORTANT: Installing in-line filters or lint
collectors will cause increased static pressure.
Failure to maintain the secondary lint system will
decrease dryer efficiency and may void machine
warranty.
●
DO NOT use plastic or thin foil ducting. Rigid
metal duct is recommended.
●
Dryer exhaust duct MUST NOT terminate under
mobile home.
●
Dryer exhausts 220 cfm (measured at back of
dryer).
●
DO NOT install flexible duct in concealed
spaces, such as a wall or ceiling.
●
Static pressure in exhaust duct should not be
greater than .6 inches water column (1.5 cm),
measured with manometer placed on exhaust
duct two feet (61 cm) from dryer (check with
dryer running and no load). In multi-dryer
installations, all dryers connected to the main
collector duct should be operating when pressure
is checked.
●
Exhausting dryer in hard-to-reach locations can
be done by installing 521P3 Flexible Metal Vent
Kit (available as optional equipment at extra
cost).
●
Sufficient make-up air must be supplied to
replace the air exhausted by the dryer. The free
area of any opening for outside air must be at
least 40 in2 (260 cm2).
●
Energy efficient buildings with low air
infiltration rates should be equipped with an air
exchanger that can accommodate on demand
make-up air needs in the laundry room. These
devices can be obtained through your building
contractor or building material suppliers.
●
Do not draw make-up air from a room containing
a gas fired water heater, a dry cleaner or a hair
salon.
●
Failure to exhaust dryer properly will void
warranty.
D740I
DO
DON’T
D740I
Figure 4
●
Locate dryer so exhaust duct is as short as
possible.
●
Be certain old ducts are cleaned before installing
your new dryer.
●
Use 4 inch (102 mm) diameter rigid or flexible
metal duct.
●
The male end of each section of duct must point
away from the dryer.
●
Use as few elbows as possible.
●
Use duct tape or pop-rivets on all duct joints. DO
NOT use sheet metal screws or fasteners on
exhaust pipe joints which extend into the duct
and catch lint.
●
Ductwork that runs through unheated areas must
be insulated to help reduce condensation and lint
build-up on pipe walls.
●
Install backdraft dampers in multi-dryer
installations.
●
In mobile home installations, dryer exhaust duct
must be secured to mobile home structure.
512758
NOTE: Venting materials are not supplied with the
dryer (obtain locally).
IMPORTANT: DO NOT block the airflow at the
bottom of the dryer’s front panel with laundry,
rugs, etc. Blockage will decrease airflow through
the dryer, thus reducing the efficiency of the dryer.
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
9
Installation
Exhaust Direction
Exhaust System
The dryer can be exhausted to the outdoors through the
back, left, right or bottom of the dryer. EXCEPTION:
Gas dryers cannot be vented out the left side
because of the burner housing.
For best drying results, recommended maximum
length of exhaust system is shown in Table 1.
To prevent backdraft when dryer is not in operation,
outer end of exhaust pipe must have a weather hood
with hinged dampers (obtain locally).
Dryer is shipped from factory ready for rear exhaust.
Exhausting the dryer through sides or bottom can be
accomplished by installing a Directional Exhaust Kit,
528P3, available as optional equipment at extra cost.
Number of
90° Elbows
NOTE: Weather hood should be installed at least
12 inches (30.5 cm) above the ground. Larger
clearances may be necessary for installations where
heavy snowfall can occur.
Weather Hood Type
Use Only for Short Run installations
Recommended
4 in.
(10.2 cm)
4 in.
(10.2 cm)
D673I
0
1
2
3
4
2-1/2 in.
(6.35 cm)
D802I
Maximum length of 4 in. (10.2 cm) diameter rigid metal duct.
65 feet (19.8 m)
55 feet (16.8 m)
55 feet (16.8 m)
47 feet (14.3 m)
36 feet (11.0 m)
28 feet (8.5 m)
47 feet (14.3 m)
41 feet (12.5 m)
30 feet (9.1 m)
22 feet (6.7 m)
NOTE: Deduct 6 feet (1.8 m) for each additional elbow.
Table 1
NOTE: The maximum length of a 4 in. (10.2 cm)
diameter flexible metal duct must not exceed
7.87 ft. (2.4 m), as required to meet UL2158, clause
7.3.2A.
10
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
Multi-Dryer Installation Exhaust
Requirements
Figure 5 shows a typical example of a multiple dryer
installation. Note how each dryer has its own exhaust
system vented to the central exhaust duct.
1
2
24 in. (61 cm)
MINIMUM CLEARANCE
TO ROOF/GROUND
3
METERED MODELS
ILLUSTRATED
DRY2130N
DRY2130N
1
2
58786 Backdraft Damper (Available through
your local authorized parts source)
Clean Out Cover (Must be provided). Inspect
monthly.
3
Weather Hood or Sweep Elbow
(No cap or screen)
Figure 5
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
11
Installation
1
A
B
C
D
E
F
G
H
I
J
2
K
5
3
AIR
FLOW
4
EXHAUST AIR FLOW
MAXIMUM LENGTH OF DUCT
30 feet (9.1 m)
30°
EXHAUST
OUTLET
24 in. (61 cm)
MINIMUM
CLEARANCE TO
ROOF/GROUND
D686I
HORIZONTAL EXHAUST INSTALLATION
D686I
1
2
NOTE: Where the exhaust duct pierces a
combustible wall or ceiling, the opening must be
sized per local codes.
Wall
3
4
5
2 in. (5 cm) Minimum or Clearance per Local
Codes
No Screen or Cap
Clean Out Cover – Inspect Monthly
Figure 6
WARNING
2
To reduce the risk of fire and the
accumulation of combustion gases, DO NOT
exhaust dryer air into a window well, gas
vent, chimney or enclosed, unventilated
area, such as an attic, wall, ceiling, crawl
space under a building or concealed space
of a building.
3
24 in. (61 cm)
MINIMUM
CLEARANCE TO
ROOF/GROUND
1
W045
CONNECT TO DRYER
5
4
VERTICAL EXHAUST INSTALLATION
D753I
1
2
3
4
5
Roof
No Screen or Cap
Wall
2 in. (5 cm) Minimum
NOTE: Where the exhaust duct pierces a
combustible wall or ceiling, an opening must
be sized as shown or per local codes.
Figure 7
12
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
Duct Station
Minimum Diameter of
Collector Duct
A
4 inches (10.2 cm)
B
8 inches (20.3 cm)
C
9 inches (22.9 cm)
D
10 inches (25.4 cm)
E
11 inches (27.9 cm)
F
12 inches (30.5 cm)
G
13 inches (32.6 cm)
H
14 inches (35.6 cm)
I
15 inches (38.1 cm)
J
15 inches (38.1 cm)
K
16 inches (40.6 cm)
1. Make certain your dryer is equipped for use with
the type of gas in your laundry room. Dryer is
equipped at the factory for Natural Gas with a
3/8 inch NPT gas connection.
NOTE: The gas service to a gas dryer must
conform with the local codes and ordinances, or in
the absence of local codes and ordinances, with the
latest edition of the National Fuel Gas Code ANSI
Z223.1/NFPA 54 or the CAN/CSA-B149.1 Natural
Gas and Propane Installation Code.
Natural Gas, 1000 Btu/ft3 (37.3 MJ/m3) service must
be supplied at minimum 5.0 inch water column
pressure to maximum 10.5 inch water column
pressure.
A Backdraft Damper, Part No. 58786 (obtain locally),
should be installed in a 4 inch (10.2 cm) diameter
VERTICAL duct system. This will prevent a backdraft
when dryer is not in use, and will keep the exhaust air
in balance within the central exhaust system.
For proper operation at altitudes above 2000 feet
(610 m) the natural gas valve spud orifice size must be
reduced to ensure complete combustion. Refer to
Table 2.
Natural Gas Altitude Adjustments
Altitude
Step 3: (Gas Dryer Only) Connect Gas
Supply Pipe
WARNING
To reduce the risk of gas leaks, fire or
explosion:
• The dryer must be connected to the type
of gas as shown on nameplate located in
the door recess.
• Use a new flexible stainless steel
connector.
• Use pipe joint compound insoluble in L.P.
(Liquefied Petroleum) Gas, or Teflon tape,
on all pipe threads.
• Purge air and sediment from gas supply
line before connecting it to the dryer.
Before tightening the connection, purge
remaining air from gas line to dryer until
odor of gas is detected. This step is
required to prevent gas valve
contamination.
• Do not use an open flame to check for gas
leaks. Use a non-corrosive leak detection
fluid.
• Any disassembly requiring the use of
tools must be performed by a suitably
qualified service person.
Orifice Size
feet
m
#
inches
mm
Part
Number
2,000
610
41
0.0960
2.44
503776
3,000
915
42
0.0935
2.37
503777
5,500
1,680
43
0.0890
2.26
503778
7,000
2,135
44
0.0860
2.18
58719
9,000
2,745
45
0.0820
2.08
503779
10,500
3,200
46
0.0810
2.06
503780
Table 2
2. Remove the shipping cap from the gas
connection at the rear of the dryer. Make sure you
do not damage the pipe threads when removing
the cap.
3. Connect to gas supply pipe.
W316
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
13
Installation
NOTE: When connecting to a gas line, an
equipment shut-off valve must be installed within
6 feet (1.8 m) of the dryer. An 1/8 in. NPT pipe plug
must be installed as shown for checking inlet
pressure. Refer to Figure 8.
2
3
Step 4: (Electric Dryer Only) Connect
Electrical Plug
Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz,
3 or 4 wire electrical supply. Refer to serial plate for
specific electrical requirements.
4
D233I
D233I
5
503785
58755
503786
NOTE: DO NOT connect the dryer to L.P. Gas
Service without converting the gas valve. Install
L.P. Gas Conversion Kit 458P3, available at extra
cost.
5
2
3
4
Part No.
Table 3
1
1
L.P. Altitude Adjustments
Altitude
Orifice Size
feet
m
No.
inches
mm
3500
1070
54
0.0550
1.40
7500
2290
55
0.0520
1.32
11000
3355
56
0.0465
1.18
New Stainless Steel Flexible Connector –
(Use design CSA certified connector)
Use only if allowed by local codes
1/8 in. NPT Pipe Plug
Equipment Shut Off Valve
Black Iron Pipe
Shorter than 20 ft. (6.1 m) – Use 3/8 in.
(9.5 mm) pipe.
Longer than 20 ft. (6.1 m) – Use 1/2 in.
(12.7 mm) pipe.
3/8 in. NPT Gas Connection
Figure 8
4. Tighten all connections securely. Turn on gas and
check all pipe connections (internal & external)
for gas leaks with a non-corrosive leak detection
fluid.
NOTE: The wiring diagram is located inside the
control hood.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local
regulations as might apply. It is the
customer’s responsibility to have the wiring
and fuses installed by a qualified electrician
to make sure adequate electrical power is
available to the dryer.
W521
NOTE: The dryer and its appliance main gas valve
must be disconnected from the gas supply piping
system during any pressure testing of that system
at test pressures in excess of 1/2 psi (3.45 kPa).
Refer to Step 8 (Check Heat Source).
L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft3
(93.1 MJ/m3) service must be supplied at 10 ± 1.5 inch
water column pressure.
For proper operation at altitudes above 3500 feet
(1070 m) the L.P. gas valve spud orifice size must be
reduced to ensure complete combustion. Refer to
Table 3.
14
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
Grounding Information
●
●
This dryer must be connected to a grounded
metal, permanent wiring system; or an
equipment-grounding conductor must be run
with the circuit conductors and connected to the
equipment-grounding terminal or lead on the
dryer.
The dryer has its own terminal block that must be
connected to a separate branch, 60 Hertz, single
phase circuit, AC (alternating current) circuit,
fused at 30 Amperes (the circuit must be fused
on both sides of the line). Electrical service for
the dryer should be of maximum rated voltage
(208 or 240 Volt, depending on heating
element) listed on the nameplate. Do not
connect dryer to 110, 115, or 120 Volt circuit.
512758
●
Heating elements are available for field
installation in dryers which are to be connected to
electrical service of different voltage than that
listed on nameplate, such as 208 Volt.
NOTE: Branch circuit wire size requirements to
laundry room outlet are shown in Table 4.
Wire Length
Dryer
Less than
15 ft. (4.5 m)
Longer than
15 ft. (4.5 m)
Listed No. 10 AWG
Copper wire only
Listed No. 8 AWG
Copper wire only
Table 4
●
The power cord connection between wall
receptacle and dryer terminal block IS NOT
supplied with dryer. Type of power cord and
gauge of wire must conform to local codes.
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
15
Installation
IMPORTANT: Use only a new U.L. listed No. 10
(copper wire only) three conductor power supply
cord kit rated 240 Volts (minimum) 30 Amperes
and labeled as suitable for use in a clothes dryer.
1
1
2
3
8
7
2
4
3
5
4
6
THREE-WIRE
D679I
THREE-WIRE CONNECTION
D275I
D679I
2
8
1
1
3
3
7
4
1
4
FOUR-WIRE
9
D006I
1
2
3
4
Typical Receptacle
Power Cord
Strain Relief Nut
Strain Relief
10
11
6
FOUR-WIRE CONNECTION
Figure 9
D680I
D680I
NOTE: Dryer is shown with access cover removed for
illustration purposes only. NEVER operate the dryer
with access cover removed.
1
Ground Wire
2
Ground to Neutral Wire
3
Neutral Terminal
4
“L2” Terminal
5
Center Wire (Neutral)
6
Strain Relief (Not supplied with dryer)
7
Ground Screw
8
“L1” Terminal
9
Black Wire
10
White Wire (Neutral)
11
Red Wire
Figure 10
16
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
Connecting Power Cord with Three-Wire Plug
NOTE: Four-wire cord is required for mobile
homes or where codes do not permit grounding
through neutral.
NOTE: The power cord is NOT supplied with the
electric dryer. Type of power cord and gauge of wire
must conform to local codes and instructions.
POWER SUPPLY
POWER SUPPLY
1
The method of wiring the dryer is optional and subject
to local code requirements.
2
NOTE: Connect the dryer to the power supply with the
MAXIMUM RATED VOLTAGE listed on the nameplate.
A typical
30-Amp
Three-Wire
Receptacle
NEMA Type
10-30R
3
INTERMEDIATE
FUSE BOX (may
be omitted if
service entrance
box is fused)
4
WALL
RECEPTACLE
120 ± 12
V.A.C.
5
120 ± 12
V.A.C.
240 ± 12
V.A.C.
NOTE: Use COPPER WIRE only.
Shorter than 15 ft. (4.5 m) – use 10 AWG
Longer than 15 ft. (4.5 m) – use 8 AWG
INTERMEDIATE
SHUT-OFF BOX
(may or may not
be fused)
6
7
L1
L2
L1
POWER CORD CONNECTION
L2
DIRECT CONNECTION
D816I
1
3 Wire Grounded Neutral 120/240 Volt, 60 Hertz
AC 1 Phase Service Entrance Switch Box
(Refer to NOTE above)
2
3
30 Ampere Fuses or Circuit Breaker
Neutral Wire
4
5
6
7
Metallic or Non-Metallic Sheathed Cable
(Copper Wire Only)
Power Cord (Not supplied with dryer)
Neutral
Terminal Block in Dryer
Figure 11
1. Disconnect power to dryer.
3. Use a strain relief and insert end of power cord
through power supply hole.
2. Remove access cover from rear of dryer.
D696I
D695I
Figure 12
512758
Figure 13
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
17
Installation
4. Use the three screws from the accessories bag to
attach the power cord wires to the terminal block.
Refer to Figure 14.
1
Connecting Power Cord with Four-Wire Plug
NOTE: Four-wire cord is required for mobile
homes or where codes do not permit grounding
through neutral.
2
2
1
3
4
12
V. 0 ±
A 1
.C 2
.
3
12
V. 0 ±
A 1
.C 2
.
D286I
240 ± 12
V.A.C.
“L1” Terminal
Neutral Terminal
“L2” Terminal
12
V. 0 ±
A 1
.C 2
.
0
V.A.C.
12
V. 0 ±
A 1
.C 2
.
1
2
3
Figure 14
5. Tighten all screws firmly.
IMPORTANT: Failure to tighten these screws
firmly may result in wire failure at the terminal
block.
6. Secure the strain relief to the power cord, or
wires, where they enter the dryer cabinet.
7. Check the continuity of the ground connection
before plugging the cord into an outlet. Use an
acceptable indicating device connected to the
center grounding pin of the plug and the green
screw on the back of the cabinet.
DRY2016N
1
2
3
4
Typical Four-Wire Receptacle
Power Cord – Not Supplied with Dryer
Strain Relief Nut
Strain Relief
Figure 15
1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
8. Reinstall access cover and screw.
D695I
Figure 16
18
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
3. Remove ground screw and save for use in Step 5.
Remove wire and use in Step 6.
5. Attach power cord ground (green) wire to rear
bulkhead using ground screw removed in Step 3.
1
1
7
6
5
D697I
2
4
D697I
1
Ground Screw
3
DRY1920N
DRY1920N
Figure 17
4. Use a strain relief and insert end of power cord
through power supply hole.
1
2
3
4
5
6
7
White
“L2” Terminal
Black
Green
Red
Neutral Terminal
“L1” Terminal
Figure 19
6. Use the three screws from the accessories bag to
attach the remaining power cord wires to the
terminal block as follows:
a. Red wire to “L1” terminal.
D696I
Figure 18
b. Black wire to “L2” terminal.
c. White wire to Neutral terminal.
NOTE: When installing the white wire, loop the
free eyelet end of the ground wire (removed in
Step 3) and attach along with the white wire to the
neutral (center) terminal on the terminal block.
7. Tighten all screws firmly.
IMPORTANT: Failure to tighten these screws
firmly may result in wire failure at the terminal
block.
8. Secure the strain relief to the power cord, or
wires, where they enter the dryer cabinet.
9. Check the continuity of the ground connection
before plugging the cord into an outlet. Use an
acceptable indicating device connected to the
center grounding pin of the plug and the green
screw on the back of the cabinet.
10. Reinstall access cover and screw.
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
19
Installation
Step 5: Wipe Out Inside of Dryer
Before using dryer for the first time, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside dryer drum.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1, and such local
regulations as might apply. It is the
customer’s responsibility to have the wiring
and fuses installed by a qualified electrician
to make sure adequate electrical power is
available to the dryer.
W521
When plugging in the dryer:
DRY2133N
DRY2133N
Figure 20
Step 6: Plug In the Dryer
Electric Dryer
Connect the dryer to an electrical power source. Refer
to Step 4 for information on connecting power cord.
●
Do not overload circuits.
●
Do not use an adapter.
●
Do not use an extension cord.
●
Do not operate both a washer and gas dryer on
the same circuit. Use separately fused 15 Amp
circuits.
The dryer is designed to be operated on a separate
branch, polarized, three-wire, effectively grounded,
120 Volt, 60 Hertz, AC (alternating current) circuit
protected by a 15 Ampere fuse, equivalent fusetron or
circuit breaker.
The three-prong grounding plug on the power cord
should be plugged directly into a polarized three-slot
effectively grounded receptacle rated 120 Volts AC
(alternating current) 15 Amps. Refer to Figure 22 to
determine correct polarity of the wall receptacle.
Grounding Information
Connect to 30 Amp circuit.
D275I
Figure 21
Gas Dryer
Dryer requires 120 Volt, 60 Hertz electrical supply and
comes equipped with a 3-prong grounding plug. Refer
to serial plate for specific electrical requirements.
The dryer must be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. The dryer is equipped
with a cord having an equipment-grounding conductor
and a 3 prong grounding plug. The three-prong
grounding plug on the power cord should be plugged
directly into a polarized three-slot effectively
grounded receptacle rated 110/120 Volts AC
(alternating current) 15 Amps.
NOTE: The wiring diagram is located inside the
control hood.
20
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installation
WARNING
WARNING
This dryer is equipped with a three-prong
(grounding) plug for your protection against
shock hazard and should be plugged
directly into a properly grounded threeprong receptacle. Do not cut or remove the
grounding prong from this plug.
To reduce the risk of an electric shock or
fire, DO NOT use an extension cord or an
adapter to connect the dryer to the electrical
power source.
W037
M
W036
WARNING
2
3
1
Improper connection of the equipmentgrounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the dryer is properly
grounded.
120±12
V.A.C
0 V.A.C
D254I
120±12
V.A.C
W038
Do not modify the plug provided with the dryer – if it
will not fit the outlet, have a proper outlet installed by
a qualified electrician.
4
NOTE: Have a qualified electrician check the
polarity of the wall receptacle. If a voltage reading
is measured other than that illustrated, the
qualified electrician should correct the problem.
Do not operate other appliances on the same circuit
when this appliance is operating.
5
Plug cord into separately fused 15 Amp circuit.
DRY2
DRY2022N
1
2
3
4
5
“L1”
Ground
Neutral
Neutral SIde
Round Grounding Prong
Figure 22
Step 7: Recheck Steps 1-6
Refer to Installer Checklist on the back cover of this
manual and make sure that dryer is installed correctly.
Step 8: Check Heat Source
Electric Dryers
Close the loading door and start the dryer in a heat
setting (refer to the Operation section). After the dryer
has operated for three minutes, the exhaust air or
exhaust pipe should be warm.
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
21
Installation
Gas Dryers
After the dryer has operated for approximately five
minutes, observe burner flame through lower front
panel. Adjust the air shutter to obtain a soft, uniform
blue flame. (A lazy, yellow-tipped flame indicates lack
of air. A harsh, roaring, very blue flame indicates too
much air.) Adjust the air shutter as follows:
IMPORTANT: This operation is to be conducted
by qualified personnel only.
To view the burner flame, remove the lower front
panel of the dryer.
Close the loading door, start the dryer in a heat setting
(refer to the Operation section). The dryer will start,
the igniter will glow red and the main burner will
ignite.
IMPORTANT: If all air is not purged out of gas
line, gas igniter may go off before gas is ignited. If
this happens, after approximately two minutes
igniter will again attempt gas ignition.
1. Loosen the air shutter lockscrew.
2. Turn the air shutter to the left to get a luminous
yellow-tipped flame, then turn it back slowly to
the right to obtain a steady, soft blue flame.
3. After the air shutter is adjusted for proper flame,
tighten the air shutter lockscrew securely.
4. Reinstall the lower front panel.
WARNING
IMPORTANT: If igniter does not light, make sure
gas is turned on.
For personal safety, lower front panel must
be in place during normal operation.
W046
After the dryer has operated for approximately three
minutes, exhaust air or exhaust pipe should be warm.
MODELS THROUGH SERIAL NO. 0803
MODELS STARTING SERIAL NO. 0804
2
2
1
1
6
6
3
3
4
5
4
5
D700I
1
2
3
4
Closed Position
Shut-Off Valve Handle
Air Shutter Lockscrew
Air Shutter
DRY2235N
5
6
1/8 in. (3.1 mm) Pipe Plug
(For checking manifold pressure)
Open Position
Figure 23
22
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Operation
Operation Instructions
Step 2: Load Laundry
Load clothes loosely into dryer drum. Add fabric
softener sheet if desired.
WARNING
To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS before operating
this appliance.
IMPORTANT: To avoid damage to dryer, do not
use more than one fabric softener sheet per load.
W727
IMPORTANT: Before using dryer for the first time,
use an all-purpose cleaner, or a detergent and
water solution, and a damp cloth to remove
shipping dust from inside of dryer drum.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
Step 1: Clean Lint Filter
DRY2169NDRY2169N
Clean lint filter before each use.
Figure 25
Step 3: Close Loading Door
Close loading door. Dryer will not operate with the
door open.
DRY2168N
DRY2168N
Figure 24
DRY2170N
DRY2170N
Figure 26
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
23
Operation
Step 4: Set Fabric Selector
Step 6: Start Dryer
Select HIGH TEMP, MED TEMP, LOW TEMP or
DELICATES by pushing touchpad.
To start dryer, push START pad.
NOTE: Always follow manufacturer’s care label
instructions.
To stop dryer at any time, open the door. To restart the
dryer, close door and push START pad.
Cycle is completed when time remaining reaches
00 minutes.
DRY2171N
DRY2172N
DRY2172N
DRY2171N
Figure 29
Figure 27
Step 5: Insert Coin(s) or Card
Remove knits when slightly damp because overdrying
may cause shrinkage. Do not tumble dry knit woolens.
If Additional Time Feature is turned on, additional
dryer time may be purchased at cycle start or while
dryer is running.
Indicator Lights
To Insert Money
Insert coin(s) in coin slot. Check pricing as seen on
digital display.
START
START is lit whenever the dryer is not in a cycle, the
full vend price has been satisfied and the dryer door is
closed. When the START pad is pressed, the cycle will
begin or resume.
DRYING
DRYING is lit to indicate that one of the heated cycles
(HIGH TEMP, MED TEMP, LOW TEMP or
DELICATES) is currently in operation. DRYING will
turn off at the end of a heated cycle or when the COOL
DOWN cycle begins.
COOL DOWN
DRY2173N
COOL DOWN is lit whenever the COOL DOWN
portion of a heated cycle is active. It is also lit when no
heat is programmed for a cycle in operation.
Figure 28
To Insert Card
Insert card into opening.
24
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Maintenance
Lubrication
Exhaust System
All moving parts are sealed in a permanent supply of
lubricant or are equipped with oilless bearings.
Additional lubrication will not be necessary.
WARNING
To reduce the risk of electric shock,
disconnect the electrical service to the
dryer before cleaning.
Care of Your Dryer
WARNING
W043
To reduce the risk of an electric shock,
serious injury or death, disconnect the
electrical service to the dryer before
cleaning the interior.
W132
Dryer Interior
Wipe the surfaces using a soft cloth and household
cleaner or a non-abrasive paste of powdered laundry
detergent and hot water, followed by a short heat cycle
with a load of rags.
To remove crayon or ball point ink off the dryer drum,
put the heat on high and use old rags in the dryer to
absorb the crayon or ink. If unsuccessful, contact the
appliance dealer. DO NOT use any chemicals in the
dryer.
IMPORTANT: The use of chlorine bleach for
removing any discolorations should be avoided
because bleach could damage the finish.
Cabinet
Wipe the dryer cabinet as needed. If detergent, bleach
or other washing products have been spilled on the
dryer, wipe immediately. Some products will cause
permanent damage if spilled on the cabinet.
Control Panel
The exhaust duct should be inspected after one year of
use and cleaned if necessary by a qualified service
person to remove any lint build-up. Inspect and clean
exhaust duct every one to two years as required
thereafter.
The weather hood should be checked frequently to
make sure the dampers move freely, dampers are not
pushed in and that nothing has been set against them.
Keep dryer area clear and free from combustible
materials, gasoline and other flammable vapors and
liquids.
Do not obstruct the flow of combustion and ventilation
air.
NOTE: Verify proper operation after servicing.
Lint Filter
CLEAN THE LINT FILTER BEFORE DRYING
EACH LOAD. (Refer to Figure 30 for lint filter
location.) Cleaning the lint filter is important because
a layer or pad of lint on the filter will block the flow of
air through the dryer, thus reducing the efficiency of
the dryer. The clothes will take longer to dry and
energy will be wasted.
The lint filter may be washed if needed. Annually
remove lint filter and screw to vacuum the duct under
it.
Use only a damp or sudsy cloth for cleaning the
control panel. Some spray pretreat products may harm
the finish on the control panel.
NOTE: The wiring diagram is located inside the
control panel.
1
WARNING
Label all wires prior to disconnection
when servicing controls. Wiring errors
can cause improper and dangerous
operation.
W049
512758
DRY2168N
1
DRY2168N
Lint Filter
Figure 30
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
25
Maintenance
Motor Overload Protector
The dryer’s motor overload protector stops the motor
automatically in the event of an overload. After
cooling, the overload protector will reset itself. Dryer
can be restarted by pressing the START pad. If
overload protector cycles again, remove the dryer from
use and call the service person to correct the problem.
26
For Energy Conservation
●
Make sure the lint filter is always clean.
●
Do not overload dryer.
●
Do not overdry clothes.
●
Remove items to be ironed while still damp.
●
Large loads of similar fabrics dry the most
efficiently. However, dry permanent press in
smaller loads to prevent wrinkling.
●
Use the correct temperature FABRIC
SELECTOR setting for the type of fabric being
dried.
●
Locate your dryer so the exhaust duct is as short
and straight as possible.
●
Do not open the door during the drying cycle.
●
Plan to do your laundry on low humidity days;
your clothes will dry faster.
●
Should you plan to dry several loads, do them
one after another, then you do not have to reheat
the dryer unit’s interior parts each time.
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Troubleshooting
Try these troubleshooting tips before making a service
call – You may save time and money!
Dryer Symptom
Possible Cause/Solution
•
•
Dryer won’t start
•
•
•
•
•
Dryer won’t heat
•
•
•
•
Dryer doesn’t dry clothes
satisfactorily
•
•
•
•
•
•
Dryer is noisy
•
•
Insert coin(s) or card.
For dryers equipped with a power cord, make sure the power cord is plugged all
the way into the electrical outlet.
Make sure loading door is closed.
Press START pad.
Make sure the laundry room fuse(s) isn’t blown or loose, or circuit breakers
aren’t open. The dryer itself does not have an electrical fuse. An electric dryer
has an electrical circuit with two fuses.
Check if motor overload protector has cycled. Wait 10 minutes and try again.
Make sure the laundry room fuse(s) isn’t blown or loose, or circuit breakers
aren’t open. The dryer itself does not have an electrical fuse. An electric dryer
has an electrical circuit with two fuses.
Make sure controls are in a HEAT setting.
Gas dryer only – Make sure equipment and main gas line valve is turned on.
Check exhaust duct to outside to see if it is kinked, blocked or needs cleaning.
Check weather hood to make sure flapper moves freely, has not been pushed in
or has not been blocked.
Check exhaust duct to outside to see if it is kinked, blocked or needs cleaning.
Check weather hood to make sure flapper moves freely, has not been pushed in
or has not been blocked.
Clean the lint filter.
Make sure the load isn’t too small. Small loads may not tumble properly or dry
evenly.
Check load being dried. Heavy items dried with lightweight items will not dry as
quickly as the rest of the load.
Check dryer for foreign objects (nails, coins, bobby pins, metal, plastic toys,
etc.). Remove items from dryer.
Make sure dryer is level. Uneven leveling can cause vibration.
Normal operating sounds include the tick of timer advancing, heat source going
on and off, and humming of air moving through the dryer and exhaust system.
Clothes are too wrinkled
•
•
Check heat setting. Overdrying can cause wrinkling.
Check load size. Large loads may not tumble properly and may cause wrinkling.
Clothes have odor
•
Check room for odors before drying clothes. Any odor (fried foods, paint,
varnish, cleaners, burning wood, etc.) will transfer to clothing as the dryer draws
air from the room. Ventilate room before drying clothes.
512758
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
27
Contact Information
If service is required, contact the nearest Factory
Authorized Service Center.
WARNING
If you are unable to locate an authorized service center
or are unsatisfied with the service performed on your
dryer, contact the source from which you purchased
your dryer.
Date Purchased___________________________
Model Number____________________________
Serial Number____________________________
When calling or writing about your dryer, PLEASE
GIVE THE MODEL AND SERIAL NUMBERS. The
model and serial numbers are located on the
nameplate. The nameplate will be in the location
shown in the illustration below. Please include a copy
of your bill of sale and any service receipts you have.
To reduce the risk of serious injury or
death, DO NOT repair or replace any part
of the dryer or attempt any servicing
unless specifically recommended in the
user-maintenance instructions or in
published user-repair instructions that
you understand and have the skills to
carry out.
W133
If replacement parts are required, contact the source
from which you purchased your dryer.
1
D063K
1
Nameplate
Figure 31
28
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
512758
Installer Checklist
Fast Track for Installing the Dryer
(Refer to the manual for more detailed information)
1
5
• Position and Level the Dryer.
• Wipe Out Inside
of Dryer.
LEVEL
D255I
D255I
D256I
CHECK
2
CHECK
D259I
6
• Connect Dryer
Exhaust System.
DRY2133N
DRY2133N
• Plug In
the Dryer.
Gas
D275I
D740I
Electric
D740I
CHECK
CHECK
3
GAS ONLY
• Connect Gas
Supply Pipe.
• Check for Gas
Leaks.
7
CHECK
8
CHECK
4
D258I
• Check Heat Source.
CHECK
ELECTRIC ONLY
• Connect
Electrical Cord.
CHECK
• Recheck Steps 1-6.
W315IE0A
D699I
D254I
D254I
Download PDF