Congratulations on your new Scan wood-burning

A S S E M B LY- A N D I N S T R U C T I O N S M A N U A L
Scan 64 - series
Congratulations on your new Scan wood-burning stove
You have purchased a product by one of Europe’s leading manufacturer’s of wood-burning stoves, and we are sure that you will have years of pleasure with your purchase. To make the best possible use of your stove, it is important that you follow our advice and instructions.
Please read this Assembly- and instructions manual before you start to assemble your stove.
Product registration number
Please indicate the product registration number at any enquiry
S C A N A / S - D K- 5 4 9 2 V I S S E N B J E R G
2
CONTENTS
Table of contents
Technical data ......................................................................................................... 3
Installation
Safety
Technical data and dimensions
Dimension sketch
Type plate
Product registration number
Additional accessories
Service box
Loose parts
Assembly .................................................................................................................. 8
Remove packaging
Positioning your wood-burning stove
Distance to furniture
Distance to flammable materials, shown with insulated flue pipe
Distance to flammable materials, shown with un-insulated flue pipe
Distance to firewall
Height adjustment of stove
Load bearing foundation
Floor plate
Existing chimney and pre-fabricated element chimney
Connection between stove and steel chimney
Requirements for chimney
Connection with 90° elbow pipe
Connecting piece / top outlet
Connecting piece / rear outlet
Fitting the natural stones/tiles
Fresh air intake
Closed combustion system
Indicator for control of air supply
Scan 64 open plinth
Scan 64 with right-hung wood compartment door
Accessories ............................................................................................................ 20
Fitting the top plate of natural stones/tiles
Handle
Instruction for use .............................................................................................. 22
CB technique
Primary air
Secondary air
Baffle plates
Ash drawer
Handle for riddling grate
Instructions for heating ................................................................................... 23
Lighting
Handling fuel
Maintenance ......................................................................................................... 25
Troubleshooting .................................................................................................. 28
T E C H N I C A L D ATA
3
Installation
The house owner is responsible for ensuring that all necessary national and local safety measures are observed during installation and fitting
and also responsible for observing the fitting and operating instructions detailed in this manual.
When you install any kind of fireplace or stove, you must inform the local authorities. You are also responsible for calling in a chimney sweep to
inspect and authorize the installation.
To ensure best-possible functionality and safety for your installation, we advise you to call a professional fitter. Our Scan Dealer will be able to
recommend a qualified fitter in your area. For information on Scan Dealers, please go to http://scan.dk.
Safety
Any changes made to the product by the dealer, installer or user could result in the product and safety functions not functioning as intended.
The same applies to the fitting of accessories or extra equipment not supplied by Scan A/S. This could also be the case if parts that are necessary
for the operation and safety of the stove are dismantled or removed.
The Scan 64 - series range comprises:
Scan 64-1: Stove with steel sides
Scan 64-2: Stove with steel sides and side windows
Scan 64-3: Stove with sides of natural stones/tiles
Scan 64-4: Stove with side windows and sides of natural stone/tile
Scan 64-7: Stove with stainless steel sides
Scan 64-8: Stove with stainless steel sides and side panes
Scan 64-1
Scan 64-2
Scan 64-3
Scan 64-4
Scan 64-7
Scan 64-8
4
T E C H N I C A L D ATA
Technical data and dimensions
Materials: ...................................... Steel plate, cast iron, galvanised sheet,
vermicolite
Surface treatment: ........................................................................... Senotherm
Max. wood length: ..................................................................................... 30 cm
Weight Scan 64-1 and Scan 64-2: .................................................... ca. 123 kg
Weight Scan 64-3: ..................................................................................... ca. 180
Intermittent fuelling means normal use of a woodstove. In other
words, you should let the fire die down until only the embers are left,
before refuelling.
The Scan 64 - series was build in compliance with the homologized
product type specified in the Assembly- and Instructions Manual
provided with the product.
The DoP declaration of performance is available from http://scan.dk
Weight Scan 64-4: ............................................................................... ca. 168 kg
Weight Scan 64-7 and Scan 64-8: .................................................... ca. 117 kg
Connecting piece internal diameter: ............................................... 144 mm
Connecting piece external diameter: .............................................. 148 mm
Approval type: ................................................................ Intermittent fuelling
Test in compliance with EN 13240
Technical data
Unit
CO Emission at 13% O2
Scan 64-1, Scan 64-3 and Scan 64-7
0,08
%
CO Emission at 13% O2
975
Dust @ 13% O2
< 20
mg/Nm3
mg/Nm3
Nox @ 13% O2
Efficiency
104
mg/Nm3
82
%
Nominel output
6
kW
Chimney temperature EN 13240
221
°C
Temperature in connecting piece
300
°C
5
g/sek
Amount of smoke
Sub-pressure EN 13240
Recommended sub-pressure in connecting piece
Required combustion air supply
12
Pa
15 - 18
Pa
Nm3/h
13,3
Fuel
Wood
Fuel consumption
2
kg/h
Amount of fuel
1,5
kg
Technical data
Unit
CO Emission at 13% O2
Scan 64-2, Scan 64-4 and Scan 64-8
0,1
%
CO Emission at 13% O2
1221
Dust @ 13% O2
< 20
mg/Nm3
mg/Nm3
Nox @ 13% O2
Efficiency
117
mg/Nm3
79
%
Nominel output
6
kW
Chimney temperature EN 13240
240
°C
Temperature in connecting piece
305
°C
Amount of smoke
6
g/sek
Sub-pressure EN 13240
12
Pa
Recommended sub-pressure in connecting piece
Required combustion air supply
15 - 18
Pa
12,5
Nm3/h
Fuel
Wood
Fuel consumption
2
kg/h
Amount of fuel
1,5
kg
5
T E C H N I C A L D ATA
1011*
210****
71
1131
154
1110**
90***
114
Dimension sketch
490
380
190
* Centre rear outlet
** Height to the begin ning of the connecting
piece at top outlet
*** Centre of fresh air intake bottom
**** Fresh air intake at the
back of the stove
NAVN:
Scan 64
EMNE:
Målskitse Scan 64
TG.NR:
VÆGT: N/A
MATERIALE:
DIMENSION:
STI:
AREAL:
C:\Working Folder\Designs\Scan 64\90064001.idw
N/A
DATO:
21-08-12
90064001
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
BC
6
T E C H N I C A L D ATA
Type plates
All Scan wood-burning stoves are fitted with a type plate, that specifies the approval standards and the distance to flammable materials.
The type plate is located at the back of the stove.
Type plate
Scan 64-2, Scan 64-4 & Scan 64-8
(With side windows)
Scan 64-1, Scan 64-3 & Scan 64-7
(Without side windows)
Scan 64-2 - 64-4 - 64-8
Scan 64-1 - 64-3 - 64-7
NAVN: fired
Freestanding room heater
Scanby
64 solid fuel
Standard:
EN 13240
MATERIALE:
EMNE:
Typeskilt og registreringsnummer
TG.NR: fired
Freestanding room heater
by solid fuel
90064010
DATO:
Standard:
AREAL:
DIMENSION:
Minimum distance to
combustible materials
STI:
VÆGT: N/A
EC no. 90064600
C:\Working Folder\Designs\Scan 64\90064010.idw
Side: 350 mm - Back: 150 mm - Front: 1000 mm
0,08%
CO emission at 13% O2:
Dust at 13% O2:
Flue gas temperature:
Nominal heat output:
Efficiency:
Fuel type:
Operation type:
The appliance can be operated in a shared flue.
975 mg/Nm³
< 20 mg/Nm³
300°C
6 kW
82%
Wood
Intermittent
Country Classification Certificate/Standard
Approved by
EUR
Intermittent
EN 13240
RWE Power AG
Klasse 2
300-ELAB-1528-NS Teknologisk Institut
Norway
15a B-VG
FSPS-Wa 2138-A
RWE Power AG
Austria
Schweiz LRV 11
VKF
Nr. 23448
RWE Power AG
Germany BStV
1 FSPS-Wa 2138-EN
RWE Power AG
3,2 - 7,3 kW
8,7 kW
Scheitholz
FSPS-Wa 2138-A
DK-5492 Vissenbjerg©
Side: 500 mm - Back: 150 mm - Front: 1000 mm
Scan A/S DK 5492 Vissenbjerg
0,10%
1221 mg/Nm³
CO emission at 13% O2:
Dust at 13% O2:
< 20 mg/Nm³
Flue gas temperature:
305°C
Nominal heat output:
6 kW
Efficiency:
79%
Fuel type:
Wood
Operation type:
Intermittent
The appliance can be operated in a shared flue.
Country Classification Certificate/Standard
Approved by
EUR
Intermittent
EN 13240
RWE Power AG
Klasse 2
300-ELAB-1528-NS Teknologisk Institut
Norway
15a B-VG
FSPS-Wa 2138-A
RWE Power AG
Austria
Schweiz LRV 11
VKF
Nr. 23448
RWE Power AG
Germany BStV
1 FSPS-Wa 2138-EN
RWE Power AG
Angaben für Österreich
Wärmeleistungsbereich:
Brennstoffwärmeleistung:
Zulässige Brennstoffe:
Prüfbericht:
3,3 - 6,7 kW
8,5 kW
Scheitholz
FSPS-Wa 2138-A
Follow assembly- and instructions manual.
Use only recommended fuels.
Montage- und Bedienungsanleitung beachten.
Verwenden Sie nur empfohlene Brennstoffe.
Follow assembly- and instructions manual.
Use only recommended fuels.
Montage- und Bedienungsanleitung beachten.
Verwenden Sie nur empfohlene Brennstoffe.
1000
EC no. 90064601
Krog Iversen
& Co A/S
Minimum distance
to combustible
materials
DIBt Zulassungsnummer: Z-43.12-296
DIBt Zulassungsnummer: Z-43.12-296
Angaben für Österreich
Wärmeleistungsbereich:
Brennstoffwärmeleistung:
Zulässige Brennstoffe:
Prüfbericht:
N/A
SIGN: BC
21-08-12
EN 13240
12-2012
1000
Scan A/S DK 5492 Vissenbjerg
12-2012
can 64
7
T E C H N I C A L D ATA
Product registration number
Additional accessories
All wood-burning stoves are provided with a product registration
number.
The product registration number is located at the back of the stove.
•
Small shaped floor plate in glass or steel
•
Large shaped floor plate in glass or steel
•
Natural stones/tiles top plate for stove with rear outlet
•
Natural stones/tiles top plate for stove with top outlet
Please make a note of this number on the front page as you will
always have to state it when contacting your dealer or Scan A/S.
Service box
The service box contains the following:
•
Fitting for connecting piece (not used for this Scan model)
• Seal
•
Safety fitting (not used for this Scan model)
•Plastic plugs for transport safety hole at the bottom of
the stove
• Various tools
Product
registration
number
• Glove
•
Fire starters for first lighting
Loose parts
Parts for use on right-hung door are supplied fastened to the pallet.
Other loose parts are located in the stove's ash drawer.
Scan 64, all types:
EMNE:
6400000
Typeskilt og registreringsnummer
VÆGT: N/A
AREAL:
rking Folder\Designs\Scan 64\90064010.idw
N/A
TG.NR:
DATO:
21-08-12
90064010
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
•
4 pcs. screws for fastening the connecting piece
•
1 pcs. indicator for control of air supply
•
1 pcs. screw M5 x 6, must be placed for United Kingdom.
BC
Scan 64-3 and Scan 64-4:
•
4,5 m gasket
Scan 64
E:
can 64
N:
8
A S S E M B LY
Remove packaging
Remove the protection between the baffle plates, before taking the
stove into use!
Check that the stove is not damaged before installing it.
Scan 64 is supplied attached to a wooden pallet. Remove the two
screws from the wood compartment store, as illustrated below, and
lift the stove off the wooden pallet.
Scan 64-7 and Scan 64-8:
We recommend that you leave the protective film on the side plates
until the fitting is complete.
Protection for baffle plates
Put back the upper plate on the pins, as the protection pushes the
plate upwards.
A
Remove the screws that securing the stove to the pallet.
A
Pin for baffle plate
Screws to be removed
Fit the plastic plugs from the service box into the transport protection
holes.
Brændeovn på palle
EMNE:
EMNE:
Brændeovn på palle
AREAL:
orking Folder\Designs\Scan 64\90064020.idw
AREAL:
rking Folder\Designs\Scan 64\90064020.idw
VÆGT: N/A
N/A
VÆGT: N/A
N/A
TG.NR:
21-08-12
90064020
BC
90064020
Krog Iversen & Co A/S
DATO: 21-08-12
SIGN: BC
DK-5492 Vissenbjerg©
Krog Iversen & Co A/S
DATO:
TG.NR:
SIGN:
DK-5492 Vissenbjerg©
9
A S S E M B LY
Installation:
Positioning your wood-burning stove
The wood-burning stove must be set up so that the stove itself, the
flue pipe, and the chimney can all be cleaned.
Distance to furniture: 1000 mm
But please check to avoid furniture or other furnishings being dried
out due to being too close to the stove.
All national and local requirements concerning safety distances for
wood burning stoves must be respected.
If you connect the stove to a steel chimney, the safety distances of the
steel chimney must also be respected.
Distance to flammable materials, shown with insulated flue pipe
The distances presuppose the use of an insulated flue pipe with min. 30 insulation all the way to the stove.
Scan 64-2, Scan 64-4 and Scan 64-8
(without side windows)
(with side windows)
240
240
50
50
Scan 64-1, Scan 64-3 and Scan 64-7
500
350
595
745
Parallel rear wall installation
778
513
250
578
6
53
313
3
25
50
Parallel rear wall installation
50
250
45° Corner installation
Scan 64
RIALE:
EMNE: Opstilling
mod brændbar væg, ovn uden sideruder
VÆGT: N/A
DATO:
TG.NR:
22-08-12
45° Corner installation
90064043
SIGN:
BC
NAVN:
Scan 64
EMNE: Opstilling
mod brændbar væg, ovn med sideruder
TG.NR:
90064003
10
A S S E M B LY
(without side windows)
(with side windows)
150
350
500
595
745
100
EMNE:
Brændbar + uisoleret røgrør - Scan 64 uden sideglas
VÆGT: N/A
ATERIALE:
IMENSION:
778
250
45° Corner installation
Scan 64
513
250
628
6
53
4
32
100
Parallel rear wall installation
363
Parallel rear wall installation
AVN:
TI:
340
Scan 64-2, Scan 64-4 and Scan 64-8
150
Scan 64-1, Scan 64-3 and Scan 64-7
340
Distance to flammable materials, shown with un-insulated flue pipe
AREAL:
C:\Working Folder\Designs\Scan 64\90064049.idw
N/A
DATO:
45° Corner installation
90064049
TG.NR:
23-08-12
SIGN:
BC
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
NAVN:
Scan 64
EMNE: brændbar
+ uisoleret røgrør - Scan 64 med sideglas
VÆGT:
MATERIALE:
DIMENSION:
STI: C:\Working
AREAL:
Folder\Designs\Scan 64\90064050.iam
N/A
N/A
DATO:
TG.NR:
23-08-12
900640
SIGN:
Scan A/S
DK-5492 Vissenbjerg©
BC
11
A S S E M B LY
Distance to firewall
110 mm brick or other material with a corresponding insulation ability.
The distances presuppose the use of an insulated flue pipe with min. 30 insulation all the way to the stove.
Scan 64-1, Scan 64-3 and Scan 64-7
(without side windows)
700
700
50
50
50
700
700
700
50
100
300
25
3
50
50
50
50
100
Flammable material
Flammable material
Firewall
Firewall
NAVN:
Scan 64
EMNE: Opstilling
til brandmur, scan 64 med sideglas
VÆGT: N/A
MATERIALE:
DIMENSION:
EMNE: Brandmur
860
860
700
50
700
700
50
700
700
100
100
700
25
3
760
960
100
4
32
25
3
960
960
50
50
800
50
700
50
700
Scan 64-2, Scan 64-4 and Scan 64-8
(with side windows)
og isoleret røgrør
- Scan
6464
uden sideglas
NAVN:
Scan
TG.N
DATO:
25-08-11
N/A
Scan A/
TG.NR:
EMNE: Brandmur
90064047og isoleret røgrør - Scan 64 uden sideglas
DK-5492TG.NR:
Visse
AREAL:
:
12
A S S E M B LY
Height adjustment of stove
Load bearing underlay
The Scan 64 has four adjustment screws under the stove. Use the
adjustment screws to get the stove to stand straight and level.
All of the products in our portfolio are classified as light-duty fireplaces; in most cases, there is no need to reinforce the floor, so that you
can typically use the normal floor.
Tilt the wood-burning stove and adjust the adjustment screws.
However, you should make sure that the load bearing underlay can
bear the weight of the wood-burning stove and that of the chimney.
If you are using a shaped floor plate, you should adjust the stove
upwards to allow the plate to be inserted under the front of the stove.
Floor plate
If you are setting up the stove on a flammable floor, observe national
and local regulations on the size of the non-flammable underlay that
covers the floor around the stove.
Your local Scan dealer can advise you on regulations concerning
flammable materials in the vicinity of your stove.
The idea behind the floor plate is that it protects the floor and flammable material against sparks.
The floor plate can be made of steel or glass, and the stove can be set
up on brick, natural stone or similar materials.
This Scan wood-burning stove has an integrated floor plate, and
can thus be set up on any flammable material without a protective
underlay.
Small shaped floor plate in glass or steel.
B
B
Large shaped floor plate in glass or steel
Ajustment screw
NAVN:
Scan 64
EMNE:
Justerskruer
VÆGT: N/A
RIALE:
:
Scan
NSION:
64
EMNE:
Justerskruer
AREAL:
AREAL:
DATO:
Scan 64
EMNE:
10-08-11
STI:
EMNE:
Scan 64 med lille gulvplade
SIGN:
BC
VÆGT: N/A
DATO:
DK-5492
Vissenbjerg©
SIGN:
10-08-11
N/A
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Ovn med vatterpas
TG.NR:
DATO:
90064053
VÆGT: N/A
AREAL:
C:\Working Folder\Designs\Scan 64\90064004.idw
90064044
Krog Iversen & Co A/S
C:\Working Folder\Designs\Scan 64\90064044.idw
NAVN:
DIMENSION:
TG.NR:
N/A
RIALE:
C:\Working
Folder\Designs\Scan 64\90064044.idw
NSION:
Scan 64
TG.NR:
MATERIALE:90064044
BC
N/A
TG.NR:
DATO:
29-08-12
90064004
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
BC
13
A S S E M B LY
Existing chimney and pre-fabricated element
chimney
Connecting piece / top outlet
If you intend to connect your stove to an existing chimney, it makes
sense to contact an authorised Scan dealer, or a local chimney sweep
for advice. These experts will also let you know if your flue needs
renovating.
The connecting piece is placed loosely in the top outlet of the stove.
The gasket for the connecting piece is in the service box.
The screws for fastening the connecting piece are in the stove’s ash
drawer.
When connecting a pre-fabricated element chimney, follow the
manufacturer’s connection instructions for the relevant chimney
type.
The stove is prepared from the factory for top outlet.
Lift the top plate and connecting piece off the stove.
Connection between stove and steel chimney
Your Scan dealer, or local chimney sweep, can advise you on choosing
a make and type of steel chimney. This ensures that the chimney
will match your wood-burning stove. As a general rule, the length of
the flue should not be less than 3,5 m measured from the top of the
wood-burning stove.
Some weather or installation conditions might require another
length.
Choosing the wrong length or diameter of steel chimney could
impair functionality.
Always observe the chimney vendor‘s instructions precisely.
Requirements for chimney
The chimney must be labelled T400 and G for soot testing.
Connection with 90° elbow pipe
If you intend to use an elbow pipe with the Scan 64, we recommend
the use of a curved elbow pipe to improve the draft.
If you are connecting your stove using a sharp elbow bend, the cleanout door should be in the vertical section, such that the horizontal
part can be cleaned through it.
Mount the ceramic gasket on the connecting piece
Connecting
piece
NAVN:
Scan 64
MATERIALE:
Ceramic
gasket
EMNE:
Afmontage topplade + røgstuds
VÆGT: N/A
AREAL:
DIMENSION:
STI:
TG.NR:
DATO:
N/A
Scan 63
MATERIALE:
EMNE:
SIGN
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
C:\Working Folder\Designs\Scan 64\90064013.idw
NAVN:
30-08-12
90
Røgstuds med pakning
TG.NR:
VÆGT: 0,70
kg
DATO:
03-06-09
90063020
SIGN:
BC
14
A S S E M B LY
Connection piece / rear outlet
Fasten the connecting piece with screws from the ash drawer and
replace the top plate.
The stove is prepared from the factory for top outlet.
The connecting piece is placed loosely in the top outlet of the stove.
The gasket for the connecting piece is in the service box.
The screws for fastening the connecting piece are in the stove’s ash
drawer.
Lift the top plate and connecting piece off the stove.
C
C
4 pcs. M5x10 mm screw
Mount the ceramic gasket on the connecting piece
can 64
EMNE:
Montage af røgstuds i topafgang
TG.NR:
VÆGT: N/A
NAVN:
Scan 64
AREAL:
N/A
EMNE:
orking Folder\Designs\Scan 64\90064014.idw
MATERIALE:
DIMENSION:
DATO:
30-08-12
90064014
SIGN: BC
Connecting
piece
Krog Iversen
& Co A/S
Montage af røgstuds
i topafgang
EMNE:
Scan 64
DK-5492 Vissenbjerg©
Ceramic
VÆGT: N/A
MATERIALE:
gasket
NAVN:
AREAL:
DIMENSION:
N/A
TG.NR:
90064014
Afmontage topplade + røgstuds
DATO:
SIGN: BC
30-08-12 VÆGT:
N/A
TG.NR:
DATO:
30-08-12
90
SIGN:
Krog AREAL:
IversenN/A
& Co A/S
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
STI: C:\Working Folder\Designs\Scan 64\90064013.idw
STI: C:\Working Folder\Designs\Scan 64\90064014.idw
DK-5492 Vissenbjerg©
NAVN:
Scan 63
EMNE:
Røgstuds med pakning
DIMENSION:
TG.NR:
VÆGT: 0,70
MATERIALE:
AREAL:
93327 mm^2
kg
DATO:
03-06-09
90063020
SIGN:
BC
can 64
64
15
A S S E M B LY
Cut off the cover plate from the rear plate with cutting pliers at the
fastening points.
Lift the heat shield off the stove and cut the cover plate free using
cutting pliers at the fastening points and remove.
D
D
NAVN:
Scan 64
EMNE:
Varmeskjold løftes af ovn
VÆGT: N/A
MATERIALE:
AREAL:
DIMENSION:
STI: C:\Working Folder\Designs\Scan 64\90064052.idw
Afmontage dækplade for bagafgang
FasteningEMNE:
points
Afmontage dækplade for bagafgang
EMNE:
VÆGT: N/A
VÆGT: N/A
AREAL: N/A
AREAL: N/A
rking Folder\Designs\Scan 64\90064012.idw
g Folder\Designs\Scan 64\90064012.idw
TG.NR: 90064012
TG.NR: 90064012
DATO: 30-08-12
SIGN:
DATO: 30-08-12
SIGN: BC
Krog Iversen & Co A/S
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
DK-5492 Vissenbjerg©
BC
N/A
TG
DATO:
31-08-12
Krog Iversen &
DK-5492 Visse
16
A S S E M B LY
Remove the cover. This is to be used later as a seal and cover at the top
of the smoke outlet.
Fit the cover and tighten it. Replace the top plate.
Dæksel
Fit the connecting piece with the four screws found in the stove’s ash
drawer. Hook the heat shield onto the stove.
E
NAVN:
EMNE:
MATERIALE:
Afmontage dæksel for bagafgang
DIMENSION:
VÆGT: N/A
AREAL:
DATO:
STI:
N/A
E
older\Designs\Scan 64\90064025.idw
NAVN:
Scan 64
TG.NR:
31-08-12
EMNE:
Montage af dæksel i topafgang
VÆGT: N/A
90064025
SIGN:
AREAL:
BC
N/A
DATO:
30-08-12
90
SIGN
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
C:\Working Folder\Designs\Scan 64\90064028.idw
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
4 stk. M5x10 mm skrue
Scan 64
EMNE:
Montage af røgstuds i topafgang
VÆGT: N/A
MATERIALE:
DIMENSION:
TG.NR:
AREAL:
N/A
T
DATO:
30-08
Krog Iverse
17
A S S E M B LY
Fitting the natural stones/tiles
The delivered gasket (4,5 m) should be cut in appropiate lengths and
sticked onto the sides of the stove as shown below.
Scan 64-3 and Scan 64-4 are delivered with loose natural stone/tiles
plates for mounting on the sides of the stove.
It is a natural material, wherefore there might be differences in structure and form.
Scan 63-3 (without side windows)
Each natural stone/tile must be mounted with distance bushings and
screws which are already mounted in the stones.
Gasket
Scan 63-4 (with side windows)
Gasket
NAVN:
Scan 64
EMNE:
Scan 64-3 og Scan 64-4 m. isoleringsbå
VÆGT: N/A
MATERIALE:
AREAL:
DIMENSION:
STI:
C:\Working Folder\Designs\Scan 64\90064046.idw
Gasket
EMNE: Fedtstenssæt
for sideglas
VÆGT:
AREAL:
older\Designs\Scan 64\10064904.iam
N/A
TG.NR:
N/A
DATO:
17-08-2011
10064904
SIGN:
Scan A/S
DK-5492 Vissenbjerg©
pcj
N/A
18
A S S E M B LY
Fresh air intake
Hook the natural stone/tile sides onto the stove.
In a well-insulated house, the air used up by the burning process
has to be replaced. This particularly applies to houses with mechanical ventilation. There are different ways of making sure that an air
exchange takes place. The most important thing is to ensure that
there is a supply of air to the room where the wood stove is located.
The external wall vent must be located as close to the wood stove as
possible, and you must be able to close it when you are not using the
wood stove.
National and local building regulations must be followed with
regard to the connection of fresh-air intake.
Closed combustion system
You should use the closed combustion system for the wood-burning
stove if you live in a newly-built, airtight home. Outside air for combustion is connected through a ventilation pipe via the wall or floor.
It must not be possible to shut off the ventilation pipe with a valve
•
Minimum Ø100 mm ventilation pipe, maximum length: 6 m
with a maximum of one bend
H
Remove the cover plate at the back of the stove or the cover plate at
the bottom of the wood compartment store, as shown on page 15.
Connect outside air to the connection piece underneath the combustion chamber.
H
External combustion air via wall
External combus-tion
air via floor
64
Montage af fedtstenssider
EMNE:
Montage af fedtstenssider
EMNE:
VÆGT: N/A
VÆGT: N/A
AREAL: N/A
AREAL: N/A
ng Folder\Designs\Scan 64\90064032.idw
Folder\Designs\Scan 64\90064032.idw
TG.NR: 90064032
TG.NR: 90064032
DATO: 29-08-12
SIGN: BC
DATO: 29-08-12
SIGN: BC
Krog Iversen & Co A/S
Krog
IversenVissenbjerg©
& Co A/S
DK-5492
DK-5492 Vissenbjerg©
A S S E M B LY
19
Indicator for control of air supply
Scan 64 with open plinth
The indicator for control of air supply is provided loose and comes in
the stove’s ash drawer. Fit the indicator to the wood compartment
door as shown below. If you choose to remove the stove’s wood compartment door, you can fit the indicator onto the handles.
If you want your Scan 64 with open plinth, remove the wood compartment door and its stop as well as the large cover plate at the back of
the stove (see page 15).
Divide the indicator in the middle and carefully remove the film.
Cover plate to
be removed
Fit to the stove’s wood compartment door as shown below.
NAVN:
Scan 64
EMNE:
Typeskilt og registreringsnummer
VÆGT: N/A
MATERIALE:
DIMENSION:
STI:
AREAL:
C:\Working Folder\Designs\Scan 64\90064010.idw
N/A
TG.NR:
DATO:
21-08-12
90064010
SIGN:
BC
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Remove the tape carefully.
Do not remove
the radiation
plate
can 64
20
A S S E M B LY / A C C E S S O R I E S
Scan 64 with right-hung wood compartment door
Fitting the top plate of natural stone/tile
If you want your Scan 64 with a right-hung wood compartment door,
move the bracket and the door stop in the wood compartment store,
and then turn round and fasten the door.
You can buy a natural stone/tile top as an accessory. Place the stone
top on the steel top plate.
Fitting the natural stone/tile top
NAVN:
EMNE:
Scan 64 med fedtstensplade for topafgang
VÆGT: N/A
MATERIALE:
AREAL:
DIMENSION:
EMNE:
Scan 64 med højrevendt luge
VÆGT: N/A
:
:
Scan 64
AREAL:
orking Folder\Designs\Scan 64\90064042.idw
N/A
STI:
C:\Working Folder\Designs\Scan 64\90064017.idw
TG.NR:
DATO:
29-08-12
90064042
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
BC
N/A
TG.NR:
DATO:
29-08-12
9006401
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
BC
21
ACC ESSOR I ES
Handle
Black handles are available as an option. Mount the handles on the stove as shown below.
1
Remove the handle screw
5
2
Remove the handle
6
3
Fit the black handle
7
Remove the handle
4
Tighten the handle
8
Tighten the black handle
Screws to be removed (picture 5+6)
22
I N S T R U C T I O N S F O R H E AT I N G
A
CB-technique (Clean Burning)
Baffle plates
The wood-burning stove is equipped with CB technology. In order to
ensure an optimal combustion of released gases under the incineration process, air will pass through a specially developed canal system.
The heated air is led into the combustion chamber through the small
holes at the rear of the burn chamber. This airflow is driven by the
combustion rate and thus cannot be regulated.
The baffle plates are located in the upper part of the combustion
chamber. The plates hold back smoke, making sure it stays inside
the combustion chamber for a longer time before escaping through
the chimney. This reduces the smoke gas temperature as the gases
have more time to dissipate heat to the wood-burning stove. The
baffle plates must be removed for sweeping; see „Maintaining your
wood-burning stove“. Note that the baffle plates are made of porous,
ceramic material, and can break. Exercise care when working. The
baffle plates are subject to wear and tear, and are not covered by the
warranty.
Primary air
The primary air regulation mechanism is used for lighting the fire, or
to boost the burning process when you put wood on. The primary air
vent can be 0 - 30% open if you use hard wood fuel such as oak and
beech. You can close the primary air vent if you use soft wood such
as birch or pine for fuel.
Settings for normal load: 0 - 30%
Secondary air
Secondary air is pre-heated and fed indirectly to the fire. At the same
time, the secondary airflow cleans the glass pane to avoid soot buildup. If you over-restrict the secondary airflow, soot can build up on the
glass pane. The secondary airflow determines the heat output from
your wood stove.
Settings for normal load: 50 - 70%
Ash drawer
Open the glass door to access the ash pan which is located below the
combustion chamber.
Keep the ash pan closed at all times when the wood stove is lit.
The ash drawer must not be overfilled and must therefore be emptied at regular intervals.
Handle for riddling grate
Your wood stove is fitted with a riddling grate which empties the
ash from the combustion chamber into the ash pan when activated.
The riddling grate must be in semi-open position while the wood
stove is lit.
Adjustment of air supply,
primary and secondary damper
Baffle plates
B
CB-technique
100% - 0%
NAVN:
Scan 64
0% - 100%
The Clean
Air
Act 1993 and Smoke Control Areas TG.NR:
Spjæld, askeskuffe og støbejernsbund
EMNE:
900640
Under the Clean Air Act local authorities may declare the whole or
DATO: area.
SIGN: BC
MATERIALE:
30-08-12
part of the district of the authority VÆGT:
to be N/A
a smoke control
It
is
an
offence
to
emit
smoke
from
a
chimney
of
a
building,
from
a
AREAL: N/A
DIMENSION:
Krog Iversen & Co A/S
furnace or from any fixed boiler if located in a designated smoke
DK-5492
Vissenbjerg©
STI: C:\Working Folder\Designs\Scan
control area. 64\90064037.idw
It is also an offence to acquire an "unauthorised fuel"
for use within a smoke control area unless it is used in an "exempt"
appliance ("exempted" from the controls which generally apply in
the smoke control area).
powers under the Act to authorise smokeless fuels or exempt appliances for use in smoke control areas in England. In Scotland and
Wales this power rests with Ministers in the devolved administrations for those countries. Separate legislation, the Clean Air (Northern
Ireland) Order 1981, applies in Northern Ireland. Therefore it is a
requirement that fuels burnt or obtained for use in smoke control
areas have been "authorised" in Regulations and that appliances
used to burn solid fuel in those areas (other than "authorised" fuels)
have been exempted by an Order made and signed by the Secretary
of State or Minister in the devolved administrations.
Further information on the requirements of the Clean Air Act can be
found here : http://smokecontrol.defra.gov.uk/
Handle for riddling grate
NAVN:
Scan 64
EMNE:
Brændkammerforing
VÆGT: N/A
MATERIALE:
AREAL:
DIMENSION:
STI:
N/A
C:\Working Folder\Designs\Scan 64\90064036.idw
Your local authority is responsible for implementing the Clean Air Act
1993 including designation and supervision of smoke control areas
TG.NR: 90064036
and you can contact them for details of Clean Air Act requirements”
DATO: 13-07-11
SIGN: BC
The secondary air valve has been modified, so that is does not close
completely but has an opening corresponding to the position used at
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
the lowest emission test.
You can use any type of untreated well seasoned wood as fuel.
Primary air
Secondary air
Ash drawer
The Scan 64 has been recommended as suitable for use in smoke
control areas when burning wood and fitted with a mechanical stop
to prevent secondary air control closure beyond the 35mm open
position .
nd
AL:
23
I N S T R U C T I O N S F O R H E AT I N G
Important!
Dampers left open
This screw (M5 x 6) must be placed as shown in the picture,
to prevent secondary air control closure beyond the 35mm open
position .
Operation with the air controls or appliance dampers open can
cause excess smoke. The appliance must not be operated with air
controls, appliance dampers or door left open except as directed in
the instructions.
Environmentally-Friendly Heating
Avoid restricting your wood-burning stove to an extent where no
flames are visible during the degasifying period, as this leads to particularly inefficient heating. The gases released by the wood do not
burn due to the low temperature in the combustion chamber. Part
of the gas condenses in the wood-burning stove and flue system as
soot, and this could lead to your chimney catching fire. The smoke
that exits the chimney is bad for the environment and has an unpleasant smell.
Lighting
We recommend the use of fire starters, or similar products, which are
available from your Scan dealer. Using fire starters helps to light the
wood quicker, and keeps the burning process clean.
Never use liquid lighting fuels!
"Top down" optænding
4 pieces of wood approx. 20 - 23 cm long with a weight of approx. 0.5
– 0.6 kg per piece (image 1).
12 - 20 thin sticks of about 20 cm with a total weight of approx. 0,8 1,0 kg (image 2 - 5).
A
4 fire starters (image 6).
Place logs, sticks and fire starters in the combustion chamber as
shown on images 1 - 5.
A
N.GT
D
:R
TA
2 :O
bnU :RN.GT
okar
-40-7 OTAD
mm4 okarbnU IS 7002-40-72 :
mm4 CB :NGIS 7002
:NG
nacS -KD
CB
S/A nac2
S945
/A siV 945-KD
2
jbSnes
©grejbnessiV
e
r
g
©
A/N
A/N
V
:TGÆ
V
:TGÆ
N
:NVA
N
:NVA
AM
IRET M
:ELA
TA
dalP :ELAIRE ID
.ts ,e
042 ts ,edalP :NOISNEMID
.
M
SNE
042
S
:NOI
\:C :IT
ikroW\:C :ITS
F gn
W
redloF gnikro
\
D
e
sngiseD\redlo
\
B
y
g sngis
RA
\
:LAE
sgnin
A/N :LAERA bnU\eledsgningyB
A/N m4 okarbnU\eled
tpi.mm4 okar
m
.
i
tp
E
:ENM
E
:ENM
Set the primary and secondary airflow controls to maximum for
about 20 - 30 minutes. When the larger pieces of wood have caught
fire properly, you can set the primary and secondary airflow to the
desired level.
"Top down" lighting gives a more environmentally friendly start to
your fire and helps to keep the glass area as clean as possible.
1.
NAVN:
Scan 64
EMNE:
Skrue til england
TG.NR:
VÆGT: N/A
MATERIALE:
Refuelling on to a low fireN/Abed
DIMENSION:
STI:
AREAL:
C:\Working Folder\CAD\Inventor 2015\Templates\Standard - Manual.idw
DATO:
24-03-2015
90064053
SIGN:
hms
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
If there is insufficient burning material in the firebed to light a new
fuel charge, excessive smoke emission can occur. Refuelling must be
carried out onto a sufficient quantity of glowing embers and ash
that the new fuel charge will ignite in a reasonable period. If there
are too few embers in the fire bed, add suitable kindling to prevent
excessive smoke
Fuel overloading
TG.NR: 90064053
The maximum amount of fuel specified in this manual should not be
exceeded, overloading can cause excess smoke.
DATO: 24-03-2015 SIGN: hms
VÆGT: N/A
N/A
Standard
Operation with door left open
Operation with the door open
canIversen
cause excess
smoke.
Krog
& Co
A/SThe appliance
must not be operated with the appliance door left open except as
DK-5492 Vissenbjerg©
in the instructions.
- directed
Manual.idw
Dampers left open
Operation with the air controls or appliance dampers open can
cause excess smoke. The appliance must not be operated with air
controls, appliance dampers or door left open except as directed in
the instructions.
2.
24
I N S T R U C T I O N S F O R H E AT I N G
3.
Using your stove in the spring or autumn
In the transition period (spring/autumn), where there is less need
for heating, we recommend to make a single „top down“ lighting,
perhaps with one stoke up to ensure that the combustion chamber
lining burns clean again.
Why you need a chimney
The chimney is the wood-burning stove‘s motor; it‘s performance
decides how well your stove will work. The draft in the chimney
creates a vacuum in the wood-burning stove. The vacuum draws the
smoke out of the stove, and takes in air through the combustion air
baffle to fuel the burning process. Combustion air is also used for the
airwash system that keeps the window clear of soot.
The draft in the chimney is caused by the difference in temperatures
inside and outside the chimney. The higher the temperature difference is, the better the draft in the chimney will be. It is thus important
for the chimney to reach operating temperature before you adjust
the damper to restrict combustion in the stove (a brickwork chimney
will take longer to reach operating temperature than a steel chimney). It is very important to reach operating temperature as quickly
as possible on days on which the draft in the chimney is poor due to
unfavorable wind and weather conditions. Make sure the fuel ignites
as quickly as possible (with visible flames). Chop the wood into particularly small pieces; use an extra fire lighter etc.
After longer periods of disuse, check the chimney flue for blockage.
You can connect several units to the same chimney. But make sure
check with your chimney sweep to observe local regulations.
No matter how good your chimney is, it will not perform well if you do
not use it correctly. On the other hand a poor chimney, may give you
acceptable results if you use it correctly.
4.
Fire starters
5.
Using your stove in various weather conditions
Wind blowing on the chimney can have a great effect on how your
stove reacts in various wind conditions; you may need to adjust
the airflow to achieve good burning results. Fitting a damper in the
flue pipe may also help as it will give you the ability to regulate the
draught in changing wind conditions.
Fog can also have a great influence on how well a chimney draws;
you may again need to adjust the airflow settings to achieve good
burning results.
General Notes
Please note! Parts of the wood-burning stove, especially the outer
surfaces, become hot during use. Please exercise due care.
Never empty ashes into a flammable container. Ashes can contain
glowing embers long after you finish using your wood stove.
While the stove is not in use you can close the valves to avoid draught
through the stove.
Continuous firing
It is important to reach as high a temperature as possible in the
combustion chamber. This makes the most efficient use of the wood
stove and fuel, and ensures a clean burning process. At the same
time, this avoids soot build-up on the combustion chamber walls and
glass. While the stove is lit, you should not see any smoke, but just air
movement that indicates the burning process.
After completing the lighting phase, you should have a good layer of
embers in the wood stove; you can then start stoking up the stove. Lay
2-3 pieces of wood, of about 0.4 - 0.6 kg weight with a length of about
25 cm onto the fire.
Note! The wood must catch fire quickly; this is why we recommend
setting the primary airflow to full power. Running the stove at too
low a temperature and with too little primary air can lead to deflagration of the gases, and thus cause damage to the stove.
When stoking up with wood, always open the glass door carefully to
avoid smoke escaping. Never stoke up with wood while the fire is still
burning nicely.
After longer breaks you should check the smoke outlet paths for
blockages before lighting.
Chimney fires
In case of a chimney fire, keep the stove door, the ash container, and
the valves on the stove closed. In case of emergency, call the fire service.
It is recommended that you get a chimney sweep to check the chimney before using the stove again.
25
MAINTENANCE
Handling fuels
Maintaining your wood-burning stove
Selecting Wood/Fuel
Apart from regular chimney sweeping, your wood-burning stove
does not require any regular maintenance. However, we recommend
servicing at least once every two years
You can use any type of wood as firewood, however, harder types,
such as beech, ash, are generally better for heating as they burn more
evenly and create less ash. Other wood types like maple, birch and
spruce are excellent alternatives.
Handling
Firewood is best if you fell the tree, and saw and split the wood,
before May 1st. Remember to cut the logs to match the size of your
wood-burning stove‘s combustion chamber. We recommend a diameter of 6-10 cm. The length should be about 6 cm shorter than that
of the combustion chamber to leave enough space for air to circulate.
Firewood with a greater diameter needs splitting. Split wood dries
faster.
Storing
Use only original replacement parts for maintenance and repairs of
your stove.
Note! Make sure the wood-burning stove is cold before starting
maintenance or repair work.
Coated surfaces
Clean your wood-burning stove by dusting with a dry, lint-free cloth.
If the topcoat is damaged, you can purchase a repair spray from your
authorised Scan dealer. As slight differences in colour are possible,
spray a larger area to achieve a natural transition for best results.
For best results, apply repair spray when the wood-burning stove is
hand-hot.
You need to store the sawn and split firewood in a dry place for 1-2
years before burning. Wood dries faster if you stack it in an airy place.
Before use, store the firewood for a few days at room temperature.
Note that wood absorbs moisture during the autumn and winter
seasons.
Cleaning the glass
Moisture
Even if you follow all of our instructions, a slight film of soot can build
up on the glass. You can easily remove this build up by cleaning with
a dry cloth and glass cleaner. Please note that the glass cleaner is not
to get into contact with the gaskets, as this can discolour the glass
permanently.
To avoid environmental issues, and for optimum burning, wood
has to be perfectly dry to be suitable for use as firewood. The max.
residual moisture in the wood should not exceed 20%. A moisture
content of 15-18% yields best results. As an easy way of checking if
wood is dry, just knock two pieces of wood together. If the wood is
moist, the sound will be dull.
If you use damp wood, most of the heat it produces will be used to
evaporate the water. The temperature in the wood stove does not
rise, and the room is not sufficiently heated. Of course, this is not
economical, and it will cause soot build up on the glass pane, in the
stove, and in the chimney. Burning moist wood also causes pollution.
Understanding units for measuring wood
Various units of measurement are used for wood. Before you buy wood,
it makes sense to familiarise yourself with the terms. There are various
brochures, in public libraries for example, that cover this topic.
Use of the following as fuel is illegal
Painted, pressure impregnated, or glued wood, driftwood from the
sea. Never burn chipboard, plastics, or chemically treated paper.
These materials are dangerous to humans, to the environment, your
wood stove, and your chimney. To keep a long story short – make sure
you burn only quality firewood.
Firewood fuel value
The fuel value is different for different types of wood. In other words,
you need to use more wood of certain types to achieve the same heating performance. This Instruction Manual assumes that you will be
using beech, which has a very high fuel value, and is also a wood that
is easy to procure. If you use oak or beech wood fuel, note that these
wood types have a greater fuel value than, say, birch. Make sure you
use less fuel to avoid damage to the wood-burning stove.
Wood types
Kg Dry wood/m3 Compared to
beech
Hornbeam
Beech/Oak
Ash
Maple
Birch
Pine
Fir
Poplar
640110%
580100%
57098%
54093%
51088%
48083%
39067%
38065%
Our wood-burning stoves are designed to prevent serious soot build
up on the glass. The best way to achieve this is to make sure you have
a sufficient combustion air supply. It is also important to use dry
wood, and have a correctly dimensioned chimney.
Combustion chamber lining
Slight cracks can appear in the combustion chamber lining due to
moisture, or to the heating/cooling process. These cracks have no
influence on the heating performance or lifetime of your stove.
However, if the lining starts to crumble, you must replace it. The combustion chamber lining is not covered by the warranty.
Gaskets
All wood-burning stoves have gaskets made of ceramic material fitted
to the stove, the doors, and/or the glass. These gaskets are subject to
wear and tear, and must be replaced when necessary.
Chimney sweeping and cleaning your
wood-burning stove
Follow national and local chimney sweeping regulations. We
recommend having the wood-burning stove cleaned regularly by the
chimney sweep.
Before starting to clean your wood-burning stove, and sweep the flue
pipe, we recommend first removing the baffle plates.
Checking the stove
Scan A/S recommends that you check your stove thoroughly after
sweeping/cleaning. Check all visible surfaces for cracks. Check that
all joints are tight and that the seals sit correctly. Worn or deformed
seals should be replaced.
Servicing
• We recommend that the stove should have a comprehensive
servicing at least once every two years. Servicing should include
the following:
• Adjust handles and door
• Lubricate hinges using copper grease
• Check gaskets. Replace any that are broken or weak.
• Check combustion chamber door and riddling grate
• Check combustion chamber lining and baffle plates.
The stove must be serviced by a qualified fitter. Use only orignal
spare parts.
nVN:
64
26
MAINTENANCE
Service
Baffle plates and combustion chamber lining
Be very careful when removing the baffle plates from the stove.
Lift up the lower baffle plate, remove the pins and take out the baffle plate.
Lift the upper baffle plate to the back of the combustion chamber. Remove pins. Pull the plate free from the baffle plate holder and remove it.
Lift the combustion chamber lining’s sides, remove them from the rear cover and take them out.
Note that the combustion chamber lining’s sides support the rear cover so this could fall when the sides are removed.
Remove the rear cover.
A
A
Upper baffle
plate
Lower baffle
plate
NAVN:
Scan 64
EMNE:
Snit igennem
Upper ovn
baffle plate
TG
Holder for
upper bafDATO: 29-08-1
VÆGT: N/A
fle plate
MATERIALE:
AREAL:
DIMENSION:
STI:
C:\Working Folder\Designs\Scan 64\90064033.idw
Scan 64-1, Scan 64-3 and Scan 64-7
Scan 64-2, Scan 64-4 and Scan 64-8
(without side windows)
(with side windows)
Scan 64
EMNE:
Snit
igennem
Snitovn
igennem ovn
EMNE:
TG.NR:
TG.NR: 90064033
90064033
N/A
Krog Iversen
DK-5492 Viss
27
T R O U B L E S H O OT I N G
Smoke escaping
Warranty
• Damp wood
All wood-fired Scan products are made of high-quality materials and
subject to strict quality controls before leaving the factory. We give a
warranty of 5 years on manufacturing errors or defects.
• Chimney not drawing properly
• Chimney is not properly dimensioned for the stove
• Check if the smoke gas pipe/chimney are blocked
• Is the chimney the right height for its surroundings?
•At rear outlet, check that the flue pipe does not obstruct the
chimney draught
• Vacuum in room
•The door is opened before the embers have burned down
­sufficiently
Wood burning too quickly
• The air valves are set incorrectly
• The baffle plates is incorrectly mounted or missing
• Inferior firewood (waste wood, pallets etc.)
• Chimney too large
Soot build-up on glass
• Incorrect secondary airflow setting
• Excessive primary air
• Damp wood
• Wood pieces too large on lighting
• Inferior firewood (waste wood, pallets etc.)
• Chimney not drawing sufficiently
• Vacuum in room
Excessive soot build-up in chimney
• Poor burning (more air required)
You must quote your stove‘s product registration number when you
contact us or your authorised Scan dealer with a warranty claim.
The warranty covers all parts which in the opinion of Scan A/S require
repair or replacement due to manufacturing or construction error
The warranty applies to the original purchaser of the product only,
and is not transferable (except on prior sale).
The warranty covers only damage caused by manufacturing or construction errors.
The following parts are not covered by the warranty
•Wear and tear parts, such as the combustion chamber liners,
baffle plates, riddling grate, glass, tiles, and seals (except for
defects which were present on delivery).
•Defects caused by external chemical and physical influences
during transportation, storage and assembly, or at a later time.
•Soot build-up caused by poor chimney draught, damp wood, or
improper use.
• Costs of additional heating in connection with a repair.
• Transport costs.
• Costs for setting up, removing the wood stove.
This warranty is void
•In case of incorrect installation (the installer is responsible for
observing and complying with legal requirements and local
bylaws, along with this Assembly- and Instructionsmanual for
the wood-burning stove and accessories).
• In case of improper use, and/or use of prohibited fuels, nonoriginal spares (see this Assembly- and instructions manual).
•If the product registration number of the stove has been removed or damaged.
• Damp wood
•In case of repairs that do not comply with our instructions or
instructions by an authorised Scan dealer.
The surface of the stove is turning grey
•In case of any manipulation of the original state of this Scan
product or its accessories.
• Overheating (see instructions for heating)
•This warranty is only valid in the country to which this Scan
product was originally supplied.
Poor heating performance of stove
• Damp wood
• Not enough wood
• Inferior wood quality with low fuel value
• Baffle plates are not fitted correctly
Odour coming from stove
•The lacquer on the stove hardens when you use the stove for the
first time; this can cause an odour. Open a window or a door for
ventilation, and make sure the stove is heated up sufficiently to
avoid odours later.
•When heating up and cooling down, the stove may make some
clicking noises. These are due to the huge temperature differences to which the material is exposed and do not indicate any
product defects.
Always use original replacement parts, or parts recommended by the
manufacturer.
Version:
GB 90064500
24.03.2015
Scan A/S - DK-5492 Vissenbjerg