Service
Home
Automatic
Washers
Refer to Page 5 for Model Numbers
W424SE1A
www.comlaundry.com
Part No. 39311R3
November 2001
Table of Contents
Section 1 – Safety Information ............................3
Locating an Authorized Servicer .............................4
Section 2 – Introduction
Model Identification.................................................5
How Your Washer Works........................................8
Customer Service ...................................................10
Nameplate Location ...............................................10
Section 3 – Troubleshooting
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
No Hot Water...................................................11
No Cold Water .................................................11
No Warm Water...............................................12
Water Fill Does Not Stop At Proper Level......12
Timer Does Not Advance ................................13
Motor Does Not Run .......................................14
No Agitation ....................................................15
Constant Agitation ...........................................15
Washer Overheats, Cycles On Motor Thermal
Protector, Switch Actuator Kicks In
And Out............................................................16
Slow Spin Or No Spin .....................................16
Constant Spin...................................................17
Washer Stops In Cycle; Quits After A Couple
Loads; Is Intermittent .......................................17
Washer Is Locked Up Or Binding ...................17
Outer Tub Does Not Empty .............................18
Excessive Vibration .........................................18
Water Leaking From Outer Tub ......................18
Section 4 – Grounding
17. Wall Receptacle Polarity Check ......................19
18. Power Cord to Connection Block, Connection
Block to Control Hood Rear Panel; Models with
Suffixes B3069, 3050 and 3062.......................20
19. Power Cord To Cabinet Top, Cabinet Top To
Control Hood Mounting Bracket, Pressure
Switch Mounting Bracket And Ground Tab On
Graphic Panel...................................................21
20. Control Hood Wire Harness To Top Left Rear
Corner Gusset Of Cabinet ................................22
21. Wire Harness to Motor ....................................23
Section 5 – Service Procedures
22.
23.
24.
25.
Control Hood Assembly ..................................25
Timer................................................................30
Temperature Switch.........................................32
Pressure Switch................................................32
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
Graphic Panel...................................................32
Loading Door...................................................33
Agitator ............................................................34
Agitator, Drive Bell And Seal Assembly ........34
Front Panel.......................................................38
Motor And Mounting Bracket .........................39
Idler Lever And Pulley ....................................43
Motor Switch ...................................................44
Pump Assembly (Electric Pump Models) .......45
Cabinet Top Assembly ....................................47
Door Switch .....................................................48
Mixing Valve Assembly ..................................49
Washtub And Balance Ring.............................50
Hub And Seal Kit Assembly ...........................54
Outer Tub.........................................................58
Drive Pulley, Helix And Brake........................61
Weldment And Bearing Assembly ..................65
Transmission Assembly...................................67
Upper Bearing Assembly.................................73
Friction Ring....................................................74
Section 6 – Adjustments
46. Leveling Legs ..................................................77
47. Pressure Switch................................................78
48. Belt (Agitate And Spin) ...................................78
Section 7 – Test Procedures
49. Motor Test Procedure ......................................79
50. Mixing Valve Solenoid Test Procedure...........80
51. Temperature Switch Test Procedure................80
Section 8 – Cycle Sequence Charts
Timer No. 37925 Cycle Sequence ..........................81
Timer No. 37927 Cycle Sequence ..........................82
Timer No. 37928 Cycle Sequence ..........................83
Timer No. 37929 Cycle Sequence ..........................84
Timer No. 37930 Cycle Sequence ..........................85
Timer No. 37931 Cycle Sequence ..........................86
Timer No. 37995 Cycle Sequence ..........................87
Timer No. 39445 Cycle Sequence ..........................88
Section 9 – Internal Wiring of Washer Motor
Switch
Motor Assembly (1 Speed Motors).........................89
Motor Assembly (2 Speed Motors).........................90
© Copyright 2001, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without
the expressed written consent of the publisher.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Notes
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 1
Safety Information
Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,”
“WARNING,” and “DANGER”) followed by specific instructions. These precautions are intended for the personal
safety of the operator, user, servicer and those maintaining the machine.
a DANGER
Danger indicates the presence of a hazard that will cause severe personal injury, death or substantial property
damage if the danger is ignored.
a WARNING
Warning indicates the presence of a hazard that can cause severe personal injury, death or substantial property
damage if the warning is ignored.
a CAUTION
Caution indicates the presence of a hazard that will or can cause minor personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.
IMPORTANT
The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will
occur if the procedure is not followed.
NOTE
The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is
important but not hazard related.
In the interest of safety, some general precautions relating to the operation of this machine follow.
WARNING
• Failure to install, maintain and/or operate this product according to the manufacturer’s
instructions may result in conditions which can produce serious injury, death and/or property
damage.
• Do not repair or replace any part of the product or attempt any servicing unless specifically
recommended or published in this Service Manual and that you understand and have the
skills to carry out.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the product is properly grounded and to reduce the risk of fire,
electric shock, serious injury or death.
W006R1
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Section 1 Safety Information
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WARNING
Repairs that are made to your products by unqualified persons can result in hazards due to
improper assembly or adjustments subjecting you, or the inexperienced person making such
repairs, to the risk of serious injury, electrical shock or death.
W007
WARNING
If you or an unqualified person perform service on your product, you must assume the
responsibility for any personal injury or property damage which may result. The manufacturer
will not be responsible for any injury or property damage arising from improper service and/or
service procedures.
W008
NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to
cover all possible conditions and situations that may occur. Common sense, caution and care must be
exercised when installing, maintaining or operating the washer.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do
not understand.
Locating an Authorized Servicer
Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper
service. Review all service information before beginning repairs.
Warranty service must be performed by an authorized technician, using authorized factory parts. If service is
required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized
technician and using authorized factory parts.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 2
Introduction
Model Identification
Information in this manual is applicable to these washer models.
Model
Number
LWB19A*-1109
LWB19B*-1109
LWB19M*-1109
LWG74A*-3050
LWK24A*-3050
LWK74A*-3050
LWK23A*-3050
LWK73A*-3050
LWH18A*-3322
LWS01A*
LWS01A*C
LWS01A*-1000
LWS01A*-1088
LWS01A*-3088
LWS01A*-3300
LWS01B*
LWS01M*
LWS01M*-1000
LWS01M*-3088
LWS01M*-3300
LWS02A*
LWS02B*
LWS02M*
LWS11A*-3062
LWS16A*
LWS16A*K
LWS16B*
LWS16B*K
LWS16M*
LWS16A*-1000
LWS16M*-1000
LWS16A*-3000
1 Speed
Motor
2 Speed
Motor
X
X
X
X
3 Speed
Motor
Porcelain Washtub
(cu. ft.)
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Stainless Steel
Washtub (cu. ft.)
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
2.9
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
* Add Letter To Designate Color. L – Almond W – White
(continued)
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Section 2 Introduction
Model
Number
LWS16M*-3000
LWS16A*-3022
LWS16M*-3022
LWS16A*-3300
LWS16M*-3300
LWS16A*-3322
LWS16M*-3322
LWS16M*K
LWS17A*
LWS17A*K
LWS17B*
LWS17B*K
LWS17M*
LWS17A*-1000
LWS17M*-1000
LWS17A*-3000
LWS17M*-3000
LWS17A*-3022
LWS17M*-3022
LWS17A*-3028
LWS17A*-3050
LWS17M*-3050
LWS17A*-3300
LWS17M*-3300
LWS17A*-3322
LWS17M*-3322
LWS17A*B3020
LWS17M*B3020
LWS17A*B3069
LWS17M*B3069
LWS17M*K
LWS21A*-3062
LWS42M*-3050
LWS45A*
LWS45B*
LWS45M*
LWY17A*-1109
LWY17B*-1109
LWY17M*-1109
1 Speed
Motor
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
2 Speed
Motor
3 Speed
Motor
Porcelain Washtub
(cu. ft.)
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
X
X
X
X
X
X
X
Stainless Steel
Washtub (cu. ft.)
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
* Add Letter To Designate Color. L – Almond W – White
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 2 Introduction
Model
Number
LWY45A*-1109
LWY45B*-1109
LWY45M*-1109
LWZ01M*-1102
LWZ16A*-1000
LWZ16M*-1000
LWZ17A*-3000
LWZ17M*-3000
LWZ17A*B3020
LWZ17M*B3020
LWZ17A*B3069
LWZ17M*B3069
LWZ22M*-1102
LWZ42M*-1102
LWZ52M*-1102
LWZ77M*-1102
1 Speed
Motor
2 Speed
Motor
X
X
X
3 Speed
Motor
X
X
X
X
X
X
X
X
X
Porcelain Washtub
(cu. ft.)
Stainless Steel
Washtub (cu. ft.)
3.3
3.3
3.3
2.9
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
X
X
X
3.3
X
3.3
3.3
3.3
* Add Letter To Designate Color. L – Almond W – White
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Section 2 Introduction
How Your Washer Works
PRESSURE
SWITCH
TEMPERATURE
SWITCH
TIMER
MIXING
VALVE
AGITATOR
WASHTUB
OUTER
TUB
TRANSMISSION
MOTOR
PUMP
W407SE3A
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 2 Introduction
The cycle begins with a wash fill. The water
temperature is determined by the temperature selector.
While water fills the washtub, a column of air is
trapped in a pressure bulb and hose. The air pressure
continues to increase as the washtub fills with water
until it is great enough to activate the pressure switch.
The pressure switch then causes the wash fill to stop
and wash agitation to begin. However, the loading door
must be closed for the washer to agitate or spin.
The washer uses a reversing type motor, a special drive
belt and an idler assembly. The idler assembly applies
tension to the outside of the drive belt.
During agitation, the motor runs in the
counterclockwise direction. The spring tension on the
idler pulley applies the tension required to reduce the
slack on the drive belt and maintain maximum belt to
motor pulley contact. This eliminates belt slippage and
ensures an efficient wash action, even with extra large
loads.
The belt drives the transmission drive pulley in the
counterclockwise direction. The pulley drives the helix
which is splined to the input shaft of the transmission.
This causes the input shaft to turn inside of a roller
clutch which is pressed into the transmission cover.
This roller clutch acts as a bearing in the
counterclockwise direction allowing the transmission
gears to operate. The transmission’s rack and pinion
gear design produces a 210 degree agitation stroke at
the output shaft of the transmission which drives the
agitator. The brake assembly remains locked during the
agitation mode since no pressure is applied to it by the
transmission drive pulley.
As water is removed by the pump and the momentum
of the washtub increases, the idler spring tension
gradually overcomes the belt tension removing the belt
slack. This eventually increases the belt to pulley
contact until maximum spin speed is achieved.
The drive pulley turns clockwise riding up the ramps of
the helix, exerting pressure on the brake and forcing it
to release from brake pads. The helix drives the input
shaft of the transmission, and when the input shaft turns
in the clockwise direction the roller clutch locks onto
the shaft causing the entire transmission assembly to
turn. None of the gears in the transmission are
operating at this time. The hub of the washtub is splined
to the transmission tube and rotates with the
transmission assembly. The centrifugal force created
by the spinning washtub causes water to be extracted
from the clothes.
Water is introduced during the first spin to “SPRAY”
the garments and remove suds from them. The initial
spin is followed by rinse agitation to rinse away any
detergent residue. The washer fills and then agitates
like the wash portion of the cycle. Following rinse
agitation, a final spin extracts the rinse water from the
clothes preparing them for the dryer.
After the wash agitation is completed, the timer
advances into the first spin. During spin, the motor
reverses turning in the clockwise direction to spin the
water out of the washtub. The combination of water,
washtub and load weight cause the drive belt tension on
the idler side of the belt to overtake the idler spring
pressure allowing the belt to become slack on the
opposite side. This reduces the belt to pulley contact
and allows slipping between the belt and pulley.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Section 2 Introduction
Customer Service
If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
For technical assistance, call (920) 748-3121.
Nameplate Location
When calling or writing about your product, be sure to
mention model and serial numbers. Model and serial
numbers are located on nameplate(s) as shown.
W429SE1B
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 3
Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
IMPORTANT: Refer to Wiring Diagram for aid in testing washer components.
1. NO HOT WATER
POSSIBLE CAUSE
TO CORRECT
Hot water supply faucet is closed.
Water supply is cold.
Kinked hot water inlet hose.
Clogged mixing valve screen, or screen in outer end
of inlet hose nearest water supply faucet.
Inoperative hot water mixing valve solenoid.
Open faucet.
Check water heater.
Straighten or replace hose.
Disconnect hot water inlet hose, and clean or replace screen.
Inoperative timer.
Inoperative temperature switch.
Inoperative pressure switch.
Clogged pressure hose.
Broken, loose or incorrect wiring.
Test solenoid. Refer to Paragraph 50. Replace valve if
solenoid is inoperative.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Test switch. Refer to Paragraph 51. Replace if inoperative.
Test switch. Must have continuity from terminal 1 to 2 when
empty or 1-3 when full. Replace if inoperative.
Remove and clean or replace hose.
Refer to wiring diagram.
2. NO COLD WATER
POSSIBLE CAUSE
TO CORRECT
Cold water supply faucet is closed.
Kinked cold water inlet hose.
Clogged mixing valve screen, or clogged screens in
outer end of inlet hose nearest water supply faucet.
Inoperative cold water mixing valve solenoid.
Open faucet.
Straighten or replace hose.
Disconnect cold water inlet hose, and clean or replace
screen.
Test solenoid. Refer to Paragraph 50. Replace valve if
solenoid is inoperative.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Test switch. Refer to Paragraph 51. Replace if inoperative.
Test switch. Must have continuity from terminal 1 to 2 when
empty or 1-3 when full. Replace if inoperative.
Remove and clean or replace hose.
Refer to wiring diagram.
Inoperative timer.
Inoperative temperature switch.
Inoperative pressure switch.
Clogged pressure hose.
Broken, loose or incorrect wiring.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
3. NO WARM WATER
POSSIBLE CAUSE
TO CORRECT
No hot water.
No cold water.
Refer to Paragraph 1.
Refer to Paragraph 2.
4. WATER FILL DOES NOT STOP AT PROPER LEVEL
POSSIBLE CAUSE
TO CORRECT
Inoperative pressure switch.
Air leak in pressure hose.
Sediment on or under mixing valve diaphragm,
defective diaphragm, or armature binding in
armature guide.
Broken, weak or missing mixing valve armature
spring.
A siphoning action started in washer will cause
water to be siphoned from washer during cycle due
to end of drain hose being lower than cabinet top of
washer. Drain hose fits tight in standpipe or drain.
Water in pressure hose.
Broken, loose, shorted or incorrect wiring.
Test switch. Refer to Paragraph 47. Replace if inoperative.
Replace hose.
Replace valve.
12
Replace valve.
Install No. 562P3 Siphon Break Kit. Provide an air gap
around drain hose and drain receptacle. Install No. 36878
Standpipe Adapter (optional on some models).
Blow air through hose to remove water or replace hose.
Refer to wiring diagram.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
5. TIMER DOES NOT ADVANCE
POSSIBLE CAUSE
TO CORRECT
Timer is designed to pause during fill periods. Some Allow completion of fill period.
cycles have pauses (delicate cycles).
Inoperative timer.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Loading door is open.
Close loading door. Loading door MUST be closed any time
the washer is set to agitate or spin.
Washer will not fill.
Timer pauses until pressure switch is satisfied. Refer to
Paragraphs 1 and 2.
Timer motor lead wire is off timer terminal.
Refer to wiring diagram and reattach wire.
Broken, loose or incorrect wiring.
Refer to wiring diagram.
Make sure washer is not siphoning during rinse fill. Install siphon break kit, Part No. 562P3.
Timer is designed to pause when going from agitate Allow time for timer to go through that step. Refer to
to spin.
diagram for information on time required.
Timer is designed to stop if washer drive motor has Motor thermal protector reset time may vary depending
upon the reason for the washer overload, however, it should
been overloaded and motor thermal overload has
reset within 15 minutes. Check to ensure that washer was
tripped.
not overloaded with clothes.
Is circuit breaker to washer tripped, disconnecting Reset circuit breaker.
power to washer.
Washer will not fill.
Timer is designed to pause when going from spin into rinse
to allow the washtub to stop spinning before filling, make
sure that timer has advanced into fill portion of rinse cycle.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
6. MOTOR DOES NOT RUN
POSSIBLE CAUSE
TO CORRECT
Electrical power off, fuse blown or power cord not
plugged in.
Check laundry room for blown or loose fuse(s) or open
circuit breakers. (Washer itself does not have an electrical
fuse).
Close door or test switch and replace if inoperative.
Reset timer, or try another cycle.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Refer to Paragraph 49 to check start switch and start
windings.
Refer to Paragraph 49 to check switch and windings.
Wait two or three minutes for overload protector to reset. If
protector cycles repeatedly. Refer to Paragraph 9.
Remove belt and determine if motor shaft will spin. Replace
motor if shaft is locked up.
Replace pump.
Refer to wiring diagram.
Refer to wiring diagram for correct wiring.
Loading door not closed or inoperative switch.
Timer improperly set.
Inoperative timer.
Motor starting functions inoperative. No start; or
motor only hums.
Motor is dead, or will not run.
Motor overload protector has cycled.
Bind in upper or lower motor bearing.
Bind in pump (direct drive pump models).
Broken, loose or incorrect wiring.
Power cord is wired incorrectly.
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
7. NO AGITATION
POSSIBLE CAUSE
TO CORRECT
Timer is designed to pause (SOAK) during
DELICATE cycle. Allow completion of SOAK
period.
Motor will not run.
No Delicate cycle agitate.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Refer to Paragraph 49 to check switch and windings.
Refer to Paragraph 49 to check low speed switch and
windings.
Inoperative pressure switch.
Test switch. Must have continuity from terminal 1 to 3.
Replace if inoperative.
Broken, loose or incorrect wiring.
Refer to wiring diagram.
Loose or broken drive belt.
Replace belt.
Inoperative transmission assembly.
Repair or replace transmission assembly.
Sheared motor pulley roll pin. (Through Serial No. Remove drive motor and replace roll pin and any other
001113645)
damaged parts.
Motor overload protector has cycled.
Wait two or three minutes for overload protector to reset. If
protector cycles repeatedly. Refer to Paragraph 9.
Bind in pump.
Replace pump.
Loading door is open or door switch is inoperative. Close door or test switch and replace if inoperative.
8. CONSTANT AGITATION
POSSIBLE CAUSE
TO CORRECT
Inoperative timer.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Refer to wiring diagram.
Repair or replace transmission assembly.
Shorted or incorrect wiring.
Inoperative transmission assembly
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
9. WASHER OVERHEATS, CYCLES ON MOTOR THERMAL PROTECTOR, SWITCH ACTUATOR
KICKS IN AND OUT
POSSIBLE CAUSE
TO CORRECT
Belt is tacky and does not allow proper slip.
Belt tension is too great and does not allow proper
slip.
Inoperative timer.
Check belt and replace if defective.
Make sure idler spring is properly connected.
Motor switch functions inoperative.
Bind in water pump.
Brake pads or brake assembly binding.
Bearings, transmission or motor has locked up and
will not turn.
Incorrect voltage.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Refer to Paragraph 49 to check switch functions.
Replace pump.
Free binding pads, or replace pads and brake assembly.
Check that all these components are able to move freely.
Correct binding component.
Contact local utility company, or have a qualified electrician
check power supply.
10. SLOW SPIN OR NO SPIN
POSSIBLE CAUSE
TO CORRECT
Inoperative timer.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Close loading door, or test switch and replace if inoperative.
Loading door is open or door safety switch is
inoperative.
Bind in water pump.
Loose or broken drive belt.
Motor will not run.
Sheared motor pulley roll pin. (Through Serial No.
001113645)
Motor overload protector has cycled.
No clearance between brake pads and discs.
Broken, loose or incorrect wiring.
Inoperative transmission assembly.
Oil on belt.
16
Replace pump.
Replace belt.
Refer to Paragraph 49 to check switch and windings.
Remove drive motor and appropriately replace roll pin and
any other damaged parts.
Wait two or three minutes for overload protector to reset. If
protector cycles repeatedly, refer to Paragraph 9.
Replace pads and brake assembly.
Refer to wiring diagram.
Repair or replace the transmission assembly.
Replace belt.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
11. CONSTANT SPIN
POSSIBLE CAUSE
TO CORRECT
Inoperative timer.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Replace brake pads and brake assembly.
Washtub does not stop spinning within seven
seconds after loading door is opened.
Excessive wear on brake pads, or missing brake
pads.
Shorted or incorrect wiring.
Inoperative lid switch.
Replace brake pads and brake assembly.
Refer to wiring diagram.
Replace lid switch.
12. WASHER STOPS IN CYCLE; QUITS AFTER A COUPLE LOADS; IS INTERMITTENT
POSSIBLE CAUSE
TO CORRECT
Belt is tacky and does not allow proper slip.
Belt tension is too great and does not allow proper
slip.
Inoperative timer.
Check belt and replace if defective.
Make sure idler spring is properly connected.
Test for continuity through timer circuits. Refer to wiring
diagram. Replace if inoperative.
Broken, loose or incorrect wiring.
Refer to wiring diagram.
Motor overload protector has cycled.
Wait two or three minutes for overload protector to reset. If
protector cycles repeatedly. Refer to Paragraph 9.
Motor switch functions inoperative.
Refer to Paragraph 49 to check switch functions.
Brake, transmission or motor has locked up and will Check that all these components are able to move freely.
not turn.
13. WASHER IS LOCKED UP OR BINDING
POSSIBLE CAUSE
TO CORRECT
Excessive belt tension.
Bind in upper or lower bearing.
Bind in water pump.
Bind in transmission.
Brake pads binding.
Incorrect voltage.
Replace belt and/or idler spring.
Replace bearing.
Replace pump.
Repair or replace transmission.
Free binding pads, or replace pads.
Contact local utility company, or have a qualified electrician
check power supply.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
14. OUTER TUB DOES NOT EMPTY
POSSIBLE CAUSE
TO CORRECT
Kinked drain hose.
Drain hose out of hose retainer clip in back of
cabinet.
Inoperative water pump.
Obstruction in outer tub outlet hose.
Straighten hose.
Remove washer front panel and install drain hose into hose
retainer clip in back of cabinet.
Replace pump.
Remove obstruction.
15. EXCESSIVE VIBRATION
POSSIBLE CAUSE
TO CORRECT
Washer is not properly leveled.
Unbalanced load in tub.
Broken or disconnected centering spring(s).
Washer is installed on weak, “spongy”, carpeted or
built-up floor.
Incorrect or loose cabinet screws.
Base damaged (washer was dropped).
Lubricant on pivot dome and/or base friction ring.
Partial liquid filled balance ring leaking.
Broken friction ring.
Adjust leveling legs.
Stop washer, redistribute load, then restart washer.
Connect or replace centering spring(s).
Relocate washer, or support floor to eliminate weak or
“spongy” condition.
Replace with correct screws or tighten.
Replace base assembly.
Remove lubricant or replace parts.
Replace balance ring.
Replace friction ring.
16. WATER LEAKING FROM OUTER TUB
POSSIBLE CAUSE
TO CORRECT
Leaking water seal in outer tub.
Hole in outer tub.
Pressure hose or accumulator leaking.
Tub cover gasket leaking.
Obstruction in drain causing water to come over top
of outer drain tub cover.
Tub-to-pump hose leaking at clamp.
Replace hub and seal kit assembly. Refer to Paragraph 39.
Replace outer tub.
Replace pressure hose and/or accumulator.
Replace gasket.
Remove obstruction.
18
Tighten clamp.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 4
Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
17. WALL RECEPTACLE POLARITY CHECK
(Refer to Figure 1)
GROUND
NEUTRAL
L1
NOTE: Have a qualified
electrician check polarity of
wall receptacle. If a voltage
reading is measured other
than that illustrated, the
qualified electrician should
correct the problem.
NEUTRAL
SIDE
115±12
V.A.C.
ROUND
GROUNDING
PRONG
0
V.A.C.
115±12
V.A.C.
W011GE3A
230 VOLTS
50 HZ
POWER CORD
(Fused with
13 AMP Fuse)
0 VOLTS
NOTE: Have a
qualified electrician
check polarity of wall
receptacle. If a voltage
reading is measured
other than that
illustrated, the
qualified electrician
should correct the
problem.
230 VOLTS
50 HZ
W355SE3A
Figure 1
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Section 4 Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
18. POWER CORD TO CONNECTION BLOCK, CONNECTION BLOCK TO CONTROL HOOD REAR
PANEL; MODELS WITH SUFFIXES B3069, 3050 AND 3062
(Refer to Figure 2)
CONNECTION
BLOCK COVER
CONNECTION
BLOCK
CONTROL HOOD
REAR PANEL
WIRE
HARNESS
BLUE
WIRE
BROWN
WIRE
L1
N
(L2)
GREEN/
YELLOW
WIRE
STRAIN RELIEF
(Open position)
POWER
CORD
POWER
CORD
L1
N
(L2)
STRAIN
RELIEF
(Closed
position)
W411PE3B
Figure 2
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 4 Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
19. POWER CORD TO CABINET TOP, CABINET TOP TO CONTROL HOOD MOUNTING
BRACKET, PRESSURE SWITCH MOUNTING BRACKET AND GROUND TAB ON GRAPHIC
PANEL
(See Figure 3)
GROUND
WIRES
POWER
CORD
GROUND
WIRES
GROUND
WIRES
W505SE3B
POWER CORD TO CONTROL HOOD REAR PANEL, CONTROL HOOD REAR PANEL TO
CONTROL HOOD MOUNTING BRACKET, PRESSURE SWITCH MOUNTING BRACKET AND
GROUND TAB ON GRAPHIC PANEL
SCREW
HOOD HARNESS
EARTH (Ground)
WIRE
NUT
NUT
WASHER
POWER CORD EARTH
(Ground) WIRE
EARTH
(Ground)
WIRES
CONTROL
HOOD REAR
PANEL
W356SE3B
Figure 3
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Section 4 Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
20. CONTROL HOOD WIRE HARNESS TO TOP LEFT REAR CORNER GUSSET OF CABINET
(Refer to Figure 4)
CORNER
GUSSET
GROUND
WIRES
GROUND
SCREW
W426SE2A
Figure 4
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 4 Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
21. WIRE HARNESS TO MOTOR
(Refer to Figures 5 and 6)
WIRE HARNESS
CONNECTION
BLOCK
GROUNDING
TERMINAL
GROUND
WIRE
TLW1227G
Figure 5
Models with suffixes ending 3050
GROUND
WIRES
WIRE
HARNESS
CONNECTION
BLOCK
W329SE3B
Figure 6
All other Models
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Section 4 Grounding
Notes
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5
Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
IMPORTANT: When reference is made to
directions (right or left) in this manual, it is from
operator’s position facing front of washer.
d. Disconnect wires from component parts and
carefully remove components from hood
assembly.
NOTE: Refer to wiring diagram when rewiring
component parts.
22. CONTROL HOOD ASSEMBLY
a. Remove three screws holding rear of hood
assembly to control hood rear panel.
Refer to Figure 7.
b. Pivot hood assembly forward on cabinet top.
Refer to Figure 7.
c. Carefully remove bottom front of hood from
clips on cabinet top.
TO REMOVE CONTROL HOOD END
PANELS
Remove four screws holding end panels to control
mounting plate. Refer to Figures 8, 9, 10 or 11.
PIVOT
HOOD
FORWARD
HOOD
ATTACHING
SCREWS
W252IE1A
W169SE3B
Figure 7
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Section 5 Service Procedures
TOP
COVER
SCREWS
SCREW
PRESSURE
SWITCH
END CAP
(Left)
SCREW
LOCKWASHER
SCREW
SWITCH
ASSEMBLY
TEMPERATURE
SWITCH
CONTROL
KNOBS
SCREW
SCREW
TIMER
INDICATOR
LIGHT
SWITCH
COLLAR
KNURLED
NUT
TIMER
KNOB
TIMER
KNOB
SKIRT
SCREW
CONTROL
MOUNTING
PLATE
GRAPHIC
PANEL
END CAP
(Right)
SUPPORT
SCREW
TERMINAL
BLOCK
SCREW
LID LOCK
CONTROL
LOCKWASHERS
SCREW
STRAIN
RELIEF
NUT
SCREW
STICKER
HOLD-DOWN
CLIP
CONTROL
HOOD REAR
PANEL
LOCKWASHER
NUT
CABINET TOP
W371PE3C
Figure 8
GRAPHIC PANEL, CONTROL MOUNTING PLATE AND CONTROLS
(Models LWS17A*B3069, LWZ17A*B3069, LWS17M*B3069 and LWZ17M*B3069
through Serial No. 00061999)
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
TOP
COVER
SCREWS
TEMPERATURE
SWITCH
PRESSURE
SWITCH
SCREWS
END CAP
(Left)
SCREW
TIMER
SCREW
CONTROL
KNOB
END CAP
(Right)
INDICATOR
LIGHT
SWITCH
ASSEMBLY
TIMER
KNOB
SUPPORT
CONTROL
MOUNTING
PLATE
SCREW
GRAPHIC
PANEL
TIMER KNOB
SKIRT
HOLD-DOWN
CLIP
SCREW
CONNECTION
BLOCK
SCREW
STICKER
WIRE
HARNESS
LID LOCK
CONTROL
POWER
CORD
NUTS
LOCKWASHERS
CONTROL
HOOD
REAR PANEL
Figure 9
GRAPHIC PANEL, CONTROL MOUNTING PLATE AND CONTROLS
(Models LWS17A*B3069, LWZ17A*B3069, LWS17M*B3069 and LWZ17M*B3069
starting Serial No. 00062000)
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Section 5 Service Procedures
TOP
COVER
SCREWS
TEMPERATURE
SWITCH
SCREW
PRESSURE
SWITCH
SCREW
END CAP
(Left)
OPTION
SWITCH
SCREWS
TIMER
SCREW
SCREW
GROUND
CLIP
END CAP
(Right)
CONTROL
KNOBS
CONTROL
MOUNTING
PLATE
GRAPHIC
PANEL
TIMER
KNOB
TIMER KNOB
SKIRT
SCREW
SCREW
CONTROL
HOOD
REAR PANEL
STICKER
WIRE
HARNESS
HOLD-DOWN
CLIP
CONNECTION
BLOCK
POWER
CORD
TLW791P
Figure 10
GRAPHIC PANEL, CONTROL MOUNTING PLATE AND CONTROLS
(Models with suffixes 3050 and 3062)
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
SCREWS
TOP
COVER
PRESSURE
SWITCH
END CAP
(Left)
SCREW
SCREW
TEMPERATURE
SWITCH
TIMER
SCREW
SCREW
CONTROL
KNOB
SCREW
GROUND
CLIP
CONTROL
MOUNTING
PLATE
TIMER
KNOB
SCREW
TIMER
KNOB
SKIRT
END CAP
(Right)
SCREW
GRAPHIC
PANEL
CABINET
TOP
HOLD-DOWN
CLIP
SCREW
CONTROL
HOOD REAR
PANEL
W320PE3E
Figure 11
GRAPHIC PANEL, CONTROL MOUNTING PLATE AND CONTROLS
(All Other Models)
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
e. Remove two screws holding timer to control
hood mounting plate. Refer to Figure 12.
23. TIMER
a. Unscrew timer knob from timer shaft (right
hand thread), then remove timer knob skirt.
b. Remove three screws holding rear of hood
assembly to control hood rear panel.
Refer to Figure 7.
c. Pivot hood assembly forward on cabinet top.
Refer to Figure 7.
d. Refer to Figures 8, 9, 10 or 11 for timer
removal.
NOTE: DO NOT attempt to repair timer.
f. Disengage wire harness terminal block plugs
from timer by pressing in on movable locking
tabs (located on each side of terminal block
plug) and pulling away from timer. Refer to
Figure 12.
LOCKING TAB
CONTROL
HOOD
ASSEMBLY
TIMER
TERMINAL
BLOCK
PLUG
TIMER
ATTACHING
SCREWS
W427SE3A
Figure 12
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
g. Seat horizontal and vertical tabs on front plate
of timer completely into slots on control
mounting plate. Refer to Figure 13.
h. Tighten attaching screws between 12 to 18 inch
pounds (1.6 to 2.4 Nm).
IMPORTANT: To avoid an open circuit, DO NOT
pull on terminal block wires when removing blocks
from timer as this could damage wires or terminal
crimping.
IMPORTANT: Before attaching wire harness
terminal blocks to timer, make sure all male
terminals on timer are straight and are capable of
accepting terminals from wire harness terminal
blocks.
IMPORTANT: To avoid timer damage, do not allow
timer to be struck on corners, edges of frame, or on
timer shaft.
NOTE: When installing timer, make sure timer is
installed correctly and is securely mounted to
control mounting plate. Refer to Figure 13.
TIMER
TIMER
ATTACHING
SCREWS
CONTROL
MOUNTING PLATE
W428SE3A
SLOTS
TABS
Figure 13
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
24. TEMPERATURE SWITCH
a. Remove three screws holding rear of hood
assembly to control hood rear panel.
Refer to Figure 7.
b. Pivot hood assembly forward on cabinet top.
Refer to Figure 7.
c. Disconnect wires from switch terminals.
LOCKING TABS
(Press in on tabs and
at same time turn
switch 1/4 turn
counterclockwise
to remove
switch)
NOTE: Refer to wiring diagram when rewiring
switch.
d. Press in on two locking tabs and at the same
time turn the switch 1/4 turn counterclockwise
to remove switch from control hood mounting
plate. Refer to Figure 14.
TEMPERATURE
SWITCH
CONTROL HOOD
MOUNTING
PLATE
IMPORTANT: Before removing switch, note the
switch position in relation to control hood mounting
plate so switch can be reinstalled in same position.
NOTE: When installing switch, place switch tabs
into cutout in mounting plate and turn switch
clockwise to its full limit of travel, within the
mounting plate opening, until both locking tabs
snap into place.
25. PRESSURE SWITCH
a. Remove three screws holding rear of hood
assembly to control hood rear panel.
Refer to Figure 7.
b. Pivot hood assembly forward on cabinet top.
Refer to Figure 7.
c. Disconnect wires from pressure switch.
d. Refer to Figures 8, 9, 10 or 11 for switch
removal.
NOTE: Refer to wiring diagram when rewiring
switch.
IMPORTANT: Before connecting hose to pressure
switch, blow air through pressure hose to remove
any condensation that may have accumulated in the
hose.
26. GRAPHIC PANEL
a. Unscrew timer knob from timer shaft (right
hand thread), then remove timer knob skirt.
32
W513SE1A
Figure 14
b. Pull knob off switch shaft.
c. Remove three screws holding rear of hood
assembly to control hood rear panel.
Refer to Figure 7.
d. Pivot hood assembly forward on cabinet top.
Refer to Figure 7.
e. Disconnect wires from component parts and
carefully remove components from control
hood assembly.
NOTE: Refer to wiring diagram when rewiring
component parts.
f. Bend tabs on graphic panel (located inside of
control hood) straight out toward rear of hood.
Refer to Figures 8, 9, 10 or 11.
g. Carefully remove graphic panel off front of
control mounting plate.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
27. LOADING DOOR
a. Open loading door. Refer to Figure 15.
b. Remove two screws holding left hinge to door
and remove hinge. Refer to Figure 15.
c. Raise loading door to a nearly vertical position,
to disengage loading door from loading door
clip, swing left side of door toward front of
washer. Refer to Figure 16, procedure one.
d. Rotate loading door so door is upside down.
Refer to Figure 16, procedure two.
e. Carefully remove loading door, right hinge and
bushing from cabinet top. Refer to Figure 16,
procedure three.
Procedure One
DOOR
FRONT
NOTE: Reverse procedure when installing door.
Procedure Two
LOADING
DOOR
DOOR
FRONT
HINGE
ATTACHING
SCREWS
HINGE
ATTACHING
SCREWS
Procedure DOOR
Three
FRONT
HINGE
(Right)
HINGE
(Left)
W429SE1A
Figure 15
W430SE1A
Figure 16
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
28. AGITATOR
a. Open loading door.
b. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 17.
IMPORTANT: Hooks should be positioned 180
degrees from each other, and must be placed under
base of agitator near agitator vane for greater
stability. If hooks are placed between the vane area,
agitator damage may occur.
c. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
NO. 254P4P
AGITATOR
HOOKS
29. AGITATOR, DRIVE BELL AND SEAL
ASSEMBLY
IMPORTANT: If water is present in washtub, spin
and pump out before attempting to remove drive
bell.
a. Remove agitator, Paragraph 28.
b. Remove plug, screw (and “O” ring if present)
from top of drive bell.
NOTE: Use No. 294P4 Drive Bell Tool to remove
drive bell from transmission shaft.
NOTE: Drive Bell Tool, No. 253P4, must be
updated with Jaws, No. 294P4A, and Bolt, No.
294P4B, to remove the 36443P Drive Bell.
c. Back bolt out of 294P4 Drive Bell Tool
approximately three quarters of the way.
Refer to Figure 18.
d. Place tool over drive bell, making sure indent
on jaws line up with wide slots on drive bell.
Refer to Figure 19.
BOLT
LARGE
NUT
INDENT
WING
NUT
JAWS
W431SE1A
JAW
LIP
L021IE1A
AGITATOR
Figure 18
Figure 17
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
JAW
e. Thread bolt down through hole in top of drive
bell until it bottoms out.
f. Place lip of each jaw under bottom edge of
drive bell, making sure indent on jaws line up
with wide slots on drive bell. Tighten wing nuts
on tool to hold jaws firmly against drive bell.
Refer to Figure 19.
g. Using an adjustable wrench, turn large nut on
tool COUNTERCLOCKWISE to pull drive
bell from transmission output shaft. Refer to
Figure 20.
WING
NUTS
JAW
DRIVE
BELL
WIDE
SLOT
W298SE1A
IMPORTANT: If large nut is turned clockwise
when pulling drive bell, you will twist off the
quarter inch bolt.
h. After drive bell has been pulled, remove tool
and drive bell by turning quarter inch bolt out of
transmission output shaft.
Figure 19
TURN ADJUSTABLE WRENCH
COUNTERCLOCKWISE
TO REMOVE DRIVE BELL
W293SE1A
Figure 20
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
i. Loosen wing nuts and remove drive bell from
tool.
j. Remove old seal from hub assembly by:
(1) Placing a flat bladed screwdriver between
bottom edge of seal and hub.
(2) Using washtub bolts as a pry area, pop off
lower seal bead.
(3) Grasping bottom of seal pull straight up
freeing upper seal bead.
HEX
NUT
APPLY GREASE TO
INSIDE SEALING LIPS
HUB
ASSEMBLY
TRANSMISSION
OUTPUT SHAFT
SEAL
TRANSMISSION
OUTPUT SHAFT
HUB
ASSEMBLY
W421SE1A
WASHER
Figure 22
n. Apply remainder of supplied grease, No.
36765P, to exposed surface of washer between
transmission output shaft and seal. Refer to
Figure 24.
o. Place new drive bell seal onto hub and carefully
push into position using large end of No. 293P4
Seal Tool. Refer to Figure 23.
BRONZE
BEARING
HUB SHOULDER
W499SE1A
Figure 21
k. Thoroughly clean all foreign material from seal
mounting area of hub assembly, bronze bearing
and washer. Refer to Figure 21.
l. Lubricate new seal with liquid soap or soapy
water to aid in assembly of seal onto hub.
Refer to Figure 22.
m. Apply a small amount of supplied grease,
No. 36765P, to inside sealing lips of seal. Refer
to Figure 22.
IMPORTANT: Using a small pocket mirror, check
entire circumference of bottom seal flange to make
sure seal is pressed down against shoulder on hub;
there should be no gap!
p. Turn the No. 293P4 Seal Tool upside-down and
place the small end over transmission output
shaft and onto the seal. Refer to Figure 24.
q. Push down on tool with a quick motion until it
bottoms out and the top of seal is fully seated.
Refer to Figure 24.
IMPORTANT: DO NOT allow any lubricants to
come in contact with outside surface of seal.
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
293P4
SEAL TOOL
HUB
ASSEMBLY
INSTALLING DRIVE BELL
a. Position new drive bell over transmission
output shaft. Rotate drive bell until splines in
drive bell line up with splines on transmission
output shaft.
b. Place No. 294P4 Bell Tool over top of drive
bell. Screw bolt into transmission output shaft
until it bottoms out.
NOTE: It is not necessary to clamp tool jaws on
drive bell during this operation.
W422SE1A
Figure 23
293P4
SEAL
TOOL
HUB
SHOULDER
TOP OF
SEAL
c. Using an adjustable wrench, turn large nut on
tool CLOCKWISE to force drive bell down
onto transmission shaft until drive bell bottoms
out on shaft.
d. Turn quarter inch bolt out of transmission shaft
and remove tool.
e. Thread new shoulder screw down through hole
in top of drive bell and into transmission shaft.
NOTE: Tighten new shoulder screw to
approximately 60 to 80 inch-pounds
(6.86 to 9.15 Nm).
f. Place new plug over hole in drive bell and
firmly press into place using palm of your hand.
HUB
ASSEMBLY
APPLY
36765P
GREASE
(Step n)
BOTTOM
SEAL FLANGE
W423SE1A
Figure 24
NOTE: It may be necessary to insert the end of a
paper clip along side of plug as it is pressed into
drive bell to release entrapped air.
IMPORTANT: When fully seated plug should not
extend above drive bell more than 1/8 inch (3.2 mm).
g. Place agitator on top of drive bell. Slowly rotate
agitator until fingers on underside of agitator
line up with large slots on drive bell.
h. A sharp blow on top of agitator, with palm of
your hand, will force agitator down onto drive
bell, allowing fingers on underside of agitator
to lock under bottom edge of drive bell.
NOTE: Do not push agitator onto drive bell any
further than necessary.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
30. FRONT PANEL
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (approximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time pull
top edge of front panel away from front of
washer. Repeat for opposite side.
CABINET TOP
HOLD-DOWN
SCREWS
c. Lift front panel off two screws and set panel
aside.
PANEL LOCATORS
Remove screws holding panel locators to side
flanges of front panel.
BRACE
Remove screws holding brace to side flanges of
front panel. Remove brace from front panel by
swinging one end toward bottom of front panel
and remove brace.
SPRING
CLIP
FRONT
PANEL SCREWS
PUTTY
KNIFE
W432SE3A
Figure 25
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
e. Unhook idler spring from clip on front of motor
mounting bracket. Refer to Figure 26.
31. MOTOR AND MOUNTING BRACKET
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
IMPORTANT: Use care when releasing idler lever
tension. If idler spring is overstretched, washer
operation will be affected.
f. Reach in and around right side of motor and run
belt off right side of large drive pulley. Refer to
Figure 26.
g. Disconnect wire harness from motor switch by
pressing down on locking tab on top of
connection block and at the same time pull
connection block away from motor switch.
Refer to Figure 26.
h. Remove four screws holding motor and
mounting bracket to lower outer tub flange and
to weldment assembly. Refer to Figure 26.
Then lift complete assembly out of washer.
a. Insert putty knife between cabinet top and top
edge of front panel (approximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Life front panel off two screws and set panel
aside.
IMPORTANT: There will always be some water
that will remain in outer tub, therefore, before
removing hoses from pump, hoses must be pinched
off or drained to prevent water spillage.
d. Direct Drive Pump Models — Loosen
hose clamps and remove hoses from pump
assembly. Refer to Figure 26.
IMPORTANT: Carefully lay motor on its side.
Observe belt configuration around rear pump leg.
Belt MUST encircle rear pump leg when
reassembling. Refer to Figure 26.
MOTOR
MOUNT ATTACHING
SCREWS
SWITCH
ATTACHING
SCREW
LOCKING
TAB
BELT
PUMP HOSES
CONNECTION
BLOCK
MOTOR
SWITCH
IDLER
SPRING
TAB
W433SE3E
Figure 26
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Section 5 Service Procedures
Direct Drive
Pump Models
PUMP MOUNTING
SCREWS
REAR
PUMP LEG
(Must be located
between belt when
installing pump
assembly)
PUMP
ASSEMBLY
PUMP
LEGS
MOTOR SHAFT
(Clean shaft and apply
a thin film of lubricant,
No. 03200)
MOTOR
EMBOSSES
MOTOR
EMBOSS
MOTOR
ASSEMBLY
Electric
Pump Models
SCREW
SHIELD
ELECTRIC
DRAIN PUMP
SOUND
ISOLATOR
MOUNTING
BRACKET
SCREW
W498SE3B
Figure 27
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
PUMP AND BELT REMOVAL—(Direct
Drive Pump Models)
a. Remove three screws holding pump assembly
to motor. Refer to Figure 27.
REASSEMBLY OF PUMP AND BELT
IMPORTANT: Install pump and belt together.
Drive belt MUST be replaced with special clutchtype belt for proper washer operation. Refer to
parts manual for correct part number of belt.
a. Clean any corrosion or foreign material from
motor shaft that will be contacting the double
“D” slot in pump impeller.
b. Apply a thin film of No. 03200 Lubricant to end
and sides of motor shaft. This lubricant helps
keep moisture out of the hub area and retards
corrosion.
c. Align pump impeller hub with motor shaft.
Make sure belt encircles rear pump leg,
carefully push pump onto motor shaft so three
pump legs bottom out in the embosses on motor
housing before screws are tightened. Refer to
Figure 27.
d. Tighten three screws to 35 inch-pounds
(4.0 Nm) maximum. DO NOT overtighten
screws!
e. Reinstall motor and pump assembly into
washer.
MOTOR REMOVAL
Remove nuts, steel washers, spacers and rubber
mounts holding motor to mounting bracket.
Refer to Figure 28. Lift motor off mounting
bracket and remove balance of rubber mounts and
steel washers from motor mounting studs.
IMPORTANT: When installing motor on mounting
bracket, position motor with switch facing toward
left side of mounting bracket.
NOTE: Refer to Figure 28 for motor and mounting
bracket assembly sequence.
IMPORTANT: After installing motor and pump
assembly in washer and all hoses have been
reconnected, add at least a quart of water to
washtub to lubricate pump seals. Running a pump
without water will ruin the seals.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Section 5 Service Procedures
SCREW
MOTOR
SHIELD
MOTOR
ASSEMBLY
MOTOR
SWITCH
ROLL PIN
(Through
Serial No. 001113645)
SHIELD
(Models with Suffixes
B3020 or B3069)
MOTOR
PULLEY
MOTOR
MOUNT
POST
MOTOR
MOUNTING
BRACKET
MOTOR
MOUNT
LOCKNUT
WASHER
LOCKNUT
SCREW
IDLER
LEVER
SCREW
CLAMP
WASHER
CAPACITOR
(Model LWZ77M*-1102)
SHOULDER
BOLT
MOTOR
MOUNT
IDLER
SHAFT
MOTOR
MOUNT
POST
LOCKNUT
WASHERS
BELT
(Agitate and
Spin)
IDLER
PULLEY
PUMP ASSEMBLY
(Direct Drive
Pump Models)
RETAINER
RING
SCREW
(Direct Drive
Pump Models)
TLW1035P
Figure 28
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
32. IDLER LEVER AND PULLEY
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (approximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
IMPORTANT: There will always be some water
that will remain in outer tub, therefore, before
removing hoses from pump, hoses must be pinched
off or drained to prevent water spillage.
d. Direct Drive Pump Models — Loosen
hose clamps and remove hoses from pump
assembly. Refer to Figure 26.
e. Unhook idler spring from idler lever. Refer to
Figure 26.
IMPORTANT: Use care when removing idler
spring. If idler spring is overstretched, washer
operation will be affected.
39311
f. Reach in and around right side of motor and run
belt off right side of large drive pulley. Refer to
Figure 26.
g. Disconnect wire harness from motor switch by
pressing down on locking tab on top of
connection block and at the same time pull
connection block away from motor switch.
Refer to Figure 26.
h. Remove four screws holding motor mounting
bracket to lower flange of outer tub and to
weldment assembly. Refer to Figure 26. Then
remove complete assembly out of washer.
NOTE: For ease of idler lever removal, remove
pump assembly from motor, then remove motor
from mounting bracket.
i. Remove locknut, washer and shoulder bolt
holding idler lever and pulley to motor
mounting bracket. Refer to Figure 28.
NOTE: Refer to Figure 28 for idler lever and pulley
assembly sequence.
j. Apply a light film of No. 03200 Lubricant to
area of idler lever that makes contact with
motor mounting bracket.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
33. MOTOR SWITCH
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (approximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
d. Remove two screws holding motor shield to
motor. Refer to Figure 26.
44
e. Disconnect wire harness from motor switch by
pressing down on locking tab on top of
connection block and at the same time pull
connection block away from motor switch.
Refer to Figure 26.
IMPORTANT: To avoid an open circuit, DO NOT
pull on terminal block wires when removing block
from motor switch as this could damage wires or
connection crimpings. Before attaching wire
harness connection block to motor switch, make
sure all male terminals on motor switch are straight
and are capable of accepting terminals from wire
harness connection block.
f. Remove screw holding motor switch to motor.
Refer to Figure 26.
g. Disconnect internal motor leads from motor
switch terminals. Then remove switch.
NOTE: Refer to Wiring Schematics, SECTION 9
for rewiring internal motor switch wires.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
d. Remove two screws holding pump assembly to
washer base. Refer to Figure 29.
e. Disconnect pump wire harness from base wire
harness at quick disconnect blocks. Refer to
Figure 29.
f. Pull pump out of washer as far as hoses permit.
34. PUMP ASSEMBLY (Electric Pump Models)
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (approximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
IMPORTANT: There will always be some water
that will remain in outer tub, therefore, before
removing hoses from pump, hoses must be pinched
off or drained to prevent water spillage.
g. Loosen hose clamps and remove hoses from
pump.
NOTE: Refer to Figure 30 for assembly sequence.
MOTOR
SHIELD
MOTOR
SHIELD
ATTACHING
SCREW
HOSE
CLAMP
DRAIN
HOSE
WIRE
HARNESS
DRAIN HOSE
SUPPORT
WIRE HARNESS
CLIP
HEX HEAD
SCREW
WASHER
BASE
MOTOR AND PUMP
ATTACHING SCREWS
TUB-TO-PUMP
HOSE
W512SE3A
Figure 29
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Section 5 Service Procedures
SIPHON BREAK
KIT
DRAIN HOSE
ELBOW
OUTER
TUB
SCREW
HOSE
CLAMP
HOSE
RETAINER CLIP
TUB-TO-PUMP
HOSE
HOSE
COUPLER
HOSE
CLAMP
DRAIN
HOSE
PUMP-TO-ELBOW
HOSE
SHIELD
HOSE
CLAMP
SCREW
HOSE
SUPPORT
SOUND
INSULATOR
ELECTRIC
PUMP ASSEMBLY
SCREW
SCREW
MOUNTING
BRACKET
W377PE3A
Figure 30
46
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
35. CABINET TOP ASSEMBLY
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
d. Remove two cabinet top hold-down screws.
Refer to Figure 25.
e. If area or space permits, tape loading door
closed and lift cabinet top to a vertical position
by hinging it on the rear hold-down hinges.
NOTE: Cabinet top is self-supporting, however, a
small chain may be used for additional support.
Refer to Figure 31.
TO REMOVE CABINET TOP FROM
WASHER
a. Repeat previous steps “a” through “d”.
b. Remove three screws holding rear of hood
assembly to control hood rear panel. See
Figure 7. Pivot hood assembly forward on
cabinet top. Refer to Figure 7.
c. Loosen hose clamp and remove pressure hose
from pressure bulb.
d. Then remove pressure hose from clips located
on mixing valve cabinet flange and the top
flange at rear of cabinet. Refer to Figure 33.
e. Disconnect wire harness at disconnect blocks.
f. Tape loading door closed.
g. Lift front of cabinet top slightly and pull
forward to disengage from rear hold-down
brackets.
h. Pull top forward far enough to permit
disconnecting earth (ground) wires from top
left rear corner gusset of washer cabinet. Refer
to Figure 33.
i. Disconnect wires from mixing valve solenoids
at quick disconnect blocks. Refer to Figure 33.
IMPORTANT: Refer to wiring diagram when
rewiring mixing valve solenoids.
j. Carefully lift cabinet top off washer and set
alongside the washer cabinet on protective
padding.
IMPORTANT: DO NOT lay cabinet top flat because
it will damage door switch lever.
DOOR
SWITCH
LEVER
CHAIN
W435SE1B
Figure 31
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
36. DOOR SWITCH
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
d. Remove two cabinet top hold-down screws.
Refer to Figure 25.
e. If area or space permits, tape loading door
closed and lift cabinet top to a vertical position
by hinging it on the rear hold-down hinges.
NOTE: Cabinet top is self-supporting, however, a
small chain may be used for additional support.
Refer to Figure 31.
f. Remove screw holding door switch assembly to
underside of cabinet top. Refer to Figure 32.
g. Disconnect wires from door switch.
NOTE: Refer to wiring diagram when rewiring
switch.
h. Remove two screws holding switch to switch
holder. Refer to Figure 32.
i. Remove switch from switch holder.
DOOR
SWITCH
SCREW
SWITCH
HOLDER
SWITCH
ASSEMBLY ATTACHING
SCREW
W438SE1A
Figure 32
48
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
d. Remove two cabinet top hold-down screws.
Refer to Figure 25.
e. If area or space permits, tape loading door
closed and lift cabinet top to a vertical position
by hinging it on the rear hold-down hinges.
NOTE: Cabinet top is self-supporting, however, a
small chain may be used for additional support.
Refer to Figure 32.
f. Remove screw(s) holding mixing valve to
mounting bracket at rear of washer cabinet.
Refer to Figure 33.
NOTE: When installing mixing valve, tab on
bottom flange must be placed in positioning hole in
mounting bracket.
39311
g. Pull mixing valve out toward front of washer
far enough to permit disconnecting water inlet
and fill hoses from mixing valve. Refer to
Figure 33.
h. Remove wires and quick disconnect blocks
from mixing valve solenoid terminals. Refer to
Figure 33.
NOTE: Refer to wiring diagram when rewiring
solenoids.
EARTH
(Ground)
SCREW
PRESSURE
HOSE
CLIPS
MIXING
VALVE
ATTACHING
SCREWS
FILLER
HOSE
C
37. MIXING VALVE ASSEMBLY
H
HOSE
CLAMP
WIRE
HARNESS
DISCONNECT
TERMINALS
PRESSURE
HOSE
PRESSURE
BULB
MIXING
VALVE
W440SE1C
Figure 33
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
HOSE
CLAMP
FILLER
HOSE
OUTER
TUB COVER
HOLD-DOWN
TABS
W441SE3B
Figure 34
38. WASHTUB AND BALANCE RING
a. Open loading door.
b. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 17.
IMPORTANT: Hooks should be positioned 180
degrees from each other, and must be placed under
agitator vane for greater stability. If hooks are
placed between vane area, agitator damage may
occur.
50
c. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
d. Hinge cabinet top or remove, Paragraph 35.
e. Loosen hose clamp and remove filler hose from
outer tub cover. Refer to Figure 34.
NOTE: When installing filler hose, white line on
hose must point toward front of washer. Refer to
Figure 34.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
f. There are eight tub cover hold-down tabs which
snap over outer tub flange. Place your fingers
under the flap of the hold-down tab of the tub
cover and pull out on flap and at the same time
lift upward on cover to unsnap hold-down tabs
from outer tub flange. One by one, disengage
each of the eight hold-down tabs from outer tub
flange and remove cover.
i. Install gasket past ends of hold-down tabs to
bottom of gasket groove using semi-circled end
of tool Part No. 273P4. Refer to Figure 35.
NOTE: Tub cover gasket tool, Part No. 273P4, is
designed to spread open hold-down tabs to prevent
tearing of gasket during installation.
IMPORTANT: When installing outer tub cover,
always use a new cover gasket.
NOTE: Clean and remove any foreign material in
gasket groove of outer tub cover and outer tub
flange.
g. Starting at positioning pin located at the bleach
funnel area, lay gasket into gasket groove of tub
cover. Refer to Figure 35.
h. Using your fingers, press gasket down into
gasket groove of tub cover. Avoid pressing
gasket past ends of hold-down tabs.
j. With tub cover tilted at approximately a 45
degree angle, insert the positioning pin into
notch on outer tub flange.
k. Lower cover and push down firmly on top of
hold- down tabs next to positioning pin until
tabs snap over edge of outer tub flange.
l. Cross over to opposite side of tub cover and
push down firmly on top of hold-down tabs
until tabs snap over edge of outer tub flange.
Continue with this criss-cross pattern, until tub
cover is fully seated. Visually check each tab
area again to ensure cover is seated.
IMPORTANT: Care must be taken not to twist or
bunch gasket in any one area to avoid leaks after
assembly.
TUB COVER
GASKET
(continued on Page 53)
273P4
TUB COVER GASKET
TOOL
HOLD-DOWN
TABS
POSITIONING
PIN
PRESS GASKET INTO
GROOVE USING YOUR
FINGERS
W442SE3A
Figure 35
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Section 5 Service Procedures
FILLER
HOSE
HOSE
CLAMP
BLEACH
FUNNEL
OUTER
TUB
COVER
GASKET
OUTER TUB
COVER
TUB
FLANGE
PLACE FINGERS UNDER THIS
AREA AND PULL OUT AND
AWAY FROM TUB AND AT
THE SAME TIME LIFT UP ON
TUB COVER TO REMOVE
COVER OFF TUB FLANGE.
OUTER
TUB
W443SE3C
Figure 36
52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
TO REMOVE BALANCE RING FROM
WASHTUB
a. Place blade of a small screwdriver into slots
between balance ring and washtub.
Refer to Figure 37.
b. Carefully pry pins of balance ring out of holes
in washtub. Refer to Figure 37.
m. Remove screws (and gaskets if present) holding
washtub to hub. Refer to Figure 37.
NOTE: Gaskets are used with porcelain washtubs
only.
IMPORTANT: Porcelain Washtub Models — Use
care when tightening screws to avoid chipping
porcelain on washtub.
n. Lift washtub and balance ring out of outer tub.
NOTE: As you are prying out pins, lift up on
balance ring.
c. Pry at least 7 of the 8 pins out of washtub holes
before balance ring can be removed.
IMPORTANT: When removing washtub and
balance ring, grasp top flange of washtub and
remove from outer tub.
NOTE: When installing washtub, make sure lint
filter is between underside of washtub and hub.
Some models are equipped with a gasket. On these
models, make sure all traces of old gasket are
removed from bottom of washtub. When installing
washtub in these models, always use a new gasket
between washtub and hub.
TO INSTALL BALANCE RING IN
WASHTUB
Place balance ring on top of washtub, making sure
balance ring pins line up with holes in washtub.
Then carefully push balance ring down into
washtub until all pins snap into their respective
holes.
SLOTS
WASHTUB
SCREWS
BALANCE
RING
PINS
W511SE3B
Figure 37
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
39. HUB AND SEAL KIT ASSEMBLY
IMPORTANT: If water is present in washtub, spin
and pump out before removing drive bell.
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
d. Open loading door.
e. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 17.
IMPORTANT: Hooks should be positioned 180
degrees from each other, and must be placed under
agitator vanes for greater stability. If hooks are
placed between vane area, damage to agitator may
occur.
f. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
g. Hinge cabinet top or remove, Paragraph 35.
h. Loosen hose clamp and remove filler hose from
outer tub cover. Refer to Figure 36.
NOTE: When reinstalling filler hose, white line on
hose must point toward front of washer. Refer to
Figure 36.
54
TUB COVER AND GASKET
(1) There are eight tub cover hold-down tabs
which snap over the outer tub flange. Place
your fingers under the flap of the holddown tab of the tub cover. Pull out on flap
and at the same time lift upward on cover
to unsnap hold-down tabs from outer tub
flange. One by one, disengage each of the
eight hold-down tabs from outer tub flange
and remove cover.
(2) Lift cover off outer tub and set beside
washer cabinet.
IMPORTANT: When installing outer tub cover,
always use a new cover gasket.
NOTE: Clean and remove any foreign material in
gasket groove of outer tub cover and outer tub
flange.
(3) Starting at the positioning pin located at the
bleach funnel area, lay gasket into gasket
groove of tub cover. Refer to Figure 35.
(4) Using your fingers, press gasket down into
gasket groove of tub cover. Avoid pressing
gasket past ends of hold-down tabs.
IMPORTANT: Care must be taken not to twist or
bunch gasket in any one area to avoid leaks after
assembly.
(5) Install gasket past ends of hold-down tabs
to bottom of gasket groove using semicurled end of tub cover gasket tool Part No.
273P4. Refer to Figure 35.
NOTE: Tub cover gasket tool, Part No. 273P4, is
designed to spread open hold-down tabs to prevent
tearing of gasket during installation.
(6) With tub cover tilted at approximately 45
degree angle, insert the positioning pin into
notch on outer tub flange.
(7) Lower cover and push down firmly on top
of hold-down tabs next to positioning pin
until tabs snap over edge of outer tub
flange.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
(8) Cross over to opposite side of tub cover
and push down firmly on top of hold-down
tabs until tabs snap over edge of outer tub
flange. Continue with this criss-cross
pattern, until tub cover is fully seated.
Visually check each tab area again to
ensure cover is seated.
i. Remove screws holding washtub to hub.
Refer to Figure 37. Then lift washtub (with
balance ring attached) out of outer tub.
IMPORTANT: When removing washtub, grasp top
flange of washtub and remove from outer tub.
NOTE: When installing washtub, make sure lint
filter or gasket is between underside of washtub and
hub.
TO REMOVE AGITATOR DRIVE BELL
a. Remove plug, screw (and “O” ring if present)
from top side of drive bell.
NOTE: No 294P4 Drive Bell Tool may be required
to remove drive bell from transmission shaft, if not,
proceed to step i.
b. Back bolt out of tool approximately three
quarters of the way. Refer to Figure 18.
c. Place tool over bell, making sure indent on
jaw lines up with the wide slots on bell. Refer
to Figure 18.
d. Screw bolt down through hole in top of bell
until bolt bottoms out in hole in transmission
shaft.
e. Place lip of each jaw under bottom edge of
drive bell, making sure indent on jaw lines up
with wide slots on bell. Then tighten two wing
nuts to hold jaws firmly against drive bell.
Refer to Figure 19.
f. Use an adjustable wrench and turn large nut on
tool COUNTERCLOCKWISE to pull drive
bell from transmission shaft. Refer to
Figure 20.
IMPORTANT: If large nut is turned clockwise
when pulling drive bell, you will twist off quarter
inch bolt.
39311
g. Turn quarter inch bolt out of transmission shaft,
and remove tool and drive bell from washer.
h. Loosen two wing nuts and remove drive bell
from tool.
i. Remove old seal from hub by placing a flat
blade screwdriver between bottom edge of seal
and hub using washtub bolts as a pry area to pop
off lower seal bead. Then grasp seal and pull
straight up freeing the upper seal bead.
j. Remove large hex nut using a No. 306P4 Hex
Wrench. Refer to Figure 38.
k. Remove spline insert from transmission tube.
IMPORTANT: Use a new spline insert each time
hex nut is removed. DO NOT reuse old insert
because hex nut may loosen during washer
operation.
HEX
NUT
TRANSMISSION
OUTPUT SHAFT
HUB
ASSEMBLY
WASHER
BRONZE
BEARING
HUB SHOULDER
W499SE1B
Figure 38
l. Remove hub from splines on transmission tube.
NOTE: It may be necessary to use a gear puller to
remove hub.
m. Remove old water seal from outer tub.
IMPORTANT: Use care when removing old seal so
as not to damage tub flange or porcelain.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
INSTALLING NO. 646P3 HUB AND SEAL
KIT
a. Thoroughly clean all foreign material from
inner surface of outer tub flange.
IMPORTANT: All foreign material must be
removed from inner surface of outer tub flange
before installing No. 646P3 Hub and Seal Kit.
b. Apply a small amount of No. 27615P Sealant
(3M800) (obtain from local Parts Distributor)
around outer surface of tub flange. Refer to
Figure 39.
c. Apply a light film of nonstaining petroleum
jelly (such as Vaseline®) to bronze portion of
water seal and to outer surface of stainless steel
sleeve. Refer to Figure 40.
IMPORTANT: DO NOT over lubricate!
d. Insert stainless steel sleeve into water seal from
bottom of water seal. Refer to Figure 40, until
stainless steel sleeve is flush with bronze
portion of water seal.
e. Leaving garter spring on water seal, place new
water seal over outer tub flange (with seal lip on
outside of tub flange). Then press seal into tub
flange opening using moderate finger pressure.
f. Carefully apply a small amount of No. 27615P
Sealant (3M800) (obtain from local Parts
Distributor) around outer edge of water seal and
tub (area located just below garter spring).
Refer to Figure 40.
i. While holding down hub assembly, place new
spline insert (with fingers pointing upward)
over transmission tube until it bottoms out on
hub assembly.
j. Place large hex nut over transmission tube
(with larger inside bevel toward spline insert)
then finger tighten large hex nut.
k. Torque large hex nut between 40 to 70 footpounds (5.56 to 13.21 Kgm).
NOTE: If torque wrench is not available, place
No. 306P4 Hex Wrench over large hex nut then tap
hex wrench with a hammer until hub assembly
turns or until large hex nut will no longer tighten.
NOTE: If a lint filter was originally installed
between washtub and hub assembly, then it must be
reinstalled before installing washtub in washer.
Proceed to step m.
NOTE: If a gasket was originally installed between
washtub and hub assembly, then No. 39122 Gasket
(supplied in kit) must be installed before installing
washtub in washer. Proceed to step l.
OUTER
TUB FLANGE
APPLY BEAD
OF NO. 27615P
SEALANT
(Step “b”)
IMPORTANT: DO NOT allow sealant to contact
sealing surface of water seal because it will cause a
water leak.
g. Lubricate inner splines of new hub assembly
(supplied in kit) with No. 27604P Anti-Seeze
Compound.
h. Carefully place new hub assembly on splined
transmission tube.
W445SE1A
Figure 39
IMPORTANT: Firmly push hub assembly down
against outer tub seal and hold in this position
during the next three steps.
56
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WATER
SEAL
BRONZE PORTION
STAINLESS STEEL
OF SEAL
SLEEVE
LUBRICATE
LUBRICATE
(Step “c”)
(Step “c”)
PRESS HERE
TO ASSEMBLE
FLUSH
GARTER
SPRING
GARTER
SPRING
APPLY BEAD OF
NO. 27615P
SEALANT (3M800) HERE
(Step “f”)
APPLY BEAD OF
NO. 27615P
SEALANT (3M800) HERE
INSERT STAINLESS STEEL
(Step “f”)
SLEEVE FROM BOTTOM SIDE OF SEAL
W180SE3B
Figure 40
l. To install No. 39122 Gasket, follow these steps:
(1) Thoroughly clean all foreign material from
seal surface area of hub and bronze
bearing.
(2) Apply a small amount of nonstaining
petroleum jelly (such as Vaseline®) to
both surfaces where gasket will contact
hub assembly and bottom of washtub.
(3) Carefully place No. 39122 Gasket
(supplied in kit) on hub assembly.
NOTE: Ensure holes in gasket are aligned with
holes in hub assembly and all traces of original
washtub gasket are removed from bottom of
washtub.
m. Grasp top flange of washtub and carefully
lower washtub down onto lint filter (or gasket)
and hub assembly.
IMPORTANT: Before setting washtub into place,
make sure holes in hub assembly are aligned with
holes in lint filter (or gasket).
n. Secure washtub to hub assembly, using cap
screws and gaskets from 27202P Screw and
Gasket Kit (supplied in kit).
39311
NOTE: Gaskets are used with screws on washers
equipped with a porcelain washtub.
IMPORTANT: Porcelain Washtub Models — Use
care when tightening cap screws to avoid chipping
or damaging porcelain finish.
o. Install No. 38359 Tub Cover Gasket (supplied
in kit) into outer tub cover, Paragraph 38.
IMPORTANT: When installing outer tub cover
always use a new tub cover gasket.
p. Reassemble washtub, Paragraph 38.
q. Install seal, drive bell and agitator following the
instructions supplied in No. 39508P Drive Bell
and Seal Kit.
r. Reinstall cabinet top and front panel.
s. Close loading door, set washer timer to final
spin, start washer and allow empty washtub to
spin for 30 seconds.
IMPORTANT: Setting washer to spin allows
petroleum jelly (applied to bronze portion of water
seal) a chance to cover seal surface before water is
added to washer.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
(continued)
57
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
40. OUTER TUB
a. Open loading door.
b. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 17.
IMPORTANT: Hooks should be positioned 180
degrees from each other, and must be placed under
agitator vane for greater stability. If hooks are
placed between vane area, agitator damage may
occur.
c. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
d. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
e. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
f. Lift front panel off two screws and set panel
aside.
g. Hinge cabinet top or remove, Paragraph 35.
h. Loosen hose clamp, and disconnect filler hose
from outer tub cover. Refer to Figure 37.
NOTE: When reinstalling filler hose, white line on
hose must point toward front of washer. Refer to
Figure 36.
TUB COVER AND GASKET
(1) There are eight tub cover hold-down tabs
which snap over the outer tub flange. Place
your fingers under the flaps of the holddown tab of the tub cover. Pull out on the
flap and at the same time lift upward on
cover to unsnap hold-down tabs from outer
tub flange. One by one, disengage each of
the eight hold-down tabs from outer tub
flange and remove cover.
(2) Remove cover from outer tub and remove
old gasket from tub cover.
NOTE: When installing outer tub cover, always use
a new cover gasket.
NOTE: Clean and remove any foreign material in
gasket groove of outer tub cover and outer tub
flange.
(3) Starting at positioning pin located at the
bleach funnel area, lay gasket into gasket
groove of tub cover. Refer to Figure 35.
(4) Using your fingers, press gasket down into
gasket groove of tub cover. Avoid pressing
gasket past ends of hold-down tabs.
IMPORTANT: Care must be taken not to twist or
bunch gasket in any one area to avoid leaks after
assembly.
(5) Early Models – Install gasket past ends of
hold-down tabs to bottom of gasket groove
using semi-curled end of tub cover gasket
tool Part No. 273P4. Refer to Figure 35.
NOTE: Tub cover gasket tool, Part No. 273P4, is
designed to spread open hold-down tabs to prevent
tearing of gasket during installation.
(6) With tub cover tilted at approximately a 45
degree angle, insert the positioning pin into
notch on outer tub flange.
(7) Lower cover and push down firmly on top
of hold-down tabs next to positioning pin
until tabs snap over edge of outer tub
flange.
58
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
(8) Cross over to opposite side of tub cover
and push down firmly on top of hold-down
tabs until tabs snap over edge of outer tub
flange. Continue with this criss-cross
pattern, until tub cover is fully seated.
Visually check each tab area again to
ensure cover is seated. Refer to Figure 36.
i. Remove screws (and gaskets if present) holding
washtub to hub. Refer to Figure 37.
NOTE: Gaskets are used with porcelain washtubs
only.
IMPORTANT: Porcelain Washtub Models — Use
care when tightening cap screws to avoid chipping
porcelain on washtub.
IMPORTANT: Use care when releasing idler lever
tension. If idler lever spring is overstretched,
washer operation will be affected.
p. While holding idler lever, reach in and around
right side of motor and run belt off right side of
pulley.
q. Using No. 289P4 Spring Hook Tool, unhook
six module springs from lower edge of outer
tub. Refer to Figure 41.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole and in
formed depression in tub skirt.
j. Lift washtub (with balance ring attached) out of
outer tub.
IMPORTANT: When removing washtub and
balance ring, grasp top flange of washtub and
remove from outer tub.
k. Remove agitator drive bell, Paragraph 29.
l. Remove large hex nut using No. 306P4 Hex
Wrench. Then remove spline insert from
transmission tube.
IMPORTANT: Use a new spline insert each time the
hex nut is removed. DO NOT reuse the old insert as
hex nut may loosen during the washer operation.
m. Remove hub from splines on transmission tube.
NOTE: It may be necessary to use a gear puller to
remove hub.
n. Remove old water seal from outer tub.
IMPORTANT: Use care when removing old seal so
as not to damage tub flange or porcelain.
NOTE: When reinstalling or replacing outer tub,
always install a new No. 646P3 Hub and Seal Kit,
Paragraph 39.
o. Reach in through front of motor mounting
bracket and move idler lever to left to release
tension on belt.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
(continued)
59
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
NOTE: To prevent porcelain damage, leg plates
must be installed on outside of outer tub flange
when reinstalling support legs of weldment
assembly. Do not overtighten screws as this could
cause stripping or porcelain damage. Torque
screws between 90 to 130 inch-pounds
(10.30 to 14.87 Nm).
HOLES
z. Turn outer tub upright and remove pressure
bulb and grommet.
NOTE: When installing grommet into outer tub,
thicker lip of grommet must be installed to outside
of tub. Lubricate outer surface of large opening of
pressure bulb with liquid soap to aid when
assembling pressure bulb into grommet.
TUB
SKIRT
MODULE
SPRINGS
TUB-TO-PUMP
HOSE
DRAIN
HOSE
W482SE1B
IMPORTANT: When reinstalling complete tub
modules, carefully set the tub module pivot dome on
top of friction ring. DO NOT ALLOW TUB
MODULE TO BE DROPPED OR LOWERED
INTO POSITION TOO HARD! This can
damage or crack the friction ring.
Figure 41
r. Loosen hose clamp and remove hose from
pump outlet. Refer to Figure 41.
s. Loosen hose clamp and remove pressure hose
from pressure bulb. Refer to Figure 33.
t. Remove wire tie holding motor wire harness to
support leg.
u. Grasp outer tub and lift complete tub module
assembly straight up and out of washer cabinet.
v. Turn outer tub upside-down and set on
protective padding.
w. Remove motor and mounting bracket,
Paragraph 31.
x. Remove screws and lockwashers holding
counterweight and each support leg to outer
tub. Refer to Figure 42. Then lift transmission,
weldment assembly and counterweight off tub.
y. Loosen hose clamp and remove tub-to-pump
hose from bottom of outer tub. Refer to
Figure 41.
60
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
PIVOT
DOME
BRAKE
ASSEMBLY
DRIVE
PULLEY
WELDMENT
ASSEMBLY
COUNTERWEIGHT
TRANSMISSION
ASSEMBLY
LEG PLATE
SCREW AND
LOCKWASHER
W447SE3B
Figure 42
41. DRIVE PULLEY, HELIX AND BRAKE
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife. At the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside. Refer to Figure 25.
d. Hinge cabinet top or remove, Paragraph 35.
e. While holding idler lever, reach in and around
right side of motor and run belt off right side of
pulley.
39311
f. Using No. 289P4 Spring Hook Tool, unhook
six module springs from lower edge of outer
tub. Refer to Figure 41.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole and in
formed depression in tub skirt.
g. Loosen hose clamp and remove drain hose from
pump outlet. Refer to Figure 41.
h. Loosen hose clamp and remove pressure hose
from pressure bulb. Refer to Figure 33.
i. Remove motor harness from support leg. Then
disconnect wire harness from motor switch by
pressing down on top of connection block and
at the same time pull connection block away
from motor switch.
j. Grasp outer tub and lift complete tub module
assembly (with transmission and weldment
assembly attached) straight up and out of
washer cabinet.
k. Turn complete tub module upside-down and set
on protective padding.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
61
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
l. Remove screw, washer and helix holding drive
pulley to input shaft and transmission
assembly. Refer to Figure 43.
IMPORTANT: On tall tub models, the weldment
assembly must be removed or loosened and raised
enough to get pulley off and on the input shaft.
m. Lift drive pulley up and off input shaft of
transmission assembly.
NOTE: When reinstalling pulley, place a small
amount of No. 03200P Lubricant on top side of the
drive pulley that will be contacting large flat
washers. Refer to Figure 44 for assembly sequence.
Lubricate helix ramps and bore with a small
amount of No. 03200P Lubricant. Refer to
Figure 44.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation. This condition will persist
until lubricant is removed.
(continued on Page 64)
CAP SCREW
WASHER
HELIX
DRIVE
PULLEY
COUNTERWEIGHT
THICK
WASHER
THIN
WASHER
TRANSMISSION
ASSEMBLY
W448SE3B
Figure 43
62
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
BEARING
WELDMENT ASSEMBLY
BRAKE
ASSEMBLY
PIVOT
DOME
DO NOT
LUBRICATE
BRAKE
PAD
WASHER
(Thin)
SCREW
WASHER
(Thick)
DRIVE
PULLEY
APPLY
NO. 03200P
LUBRICANT
HERE
HELIX
WASHER
CAP SCREW
FRICTION
RING
WASHER
BASE
W449SE3B
Figure 44
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
63
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
n. Remove screws holding three brake pads and
brake assembly to weldment assembly. Refer to
Figure 44. Then remove brake assembly and
pads off bottom of weldment assembly.
IMPORTANT: When reinstalling brake assembly,
we recommend replacing three brake pads. DO
NOT replace worn pads only. Apply a small amount
of No. 26594P Silicone Lubricant to both sides of
each brake pad where it will contact brake
assembly.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation. This condition will persist
until lubricant is removed.
IMPORTANT: After installing complete tub
module in washer and all hoses have been
reconnected, add at least a quart of water to
washtub to lubricate pump seals. Running a pump
without water will ruin the seals.
NOTE: All models WITHOUT the letter “M” in the
sixth character of the model number — After
washtub has been spinning for two minutes, normal
spin speed should be 640 ± 20 RPM one speed
models; 640 ± 20 RPM FAST speed, or
427 ± 20 RPM SLOW speed on two speed models.
If not, the cause could be dragging brake pads. If
problems occur with steps three or four, remove
brake assembly and correct problem.
NOTE: All models WITH the letter “M” in the sixth
character of the model number — After washtub
has been spinning for two minutes, normal spin
speed should be 710 ± 20 RPM one speed models;
710 ± 20 RPM FAST speed or 473 ± 20 RPM
SLOW speed on two speed models. If not, the cause
could be dragging brake pads. If problems occur
with steps three or four, remove brake assembly
and correct problem.
o. After brake is installed, put washer through the
following check to make sure brake is operating
properly.
(1) Turn off electrical power to washer.
(2) Turn drive pulley one complete revolution
in agitation direction, then push drive
pulley up against brake.
(3) Check for a .030 (.76 mm) minimum gap
between drive pulley and helix ramp
surfaces.
IMPORTANT: If gap is less than .030 (.76 mm),
brake may not stop washtub from spinning in
required seven seconds because brake will not close
properly.
(4) Turn on electrical power to washer and
start washer in the final spin.
64
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
42. WELDMENT AND BEARING ASSEMBLY
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside. Refer to Figure 25.
d. Hinge cabinet top or remove, Paragraph 35.
e. Loosen hose clamp and disconnect filler hose
from outer tub cover. Refer to Figure 34.
NOTE: When reinstalling filler hose, the white line
on hose that connects to tub cover must point
toward front of washer. Refer to Figure 34.
i. Direct Drive Pump Models — Loosen
hose clamp and remove hoses from pump
outlets. Refer to Figure 41.
Electric Pump Models — Loosen hose
clamp and remove hose from bottom of outer
tub.
j. Loosen hose clamp and remove pressure hose
from pressure bulb. Refer to Figure 33.
k. Grasp outer tub and lift complete tub module
assembly (with transmission and weldment
assembly attached) straight up and out of
washer cabinet.
l. Turn complete tub module upside-down and set
on protective padding.
m. Remove screw, washer and helix holding drive
pulley to input shaft and transmission
assembly. Refer to Figure 43.
IMPORTANT: On tall tub models, the weldment
assembly must be removed or loosened and raised
enough to get pulley off and on the input shaft.
n. Lift drive pulley up and off input shaft of
transmission assembly.
IMPORTANT: Use care when releasing idler lever
tension. If idler lever spring is overstretched,
washer operation will be affected.
NOTE: When reinstalling pulley, place a small
amount of No. 03200P Lubricant on top side of the
drive pulley that will be contacting large flat
washers. Refer to Figure 43 for assembly sequence.
Lubricate helix ramps and bore with a small
amount of No. 03200P Lubricant. Refer to
Figure 44.
g. While holding idler lever, reach in and around
right side of motor and run belt off right side of
pulley.
h. Using No. 289P4 Spring Hook Tool, unhook
six module springs from lower edge of outer
tub. Refer to Figure 41.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation. This condition will persist
until lubricant is removed.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole in tub
skirt.
o. Remove screws holding three brake pads and
brake assembly to weldment assembly. Refer to
Figure 44. Then remove brake assembly and
pads off bottom of weldment assembly.
f. Reach in through front of motor mounting
bracket and move idler lever to left to release
tension on belt.
(continued)
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
65
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
IMPORTANT: When reinstalling brake assembly,
we recommend replacing three brake pads. DO
NOT replace worn pads only. Apply a small amount
of No. 26594P Silicone Lubricant to both sides of
each brake pad where it will contact brake
assembly.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation. This condition will persist
until lubricant is removed.
IMPORTANT: After installing complete tub
module in washer and all hoses have been
reconnected, add at least a quart of water to
washtub to lubricate pump seals. Running a pump
without water will ruin the seals.
p. After brake is installed, put washer through the
following check to make sure brake is operating
properly.
(1) Turn off electrical power to washer.
(2) Turn drive pulley one complete revolution
in agitation direction, then push drive
pulley up against brake.
(3) Check for a .030 (.76 mm) minimum gap
between drive pulley and helix ramp
surfaces.
NOTE: All models WITH the letter “M” in the sixth
character of the model number — After washtub
has been spinning for two minutes, normal spin
speed should be 710 ± 20 RPM one speed models;
710 ± 20 RPM FAST speed or 473 ± 20 RPM
SLOW speed on two speed models. If not, the cause
could be dragging brake pads. If problems occur
with steps three or four, remove brake assembly
and correct problem.
q. Remove screws and lockwashers holding
counterweight and each support leg to outer
tub. Refer to Figure 43. Then lift transmission,
weldment assembly and counterweight off tub.
NOTE: It may be necessary to tap lightly on the
weldment assembly to loosen it from transmission
tube.
NOTE: To prevent porcelain damage, leg plates
must be installed on outside of outer tub flange
when reinstalling support legs of weldment
assembly. Do not overtighten screws as this could
cause stripping or porcelain damage. Torque
screws between 90 to 130 inch-pounds
(10.30 to 14.87 Nm).
r. Remove screws and washers holding
counterweight to leg on weldment assembly.
IMPORTANT: If gap is less than .030 (.76 mm),
brake may not stop washtub from spinning in
required seven seconds because brake will not close
properly.
(4) Turn on electrical power to washer and
start washer in the final spin.
NOTE: All models WITHOUT the letter “M” in the
sixth character of the model number — After
washtub has been spinning for two minutes, normal
spin speed should be 640 ± 20 RPM one speed
models; 640 ± 20 RPM FAST speed, or
427 ± 20 RPM SLOW speed on two speed models.
If not, the cause could be dragging brake pads. If
problems occur with steps three or four, remove
brake assembly and correct problem.
66
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
43. TRANSMISSION ASSEMBLY
a. Open loading door.
b. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 17.
IMPORTANT: Hooks should be positioned 180
degrees from each other, and must be placed under
base of agitator near an agitator vane for greater
stability. If hooks are placed between vane area,
damage to agitator may occur.
c. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
d. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
e. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
f. Lift front panel off two screws and set panel
aside. Refer to Figure 25.
g. Remove two cabinet top hold-down screws,
and hinge cabinet top or remove, Paragraph 35.
h. Loosen hose clamp and disconnect filler hose
from tub cover. Refer to Figure 34.
NOTE: When reinstalling filler hose, the white line
or hose that connects to tub cover must point
toward front of washer. Refer to Figure 34.
39311
TUB COVER AND GASKET
(1) There are eight tub cover hold-down tabs
which snap over the outer tub flange. Place
your fingers under the flaps of the holddown tab of the tub cover and pull out on
the flap and at the same time lift upward on
cover to unsnap hold-down tabs from outer
tub flange. One by one, disengage each of
the eight hold-down tabs from outer tub
flange and remove cover.
(2) Remove cover from outer tub and remove
old gasket from tub cover.
NOTE: When installing tub cover, always use a new
cover gasket.
NOTE: Clean and remove any foreign material in
gasket groove of tub cover and outer tub flange.
(3) Starting at positioning pin located at the
bleach funnel area, lay gasket into gasket
groove of tub cover. Refer to Figure 35.
(4) Using your fingers, press gasket down into
gasket groove of tub cover. Avoid pressing
gasket past ends of hold-down tabs.
IMPORTANT: Care must be taken not to twist or
bunch gasket in any one area to avoid leaks after
assembly.
(5) Early Models – Install gasket past ends of
hold-down tabs to bottom of gasket groove
using semi-curled end of tub cover gasket
tool part No. 273P4.
NOTE: Gasket tool, Part No. 273P4, is designed to
spread open hold-down tabs to prevent tearing of
gasket during installation.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
67
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
i. Remove screws and washers holding washtub
to hub. Refer to Figure 37.
IMPORTANT: Porcelain Washtub Models — Use
care when tightening cap screws to avoid chipping
porcelain on washtub.
j. Lift washtub (with balance ring attached) out of
outer tub
IMPORTANT: When removing washtub and
balance ring, grasp top flange of washtub and
remove from outer tub.
k. Remove agitator drive bell, Paragraph 29.
l. Remove large hex nut using No. 306P4 Hex
Wrench. Then remove spline insert from
transmission tube.
m. Remove hub from splines on transmission tube.
NOTE: It may be necessary to use a gear puller to
remove hub.
n. Remove old water seal from outer tub.
IMPORTANT: Use care when removing old seal so
as not to damage tub flange or porcelain.
NOTE: When reinstalling or replacing outer tub,
always install a new No. 646P3 Hub and Seal Kit,
Paragraph 39.
o. Using No. 289P4 Spring Hook Tool, unhook
six module springs from lower edge of outer
tub. Refer to Figure 41.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole in tub
skirt.
p. Direct Drive Pump Models — Loosen
hose clamps and remove hose from pump.
Electric Pump Models — Loosen hose
clamp and remove hose from bottom of outer
tub.
q. Loosen hose clamp and remove pressure hose
from pressure bulb.
r. Remove wire tie holding motor wire harness to
support leg.
s. Grasp outer tub and lift complete tub module
assembly straight up and out of washer cabinet.
t. Turn outer tub upside-down and set on
protective padding.
u. Remove screw, washer and helix holding drive
pulley to input shaft of transmission assembly.
Refer to Figure 43.
IMPORTANT: On tall tub models, the weldment
assembly must be removed or loosened and raised
enough to get pulley off and on the input shaft.
v. Lift drive pulley up and out from between
support legs.
NOTE: When reinstalling pulley, place a small
amount of No. 03200P Lubricant to top side of drive
pulley that will be contacting the large flat washer.
Lubricate helix ramps with a small amount of
No. 03200P Lubricant. Refer to Figure 44.
IMPORTANT: DO NOT OVER LUBRICATE!
Excess lubricant can be thrown into pivot dome
area during normal washer operation. Any
lubricant on pivot dome, base or friction ring will
affect washer operation. This condition will persist
until lubricant is removed.
w. Remove screws and lockwashers holding each
support leg to outer tub. Refer to Figure 44.
Then lift weldment assembly off transmission
tube.
NOTE: It may be necessary to tap lightly on
weldment assembly to loosen it from transmission
tube.
x. Lift transmission assembly out of upper
bearing.
IMPORTANT: Some water will always remain in
outer tub. Therefore, before removing hose from
pump, pinch off or drain hose to prevent water
spillage.
68
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
NOTE: When installing lower bearing, weldment
assembly and brake assembly, apply No. 27604P
Anti-Seeze Compound to area of transmission tube
that will be contacting bearing, washtub hub and
brake assembly. Refer to Figure 45.
To prevent porcelain damage, leg plates must be
installed on outside of outer tub flange when
reinstalling support legs of weldment assembly.
Refer to Figure 42. Do not overtighten screws as this
could cause stripping or porcelain damage. Torque
screws between 90 to 130 inch-pounds (10.30 to
14.87 Nm).
IMPORTANT: When replacing or reinstalling
transmission assembly, it is important that
No. 27604P Anti-Seeze Compound be applied to
area of the transmission tubes where they will be
contacting upper and lower bearings. Refer to
Figure 45.
Carefully lower transmission through upper
bearing. DO NOT DROP OR LOWER
TRANSMISSION ASSEMBLY INTO POSITION
TOO HARD. This can cause bearing to move which
will cause vibration, noise, wear or no spin.
TRANSMISSION
ASSEMBLY
APPLY
NO. 27604P
ANTI-SEEZE
COMPOUND
TO THESE AREAS
OF BOTH UPPER
AND LOWER
TRANSMISSION TUBES
UPPER
BEARING
W450SE3A
Figure 45
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
69
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
TO DISASSEMBLE TRANSMISSION
ASSEMBLY
(Refer to Figure 46 for assembly sequence)
a. Place transmission in a vise with input shaft end
up. Clamp only the case, not the shaft.
NOTE: Supporting transmission in this manner will
allow oil to collect in the transmission case.
b. Before disassembling transmission halves,
mark outer edge of transmission case and cover
so two can be reassembled in the same position.
c. Place transmission in vise so three of the eight
screws holding transmission case and cover
together are in the twelve, four and seven
o’clock positions.
d. Loosen three screws, mentioned in step “c”,
approximately two turns. DO NOT remove
these three screws at this time. Remove
remaining five screws and lockwashers
completely.
e. Remove transmission assembly from vise.
f. While holding transmission by cover end,
gently tap each of the three remaining screws
until two halves separate. Place assembly back
into vise (cover end up) and remove three
screws and lockwashers.
g. Remove screw and washer holding reduction
gear to transmission cover and remove gear.
h. Remove special screw, lockwasher and flat
washer holding drive pinion to input shaft.
k. Remove internal gear, slide and rack from
transmission case.
l. Remove transmission case from vise and drain
oil.
m. Remove retainer ring from output shaft.
n. Using a hammer and punch, carefully drive
shaft out of agitator pinion.
o. Carefully remove output shaft and washer from
transmission case.
IMPORTANT: Carefully examine area inside
transmission case tube (seals, bearings, etc.). If oil is
present between seals and bearings, it will require
replacing complete transmission case. Seals and
bearings are not available separately.
IMPORTANT: Transmissions produced after 5/95
may be difficult to disassemble. Take extra care not
to damage sealing surfaces of transmission case and
cover.
NOTE: To prevent input shaft from turning during
removal of special screw, place an old helix onto
shaft and hold helix with a locking pliers.
i. Remove drive pinion from input shaft using a
hammer and punch to drive shaft out of pinion.
j. Remove input shaft from transmission cover.
IMPORTANT: Carefully examine area inside cover
tube (seals, bearing, roller clutch, etc.). If oil is
present between seals and bearing, or roller clutch
is bad, it will require replacing complete
transmission cover assembly. These components are
not available separately.
70
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
TO REASSEMBLE TRANSMISSION
ASSEMBLY
IMPORTANT: Wash all components in a cleaning
solution (mineral spirits). Wipe inside of
transmission case and cover with a clean cloth,
dampened with cleaning solution, to remove any
impurities. DO NOT allow cleaning solution to
come in contact with bearings and seals in
transmission case and/or cover.
a. Carefully insert output shaft and washer into
transmission case.
b. Place agitator pinion on splines of output shaft
and press onto shaft.
c. Install retainer ring on output shaft.
d. Place transmission case into a vise. Clamp only
the case, not the shaft.
e. Place rack inside transmission case with rack
resting on bar in case. Agitator pinion must
engage the rack.
NOTE: Put a light film of transmission oil on bar
where rack will slide back and forth.
f. Position slide in slot in rack.
NOTE: Put a light film of transmission oil in slot on
rack, and also the transmission case where internal
gear will ride.
g. Place internal gear into transmission case.
Make sure guide pin on internal gear fits in hole
in slide.
IMPORTANT: Never install a used internal gear in
a new transmission case. If transmission case and
internal gear are to be reused, be sure they are used
as the original set.
h. Refill transmission case with new No. 27243P
Transmission Oil (one fill).
i. To prevent seal damage, insert input shaft into
cover starting at outer end of cover tube.
j. Install drive pinion, flat washer, lockwasher
and special screw onto input shaft.
NOTE: Use a thread locking compound on threads
of special screw to prevent screw from loosening on
shaft.
IMPORTANT: Make sure mating surfaces of
transmission cover and case are free of oil or any
other foreign material.
k. Place reduction gear on stub shaft of cover and
install screw and washer.
l. Apply a bead of No. 37577P Sealant on mating
surface of transmission case.
IMPORTANT: Bead of sealant should be no more
than one sixteenth inch in diameter. DO NOT allow
any sealant to contact edges of internal gear (sealant
may damage moving parts).
NOTE: A transmission pin tool, Part No. 305P4,
must be used to align the cover and case when
reassembling the transmission after repair. The
transmission pin tool must be used in sets of two and
placed in the same holes shown in Figure 46. Both
transmission pin tools must be left in place until all
eight screws and nuts have been installed and
tightened firmly, then remove the two pins.
m. Carefully place transmission cover over top of
transmission case. Make sure holes in cover
line up with holes in case, and marked edges of
two halves are aligned.
n. Carefully lower cover onto case.
o. Secure two transmission halves together, using
eight screws removed during disassembly.
Tighten eight screws evenly.
p. Remove complete transmission assembly from
vise.
q. Apply Anti-Seeze Compound, No. 27604P, to
smooth area of both transmission tubes that will
be contacting upper and lower bearings. Refer
to Figure 45.
IMPORTANT: End of shaft with identification
groove must be facing outward. Refer to Figure 46.
This is the end that will mate with the helix.
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
71
Section 5 Service Procedures
SHAFT
(Output)
TRANSMISSION
OIL
(1 Fill)
RETAINER
RING
WASHER
TRANSMISSION
CASE
INTERNAL
GEAR
AGITATOR
PINION
SPECIAL
SCREW
RACK
LOCKWASHER
SLIDE
SCREW
WASHER
WASHER
DRIVE
PINION
SHAFT
(Input)
REDUCTION
GEAR
TRANSMISSION
ASSEMBLY
TRANSMISSION
COVER
IDENTIFICATION
GROOVE
(Place
No. 305P4
Pin Tools in
These Holes)
CAP
SCREW
W334PE3A
Figure 46
72
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
44. UPPER BEARING ASSEMBLY
a. Remove transmission assembly, Paragraph 43,
steps “a” through “t”.
b. Remove screws and lockwashers holding each
support leg to outer tub. Refer to Figure 42.
c. Lift complete weldment assembly (with drive
pulley, brake assembly, lower bearing, and
transmission assembly attached) off outer tub.
IMPORTANT: To prevent porcelain damage, leg
plates must be installed on outer tub flange when
reinstalling support legs. (Plate must be installed on
outside of tub flange). Do not overtighten screws as
this could cause stripping or porcelain damage.
d. Remove three screws holding upper bearing
and housing to bottom of outer tub. Refer to
Figure 47.
NOTE: Replace bearing and housing as an
assembly. Refer to Figure 47.
NOTE: When upper bearing assembly is
reinstalled, threads of cap screws must be secured
with a retaining compound.
BALL BEARING
CAP SCREW
OUTER
TUB
UPPER
BEARING
HOUSING
UPPER
BEARING
HOUSING
W453SE3A
Figure 47
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
73
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
45. FRICTION RING
NOTE: Screws at bottom edge of front panel do not
have to be removed as the holes in front panel are
slotted.
NOTE: Top edge of front panel is held in place by
two spring clips located on bottom flange of cabinet
top. Refer to Figure 25.
a. Insert putty knife between cabinet top and top
edge of front panel (aproximately three inches
in from side). Refer to Figure 25.
b. Push in on putty knife and at the same time, pull
top edge of front panel away from front of
washer. Repeat for opposite side.
c. Lift front panel off two screws and set panel
aside.
d. Remove two cabinet top hold-down screws.
Refer to Figure 25.
e. If area or space permits, tape loading door
closed and lift cabinet top to a vertical position
by hinging it on the rear hinges.
NOTE: Cabinet top is self supporting, however, a
small chain may be used for additional support.
Refer to Figure 31.
f. Loosen hose clamps and remove pressure hose
from pressure bulb and filler hose from tub
cover.
g. Loosen hose clamp and remove drain hose from
pump.
h. Disconnect wire harness from motor switch by
pressing down on locking tab on top of
connection block and at the same time pull
connection block away from motor switch.
Refer to Figure 26. Disconnect harness from
leg by squeezing tabs on cable tie together and
push it back through hole in leg.
IMPORTANT: To avoid an open circuit, DO NOT
pull on terminal block wires when removing block
from motor switch as this could damage wires or
connection crimpings. Before attaching wire
harness connection block to motor switch, make
sure all male terminals on motor switch are straight
and are capable of accepting terminals from wire
harness connection block.
74
i. Using No. 289P4 Spring Hook Tool, unhook
six module springs from lower edge of outer
tub. See Figure 41.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole in tub
skirt.
j. Grasp outer tub and lift complete tub module
assembly (with transmission and weldment
assembly attached) straight up and out of
washer cabinet and set out of the way.
k. Remove old friction ring from washer base.
Refer to Figure 48.
l. Use a dry cloth or a cloth dampened with water
and clean the surface of the base where new
friction ring will be installed.
m. Carefully place complete tub module back into
washer making sure the weldment assembly is
positioned properly over the friction ring and
the recess area of washer base. Refer to
Figure 48.
IMPORTANT: When reinstalling complete tub
module, carefully set the tub module pivot dome on
top of friction ring. DO NOT ALLOW TUB
MODULE TO BE DROPPED OR LOWERED
INTO POSITION TOO HARD! This can
damage or crack the friction ring.
NOTE: Be sure motor is facing toward front of
washer.
n. Use the No. 289P4 Spring Hook Tool and
starting with the rear springs, hook six module
springs into lower edge of outer tub. Refer to
Figure 41.
IMPORTANT: When installing module springs,
make sure spring hook is fully seated in hole in tub
skirt. Refer to Figure 41.
o. Direct Drive Pump Models —
Reconnect hose to pump outlet and tighten hose
clamp.
Electric Pump Models —Reconnect
hose to bottom of outer tub and tighten hose
clamp.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
p. Reconnect the connection block to motor
switch. Refer to Figure 26. Reinstall cable tie in
leg making sure it is secure.
q. Reconnect pressure hose to pressure bulb.
Refer to Figure 49. Then connect filler hose to
tub cover. Refer to Figure 49.
r. Reinstall cabinet top and washer front panel.
s. Reconnect washer power cord and open water
supply faucets.
NOTE: Washer must be run through a complete
cycle to make sure it is operating properly.
NOTE: When reinstalling filler hose, white line on
hose that connects to tub cover must point toward
front of washer. Refer to Figure 49. Make sure hose
is in its natural position (not kinked or twisted). If
hose is not, loosen hose clamp and straighten hose.
FRICTION
RING
WASHER
BASE
W454SE3A
Figure 48
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
75
Section 5 Service Procedures
PRESSURE
HOSE
PRESSURE
BULB
FILLER
HOSE
TUB
COVER
PRESSURE HOSE
CLAMP
W455SE3B
Figure 49
76
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 6
Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
46. LEVELING LEGS
(Refer to Figure 50)
a. Place rubber feet on all four leveling legs.
b. Place washer in position on a clean, dry, and
reasonably firm floor.
c. Loosen locknuts and adjust two front leveling
legs. Once adjusted, tilt washer forward on
front legs and lower back down into position to
set the rear self-leveling legs.
d. Washer must not rock. After washer is at
desired height, tighten locknuts securely
against bottom of washer base. If these locknuts
are not tight, washer will not remain stationary
during operation.
NOTE: Improper installation, installation on carpet
or flexing of a weak floor will cause excessive
vibration.
IMPORTANT: Do not slide washer across floor
once leveling legs have been extended, as legs and
base could become damaged.
LEVEL
WASHER
BASE
LOCKNUT
LEVELING
LEG
RUBBER
FOOT
W456SE3A
Figure 50
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
77
Section 6 Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
47. PRESSURE SWITCH
(Refer to Figure 51)
ADJUSTING
SCREW
NOTE: DO NOT ADJUST PRESSURE SWITCH
IF WASHER IS WITHIN THE WARRANTY
PERIOD.
Pressure switch is set at the factory for proper water
fill levels. However, if there is a problem of
overfilling or underfilling, pressure switch can be
adjusted.
Maximum water fill level can be increased by
turning adjusting screw CLOCKWISE, and
decreased by turning screw
COUNTERCLOCKWISE.
One quarter turn of the adjusting screw represents
approximately one inch (25.4 mm) increase or
decrease of water level in washtub.
W457SE1B
Figure 51
48. BELT (Agitate And Spin)
No belt adjustment is required.
IMPORTANT: DO NOT turn adjusting screw
more than 3/4 of a turn in either direction as the
switch may be damaged and flooding could result.
When testing, pressure switch has continuity from
terminal 1 to 2 when empty and 1 to 3 when full.
78
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 7
Test Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
49. MOTOR TEST PROCEDURE
IMPORTANT: Disconnect base wire harness plug from motor.
WARNING
Disconnect electric power to washer before performing the following steps:
W188
Motor test procedures using an Ohm meter.
NOTE: Resistance readings slightly out of given ranges may be due to meter conditions. These readings DO
NOT necessarily indicate motor failure.
Meter Connections
1.
2.
3.
4.
5.
6.
7.
Ground to Each Other Terminal
White to Yellow
Red to Brown
Blue to White
Reading
Should Be
Open
Closed
2-8 Ohms
1-2 Ohms
Violet to White (2-speed motor)
“R” to Red
“P” to Blue (2-speed motor)
2.5 Ohms
(Approximate)
Closed
Closed
If Not
Terminal shorted to ground.
Open thermal overload.
Start winding open or resistance too high or too
low.
High speed winding (4 pole) open or resistance
too high or too low.
Low winding opening; High speed winding open;
or resistance too high or too low.
Open start (auxiliary) switch.
Open start switch 4 pole winding.
NOTE: Steps 8, 9 and 10 are with motor centrifugal mechanism in the run position.
8.
9.
10.
39311
“R” to Red
“P” to Blue (2-speed motor)
“P” to Blue (2-speed motor)
Open
3 Ohms
(approximate)
Closed
Start auxiliary switch.
Refer to Blue to White and Violet to White.
Open low (6 pole) winding run switch.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
79
Section 7 Test Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
50. MIXING VALVE SOLENOID TEST PROCEDURE
Mixing valve test procedures using an Ohm meter.
NOTE: Resistance readings slightly out of given ranges may be due to meter conditions. These readings DO
NOT necessarily indicate mixing valve failure.
120 Volt coils
240 Volt coils
900 - 1100 Ohms
3200 - 4000 Ohms
51. TEMPERATURE SWITCH TEST PROCEDURE
Check for continuity between the following terminal connections:
3 Position Switches
Temperature
Wash
Hot
Warm
Cold
Rinse
Cold
Cold
Cold
Connection
L-3
L - 3- 4
L-4
4 Position Switches
Temperature
Wash
Hot
Rinse
Cold
Warm
Warm
Warm
Cold
Cold
Cold
Connection
L1 - 2
L1 - 1, L1 - 2, L2 - 2, L2 - 1,
L2 - L1, 1 - 2
L1 - 2, L1 - 1, 1 - 2
L1 - 1
5 Position Switches
Temperature
Wash
Hot
Hot
Warm
Warm
Cold
80
Rinse
Cold
Warm
Cold
Warm
Cold
Connection
L1 - 2
L1 - 2, L2 - 2
L1 - 1, L1 - 2
L1 - 1, L1 - 2, L2 - 2
L1 - 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 8
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
*MOTOR
SPEED
H,W,C
FAST
15:00
REGULAR
SPIN
FAST
1:30
C
FAST
:25
FAST
2:35
W,C
FAST
3:00
FAST
1:30
SPIN & SPRAY
SPIN
RINSE FILL & AGITATE
TIME (Min.
& Sec.)
SPIN
SPIN & SPRAY
C
SPIN
FAST
:25
FAST
7:05
FAST
9:00
SLOW
1:30
OFF
3:00
PERMANENT
PRESS
WASH, FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
SPIN & SPRAY
C
SPIN
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
1:30
FAST
:25
FAST
7:05
3:00
DELICATE
OFF
WASH, FILL & SOAK
H,W,C
WASH, FILL & AGITATE
H,W,C
WASH, FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
2:35
SLOW
:25
2:35
SLOW
:25
1:05
SLOW
1:30
SLOW
:25
SLOW
2:35
C
SLOW
3:00
SLOW
1:30
SPIN
SPIN & SPRAY
:25
C
SPIN
RINSE FILL & AGITATE
1:30
SLOW
C
SPIN
OFF
SLOW
:25
SLOW
4:05
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37925 CYCLE SEQUENCE
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
81
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
WATER
TEMP.
SELECT
*MOTOR
SPEED
SOAK, FILL & AGITATE
H,W,C
SLOW
SOAK, FILL
H,W,C
SOAK
CYCLE
FUNCTION
SPIN
TIME (Min.
& Sec.)
4:00
12:00
SLOW
OFF
4:00
4:00
REGULAR
WASH, FILL & AGITATE
H,W,C
SPIN
15:30
FAST
2:00
C
FAST
:30
FAST
1:30
W,C
FAST
4:00
FAST
6:00
FAST
9:30
SLOW
2:00
SLOW
:30
SLOW
1:30
FAST
4:00
FAST
6:00
SPIN & SPRAY
SPIN
RINSE FILL & AGITATE
FAST
SPIN
4:00
PERMANENT
PRESS
OFF
WASH, FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
4:00
DELICATE
OFF
WASH, FILL & SOAK
H,W,C
WASH, FILL & AGITATE
H,W,C
WASH, FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
3:00
SLOW
:30
1:30
SLOW
:30
1:30
SLOW
:30
1:30
SLOW
:30
1:30
SLOW
2:00
SLOW
:30
SLOW
1:30
SLOW
4:00
SLOW
4:00
4:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37927 CYCLE SEQUENCE
82
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
REGULAR
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
15:00
FAST
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
3:00
PERMANENT
PRESS
OFF
WASH, FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
9:00
SLOW
1:30
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
6:00
3:00
DELICATE
OFF
WASH, FILL & SOAK
H,W,C
WASH, FILL & AGITATE
H,W,C
WASH, FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
1:30
SLOW
2:35
SLOW
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
:25
2:35
SLOW
:25
1:05
SLOW
SPIN & SPRAY
:25
1:30
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37928 CYCLE SEQUENCE
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
83
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
REGULAR
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
15:00
FAST
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
3:00
PERMANENT
PRESS
OFF
WASH, FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
9:00
SLOW
1:30
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
6:00
3:00
DELICATE
OFF
WASH, FILL & SOAK
H,W,C
WASH, FILL & AGITATE
H,W,C
WASH, FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
1:30
SLOW
2:35
SLOW
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
:25
2:35
SLOW
:25
1:05
SLOW
SPIN & SPRAY
:25
1:30
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37929 CYCLE SEQUENCE
84
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
REGULAR
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
15:00
FAST
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
3:00
PERMANENT
PRESS
OFF
WASH, FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
9:00
SLOW
1:30
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
6:00
3:00
DELICATE
OFF
WASH, FILL & SOAK
H,W,C
WASH, FILL & AGITATE
H,W,C
WASH, FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
1:30
SLOW
2:35
SLOW
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
:25
2:35
SLOW
:25
1:05
SLOW
SPIN & SPRAY
:25
1:30
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37930 CYCLE SEQUENCE
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
85
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
REGULAR
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
15:00
FAST
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
3:00
PERMANENT
PRESS
OFF
WASH, FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
9:00
SLOW
1:30
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
6:00
3:00
DELICATE
OFF
WASH, FILL & SOAK
H,W,C
WASH, FILL & AGITATE
H,W,C
WASH, FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
1:30
SLOW
2:35
SLOW
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
:25
2:35
SLOW
:25
1:05
SLOW
SPIN & SPRAY
:25
1:30
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37931 CYCLE SEQUENCE
86
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
*MOTOR
SPEED
H,W,C
FAST
PERMANENT
PRESS
PAUSE (:23) & DRAIN
TIME (Min.
& Sec.)
9:35
1:13
FILL AND PAUSE
C
2:25
DRAIN
2:00
DRAIN & SPIN
RINSE FILL & AGITATE
W,C
SLOW
2:23
FAST
4:23
PAUSE (:23) & DRAIN
2:23
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
C
DRAIN & SPIN
FAST
1:34
FAST
:52
FAST
4:45
OFF
3:36
REGULAR
WASH, FILL & AGITATE
H,W,C
FAST
14:23
PAUSE (:23) & DRAIN
2:23
DRAIN & SPIN
2:23
PAUSE
:23
RINSE FILL & AGITATE
W,C
FAST
PAUSE (:23) & DRAIN
4:23
2:23
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
FAST
C
DRAIN & SPIN
OFF
1:34
FAST
:52
FAST
4:45
3:36
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37995 CYCLE SEQUENCE
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
87
Section 8 Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
PERMANENT PRESS
WASH, FILL & AGITATE
WATER
TEMP.
SELECT
*MOTOR
SPEED
H,W,C
FAST
PAUSE
TIME (Min.
& Sec.)
9:41
2:23
DRAIN
:30
FILL & PAUSE
C
2:06
DRAIN
2:00
DRAIN & SPIN
RINSE FILL & AGITATE
W,C
SLOW
2:00
FAST
4:07
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
FAST
DRAIN/SPIN/SPRAY
C
DRAIN & SPIN
1:40
FAST
:47
FAST
4:13
OFF
7:30
WASH, FILL & PAUSE
1:24
AGITATE
H,W,C
SLOW
PAUSE
AGITATE
H,W,C
SLOW
PAUSE
:47
1:36
AGITATE
DELICATE
:47
1:36
H,W,C
SLOW
PAUSE
:35
1:55
DRAIN
:30
FILL & PAUSE
W,C
2:06
DRAIN
2:00
DRAIN & SPIN
SLOW
2:00
SLOW
1:40
PAUSE
:40
RINSE FILL & AGITATE
W,C
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
SLOW
W,C
DRAIN & SPIN
1:40
SLOW
:47
SLOW
4:13
FAST
14:55
OFF
7:30
REGULAR
WASH, FILL & AGITATE
H,W,C
PAUSE (:40) & DRAIN
2:40
DRAIN & SPIN
2:00
PAUSE
:40
RINSE FILL & AGITATE
W,C
FAST
PAUSE (:40) & DRAIN
4:07
3:00
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
FAST
COLD
DRAIN & SPIN
OFF
1:40
FAST
:47
FAST
4:13
7:30
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 39445 CYCLE SEQUENCE
88
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311
Section 9
Internal Wiring of Washer Motor Switch
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
R
BR
BU
P W
Y
WHITE
BROWN
BLUE
YELLOW
RED
RUN
BR
BU
Y
R
W
G
START
W310SE3A
RED
WHITE
N
BROW
W
YELLO
BLUE
4P M
YELLOW
OVERLOAD
PROTECTOR
AUX.
W211SE3A
MOTOR ASSEMBLY
(1 Speed Motors)
39311
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
89
Section 9 Internal Wiring of Washer Motor Switch
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
R
WIRE
HARNESS
CONNECTION
BLOCK
BR
P
W
Y
BU
WHITE
BLUE
BROWN
WHITE
RUN
W311SE3B
BR
BU
Y
R
P
W
G
START
VIOLET
YELLOW
RED
RED
VIOLE
T
BLUE
N
BROW
W
YELLO
4P M
YELLOW
OVERLOAD
PROTECTOR
6P M
AUX.
W224SE3A
MOTOR ASSEMBLY
(2 Speed Motors)
90
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39311