Smeg combined installation manual A 300807 - 2.qxd

INSTALLATION & USER INSTRUCTIONS
FREESTANDING ELECTRIC SUITE
Superior Fires
Christchurch, Dorset BH23 2BT
Tel: 01202 588 632
Fax: 01202 499326
www.superiorfires.co.uk
Email : sales@superiorfires.co.uk
MODELS COVERED BY THESE INSTRUCTIONS
AVONBURY ELECTRIC SUITE RANGE
GB IE
MODEL AVONBURY LED
Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not permitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.
All instructions must be handed to the user
for safekeeping.
1
Revision A- 07/15
© 2015 Focal Point Fires plc.
I N S TA L L AT I O N & U S E R I N S T R U C T I O N S
Section
1.0
2.0
3.0
4.0
5.0
6.0
Contents
Page No.
Important Notes
2
Appliance Data
2
Electrical Installation Requirements
2
Site Requirements
3
Clearances to Combustible Materials
3
Unpacking the Appliance
3
Section
7.0
8.0
9.0
10.0
11.0
12.0
13.0
1.0 IMPORTANT NOTES
Contents
Component Checklist
Operating the Appliance
Safety Cut-Out System
Cleaning and Maintenance
Servicing
Appliance Dimensions
Guarantee - Terms and Conditions
GB IE
Page No.
3
3
4
4
4
5
5
IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
When using this electrical appliance, basic precautions should be followed to reduce the risk of fire, electric shock and injury to person, including the following:
• This heater must be used on an AC supply only and the voltage marked on the heater’s rating label must correspond to the supply voltage.
• Do not switch the appliance on until it is properly installed as described in this manual.
• The heater must not be located immediately above a socket outlet.
• Keep furniture, curtains and other fabric material away from the appliance.
• Do not leave the appliance unattended during use.
• This appliance is intended for household use and should not be used for industrial purposes.
• From time to time, check the cord for damage. Never use the appliance if the cord or any part of the appliance shows signs of damage. A damaged
cord must only be replaced by a qualified person.
• Do not operate this appliance with a damaged plug or cord, after a malfunction or after being dropped or damaged in any way.
• Repairs to electrical appliances should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.
• Do not run the mains cable under carpets, rugs etc.
• Do not cover or obstruct the heater in any way. Overheating will result if it is accidentally covered.
• Never immerse the product in water or any other liquids.
• Do not use this heater where it may come into contact with water e.g. in bathrooms, shower rooms etc.
• Do not use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cool.
• Do not clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.
• There are no other replacement parts. All other servicing should be referred to a qualified engineer.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• CAUTION! In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an
external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility.
• CAUTION! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vunerable people are present.
• Do not insert or allow foreign objects to enter the inlet or outlet vents as this may result in electric shock, fire or damage to the appliance.
• Do not install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
• WARNING! This heater is equipped with a device to control the room temperature. Do not use this heater in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
• WARNING! Children of less than 3 years should be kept away unless continuously supervised. Children aged 3 years and less than 8 years shall
only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involed. Children aged from 3 years and less than 8 years
shall not plug in, regulate and clean the appliance or perform user maintenance.
DO NOT recess any part of appliance into the wall.
The appliance is supplied with a pre-wired three pin plug (13 Amp fuse rated) and 1.8 metres of electrical cable. It is therefore necessary for a
suitable electrical socket to be located within this distance and be easily accessible.
2.0 APPLIANCE DATA
Weight (kg):
Dimensions (mm):
Voltage (Volts):
Heating Elements:
Supply Cord:
Supply Plug:
Location:
Lighting:
32 kg
H 855 x W 850 x D 235
230-240V a.c. 50Hz
1800 Watts
1.8 metres
BS 1363, 13A Fused
Indoor Use
LED
3.0 ELECTRICAL INSTALLATION REQUIREMENTS
The appliance is designed to be floor mounted only. DO NOT RECESS ANY PART OF THE APPLIANCE.
The appliance is supplied with a pre-wired three pin BS1363 plug (13 Amp fuse rated), and 1.8 metre cable. A standard switched outlet/wall
socket, (including earth provision), must therefore be located within this distance, and be easily accessible in order to isolate the supply for
maintenance and cleaning. This socket must not be mounted behind or above the appliance.
IMPORTANT: THIS APPLIANCE MUST BE EARTHED.
2
© 2015 Focal Point Fires plc.
4.0 SITE REQUIREMENTS
GB IE
The appliances are designed to be floor mounted. It is not necessary to secure the surround to the wall, provided it is sited on a firm level surface.
It should be noted that the appliance creates warm convected air currents. These currents move heat from the room surroundings to, and up
the wall surfaces adjacent to the heater.
Operating the heater where impurities in the air, (such as tobacco smoke) exist, may slightly discolour wall finishing. Once the suite is in the
desired location check that it is level and it sits firmly on the floor, i.e. does not rock in any direction, and fits squarely against the wall.
Note: Skirting boards may need to be cut in order to fit the rear of the suite snugly against the wall, Provision must be made in the wall, either
behind the suite, or in one of the sides of the suite to allow the power supply cable to exit.
DO NOT
-
mount on a wall.
recess any part of the appliance into the wall.
site in a position where curtains or drapes could cover the appliance.
site in a position where other soft materials could cover e.g. below a coat rack.
site behind an opening door where mechanical impact/damage could occur.
site where the supply cable would become a trip hazard.
sit, stand or forcefully pull on the appliance.
obstruct, cover or force items into the openings.
use the heater to dry clothes.
site/use in an outdoor location(s).
run the supply cable under carpets.
5.0 CLEARANCES TO COMBUSTIBLE MATERIALS
It is important that the following clearances are maintained from the appliance to combustible materials and are dependant on the desired
mounting location as defined below.
This appliance is designed to be floor mounted only.
The minimum distance from the top of the appliance to a ceiling is 500mm.
The minimum distance to the sides of the appliance is 100mm.
The minimum distance to the front of the appliance is 500mm.
A shelf of any size or design may me mounted above the appliance.
6.0 UNPACKING THE APPLIANCE
Caution: This appliance is heavy. Always seek assistance whilst unpacking and/or during installation.
Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging. Check that
the remaining packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
7.0 COMPONENT CHECKLIST
QUANTITY
1
1
1
DESCRIPTION
Fire suite
Remote control handset
Instruction Booklet
8.0 OPERATING THE APPLIANCE
Check that the fan outlet, mounted underneath the appliance, is not covered or obstructed in any way. Ensure the power to the fire is switched
ON.
REMOTE CONTROL
POWER - ON/OFF
OFF will cancel the OFF TIMER and the flame brightness slowly fades to OFF.
FLAME BRIGHTNESS (5 settings)
Press ∧ / ∨ to adjust the brightness level
FULL (5) - HIGH (4) - MEDIUM (3) - LOW (2) - DIM (1)
HEATING (7 settings)
Press ∧ / ∨ to adjust the temperature level
60℃/99°F - 30℃/86°F - 28℃/82°F - 26℃/78°F - 24℃/75°F - 22℃/71°F - OFF - (LOOP)
3
© 2015 Focal Point Fires plc.
8.0 OPERATING THE APPLIANCE- CONTINUED
GB IE
OFF TIMER
Press to set the OFF TIMER
10m - 20m - 30m - 40m - 50m - 1H - 2H - 3H - 4H - 5H - 6H - 7H - 8H - 9H - (LOOP)
CONTROL PANEL
EMBER/FUEL BED EFFECT
Press to select the dynamic fuel bed effect
POWER ON/OFF
FLAME BRIGHTNESS (5 settings)
Press to adjust the brightness level
FULL (5) - HIGH (4) - MEDIUM (3) - LOW (2) - DIM (1) - (LOOP)
HEATING (7 settings)
Press ∧ / ∨ to adjust the temperature level
60℃/99°F - 30℃/86°F - 28℃/82°F - 26℃/78°F - 24℃/75°F - 22℃/71°F - OFF - (LOOP)
Press button for 10s to convert between ℃ and ℉ (model dependent)
EMBER/FUEL BED EFFECT
Press to select the dynamic fuel bed effect
9.0 SAFETY CUT-OUT SYSTEM
This appliance has a safety cut-out system fitted which will activate if the air inlets or heater outlets are obstructed. For safety reasons the fire
WILL NOT switch on again automatically. NOTE: The LED display panel will remain operational if the cut-out is activated, only the fan heater
elements are prevented from operating.
The following procedure must be carried out before the fire can be operated again:
1. Unplug the power supply cable at the outlet socket and place all switches to off at the appliance.
2. Leave the fire OFF for a period of not less than 10 minutes, ensuring any obstructions are removed.
3. Plug in the power supply cable at the outlet socket, and then switch on at the appliance.
If an attempt to switch on is made before the safety cut-out has reset, the heaters may cut-out for a further period of time. If the sequence has
been followed correctly and the heaters still fail to function, check the power supply cable plug is plugged in at the outlet socket. If this is not
the cause, call an electrician.
10.0 CLEANING AND MAINTENANCE
ALWAYS DISCONNECT THE APPLIANCE AT THE SUPPLY OUTLET SOCKET BEFORE UNDERTAKING ANY CLEANING.
Except for periodic cleaning of dust, there are no specific requirements for care, other than regular cleaning of the general appliance. A wipe
with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Make sure the heater outlet grille (located next to the switches), and the air inlet mesh grilles (located either side of the outlet grille) are kept clear of dust, pet hair and other airborne
household matter. These should be vacuum cleaned periodically using a brush attachment.
PLASTIC SCREEN - This should only be cleaned using a suitable glass cleaner. Test on a small area first.
11.0 SERVICING
There are no internal user serviceable parts.
Check security of supply cable and connections. If the supply cable becomes damaged, it must be replaced by a service agent or competent person, such as a qualified electrician.
The wires in the cable are coloured in accordance with the following code:
LIVE
- Brown
NEUTRAL
- Blue
EARTH
- Green/Yellow
Refer to Section 2.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available from your supplier.
4
© 2015 Focal Point Fires plc.
12.0 APPLIANCE DIMENSIONS
11.0 GUARANTEE - TERMS AND CONDITIONS
All dimensions in mm.
The 3 year guarantee commences from the date of purchase, provided that the following 3 terms and conditions are adhered
FIN: to:
Registration is not required.
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your proof
of purchase.
2. Your gas fire must have been commissioned by a CORGI/Gas Safe* registered installer, evidence of which you must provide together
with the CORGI/Gas Safe* registration number.
3. Your appliance must have been serviced annually, irrespective of use, by a CORGI/Gas Safe* registered installer, evidence of which
must be provided, such as the receipt.
Please note all consumable items such as any ceramics including; coals, pebbles, the matrix, front strips, side cheeks, rear panels and
tapered rear panels are not covered by the 3 year guarantee.For all Electric fires purchased the 3 year guarantee commences from
the date of purchase, providing that you can supply the proof of purchase. This does not cover consumable items such as pebbles,
coals or light bulbs.
Making a claim is easy.
If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then please
submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you can email or
fax.Please note that this does not affect your statutory rights.
Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.
Alternatively email: 3g@focalpointfires.co.uk or fax. 01202 499326.
Details required:
1. Name, full address including post code and contact telephone number.
2. Receipt of purchase or credit card statement.
3. Original installers CORGI/Gas Safe* registration number (gas fires only).
4. Annual service receipt for every 12 months (gas fires only).
*Gas Safe Register replaced CORGI as the gas registration body in Great Britain and the Isle of Man on 1st April 2009.
F861310
A
GB IE
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifications without prior notice.
5
© 2015 Focal Point Fires plc.
Download PDF