i300 Professional Iron System

i300
Professional Iron System
Instruction Manual
USER INSTRUCTIONS
Thank you for purchasing the RELIABLE i300 series steam boiler. Please
follow the instructions carefully. With proper care and maintenance, your
steamer will provide years of dependable service.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Remove the ironing system from its packing and make sure all packing
parts have been taken off (including the protection bags). Lay the
product on a flat and steady surface fitted to support it next to a wall
socket (max. mt. 1,5).
It is recommended to lay the iron on the supplied pad.
Insert in the right seat (2) the small supplied wand to hold the hose up
and hook it with the spring up to the iron-boiler connecting wire.
Unscrew the safety cap (1) and let the internal air out. Fill the boiler
with: Max. 1,1 litres of water for model i300
Use the funnel supplied, making sure you do not overfill the tank.
Insert the plug into the main supply point; switch on boiler (4) and iron
button (3). If the two buttons come on, the iron and boiler are working.
Turn the iron plate’s temperature regulating knob (6) to the position
“cotton °°°” (indicated on the iron knob).
Wait for the boiler button’s red light (4) to turn off (it takes about 10
minutes). While ironing, the boiler button’s red light normally comes on.
The machine is ready for use.
Push the steam button (7).
In case the steam stops during ironing and the water button’s red light
(5) comes on, it means that there is not enough water in the tank. To
start ironing again, switch off the boiler button (4); press the steam iron
button (7) to ensure there is no more steam in the boiler, slowly open
the pressure cap (1) and refill to the required level with warm water.
Replace the cap and wait for it to build up pressure again.
When you first press the steam button (after having turned the boiler
on and depressed the steam button on the iron) you might notice a
decrease in pressure. This is because the tank has air in it. In order to
have plenty of steam (after you have depressed the iron) wait until the
pressure goes back up to the maximum level before you begin.
COMPONENTS
1.
2.
3.
4.
5.
6.
7.
Safety cap
Wand to hold mono-hose up
Iron button
Boiler button
Light for low water
Temperature regulating knob
Steam button
CAUTION
•
•
Do not leave the machine unattended while the plug is connected to
the socket.
The iron reaches very high temperatures and it keeps being very hot
even 15 minutes after it’s been switching off. Be careful not to burn
yourself.
•
•
•
•
For complete safety, before filling the boiler, please disconnect the
plug.
While using the machine, never unscrew or remove the cap while
under pressure (1). Before removing it, make sure that it does not
give off steam anymore by shutting the boiler off, and pressing the
steam iron button (7) to release all remaining steam.
The machine has a special heating element. Only qualified
technician should replace it.
The safety cap (1) must be replaced with original parts only.
TECHNICAL DATA
Adjustable iron thermostat set from 60°C to 200°C
Bimetallic safety iron thermostat with manual reset at 275°C
Full aluminium-plated heating element at 800W – 230V
Boiler power i300: 700W
Working pressure i300: 2,5 bar
Tank nominal capacity of model i300: 1,4 litres
TROUBLESHOOTING
PROBLEM
Does
steam go
out from
the boiler?
EXPLANATION
It may happen that, while filling the
tank, some water overfills the cap
and flows inside the boiler wetting
the insulating material
SOLUTION
In order to solve the problem, we suggest
using the machine as usual so that the
insulating material dries up in about one
hour through the heat of the machine. In
case you still have this problem after one
working hour, please contact the service
centre.
Does the
1) While filling the tank you may 1) The problem will go on until the excess
steam iron have poured too much water into it. water is emptied. Keep the steam button
leak steam
depressed until the water in the tank is at
mixed with
the correct level.
water?
2) The iron plate has to be hot 2) Please check that the temperature knob
before the steam passage
is on the right position: “cotton °°°)”
There is
1) The steam knob (where
1) Open the steam knob anticlockwise.
no steam
supplied) might be closed
coming out
of the
2) The iron switch might be off
2) After the iron switch comes on, wait for 4
iron?
minutes so that the iron plate gets hot.
3) The boiler switch might be off
3) After the boiler switch comes on, wait for
10 minutes so the boiler produces steam.
4) Fill it following the instructions carefully.
4) The water might be used up.
Does the
ironing
board get
wet?
1) The ironing board cover might
not be able to absorb the steam
completely
1) You might use a thicker cover (or two
covers) so to create a thicker surface to
absorb the steam better. In case you are
using a vacuum table, switch on the
vacuum function each time you are using
the steam
2) The steam iron leaks steam
2) See # 2
mixed with water (Check by
spraying some steam on a dry
cloth)
Does the
Some dirty might have gone into Fill the empty tank with 1 liter of water,
steam leak the tank with the water and it is screw the cap up, shake it, unscrew the
dirty
given off from the iron.
cap and empty the tank. Repeat the action
water?
until the water is cleaned. We do not
recommend the use of any additive to pour
in the tank. Before ironing again spray
some steam on a cloth until clean steam
comes out.
SPARE PARTS LISTS
ITEM CODE
AST114
DESCRIPTION
FAIRLEAD FOR HEATING ELEMENT FOR IRONING BOARD
Q.TY
2
CD338/1
NUT FOR WAND HOLDER
1
CD338/2
WASHER FOR WAND HOLDER
1
CD338/3
WAND SUPPORT
1
CD339/023
BOILER
1
CD343/700
COPPER HEATING ELEMENT V120 W700
1
CD344
SILICONE O-RING FOR THE HEATING ELEMENT
1
CD346/25
PRESSURE SWITCH SET 2,5 BAR MANUAL RESET
1
CD347
FAIRLEAD FOR CAP CONNECTION
1
CD347/023
FAIRLEAD FOR MONOHOSE
1
CD348
BULB THERMOSTAT 165°
1
CD348/1
SCREW FOR BULB THERMOSTAT
2
CD350
INDICATOR LIGHT
1
CD353
TERMINAL BLOCK PA21 4 POLES
1
CD356
NYLON MONOHOSE MT.2,2
1
CD361
CABLE BLOCK 6N3-4
1
CD363
PAD RB2000
1
CD365/4
SAFETY CAP 3/8 MALE
1
CD366/1
O-RING FOR CAP IN TEFLON
1
CD367
DYN SMALL FOOT
4
CD368
WAND FOR MONO-HOSE
1
CD368/1
SPRING FOR CORD SUPPORT
1
CD368/2
CLIP FOR SPRING
2
CD369
FUNNEL
1
CD376
MUSHROOM-SHAPED CAP FOR IRON REST
6
CD378/1
HOSE CLAMP CLIP 9/11
1
CD382/023
GLASS WOLL INSULATING
1
CD385/110
WIRING SILICONE+C.V.
1
CD467
CLIP FOR STOPPING MONOHOSE
1
CD479
LOWER CHASSIS
1
CD482
RED LIGHT
2
CD483
UPPER CHASSIS PS21CANADA
1
CD484
BRACKET TO FIX TANK
1
CD485
SOLENOID VALVE S/6000/3 120VOLT UL WITH COIL BH/G6IU
1
CD486
COPPER TUBE FOR PRESSURE SWITCH
1
CD487
CORD 110VOLT 2 PLUG 16AWG
1
CD490
BRASS NICHEL ANGLE CONNECTION
1
FS036
KNOB
1
FS002/110
IRON PLATE
1
FS003
ADJUSTABLE THERMOSTAT
1
FS004
THERMOSTAT 271 MANUAL RESET
1
FS005
CORK HANDLE
1
FS006
BRACKET FOR STEAM IRON
1
FS007
CAP FOR STEAM IRON
1
FS009
WIRING FOR STEAM IRONCABLAGGIO PER FERRO NEW_
1
FS011
INSERT FPR HANDLE 121 MM.
1
FS012
FIXING SCREW M4*22
1
FS014
BACK HANDLE SCREW
3
FS015
CLOSING SCREW
2
FS016
MICROHOLDER SCREW
1
FS017
HANDLE FIXING SCREW M5X10 ZNB
2
FS018
BLOCKING TERMINAL BLOCK SCREW
3
FS019
HANDLE COVER FOR IRON
1
FS020
SILK SCREEN PRINTING BACK HANDLE
1
FS021
BUTTONHOLDER
1
FS022
BUTTONCOVER
1
FS023
BUTTON
1
FS024
LOWER BUTTON
1
FS025
BRACKETCOVER PLAQUE
1
FS026
CABLEBLOCK
1
FS027
FRONTHANDLEHOLDER
1
FS028
BACKHANDLEHOLDER
1
FS030
SCREWCOVER CAP
2
FS031
BRASS WAHSER-SPACER
2
FS032
BRASS SPACER
2
FS033
MICRON
1
FS035
HANDLETIGHTING SCREW
4
FS038
WASHER UNDER HANDLE
2
FS039
WASHERUNDER KNOB
1
FS041
FAIRLEAD FOR CURRENT CORD
1
GV025/23
NUT 4MA 5588 ZNB
3
GV025/27
WASHER FOR FEET
3
GV028/30
"L" JOINT FOR SOLENOID WITH OGIVA
1
GV028/31
"L" JOINT FOR MONOMTER WITH OGIVA
1
GV028/52
FRONT SCREW
MC023
BUD
2
MC130
SWITCH
2
MC131
SUPPORT FOR OVAL SWITCH
2
MC132
CHROME OVAL BUTTON
2
RIC003
TERMINAL BLOCK 4 POLES
1
10
i300 PARTS DRAWING
RELIABLE PRODUCTS WARRANTY
LIMITED 1 YEAR WARRANTY
For a period of one year from date of purchase we will, free of charge,
repair defects in material or workmanship which appear in the mechanical
or electrical parts of all RELIABLE™ brand products excluding all wear and
tear components.
Wear and Tear Component List:
Steam Equipment: Press pad and cover, Teflon® seals, Teflon® shoe,
steam-electric hoses
Sewing Equipment: Hooks, loopers, stitch plates, feed dogs, needles,
motor clutch disc, brushes, fuse
Cloth Cutting Equipment: Blades, stones, sharpening bands, shoe
Halogen Lights: Bulbs
LIMITED 90-DAY WARRANTY ON ALL PARTS AND ADJUSTMENTS
For a period of 90 days from date of purchase we will, free of charge, provide required adjustments and repairs to your RELIABLE™ product.
Warranty service is available by returning the product with this warranty
document and proof of purchase to your nearest authorized RELIABLE™
service center.
This limited warranty is in effect provided that your machine is used for
normal purposes for which it was intended, and is given reasonable good
care and maintenance in accordance with the instructions contained in the
instruction booklet.
Your authorized dealer (or Reliable Corporation) will not be held responsible for damage if the machine has been repaired by an unauthorized
dealer.
These warranties give you specific legal rights and you may have other
rights, which vary from province/state to province/state.
If you have any questions regarding these warranties, you may write to:
RELIABLE CORPORATION
100 WINGOLD AVENUE, UNIT 5
TORONTO, ONTARIO M6B 4K7
CANADA
www.reliablecorporation.com
Download PDF