Countertop and Freestanding Ice and Water Dispenser

Countertop and Freestanding Ice and Water
Dispenser with Chewblet® Ice Machine
_7CI100A, _7FS100A, _15CI100A, _15FS100A
230 V/50 Hz and 220 V/60 Hz
Installation, Operation and Service Manual
Serial numbers above E01087
_7FS100A
_7CI100A
_15FS100A
_15CI100A
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Order parts online:
www.follettice.com
00976738R06
Contents
Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ambient Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Refrigeration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Heat Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
_7 Series Detailed Drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
_15 Series Detailed Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Countertop Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Freestanding Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance/Cleaning Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessing Internal Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Filter Display Indicator Activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NSF-approved Cleaning and Sanitizing Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LED Indicator Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Evaporator Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Evaporator Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Water Feed Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Bin Melt Water/Evaporator Feed/Clean Out System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Vent System Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Refrigeration Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Condenser Fan Motor Removal (_7 Series Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
User Interface Display Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Electrical Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
_7 Series Exterior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
_7 Series Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
_15 Series Exterior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
_15 Series Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
_7 Series Bin Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
_15 Series Bin Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Evaporator Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Base Stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Welcome–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability, and outstanding
after-the-sale support. To ensure that this product delivers that same degree of service, we ask that you take a
moment to review this manual before beginning the installation. Should you have any questions or require technical
help at any point, please call our technical service group at (877) 612-5086 or +1 (610) 252-7301.
Before You Begin––––––––––––––––––––––––––––––––––––––––––––––––––––
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage
is found, immediately notify the shipper and contact Follett Corporation so that we can help in the filing of a claim,
if necessary. If needed, the serial number of your dispenser can be found by removing the drip tray ❶ and locating
the serial number label ❷. A QR Code is located on the right hand side of the drip tray ❸. This code allows you to
access manuals, technical bulletins, and on-line training related to the 7 Series and 15 Series dispensers.
2
1
3
Check your paperwork to verify that you received the correct dispenser. Follett configuration numbers are designed
to provide information about the type of dispenser you are receiving. The following is an explanation of the different
model numbers.
E
Electrical
E 230 V/50 Hz
C 220 V/60 Hz
7
Dispenser Storage Capacity
7
7 lb (3.1 kg)
15 15 lb (6.8 kg)
CI
100
Configuration
Ice Machine Capacity
CI Countertop
100 lb (45.3 kg) per day
FS Freestanding
A
Condenser Type
A Air-cooled
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz3
Important Safety Information––––––––––––––––––––––––––––––––––––––––––
Please read and adhere to the following safety information while installing, using, or servicing your Follett Ice
Dispenser.
1. Always disconnect power before servicing the dispenser.
2. Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.
3. Ice is food. Follow the recommended cleaning and sanitizing instructions to maintain cleanliness of
delivered ice.
4. The appliance is not intended for use by persons including children with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervised or
instruction concerning use of the appliance by a responsible person for their safety. Children should be
supervised to ensure that they do not play with the appliance.
Specifications––––––––––––––––––––––––––––––––––––––––––––––––––––––
Dimensions
_7CI100A
_7FS100A
_15CI100A
_15FS100A
Width
40 cm (14.50")
40 cm (14.50")
40 cm (14.50")
40 cm (14.50")
Depth
56.2 cm (22.12")
56.2 cm (22.12")
59.7 cm (23.50")
59.7 cm (23.50")
Height
44.5 cm (17.50")
106.4 cm (41.88")
57.2 cm (22.50")
118.7 cm (46.75")
Unit Shipping Weight
41 kg (90 lb)
54.4 kg (120 lb)
45.4 kg (100 lb)
60 kg (130 lb)
Ambient Information
CAUTION!
The _7CI100A, _7FS100A and _15CI100A, _15FS100A are for indoor use only.
Designed for commercial use. Follett is not able to provide in-house services
for residential installations.
Maximum*
Minimum*
Air Temperature
38 C (100 F)
10 C (50 F)
Water Temperature
32.2 C (90 F)
4.5 C (40 F)
Water Pressure
70 psi (483 kpa)
69 kpa (10 psi)
†
Relative Humidity
55% at 25.5 (78 F)
* Use outside of these limitations is misuse and will void warranty.
† Best performance is achieved between 27 C (80 F) and 10 C (50 F).
Plumbing
§§ Water Inlet: 1/4" MPT
§§ Optional Drain Accessory Kit (item# 00956375 or 00981977): 1/2" ID tubing
§§ Water shut-off recommended within 1.5 m (5 ft.) of dispenser
4
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Specifications––––––––––––––––––––––––––––––––––––––––––––––––––––––
Water
WARNING!
Connect to potable water supply only.
§§ Water Mineral Content:
–– TDS: greater than 5 ppm (mg/l) but less than 400 ppm (mg/l)
–– Hardness: Less than 200 mg/l (12 gpg)
§§ Not recommended for use with softened water
§§ Ingress Protection (IP) rating: IPX0 (no protection)
Clearances
§§ 7.62 cm (3") behind and on each side of dispenser for electrical and connection and ventilation
Electrical
§§
§§
§§
§§
§§
E Series: 230V, 50 Hz, 1 phase, 5A, maximum fuse 10A
C Series: 220 V, 60 Hz, 1 phase, 5A, maximum fuse 10A
Connect to dedicated 10A circuit, fuse or breaker.
Must be grounded - requires 3-prong outlet. Do not remove ground.
Replacement cord instructions, type IEC 60320-C13 attachment - If the supply cord is damaged, it must be
replaced by a special cord or assembly available from the manufacturer or its service agent.
Refrigeration
WARNING!
Do not damage the refrigerant circuit. Refrigerant can cause personal injury and/or damage dispenser.
§§ Refrigerant R134a – 204 grams (7.2 ounces)
Heat Rejection
§§ 498 W (1700 BTU/hr)
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz5
Specifications
(continued)–––––––––––––––––––––––––––––––––––––––––––––––
_7 Series Detailed Drawing
Countertop models
37.1 cm (14.62")
37.1 cm (14.62")
44.7 cm
(17.59")
44.7 cm
(17.59")
20.3 cm
(8.00")
56.2 cm (22.12")
6.04 cm
(2.38")
17.5 cm
(6.88")
1/4" MPT
water inlet
7.62 cm
(3.00")
Freestanding models
37.1 cm (14.62")
37.1 cm (14.62")
44.7 cm
(17.59")
44.7 cm
(17.59")
20.3 cm
(8.00")
6.04 cm
(2.38")
62 cm
(24.41")
56.2 cm (22.12")
6
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
17.5 cm
(6.88")
1/4" MPT
water inlet
7.62 cm
(3.00")
Specifications
(continued)–––––––––––––––––––––––––––––––––––––––––––––––
_15 Series Detailed Drawing
Countertop models
37.1 cm (14.62")
59.7 cm (23.50")
37.1 cm (14.62")
57.2 cm
(22.50")
57.2 cm
(22.50")
20.3 cm
(8.00")
56.2 cm (22.12")
Freestanding models
6.04 cm
(2.38")
23.50" (59.7 cm)
37.1 cm (14.62")
17.5 cm
(6.88")
1/4" MPT
water inlet
7.62 cm
(3.00")
37.1 cm (14.62")
57.2 cm
(22.50")
57.2 cm
(22.50")
20.3 cm
(8.00")
119.4 cm
(47.00")
6.10 cm
(2.40")
17.5 cm
(6.88")
1/4" MPT
water inlet
7.57 cm
(2.98")
62.2 cm
(24.50")
56.2 cm (22.12")
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz7
Installation–––––––––––––––––––––––––––––––––––––––––––––––––––––––––
CAUTION!
No service or maintenance should be performed until the technician
has thoroughly read this service manual. Except for routine cleaning
and sanitizing, only qualified technicians should attempt to service
or maintain this equipment.
Countertop Installation
Fig. 1 The _7 Series countertop model is designed to fit on counters underneath
standard mounted cabinets, this does not apply to _15 Series models. See
page 4 for dimensions. Installation instructions for freestanding model
may be found on page 9.
countertop models
minimum 77 mm (3")
clearance required
1. A clearance of at least 7.62 cm (3") is required behind and on
each side of the dispenser for electrical connection and ventilation
(Fig. 1).
2. Rough-in the electrical service and water line.
§§ Electrical: 230V, single phase. The dispenser is provided with a 2.4 m
(8 ft.) power cord with choice of CEE 7/7, AS 3112, or BS 1363 plug.
§§ Water: supply line (with shut-off valve) connects to the dispenser's
1/4" MPT inlet.
NOTICE!
If installing optional Drip Tray Drain Kit or Leg Accessory,
complete those steps before proceeding. Refer to instructions
included with the Drip Tray Drain Kit, or see page 9 for Leg
Accessory instructions.
3. Connect water line. Recommended routing (Fig. 2) allows easy access
to water for cleaning and sanitizing procedure.
4. If installing the optional internal water filter*, please see
Maintenance/Cleaning Mode on page 12 before proceeding. If
not, proceed to step 5.
* If your dispenser has the internal water filter option, the water filter must be
installed for the dispenser to operate. Because internal components will need to
be accessed for both procedures, Follett recommends installing the water filter
just prior to initial sanitizing.
Fig. 2 91.4 cm (3')
Plug
Valve
5. Connect power supply.
6. Sanitize the dispenser prior to use (see the Initial Sanitizing Kit
instructions shipped with this unit).
1/4" MPT
8
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Installation
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––
Optional Leg Accessory Installation
Fig. 3 CAUTION!
Use caution when tipping the dispenser during leg installation. Do
not lay unit on back or side. DO NOT EXCEED 30° angle. Tipping
more than 30° can result in compressor malfunction.
1. If installing optional 4" Leg Accessory (item# 00956300), place a
12.7 cm (5") spacer underneath the dispenser to ease installation.
2. Remove four plastic, thread-protecting plugs from bottom of
dispenser.
12.7 cm (5")
min.
spacer
3. Screw each leg into chassis (Fig. 3).
Freestanding Installation
Fig. 4 Installation instructions for countertop model may be found on Countertop
Installation on page 8.
1. A clearance of at least 3" (7.62 cm) is required behind and on
each side of the dispenser for electrical connection and ventilation
(Fig. 4).
freestanding models
minimum 77 mm (3")
clearance required
2. Rough-in the electrical service and water line.
§§ Electrical: 230V, single phase. The dispenser is provided with an 2.4 m
(8 ft.) power cord with choice of CEE 7/7, AS 3112, or BS 1363 plug.
§§ Water: supply line (with shut-off valve) connects to the dispenser's 1/4"
MPT inlet.
NOTICE!
If installing optional Leg Accessory, complete those steps before
proceeding. See page 11 for Leg Accessory instructions.
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz9
Installation
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––
3. Remove four plastic, thread-protecting plugs from bottom of
dispenser.
Fig. 5 4. Attach dispenser to base stand with supplied hardware (Fig. 5).
NOTICE!
If installing optional Drip Tray Drain Kit, refer to instructions
included with the Drip Tray Drain Kit.
X4
5. Connect water line. Recommended routing (Fig. 6) allows easy access
to water for cleaning and sanitizing procedure.
6. If installing the optional internal water filter*, please see Optional
Internal Water Filter Installation on page 11 before proceeding.
If not, proceed to step 7.
* If your dispenser has the internal water filter option, the water filter must be
installed for the dispenser to operate. Because internal components will need to
be accessed for both procedures, Follett recommends installing the water filter
just prior to initial sanitizing.
Fig. 6 91.4 cm (3')
Plug
Valve
7. Connect power supply.
8. Sanitize the dispenser prior to use (see the Initial Sanitizing Kit
instructions shipped with this unit).
1/4" MPT
10
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Installation
(continued) ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
9. Secure unit to wall or cove molding with supplied bracket (Fig. 7) to
prevent tipping.
Fig. 7 Note: Fasteners must be supplied by installer.
WARNING!
Freestanding unit must be secured to wall to prevent tipping.
Failure to do could result in personal injury or damage to the
unit.
Optional Leg Accessory Installation
1. If installing optional 6" Leg Accessory (item# 00956318), tilt or lay
base stand on side and screw each leg into stand (Fig. 8).
Fig. 8 Fig. 9 Optional Internal Water Filter Installation
If your dispenser has the internal water filter option, the water filter must be
installed for the dispenser to operate. Because internal components will need
to be accessed for both procedures, Follett recommends installing the water
filter just prior to initial sanitizing.
1. If installing the optional internal water filter, please complete the
steps shown in Accessing Internal Components on page 12
before proceeding.
1
2
2. Lift and remove the top panel, set aside (Fig. 9.1).
3. Remove two screws (Fig. 9.2) and remove left side panel.
4. Install filter as shown. Turn filter clockwise until it is fully seated
(Fig. 9.3).
3
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz11
Maintenance/Cleaning Mode––––––––––––––––––––––––––––––––––––––––––
Fig. 10
Cleaning Mode (Dispensing Disabled) - Use when cleaning surface
Entering Cleaning Mode disables the User Interface and allows you to clean
the outside of the dispenser without accidentally dispensing water or ice.
2
1. To enter Cleaning Mode, press and immediately release the
maintenanc_lean switch (Fig. 10.1) so that only "FRESH FILTERED
ICE AND WATER" displays in the user interface (Fig. 10.2).
2. To exit Cleaning Mode, press and immediately release the
maintenanc_lean switch so that the ice and water icons also display
in the user interface.
1
Maintenance Mode (All Operations Disabled) - Use when cleaning ice
machine
Entering Maintenance Mode disables all operations and allows you to safely
clean and/or sanitize the icemaker and dispenser.
1. To enter Maintenance Mode, press and hold the maintenanc_
lean switch (Fig. 10.3) until
displays in the user interface
(Fig. 10.4).
4
2. To exit Maintenance Mode, press and hold the maintenanc_lean
switch until
no longer displays in the user interface.
3
Note: Entering and exiting Maintenance Mode will reset the six-month
periodic maintenance reminder.
Accessing Internal Components–––––––––––––––––––––––––––––––––––––––
CAUTION!
Fig. 11 Except for routine cleaning and sanitizing, only qualified
technicians should attempt to service or maintain this equipment.
1. Press and hold the maintenanc_lean switch (Fig. 10.1) until
displays in the user interface (Fig. 10.2).
2. Remove (unscrew) chrome ice dispenser chute (Fig. 11.1).
1
3. Remove the drip tray (Fig. 11.2).
4. Remove the two screws (Fig. 11.3) on the front panel (behind the
drip tray).
5. Remove and set aside the front panel (Fig. 11.4) - do not
disengage the plug on the back of the User Interface or the
tubing at the water dispenser chute (if so equipped).
3
2
4
12
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Filter Display Indicator Activation––––––––––––––––––––––––––––––––––––––
If you purchased your dispenser with a Follett filter, the filter display indicator Fig. 12 activation has been preset at the factory.
If you are using an “after market filter,” an adjustment may be made to
activate the “Fresh Filtered Ice & Water” display.
1
Activating “Fresh Filtered Ice & Water”
1. Remove the front panel as explained in Accessing Internal
Components on page 12 then refer to Fig. 12.
2. Remove top panel (Fig. 12.1).
Note: For _15 Series dispensers, the right side panel must also be
removed.
3. Remove (1) screw and top of control board enclosure (Fig. 12.2).
4. Locate the DIP switches on the dispenser's control board (Fig. 13).
Use a fine-pointed object to move the “Filter” DIP switch (DIP switch
#3) to the ON position.
Deactivating the Six-Month Maintenance/Filter Change Reminder
1. Use a fine-pointed object to move the “PM” DIP switch (DIP switch
#8) to the ON position.
2
OFF
2
3
Ice & water
Internal filter supplied or to display "Fresh Filtered"
4
5
6
30 minute delay
7
8
1
Not used (OFF position)
Ice only
No internal filter
Not used (OFF position)
Not used (OFF position)
15 minute delay
Not used (OFF position)
Six-month PM enabled
Fig. 13
ON
Six-month PM disabled
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz13
NSF-approved Cleaning and Sanitizing Procedure––––––––––––––––––––––––
Cleaning and sanitizing should be performed at least every 6 months (more often
if local water conditions dictate).
Fig. 14
WARNING!
1
§§ Place the dispenser in Maintenance Mode prior to servicing or
cleaning the ice machine. See Maintenance/Cleaning Mode on
page 12.
§§ For protection, rubber gloves and safety goggles (and/or face shield)
should be worn when handling SafeCLEAN Plus™.
§§ Do not use bleach, it will damage the dispenser.
Required Supplies
§§ _7 Series: 0.621 L (21 oz.) or 3 packets SafeCLEAN Plus
_15 Series: 1.24 L (42 oz.) or 6 packets SafeCLEAN Plus
§§ Funnel and Bucket
Ice machine and Dispenser
1. Dispense all the ice out of the unit.
2. Press and hold maintenanc_lean switch until
interface to enter Maintenance Mode.
3
2
4
displays in the user
3. Remove (unscrew) chrome ice dispense chute (Fig. 14.1).
4. Remove drip tray (Fig. 14.2).
5. Remove (2) screws located behind the drip tray (Fig. 14.3).
6
6. Move front panel and place on top or beside unit (Fig. 14.4).
7. Remove plug cap from the end of drain tube (Fig. 14.5) and lower tube
to drain water into bucket. After the system has been drained of water
replace plug cap in drain tube.
8. Secure tube in holder.
7
5
9. Remove cap from bin lid cover (Fig. 14.6).
10. Screw bin lid cover cap onto ice discharge chute (Fig. 14.7).
11. _7 Series: Mix 0.621 L (21 oz.) or 3 packets SafeCLEAN Plus with 11.4 L (3 gallons) of water.
_15 Series: Mix 1.24 L (42 oz.) or 6 packets SafeCLEAN Plus with 22.7 L (6 gallons) of water
12.Pour cleaning solution into bin lid access spout until solution reaches the spout neck.
13.Allow the solution to remain in unit for 15 minutes.
14.While machine is cleaning, remove top and right side panel to access and clean air-cooled condenser.
15. Submerge ice dispense chute in the remainder of solution for 2 minutes. Rinse with clean, potable water.
16.Drain system by lowering drain tube into bucket.
17. Secure drain tube into holder.
18.Fill and drain three times with potable water. Secure drain tube.
19.Place a bucket under the dispense chute and remove cap. Note: Some solution will remain and drain out
when cap is removed. Reposition cap on bin lid spout.
20.Reinstall front panel, ice dispense chute, and drip tray.
21. Press and hold maintenanc_lean switch to exit Maintenance Mode.
14
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
NSF-approved Cleaning and Sanitizing Procedure
(continued)–––––––––––––––––
User Interface and Exterior Cabinet
1. Press and release maintenanc_lean switch so that only "FRESH FILTERED ICE AND WATER" displays
in the user interface to enter Cleaning Mode (and disable dispensing).
2. Plastic parts, including the user interface, can be cleaned with a non-abrasive glass cleaner. Clean
stainless steel panels with stainless steel cleaner.
3. Press and release maintenanc_lean switch to put unit back into service.
Service––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
LED Indicator Description
The LED Indicator is located behind the front panel.
LED Name
Clean
LED Color
Power ON
Low bin
Making ice
Sleep cycle
Time delay
Low water
Maint
Service
HI amps
HI press
Water leak
Drip tray
PM
Clean
Fig. 15 Description
Green
The dispenser is in Cleaning Mode. Dispenser is disabled to allow for cleaning of front panel.
See Maintenance/Cleaning Mode on page 12.
N/A
Not used.
PM
Red
Six-month periodic maintenance required.
Drip tray
Red
Drip tray full.
Water leak
Red
Internal leak in dispenser.
High amps
Red
Auger gearmotor has exceeded 0.55A. The HI amps and Time delay LEDs will illuminate,
the machine will shut down for one hour, the LEDs will turn off, and the machine will resume
normal operation.
Service
Red
8000 hour bushing check (call Follett technical service group at (877) 612-5086 or
+1 (610) 252-7301).
Maintenance
Yellow
Enter Maintenance Mode by pressing and holding maintenanc_lean switch for 5 seconds. Unit
will not make or dispense ice.
Low water
Yellow
Insufficient water supply to machine or no low bin LED upon startup.
Time delay
Yellow
Ice production will not resume for at least 15 minutes after a full bin is achieved and a
minimum amount of dispense activity has elapsed.
Sleep cycle
Green
After a full bin and 10 minutes of non-use, the unit goes into standby and will not produce ice
until either:
_7 Series:12 hours has elapsed, _15 Series: 4 hours has elapsed
or ice or water has dispensed.
Making ice
Green
Gearmotor, compressor, and fan motor energized.
Low bin
Green
Bin switch closed calling for ice.
Power on
Green
Power supplied to unit.
—
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz15
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Evaporator Disassembly
Fig. 16
1. Disconnect power from the dispenser.
2. Turn off water supply to dispenser.
2
3. Remove (unscrew) chrome ice dispenser chute
(Fig. 16.1).
4. Remove the drip tray (Fig. 16.2).
1
5. Remove the two screws (Fig. 16.3) on the front panel
(behind the drip tray).
6. Remove and set aside the front panel (Fig. 16.4) - do not
disengage the plug on the back of the User Interface.
7. Lift and remove the top panel, set aside (Fig. 16.5).
8. Remove two screws (Fig. 16.6) and remove left side
panel.
1
9. Remove two screws (Fig. 16.7) and remove right side
panel.
3
2
4
6
5
7
16
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
10. Unplug the gear motor (three connectors) (Fig. 16).
Fig. 17 11. Remove ground screw connection.
12. Remove gear motor:
Fig. 18 §§ Remove M6 allen screw, retainer, spacer and key (Fig. 18.1).
§§ Remove two M6x90 allen screws (Fig. 18.2).
§§ Pull gear motor from auger (Fig. 18.3).
§§ Remove main housing insulation (Fig. 18.4).
13. Remove all traces of petro-gel from auger shaft.
4
2
3
1
2
14. Remove compression nozzle:
Fig. 19 §§ Loosen hose clamp (Fig. 19.1).
§§ Remove transport tube (Fig. 19.2).
1
2
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz17
Service
(continued)––––––––––––––––––––––––––––––––––––––––––––––––––––
15. Remove M6 socket head allen screw (Fig. 20.1).
Fig. 20 16. Remove compression nozzle retainer (Fig. 20.2).
1
17. Remove compression nozzle (Fig. 20.3).
2
3
18. Remove main housing:
Fig. 21 §§ Disconnect vent line from T fitting (Fig. 21.1).
1
19. Remove three M6x25 socket head allen screws
(Fig. 22.1).
Fig. 22 20. Remove main housing (Fig. 22.2).
2
1
18
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Service
(continued)––––––––––––––––––––––––––––––––––––––––––––––––––––
21. Remove and discard mating ring and seal (Fig. 23.1).
Fig. 23 22. Carefully remove auger (Fig. 23.2).
WARNING!
Use caution when removing auger. The auger is very
sharp - handle with care to avoid personal injury.
2
1
Evaporator Assembly
Fig. 24 1. Remove and inspect main housing O-ring seal. Replace if
damaged in any way.
2. Clean O-ring groove. Lubricate O-ring with Petro-gel and
reinstall.
3. Use cardboard disc to press new mating ring into main
housing (Fig. 24.1).
4. Lube the shaft with liquid soap in the area shown
(Fig. 24.2) and slip on seal and spring (Fig. 24.3).
Note: Do not touch the sealing surfaces with bare hands.
Contact with bare skin will cause premature seal failure.
5. Install auger (Fig. 24.4).
1
Cardboard
disc
Do NOT
touch!
2
4
3
6. Install main housing:
Fig. 25 §§ Slide main housing onto auger shaft (Fig. 25.1).
§§ Install three M6x25 allen screws (Fig. 25.2).
§§ Connect vent line to T fitting (Fig. 25.3).
3
1
2
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz19
Service
(continued)––––––––––––––––––––––––––––––––––––––––––––––––––––
7. Install compression nozzle:
Fig. 26 §§ Remove and inspect compression nozzle O-ring seal.
Replace if damaged in any way.
§§ Clean O-ring groove. Lubricate O-ring with Petro-gel and
reinstall.
§§ Install compression nozzle (Fig. 26.1).
§§ Install compression nozzle retainer (Fig. 26.2).
§§ Install M6 socket head allen screw (Fig. 26.3).
3
2
1
8. Install transport tube (Fig. 27.1).
Fig. 27 9. Tighten hose clamp (Fig. 27.2).
2
1
10. Install gear motor:
Fig. 28 §§ Install main housing insulation (Fig. 28.1).
§§ Slide gear motor onto auger shaft (Fig. 28.2).
§§ Install two M6x90 allen screws (Fig. 28.3).
1
3
2
3
20
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Service
(continued)––––––––––––––––––––––––––––––––––––––––––––––––––––
11. Use screwdriver to orient auger shaft to align with motor
shaft keyway (Fig. 29.1).
Fig. 29 12. Install key into keyway (Fig. 29.2).
2
1
13. Install spacer, ensure that key is captured in slot
(Fig. 30.1)
Fig. 30 1
14. Insert screwdriver into groove of auger shaft and pry shaft
outwards (Fig. 31.1).
Fig. 31 15. Insert retainer into groove (Fig. 31.2), ensure that retainer
is aligned with hole in spacer.
1
2
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz21
Service
(continued)––––––––––––––––––––––––––––––––––––––––––––––––––––
16. Install screw and tighten (Fig. 32.1).
Fig. 32 1
2
17. Plug in gear motor (Fig. 33).
§§
§§
§§
§§
22
PINK to BLUE
BLACK to BLACK
GREY to WHITE
Connect ground wire with ground screw.
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Fig. 33 PI
BL NK to
AC
B
GR K to LUE
EY BLA
to
WH CK
ITE
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Water Feed Schematic
Evaporator
Float
Water Chute
(optional)
Filter (optional)
Water Solenoid Valve
(optional)
Water Solenoid Valve
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz23
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Bin Melt Water/Evaporator Feed/Clean Out System Schematic
Storage Bin
Vent System Schematic
Storage Bin
Vent Tube
Reservoir
24
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Refrigeration Schematic
CONDENSER
FILTER-DRIER
CAP TUBE
COMPRESSOR
EVAPORATOR
ACCUMULATOR
HIGH PRESSURE VAPOR
LOW PRESSURE LIQUID
HIGH PRESSURE LIQUID
LOW PRESSURE VAPOR
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz25
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Condenser Fan Motor Removal (_7 Series Shown)
26
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
User Interface Display Identification
Operation Display
Condition
Procedure
Normal
operation
­—
Cleaning Mode
Press and release maintenanc_lean
switch to clean the user interface
without dispensing ice or water (see
Maintenance/Cleaning Mode on page
12).
Drip tray full
Empty drip tray.
Six-month
periodic
maintenance
required
Follow Maintenance Mode procedure
(below) and also see NSF-approved
Cleaning and Sanitizing Procedure on
page 14.
Maintenance
Mode
Enter Maintenance Mode by pressing
maintenanc_lean switch until
displays. Complete the cleaning and
sanitizing procedure shown on page
14 and change the filter, if so
equipped. Exit Maintenance Mode by
pressing and holding maintenanc_lean
switch until
no longer displays.
Service 8000 hr
bushing check
Call Follett Technical Service Group at
(877) 612-5086 or +1 (610) 252-7301.
The flashing wrench indicates that the
8000 hr bushing check is required.
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz27
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Service Display
Condition
High amps
Procedure
Contact Follett technical service
group at (877) 612-5086 or
+1 (610) 252-7301.
Note: For dispensers after serial
number D45191, the phone
and wrench will not be
illuminated.
28
Internal leak in
dispenser
Locate leak and repair - Press reset
on control board. Contact Follett if
icemaker is leaking.
Sleep mode
Press either dispense button to
return to normal operation.
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
N
POWER L1
GND
WHITE
#17
WHITE/
GRAY
BLACK
GRN-YEL
#11
BLACK
BLUE/
PINK
GRN-YEL
#4
AUGER
FAN
BLACK
BLACK
#8
BLUE
#7
BLACK
#15
GRN-YEL
WATER DISPENSE VALVE
WHITE
BLACK
#18
#10
BLACK
#14
DISP.
#12
FAILSAFE SOLENOID VALVE
WHITE
#16
WHITE
P1
L1
L1
L1
P3
P19
P20
P21
FAN
ICE DISP
P6
BLUE
#5
N
N
AUGER
CAP
D21
D22
N
D19
K5
CO2
K2
#13
FS
K4
K6
K7
D20
D17
WD
N
N
N
T2
CURRENT SENS
N
K3
D18
N
N
P5
RESERVOIR
WATER SENSOR
DRIP TRAY WATER
SENSOR
CHASSIS
WATER SENSOR
P4
P2
AUGER
GRN-YEL
#19
UV LIGHT
UV ON
D37
#20
#2
S2
P10
SERIAL COMM
HI PRS
P14
P16
WATER AUX
START
RELAY
P17
WATER LEVELS
BIN
P12 BIN
P12 BIN P11 CLEAN SAFE
P15
ICE AUX
P17
WATER LEVELS
YELLOW
ORANGE
BLACK
P18
T1
BLACK
WHITE
S
R
O.L.
K1
BLACK
#1
P7
RESET
S1
MAINT.
CLEAN
P11 CLEAN SAFE
P7
P8 RS485
RS485 UI
6
2
5
1
PROGRAM
P9
MODEL SELECT
GRN-YEL
C
#3
COMP.
P13 SPARE CTS
D16
COMPRESSOR
D1
CLEAN
POWER
LOW BIN
MAKING ICE
SLEEP CYCLE
TIME DELAY
LOW WATER
MAINTENANCE
SERVICE
HI AMPS
HI PRESSURE
WATER LEAK
DRIP TRAY
PM
USER
INTERFACE
RS485 UI
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
Service
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––
Electrical Wiring Diagram
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz29
Parts––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
_7 Series Exterior
6
4
7
8 x4
8 x2
8 x2
5
2
1
30
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
3
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Exterior
Reference #
Description
Part #
1
Drip Tray Assy
00957613
2
Panel, Front Assy - Includes Water Nozzle and Plug
00957621
3
Chute, Water (water option)
00957688
4
Panel, Left
00932806
5
Panel, Right
00932798
6
Panel, Top
00957654
7
Panel, Rear
00974873
8
Screw, M5 x 12 Phillips
00931931
Not Shown
_7 Series Packaging for Returns, Dispenser
00957993
Not Shown
Fitting, Elbow - 1/4" FPT x 1/4" Tube
00974261
Not Shown
Drip Tray Drain Kit
00956375
Not Shown
Drip Tray Drain Kit with 4" legs
00981977
Not Shown
Covers, Agion, User Interface
00969030
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz31
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
_7 Series Interior
4
7
13
6
1
12
2
3
5
11
10
9
10
8
32
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Interior
Reference #
Description
Part #
1
Valve, Dispense Solenoid (water option)
00968917
2
Switch, Cleaning
00957712
3
Drain/Feed Tube with Cap
00957720
4
Valve, Failsafe Solenoid
00968925
5
Compressor with Mounting Hardware (230 V/50 Hz)
00968933
5
Compressor with Mounting Hardware (220 V/60 Hz)
01062314
6
Condenser
00958017
7
Condenser Fan and Cord
00968941
8
Control Board with Stand-offs
00969048
9
Capacitor, Gearmotor
00968958
10
Sensor, Retainer Hardware Kit
00958066
11
Relay and Overload (230 V/50 Hz)
00968966
11
Relay and Overload (220 V/60 Hz)
01065143
12
Refrigeration, Piping Assy
00958132
13
Power Input
00968974
Not Shown
Cord, Power IEC60320-C13 to BS 1363
00976753
Not Shown
Cord, Power IEC60320-C13 to AS 3112
00976761
Not Shown
Cord, Power IEC60320-C13 to CEE 7/7
00976779
Not Shown
Cord, Power IEC60320-C13 to NBR 14136
01063320
Not Shown
Cord, Power IEC60320-C13 to KSC 8305
01063338
Not Shown
Cord, Power IEC60320-C13 to NEMA 5-15
01063346
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz33
Parts––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
_15 Series Exterior
6
7
4
8 x2
8 x6
8 x2
5
2
1
34
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
3
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Exterior
Reference #
Description
Part #
1
Drip Tray Assy
00957613
2
Panel, Front Assy - Includes Water Nozzle and Plug
01036425
3
Chute, Water (water option)
00957688
4
Panel, Left
01026343
5
Panel, Right
01026335
6
Panel, Top
01054733
7
Panel, Rear
01047729
8
Screw, M5 x 12 Phillips
00931931
Not Shown
_15 Series Packaging for Returns, Dispenser
01054634
Not Shown
Fitting, Elbow - 1/4" FPT x 1/4" Tube
00974261
Not Shown
Drip Tray Drain Kit
00956375
Not Shown
Drip Tray Drain Kit with 4" legs
00981977
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz35
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
_15 Series Interior
4
7
1
6
12
2
3
5
11
10
9
8
36
10
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Interior
Reference #
Description
Part #
1
Valve, Dispense Solenoid (water option)
00968917
2
Switch, Cleaning
00957712
3
Drain/Feed Tube with Cap
00957720
4
Valve, Failsafe Solenoid
00968925
5
Compressor with Mounting Hardware (230 V/50 Hz)
00968933
5
Compressor with Mounting Hardware (220 V/60 Hz)
01062314
6
Condenser
00958017
7
Condenser Fan and Cord
00968941
8
Control Board with Stand-offs
01051986
9
Capacitor, Gearmotor
00968958
10
Sensor, Retainer Hardware Kit
00958066
11
Relay and Overload (230 V/50 Hz)
00968966
11
Relay and Overload (220 V/60 Hz)
01065143
12
Refrigeration, Piping Assy
00958132
13
Power Input
00968974
Not Shown
Cord, Power IEC60320-C13 to BS 1363
00976753
Not Shown
Cord, Power IEC60320-C13 to AS 3112
00976761
Not Shown
Cord, Power IEC60320-C13 to CEE 7/7
00976779
Not Shown
Cord, Power IEC60320-C13 to NBR 14136
01063320
Not Shown
Cord, Power IEC60320-C13 to KSC 8305
01063338
Not Shown
Cord, Power IEC60320-C13 to NEMA 5-15
01063346
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz37
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
_7 Series Bin Assembly
9
3
4
5
6
2
1
7
8
38
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
_7 Series Bin Assembly
Reference #
Description
Part #
1
Ice Chute Assembly
00957670
2
Ice Transport Tubing with Insulation
00957746
3
Switch, Shuttle
00957753
4
Shuttle, Complete Assy
00957761
5
Lid, Bin Assy
00957779
6
Bin, Assy
00957787
7
Auger, Dispense
00931113
8
Motor, Dispense
00968982
9
Cap and Insulation, Bin
00957936
Not Shown
For serial numbers D17619 and below:
Bin Cap
00931519
Ice Chute
00927210
Chute Adapter
00926550
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz39
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
_15 Series Bin Assembly
5
6
3
4
1
7
8
2
40
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
_15 Series Bin Assembly
Reference #
Description
Part #
1
Ice Chute Assembly
01051846
2
Ice Transport Tubing with Insulation
01051960
3
Switch, Shuttle
00957753
4
Shuttle, Complete Assy
01053248
5
Lid, Bin Assy
01053255
6
Bin, Assy
01053263
7
Auger, Dispense
01026251
8
Motor, Dispense
00968982
9
Cap and Insulation, Bin
01053305
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz41
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Evaporator Assembly
10
11
12
14
13
13
2
8
5
6
1
3
7
4
9
42
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Evaporator Assembly
Reference #
Description
Part #
1
Gearmotor Assy
00968990
2
Main Housing with Front Seal and Screws
00957829
3
Screws, Main Housing
00957837
4
Auger with front seal
00957845
5
Ice Compression Nozzle Assy
00957852
6
Front Seal and O-Ring
00957860
7
Evaporator Assembly with Insulation
00957878
8
Housing, Bushing with Insulation
00957886
9
Hardware kit, Gearmotor (For serial numbers E01087 and above)
01048628
9
Hardware kit, Gearmotor (For serial numbers below E01087)
00957894
10
Reservoir and Float Complete Assy
00957902
11
Lid, Reservoir with Insulation and O-Ring
00957910
12
Float Valve
00957928
13
“T” Fitting - 1/4"
502923
14
Tubing - 1/4" (sold in 12" increments)
502079
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz43
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Base Stand
2
1
44
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Parts
(continued)–––––––––––––––––––––––––––––––––––––––––––––––––––––––
Base Stand
Reference #
Description
Part #
1
Front Panel, Base
00958108
2
Latches with Bayonets, Base
00958116
Not Shown
Tray, Base
00958124
Not Shown
Packaging for Returns, Base
00957985
Reference #
Description
Part #
Not Shown
Water filter cartridge, 5 micron
00968107
Not Shown
IMS II sanitizer concentrate, 16 oz
00979674
Not Shown
SafeCLEAN Plus, 3 pack
01054683
Not Shown
SafeCLEAN Plus, 6 pack
01054691
Not Shown
SafeCLEAN Plus, case of 24
01050863
Not Shown
6" Legs for base stand, set of 4
00956318
Not Shown
4" Legs for countertop dispenser, set of 4
00956300
Miscellaneous
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz45
46
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz
Dispenser and Ice Machine 230 V/50 Hz and 220 V/60 Hz47
SafeCLEAN Plus is a trademark of Follett Corporation.
Chewblet and Follett are registered trademarks of Follett Corporation, registered in US.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Follett Europe Polska Sp. z o.o.
Mokry Dwór 26 c • 83-021 Wiślina, Poland
00976738R06
+48 (58) 785-6140 • Fax +48 (58) 785-6159
www.folletteurope.com
© Follet Corporation 4/14