contents 1. fundamental safety warnings ............. 7 2

CONTENTS
14. MAKING CAPPUCCINO............................... 13
1. FUNDAMENTAL SAFETY WARNINGS..............7
15. DELIVERING HOT WATER........................... 14
2. IMPORTANT SAFEGUARDS...........................8
16.CLEANING................................................ 14
14.1 Cleaning the cappuccino maker after use.....14
2.1 Symbols used in these instructions................8
2.2 Designated use...............................................8
2.3 Instruction for Use..........................................8
16.1 Cleaning the machine..................................14
16.2 Cleaning the machine’s internal circuit.........14
16.3 Cleaning the coffee grounds container.........14
16.4 Cleaning the drip tray and condensate tray..15
16.5 Cleaning the inside of the coffee machine....15
16.6 Cleaning the water tank...............................15
16.7 Cleaning the coffee spouts...........................15
16.8 Cleaning the pre-ground coffee funnel........15
16.9 Cleaning the infuser.....................................15
3.INTRODUCTION...........................................8
3.1 Letters in brackets..........................................8
3.2 Troubleshooting and repairs...........................8
4.DESCRIPTION.............................................9
4.1 Description of the appliance ..........................9
4.2 Description of the touch screen......................9
4.3 Description of the accessories.........................9
17.DESCALING............................................... 15
5. BEFORE USE...............................................9
18. SETTING WATER HARDNESS....................... 16
5.1
5.2
5.3
5.4
18.1 Measuring water hardness...........................16
18.2 Setting water hardness................................16
Checking the appliance..................................9
Installing the appliance..................................9
Connecting the appliance...............................9
Setting up the appliance..............................10
19. WATER SOFTENER FILTER (*CERTAIN MODELS
ONLY)....................................................... 17
6. TURNING THE APPLIANCE ON.................... 10
19.1 Installing the filter.......................................17
19.2 Replacing the filter.......................................17
7. TURNING THE APPLIANCE OFF................... 10
20. TECHNICAL DATA....................................... 17
8. SETTING WATER HARDNESS....................... 10
21. DISPOSING OF THE APPLIANCE.................. 17
9. SETTING TEMPERATURE SECTION............... 10
22. EXPLANATION OF LIGHTS........................... 18
10.AUTO-OFF................................................. 11
23.TROUBLESHOOTING.................................. 20
11. ENERGY SAVING........................................ 11
24. ELECTRICAL CONNECTION (UK ONLY).......... 21
12. DEFAULT VALUES (RESET).......................... 11
13. MAKING COFFEE........................................ 11
13.1 Selecting the coffee taste.............................11
13.2 Selecting the quantity of coffee in the cup...11
13.3 Adjusting the coffee mill..............................12
13.4 Tips for a hotter coffee.................................12
13.5 Making coffee using coffee beans................12
13.6 Making coffee using pre-ground coffee........12
13.7 Making DOPPIO+ coffee using coffee beans ...
...................................................................13
13.8 Customising the DOPPIO+ coffee quantity...13
13.9 Making LONG coffee using coffee beans.......13
13.10Making LONG coffee using pre-ground coffee..
...................................................................13
13.11Customising the “LONG coffee” quantity.......13
6
1. FUNDAMENTAL SAFETY WARNINGS
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Designated use: this appliance is designed and made to prepare coffee and milk based
beverages and hot water. Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper use of the appliance.
• The surface of the heating element remains hot after use and the outside of the appliance may retain the heat for several minutes depending on use.
• To clean, follow the instructions in the section “14. Cleaning”.
• Cleaning and user maintenance shall not be made by children without supervision.
• Never clean by immersing the appliance in water.
• CAUTION: To prevent damage to the appliance do not use alkaline cleaning agents when
cleaning, use a soft cloth and a mild detergent
• This is an household appliance only. It is not intended to be used in: staff kitchen areas in
shops, offices and other working environments; farm houses; by clients in hotels, motels
and other residential type environments; bed and breakfast type environments.
• If the plug or cord is damaged, it must be replaced by Customer Services only to avoid all
risk.
• Appliances with removable cord: avoid splashes of water on the power cord connector or
socket at the back of the appliance.
• IMPORTANT: Models with glass surfaces: do not use the appliance if the surface is cracked.
FOR EUROPEAN MARKETS ONLY:
•This appliance can be used by children aged from 8 years and above if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. User cleaning and maintenance shall not be made by
children unless they are above 8 years old and supervised. Keep the appliance and power
cord away from children under 8 years of age.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they are supervised or have been given instruction
concerning use of the appliance in a safe way and if they understand the hazards involved.
• Children shall not play with the appliance.
7
• Always unplug the appliance when left unattended and before assembly, taking apart or
cleaning.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).
2. IMPORTANT SAFEGUARDS
2.1 Symbols used in these instructions
2.2 Designated use
This appliance is designed and made to prepare coffee and heat
drinks.
Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper
use of the appliance.
Important warnings are identified by these symbols. It is vital to
respect these warnings.
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
2.3 Instruction for Use
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Read this Instruction for Use carefully before using the appliance. Failure to follow this Instruction for Use may result in burns
or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note:
Keep this Instruction for Use. If the appliance is passed to other
persons, they must also be provided with this Instruction for
Use.
Please note:
This symbol identifies important advice or information for the
user.
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times, enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the cord as you
could damage it.
• To disconnect the appliance completely you must unplug it
from the mains socket.
• If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact Customer Services.
• Before cleaning the appliance, turn it off, unplug from the
mains socket and allow to cool.
3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuccino machine.
We hope you enjoy using your new appliance. Take a few minutes to read this Instruction for Use. This will avoid all risks and
damage to the appliance.
3.1 Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on pages 2-3.
3.2 Troubleshooting and repairs
In the event of problems, first try and resolve them by reading
the information given in the “22 Explanation of lights” and “23
Troubleshooting” sections.
If this does not resolve the problem or you require further information, you should consult Customer Services by calling the
number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in
the guarantee certificate provided with the machine.
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, the cup shelf could become
very hot.
8
4. DESCRIPTION
4.1 Description of the appliance
B13.Icon
: makes one cup of LONG coffee (when in the
settings menu: press to scroll through the various selections/
settings)
B14. Icon
: to make 2 cups of short espresso coffee
B15. Icon
: to make 1 cup of DOPPIO+ coffee
(page 3 - A )
A1. Beans container lid
A2. Pre-ground coffee funnel lid
A3. Beans container
A4. Pre-ground coffee funnel
A5.Button : turns the appliance on and off (standby)
A6. Cup shelf
A7. Cappuccino maker (removable)
A8. Hot water and steam connection nozzle
A9. Coffee spout (adjustable height)
A10. Condensate tray
A11. Cup tray
A12. Drip tray water level indicator
A13. Drip tray
A14. Coffee grounds container
A15. Main switch (ON/OFF)
A16. Infuser door
A17.Infuser
A18. Water tank
A19. Water softener filter housing
A20. Water tank lid
A21. Grinding adjustment dial
A22. Power cord
4.3 Description of the accessories
(page 2 - C)
C1. “Total Hardness Test” indicator paper
C2. Pre-ground coffee measure
C3.Descaler
C4. Water softener filter (*certain models only)
C5. Cleaning brush
5. BEFORE USE
5.1 Checking the appliance
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Longhi
Customer Services.
5.2 Installing the appliance
Important!
When you install the appliance, you should respect the following safety warnings:
• The appliance gives off heat. After positioning the appliance on the worktop, leave a space of at least 3 cm between
the surfaces of the appliance and the side and rear walls
and at least 15 cm above the coffee machine.
• Water penetrating the coffee machine could cause
damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the temperature could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
4.2 Description of the touch screen
(page 2 - B )
A number of icons on the touch screen have a double function. This
is indicated in brackets in the description.
B1. Steam/hot water dial
B2.Icon
: to make 1 cup of short espresso coffee
B3.Flashing light: the appliance is heating up
B4.Light :
- on steadily: put the grounds container back (A15)
- flashing: the grounds container needs emptying
B5.Light : fill the water tank (A18)
B6.Light : general alarm
B7.Flashing light: the appliance needs descaling
B8.Icon
: makes 2 cups of long espresso coffee
B9. Coffee taste selection dial
B10.Icon
: performs a rinse cycle (when in the settings
menu: press to exit the current programming)
B11.Icon
: makes 1 cup of long espresso coffee
B12.Icon
:
- on steadily: turns the steam function on (when
in the settings menu: press to confirm the current
programming)
-
flashing: the steam/hot water dial must be turned
(B1)
5.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only. If
the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
9
5.4 Setting up the appliance
7. TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Please note :
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the Instruction for use in the “18 Setting water
hardness” section.
Proceed as described:
1. Remove the water tank (A18- fig. 1), fill to the MAX line
with fresh water (fig. 2) then put back in the appliance.
2. Place a container with a minimum capacity of 100 ml
under the cappuccino maker (A7) (fig. 3).
3. Plug the appliance into the mains socket and press the
main switch (A15) on the side of the appliance (fig. 4).
4.The
icon (B12- fig. 5) flashes on the touch screen.
5. Turn the steam dial to the “I” position (fig. 6). Water is delivered from the cappuccino maker.
6. When delivery stops automatically, turn the steam dial
back to the “O” position.
The appliance goes off.
To reuse it, press the
button (A5 - fig. 7) again.
•
•
Danger of burns!
Durante il risciacquo, dai beccucci dell’erogatore del caffè (A9)
fuoriesce un po’ di acqua calda. Prestare Important a non venire
in contatto con spruzzi d’acqua.
• To turn the appliance off, press the button
(A5- fig.
7).
•The
light (B3) flashes on the control panel to indicate
the appliance is going off.
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• first turn the appliance off by pressing the
button
(fig. 7).
• Press the main switch (A15) on the side of the appliance
(fig. 4).
Important!
Never press the main switch while the appliance is on.
8. SETTING WATER HARDNESS
For Instruction for use on setting water hardness, see chapter
18.
Please note :
The first time you use the appliance, you need to make 4-5
cups of coffee before the appliance starts to give satisfactory results.
9. SETTING TEMPERATURE SECTION
If you want to modify the temperature of the water used to
make the coffee (low, medium, high, maximum), proceed as
follows:
1. With the appliance off (standby), but the main switch
(A15) pressed (fig. 4).
2. Press and hold the icon
(B2) until the lights and icons
on the touch screen (B) come on.
3. Press the icon
(B13) to select the required
temperature:
6. TURNING THE APPLIANCE ON
Please note!
• Before turning the appliance on, make sure the main
switch (A15) is pressed (fig. 4).
• Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
low
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
(A9) and is collected in the drip tray (A13) underneath. Avoid
contact with splashes of water.
• To turn the appliance on, press the button
(A5-fig.
7): the light
(B3) flashes while the appliance is heating
up and performing an automatic rinse cycle. By circulating
hot water, the appliance heats both the boiler and the internal circuits.
The appliance is at temperature when the light goes off and
the coffee lights come on.
medium
high
maximum
4. Press the
icon (B12) to confirm (or
(B10) to exit
without making the modification). The lights/icons go off.
The temperature is now programmed.
10
10. AUTO-OFF
2. Press and hold the icon
(B15) until the icons on the
touch screen (B) come on.
3. Press the icon
(B12) to reset the default values (or
(B10) to exit without making the modification). The
icons go off.
The settings and quantities have been reset to the default
values.
The time can be changed so that the appliance switches off after
being idle for 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-set Auto-off, proceed as follows:
1. With the appliance off (standby), but the main switch
(A15) pressed (fig. 4).
2. Press and hold the icon
(B8) until the lights and
icons on the touch screen (B) come on.
3. Press the icon
(B13) to select the required time:
13. MAKING COFFEE
13.1 Selecting the coffee taste
15 min.
Turn the coffee taste selection dial (B9) to set the required taste.
Turning it clockwise increases the quantity of coffee beans the
appliance will grind and therefore the strength of the coffee obtained. Turn the dial to MIN for an extra mild coffee and to MAX
for an extra strong coffee.
30 min.
1 hour
2 hours
3 hours
4. Press the
icon (B12) to confirm (or
(B10) to
exit without making the modification). The lights/icons go
off.
The auto-off time is now programmed.
Please note :
The first time you use the appliance, you will need to make
a number of coffees to identify the correct dial position
through trial and error.
• Do not turn the dial too far towards MAX, otherwise the
coffee may be delivered too slowly (a drop at a time), particularly when making two cups of coffee at the same time.
•
11. ENERGY SAVING
Use this function to enable or disable energy saving. This mode
is active by default, reducing energy consumption while the machine is on in compliance with current European regulations. To
change the setting, proceed as follows:
1. With the appliance off (standby), but the main switch
(A15) pressed (fig. 4).
2. Press and hold the icon
(B13) until the icons and
light
(B3) (if energy saving is enabled) come on.
3. Press the icon
again to enable (the light
-B3) or
disable (the light goes off) energy saving.
4. Press the
icon (B12) to confirm (or
(B10) to exit
without making the modification). The lights/icons go off.
The energy saving setting is now programmed.
13.2 Selecting the quantity of coffee in the cup
The appliance is set by default to automatically make the following quantities of coffee:
coffee requested
Please note:
• When in energy saving mode, a few seconds may elapse
before the first coffee is delivered as the appliance must
heat up again.
icon
quantity delivered
1 short coffee
(≃40ml)
1 long coffee
(≃120ml)
2 short coffees
(≃40ml) x2
2 long coffees
(≃120ml) x2
To change the quantity of coffee the appliance delivers automatically into the cup, proceed as described below:
- press and hold the icon
(B2) or
icon (B11) (depending on the quantity you want to modify) until the icon
flashes and all the alarm lights flash 4 times. When the
appliance starts delivering coffee, release the icon;
- when the coffee in the cup reaches the required level, press
the same icon again to memorise the new amount.
When the icon is pressed again, the new quantities have been
memorised.
12. DEFAULT VALUES (RESET)
This function resets all settings (temperature, auto-off, water hardness, energy saving and all quantity settings are reset to the default
values).
1. With the appliance off (standby), but the main switch
(A15) pressed (fig. 4).
11
Please note!
Programming the one coffee quantity also programmes the
quantity of coffee in the corresponding two cups.
coffee requested
13.3 Adjusting the coffee mill
2 short coffees
icon
1 short coffee
1 long coffee
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (A21 - fig. 8).
2 long coffees
5. Preparation begins and the light corresponding to the selected icon lights steady on the touch screen (B).
Once the coffee has been made, the appliance is ready to make
the next drink.
Please note!
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
If the coffee is delivered too slowly or
not at all, turn one click clockwise towards “7”.
For fuller bodied creamier coffee, turn
one click anticlockwise towards “1” (do
not turn more than one click at a time
otherwise the coffee could be delivered a drop at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
•
•
Please note:
While the machine is making coffee, delivery can be interrupted at any moment by pressing any button.
At the end of delivery, to increase the quantity of coffee
in the cup, just press one of the coffee icons (within 3
seconds).
Once the coffee has been made, the appliance is ready to make
the next drink.
Important!
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in the “23. Troubleshooting” section.
• Lights may be displayed on the touch screen during use.
Their meaning is given in the section “22. Explanation of
the lights”.
• For hotter coffee, see the section “13.4 Tips for a hotter
coffee”.
•
13.4 Tips for a hotter coffee
For hotter coffee, you should:
• perform a rinse cycle before delivering the coffee by pressing the
icon (B10).
• Warm the cups with hot water (using the hot water
function).
• Increase the coffee temperature as described in section “9.
Setting temperature” section.
13.6 Making coffee using pre-ground coffee
Important!
Never place coffee beans in the pre-ground coffee funnel
(A4) as this could damage the appliance.
• Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
• Never use more than 1 level measure (C2) or it could dirty the inside
of the coffee machine or block the
funnel.
•
13.5 Making coffee using coffee beans
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1.
2.
3.
Fill the container with coffee beans (A3- fig. 9).
Place under the coffee spouts:
- 1 cup, if you want to make 1 coffee (fig. 10);
- 2 cups, if you want 2 coffees (fig. 11).
Lower the spouts (A9) as near as possible to the cup. This
makes a creamier coffee (fig. 12).
4. Press the icon corresponding to the required coffee:
Please note!
When you use pre-ground coffee, you can only make one cup of
coffee at a time.
1. Make sure the appliance is on.
2. Turn the dial
(B9) anticlockwise to the position
.
12
13.11Customising the “LONG coffee” quantity
3. Open the pre-ground coffee funnel lid (A2).
4. Make sure the funnel (A4) is not blocked, then add one
level measure of pre-ground coffee (fig. 13).
5. Place a cup under the coffee spouts (A9 - fig. 10).
6. Press the 1 cup coffee icon
(B2).
7. Preparation begins.
The appliance is set by default to automatically deliver about
180ml of LONG coffee. To modify these settings, proceed as
follows:
1. Place a sufficiently large cup or glass under the coffee
spouts (A9).
2. Press and hold the icon
(B13) until the icon flashes
and all the alarm lights flash 4 times.
3. Release the icon
. The appliance starts delivering
coffee.
4. As soon as the coffee in the cup reaches the required level,
press the icon again
.
The quantity of coffee in the cup has now been programmed.
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the first coffee is delivered.
13.7 Making DOPPIO+ coffee using coffee beans
Prepare the appliance following the instructions in the section
“13.5 Making coffee using coffee beans”, then press the icon
(B15).
14. MAKING CAPPUCCINO
13.8 Customising the DOPPIO+ coffee quantity
Danger of burns!
During preparation steam is given off. Take care to avoid scalds.
The appliance is set by default to deliver about 120 ml of DOPPIO+ coffee. To modify these settings, proceed as follows:
1. Place a sufficiently large cup or glass under the coffee
spouts (A9).
2. Press and hold the
icon (B15) until the icon flashes
and all the alarm lights flash 4 times(fig. 14).
3. Release the
icon. The appliance starts delivering
coffee.
4. As soon as the coffee in the cup reaches the required level,
press the icon again
.
The quantity of coffee in the cup has now been programmed.
1. When preparing cappuccino, make the coffee in a large
cup.
2. Fill a container (preferably one with a handle to avoid
scalding) with about 100 grams of milk for each cappuccino. In choosing the size of the container, bear in mind that
the milk doubles or triples in volume.
Please note!
You can programme a minimum quantity of about 80ml.
You can programme a maximum quantity of about 160ml.
3.
13.9 Making LONG coffee using coffee beans
Prepare the appliance following the instructions in the section
“13.5Making coffee using coffee beans”, then press the icon
(B13).
4.
13.10Making LONG coffee using pre-ground coffee
6.
5.
1. Follow the instructions in points 1, 2, 3 and 4 of the section
“13.6Making coffee using pre-ground coffee”, then press
the icon
(B13).
2. The appliance starts delivering coffee. Halfway through
preparation, the light
(B6) comes on and the light
(B4) and icon
flash.
3. Place the pre-ground coffee in the funnel (A4).
4. Press the icon
. Preparation resumes.
7.
8.
9.
Please note :
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C). To avoid milk
with poor froth or large bubbles, always clean the cappuccino maker as described in the section “14.1Cleaning the
cappuccino maker after use”.
The cappuccino maker (A7) can be turned slightly outwards to allow containers of any size to be used.
Immerse the cappuccino maker in the milk container.
Never immerse the black ring.
Press the icon
(B12). The light (B3) flashes to indicate the appliance is heating up.
When the appliance is at temperature, the light goes off
and the icon
flashes.
Turn the hot water/steam dial
(B1) to the I position.
For a creamier froth, rotate the container with slow movements in an upward direction. (You should not discharge
steam for more than 3 minutes at a time).
When you have obtained the required froth, stop steam
delivery by turning the dial to the “O” position. The icon
flashes.
Press the icon to exit the steam function
.
Danger of burns!
Interrupt steam delivery before removing the container with the
frothed milk to avoid burns caused by splashes of boiling milk.
13
10. Add the milk froth to the coffee prepared previously. The
cappuccino is ready. Sweeten to taste and, if desired, sprinkle the froth with a little cocoa powder.
-
-
-
-
-
coffee spouts (A9),
cappuccino maker (A8),
the hot water/steam connection nozzle (A9),
pre-ground coffee funnel (A2),
the infuser (A17), accessible after opening the service door
(A16),
- control panel (B).
Please note!
If “Energy saving” is active, you may have to wait a few seconds
before steam is delivered.
14.1 Cleaning the cappuccino maker after use.
•
•
Clean the cappuccino maker (A7) each time you use it to avoid
the build-up of milk residues or blockages.
Danger of burns!
When cleaning the cappuccino maker, a little hot water is delivered. Avoid contact with splashes of water.
1. Deliver a little water by turning the hot water/steam dial
(B1) to the I position. Then stop delivery by turning
the dial back to the 0 position.
2. Wait a few minutes for the cappuccino maker to cool down.
Turn the cappuccino maker downwards to remove it (fig.
15).
3. Remove the nozzle downwards (A8 - fig. 16).
4. Make sure the two holes shown by the arrow in fig. 17 are
not blocked. If necessary, clean with a pin.
5. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, pushing it upwards and turning it until it is
attached.
•
Important!
None of the components can be washed in a dishwasher.
Do not use solvents, abrasive detergents or alcohol to clean
the coffee machine. With De’Longhi superautomatic coffee
machines, you need not use chemical products to clean the
machine.
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
16.2 Cleaning the machine’s internal circuit
If the appliance is not used for more than 3-4 days, before using
it again, we strongly recommend switching the appliance on
and performing:
• 2 or 3 rinse cycles by pressing the
icon (B10).
• hot water by turning the hot water/steam dial (B1) to the I
position.
Please note:
After cleaning, it is normal for the grounds container (A14) to
contain water.
15. DELIVERING HOT WATER
16.3 Cleaning the coffee grounds container
Important! Danger of burns.
Never leave the machine unattended while delivering hot water.
The hot water spout becomes hot while water is being delivered
and must be handled by the handle only.
1. Place a container under the cappuccino maker (A7) (as
close as possible to avoid splashes).
2. Turn the hot water/steam dial
(B1) to the I position.
4. To stop hot water delivery manually, turn the hot water/
steam dial
to the 0 position.
When the light flashes on the display (B4), the grounds container (A14) must be emptied and cleaned. The appliance cannot be used to make coffee until you have cleaned the grounds
container (A14). Even if not full, the empty grounds container
message is displayed 72 hours after the first coffee has been prepared. For the 72 hours to be calculated correctly, the machine
must never be turned off with the main switch.
To clean (with the machine on):
• Remove the drip tray (A13 - fig. 18), empty and clean.
• Empty the grounds container (A14) and clean thoroughly
to remove all residues left on the bottom. This can be done
using the spatula on the brush (C2) provided.
• Check the condensate tray (A10) and empty if necessary
(fig. 19).
Please note!
If “Energy Saving” is active, you may have to wait a few seconds
before hot water and steam are delivered.
16. CLEANING
16.1 Cleaning the machine
Important!
When removing the drip tray,the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coffees, the grounds container may fill
up more than expected and clog the machine.
The following parts of the machine must be cleaned regularly:
- the appliance’s internal circuit;
- coffee grounds container (A14),
- clean the drip tray (A13) and condensate tray (A10)
regularly;
- water tank (A18),
14
16.4 Cleaning the drip tray and condensate tray
16.9 Cleaning the infuser
The infuser (A17) must be cleaned at least once a month.
Important!
The drip tray (A13) is fitted with a level indicator (red) (A12)
showing the level of water it contains (fig. 20). Before the indicator protrudes from the cup tray, the drip tray must be emptied
and cleaned otherwise the water may overflow the edge and
damage the appliance, the surface it rests on or the surrounding
area.
To remove the drip tray:
1. Remove the drip tray and the grounds container (A14) (fig.
18).
2. Empty the drip tray and grounds containe and wash them.
3. Check the condensate tray (A10) and empty if necessary.
4. Replace the drip tray and grounds container.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see “7. Turning off”).
2. Open the infuser door (A16 - fig. 23) on the right side of the
appliance.
3. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (fig. 24).
4. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
5. Use the brush (C5) to remove any coffee residues left in the
infuser housing, visible through the infuser door.
6. After cleaning, replace the infuser by sliding it onto the
internal support (fig. 25), then push the PUSH symbol fully
in until it clicks into place.
16.5 Cleaning the inside of the coffee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned off
(see “Turning off”) and unplugged from the mains power supply. Never immerse the coffee machine in water.
1. Check regularly (about once a week) that the inside of the
appliance (accessible after removing the drip tray (A13))
is not dirty. If necessary, remove coffee deposits with the
brush (C5) supplied and a sponge.
2. Remove the residues with a vacuum cleaner (fig. 21).
Please note:
If the infuser is difficult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in fig. 26.
7. Once inserted, make sure the two coloured buttons have
snapped out (fig. 27).
8. Close the infuser door.
16.6 Cleaning the water tank
1. Clean the water tank (A18) regularly (about once a month
and whenever you replace the water softener filter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid.
2. Remove the filter (if present) and rinse with running water.
3. Replace the filter (if provided), fill the tank with fresh
water and replace the tank.
4. (Models with water softener filter only) Deliver about
100ml of hot water to reactivate the filter.
17. DESCALING
Descale the appliance when the
control panel (B9).
•
•
16.7 Cleaning the coffee spouts
1. Clean the coffee spouts (A9) regularly with a sponge or
cloth (fig. 22).
2. Check the holes in the coffee spout are not blocked. If necessary, remove coffee deposits with a toothpick (fig. 22).
16.8 Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel (A4) is not blocked. If necessary, remove coffee
deposits with the brush (C5) supplied.
15
light (B7) flashes on the
Important!
Before use, read the instructions and the labelling on the
descaler pack.
You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer’s guarantee.
1. Press the
button (A5- fig. 7) to turn the appliance off
(stand-by).
2. Empty the drip tray (A13) and grounds container (A14) and
put both back in the machine.
3. Press and hold the
icon (B11) until the
(B7),
(B12) and
(B10) lights come on.
4. Empty the water tank (A18) completely and remove the
water softener filter (C5), if present.
5. Pour the descaler (C3) into the tank up to level A (corresponding to a 100 ml pack) marked on the back of the tank,
then add water (1 litre) up to level B (fig. 28) and put the
water tank back in the appliance.
6. Place a container with a minimum capacity of 1.4 litres
under the cappuccino maker (A7) and coffee spout (A9)
(fig. 29).
Please note
If the descaling cycle is not completed correctly (e.g. lack of
electricity) we recommend repeating the cycle.
• After descaling, it is normal for the grounds container
(A14) to contain water.
•
Important! Danger of burns
Hot water containing acid flows from the cappuccino maker and
coffee spout. Take care to avoid contact with splashes of this
solution.
7. Press the icon
to confirm that you have added the
solution.
8. The icon
flashes to indicate the hot water/steam
dial
(B1) must be turned to the I position.
9. When the dial is turned to the I position, the descaler programme begins and the descaler solution is delivered from
the cappuccino maker and coffee spout. A series of rinses
and pauses is performed automatically to remove scale
deposits from inside the machine.
After about 25 minutes, descaling stops and the icon
flashes on the display panel. Turn the hot water/steam dial
to the 0 position: the light (B5) flashes.
10. The appliance is now ready for rinsing through with clean
water. Extract the water tank, empty, rinse under running
water, fill with fresh water up to the MAX level and put
back in the appliance: the
icon flashes.
11. Empty the container used to collect the descaler solution
and replace it empty under the cappuccino maker and coffee spout (fig. 29).
12. Turn the hot water/steam dial
to the I position to
begin rinsing. Hot water is delivered first from the cappuccino maker, to continue and end with the coffee spout.
13. When the water tank is completely empty, the icon
on the control panel flashes. Turn the hot water/steam dial
to the 0 position. The light flashes.
14. Remove the water tank, replace the water softener filter
(if previously removed), fill the tank up to the MAX level
with cold water and insert in the appliance. The
icon
flashes.
15. Empty the container used to collect the rinsing water and
replace it empty under the cappuccino maker.
16. Turn the hot water/steam dial
to the I position. The
appliance resumes rinsing from the cappuccino maker
only.
18. SETTING WATER HARDNESS
The light (B7) comes on after a period of time established
according to water hardness.
The machine is set by default for a hardness value of 4. The machine can also be programmed according to the hardness of the
mains water in the various regions so that the machine needs to
be descaled less often.
18.1 Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
soft water
slightly
hard water
hard water
very hard
water
18.2 Setting water hardness
1. With the appliance off (standby), but the main switch
pressed (A15 - fig. 4).
2. Press the
icon (B14) until the icon lights up, together with the lights indicating the current setting.
3. Press the icon
(B13) to select the hardness identified
with the indicator paper.
4. Press the icon
(B12) to confirm (or
(B10) to exit
without making the modification).
The machine is now reprogrammed with the new water hardness setting.
17. When the water tank is completely empty, the
icon and
light flash on the touch screen. Turn the hot
water/steam dial to the 0 position.
18. Top up the water tank with fresh water to the MAX level
and put back in the machine.
Descaling is complete.
16
19. WATER SOFTENER FILTER (*CERTAIN MODELS
ONLY)
1. Extract the tank (A18) and exhausted filter (C4);
2. Take the new filter out of its packet and proceed as illustrated in points 2 to 10 in the previous section.
The new filter is now active and you can use the coffee machine.
Certain models are fitted with a water softener filter. If this is not
the case with your model, you are recommended to purchase
one from De’Longhi Customer Services.
To use the filter correctly, follow the instructions below.
20. TECHNICAL DATA
Voltage
220-240 V~ 50/60 Hz max. 10 A
Power 1450 W
Pressure
1,5 MPa (15 bar)
Water tank capacity
1,4 L
Size LxDxH
195x480x340 mm
Cable length
1100 mm
Weight
9,1 Kg
Beans container capacity: 200 g
19.1 Installing the filter
1. Remove the filter (C4) from the packaging.
2. Turn the date indicator disk (see fig. 30) until the next two
months of use are displayed.
Please note:
The filter lasts about two months if the appliance is used normally. If the coffee machine is left unused with the filter installed, it will last a maximum of three weeks.
3. To activate the filter, run tap water through the hole in the
filter as shown in the figure until water comes out of the
openings at the side for more than a minute (fig. 31).
4. Extract the tank (A18) from the appliance and fill with
water.
5. Insert the filter in the water tank and immerse it completely for about ten seconds, sloping it and pressing it lightly
to enable the air bubbles to escape (fig. 31).
6. Insert the filter in the filter housing (fig. 32) and press as
far as it will go.
7. Close the tank with the lid (fig. 33), then replace the tank
in the machine.
32
This product complies with European regulation no.
1935/2004 on materials and articles intended to come
into contact with food.
21. DISPOSING OF THE APPLIANCE
The appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.
33
8. Position a container under the hot water spout (A7) (min.
capacity: 500 ml).
9. Deliver hot water by turning the hot water/steam dial
(B1) to the I position.
10. Deliver at least 500 ml of hot water, then turn the hot
water/steam dial
to the O position.
The filter is now active and you can use the coffee machine.
19.2 Replacing the filter
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter:
17
22. EXPLANATION OF LIGHTS
LIGHTS DISPLAYED
POSSIBLE CAUSE
REMEDY
Insufficient water in the tank (A18).
Fill the tank (A18) with water and/or insert it
correctly, pushing it as far as it will go until it
clicks into place.
The grounds container (A14) is full.
Empty the grounds container and drip tray
(A13), clean and replace (fig. 18). Important:
when removing the drip tray, the grounds container must be emptied, even if it contains few
grounds. If this is not done, when you make the
next coffees, the grounds container may fill up
more than expected and clog the machine.
FLASHING
FLASHING
After cleaning, the grounds container has not Remove the drip tray (A13) and insert the
been replaced.
grounds container.
ON
The coffee beans have run out.
Fill the beans container (fig. 9).
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a brush as
described in the section “16.8 Cleaning the
pre-ground coffee funnel”.
ON + FLASHING
The "pre-ground coffee" function has been se- Place pre-ground coffee in the funnel or deselected without placing any pre-ground coffee lect the "pre-ground" function (fig. 13).
in the funnel.
FLASHING + ON
The machine must be descaled.
The descaling procedure described in the “17.
Descaling" section needs to be performed as
soon as possible.
FLASHING
FLASH. + ON + FLASH.
The grinding is too fine and the coffee is delive- Repeat coffee delivery and turn the grinding
red too slowly or not at all.
adjustment dial (fig. 8) one click clockwise towards "7" while the coffee mill is in operation.
If after making at least 2 coffees delivery is
still too slow, repeat the correction procedure,
turning the Grinding adjustment dial another
click until delivery is correct (see the section
“16.8 Adjusting the coffee mill"). If the problem persists, make sure the water tank is fully
inserted, turn the hot water/steam dial to the I
position and deliver a little water until the flow
is regular.
If the water softener filter (C3) is present, an Deliver a little water by turning the steam dial
air bubble may have been released inside the to the Iposition until the flow is normal.
circuit, obstructing delivery.
18
Too much coffee has been used.
Select a milder taste by turning the
dial
or reduce the quantity of pre-ground coffee.
The water circuit is empty
Turn the hot water/steam dial (B1) to the I position until delivery stops, then bring it back
to the 0 position. If the alarm occurs while hot
water or steam is being delivered, turn the dial
to the O position, then resume delivery. If the
problem persists, make sure the water tank is
fully inserted.
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly,
as described in the section “16. Cleaning". If
the message is still displayed after cleaning,
contact a service centre.
FLASH. + FLASH.
FLASH. + FLASH.
FLASHING
ON
The infuser has not been replaced after clea- Insert the infuser as described in the section
ning (A17).
"16.9 Cleaning the infuser".
FLASHING
The infuser door (A16) is open.
Close the door.
ON + ON
Indicates the hot water/steam dial must be The dial (B1) must be turned.
turned (B1).
FLASHING
19
23. TROUBLESHOOTING
Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services.
Problem
POSSIBLE CAUSE
REMEDY
The coffee is not hot.
The cups were not preheated.
Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The infuser (A17) has cooled down be- Before making the coffee, heat the infuser by
cause 2/3 minutes have elapsed since rinsing using the rinse function (section “13.4
Tips for a hotter coffee”).
the last coffee was made.
A low coffee temperature is set.
The coffee is weak or not creamy The coffee is ground too coarsely.
enough.
The coffee is unsuitable.
Set a higher coffee temperature in the menu
(section “9. Setting the temperature").
Turn the grinding adjustment dial one click anticlockwise towards "1" while the coffee mill
is in operation (fig. 8). Continue one click at
a time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see section “13.3 Adjusting the coffee mill").
Use pre-ground coffee for espresso machines.
The coffee is delivered too slowly or a The coffee is ground too finely.
drop at a time.
Turn the grinding adjustment dial one click
clockwise towards "7" while the coffee mill is
in operation (fig. 8). Continue one click at a
time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see section “13.3 Adjusting the coffee mill").
Coffee does not come out of one or The spouts are blocked.
both of the spouts.
Clean the spouts with a toothpick (fig. 22).
The milk is not frothed
Cappuccino maker dirty.
Clean the cappuccino maker as described in
the section "14.1 Cleaning the cappuccino
maker after use".
Steam delivery stops
A safety device stops steam delivery Wait, and then enable the steam function
again.
after 3 minutes.
The appliance does not come on
The plug on the cord (A22) is not plug- Plug into the mains socket.
ged in.
The main switch (A15) is not turned on. Press the main switch (fig. 4).
The infuser cannot be extracted
The appliance has not been turned off Turn the appliance off by pressing the button
(section “7. Turning off").
correctly
The frothed milk has large bubbles
The milk is not cold enough or is not You should ideally use skimmed or semi-skimmed milk at refrigerator temperature (about
semi-skimmed.
5°C). If the result is not as you wished, try
changing brand of milk.
The milk is not frothed
Cappuccino maker dirty.
Steam delivery stops
A safety device stops steam delivery Wait, and then enable the steam function
again.
after 3 minutes.
20
Clean as described in the section "14.1 Cleaning the cappuccino maker after use".
24. ELECTRICAL CONNECTION (UK ONLY)
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might find it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
GREEN AND YELLOW EARTH
BLUE NEUTRAL
BROWNLIVE
13 amp Fuse
Blue to
neutral
Brown to live
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should
only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
21
Download PDF