MW402 Integrated Dishwasher
Manual for Installation, Use and Maintenance
1
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
Important
• Read the instructions prior to installation and use of the appliance.
• Do not lean or climb on the open dishwasher door, to prevent
damage.
• Close the dishwasher door after use, to prevent accidents.
• Use only detergents, salt and rinse aid specifically designed for
dishwashers.
• Do not put solvents in the dishwasher detergent compartment, to
prevent risk of explosion.
• Only put dishwasher safe items into the dishwasher. If in doubt,
check with the manufacturer of the items.
• Take care when loading the dishwasher to observe the
recommendations for best loading practice, and also to ensure that
sharp objects such as knives are placed blade down, to prevent
accidents.
• Do not open the dishwasher door when a programme is running.
If it is necessary to do so, then open it only slightly to allow the
dishwasher to pause the programme and prevent any water spilling
out. Remember that the water in the dishwasher can be very hot
when the programme is running.
• When the dishwasher is not in use, we recommend that you turn off
the water supply at the supply tap and disconnect the mains supply.
• If you are leaving the dishwasher for an extended period you should
leave the door slightly open to prevent the formation of unpleasant
smells.
•The plastic housing on the water inlet pipe contains an electrically
operated valve. The wires that connect to this valve are inside the
inlet hose. Do not cut through the inlet hose, and do not put the
plastic housing in water.
2
•Children could get locked inside the appliance. Therefore when
disposing of an old appliance, cut off the plug and set aside, and
damage the door lock so that the door can no longer be closed.
•This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not
be made by children without supervision.
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note
that CDA reserve the right to invalidate the guarantee supplied with
this product following incorrect installation or misuse of the appliance.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
3
Appliance information
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
EU Declarations of Conformity
This product meets the requirements of all applicable EU directives
with the corresponding harmonised standards, which provide for CE
marking.
Availability of this manual in an alternative format:
A soft copy of this manual is available for download from www.cda.eu.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must be taken to a special
local authority waste collection centre or to a dealer providing
appliance recycling services.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health. It also
enables the constituent materials to be recovered, saving both energy
and resources. As a reminder of the need to dispose of household
appliances separately, the product is marked with a crossed-out
wheeled dustbin.
4
Recommendations
•To reduce energy and water consumption, remove all dirt residues
from the dishes prior to loading the dishwasher.
• Only run the dishwasher when fully loaded.
•Place hollow items (bowls, glasses and pans) face down in the
basket.
•Do not put dishes or cutlery with tobacco ash, wax, lubricating
grease or paint residues in the dishwasher.
Before First Use
•Set the water softener level as required for the water hardness in
the area.
•Add 1kg of salt into the salt compartment and then fill with water to
the top of the salt compartment.
•Remove all the packaging materials from the interior of the
dishwasher.
• Fill the rinse aid compartment.
• Run a hot programme without any dishes in the dishwasher.
5
Control Panel
P1
65°C intensive
P1
65°C express
P2
50°C eco
P3
P2
P3
salt
P4
rinse aid
prewash
programme
end
MW402
salt
P4
rinse aid
programme
end
Fig. 1
“Power” button (1)
To switch the dishwasher on or off, press the “Power” button (1). When
you switch on the dishwasher, the “End of Programme” light will
illuminate, and two dashes will appear on the display.
“Programme Selection” button (2)
To select a programme, press the “Programme Selection” button (3).
The dishwasher will store in its memory the last programme used.
“Programme Indicator” lights (3)
These lights will illuminate to confirm which programme has been
selected. If there is a fault on the dishwasher, the fault code will show
on these lights.
“Salt” and “Rinse Aid” warning lights and “End of Programme”
light (4)
When either the dishwasher salt or rinse aid begins to run out, a
warning light will illuminate to advise that it needs refilling.
When the programme is complete, the dishwasher will emit five beeps
and the “End of Programme” light will illuminate.
6
Starting a programme
•Press the “Power” button (the “End of Programme” light will be
switched on).
•Press the “Programme Selection” button until the required
programme is shown on the indicator lights.
•Once a programme is selected, the “End of Programme” light will
switch off.
•When you close the dishwasher door, the programme will start
automatically.
Please note: The dishwasher stores the most recently used
programme in its memory. To change the programme, simply
press the “Programme Selection” button.
At the end of a programme
If possible, do not open the dishwasher door once the programme
has started.
At the end of a programme, the dishwasher will beep five times, and
the “End of Programme” indicator light will switch on.
Changing a programme
It is possible to change the programme, if necessary, once the
programme has started.
• First open the door slightly to reduce the risk of water spillage.
•Press the “Programme Selection” button until the required
programme is shown on the display.
•Close the door. The dishwasher will begin the new programme
from the point at which the old programme stopped.
7
Cancelling a programme
It is possible to cancel a programme once is has started.
• First open the door slightly to reduce the risk of water spillage.
•Press and hold in the “Programme Selection” button until the “End
of Programme” indicator flashes.
•Close the door. The dishwasher will run a drain cycle which will take
approximately 30 seconds. Once this is complete, the dishwasher
will beep five times and the “End of Programme” light will switch on.
Switching the dishwasher off
•Once the dishwasher beeps five times and the “End of Programme”
light switches on, the dishwasher can be switched off by pressing
the “Power” button.
•Turn off the water tap and remove the plug from the power socket.
Please note: The dishwasher will automatically continue on the
programme it has started if the door is opened or in the event of a
power cut.
8
Detergent
To fill the detergent compartment
•Push the latch to open the
compartment.
• Add the required amount of
Fig. 2
detergent. The main detergent
compartment “b” (Fig. 2) has lines to allow for specific amounts of
detergent. These are marked at either 15cm3 or 25cm3, to be used
depending on how dirty the dishes are.
If your dishes are in need of an intensive wash, then add 5cm3 of
detergent into the prewash section of the compartment “a” (Fig. 2).
• Close the detergent compartment lid until the latch locks.
Please note: You should only use detergents designed specifically
for use in dishwashers.
If using dishwasher tablets, always use the detergent compartment,
do not put them in the main body of the dishwasher or in the cutlery
basket. The solubility of dishwasher tablets can vary depending on
the temperature and duration of the programme. As a result, it is
recommended that powder detergents should be used in the shorter
programmes to allow better performance.
The use of separate detergent, rinse aid and dishwasher salt is
recommended rather than combination tablets as separates achieve
better wash performance.
9
If you do use combination detergents, add salt and rinse aid to the
dishwasher and then adjust the water hardness setting and rinse aid
setting to the minimum. When you then use separate detergents
again, you should fill the salt and rinse aid compartments, adjust the
water hardness setting to the maximum and run an empty wash, then
adjust the water hardness setting and the rinse aid setting to the
appropriate level.
Salt
Detergent
To fill the detergent compartment
To ensure the best efficiency, the dishwasher needs soft water. Hard
water means that lime residues remain on the dishes and the interior
of the dishwasher, affecting performance. The softener system is
If your dishes are in need of an intensive wash, then add 5 cm3 of
detergent
into the prewash
section of the
compartment
“a” (figure
2).
designed
to remove
the
ions that
make
the water hard and provide
3. Then close the detergent compartment lid until the latch locks.
the best quality wash performance. This is achieved by using
fig 1
Detergent
Please note: You should only use detergents designed specifically for
dishwasher
salt.
in dishwashers.
To use
fill the
detergent compartment
1. Push the latch as shown in figure 1.
2. Add the required amount of detergent. The main detergent
compartment “b” (figure 2) has lines to allow for specific amounts of
detergent. These are marked at either 15 cm3 or 25 cm3, to be
used depending on how dirty the dishes are.
1. Push the latch as shown in figure 1.
using
dishwasher
tablets, always
use the detergent
2. IfAdd
the
required amount
of detergent.
The maincompartment,
detergent do not put
them
in the main
body
of the
in thefor
cutlery
basket.
The solubility
compartment
“b”
(figure
2)dishwasher
has lines toorallow
specific
amounts
of
of
dishwasherThese
tablets
vary depending
on cm
the3temperature
and
detergent.
arecan
marked
at either 15
or 25 cm3, to
beduration of
the programme. As a result, it is recommended that powder detergents should
used depending on how dirty the dishes are.
To add dishwasher salt
be used
the shorter programmes
to allow dishwasher
better performance.
•inRemove
the lower
If your dishes are in need of an intensive wash, then add 5 cm3 of
detergent
into
the
prewash
section
of
the
compartment
“a” (figure
basket
and
thendetergent,
unscrew
salt 2).salt
CDA recommends
the use
of separate
rinse aidthe
and dishwasher
3. rather
Then than
closecombination
the detergent
compartment
lid
until
the
latch
locks.
tablets as separates achieve better wash performance.
compartment cap (Fig. 3).
Please
You
should only
use detergents
designed
for
If younote:
do use
combination
detergents,
add salt and
rinse aidspecifically
to the dishwasher
•
Fill
the
compartment
with
dishwasher
then
adjust
the water
hardness setting and rinse
aid setting
to the
useand
in dishwashers.
minimum. When you then use separate detergents again, you should fill the
salt and rinse
aid (do
compartments,
adjusttable
the watersalt)
hardness
setting to the
salt
not use
carefully,
maximum
and run
an empty
wash,
adjust the water
hardness do
setting
and
If using
dishwasher
tablets,
always
usethen
the detergent
compartment,
not put
the
rinse
aid
setting
to
the
appropriate
level.
them in the main
body of the dishwasher
or in
thespillage
cutlery basket.(Fig.
The solubility
to
reduce
the
risk
of
4).
of dishwasher tablets can vary depending on the temperature and duration of
theSalt
programme. As a result, it is recommended that powder detergents should
Before first use, you should fill the salt
be used in the shorter programmes to allow better performance.
To ensure the best efficiency, the dishwasher needs soft water. Hard water
means that
lime residues remain onwith
the dishes
and of
the interior
of the
compartment
1kg
dishwasher
dishwasher,
affecting
performance.
softenerrinse
system
designed
to salt
CDA
recommends
the use
of separateThe
detergent,
aid is
and
dishwasher
remove
ions that
make
theaswater
hardup
to
provide
the
best
wash
rather
thanthe
combination
tablets
separates
achieve
better
washquality
performance.
salt
and
then
top
the
compartment
performance. This is achieved by using dishwasher salt.
water
(up to
theandbrim
the
If you do usewith
combination
detergents,
add salt
rinse aidof
to the
dishwasher
To add dishwasher salt, follow the steps below:
and then adjust the water hardness setting and rinse aid setting to the
1. Remove
theyou
lower
dishwasher
basket
and4).
thenagain,
unscrew
salt fill the
compartment)
(Fig.
minimum.
When
then
use separate
detergents
youthe
should
cap, as shownadjust
in figure
salt andcompartment
rinse aid compartments,
the 1.water hardness setting to the
2. Fill the
dishwasher
saltthe
(dowater
not use
table salt),
carefully
maximum
andcompartment
run an emptywith
wash,
then adjust
hardness
setting
and
to prevent
unnecessary
spillage (figure
the rinse
aid setting
to the appropriate
level.3). Before first use, you should
fill the compartment with 2kg of dishwasher salt and then fill up the salt
10compartment with water (up to the brim of the compartment) as shown
in figure 3.
Replace
the cap
and thethe
lower
basket. needs soft water. Hard water
To 3.
ensure
the best
efficiency,
dishwasher
Salt
means that lime residues remain on the dishes and the interior of the
fig 2
fig
1 3
Fig.
fig 2
SALT
fig
3
Fig.
4
• Replace the cap and the lower basket.
When the salt warning light on the control panel illuminates, you
should refill the salt compartment with salt only – do not add water to
the salt compartment after the first use.
Important:
You should run a prewash programme immediately after adding
dishwasher salt, to prevent any damage to the dishwasher system.
Softener Adjustment
The efficiency of your dishwasher depends on the softness of the
tap water. To ensure best efficiency, the dishwasher is equipped with
a system that reduces the hardness in the mains water supply. The
efficiency will increase when the system is correctly set. To find out
the water hardness level of your water supply you can use the test
strip supplied, or alternatively contact your local water board.
Fig. 5
• Open the testing strip (Fig. 5).
• Run water through the tap for one minute.
• Hold the testing strip in water for one second.
• Remove from the water and shake the test strip to remove excess
water.
11
• Wait for one minute.
• Check the number of marks on the strip to see the level of water
hardness.
If the hardness of the water you use is above 63dE, or if you are
using well water, you are recommended to contact your local water
board to confirm the water hardness level and to use filter and water
refinement devices.
Please note: The water hardness is preset to level “3”.
To change the hardness setting
• Press and hold down the “Programme Selection” button.
• Press the “Power” button to switch on the dishwasher.
• Keep the “Programme Selection” button pressed until all
“Programme Indicator” lights and the “End of Programme” indicator
light flash.
• To adjust the level, press the “Programme Selection” button until the
required level is shown on the display: The “Programme” lights will
illuminate as in the table below.
• To store the selected water hardness level, press the “Power”
button.
12
Water hardness level
British hardness dE
Indicator lights illuminated
1
0-6
P1
2
7-14
P2
3
15-21
P3
4
22-28
P4
5
29-39
P1 and P4
6
40-63
P2 and P4
Aid
se Aid
Rinse Aid
se rinse
aid compartment
he
aidAid
compartment
Rinse
een
rinse
aidrinse
compartment
by turning
andaid
removing
the the
cap cap
as as
the
rinse
aidaid
compartment
by
turning
and
removing
To
fill the
rinse
compartment
To
fill the
compartment
figure
4.
wn in figure 4.
1. Open the rinse
aidpen
compartment
by turning
removing the cap as
• O
the rinse
aidandcompartment
by
6).
•
Fill5 (where
the
aid
until
ates
compartment
is full).
asthe
shown
figure
afull).
indicates
thecompartment
compartment is empty,
and
indicates
theincompartment
isrinse
“b”
indicates
the
compartment
is
full).
the
rinse
aid
indicator
goes
dark
the
the markers
on the
up with
the the
lacecap,
the ensuring
cap, ensuring
the markers
on cap
the line
cap line
up with
3. Replace
thescrewing
cap,
ensuring
the
markers
on
the
cap
line
up
the
ment
priorprior
to
the
cap
back
in
place.
mpartment
to(Fig.
screwing
the
cap
back
in
place.
7, where “a” indicateswith
the
compartment prior to screwing the cap back in place.
compartment is empty, and “b”
Aid
Adjustment
se Aid
Adjustment
indicates the compartment is full).
Rinse Aid Adjustment
rinse
aid use
preset
to 4.toYou
can adjust
the level
of rinse
aid aid
el of rinse
aidisuse
is preset
4. You
can adjust
the level
of rinse
•aidReplace
cap,
The level of rinse
use is presetthe
to 4. You
can ensuring
adjust the levelthe
of rinse aid
ting as shown
in figure
6. 6.
adjusting
as shown
in figure
use by adjusting as markers
shown in figure
6. the cap line up with the
on
compartment prior to screwing the
rIfstains
on
theon
dishes
after
aafter
wash,
the level
should
be increased.
ns
form
on
the
dishes
after
a wash,
the
level
should
be
increased.
waterform
stains
form
the dishes
a wash,
the
level
should
be increased.
cap back in place.
nse rinse
aid compartment
the rinse
aid indicator
goesgoes
dark,
shown
in compartment
figure 4. untiluntil
the
aid
the rinse
aid indicator
dark,
turning and
removing
the cap
(Fig.
nhown
in
figure
5
(where
a
indicates
the
compartment
is
empty,
and
in
figure
5
(where
a
indicates
the
compartment
is
empty,
and
2. Fill the rinse aid compartment until the rinse aid indicator goes dark,
stains
can
becan
wiped
away
are on
left
on
the
after
a wash,
thethe
can be
wiped
away
are left
the
a wash,
Ifwhich
bluewhich
stains
which
be wiped
away
are
leftdishes
ondishes
theafter
dishes
after
athe
wash,
ould
be
decreased.
be
decreased.
level
should
be decreased.
figfig
46 4
Fig.
fig 4
Fig.
fig
figfig
5755
Rinse Aid Adjustment
note:
Rinse
aidlevel
ensures
better
quality
wash
results
and
The
of
rinse
aid
use
is and
preset
to
note:
aid
ensures
better
quality
wash
results
e:Please
RinseRinse
aid ensures
better
quality
wash
results
and
increased
drying
performance.
sed drying
performance.
drying
performance.
“3”. You can adjust the level of rinse
aid use by adjusting (Fig. 8). If water
refill
the aid
rinse
aid when
the rinse
aid indicator
light
sllAlways
refill
the
rinse
when
the rinse
aid indicator
light
on on
thethe
the rinse aidstains
when
the
rinse
aidthe
indicator
light
on the
form
on
dishes
after
a
wash,
control panel is illuminated.
Fig.
fig86
ol
is illuminated.
nelpanel
is illuminated.
figfig
6 6
the level should be increased. If blue
stains which can be wiped away are left on the dishes after a wash,
the level should be decreased.
Please note: Rinse aid ensures better quality wash results and
increased drying performance.
Always refill the rinse aid when the rinse aid indicator light on the
control panel is illuminated.
13
Dishwasher Baskets
To adjust the height of the upper
basket
• Open the basket retaining clips (Fig
9), turning them to the side.
Fig.9
• Remove the upper basket, and
relocate the alternate set of wheels
on the runner (Fig. 10), pushing the
basket back into place.
• Close the basket retaining clips.
Fig.10
The images below are provided as guidance as to best practice for
loading the dishwasher.
Lower Basket
Top Basket
Faulty loads
Fig. 11
14
Standard Loading and
Test Data
Capacity
•Upper and lower baskets: 12 place
settings.
•The upper basket should be adjusted
to high position.
•Cups should be placed onto the dish
rack pins.
Detergent / Rinse aid
•5 + 25cm3, in accordance with
EN50242-DIN 44990 IEC436
(international norms) / Rinse aid
dosage adjustment: 5.
Programme test
•Eco 50°C, in accordance with
EN50242 (international norms.).
Fig. 12
15
Programme
Listing
The values and
times provided in the
adjacent table have
been obtained under
laboratory conditions
according to relevant
standards. Actual
results obtained can
vary depending on
the conditions of the
dishwasher’s use and
environment. (mains
supply voltage, water
pressure, water
input temperature
and environmental
temperature).
Laboratory measured
value in accordance
with European
standard EN50242.
Reference
programme is ECO
50°.
16
Programme
name and
temperature
Intensive
65°
Express
65°
Eco
50°
Prewash
-
Level of soil
High
Medium
Medium
-
Detergent
required
A+B
A+B
A+B
-
Prewash
Prewash
Prewash
65° wash 65° wash 50° wash
Cold rinse Cold rinse Cold rinse
Hot rinse
Hot rinse Hot rinse
Dry
Dry
Programme
duration
(mins.)
Electricity
consumption
(kWh)
Water
consumption
(litres)
End
End
End
End
117
50
187
15
1.55
1.35
0.90
0.02
17.2
12.7
12.0
4.5
Care and Maintenance
Before beginning any care or
maintenance, you should always
disconnect the appliance from the
electricity supply, and also turn off the
water supply.
Door seals
Wipe the dishwasher door seals
regularly with a damp cloth to remove
any residues.
Filters
You should clean the filters at least once
a month.
•Remove the lower basket.
•Turn the micro-filter anticlockwise and
then lift it out (Fig. 13).
•Remove the coarse filter from the
micro-filter (Fig. 14).
•Remove the base filter from the
dishwasher compartment (Fig. 15).
You should clean and rinse the filters
thoroughly before replacing all the
sections in reverse order to that above.
The microfilter should lock into place
once it is secure (Fig. 16).
Fig. 13
Fig. 14
Fig. 15
Fig. 16
17
Please note: Never run a programme without the filters in place.
Incorrect fitting of the filters may reduce wash performance and
potentially damage your appliance.
Spray arms
You should clean the spray arms at least once a month.
•Remove the lower basket.
•Pull the lower spray arm upwards to remove it.
•To remove the upper spray arm, first remove the nut on the upper
spray arm by turning it.
You should clean and rinse the spray arms thoroughly before
replacing them. Ensure that the upper spray arm nut is securely
tightened when refitting the upper spray arm.
Dishwasher interior
To deal with an accumulation of dirt, oil or limescale in the dishwasher,
run an intensive programme with detergent when the dishwasher is
empty.
Alternatively, there are specialist dishwasher cleaners available that
can be used.
18
Failure Codes and Troubleshooting
The “Programme Indicators” also serve as a diagnostic display to help
in the event of a problem with the appliance.
Error Code
Intensive
Express
Eco
Prewash
Error description
Advice
Make sure the water inlet tap is fully
open.
Inadequate water
supply.
Close the water tap, separate the
water inlet hose from the tap and
clean the filter.
Restart your machine, contact
Customer Care if the error resumes.
Continual fill error.
Close the tap and contact Customer
Care.
Drain hose is blocked.
The waste water in
the machine cannot
be discharged.
The filters of your machine might be
blocked.
Restart the dishwasher and
cancel the programme. If the error
continues, contact Customer Care.
Heater error.
Contact Customer Care.
Alarm is active
against water
overflow.
Turn off the dishwasher and
disconnect the water supply.
Contact Customer Care.
Faulty electronic
card.
Contact Customer Care.
19
Failure Codes and Troubleshooting
Problem
Possible cause
Check the plug, fuse and circuit breakers of the
mains supply.
The programme will not start.
The water tap is turned off.
The dishwasher door is not fully closed.
The water inlet filter or the machine filters are
blocked.
Water remains inside the dishwasher at the end of a
programme.
The water drain hose is blocked or kinked.
The dishwasher stops in the middle of a programme.
Water inlet failure.
The filters are blocked.
Power failure.
Programme is on standby.
Poor loading of dishes hinders wash performance.
Insufficient detergent added.
Wash performance is of a low standard.
Inappropriate wash programme selected.
Spray arm is blocked.
Filters clogged or incorrectly fitted.
Water drain pump is blocked.
Insufficient detergent added.
Rinse aid setting is too low.
White stains on the dishes.
Insufficient dishwasher salt added.
Water softener setting is too low.
Salt compartment cap may not be completely closed.
The dishes are not completely dry at the end of a
programme.
A programme without a drying stage was selected.
Rinse aid setting is too low.
Dishes unloaded too soon (allow time for drying).
Different sets of cutlery should be kept separate.
There are rust stains on the dishes.
Too much salt (water softener setting is too high).
Salt compartment cap not completely closed.
Poor appliance earth (check mains electrical supply).
The door is not opening or closing properly.
20
Door tension not correctly adjusted for the decor
door.
Electrical Information
Warning! This appliance must be earthed.
The mains lead of this appliance has been fitted with a BS 1363A 13A
fused plug. To change a fuse in this type of plug, follow the steps
below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the
fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in
position.
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should
be cut off and disposed of safely to avoid the risk of electric shock.
A suitable alternative plug of at least 13A rating to BS 1363 should be
used.
21
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
•The wire which is coloured GREEN and YELLOW must be connected
to the terminal which is marked with letter (E) or by the Earth symbol
or coloured GREEN and YELLOW.
•The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter (N) or coloured BLACK or BLUE.
•The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter (L) or coloured RED or
BROWN.
If in doubt regarding the electrical connection of this appliance,
consult a qualified electrician. Do not shorten the supply cable, the
appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible
place.
If the power supply cord is damaged, it must replaced by a CDA
authorised agent.
22
Installation
•Do not install this appliance if it is
damaged in any way. Installing a
damaged appliance may invalidate
the warranty.
• The water supply tap should be
located in an adjacent cupboard
so that it can be accessed after
installation.
• Ensure the appliance is level by
adjusting the feet as necessary.
The dishwasher is equipped with an
adjustable rear foot that can be raised
or lowered by means of an adjustment
screw, located in the centre of the
kick plate.
• Only use the water inlet supplied with
the appliance.
• If the water pressure is above 10Bar, a
pressure relief valve should be used.
• After connecting the water supply,
check to ensure there are no leaks.
• The water outlet can either be
connected to a water drain or to a
sink outlet spigot. This connection
should be at a minimum of 50 cm and
a maximum of 110 cm from the floor.
Fig. 17
Fig. 18
Fig. 19
23
• The drain hose should be no longer than 4m in length to ensure
good performance from the dishwasher.
• To prevent siphoning, ensure that the water outlet is not pushed
too far into the waste standpipe. The lowest part of the water outlet
should be level with the bottom basket of the dishwasher.
• When connecting to the sink, ensure that the waste pipe runs higher
than the level of the sink bowl to prevent siphoning.
• This appliance is cold fill only.
24
The machine is supplied with a fitting
template and these instructions should
be followed as normal.
Fitting template
X Door height
Where non-standard integrated
appliance doors are supplied, additional
fitting instructions are required to
ensure compatibility with this product.
Y offset
Fitting the Integrated
Appliance Door
Fig. 20
However, the fitting template needs to
be located lower down the fascia door;
this is shown below.
The amount of offset, Y, depends on
the height of the fascia door and can be
calculated as X = 723mm.
For example, if you have a 731mm tall
fascia door and are fitting a door to your
dishwasher, then Y = 731-723 = 8mm.
Ensure that the hinge tensioners are
adjusted to balance the weight of the
door.
25
NOTES:
26
NOTES:
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
27
Serviced by
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Passionate about style
Customer
GroupLtd.
Ltd. • • Harby
HarbyRoad
Road • • Langar
Langar • • Nottinghamshire
Nottinghamshire • • NG13
NG139HY
9HY
CustomerCare
CareDepartment
Department• •The
The
Group
T : 01949
862862
012012
F : 01949
862862
003003
E : customer.care@cda.eu
: www.cda.eu
T : 01949
F : 01949
E : service@cda.eu W : W
www.cda.eu
28