SUGGESTION OF TREATMENT
PACKAGE CONTENTS
INSTRUCTIONS OF USE
• These components are subject to change without
prior notice.
ASSEMBLY
• Appearance of product may differ from the image.
No.
FD-2103
Instruction Manual
VAPOR & COOL MIST
FACIAL STEAMER
PRODUCT
REF.
SKIN TYPES
DIST.
MAINTENANCE
TIME
Greasy skin, poor blood circulation
25cm
15 min
Normal skin
25cm
10 min
Sensitive skin, dry skin
30cm
5 min
Capillary vessel expansion
30cm
5 min
1. Once the steamer unit is cold, remove the water
cup.
QTY
1
FIVE LEG BASE
-
1
2
WHEEL LEG
-
5
3
STRAIGHT POST
-
1
4
SLIDING BAR
-
1
5
TANK SUPPORT
-
1
6
SET SCREW
-
1
7
PRESSING PLATE
-
1
8
FLAT GASKET
-
1
9
GROWER'S SCREW
-
1
10
HEX SCREW
-
1
11
WRENCH
-
1
12
A30
-
1
13
WATER TANK
10054
1
14
SEAL
-
1
15
COOL WATER TANK
10007
1
16
WOOL FELT
-
9
17
SCREW
-
1
18
FILLER LID
-
2
It is advisable to clean your steamer at least once
a week and also to decalcify the water heater
element. Please follow the steps below:
2. Fill the cup with the appropriate decalcification/
water solution and leave it to stand overnight.
CAUTIONS
•
FILLING WITH WATER
Lift up the water tank of the cool sprayer and pour
distilled water into the water cup via the port. Keep
the water level between the “MAX” and “MIN” levels.
When operating the machine, do not point the
nozzle at the customer’s face until the steam is
coming out thinly and evenly.
3. Remove the water and rinse with clean water to
•
The steam should first spray the customer’s jaw
and then the rest of the face.
4. Refill with water and run the steamer through at
FAQ
5. Remove the cup and rinse as before.
If the unit works but does not emit steam.
6. Refill with water and it is ready for use.
•
Note: Failure to remove all the decalcification
residue may cause the steamer to ‘spit’. If this
occurs, simply repeat the rinse and refill procedure
until the issue is resolved.
get rid of any residue from the decalcification agent.
Check that the herb lid is properly closed.
•
Check that the plastic ring is properly placed
between the water cup and the main frame.
least one run cycle in order to remove any remaining
residue from the steamer unit.
•
FRAGRANCE TREATMENT
Pour a little essential oil into the balsam case of the
spray head.
STARTING TREATMENT
1. Turn on the “POWER” button:
Check that the water cup tray is properly
tightened.
•
ACCESSORIES
Check the water level.
If the unit emits steam mixed with hot water.
1. Clean the water cup with vinegar and rinse with
The heater begins to work.
clean water.
After about 6 min, steam will spray out from the
nozzle.
2. Fill the water cup with clean water and add 8 to
10 drops of vinegar. Turn on the steamer for the time
of one operation (do not use it with a patient!).
2. As of this moment, you can turn on the “OZONE”
button:
REF.
DESCRIPTION
10054
WATER TANK
10007
COOL WATER TANK
3. When the operation time ends, turn off the
steamer and rinse the cup with clean water.
The ozone lamp comes on and starts working.
4. Use the steamer during the time of 2 whole
3. Whenever the water level reaches the lower limit,
IMPORTANT NOTICE
EC-DECLARATION OF COMPLIANCE
• Before using the steamer with a customer, it is
very important to perform two entire cycles. Do not
use it with a patient!
This product meets the following requirements:
• It is advisable to wash the new cup vessel
thoroughly before its first use, with clean water only.
1. Conditions set out in the Low Voltage Directive:
2006/95/EC
RECYCLING
• Do not use any substance other than distilled.
Take care when using essential oils or herbs, so as
not to contaminate the water used for steaming.
Whenever any of our electrical products
or their presentation packaging bear this
symbol, it means that these products should not be
treated as conventional household waste in Europe.
To ensure proper treatment of this waste, dispose of
it in accordance with local laws or as required for
the disposal of electrical equipment. This initiative
will help preserve save natural resources and
improve standards of environmental protection in
regard to the treatment of electrical waste.
• NEVER point the vapor jet directly down onto the
client’s face.
• NEVER use the steamer unit in humid or unvented
environments.
OPERATION OF THE COOL SPRAYER
1. Remove the cold water tank. Unscrew the lid
anticlockwise and pour in a metered amount of
distilled water.
2. Conditions set out in the Electromagnetic
Compatibility Directive: 2004/108/EC
WARNING
TECHNICAL SHEET
Adjustments
2. Place the cold water tank in the correct position
and press down.
3. Turn on “MOISTURE”.
4. The water level in the tank will go down to supply
the water that disappears from the cistern while the
spray is operational. Whenever the water level in the
cistern reaches the lower limit and the tank does not
contain enough water to supply it, the main computer
will cut off the power supply off automatically and
stop working. At this time, remove the water tank and
pour in a suitable amount of distilled water. Return
the tank to the cistern to continue working.
• NEVER use the steamer outside.
• NEVER attempt to open the steamer casing/
housing yourself.
• If the power cord was destroyed, please ask
a professional to service and replace it to avoid
hazards, or contact the dealer for service.
• Forbid to work without water, if does, it beyond the
range of warranty.
WELCOME!
Thank you very much for purchase. Please read
the instructions carefully before operating the
instrument. You can also ask a professional for
guidance to make sure you are using the instrument
correctly. We will accept no responsibility for any
accidents that occur due to incorrect operation.
The company reserves the right to amend the
details of the instruments with no prior notice. If any
mistakes are found in these instructions, please feel
free to send us an e-mail informing us so that we
can correct them.
operations with clean water.
turn off the “POWER” button. Lift up the water tank
of the cool sprayer and pour distilled water into the
water cup via the port. Keep the water level between
the “MAX” and “MIN” levels.
Weights and sizes
Upper height limit (cm)
125
Lower height limit (cm)
97
Rotation of arm
-
Rotation of the nozzle
360º
Extension fo the arm (cm)
-
Packing size (cm)
86,5x31,5x31
Gross weight (kg)
8
Material
Methacrylate
Capacity
0,9 l
Working characteristics
Preheat time
6 min. (approx.)
Electrical characteristics
Rated voltage
220V ~ 240V
Frequency
50Hz/60Hz
Rated power
850W
Water tank
FRONT PANEL
5. There is a cap on the bottom to drain tank.
Fragances
Yes
Ozone
Yes
Deposit for herbs
No
Cold spray
Yes
Download PDF