6050 E
1
2
3
4
1
Rinse-aid
Salt
Pre-wash
START/STOP/
CANCEL Half Load
5
6
7
2
3
4
5
30 Minutes
35°C
Economy
50°C
Normal
60°C
Intensive
70°C
8
9
1 TURN ON/OFF, Control LED
4 Programme monitoring LEDs
7 Half Load Button
2 No Rinse-aid warning LED
5 Programme selection knob
8 TURN ON/OFF Button
3 No salt warning LED
6 START/ STOP/CANCEL Button
9 Handle
Function Buttons
Pre-wash
Wash
TURN ON/OFF Button
TURN ON/OFF
When you press the TURN ON/OFF button, the control
LED is turned on at the on position and turned off at the
off position.
START / STOP / CANCEL Button
START / STOP /
CANCEL
The programme you have selected starts as you push
START/STOP/CANCEL button. LED is turned on at Start
position, while it is turned off at Stop position. If you
need to open the door due to any reason during the
programme, press START/STOP/CANCEL button to
stop the programme and restart the programme after
closing the door.
Programme monitoring LEDs
1
Pre-wash
Half Load
2
30 Minutes
35°C
TURN ON/OFF
Monitoring the programme
The steps of the programme can be monitored during wash
programme by the programme monitoring LEDs on the
panel, with the exception that drying monitoring LED is never
on during 30 minutes programme. START/STOP/CANCEL
and Programme monitoring LEDs are off when the
programme you selected ends.
Half Load Button
To turn on your dishwasher with half load, place the
dishes as you wish. First, push TURN ON / OFF button.
Having selected the programme you pefer, push the
Half Load button and see the LED on the button is on.
Start the programme by pushing START/STOP/CANCEL
button. Half Load choice enables you to use all parts of
both the upper and lower baskets and thus you save
power and water.
Rinsing
Drying
Drying monitoring LED is off during 30 minutes
programme.
To remove the water left on the washed items
and in the dishwasher after rinsing and to
protect the resin in the salt container, your
dishwasher will stay for approximately 25
minutes in stand-by mode and then continue
to work starting from drying phase and turn
on the drying LED.
The programme you have selected ends, when
the START/STOP/CANCEL and Programme
monitoring LEDs are off.
Changing the programme
To change the programme as wash programme continues, press
START/STOP/CANCEL button and see if the wash LED on the button
is off.
Select a new programme.
P u s h i n g S TA RT / S TO P / C A N C E L b u t t o n , s e e t h e L E D
on the button is on. Newly selected programme will start.
The new programme will continue from where the cancelled
programme is stopped.
Cancellation of the Programme
To c a n c e l a s t h e p r o g r a m m e c o n t i n u e s ;
push the
START/STOP/CANCEL button and see the LED on the button is off.
Keep pushing START/STOP/CANCEL button for 5 seconds. Stop
when the LED on the button flashes. The water in the dishwasher will
be drained within 45 seconds. The programme will be cancelled,
when the LED on START/STOP/CANCEL button is off.
Then you can select a new programme and start again.
There may be residues of detergent or rinse-aid in the
dishwasher and/or on the washed items depending on the
phase where you have cancelled the programme.
6050 E
The programme you have selected ends, when the
START/STOP/CANCEL and Programme monitoring LEDs are
off.
Operation of your Dishwasher
n
n
n
n
n
n
n
n
n
n
n
Open the tap.
Plug the dishwasher.
Open the door.
Load the dishwasher.
Check whether the upper and lower fan blades can turn freely.
Put sufficient amount of detergent in the detergent container and
close the door.
Push the TURN ON/OFF button, see the LED on the programme
selection knob is on.
Add salt and/or rinse-aid if needed after checking the No Salt and No
Rinse-aid warning LEDs.
Select your wash programme with the help of Information on the
Programme and Average Consumption Values Table.
Select the wash programme by turning the programme selection
knob.
Ensure the programme number on the programme selection
knob aligns the TURN ON/OFF control LED.
Start the programme pressing START/STOP/CANCEL button, see
the led on the button is on.
n You may keep the button you press inserted to avoid your children
to change the programme you have chosen. The position of the
button e.g. whether it is in or out will not effect the programme
flow.
Ensure not to open the door as the dishwasher works. If you need
to open, the safety system will activate and stop your dishwasher.
Be careful of the steam to come out, when you open the door of
your dishwasher. The wash programme will continue, when you
close the door.
To remove the water left on the washed items and in the dishwasher
after rinsing and to protect the resin in the salt container, your
dishwasher will stay quiet for approximately 25 minutes in standby mode and then continue to work starting from drying phase
and turn on the drying LED.
n The programme you have selected ends, when the
START/STOP/CANCEL and Programme monitoring LEDs are off.
n Turn off your dishwasher by pushing TURN ON/OFF button.
n Close the tap.
n Unplug the dishwasher.
Information on Programme and Average Consumption Values Table
Programme no:
1
2
3 Reference
4
5
Programme title:
Pre-wash
30 Minutes
Economy
Normal
Intensive
-
35°C
50°C
60°C
70°C
Wash temperature
-
Not-dried
Coffee, milk
tea, cold
meats,
vegetables
Not-dried
Coffee, milk
tea, cold
meats,
vegetables
Not-dried
soups, sauces
dough
egg, rice
potato
and oven
roastings
Soups sauces
dough egg
rice and
potato
and oven
meals
roastings
-
Less dirty
Moderate
Moderate
Too dirty
Do not use
detergent
A
A+B
A+B
A+B
Pre-wash
35°C Wash
Pre-wash
Pre-wash
50°C Pre-wash
End
Cold rinse
50°C Wash
60°C Wash
70°C Wash
Hot rinse
Cold rinse
Cold Rinse
Cold Rinse
Drying
Hot rinse
Hot Rinse
50°C Rinse
End
Drying
Drying
Hot Rinse
End
End
Drying
Type of leftovers
on the dish
Level of dirt
Detergent Amount
A=25 cm³ / 15 cm³
B=5 cm³
Programme
Flow
End
Duration of
programme (minutes)
Power Consumption
(kW/h)
Water Consumption
(liter)
14
30
150
100
115
-
0,78
1,05
1,26
1,65
4,2
11,8
15
15,8
17,5
Average consumption values are valid for 15°C water inlet temperature.
The pre-wash programme is for rinsing through the dishes that are kept in the dishwasher for a few days.
Values given with the markings on the product or on other printed document provided with the product are obtained in laboratories according
to relevant standards. The values may vary according to operational and environmental conditions.
18 9901 1506-00
050 E
Dishwasher
OPERATING
MANUAL
This product,
is manufactured in modern plants
without causing any harm
to the nature.
s been manufactured in sophisticated premises through the meticulous quality assurance procedures
est possible performance. Please carefully read this Operation Manual and keep it in safe place for
s
iar with Your Dishwasher /
Page 4
Features
6
ades ...................................................5
Features ..............................................5
and Safety Information
Page 6
..............................................................6
Safety.....................................................6
Safety ...................................................6
ormation...............................................7
ergy and Water......................................7
objects to avoid for washing ................7
rst Usage
the Dishwasher
Page 8
..........................................................9
the Dishwasher for
ge
Page 10
he Dishwasher...................................10
Page 10
Function of Water Softener..................................10
How Does the Water Softener Operate ...............10
Filling the Salt ......................................................10
7
Adjusting the Water Softener
System
Page 12
Eliminating the Water Hardness ..........................12
Test Strip..............................................................12
Water Hardness Level Adjustment Table.............13
Regeneration Adjustment Switch.........................13
8
Using Detergent
Page 14
“Two-in-One”, “Three-in-one” Detergents ............14
Filling the Detergent.............................................14
9
Rinse-aid
Page 15
Dosing the Rinse-aid ...........................................15
Page 8
ns, Water Inlet .....................................9
g Hose Inlet .........................................9
ns Water Output ................................10
Water Softener
10
Loading the Dishwasher
Page 16
Lower Basket, Folding Plates ............................16
Divided Cutlery Basket ......................................17
Multi Purpose Height Adjustable Service Basket 18
Bottle Rods .......................................................18
Upper Basket Glass Support Rod ......................19
Height Adjusted Rack........................................19
Adjusting the Height of the Basket .....................19
Dishwasher Loading and
Page 18
llation Information
............................................................18
Rinse - aid .........................................18
Programme........................................18
nce and Cleaning
Page 19
............................................................19
............................................................20
............................................................20
o
oning Call Center
Page 21
washer does not work .........................21
3
miliar with Your Dishwasher / Technical Features
with Rack
1
Track
Adjustment Switch
ades
r Lid
et
ade Slot
ntainer
ade
3
4
7
2
5
6
8
9
11
12
10
el
des
13
14
15
lades
designed for more effective wash of your
l Features
: Standard dinner set for 12 persons
: 85 cm
: 60 cm
: 57 cm
: 52 kg
: 220V, 50Hz
: 2200 W
Heating Power
: 2000 W
Current
: 10 A
Pumping Power
: 125 W
Drainage Pumping Power : 35 W
Power input
Total power
ight to introduce any change in technical details or design without giving any previous notice due to our
dies during production.
years (time period to reserve necessary spare parts in order to preserve the functionality of the
with the Standards and Test Information / EU Conformance Declaration
anufacturing and sales of this machine are done in compliance with the safety rules covered by all relevant
e European Union.
336/EC,
93/68/EC,
IEC 436/DIN 44990, EN 50242
5
ngs and Safety Information
to protect the environment. Certain parts
your diswasher are made of recycling
s the recycling symbol on these materials,
information about the material. (>PE<,
). It is not correct to dispose these material
stead they should be handed over to the
. Please, contact responsible centers and
to take information on disposal methods
nts.
afety
allation done by a licenced electrician.
all not be responsible for any possible
age to be caused by operation without
your fuse is less than 16 Ampere, get a
pere connected by a licenced electrician.
is suitable to work on 220-240 Volt. Let
h the capacity of 110/220 Volt and 3000
n between, if the mains supply at your
olt.
should not be plugged, while installation.
xtension cord.
oated plug provided with the dishwasher.
Keep the detergents far from the reach of the children and
fill in the detergent container just before operating the
dishwasher.
Water in your dishwasher is not drinkable. Therefore, do
not let children play around the dishwasher when the door
is open.
When the dishwasher is installed, make sure that the socket
of the plug is at a reachable point.
When you intend to plug off, only pull back by the plug.
Never pull by the cord.
Children’s Safety
After unpacking the dishwasher, make sure that the packing
material are not placed at the reach of children.
Children should never play on or with the dishwasher.
Do not let children to play around the dishwasher, when
the door is open and do not let them sit on the door.
To prevent possible injuries, either place the long and sharp
items like service fork, bread knife with the sharp ends
down always in the cutlery basket or place them horizontally
on the baskets.
Dishwasher detergents contain irritating and wearisome
substances. Thus, it may cause burning and scalding in
mouth, eyes and throat.
ormation
Operate the Pre-wash programme, at first usage.
is designed only to wash
s.
Our authorised service is not responsible for any
arrangement on your power and sanitary installations. Do
call our authorized service for installation and first operation
after you get your power and sanitary installations arranged
and/or renewed as appropriate for your dishwasher.
Do not place in your dishwasher unsuitable dishware.
Furthermore, do not fill in the baskets more than their
capacity. Otherwise, our company shall not take any
responsibility for possible scratches and rust to be caused
by the movements of the baskets on the inner walls of your
machine. Never put anything else other than the Detergents
and Rinse-aid produced for your dishwasher in the
Detergent and Rinse-aid container of your dishwasher.
Otherwise our company shall not take any responsibility
for any possible defects on your dishwasher.
ble chemicals in the dishwasher
osion risk.
dishwasher and packing materials
according to the rules. Please, make sure
hwasher does not cause any danger to
wn that the children may get locked in old
der to get rid of such troubles, we kindly
t the main power cord and break the lock
event it from getting locked.
e upper and lower baskets out completely,
dishwasher carries all the load of the
heless, do not put other loads on the door.
dishwasher may overturn.
ou closed the door, after you finish your
achine.
t to open the door, as the dishwasher is
eful of the steam to come out when you
asher is installed, the connections should
While installing your dishwasher, make
ck panel do not lean on any place (tap,
pay attention to choose the best place to
asher which you will not later need to
Saving Energy and Water
Clean off all the leftovers from your dishes before placing
them to the dishwasher. Operate the dishwasher when it
is completely loaded. Use the Pre-wash programme only
when really needed. While selecting the programme, pay
attention to the information on the programme and average
consumption values table.
Unsuitable objects to avoid for washing
Never wash the dishes having smoke ash, wax, polish,
paint, chemical substance on in your dishwasher.
Iron alloyed items can get rusty when they are washed in
the dishwasher
7
on the other items.
ks, spoons and knives with wooden or
ms with adhesives, plastic items that are
t, cooper and tin pots in your dishwasher.
nd wash, fading and darkness may occur
e prints of the porcelaines, aluminiums or
ain fine glass types and crystals may
parency during the time. We kindly
to be careful to buy your future dishes
are suitable to wash in the dishwasher.
ncave dishes such as pots, glasses,
e down in the dishwasher in order to avoid
on in these cavities and hollows.
e first usage
ntrol activities at the manufacturing stage
me water left in your dishwasher which
to your dishwasher.
in your dishwasher more than its capacity
hose items that are stated in this manual.
d repair works of your dishwasher should
ut by the authorised service. Any repair
d out by other persons may lead to a
e your dishwasher to get out of the scope
water and power connections of your
made according to the instructions in the
s of this manual. Fill in 1 liter water in salt
dishwasher before first usage.
4 Locating the Dishwasher
Check your dishwasher in terms of any damage caused
during transportation. Do not use a damaged dishwasher.
Consult your manufacturer in the event of any doubt.
As determining the location of your dishwasher, make sure
that you can easily place the dishes in the dishwasher.
Moreover, pay attention to choose a location where you
can easily take out and arrange the dishes. Avoid to locate
the dishwasher at a place where the room temperature
possibly get under zero.
Locate the dishwasher close to the tap and outlets. The
location of the dishwasher should be chosen considering
that the location shall not be changed after the connections
are made.
Before installation, follow the warnings on the packing while
unpacking the dishwasher.
During installation, pay attention not to damage the floor,
walls and pipes etc. Do not hold the dishwasher by the
door or panel for moving the dishwasher.
While locating, pay attention to leave some place at all
sides of the dishwasher to be able to move easily forward
and backward during house cleaning.
While placing the dishwasher, ensure the water inlet and
outlet pipes are not get congested. Furthermore, pay utmost
attention not to crush power cords by the machine.
The dishwasher should be placed on a level ground and
the door should be closed appropriately and tightly.
o the machine stands exactly vertical and
asher is located vertical and straight, the
erlap the inner wall or the frame.
Connecting Hose Inlet
Please do not use the water inlet hose of your previous
dishwasher if available. Instead, use the new water inlet
hose provided with your dishwasher.
st by the legs until the dishwasher is
ght, if the door of the dishwasher is not
has an earthed plug which must be
thed socket of proper voltage and current..
installations made by a certified
company shall not be responsible for any
onal damage to be caused by operation
our fuse in house is less than 16 Ampere,
6 Ampere connected by a licenced
a fuse with 16 Ampere connected by a
an.
you need to replace the power cord,
orised service only. For safety purposes,
ine when the wash programme ends.
ns, Water Inlet
3/4” 1/2” CH
3/4”
DK
min 10
S
3/4”
N
SF
For safety purposes, make sure that you close the water
inlet tap, when the wash programme ends. Connect the
water inlet hose directly to water inlet tap. The pressure
coming from the tap should be at least 0.3 bar and 10 bar
at most. If the water pressure is more than 10 bars, insert
a pressure decreasing valve in between.
The tap should be opened to the end after the completion
of the connections and the impermeability should be
checked.
For safety purposes, make sure that you close the water
inlet after the completion of the wash programme.
he sanitary installation of your house is
install a dishwasher. Moreover, we
nstallation of a filter at the entrance of your
ment so as to prevent any harm to your
e caused by the dirt (sand, clay, rust etc.)
mains or your sanitary installations and
complaints like fading and residue after
9
s, Water Outlet
100
70
80
60
50
40
30
There is a special salt container in the dishwasher which
decreases the hardness of the water.
Function of Water Softener
A dishwasher needs soft water. If the hardness of the
water is higher than 6°dH, it should be softened and the
lime in it should be decreased. Otherwise, ions causing
the hardness shall accumulate on the items which may
have an adverse effect on washing, shining and drying
performance of the dishwasher.
How Does the Water Softener
Operate?
20
10
0
min 50 cm
min 4cm
90
max 110 cm
12cm
e can directly
he water outlet
tlet of the
connection
st 50 cm high
and 110 cm
drainage hose
ters shall lead
110
er drainage hose to the waste water pipe
In order the prevent disconnection of the
ose as your dishwasher is operating,
ater outlet pipe tightly. Water outlet pipe
cted to the drainage, it should have no
ce water.
6 Water Softener
ng the Dishwasher for
sage
he Dishwasher
r location to install your dishwasher. Also
to install your dishwasher at a safe and
ness of the surface can be balanced by
ewed legs. The doors shall be closed
e dishwasher is installed correctly.
ainage connections should be left loose
event any bending or jam.
her should not be operated at a room
under 0 ºC.
As the water passes through the softening system, the
ions causing hardness are eliminated and water gets the
proper softness to give the best result of washing. According
to the degree of hardness of the water, the ions causing
hardness collect quickly in water softening system. In order
to get the same performance at the next wash, therefore,
the softening system should be refilled. This is the objective
of using the dishwasher salt. Such kind of salts are
developed by detergent manufacturers for use in house
type dishwashers.
Filling the Salt
Please use only a special softening salt produced for use
in the dishwasher. (The salt warning LED shall get off,
after first fill of the salt container of the dishwasher.) In
order to fill in softening salt, first pull out the lower basket
and open the lid of the salt container by turning it anti
clockwise A B .
h a funnel in the container D . When you fill in the container put the lid on and close tightly. You can fill
2 kg of softening salt in the salt container.
blet in the salt container, do not completely fill in the container. We recommend you to use softening salt
mall particles or powder. Never use other types of salts that do not dissolve in water such as table salt.
ner may become non-functional by the time. As you turn on your dishwasher, the salt container shall be
er. Thus, fill in the softening salt before you turn on your dishwasher. In order to find out whether the
ning water is enough or not, check the No Salt warning LED on the panel. When the indicating LED on
you should refill the salt container.
B
C
D
er only before first operation C .
nd to start any washing programme immediately after adding some salt, do pre-wash or select a programme
o that the salt spilled out in the dishwasher shall be dissolved and discharged.
11
ing the Water Softener System
Water Hardness
formance of your dishwasher is subject to the softness of the water. For this reason, your dishwasher is
system to decrease the hardness of the water coming from the mains. When this system is adjusted
formance will increase. In order to adjust the system, find out the degree of hardness of the water coming
applying instructions for test band provided with your dishwasher.
b
c
f
1 second
d
1 min.
t water to flow Dip the test strip
m your tap for into water for 1
1 min.
second
e
1 minute
Take the test strip
out of water and
shake it.
Hold on
for 1
minute
Level 1
No Lime
Level 2
Low lime content
Level 3
Lime content
Level 4
Medium lime content
Level 5
Lime content
Level 6
High lime content
Set the water hardness of your dishwasher
according to the result shown by the test
strip.
a different location, the level of water hardness will possibly be changed. It is essential to
r hardness in order to obtain optimum washing efficiency .
hardness adjustment is carried out for your dishwasher, the latest water hardness value shall be shown
he dishwasher for approximately about 5 seconds. Since the Programme Selection Knob is at position
stment indicates level 1 on the panel. Carry out new hardness adjustment of your dishwasher (according
evel of the water at your tap), by means of changing the position of the programme selection knob.
rdness & Regeneration settings
German French * Regeneratio
Position **
s° degrees° degrees° n settings
of Programme
dH
dF
Selection Knob
0-5
0-9
6-11
10-20
1
12-17
21-30
8
18-22
31-40
2
23-34
41-60
5
35-60
61-107
0
1
0
1
0
1
0
1
0
1
0
1
Hardness Level indicator
0
1
1
Pre-wash LED on the panel is on.
0
1
2
Wash LED on the panel is on.
3
Rinsing LED on the panel is on.
4
Drying LED on the panel is on.
5
Pre-wash, Wash, Rinsing, Drying LEDs on the
panel are on at the same time.
5
Pre-wash, Wash, Rinsing, Drying LEDs on the
panel are on at the same time.
0
1
0
1
0
1
0
1
Programme
Monitoring LEDs
Pre-wash
Wash
Rinsing
Drying
the water you use is more than 107°dF (French Hardness) or if you are using pit water, we recommend that you use filters and
r is below 9F (French hardness), you do not need to use special dishwasher salt in your machine. In this case, salt indicator light (if available)
nuously.
es' Programme Knob has 1 / 2 / 3 / 4 positions, you can set the hardness level by turning it to position 5 after the last position clockwise.
on Adjustment Switch
High Lime Content
s Level is 6 (high lime content), turn the
justment switch on position 1 after setting
turning the Programme Knob on position
Set the programme selection knob on position 1, as your dishwasher
is turned off.
Turn on your dishwasher pushing START/STOP/CANCEL button and
then push TURN ON/OFF button and take your hands off from the
TURN ON/OFF button.
Keep pushing START/STOP/CANCEL button for 10 seconds.
Changing the position of programme selection knob, you can change
hardness adjustment levels according to the table below.
Having selected the level of hardness, push the START/STOP/CANCEL
button once more to record the selected adjustment to the memory.
Turn off your dishwasher by pressing TURN ON/OFF button.
13
Detergent
use only the detergents specially produced
.
the detergent, keep your detergent at a
where your children can not reach.
nt in the detergent container before you
washer.
detergent may lead to non-dissolution of
hich may create scratches on the glass
are divided into two groups as including
n-including phosphate. Both of them can
dishwasher.
compact powders normally do not include
ce phosphate has a softening effect in
mmend you to use salt if the hardness of
hen you are using detergent of such type.
osphate detergent is used in a region
ess of the water is high, white spots may
shes and glass items. You should use
to prevent this.
t of the non-chlorine detergents is lower.
pots may not be completely cleaned. In
this, you should use a high-temperature
e or a detergent including chlorine.
nformation on the detergent you are using,
ontact the detergent manufacturers.
formed detergents, please see information
urer instructions on the package of the
where on the dishwasher you should put
gent container, basket etc.).
“Two-in-one” or “Three-in-one”
Detergents
Generally, detergents including rinse-aid and/or softener
can only give good results under certain using conditions.
Such detergents include rinse-aid and/or softener in
standard, formerly amounts. Therefore, it is not possible
to carry out water softening and rinse-aid amount adjustment
according to the hardness of the water in your house. For
use of such detergent, you should get in contact with the
manufacturing companies of your detergent and learn the
proper using conditions.
If you are not satisfied with the result of a washing and/or
drying with a given “Two-in-one” or “Three-in-one” detergent,
contact the manufacturer of the detergent. The Guarantee
of your dishwasher does not cover complaints caused by
the use of such detergents.
Filling the Detergent
To open the lid of the detergent container, push the latch
to right A .
There are level indicating lines in the detergent container.
The total capacity of detergent container is 40 cm³. Using
these lines, you can determine the correct amount of
detergent to be filled 1 .
If your dishwasher is completely full or your dishes are
very dirty, use level 25cm³; if it is not completely full or your
dishes are not so much dirty, use level 15cm³ 1 .
If your dishes are kept waiting for a long time before
washing, also fill in the detergent slot of 5 cm³ 2 .
e kept waiting for a long time and the
dishes are dried, fill in 5cm³ more detergent
container. You can see the correct amount
he Programme Information and Average
lues Table for the wash programme you
need to fill in more detergent depending
of your dishes or water hardness level at
Push the latch
to the right
Wipe and clean the rinse-aid spilled over the container.
The rinse-aid spilled over by fault leads to foaming and
thus decreases the washing performance.
By controlling the warning indicator on the control panel,
you can decide whether to add rinse-aid or not 4 . The
dark color of the warning indicator indicates that the rinseaid amount is sufficient. If it is not dark colored, please add
rinse-aid.
2
1 25cm³
15cm³
4
5cm³ 2
Aid
a special chemical used to increase the
nce or to prevent water marks or lime
s. The rinse-aid is used not to have the
more but to have them at sufficient drying
of wash programme. Therefore, be sure
in the rinse-aid container and to use only
oduced for dishwashers.
e-aid, open by pressing the latch of rinse•. Fill in the container up to level MAX and
.
Do not forget to close the rinse-aid container lid after filling
in the rinse-aid container 3 .
B
3
5
Dosing the Rinse-Aid
Rinse-aid doser can be adjusted to positions between 1
to 6. The factory adjustment is position 3 5 .
If there are water streaks on the dishes after washing, the
degree should be increased, while it should be decreased
with the blue streaks that are erased by hand.
15
ng the Dishwasher
shes in a proper way, you get maximum
om your dishwasher in terms of power
washing and drying performance.
he dishwasher, sweep any residuals off
eeds etc.) on the dishes. There are two
s in your dishwasher for you to load your
dirty and large items on the lower basket
te and light items on the upper basket.
ave dishes such as pots, glasses,
de down in the dishwasher.
e to put long and narrow items on the
sket.
ble injuries, either place the long and sharp
fork, bread knife always sharp ends down
sket or place them horizontally on the
A
1
B
2
B
4
3
1
2
4
3
sket
ates
s of four parts provided on the lower basket
her are designed for big items such as
s etc. more easily 1 2 3 4 . You can
s by means of folding each part or all of
You can use the folding plates by raising
s first and then leaning them B forwards.
Lower basket
Upper basket
Alternative example to fill in the basket
utlery Basket
number of items and dirt type, divided cutlery basket part can be separated into three parts and smaller
art can be placed on the upper basket 2 . To separate the cutlery basket, turn the latches under the handle
aller cutlery basket upwards and pull out the upper and lower latches B . To combine the parts again,
e order of separation process.
A
B
utlery and soup ladle can not be placed to the upper basket in the cutlery basket. Such parts should be
cks. For better washing and drying efficiency, usage of separators is recommended 3 4 . These parts
when not needed C D .
4
D
C
2
he big items like saucepan and tray, you can take out the cutlery basket.
17
ose Height Adjusted Basket
n your dishwasher’s lower basket enables you easily wash your extra glasses or the items like soup ladle
ks, fold the rack A . Slide up the rack B . Get the rack in vertical position C . Slide down the rack and
hes D . You can open the rack by following the reverse order of the process. To make the racks' height
the rack E . Slide up the rack F . Open the rack at the preferred level G . Make sure that the fan blades
dishes you have placed on the racks.
D
D
G
D
E
F
H
ds
esigned for easier washing of high items with wide mouth. In order not to use bottle rods, you can
ling H from the both sides
ket
port Rods
e long glasses and wine glasses, do not lean them on other items but to the edge of the basket, to the
ss support rod 1 . Be careful not to lean long glasses to eachother since they can not stand still and may
ing washing.
support rod to the horizontal position A B .
usted Rack
adjusted racks on the upper basket of your machine which are easily adjusted by shifting up and down
height of your glasses, cups and similar objects C D E .
he Height of the Basket
sting Mechanism on your dishwasher's upper basket enables you to create larger areas in your dishwasher's
baskets by your needs without removing the basket from your dishwasher when your upper basket is
hwasher's basket is adjusted to down position by default. To raise your basket F hold and raise up one
plates (left or right). To raise the other part of the basket, do the same. To lower your basket, hold and G
your Loaded Basket Adjusting Mechanism (left or right) to get the lower position. To lower the other part
the same process. Make sure that the both sides of the Loaded Basket Adjusting Mechanism are at the
or high).
E
D
C
F
G
19
ard Dishwasher Loading and Test Installation Information
basket
Upper basket
baskets: 12 different units. The upper basket is put to the lowest position for the standard test.
se aid
DIN 44990 IEC 436 as per (international norms)/Dosing of Rinse-aid: 5
gramme
EN 50242 as per (international norms)
1
2
3
3
1
1
3
3
2
2
2
2
3
3
1
2
2
1
3
6
4
5
4 1
5
4
4
4
5
4
5
5 1
5
4
5
6
7
8
8
1
4
4
5
5
4
4
4
4
5
5
5
5
3
1
2
2
1
3
3
2
2
2
2
3
3
7
1
3
1
7
enance and Cleaning
hwaser is cleaned at regular intervals, the
will be extended and frequenly occurring
essened. Clean the fan blades and filters
a week.
Clean all three filters with a brush under tap water. Place
the metal / plastic filter in its place. Place the coarse filter
in the micro filter. Make sure that they are placed correctly.
Turn the coarse filter clockwise until the „click” sound is
heard. It is essential to place the filters correctly.
The dishwasher should not be used without filter.
g the dishwasher and close the tap before
The wrong placing of the filters will decrease the washing
performance.
outer surface and door gaskets of your
a soft cleaning material and damp cloth.
only be rubbed with a slightly dump cloth.
material for cleaning.
Cleaning the filters is essential for proper operation of
the dishwasher.
and fan blades regularly so that your
effectively. Check the coarse and fine
duals accumulation. If there are leftovers,
s and clean well under tap water.
B
A
1
separate filters in your dishwasher.
c filter
micro filter and coarse filter group for
e, first turn it anti clockwise and take out
out metal / plastic filter B . Later on, push
s on the coarse filter to take out the coarse
C
2
3
21
s
he holes of Lower 1 and Upper fan blades 2 3 are clogged or not. If there is a clog, take out
nd clean them. By pulling up lower fan blade A B ,
the nuts of Upper and Top fan blades by means of turning the nuts to left. C D .
back the upper and top fan blades, make sure that the nuts are exactly screwed.
B
D
2
C
C
3
D
r
to your dishwasher to be caused by the dirt (sand, clay, rust etc.) coming from the mains or your
ions are hindered with the help of a filter. Check the filter and the hose sometimes and clean if
n the filter, close the tap first and take out the hose. After taking out the filter from the hose, clean
. Place the cleaned filter back in its place in the hose and connect the hose on its place.
o do before Phoning the Call Center
hwasher does not work;
er the dishwasher is plugged or not.
ses in your house.
at water inlet tap is open.
at you closed the door of your dishwasher.
at you turned on the dishwasher by the TURN ON/ OFF button.
at the water inlet and the filters in your dishwasher are not clogged.
ntinues, phone the Call Center.
23
Download PDF