® plumbing and heating products Plumbing and Heating Marking Seven Decades Of Dedication To The Plumbing And Heating Industry Look around Conbraco and you’ll see our commitment to serving the plumbing and heating industry is as strong today as it was seven decades ago when we filled our first order. As the industry has grown, so has our lineup. Today, we’re designing and producing more than 120 distinct products under the Conbraco, Apollo®, RP&C® and Apollo International brand names. From our nearly 1.5 million square feet of ISO 9001 certified space, we’re turning out world-class safety and shut-off valves, relief valves, backflow preventers, Product Family Index strainers, pressure reducers and accessories. Plus the most comprehensive line of U.S. made ball valves. It’s a product selection so complete, our customers can enjoy single-source convenience and accountability on products that meet or exceed stringent ASME, UL, CSA, AWWA, ASSE and IAPMO quality and performance standards. With fast deliveries from stocked regional inventories coordinated by our network of more than 2,000 distributors. We’re investing in the future, too. Our $20 million foundry complex in Pageland, SC is among the most advanced casting facilities in the world. By combining continuous-casting technology, backup systems and process controls, the foundry produces brass, bronze and specialty castings with unmatched efficiency, consistency and speed. Count on Conbraco for high-performance products at Pressure Relief Valves ..........................................................................................4 Temperature and Pressure Relief Valves ..............................................................5 Water Heater Accessories ....................................................................................6 Hydronic Heating Specialties ................................................................................9 Pressure Reducing Valves ..................................................................................14 Vacuum Breakers................................................................................................ 17 Backflow Preventers ............................................................................................19 In-Line Check Valves ..........................................................................................24 Pipeline Strainers ................................................................................................26 Section IV ASME Hot Water Boiler Safety Relief Valves......................................29 Section IV ASME Low Pressure Steam Safety Relief Valves ..............................31 Section VIII ASME Safety Valves ........................................................................33 Section I & VIII ASME Safety Valves ..................................................................34 Section VIII ASME Safety Relief Valves ..............................................................38 Gas Cocks/Pilot Cocks ........................................................................................40 Water Gauges and Accessories ..........................................................................44 Air and Drain Cocks ............................................................................................53 Bar Stock Needle Valves ....................................................................................57 Miscellaneous Products ......................................................................................58 All products, services and systems will be constantly improved to enhance our recognition for leadership and excellence by our customers and our industry. This requires that we clearly determine our customers’ requirements and consistently meet or exceed those requirements. highly competitive prices. 2 Customer Service 1-704-841-6000 Plumbing and Heating Product Number Index Series/Part No. Page 10 ................................................29 10-322 ........................................ 33 10-512 ........................................ 33 10-600 ........................................ 30 12-200 ........................................ 31 13 .............................................. 32 14-200 ........................................ 32 14-290 ........................................ 58 15 .............................................. 33 16 ................................................ 4 16-ARV ........................................ 5 16-XT ............................................9 16-501 .......................................... 4 16-601 .......................................... 4 17 .............................................. 30 18 .............................................. 31 18-402X........................................ 5 18-500 .......................................... 5 19 .......................................... 34-35 119 ............................................ 37 20-100 ........................................ 44 20-150 ........................................ 44 20-200 ........................................ 45 20-250 ........................................ 45 20-300 ........................................ 45 20-350 ........................................ 45 20-400 ........................................ 46 20-410 ........................................ 46 20-600 .................................. 47, 48 20-700 ........................................ 46 20-710 ........................................ 46 20-800 ........................................ 47 21 .............................................. 48 23-400 ........................................ 50 23-450 ........................................ 50 23-600 ........................................ 47 24-300 ........................................ 49 24-600 ........................................ 48 24-650 ........................................ 48 25-200 ........................................45 25-400 ........................................45 25-500 ........................................45 25-600 ........................................ 48 26-100 ........................................ 52 26-300 ........................................ 52 26-500 ........................................ 53 26-700 ........................................ 53 27 ................................................ 9 27-400 ........................................58 28-400 ........................................ 59 28-600 ........................................ 59 29 ........................................ 35, 36 3T-WMV ......................................58 31 ................................................ 6 31-200 .......................................... 6 31-401 .......................................... 7 31-500 .......................................... 6 31-600 .......................................... 7 31-700 .......................................... 7 31-800 .......................................... 7 31-900 .......................................... 7 34A/34H ......................................10 34B ............................................11 34C..............................................11 34D..............................................12 35 ................................................ 9 35FC............................................12 35FV ..........................................12 35-200 ........................................ 59 35-300 ........................................59 35-403 ........................................10 35-6A3.......................................... 9 35-6H3 ........................................ 9 36 .............................................. 14 36A..............................................16 36C ............................................ 15 Customer Service 1-704-841-6000 36H ............................................ 16 37 ................................................ 6 38-100 ........................................ 17 38-200 ........................................17 38-300 ........................................ 17 38-400 ........................................ 18 38-502 ........................................ 18 39-100 ........................................ 59 40-XT ............................................8 40-100 ........................................ 19 40-200 ........................................ 20 4C-100 ........................................18 4J-400 ........................................22 4P-300........................................ 21 4V-500 ........................................ 23 4W-500........................................23 40-300 ........................................ 21 40-400 ........................................ 22 40-500 ........................................ 22 40-600 ........................................ 23 40-700 ........................................ 24 41 .................................. 53, 54, 55 41 - Heavy.................................. 55 41 - Extra Heavy ........................ 55 42-100 ........................................ 56 43-100 ........................................ 56 44-100 ........................................ 60 45-100 ........................................ 60 45-201 ........................................ 60 45-301 ........................................ 60 46-100 ........................................ 42 50 .............................................. 42 500 Series ......................38, 39, 40 51 .............................................. 42 52 .............................................. 43 53 .............................................. 43 54 .............................................. 43 55-302 ........................................ 43 56 .............................................. 44 57 .............................................. 13 58 .............................................. 13 59 .............................................. 26 59-300 ........................................ 27 59V ............................................ 27 60 ................................................57 61-100 ........................................ 24 61-200 ........................................ 24 61-500 ........................................ 25 61-600 ........................................ 25 61-700 ........................................25 62-100 ........................................ 25 62-500 ........................................ 25 64 .............................................. 62 70-100-BC.................................. 26 78-124/125 ................................ 60 78—RV ........................................ 8 78-668 ........................................13 95A..............................................62 141/143 ......................................61 Air Gap Drain ..............................20 DC ..............................................19 Drip Pan Elbows..........................38 FC1 ............................................ 28 FC2 ............................................ 28 GB-10 ........................................ 40 GB-12/13/14/15/16......................41 GB-50/50A ................................ 41 IBV-125 ...................................... 61 IBVD-125 ....................................61 IBVE-125 .................................... 61 Jump Kits ....................................14 Jump Kits ....................................15 TCG............................................ 27 Tublr. Gauge Glass Protector ....50 TV .............................................. 10 W-8078-00 ..................................16 3 Plumbing and Heating Pressure Relief Valves Pressure Relief Valves 16 Series Pressure relief valves relieve excess pressure in cold water storage tanks and water supply lines. • • • • Bronze body Standard pressure settings from 50 to 175 psig Stainless steel spring 16-200 Series for pressure relief only, less lever, silicone seat No. 16-201 16-202 16-203 16-301 16-302 16-401 16-402 B A D C 16-200 16-501 Series Size 1/2 M x 3/8 F 1/2 M x 1/2 F 3/4 M x 1/2 F 1/2 M x 3/8 F 1/2 M x 1/2 F 1/2 M x 3/8 F 1/2 M x 1/2 F • 16-300 Series for temperature relief with 210°F fusible plug and pressure relief with lift lever, nitrile seat • 16-400 Series for temperature relief with 210°F fusible plug and pressure relief, less lever, nitrile seat Wt./100 (lbs) 36 33 37.5 37.5 37.5 37.5 34.4 A (in.) B(in.) 1-13/32 1-13/32 1-13/32 1-13/32 1-13/32 1-13/32 1-13/32 2-1/8 2-1/8 2-1/2 2-1/2 2-1/2 2-1/8 2-1/8 C(in.) D(in.) 1 1 1 1 1 1 1 1/2 1/2 5/8 7/8 7/8 1/2 1/2 Note: When ordering, specifypressure by adding th two digit key number after the product number as follows: 50 PSIG: -01; 75 PSIG: -02; 100 PSIG: -03; 125 PSIG: -04; 150 PSIG: -05; 175 PSIG: -06 16-300 By-Pass Relief Valve Protects equipment by allowing excess volume to be discharged to storage tank or back to the source. Ideal for agricultural sprayers and simple process systems. “T” handle facilitates adjustment. • 1/2" size for low volume relief or by-pass control • Adjustable pressure setting No. 16-501-01 16-501-02 16-501-25 16-501-60 16-601 Series Size Wt./each Relief Range 1/2 M x 1/2 F 1/2 M x 1/2 F 1/2 M x 1/2 F 1/2 M x 1/2 F .621 .610 .621 .610 0 - 250 250 - 600 0 - 250 300 - 600 Seat Material Nitrile Nitrile PTFE PTFE Thermal Expansion Relief Valve Protects plumbing fixtures and extends water heater life by relieving excess pressure caused by thermal expansion. Installs fast without special tools or shutting off the water. • Bronze body construction • Stainless steel puncher, spring, clamp No. 16-601-02 16-601-E6 16-601-03 16-601-04 4 Customer Service 1-704-841-6000 • Compact, lightweight, corrosion resistant • U.S. Patent No. 5,241,981 Set Pressure (PSIG) 75 85 100 125 Wt./each (lbs) 0.5 0.5 0.5 0.5 Plumbing and Heating Pressure Relief Valves 16-ARV Series Calibrated Pressure Relief Valves Calibrated valves for easy pressure adjustments without a gauge. Factory preset at 100 psig; accommodates pressures from 50 to 175 psig, marked in 25 psi increments. • For cold water applications • Inlet sizes: 1/2" or 3/4" NPT, both with 1/2" NPT outlet • Cast bronze body, brass disc and cap No. 16-503-01 1/2 ARV 16-504-01 3/4 ARV • Stainless steel spring • Silicone rubber seat and EPDM rubber cap seal Size A (in.) B(in.) 1/2 M x 1/2 F Wt./100 (lbs) 37 C(in.) D(in.) 1-9/32 3-7/16 1 9/16 3/4 M x 1/2 F 38 1-9/32 3-7/16 1 9/16 Temperature and Pressure Relief Valves 18-402X Series Extended Shank Water Heater T&P Relief Valves Relief valves with an extended body length (2") for protection of water heaters with extra insulation. Unique non-metallic coating resists galvanic and electromechanical corrosion. CSA design certified at all settings. ASME Section IV rated at 125 psig and 150 psig settings. • • • • Meets HUD/FHA requirements Cast bronze body, stainless steel spring Rated to 210°F maximum ASME capacity certified to 450,000 BTU/HR. No. 18-402X-02 18-402X-15 18-402X-39 18-402X-38 18-402X-40 18-500 Series • Zinc-plated lever standard • CRN #0G2663.1C registered in all Canadian provinces and territories Size 3/4 M x 3/4 F 3/4 M x 3/4 F 3/4 M x 3/4 F 3/4 M x 3/4 F 3/4 M x 3/4 F Element Length 3 3 3 3 3 Wt./100 (lbs) 64.4 64.4 64.4 64.4 64.4 Pressure PSIG 75 100 125 150 175 CSA Capacity Rating BTU/HR 100,000 100,000 100,000 100,000 100,000 Corrosion Resistant Commercial T&P Valves Diaphragm type high capacity CSA design certified; ASME Section IV certified to 150 psig; ANSI Z21.22 certified to 150 psig. Corrosion resistant with all bronze body and screw-in cage. Eliminates rusting steel screws. Stainless steel springs and thermostats. • Available in set pressures of 75, 100, 125 and 150 psig • The 3/4'' valve can be supplied with 3'', 5'' or 8'' thermostats • Valves 1'' and larger available with 4” and 8” thermostats • 3'' element is CSA capacity certified at 185,000 BTU/HR. • CRN #0G2663.1C registered in all Canadian provinces and territories A B C No. 18-511 18-512 18-521 18-522 18-531 18-532 18-541 18-542 18-551 18-552 Connection 3/4M x 3/4F 3/4F x 3/4F 1M x 1F 1F x 1F 1-1/4 M x 1-1/4 F 1-1/4 F x 1-1/4 F 1-1/2M x 1-1/2F 1-1/2F x 1-1/2F 2M x 2F 2F x 2F A(in.) 4.67 4.67 6.63 6.63 6.63 6.63 9.69 9.69 9.69 9.69 B(in.) 1.85 1.85 2.32 2.32 2.32 2.32 3.34 3.34 3.34 3.34 C(in.) 1.38 1.38 1.93 1.93 1.93 1.93 2.50 2.50 2.63 2.63 Wt./100 (lbs) 106.7 106.7 287.3 284.1 337.2 322.4 819.6 841.7 860.1 874.1 CSA Cap. Rating BTU/HR 205000 205000 765000 765000 850000 850000 1300000 1300000 1400000 1400000 *ASME Rating BTU/HR 1601000 1601000 4200000 4200000 4586000 4586000 7763000 7763000 9262000 9262000 * National Board certified capacity at 150 PSIG per ASME Section IV-Heating Boilers; specify number,thermostat length and set pressure when ordering. EX: 18-511-3-150 Customer Service 1-704-841-6000 5 Plumbing and Heating Vacuum Relief Valves 37 Series Vacuum Relief Valves for Water Heater Protection Automatically vents a system if a vacuum should occur. Prevents siphoning of the water from the system and collapse of a tank. Design certified by CSA in accordance with ANSI Z21.22. Also suitable for low pressure (15 psig maximum) steam service. • Maximum temperature: 250°F • Rated for water pressures to 200 psig • Model 37-100 bronze body (silicone rubber seat) or Model 37-200 brass body (EPDM rubber seat) No. 37-101 37-102 37-201 37-202 37-302 37-100 • Auto-vacuum relief at less than 1/2" vacuum • Venting capacity as measured in cfm of air @ 2" mercury (vacuum) Size(in.) Venting Capacity 1/2 3/4 1/2 3/4 3/4 14 CFM 19 CFM 15 CFM 16 CFM 14 CFM Wt./100 (lbs) 66.0 67.5 30.4 32.4 17.0 Suffix key: Satin Brass - 01; Satin Chrome - 02 *NOTE: This valve is not designed for anti-siphon backflow prevention. To prevent back-siphonage of polluted water into a potable water system, choose from Conbraco’s line of backflow preventers. 37-200 37-302 Water Heater Accessories Water Heater Drain Valves Special packing seal for easy turns and leak-proof operation. Wheel options: zinc-plated steel, chrome finished steel and red-painted aluminum. Models 31-401, 31-600, 31-700 & 31-900 comply with CSA requirements. 31-200 & 31-500 Series • Maximum temperature: 250°F • Pressure rated to over 100 psig • Brass packing nut Wheel Options: Specify wheel type by using the following two digit key number following the product number: 01 - steel, 04 - aluminum, 07 - polished chrome, 10 - tee, 13 - slotted stem 90-Degree Drain Valves For deluxe water heaters, low pressure boilers. • All cast bronze bodies • 31-200 Series heavy pattern, 3/4" MNPT inlet , aluminum wheel only • 31-500 Series standard pattern, 1/2" NPT, three wheel types available (01 - steel, 04 - aluminum, 07 - polished chrome). I.D. NPT of thread machined for 1/2 copper pipe 31-202-04 6 No. 31-202-04 31-212-04 31-501-04 Customer Service 1-704-841-6000 Shank Length(in.) 5/8 15/16 5/8 Wt./100 (lbs) 43.0 46.5 31.0 Plumbing and Heating Water Heater Accessories 31-401 Series Combination Tee & Drain Valve Permits supplying and draining of water through a single tank tapping; meets CSA requirements. • All cast bronze bodies • Wheel options • Pressures to 100 psig; temperatures to 250°F • 3/4" FNPT inlet x 3/4" male hose end x 3/4" FNPT side outlet No. 31-401-01 31-401-07 Description Steel Handle Chrome Handle Wt./100 (lbs) 62.0 62.0 Female Thread Standard Hose 3/4 NPT Wt./100 (lbs) 35.0 35.0 31-401-07 31-800 Series Female Inlet Drain 1/8” NPT Side Outlet Side outlet can be used to feed other systems. • All cast bronze bodies • Ideal design for adding pressure gauge No. 31-801 31-802 31-801-04 31-600, 31-700 Angled Body Water Heater Drain Valves & 31-900 Series Models with 3/4" MNPT inlet (31-600); 1/2" or 3/4" FNPT inlet (31-700); 1/2" MNPT inlet (31-900). • • • • • 31-600 series 31-900 series All cast bronze bodies Meet CSA requirements Various shank lengths available Pressure rating in excess of 100 psig All of our drains are equipped with Conbraco packing No. 31-600 31-601 31-602 31-604 31-606 31-607 31-608 31-609 31-610 31-611 31-612 31-900 31-700 31-701 Inlet 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 3/4 MNPT 1/2 MNPT 1/2 FNPT 3/4 FNPT seal assuring easy turning stem and leakproof drain • Drains are furnished with zinc plated steel, chrome finished steel or red painted aluminum wheels • Maximum temperature 250°F Shank Length 5/8 3/4 1 1-1/4 1-1/2 1-3/4 2 2-1/4 2-1/2 2-3/4 3 5/8 3/4 3/4 Wt./100 (lbs) 27.3 36.0 35.0 43.0 49.5 48.0 52.0 52.0 57.2 60.0 66.3 34.0 39.0 37.0 31-700 series Customer Service 1-704-841-6000 7 Plumbing and Heating Water Heater Accessories 40-XT Series Expansion Tanks for Potable Systems Designed to protect closed water supply systems, appliances and piping from the hazards of thermal expansion, such as premature water heater failure. Installs easily on direct fired gas, oil and electric hot water heaters and storage tanks. Their pre-pressurized steel design includes an expansion membrane that stops any contact between the water and air in the tank. • Ideal for use in dorms, apartments, office buildings and hospitals • Maximum working pressure: 150 psig • 100 percent non-metallic noncorrosive water reservoir • Field-adjustable pre-charge • Compatible with most standard water heaters and storage tanks 3/4 NPT No. 40-XT1-01 40-XT3-01 40-XT5-01 40-XT7-01 A Capacity (gal.) 2.11 4.76 6.34 13.21 Exp. Vol. (gal.) 1.40 3.17 4.22 8.82 Connection 3/4 NPT 3/4 NPT 3/4 NPT 3/4 NPT A(in.) 10.88 13.75 15.88 20.00 B(in.) 8.00 10.75 12.00 15.00 Net Wt. (lbs) 5.5 8.1 9.7 23.4 B 78-RV Series Bronze Water Heater Shut-Off Valve with Thermal Expansion Control Valve Thermal expansion protection and water heater shut-off in a single, simple installation. Space-saving and less costly alternative to large expansion tanks for avoiding potential hazards in closed systems • • • • • • • Sweat and threaded connections available Corrosion-resistant all-bronze body Chrome-plated ball Stainless steel fasteners and springs Bubble-tight shut-off 3/4" listed with IAPMO Now available in 1" size Sweat No. 78-304-RV 78-314-RV 78-324-RV 78-305-RV 78-315-RV 78-325-RV 78-306-RV 78-316-RV 78-326-RV 78-307-RV 78-317-RV 78-327-RV 78-504-RV 78-514-RV 78-524-RV 78-505-RV 78-515-RV 78-525-RV 78-506-RV 78-516-RV 78-526-RV 78-507-RV 78-517-RV 78-527-RV 8 Threaded No. 78-404-RV 78-414-RV 78-424-RV 78-405-RV 78-415-RV 78-425-RV 78-406-RV 78-416-RV 78-426-RV 78-407-RV 78-417-RV 78-427-RV 78-604-RV 78-614-RV 78-624-RV 78-605-RV 78-615-RV 78-625-RV 78-606-RV 78-616-RV 78-626-RV 78-607-RV 78-617-RV 78-627-RV Customer Service 1-704-841-6000 • Control valve’s hose barb fitting, 1/2” pex fitting, compression fitting or 1/2” combination sweat/thread fitting makes discharge piping assembly easy • Expansion control valve taps into side of shut-off valve • Listed with SBCCI PST & ESI Control Valve Drain Outlet hose barb hose barb hose barb pex fitting pex fitting pex fitting compression fitting compression fitting compression fitting 1/2'' combo swt./thd. fitting 1/2'' combo swt./thd. fitting 1/2'' combo swt./thd. fitting hose barb hose barb hose barb pex fitting pex fitting pex fitting compression fitting compression fitting compression fitting 1/2'' combo swt./thd. fitting 1/2'' combo swt./thd. fitting 1/2'' combo swt./thd. fitting Size(in.) 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 1 1 1 1 1 1 1 1 1 1 1 1 Setting 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig 125 psig 100 psig 80 psig Plumbing and Heating Hydronic Heating Specialties 16-XT Series Expansion Tanks for Hydronic Systems Conbraco non-potable expansion tanks help maintain balanced pressure throughout a hot water heating system by absorbing thermal expansion. Pre-pressurized, they’re designed to prevent system damage and unnecessary discharges by relief valves and ensure long, trouble-free system life. • • • • Welded steel construction Rugged flexible diaphragm Pre-charged at 12 psig Compact design saves energy and space 1/2'' NPT A No. 16-XT1-01 16-XT3-01 16-XT5-01 16-XT7-01 Capacity (gal.) 2.11 4.76 6.34 13.21 • Glycol compatible • Maximum working pressure: 150 psig • Ideal for peak use systems such as car washes, processing plants, hotels/motels, commercial laundries Exp. Vol. (gal.) 1.77 3.99 5.31 11.06 Connection 1/2 NPT 1/2 NPT 1/2 NPT 1/2 NPT A(in.) 10.88 13.75 15.88 20.00 B(in.) 8.00 10.75 12.00 15.00 Net Wt. (lbs) 5.5 8.1 9.7 23.4 B 27 Series Radiator Air Valve No. 27-202-02 H-2404-00 35 Series Wt./100 (lbs) 2 .9 Size 1/8 Key only All Bronze Feed Water Pressure Regulator Available in 1/2" union threaded, threaded and solder union configurations. Purge lever/fast fill feature. Cartridge replaceable in-line. • No cage screws • Individually set at 15 psig - Adjustable 10 to 25 psig • Temperatures to 210°F No. 35-503-01 35-603-01 35-703-01 35-6A3 & 35-6H3 Series Size 1/2 Union Threaded 1/2 Threaded 1/2 Solder Union • High capacity • SS strainer, in-line, standard • Choice of inlet connections Ht. 5-1/4 5-1/4 5-1/4 Length 4-5/16 3-1/2 3-3/16 Wt./100 (lbs) 255 225 232 Length 8-1/2 8-1/2 Wt./100 (lbs) 450 440 All Bronze Combination Backflow Preventer & Feed Water Regulator Positive protection against backflow when supply pressure falls below system pressure. • Designed for continuous pressure, hot or cold water service No. 35-6A3-BF 35-6H3-BF Size 1/2 Union NPT x NPT 1/2 Solder Union x NPT Customer Service 1-704-841-6000 Ht. 5-1/4 5-1/4 9 Plumbing and Heating Hydronic Heating Specialties 35-403 Series Multi-Orifice Control Valve Provides flow control on tankless heaters; for delivery of 2-1/2, 3, 3-1/2, and 4 GPM. Easy adjustment. • Maximum temperature: 250°F No. 35-403-01 TV Series • Maximum pressure: 150 psig Size 1/2 Solder Ht. 2.11 Wt./100 (lbs) 42.8 Length 2.00 Mixing Valves Designed to provide extension of water heater capacity and hot water temperature control. For residential applications. Numbered indicator control allows easy setup and fingertip control. Available in low or high temperature options depending on application. • Low temperature range (100°-130°F) • High temperature range (110°-150°F) • Stainless steel spring and rings Size(in.) 1/2 3/4 1/2 3/4 • Bronze body • Thermoplastic shuttle assembly • Thread or solder connections Low Temp. 100˚-130˚ 35-203-L1 35-204-L1 35-205-L1 35-206-L1 Connection Solder Solder Threaded Threaded High Temp 110˚-150˚ 35-203-01 35-204-01 35-205-01 35-206-01 Wt./100 (lbs) 88 101 88/99.5 113 Repair Kits add (-RK) suffix to corresponding part no. 34A & 34H Series Thermostatic Mixing Valves 34A Series are ASSE 1017 certified mixing valves designed for hot water distribution systems; 34H Series are designed for radiant heat applications, to provide better control of hot water supply. Numbered indicator control allows easy setup and fingertip control. Available in low or high temperature range options depending on application. Integrated check provides added protection of thermostat and cross connection control. • Low temperature range (85°-120°F) • High temperature range (120°-180°F) • Stainless steel spring • Bronze body • Thermoplastic shuttle assembly Size 1/2 1/2 3/4 3/4 1 1 1/2 1/2 3/4 3/4 1 1 10 Connection Sweat Thread Sweat Thread Sweat Thread Sweat/Check Thread/Check Sweat/Check Thread/Check Sweat/Check Thread/Check Customer Service 1-704-841-6000 • • • • • • Supply pressures to 125 psig Union threaded or solder connections Integrated check High flow capacity Broad temperature range Cold water failure protection Low Temp. 85˚-140˚ 34A-103-01 34A-103-02 34A-104-01 34A-104-02 34A-105-01 34A-105-02 34A-113-01 34A-113-02 34A-114-01 34A-114-02 34A-115-01 34A-115-02 High Temp 120˚-180˚ 34H-103-01 34H-103-02 34H-104-01 34H-104-02 34H-105-01 34H-105-02 34H-113-01 34H-113-02 34H-114-01 34H-114-02 34H-115-01 34H-115-02 Plumbing and Heating Hydronic Heating Specialties 34B Series Scald Protection Mixing Valves 34B Series ASSE 1016 certified mixing valves are designed to be used for individual or multiple fixtures for flow as high as 11 GPM. These valves use a thermostatic element that senses outlet temperature and will compensate for fluctuating inlet temperature and pressure. The mixed water temperature range is 85°-120°F and will hold a desired temperature within +3° or -3°F at all times. The 34B also has an adjustable temperature limit stop to prevent the valve from being set above 120°F. • • • • • Low temperature range (85°-120°F) Stainless steel spring Bronze body Thermoplastic shuttle assembly Threaded or solder connections • • • • Size 1/2 1/2 3/4 3/4 1 1 1/2 1/2 3/4 3/4 1 1 Integrated checks Cold water failure protection Built in temperature limit stop Supply pressures to 125 psig Connection Sweat Thread Sweat Thread Sweat Thread Sweat/Check Thread/Check Sweat/Check Thread/Check Sweat/Check Thread/Check Low Temp. 85˚-120˚ 34B-103-01 34B-103-02 34B-104-01 34B-104-02 34B-105-01 34B-105-02 34B-113-01 34B-113-02 34B-114-01 34B-114-02 34B-115-01 34B-115-02 34C Series Commercial High Capacity Mixing Valves 34C Series ASSE 1017 listed, high-capacity mixing valves are thermostatically controlled regulating valves designed for use in large commercial potable and non-potable hot water systems. Simple adjustment of water temperature from 90°-140°F or 130°-180°F. • • • • Sizes: 3/4”, 1”, 1-1/4”, 1-1/2”, 2” Low temp range (90°-140°F) High temp range (130°-180°F) Threaded connections Size(in.) 3/4 1 1-1/4 1-1/2 2 • • • • Installs easily on heating source Patented design for easy in-line maintenance Supply pressures to 150 psig U. S. Patent No. 6,328,219 Low Temp.* 90˚-140˚ F 34C-104-01 34C-105-01 34C-106-01 34C-107-01 34C-108-01 High Temp. 130˚-180˚ F 34C-104-H1 34C-105-H1 34C-106-H1 34C-107-H1 34C-108-H1 *ASSE 1017 Certified Customer Service 1-704-841-6000 11 Plumbing and Heating Hydronic Heating Specialties 34D Series “Point of Use” Mini-Mixer 34D Series ASSE 1016 certified, “point of use” mixing valves are designed to sense and maintain preset outlet temperature compensating for fluctuations in hot and cold water temperatures and pressures. The mixed water temperature range is 85˚F to 120˚F and will hold a desired temperature within a ±3˚F at all times. The 34D also has an adjustable temperature limit stop to prevent the valve from being set above 120˚F. • • • • Corrosion Resistant Compression and FIP connections Easy maintenance Consistent outlet temperature with changing inlet conditions • Elevated temperature thermal element protection Single Outlet No. 34D-111-01 34D-111-08 34D-112-01 34D-112-08 34D-122-01 34D-122-08 • • • • • • ASSE 1016 approved Nickel plate option Saves energy by extending hot water supply Tamper resistant Scald protection Integrated check valves Size(in.) Inlet x Outlet 3/8 COMP. x 3/8 COMP. 3/8 COMP. x 3/8 COMP. 3/8 COMP. x 1/2 FIP 3/8 COMP. x 1/2 FIP 1/2 FIP x 1/2 FIP 1/2 FIP x 1/2 FIP Finish Bronze Chrome Plated Bronze Chrome Plated Bronze Chrome Plated 34D Double Outlet “Point Of Use” Mini Mixer 35FC Series All Bronze Hydronic Flow Check Valve The flow check shall be designed to provide positive shut-off when water service is interrupted. • • • • • Corrosion Resistant Wear Resistant Metal to Metal Seat Replaceable Seat Assembly By-Pass Option Sweat or Thread Connection Available No. 35-FC4-01 35-FC5-01 35-FC6-01 35-FC7-01 35-FC8-01 35-FC4-02 35-FC5-02 35FV Series • Designed For Easy Maintenance • Suitable For Hot or Cold Water Service • Maximum Working Pressure 50 psig. For 3/4" 1-1/4" 125 psig For 1-1/2" - 2" • Maximum Operating Temperature 250˚F Size(in.) 3/4 1 1-1/4 1-1/2 2 3/4 1 Connection NPT NPT NPT NPT NPT Sweat Sweat Wt./100 (lbs) 233 261 502 867 1220 112 155 Automatic Air Vent The 35FV Series provides automatic air venting of hot or cold water in distribution systems. The connections conform to ANSI B1.20.1: maximum working temperature of 230°F. A • Sizes 1/8" (35FV001) and 1/4"(35FV101) • Corrosion resistant • Variety of pipe end connections • Designed for easy maintenance • Purges air from hydronic systems • Suitable for use with glycol systems B No. 35FV001 35FV101 A(in.) 1.50 1.85 B(in.) 3.00 3.20 C(in.) 1/8 NPT 1/4 NPT C Ball Valve with Automatic Air Vent The 35FV001 can be installed with an Apollo ball valve in a typical hydronic distribution system. To order specify P/N# 78300FV. 78-300-FV 12 Customer Service 1-704-841-6000 Plumbing and Heating Hydronic Heating Specialties 57 Series Globe Valves Globe valves offer a 200 psig rating and aluminum wheel handle. No. 57-001-01 57-002-01 58 Series Size(in.) 1/4 NPT x 1/4 NPT 3/8 NPT x 3/8 NPT Wt./100 (lbs) 28.0 37.1 Balancing Valves Provide dependable hydronic control; for use with 1/2" and 3/4" copper water piping. Pressure rated to 150 psig. No. 58-003-01 58-004-01 78-668 Series Size 1/2 Solder 3/4 Solder Cv 4 14 Wt./100 (lbs) 30.0 53.4 Bronze Purge, Balance & Shut-off Valve Straight-through flow; all brass cover and chain prevent accidental system drainage. Hose thread connection for disposal of drained media No. 78-668-01 78-668-02 78-671-01* Size 3/4" 1" 3/4" Wt./100 (lbs) 206 359 198 *Available with screwdriver slotted stainless steel stem. Customer Service 1-704-841-6000 13 Plumbing and Heating Pressure Reducing Valves 36 Series Water Pressure Reducing Valves Controls high water pressure and problem fluctuations. Reduces supply pressures up to 300 psig to more functional range. Factory set at 50 psig; adjusts with turn of a bolt. • No cage screws • Meets ASSE and CSA standards; listed with IAPMO • Built-in by-pass, high-capacity strainer • Replaceable cartridge • Comes standard with union pipe end • Corrosion resistant • Available in sizes from 1/2" to 2" Specify pressure by using the following two digit key number following product number: -01 Standard (25 to 75 psig) -G1 Standard with 1/4" NPT gauge tapping -P1 Standard with 1/4” NPT gauge tapping and gauge (W-7793-00) in box -02 Low Pressure Range (10 to 35 psig) -G2 Low Pressure with 1/4" NPT gauge tapping -P2 Low Pressure with 1/4” NPT gauge tapping and gauge (W-7793-00) in box -03 High Pressure Range (75 to 125 psig) -G3 High Pressure with 1/4" NPT gauge tapping -P3 High Pressure with 1/4" NPT gauge tapping and gauge (W-7793-00) in box Jump Kits 36-100 & 36-300 Series Pipe Thread Soldier Joint Union x FNPT Union x FNPT 36-103 36-303 36-104 36-304 36-105 36-305 36-106 36-306 36-107 36-307 36-108 36-308 36-200 Series 36-203 36-204 36-205 36-206 36-207 36-208 36-400 & 36-500 Series Double Union Double Union NPT x NPT Solder x Solder 36-403 36-503 36-404 36-504 36-405 36-505 36-406 36-506 36-407 36-507 36-408 36-508 36-800 Series 36-806 36-900 & 36-9C4 Series 36-904 36-9C4 • • • • • • • • 36-100 Series pipe thread union inlet x FNPT outlet 36-200 Series FNPT inlet x FNPT outlet 36-300 Series solder-joint union inlet x FNPT outlet 36-400 Series pipe thread union inlet x union outlet 36-500 Series solder-joint union x union outlet 36-800 Series less unions 36-900 Series double union pex x pex 36-9C4 Series double union NPT x pex Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 A(in.) 6-1/8 6-1/8 6-1/2 8-5/8 8-5/8 11-3/4 B(in.) 4-5/8 4-5/8 5-1/8 6-3/8 6-5/8 8-7/16 C(in.) 1 1 1-1/8 1-3/8 1-3/8 1-13/16 Wt./100 (lbs) 350 340 450 1020 1045 2250 1/2 3/4 1 1-1/4 1-1/2 2 6-1/8 6-1/8 6-1/2 8-5/8 8-5/8 11-3/4 3-11/16 3-11/16 4-1/16 5-3/16 5-5/16 7-1/8 1 1 1-1/8 1-3/8 1-3/8 1-13/16 311 305 415 910 909 1880 Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 A(in.) 6-1/8 6-1/8 6-1/2 8-5/8 8-5/8 11-3/4 B(in.) 5-13/16 5-13/16 6-1/2 7-11/16 8 10-1/16 C(in.) 1 1 1-1/8 1-3/8 1-3/8 1-13/16 Wt./100 (lbs) 389 372 495 1090 1183 2472 1-1/4 8-5/8 5-13/16 1-3/8 910 3/4 3/4 6-1/8 6-1/8 5-13/16 5-13/16 1 1 372 372 36 Series Same rough end dimensions as a PRV but used as a spacer to flush system. No. 36-406-JK 36-506-JK 14 Customer Service 1-704-841-6000 Size(in.) 1-1/4 1-1/4 Description for 36-406 Series (threaded) for 36-506 Series (solder) Plumbing and Heating Pressure Reducing Valves 36C Series Compact Corrosion Resistant Pressure Reducing Valves Handles supply pressures up to 400 psig; working temperatures to 180°F. All-bronze body, corrosion resistant cage, stainless steel strainer and seat. Meets ASSE and CSA standards; listed with IAPMO. • • • • • • 6" 36C-U2P: Double union/pex inlet x pex outlet 36C-EMT: 90˚ meter thread union inlet x NPT outlet 36C-LU: Less unions 36C: NPT threaded inlet x NPT outlet 36C-U: NPT threaded union inlet x NPT outlet 36C-US: Sweat union inlet x NPT outlet • 36C-U2T: Double union/threaded inlet x threaded outlet • 36C-U2S: Double union/sweat inlet x sweat outlet • 36C-UM: Meter thread union inlet x NPT outlet • 36C-U2P: Pex union x pex union A Length OPTIONS TO ABOVE Gauge tapping SUFFIX -GT Gauge tapping & gauge #W-7793-00 (0-160 psig) in the box -GG Stainless Steel adjusting screw & nut, and sealed cage -SS LP range (low pressure) 10-35 psig -LP HP range (high pressure) 75-125 psig -HP Jump Kits Model No. Part No. Size(in.) NPT Threaded Inlet x Outlet 1/2" 36C 36C-203 1/2 3/4" 36C 36C-204 3/4 1" 36C 36C-205-01 1 NPT Threaded Union Inlet x NPT Outlet 1/2" 36C-U 36C-103 1/2 3/4" 36C-U 36C-104 3/4 36C-105 1 1" 36C-U Sweat Union Inlet x NPT Outlet 1/2" 36C-US 36C-303 1/2 36C-304 3/4 3/4" 36C-US 1" 36C-US 36C-305 1 Double Union/Threaded Inlet x Threaded Inlet 1/2" 36C-U2T 36C-403 1/2 3/4" 36C-U2T 36C-404 3/4 36C-405 1 1" 36C-U2T Double Union/Sweat Inlet x Sweat Outlet 1/2" 36C-U2S 36C-503 1/2 3/4" 36C-U2S 36C-504 3/4 1" 36C-U2S 36C-505 1 Meter Thread Union Inlet x NPT Outlet 1/2" 36C-UM 36C-603 1/2 36C-604 3/4 3/4" 36C-UM 1" 36C-UM 36C-605 1 90˚ Meter Thread Union Inlet x NPT Outlet 3/4" 36C-EMT 36C-704 1 x 3/4 1" 36C-EMT 36C-705 1x1 Less Unions 3/4'' 36C-LU 36C-804 3/4 36C-805 1 1" 36C-LU Double Union/Pex Inlet x Pex Outlet 1/2" 36C-U2P 36C-903 1/2 36C-904 3/4 3/4" 36C-U2P Length (in.) A(in.) Wt./100 (lbs) 3-1/2 3-1/2 3-3/4 1-5/8 1-5/8 1-1/2 200 200 225 4-13/32 4-13/32 4-3/4 1-5/8 1-5/8 1-1/2 240 240 270 4-13/32 4-3/4 4-13/32 1-5/8 1-5/8 1-1/2 240 240 270 5-3/8 5-3/8 5-7/8 1-5/8 1-5/8 1-1/2 280 280 310 5-3/8 5-3/8 5-7/8 1-5/8 1-5/8 1-1/2 280 280 310 4-13/32 4-13/32 4-3/4 1-5/8 1-5/8 1-1/2 240 240 270 9-5/8 13-7/16 1-5/8 1-1/2 400 580 3-1/2 3-3/4 1-5/8 1-1/2 211 218 5-3/8 5-3/8 1-5/8 1-5/8 280 280 36C Series Same rough end dimensions as a PRV but used as a spacer to flush system. No. 36C-404-JK 36C-504-JK 36C-405-JK 36C-505-JK Customer Service 1-704-841-6000 Size(in.) 3/4 3/4 1 1 Description for 36C-404 (threaded) for 36C-504 (solder) for 36C-405 (threaded) for 36C-505 (solder) 15 Plumbing and Heating Pressure Reducing Valves 36A Series Pressure Reducing Valves Handles supply pressures up to 400 psig; working temperatures to 180°F. All-bronze body, corrosion resistant cage, stainless steel strainer and seat. Meets ASSE and CSA standards; listed with IAPMO. No. 36A-103 36A-104 36A-105 36A-203 36A-204 36A-205 36A-303 36A-304 36A-305 36A-403 36A-404 36A-405 36A-503 36A-504 36A-505 A C B 36H Series Size(in.) 1/2 3/4 1 1/2 3/4 1 1/2 3/4 1 1/2 3/4 1 1/2 3/4 1 A(in.) 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 6-1/8 B(in.) 4-3/16 4-7/16 4-13/16 3-1/2 3-1/2 3-3/4 4-7/16 4-7/16 4-13/16 5-3/8 5-3/8 5-7/8 5-3/8 5-3/8 5-7/8 C(in.) 1-11/16 1-11/16 1-5/8 1-11/16 1-11/16 1-5/6 1-11/16 1-11/16 1-5/8 1-11/16 1-11/16 1-5/8 1-11/16 1-11/16 1-5/8 Wt./100 (lbs) 200 200 225 240 240 270 240 240 280 280 280 310 240 240 280 Super Capacity All Bronze Pressure Reducing Valves Super capacity all-bronze water pressure reducing valve with optional rugged Y strainer for commercial and light industrial applications. Controls supply pressures up to 400 psig. Ordering Number 36H - XXX - XX • Designed to meet ASSE and CSA standards; listed with IAPMO • Large yoke-type design aids flow and reduces resistance • Initial pressure up to 400 psig • Maximum temperature 180°F • Integral by-pass relief protects against thermal expansion W-8078-00 Series Options 0 - Standard 1- w/y strainer Connection 2 - FNPT 7 - flanged (2”-3" only) • Bronze body and cage, stainless steel replaceable seat • Sizes: 1/2", 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2" & 3" NPT - threads (inlet and outlet): 2", 2-1/2" and 3" offered in 150 lb. flange • Bottom access for easy in-line repair • Sealed case • Stainless steel bolts, adjustment screws and spring Size 3 - 1/2" 4 - 3/4" 5 - 1" 6 - 1-1/4" 7 - 1-1/2'' 8 - 2'' 9 - 2-1/2" 0 - 3'' Pressure Range 01-Std. Press Range (25 - 75 psig) 02-Low Press. Range (10 - 35 psig) 03-High Press. Range (75 - 125 psig) 3/4” Hose Thread Pressure Gauges • Hose connection pressure gauge with high pressure memory indicator used for testing water pressure. • Temp. range: 50°F to 130°F. No. W-8078-00 16 Customer Service 1-704-841-6000 Pressure Range 0-300 psig Wt./100 (lbs) 46.0 Plumbing and Heating Vacuum Breakers 38-100 Series Atmospheric Type Vacuum Breakers Economical protection against backsiphonage and low hazard cross connections. For hot and cold water service up to 212°F at 125 psig for 1/4" - 1"; and up to 180°F at 125 psig for 1-1/4" - 2". • Compact and lightweight • Heat resistant silicone seat disc • Easy to maintain and corrosion resistant No. 38-105 38-106 38-107 38-108 • Meets ASSE & CSA standards; listed with IAPMO • Finishes: Rough brass (-01); polished brass *(-04), rough chrome *(-03), or polished chrome *(-06) NPT Size(in.) 1 1-1/4 1-1/2 2 Wt./100 (lbs) 174.0 316.0 289.0 369.0 *38-105 only 38-200 Series Atmospheric Type Vacuum Breakers (Forged Body) Economical protection against backsiphonage and low hazard cross connections. For hot and cold water service up to 212°F at 125 psig for 1/4" - 3/4". • • • • Compact and lightweight Heat resistant silicone seat disc Easy to maintain and corrosion resistant Meets ASSE & CSA standards; listed with IAPMO No. 38-201 38-202 38-203 38-204 38-200 38-300 Series • Finishes: Rough brass (-01); rough chrome *(-03), or polished chrome *(-06) • Add HT to end of part number for high temperature (212˚F) NPT Size(in.) 1/4 3/8 1/2 3/4 Wt./100 (lbs) 51 47 55 80 3/4" Hose Connection Vacuum Breakers The Conbraco Series 38-304 and 38P Hose Connection Vacuum Breakers are designed to prevent cross connection caused by backsiphonage. They consist of a single check with an atmospheric vacuum breaker vent. They feature a break-away set-screw for tamper-proof protection. They are not suitable for continuous pressure applications. • Meets ASSE & CSA standards; listed with IAPMO • Maximum working pressure 125 psig No. 38-304-AS* 38-304-CS* 38-304-02 (Field Testable) 38P • Maximum temperature 180° F Finish Satin Brass Satin Chrome Satin Brass High Density Thermoplastic Wt./100 (lbs) 6.8 6.8 16.8 7.0 Note: 38P shipped in 25 pcs/bag. *Shipped in 12 pcs/box 38-304-02 38P Customer Service 1-704-841-6000 17 Plumbing and Heating Vacuum Breakers 38-400 Series 3/4" Anti-Freeze Hose Connection Vacuum Breakers The Conbraco Series 38-404 anti-freeze hose connection vacuum breaker is especially designed to prevent backsiphonage on wall and yard hydrants. It features a break-away set-screw for tamper-proof protection and manual drain for protection against freezing conditions. It is not suitable for continuous pressure applications. • Meets ASSE & CSA standards; IAPMO listed • Maximum working pressure 125 psig No. 38-404-01 38-404-03 38-502 Series • Maximum temperature 180°F Wt./100 (lbs) 37 37 Finish Satin Brass Satin Chrome Laboratory Faucet Vacuum Breakers Backflow protection for potable water using two independently acting soft-seated checks. Reversible inlet/outlet adapters make installation easy on lab faucets, community sinks, beauty salons and barber shops. • ASSE, CSA approved; IAPMO listed • 3/8" FNPT standard; 1/4" optional • Stainless steel internal components • Brass body, polished chrome plating A No. 38-502-01 38-502-02 38-502-03 38-502-CP2 38-502-CP3 Inlet 3/8" MNPSM 3/8" FNPT 3/8'' FNPT 1/4" FNPT 3/8" FNPT Outlet 3/8" FNPT 3/8" FNPT 3/8'' MNPSM 1/4" FNPT 3/8" FNPT A(in.) 2.33 2.34 2.33 2.34 2.34 B(in.) 1.24 1.24 1.24 1.24 1.24 B Backflow Preventers 4C-100 Series Carbonated Beverage Backflow Preventer Available with 1/4” and 3/8” flare end connections, Conbraco 4C-100 Carbonated Beverage Backflow Preventers (CBBPs) offer permanent protection against copper poisoning in carbonated beverage dispensing lines. Approved to ASSE 1022, they feature two independently acting check valves and an integral strainer at the inlet. They install permanently on the water supply line. In case of backflow, a diaphragm seat on the first check lifts and directs flow through an atmospheric port between the two check valves. • Temperature range: 33˚F to 130˚F • Maximum supply pressures to 150 psig • Special acetyl body and end caps • PVC/Stainless steel 100 mesh strainer • All wetted areas are non-toxic and corrosion resistant No. 4C-101-01 4C-102-01 18 Customer Service 1-704-841-6000 Size 1/4'' 3/8'' Plumbing and Heating Backflow Preventers DC Series Double Check Valve Assemblies Top entry assemblies dramatically reduce lay length, weight and head loss compared to same size conventional models. Standards: ASSE 1015, AWWA C-510, CSA B64.5, UL Classified, FM Approved and listed with IAPMO; USC for 2-1/2" to 6" sizes. Ordering Number 4S-1XX-OXU • Body/cover: FDA approved epoxy coated ductile iron • Perfect for fire protection sprinklers and irrigation systems • Diameters from 2-1/2" to 10" • Maximum working pressure 175 psig 40-100 Series • Temperature rated 33˚F to 140˚F • Modular design makes repairs simple • Easy in-line maintenance w/Elbows 0-Standard 1-w/Y-strainer (shipped Loose) Sizes 9 - 2-1/2" 0 - 3" A - 4" C - 6" E - 8" G - 10" 1-less gate valves 2-w/NRS gate valves 3-w/OS&Y gate valves 5-w/Epoxy coated ball valves (2-1/2" - 6") 6-w/OS&Y gate valve on inlet, NRS gate valve w/post plate and nut on outlet Double Check Valve Assemblies Bronze body (1/2" to 2") and epoxy-coated ductile iron body (2-1/2" to 10"). Replaceable seats and discs for easy maintenance. • Approved under ASSE, AWWA, CSA, FM (2-1/2" to 10"), USC’s FCCC&HR, UL classified (3/4" to 10") and listed with IAPMO • Temperature Range: 33°F to 180°F for 1/2'' to 2'', 33°F to 140°F for 2-1/2" to 10" • Working pressures up to 175 psig • Economical, durable, easy to install, maintain and repair • Low head loss • Corrosion resistant No. 40-103 40-104 40-105 40-106 40-107 40-108 Double Check Valve Assembly Sizes 3/4" to 2" (1/2" uses 0 instead of “A”) Suffix Description -A1 less ball valves -A2 with ball valves -A4 with union end ball valves Top Entry Double Check Valve Assembly – Sizes 3/4" to 2" Suffix Description -A1T less ball valves -A2T with ball valves -FP2 for UL classified service – Sizes 3/4" to 2" Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 No. 40-109 40-100 40-10A 40-10C 40-10E 40-10G Size(in.) 2-1/2 3 4 6 8 10 Top Entry 99T Double Check Valve Assembly Suffix Description -99T with ball valves and test cocks accessible on top -TC2 with SAE threaded test cock (3/4'' & 1'')* Double Check Valve Assembly Sizes 2-1/2'' to 10'' Suffix Description -01 less gate valves -02 with NRS gate valves -03 with OS&Y gate valves -05 with flanged ball valves (2-1/2'' to 6'')* -06 with OS & Y gate valves on inlet, NRS gate valves with post plate and nut on outlet (4'' to 10'') * Contact factory for latest approval status. Customer Service 1-704-841-6000 19 Plumbing and Heating Backflow Preventers 40-200 Series Reduced Pressure Principle Valves Protects against backpressure and backsiphonage. Sizes from 1/4" to 10". Features low head loss; Apollo® ball valves standard up to 2". • Approved under ASSE, AWWA, CSA, FM (2-1/2" to 10"), USC’s FCCC&HR, UL classified (3/4" to 2" & 3" to 10") and listed with IAPMO • Internal sensing passage • • • • Economical and corrosion resistant In-line servicing Easy to install, maintain and repair Low head loss Sizes 1/4” to 2” No. 40-201 40-202 40-203 40-204 40-205 40-206 40-207 Size(in.) 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 No. 40-208 40-209 40-200 40-20A 40-20C 40-20E 40-20G Size(in.) 2 2-1/2 3 4 6 8 10 Sizes 2-1/2” to 10” Reduced Pressure Pinciple Valves – Sizes 1/4" to 2" Suffix Description -A1 less ball valves -A2 with ball valves -A4 with union end ball valves -TC2 with SAE threaded test cocks (3/4'' and 1'' only) -99T with ball valves and test cocks accessible on top* Sizes 3/4" to 2" -A2U Inlet flow up, outlet flow down -A2Z Inlet flow up, outlet flow up Stainless Steel Reduced Pressure Backflow Preventer – Sizes 1/4" to 1" Suffix Description -A1S less ball valves -A2S with ball valves Reduced Pressure Principle Valves – Sizes 2-1/2'' to 10'' Suffix Description -01 less gate valves -02 with NRS gate valves -03 with OS&Y gate valves -05 with flanged ball valves (2-1/2" to 6 ") -99T* with ball valves and test cocks accessible on top *Note: Applicable to 1/4” to 2” sizes only. * Contact factory for latest approval status. Air Gap Drain Funnels minor relief valve discharges on 40-200 Series (RPZ) AGD Model No. 40-200-XA 40-200-X1 40-200-X1 40-200-X2 40-200-X2 40-200-X2 40-200-X3 40-200-X3 20 R.P. Size(in.) 1/4, 3/8, 1/2 3/4 - 1 1-1/4 - 2 2-1/2 - 3 4 6 8 10 Customer Service 1-704-841-6000 A(in.) 8-7/16 9-1/2 11-1/4 19 20 21 22-11/16 25-11/16 B(in.) 5 5-1/8 5-1/8 9-7/8 9-7/8 9-7/8 12-11/16 12-11/16 C(in.) 1 NPT 1 NPT 1 NPT 2 NPT 2 NPT 2 NPT 3 NPT 3 NPT Wt./100 (lbs) 230 340 340 1100 1100 1100 1245 1245 Plumbing and Heating Backflow Preventers 4P-300 Series 100% Lead Free In Line Dual Check Valve Series 4P-300 is designed to prevent cross connection of non-potable water (low hazard) into the potable drinking water systems. It is a compact and economical device. It consists of two independently acting, spring-loaded check valves in a lead-free high density thermoplastic body. It is suitable for supply pressure up to 175 psig; water temperature from 33° to 180°F. • Approved under ASSE & CSA • Tested and certified to ANSI/NSF-61 • Double union joint for ease of installation and removal for testing or repair • Low head loss Ordering Number 4P-3XX-XXA Angle Independently acting check valves Corrosion resistant Replaceable seats Various inlet and outlet connection combinations to fit your needs Outlet Connection A- FNPT E- Male Meter thread Inlet & Outlet Connection 3- 1/2" 4- 3/4" 5- 1" Inlet Connection A- FNPT C- Female meter thread S- Female meter thread (swivel) Dual Check Valve Prevents cross connections of non-potable, low hazard water into the potable drinking water system. In-line testable and maintainable. Compact and lightweight. • • • • • Approved under ASSE & CSA Sizes: 1/2", 3/4", 1" Working pressure to 175 psig Many inlet/outlet connection combinations available Corrosion resistant • Independently acting check valves • Easy to install, maintain and repair • Operating temperature 33°F to 180°F Blank - Standard 1- With Test Cocks 2 - With Test Cocks & Ball Valves 3- With Test Cocks & Outlet Ball Valve 4- With 4 Test Cocks & Outlet Ball Valves Ordering Number 40-3XX-XXX 40-300 Series • • • • Inlet Connection A- FNPT B- MNPT C- Female Meter Thread E- Male Meter Thread S- Female Meter Thread (Swivel) 2- Female BSPP Customer Service 1-704-841-6000 Outlet Connection A- FNPT B- MNPT C- Female Meter Thread E- Male Meter Thread F- Female BSPP Inlet & Outlet Size 3- 1/2" 4- 3/4" 5- 1" 21 Plumbing and Heating Backflow Preventers 40-400 Series Continuous Pressure Backflow Preventer Protects residential and commercial water supply lines from backsiphonage or back-pressure of non-potable substances. Suitable for hot or cold water service. Low head loss. Approved under ASSE & CSA Maximum working pressure: 175 psig Independently acting check valves Sizes 1/2" and 3/4" Corrosion resistant • • • • 4J-400 Series Economical Durable Easy to install, maintain and repair Operating temperature: 33˚F to 210˚F Outlet Connection A- FNPT B- MNPT F- Female BSPP H- Solder Joint Ordering Number 4O-4XX-XXM • • • • • Inlet & Outlet Size 3- 1/2" 4- 3/4" Inlet Connection A- FNPT H- Solder Joint 2- Female BSPP Continuous Pressure Backflow Preventer-Compact Design Protects from back-siphonage and back-pressure. Suitable for pressure up to 175 psig and water temperature from 33˚ to 210˚F. Corrosion resistant Independently acting check valves Ease of repair and installation Maximum working pressure 175 psig 40-500 Series • Operating temperature 175 psig • ASSE 1012 and CSA B64.3 approved • Sizes 1/2" and 3/4" Outlet Connection A- FNPT B- MNPT F- Female BSPP H- Solder Joint Ordering Number 4J-4XX-XX • • • • Inlet Connection A- FNPT H- Solder Joint 2- Female BSPP Inlet & Outlet Size 3- 1/2" 4- 3/4" Pressure Type Vacuum Breaker Designed for use in continuous pressure potable water systems. Includes spring-loaded float disc and independent check valve. Sizes from 1/2" to 2" Approved under ASSE, CSA & USC’s FCCC&HR Working pressure to 150 psig Apollo ball valves standard Ordering Number 4O-50X-0X • • • • 22 Customer Service 1-704-841-6000 • Easy to install, maintain and repair • Corrosion resistant, economical and durable • Operating temperature 33˚F to 210˚F 1- less ball valves 2- with ball valves 4- w/union end ball valves 3- 1/2" 4- 3/4" 5- 1" 6- 1-1/4” 7- 1-1/2” 8- 2” Plumbing and Heating Backflow Preventers 4V-500 Series Freeze Resistant Vacuum Breakers Protects and enhances the performance of irrigation systems in even the coldest conditions. Designed with plastic float and integral relief valve that vents automatically. Bottom test cock assures easy draining. • Temperature range 32˚F to 180˚F • ASSE 1020 and CSA B64.1.2 approved • Replaceable check valve cartridge • Apollo® ball valves standard • 150 psig maximum working pressure Ordering Number 4 V - 50 X - 0 X 1- less ball valves 2- with ball valves 4- w/union end ball valves 4W-500 Series 3- 1/2" 4- 3/4" 5- 1" Spill Resistant Vacuum Breakers The spill-resistant pressure vacuum breaker (SVB) is designed to prevent contamination of potable water due to backsiphonage and ideally suited for indoor and OEM applications supplied with continuous pressure. • • • • • Corrosion resistant In-line flow Integral shut-off valves Designed for easy maintenance Low head loss • • • • Economical Maximum working pressure 150 PSIG Operating temperature range 33˚F-180˚F Approved under ASSE 1056. No. 4W-501-02 4W-502-02 4W-503-02 Double Check Detector Assembly Double check protection against low hazard cross-connection conditions. Detects leakage or unauthorized use of water from fire or sprinkler systems. • Approved under ASSE 1048, FM & USC’s FCCC&HR, UL Classified • Sizes: 3" to 10" • Test cocks for in-line testing Ordering Number 4 O - 60 X - X X 40-600 Series Size 1/4'' 3/8'' 1/2'' Customer Service 1-704-841-6000 • Removable bronze seats (mainline) • Working pressure 175 psig • Operating temperatures 33˚F to 140˚F 1- less gate valves 3- with OS&Y gate valves 6- with OS&Y gate valves on inlet, NRS gate valves with post plate and nut on outlet (4''' to 10'') 0- 3" A- 4" C- 6" C- with meter in cubic feet E- with meter in gallons G- less water meter E- 8" G- 10" 23 Plumbing and Heating Backflow Preventers 40-700 Series Reduced Pressure Detector Assembly Protection against hazardous cross-connection. Detects leakage or unauthorized use of water from fire or sprinkler systems. • Approved under ASSE 1047, FM, UL Classified, USC’s FCCC&HR • Internal sensing passage • Sizes: 3" to 10" • Removable bronze seats (mainline) • Working pressure 175 psig • Operating temperatures 33˚F to 140˚F Ordering Number 4 O - 70 X - X X 1- less gate valves 3- with OS&Y gate valves C- with meter in cubic feet E- with meter in gallons G- less water meter 0- 3" A- 4" C- 6" E- 8" G- 10" In-Line Check Valves 61-100, 61-200 & 62-100 Series Ball-Cone® Check Valves Patented design (U.S. Pat. No. 4,172,465) with reinforced ball-cone check and stainless steel springs, these valves offer exceptional resistance to chemicals and corrosion. No radial alignment is needed. • 1/2” psi opening pressure • Bronze sizes from 1/4" to 3"; stainless steel sizes 1/4" to 2" • Tight shut-off with liquid media Bronze FNPT x FNPT 61-101 61-102 61-103 61-104 61-105 61-106 61-107 61-108 61-109 61-100 Bronze MNPT x FNPT 61-201 61-202 61-203 61-204 61-205 61-206 61-207 61-208 – – SS Ball Cone FNPT x FNPT 62-101 62-102 62-103 62-104 62-105 62-106 62-107 62-108 – – Options Available On Request Suffix - 5 psig opening pressure -E05 - 10 psig opening pressure -E10 - Light spring (for light spring replace 0 in fourth digit with 2) - Oxygen clean -57 - Nitrile seat -31 (soft seat checks only) 24 Customer Service 1-704-841-6000 Size(in.) 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 • • • • 125 psig steam rating Straight-through design minimizes flow changes See PRECAUTIONARY NOTE See OPTIONS below A(in.) 2-1/16 2-1/8 2-5/16 2-7/8 3-1/2 4-3/16 4-15/16 6 7 8-1/8 B(in.) C(in.) 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-1/8 1-3/8 1-1/2 1-3/4 1-15/16 2-1/8 2-3/8 2-1/2 2-13/16 3 3--11/16 3-1/2 4-1/2 4-1/8 5-5/16 61 Series Wt./100 38.0 38.0 38.0 75.0 145.0 275.0 394.0 630.0 1400.0 1665.0 62 Series Wt./100 38.3 37.3 36.3 76.6 145.0 237.5 381.3 636.0 – – Pressure Temperature Ratings Degrees (F) PSIG -20 to 100 400 200 200 250 160 275 150 300 140 325 130 353 125 Plumbing and Heating In-Line Check Valves 61-500 & 62-500 Series Soft Seat Check Valves Fabricated with stainless steel springs and elastomeric seats. No radial alignment is needed. Exceptional resistance to chemicals and corrosion. Spring is fully shielded from flow. • Bronze sizes: 1/4" to 2" • Stainless steel sizes: 1/4" to 1" • Bubble-tight shutoff, ideally suited for gaseous service • Straight-through design minimizes flow changes Bronze FNPT x FNPT 61-501 61-502 61-503 61-504 61-505 61-506 61-507 61-508 SS Ball Cone FNPT x FNPT 62-501 62-502 62-503 62-504 62-505 – – – Size(in.) 1/4 3/8 1 /2 3 /4 1 1-1/4 1-1/2 2 • NPT threaded; 400 psig WOG • Retainer is notched for easy identification • Check is spring loaded for fast seating action; approximate opening pressure 1/2 psi • See “PRECAUTIONARY NOTE” A(in.) 2 5/16 2 5/16 2 5/16 2 7/8 3 1/2 4-3/16 4-15/16 6 B(in.) 1-1/8 1-1/8 1-1/8 1-3/8 1-3/4 2-1/8 2-1/2 3 C(in.) 1-1/8 1-1/8 1-1/8 1-1/2 1-15/16 2-3/8 2--13/16 3-11/16 61 Series Wt./100 38 38 38 75 145 275 394 630 62 Series Wt./100 38 38 38 75 150 – – – Solder End Soft Seat Check Valves 61-600 Series All bronze with stainless steel springs and elastomeric seats. No radial alignment is needed. Exceptional resistance to corrosion. Spring fully shielded from flow. • Sizes: 1/2” to 2” • Bubble-tight shutoff, ideally suited for gaseous service • Straight-through design minimizes flow changes No. 61-603 61-604 61-605 61-606 61-607 61-608 C B A 61-700 Series Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 A(in.) 2.75 3.68 4.50 6.11 6.87 7.46 • Solder end; 400 psig WOG • Check is spring loaded for fast seating action; approximate opening pressure 1/2 psi • See “PRECAUTIONARY NOTE” • Retainer is notched for easy identification B(in.) 1.12 1.20 1.93 2.13 2.50 3.38 C(in.) 1.25 1.62 2.12 2.38 2.81 3.75 Wt./100 (lbs) 138 175 145 330 610 1010 Brass NPT “Mini” Check Valves Ideally suited for all OEM applications where space is a premium. Excellent for use on water and air. They feature a bubble-tight soft seat design with a very light loaded stainless steel spring. No. 61-701-01 61-702-01 61-703-01 61-704-01 61-705-01 A(in.) 1.72 1.79 2.02 2.50 2.95 B(in.) .81 .93 1.06 1.25 1.62 C(in.) .92 1.05 1.17 1.40 1.76 Wt./100 (lbs) 22 29 38 54 110 Precautionary Note Not recommended for use with reciprocating pumps and similar applications which may induce repetitious vibrations. Low flow rates which do not fully open the valve, may result in undesirable noise and premature valve failure. Upstream flow disturbances, which create turbulence, may also result in rapid wear. Therefore, it is recommended that a minimum of 10 diameters of straight pipe be provided between the check valve and any upstream flow disturbances such as pumps, control valves, elbows, etc. C B Size(in.) 1/4" 3/8" 1/2" 3/4" 1" A Customer Service 1-704-841-6000 25 Plumbing and Heating In-Line Check Valves 70-100-BC Series Unidirectional Ball Valve with Integral Check Rugged ball valve for all water systems not exceeding 250 psig. Combination positive shut-off valve with bubble-tight check capability; perfect where space savings is required. • Ideal for O.E.M. applications • FNPT threaded connections • Sizes 1/2" to 2" No. 70-103-BC 70-104-BC 70-105-BC 70-106-BC 70-107-BC 70-108-BC E • Lever handle standard • Rated 250 psig • Adjustable packing gland Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 A(in.) .42 .45 .59 .75 1.02 1.27 D Suffix -02 -03 -04 -07 -08 A B B(in.) 1.11 1.50 1.68 2.00 2.14 2.35 C(in.) 2.22 3.00 3.37 4.00 4.31 4.68 Option Static Grounded 1-1/4" Stem Extension 2-1/4" Stem Extension Tee Handle 90˚ Reversed Stem Wt. Ea. (lbs) .63 1.33 1.77 3.29 4.63 6.01 D(in.) 1.80 2.12 2.25 2.73 3.09 3.28 E(in.) 3.87 4.87 4.87 5.50 8.00 8.00 Suffix -10 -15 -17 -27 -32 -45 Option SS Lever and Nut Round Handle Rough Chrome Plating Latch Lock Lever SS Tee Handle and Nut Less Lever and Nut C Pipeline Strainers Bronze NPT “Y” Strainers 59 Series Lightweight, compact protection against foreign particles. Corrosion-resistant bronze body and stainless steel screens. Operating pressures to 400 psig. A • • • • Sizes: 1/8" to 4" Self-aligning screen makes cleaning easy Small sizes ideal for O.E.M. applications Rated 400 psig at 150°F WOG • Optional tapped caps available (less plug) • Optional mesh screens available upon request • Sizes 1/8" to 1/2" available as UL® recognized component (Made from 85-5-5-5 bronze) B A C B 59-00X-06 No. 59-000-01 59-001-01 59-002-01 59-003-01 59-004-01 59-005-01 59-006-01 59-007-01 59-008-01 59-009-01 59-010-01 59-011-01 59-003-06 59-004-06 59-005-06 59-006-06 59-007-06 59-008-06 Standard Screen Size 1/8 to 1/2 3/4 to 3 4 26 Size(in.) 1/8 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 1/2 3/4 1 1-1/4 1-1/2 2 A(in.) 2 2 2-11/16 2-11/16 3-7/8 4-3/4 5-1/8 5-3/4 6-3/4 7-15/16 9-1/8 11-15/16 2-11/16 3-13/16 4-3/4 5-1/8 5-3/4 6-25/32 Screen Opening 50 Mesh 20 Mesh .125 Perforation Customer Service 1-704-841-6000 B(in.) C(in.) 1-1/4 1-3/4 2 2 3-1/4 4 4-1/4 5 6 5-7/8 6-7/8 10-1/8 3-3/4 6-61/64 2-15/16 8-31/32 3-5/8 11 3-15/16 11-1/2 4-13/32 12-27/64 4-21/32 13-25/32 Screen Area(in.2) 1.38 1.38 3.19 3.19 8.18 12.9 16.2 22.8 32.7 47.3 64.8 115 3.19 8.18 12.9 16.2 22.8 32.7 Suffix -01 -02 -06 -P2 Tapped Cap/NPT Suffix (-02) 1/8 1/8 1/4 1/4 1/2 3/4 3/4 1 1-1/4 1-1/4 1-1/2 1-1/2 - Wt./100 (lbs) 44.5 42.5 78.6 75.1 185 276 358 541 747 1130 1580 3070 138 246 417 499 720 1091 Option Solid cap (standard) Tapped cap Tapped cap with Ball Valve Tapped cap with pipe plug (available in 1/2" thru 2") Plumbing and Heating Pipeline Strainers 59-300 Series Bronze Sweat End “Y” Strainers Designed with minimal wall thickness at solder ends to allow high strength joints. Lightweight and compact with corrosionresistant bronze bodies, stainless steel screens. A • Operating pressures to 400 psig • Sizes: 1/2" to 2" No. 59-303-01 59-304-01 59-305-01 59-306-01 59-307-01 59-308-01 B Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 Standard Screen Size 1/2 3/4 to 2 59V Series A • Optional tapped caps for easy screen cleaning (less plug) A(in.) 2-3/4 4 4-3/4 5-1/4 6 7-1/4 Screen Opening 50 Mesh 20 Mesh Screen Area(in.2) 3.19 8.18 12.9 16.2 22.8 32.7 B(in.) 1-13/16 2-7/8 3-9/16 3-15/16 4-5/8 5 Suffix -01 -02 -P2 Tapped Cap/NPT Suffix (-02) 1/4 1/2 3/4 3/4 1 1-1/4 Wt./100 (lbs) 50 121 189 280 426 627 Option Solid cap (standard) Tapped Cap Tapped cap with pipe plug Ideal for O.E.M. applications where space is a premium. Designed to be more compact than comparable size “Y” strainers. Corrosion-resistant bodies and cleanout cap with stainless steel screens. • Rated 400 psig at 210°F WOG and 125 psig at 400°F WSP • Sizes: 1/8" and 1/4" NPT • 50 mesh screen standard, optional 80 or 100 mesh B No. 59V-000-01 59V-001-01 TCG Series Size(in.) 1/8 1/4 A(in.) 1-3/4 2 B(in.) 1-1/4 1-5/16 Cv 1.03 1.42 Wt./100 (lbs) 25 29.7 Cast Iron Pipe Threaded Y-Strainer Used to protect meters, nozzles, pumps, condensers, heat exchangers and other process equipment from harmful debris. A B • Graphite gasketed blowoff plug for easy clean-out • 20 mesh screens standard to 2"; .045 perf 2-1/2" to 3", others available • Sizes: 1/4" to 3" No. 612-011-A1 612-012-A1 612-013-A1 612-014-A1 612-015-A1 612-016-A1 612-017-A1 612-018-A1 612-019-L1 612-010-L1 Customer Service 1-704-841-6000 Size(in.) 1/4 3/8 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 A(in.) 3-3/16 3-3/16 3-3/16 3-3/4 4 5 5-3/4 7 7-1/2 7-1/2 B(in.) 2-3/8 2-3/8 2-3/8 3-3/8 3-1/2 4-1/8 4-11/16 5-7/16 5-7/16 5-7/16 Blow-off NPT 1/4 1/4 1/4 3/8 1/2 3/4 3/4 1 1-1/4 1-1/4 Wt./100 (lbs) 1.25 1.25 1.50 2.25 3.00 5.25 6.50 11.13 23.50 33.00 27 Plumbing and Heating Pipeline Strainers FC1 & FC2 Series Cast Iron Pipe Flanged Y-Strainers Same great features as the Model TCG but with flanged connections. A • FC1 rated at 125 psig WOG • 2-1/2” - 6” available as UL recognized B 28 No. 613-217-L1 613-317-L1 613-218-L1 613-318-L1 613-219-L1 613-319-L1 613-210-L1 613-310-L1 613-21A-N1 613-31A-N1 613-21B-N1 613-31B-N1 613-21C-N1 613-31C-N1 613-21E-N1 613-31E-N1 613-21G-N1 613-31G-N1 613-21H-N1 613-31H-N1 613-21J-N1 613-31J-N1 613-21K-N1 613-31K-N1 613-21L-P1 613-31L-P1 Model FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 FC-1 FC-2 • FC2 rated at 250 psig WOG • Sizes 1-1/2" to 18" Size(in.) A Class 125 B Class 125 A Class 250 B Class 250 Blow-off NPT 1-1/2 9-1/2 5-7/16 9-1/2 5-7/16 3/4 2 9-1/2 6-1/2 11-5/8 6-1/8 1 2-1/2 10-1/2 7 13 6-3/4 1-1/4 3 12 8 14 8 1-1/4 4 14-7/8 10-3/4 17-1/16 10-3/4 1-1/4 5 17-3/8 13-1/2 19-1/16 13-1/2 1-1/2 6 21 16-1/4 21-1/16 16-1/4 1-1/2 8 22-1/2 17 23 19-1/2 2 10 26-1/8 20-1/4 28 21-1/4 2-1/2 12 30-3/8 24 32-5/8 25 2-1/2 14 36 29 37-5/8 29-1/2 2 16 37 33 38-15/16 33-1/2 2-1/2 18 46 35-1/2 47-5/8 36-1/2 3 Customer Service 1-704-841-6000 Plumbing and Heating Section IV ASME Hot Water Boiler Safety Relief Valves 10 Series Section IV ASME Hot Water Boiler Relief Valves These capacity-certified relief valves protect against excessive water pressure (from thermal expansion) and steam generated when Btu input controls fail. Valves comply with ASME Section IV requirements. Ideal for use with hot water boilers and heating systems. 10-102 • Pressures from 30 to 150 psig • Brass or bronze body available with satin or polished chrome finish • Maximum temperature service: 250°F • 10-321 in polished chrome only • Registered in all Canadian provinces and territories, CRN #0G2663.1C No. 10-102 10-104 10-214 10-301 10-303 10-321 10-407 10-408 10-417 10-418 10-104 Size(in.) Inlet Outlet NPT NPT 3/4 F 1F 3/4 M 1F 1F 1F 3/4 M 3/4 F 3/4 F 3/4 F 3/4 M 3/4 F 3/4 M 3/4 F 3/4 F 3/4 F 3/4 M 3/4 F 3/4 F 3/4 F Certified Pressure Range PSIG 20-60 20-60 20-65 20-60 20-60 20-60 30&50 30&50 20-60 20-60 Height (in.) 3-5/16 3-3/4 5 3-3/4 3-5/16 3-3/4 3 2-3/4 3 2-3/4 • Stainless steel springs standard except 10-214 • 10-624/634 are ideal for use in various plumbing systems, commercial boiler applications and swimming pool heaters • 10-418/417 are ideal for use in swimming pool heater applications Wt./100 (lbs) 105 109 227 114 115 123 62 65 62 65 30 PSIG 710,000 710,000 1,000,000 550,000 550,000 425,000 535,000 535,000 477,000 477,000 *Certified Capacity 40 50 75 PSIG PSIG PSIG 870,000 1,035,000 870,000 1,035,000 1,210,000 1,450,000 675,000 805,000 675,000 805,000 525,000 625,000 – – 577,000 697,000 1,027,000 577,000 697,000 1,027,000 *National Board Capacity Certified – Btu Per Hour (90% of actual capacity at 10% accumulation) ASME boiler and pressure vessel code – Section IV – Heating Boilers SUFFIX KEY Part No. Pressure PSIG 20 22 25 30 35 40 43 45 50 55 60 10-321 10-407 & 10-417 No. 10-624 10-634 Size(in.) Inlet Outlet NPT NPT 3/4 M 3/4 F 3/4 F 3/4 F Certified Pressure Range Height Wt./100 PSIG (in.) (lbs) 30-150 4-5/8 106 30-150 4-5/8 106 Plain Brass -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 -12 30 PSIG 689,000 689,000 Satin Chrome -41 -42 -43 -44 -45 -46 -47 -48 -49 -50 -51 Polished Chrome -67 -68 -69 -70 -71 -72 -73 -74 -75 -76 -77 *Certified Capacity 75 100 125 PSIG PSIG PSIG 1,405,000 1,802,000 2,199,000 1,405,000 1,802,000 2,199,000 150 PSIG 2,597,000 2,597,000 Note: to order add pressure setpoint to the end of base number. (i.e. 10624150=150PSIG) 10-634 Customer Service 1-704-841-6000 29 Plumbing and Heating Section IV ASME Hot Water Boiler Safety Relief Valves 10-600 Series Section IV ASME High Capcity Safety Relief Valves For Hot Water Boilers and Heating Systems High-capacity heating system valves with female inlet, expanded or standard female outlet. Elevated seat for drainage of water away from seat area. Entire pressure range is National Board capacity certified. B • • • • 3/4” to 2-1/2” connections High Btu capacity rating Silicone seat Fabric reinforced molded diaphragm isolates spring from water at all times • Bronze body and spring cage A D C Size(in.) Inlet Outlet NPT NPT 3/4F 3/4F 3/4F 1F 1F 1F 1F 1-1/4F 1-1/4F 1-1/4F 1-1/4F 1-1/2F 1-1/2F 1-1/2F 1-1/2F 2F 2F 2F 2F 2-1/2F No. 10-604 10-614 10-605 10-615 10-606 10-616 10-607 10-617 10-608 10-618 Certified Pressure Range PSIG 15-160 15-160 15-160 15-160 15-160 15-160 15-160 15-160 15-160 15-160 • Maximum temperature service 250°F • Registered in Canadian provinces and territories CRN #0G2663.1C • Protects against excessive water pressure due to failure of controls to regulate Btu input • Pressures from 15-160 psig Wt./100 (lbs) 232 226 410 390 795 755 1100 1145 2375 2315 A(in.) 1-1/16 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 2 2 2-3/16 2 3/16 B(in.) 5-1/4 5-1/4 6-11/16 6-11/16 6-3/8 8-3/8 10-3/4 10-3/4 14 14 C(in.) 1-5/8 1-23/32 2 2 2-7/18 2-15/32 2-3/4 2-3/4 3-11/16 3-21/32 D(in.) 1-9/16 1-9/16 2 2 2-5/8 2-5/8 3-1/8 3-1/8 3-1/2 3 -1/2 Use Suffix No. to designate last two digits of Product No. for desired pressure. Other pressure settings available upon request. 17 Series Pressure PSIG 30 50 75 100 125 150 Suffix No. -05 -10 -15 -20 -25 -34 10-600 Series Discharge Capacities BTU/Hour 3/4 x 3/4 1x1 1-1/4 x 1-1/4 10-604 10-605 10-606 827,000 1,339,000 2,316,000 1,209,000 1,956,000 3,384,000 1,686,000 2,728,000 4,720,000 2,162,000 3,500,000 6,055,000 2,639,000 4,272,000 7,390,000 3,116,000 5,044,000 8,725,000 1-1/2 x 1-1/2 10-607 3,151,000 4,604,000 6,421,000 8,238,000 10,054,000 11,871,000 2x2 10-608 5,193,000 7,589,000 10,583,000 13,577,000 16,571,000 19,565,000 Pressure PSIG 30 50 75 100 125 150 Suffix No. -05 -10 -15 -20 -25 -34 10-610 Series Discharge Capacities BTU/Hour 3/4 x 1 1 x 1-1/4 1-1/4 x 1-1/2 10-614 10-615 10-616 970,000 1,570,000 2,716,000 1,418,000 2,295,000 3,969,000 1,977,000 3,200,000 5,535,000 2,536,000 4,105,000 7,101,000 3,096,000 5,011,000 8,668,000 3,655,000 5,916,000 10,234,000 1-1/2 x 2 10-617 3,696,000 5,400,000 7,531,000 9,661,000 11,792,000 13,923,000 2 x 2-1/2 10-618 6,091,000 8,900,000 12,412,000 15,924,000 19,435,000 22,947,000 Pressure Only Relief Valve for Tankless Coils & Storage Tanks Prevents excessive thermal expansion buildup in plumbing systems, tank applications and tankless water heaters. Conforms to HUD/FHA requirements. Ideal for well systems. • Bronze body, stainless steel spring • CSA certified design to ANSI Z21.22 “Relief Valves for Hot Water Supply Systems.” No. 17-401 17-402 • ASME capacity certified from 75 to 150 psig. • CRN #0G2663.1C registered in all Canadian provinces and territories Size (in.) Wt./100 (lbs) 1/2 M x 1/2 F 3/4 M x 3/4 F .57 .53 *ASME Certified Discharge Capacities BTU/HR 75 100 125 150 505,000 648,000 791,000 934,000 Note: When ordering specify pressure by adding the two digit key number after the product number as follows: 75 psig - 01; 100 psig - 02; 125 psig - 03; 150 psig - 04; 160 psig - 05 * National Board Capacity Certified - BTU per hour (90% of actual capacity at 10% accumulation) ASME boiler and pressure vessel code - Section IV - Heating Boilers 30 Customer Service 1-704-841-6000 Plumbing and Heating Section IV ASME Hot Water Boiler Safety Relief Valves 18 Series Water Heater T&P Relief Valves Automatic temperature and pressure relief valves feature unique non-metallic coating which protects the element against galvanic and electromechanical corrosion by isolating it from the heated water. This coating is electrostatically applied for uniform coverage, then thermobonded, resulting in optimum adhesion for extended service life. CSA design certified at all settings to ANSI Z21.22. ASME Section IV rated at 125 psig and 150 psig settings for 3/4 NPT only. • Meets HUD/FHA requirements • Cast bronze body, stainless steel spring • Rated 210°F maximum No. 18-401 18-401 18-401 18-402 18-402 18-402 • CRN #0G2663.1C registered in all Canadian provinces and territories • ASME capacity certified to 450,000 BTU/HR. Size 1/2 M x 1/2 F 1/2 M x 1/2 F 1/2 M x 1/2 F 3/4 M x 3/4 F 3/4 M x 3/4 F 3/4 M x 3/4 F SUFFIX KEY Pressure PSIG 75 100 125 150 175 1" -04 -11 -27 -28 -38 Element Length 1 4 8 1 4 8 Wt./100 (lbs) 64.0 64.0 64.0 64.4 64.4 64.4 CSA Capacity rating BTU/HR 15,000 15,000 15,000 80,000 100,000 100,000 Coated Element Length 4" -05 -12 -29 -30 -24 8" -07 -14 -36 -37 -41 Section IV ASME Low Pressure Steam Safety Relief Valves Low Pressure Steam Heating Boiler Safety Valves 12-200 Series Use on medium and large commercial and industrial steam heating and processing boilers. National Board capacity certified at 15 psig; PTFE coated O-Ring seat seal. A • All bronze construction • 3/8" NPT side tapping for drain • Top guide, rust-proof steel spring B D C No. 12-205 12-206 12-208 Size(in.) Inlet Outlet NPT NPT 2 2 2-1/2 2-1/2 3 3 Max. Pressure PSIG 15 15 15 • High capacity • Registered in all Canadian provinces and territories, CRN #0G2663.1C Dimensions Capacity* Lbs./Hr 2500 3529 4100 Wt./100 (lbs) 514 835 1162 A(in.) 6 8-1/2 9-1/2 B(in.) 3-3/4 5-1/4 6 C(in.) 2-5/8 3-1/16 3-3/4 D(in.) 4 4 4 Note: When ordering specify pressure by adding the two digit key number after the product number as follows: 5 psig - 03; 6 psig 04; 8 psig - 05; 10 psig - 06; 12 psig - 07; 15 psig - 08 *National Board Capacity Certified-(90% of actual capacity at 33% accumulation.) Customer Service 1-704-841-6000 31 Plumbing and Heating Section IV ASME Low Pressure Steam Safety Relief Valves Low Pressure Steam Heating Boiler Safety Valves 13 Series National Board capacity-certified at 15 psig in accordance with ASME Section IV; rough or polished chrome finish; positive drainage of condensate from seat area. • Flat seat, PTFE faced disc for positive seal • Standard set pressure of 15 psig; capacities apply to valves set @ 15 psig • No. 13-101 is top outlet discharge • Registered in all Canadian provinces and territories, CRN #0G2663.1C A No. 13-101 13-211 13-202 13-213 13-214 13-511 13-512 C B Size(in.) Inlet Outlet NPT NPT 3/4 M Top 3/4 M 3/4 F 1M 1F 1-1/4 M 1-1/2 F 1-1/2 M 2F 3/4 M 3/4 F 3/4 F 3/4 F 13-101 Max. Pressure PSIG 15 15 15 15 15 15 15 Dimensions Capacity* Lbs./Hr 410 475 643 1200 1900 407 407 Wt./100 (lbs) 64 107 110 218 320 62 59 A(in.) 2-7/8 1-13/16 2-1/16 2-17/32 3 1-11/16 1-3/16 B(in.) 15/16 3-11/16 3-7/8 4-1/2 5-1/4 3-1/4 2-3/4 C(in.) 1-1/4 1-7/16 1-7/32 1-7/8 2-3/16 1-3/16 1-3/16 D(in.) – 1-13/32 1-13/32 1-1/2 1-13/16 1-1/4 1-1/4 *National Board Capacity Certified at 15 psig. (90% of actual capacity at 33% accumulation.) Use key to designate last two digits of model number. Last two digits indicate pressure and finish. B SUFFIX KEY A B C B 13-200 A Plain Brass -03 -04 -05 -06 -07 -08 Pressure PSIG 5 6 8 10 12 15 Satin Chrome -35 -36 -37 -38 -39 -40 Polished Chrome -43 -44 -45 -46 -47 -48 C D 13-511 High Capacity Low Pressure Steam Boiler Safety Valves 14-200 Series National Board capacity-certified in accordance with ASME Section IV at 15 psig. For commercial and industrial boilers. Capacities up to 6843 lbs./hr. • Nozzle-type chrome-plated brass disc • Test gag available to allow hydrostatic testing. (Add “G” suffix to pressure code when ordering.) • PTFE coated O-ring for positive seal B • One piece body, all bronze construction • Rust proof steel spring • Registered in all Canadian provinces and territories, CRN #0G2663.1C A D C No. 14-205 14-206 14-207 Size(in.) 2x2 2-1/2 x 2-1/2 3x3 *Capacity Lbs./Hr. 3150 4676 6843 Wt./Each (lbs) 8.4 13.0 17.0 A(in.) 3 3-1/2 4-1/8 Dimensions B(in.) C(in.) 7-1/8 3-1/8 8-1/4 3-1/2 9-3/8 3-7/8 *National Board Capacity Certified at 15 psig.(90% of actual capacity at 33% accumulation.) Note: When ordering specify pressure by adding the two digit key number after the product number as follows: 5 psig - 03; 6 psig - 04; 8 psig - 05; 10 psig - 06; 12 psig - 07; 15 psig - 08 32 Customer Service 1-704-841-6000 D(in.) 4 4 4 Plumbing and Heating Section VIII ASME Safety Valves 10-322 & 10-512 Series ASME Section VIII Steam Safety Relief Valves National Board capacity-certified safety relief valves; brass body with optional satin or polished chrome finish. Protects against excess pressure from thermal expansion and steam caused by failure of BTU input controls. Ideally suited for O.E.M. applications such as steam cookers, autoclaves, sterilizers, coffee makers and similar equipment. • Stainless steel springs • Discharge capacities to 725 lbs./hr. • Pressure settings 15 to 60 psig No. 10-322 10-512 10-512 Model 10-512 available with optional stainless steel trim. Use key to designate last two digits of model number. Last two digits indicate pressure and finish. Example: 10-322-67 = 20# pressure, polished chrome * ASME (UV) Rating – 90% of actual capacity at 10% accumulation. Capacity in lbs. of saturated steam per hour 10-322 15 Series • 10-322 in polished chrome only • CRN OG2663.1C, registered in all Canadian provinces and territories Size(in.) Inlet Outlet NPT NPT 3/4 M 3/4 F 1/2 M 1/2 F Key Pressure No. 15 20 25 30 35 40 45 50 55 60 Pressure Range PSIG 15-60 15-60 Plain Brass 01 02 04 05 06 07 09 10 11 12 Height 3-3/4 2-5/8 Wt./100 (lbs) 128 58 *Certified Capacities Satin Polished 10.322 10.512 Chrome Chrome Lbs./Hr. Lbs./Hr. J2 65 151 41 67 325 178 43 69 375 205 44 70 425 232 45 71 475 258 46 72 525 285 48 74 575 312 49 75 625 339 50 76 675 366 51 77 725 392 ASME Air Relief Valves • • • • National Board certified 15 psig through 250 psig Stainless steel springs with silicone soft seat Viton O-ring seat, 3/4'' & 1'' only Maximum Temp. 325˚F A B National Board certified capacities for air and gas service in air compressors, air receivers and gas lines. Use key to designate last two digits of product number. Set Pressure PSIG 15 20 25 30 35 40 50 60 75 80 100 120 125 140 150 160 165 175 180 200 220 230 235 250 No. 15-112 15-115 15-117 15-118 15-119 Customer Service 1-704-841-6000 • Registered in all Canadian provinces and territories: CRN #0G2663.1C • ASTM B16 Brass Body Capacities in SCFM @ 10% Accumulation 15-112 15-115 & 117 15-118 1/4” 3/8" or 1/2" 3/4" 60 107 70 124 79 140 88 156 98 174 43 109 193 51 128 229 60 149 265 72 179 319 76 190 337 92 230 409 108 271 481 112 281 499 124 312 553 133 332 589 141 353 625 145 363 644 153 383 680 157 393 698 173 432 770 475 842 495 878 505 896 535 950 Inlet Size(in.) 1/4 NPT 3/8 NPT 1/2 NPT 3/4 NPT 1 NPT A(in.) 2-5/8 3-1/4 3-3/8 4-1/16 5-1/8 15-119 1" 222 256 290 323 361 398 473 547 659 696 845 995 1032 1144 1218 1293 1330 1405 1442 1591 1740 1815 1852 1964 B(in.) 2-5/32 1-1/8 1-1/8 1-7/32 1-7/8 Suffix No. -A2 -A0 -A1 -A3 -A5 -01 -B3 -02 -03 -04 -05 -06 -07 -08 -09 -10 -J1 -11 -12 -13 -14 -R8 -15 -16 Wt./100 (lbs) 18.5 42.2 45.3 58.0 153.0 33 Plumbing and Heating Section I & VIII ASME Safety Valves 19 Series Bronze Safety Valves for Steam, Air & Gas Service National Board capacity certified, high capacity, ideal for use with all types of boilers, pressure vessels, compressors and pressure piping systems. • • • • • Pressures: 15 through 300 psig steam, air, gas Max. temp. 406˚F, 422˚F with stainless steel trim 12 sizes, 1/2" thru 2-1/2" NPT Stainless steel spring Optional 316 stainless steel wetted trim (Specify 19L or 19S Series) • Metal to metal seat lapped to high degree optical flatness B • Less costly repairing, soft seat easily factory replaced • Double ring, full bore, high-capacity design • Tapped body drain facilitates piping of condensate away from equipment • Available in metal and soft seat designs • Registered in all Canadian provinces and territories CRN #0G2663.1C Specials A-Anti-Vibration X-Oxygen Clean A Information required for ordering 19 Series safety valves: •Inlet Size - male pipe thread Outlet Size - female pipe thread (if important) •Service Media (steam, air or gas) •Pressure Setting •Discharge Capacity •Type Service - Power Boiler - Pressure Vessel ASME Section I Steam Power Boiler - “V” steam Lbs./hr. steam @ 3% accumulation Ordering Number 19-X-XX-X-XXX-XX C Pressure Setting In PSIG Justified Left Trim Standard M-Brass/Metal Seat K-Brass/PFA “Soft” Seat No. 19KDC 19KDD 19KED 19KEE 19KFE 19KFF 19KGF 19KGG 19KHG 19KHH 19KJH 19KJJ Orifice Designation D D E E F F G G H H J J Set Pressure PSIG D 15 174 25 229 40 311 50 366 100 646 125 787 150 929 165 1014 200 1211 250 1494 300 1777 Approx 5.7 1 PSI increments Service A-Sect. I Steam K- Sect. VIII Air L-Sect. VIII Steam N-Non-Code Air P-Non-Code Steam Inlet Size C-1/2” D-3/4” E-1” F-1-1/4" G-1-1/2" H-2" J-2-1/2" Orifice Letter D G E H F J Optional L-SS/PFA “Soft” Seat S-SS/Metal Seat Size Inlet x Outlet 1/2 x 3/4 3/4 x 3/4 3/4 x 1 1x1 1 x 1-1/4 1-1/4 x 1-1/4 1-1/4 x 1-1/2 1-1/2 x 1-1/2 1-1/2 x 2 2x2 2 x 2-1/2 2-1/2 x 2-1/2 Wt./Ea. (lbs) 1.50 1.50 1.90 2.08 3.90 4.05 7.03 6.98 11.20 11.33 19.20 19.80 A(in.) 1-25/32 1-27/32 1-15/16 2-1/16 2-3/8 2-7/16 2-11/16 2-3/4 3-1/16 3-1/8 3-7/16 3-13/16 Dimensions B(in.) 6-1/8 6-3/16 6-5/8 6-3/4 8-13/16 8-7/8 10-3/16 10-1/4 11-5/16 11-3/8 13-5/8 14 C(in.) 1-1/16 1-1/16 1-3/4 1-3/4 2 2 2-3/8 2-3/8 2-3/4 2-3/4 3-1/2 3-1/2 E 310 408 555 653 1152 1404 1656 1807 2160 2664 3168 10.1 F 484 637 866 1019 1798 2191 2585 2821 3371 4158 4945 15.7 Orifice G 794 1045 1421 1672 2950 3595 4240 4628 5531 6822 8112 25.8 H 1240 1631 2217 2608 4602 5609 6616 7220 8630 10,644 12,658 40.3 J 2035 2677 3641 4283 7557 9210 10,864 11,856 14,170 17,477 20,784 66.1 *Specify Model 19S with stainless steel wetted trim for steam settings beyond 250 psig. 34 •-Other Suffixes Factory Issued Customer Service 1-704-841-6000 Plumbing and Heating Section I & VIII ASME Safety Valves 19 Series Bronze Safety Valves for Steam, Air & Gas Service ASME Section VIII Steam Unfired pressure Vessels “UV” steam Lbs./hr. @ 10% accumulation ASME Section VIII Air Unfired pressure Vessels - “UV” air Lbs./hr. @ 10% accumulation *Specify Model 19S with stainless steel wetted trim for steam settings beyond 250 psig. 29 Series Set Pressure PSIG D 15 179 25 234 40 322 50 382 100 684 125 835 150 985 165 1076 200 1287 250 1590 300 1892 Approx 6.0 1 PSI increments 15 64 25 83 40 115 50 136 100 244 125 297 150 351 165 383 200 459 250 566 300 673 Approx 2.2 1 PSI increments (continued) E 320 417 574 682 1220 1489 1758 1920 2296 2834 3373 10.8 F 499 652 896 1064 1904 2324 2744 2996 3584 4424 5265 16.8 Orifice G 819 1070 1471 1746 3124 3813 4502 4916 5881 7259 8639 27.6 H 1278 1669 2295 2725 4875 5950 7025 7670 9175 11325 13,479 43.0 J 2099 2741 3768 4474 8005 9770 11535 12594 15066 18596 22,132 70.6 114 149 204 243 434 530 626 683 818 1009 1201 3.8 178 232 319 379 678 828 977 1067 1276 1575 1874 6.0 292 381 524 622 1112 1358 1603 1750 2094 2584 3075 9.8 455 594 817 970 1736 2118 2501 2731 3267 4032 4798 15.3 747 976 1342 1593 2849 3478 4106 4484 5364 6621 7878 25.1 OEM Style Bronze Safety Valves For Steam, Air & Non-Hazardous Gas National Board capacity-certified; PFA Teflon™ seat resists corrosive boiler chemicals. Top-guided design with rustproofed steel stem and stainless steel springs. Features patented “soft” seat. • Capacity Certified 30 to 200 psig • Optional stainless trim (add “L” suffix) • Tapped body drain • No critical metal-to-metal seal • Compact design ideal for OEM applications • Registered in all Canadian provinces and territories. CRN#0G2663.1C ASME Code and Service No Suffix (Default) = Sec. I “V” Steam US = Sec. VIII “UV” Steam UA = Sec. VIII ”UV” Air A Ordering Number 29-XXX-XX-X-XX C B Information required for ordering 29 Series safety valves: • Inlet Size - male pipe thread Outlet Size - female pipe thread (if important) • Service Media (steam, air or gas) • Pressure Setting • Required Discharge Capacity • Type Service* - Power Boiler - Pressure Vessel *Note: Unless otherwise specified valve are furnshed with ASME Section I “V” steam rating. For ASME Section VIII applications add “US” suffix for UV steam or “UA” suffix for UV air. Optional Stainless Trim Add “L” suffix for Type 316 Stainless Steel Wetted Trim. Models 29-202 and 29-303 only Set Pressure Code See Table Inlet x Outlet Size 102 = 3/8 x 1 202 = 1/2 x 1 302 = 3/4 x 1 303 = 3/4 x 1-1/4 402 = 1 x 1-1/4 501 = 1-1/4 x 1-1/4 Size(in.) No. 29-102 29-202 29-302 29-303 29-402 29-501 Inlet 3/8 1/2 3/4 3/4 1 1-1/4 Outlet 1 1 1 1-1/4 1-1/4 1-1/4 Customer Service 1-704-841-6000 Wt./Ea. (lbs) 1.30 1.33 1.90 3.43 3.43 3.48 A(in.) 5-13/32 5-13/32 5-13/32 7-1/4 7-1/4 7-1/4 Dimensions B(in.) 1-1/4 1-1/4 1-1/4 1-11/16 1-11/16 1-11/16 C(in.) 2-1/8 2-1/8 2-1/8 2-3/4 2-3/4 2-3/4 35 Plumbing and Heating Section I & VIII ASME Safety Valves 29 Series OEM Style Bronze Safety Valves For Steam, Air & Non-Hazardous Gas (cont’d) Pressure PSIG 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 Suffix No. -07 -08 -09 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 Pressure PSIG 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 Suffix No. -24 -25 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 -41 -42 -43 -44 Set Pressure No. 50 75 100 125 150 200 Approx. 1 PSI increments 29-102 29-202 29-302 238 331 423 516 608 794 3.70 29-303 29-402 29-501 479 664 851 1036 1223 1596 7.40 ASME Section VIII Steam Unfired pressure Vessels - “UV” steam Lbs./hr. @ 10% accumulation 50 75 100 125 150 200 Approx. 1 PSI increments 251 350 448 547 646 844 3.95 504 704 902 1102 1299 1697 8.00 ASME Section VIII Air Unfired pressure Vessels - “UV” air SCFM @ 10% accumulation 50 75 100 125 150 200 Approx. 1 PSI increments 89 124 159 194 230 300 1.40 180 250 321 391 463 605 2.80 ASME Section I Steam Power Boiler “V” steam Lbs./hr. @ 3% accumulation 36 Customer Service 1-704-841-6000 Plumbing and Heating Section I & VIII ASME Safety Valves 119 Series Cast Iron Safety Valve Heavy-duty 119 Series cast iron valves are high capacity safety valves ideal for use with all types of boilers, pressure vessels and pressure piping systems. Their top guided design includes two control rings that ensure seat tightness. Direct replacement for most competitive models. • Set pressures to 250 psig @ 450˚ F maximum • Flanged inlet sizes: 1-1/2" through 6" ANSI 250 lb.; some sizes available in female NPT • National Board certified ASME flow ratings • Metal to metal seating, lapped to optical flatness • Semi-nozzle design comes in eight orifice sizes Base Model No. 119 JGC 119 KHC 119 KHA 119 KJC 119 LJC 119 LJA 119 LKC 119 MKA 119 MKC 119 NMD 119 PMD 119 QPD 119 RPD Valve Size(in.) 1-1/2 250# x 2 1/2 FNPT 2 250# x 3 FNPT 2 FNPT x 3 FNPT 2-1/2 250# x 3 FNPT 2-1/2 250# x 4 FNPT 2-1/2 FNPT x 4 FNPT 3 250# x 4 FNPT 3 FNPT x 4 FNPT 3 250# x 4 FNPT 4 250# x 6 125# 4 250# x 6 125# 6 250# x 8 125# 6 250# x 8 125# • Rust-proof steel stem, spring and spring washers • Drip pan elbows are available (see page 38) • Registered in all Canadian provinces and territories under CSA B51, CRN OG2663.1C • Optional 316 Stainless Steel wetted trim (disc and nozzle) specify 120 series Orifice Letter J K K K L L L M M N P Q R Orifice Area(sq. in.) 1.356 1.926 1.926 1.926 2.99 2.99 2.99 3.774 3.774 4.55 6.692 11.593 16.786 Dimensions(in.) A B C 15 4 4-5/16 16 4 4-5/8 16 4 4-5/8 16 4 4-5/8 22 5-1/8 5-5/8 22 5-1/8 5-5/8 22 5-1/8 5-5/8 22 5-1/8 5-5/8 22 5-1/8 5-5/8 28 7-1/4 6-3/4 28 7-1/4 6-3/4 42 10 9-1/4 42 10 9-1/4 Wt./Lbs. APP 35 36 3-3/4 37 41 84 5-3/8 81 85 5-3/8 80 87 210 215 530 530 Hex D Information required for ordering 119 series valves: 1. Determine the orifice letter that corresponds to your required flow rate from the following capacity charts. 2. Select the inlet x outlet connection options from the list of models available for that orifice (above). 3. Specify base model number, set pressure, ASME Code section and service. For Further information request brochure #PHBR119S Orifice J Orifice K Orifice L Set Press. Sec. I PSIG Lbs./Hr. 15 1947 30 2868 50 4096 75 5646 100 7227 125 8809 150 10390 175 11971 200 13552 225 15133 250 16714 VIII Stm. Lbs./Hr. 2008 2929 4280 5969 7657 9346 11034 12723 14412 16100 17789 VIII Air SCFM 715 1043 1523 2124 2726 3327 3928 4529 5130 5731 6332 15 30 50 75 100 125 150 175 200 225 250 2761 4067 5809 8008 10250 12493 14735 16978 19220 21463 23705 2848 4154 6070 8465 10860 13255 15650 18045 20440 22834 25229 1014 1479 2161 3013 3865 4718 5570 6423 7275 8128 8980 15 30 50 75 100 125 150 175 200 225 250 4286 6314 9018 12432 15913 19394 22876 26357 29838 33320 36801 4421 6449 9423 13141 16859 20577 24295 28013 31731 35449 39167 1574 2295 3354 4678 6001 7324 8648 9971 11294 12618 13941 Orifice M Orifice N Orifice P Customer Service 1-704-841-6000 Set Press. Sec. I PSIG Lbs./Hr. 15 5410 30 7969 50 11382 75 15691 100 20085 125 24480 150 28874 175 33268 200 37662 225 42056 250 46451 VIII Stm. Lbs./Hr. 5580 8140 11894 16587 21280 25973 30666 35358 40051 44744 49437 VIII Air SCFM 1986 2897 4234 5904 7574 9245 10915 12586 14256 15926 17597 15 30 50 75 100 125 150 175 200 225 250 6522 9608 13723 18918 24215 29513 34811 40108 45406 50704 56002 6728 9814 14340 19998 25655 31313 36971 42629 48287 53944 59602 2395 3493 5104 7118 9132 11146 13160 15173 17187 19201 21215 15 30 50 75 100 125 150 175 200 225 250 9592 14131 20183 27823 35615 43407 51199 58990 66782 74574 82366 9895 14434 21091 29412 37733 46055 54376 62697 71018 79340 87661 3522 5138 7507 10469 13431 16393 19355 22317 25278 28240 31202 Orifice Q Orifice R Set Press. Sec. I PSIG Lbs./Hr. 15 16617 30 24480 50 34964 75 48200 100 61698 125 75197 150 88695 175 102193 200 115691 225 129189 250 142687 VIII Stm. Lbs./Hr. 17141 25004 36537 50952 65368 79783 94199 108614 123030 137445 151861 VIII Air SCFM 6101 8900 13005 18136 23267 28398 33529 38660 43791 48923 54054 15 24061 24820 8834 30 35446 36205 12887 50 50628 52903 18830 75 69791 73776 26260 100 89336 94649 33689 125 108880 115522 41119 150 128425 136395 48549 175 147969 157267 55978 200 167514 178140 63408 225 187059 199013 70837 250 206603 219886 78267 ASME Section I - Steam Boilers Pounds of saturated steam per hour @ 3% or 2 psig accumulation, whichever is greater. ASME Section VIII - Pressure Vessels Pounds of saturated steam per hour @ 10% or 3 psig accumulation, whichever is greater. ASME Section VIII - Pressure Vessels Standard cubic feet of air per minute @ 10% or 3 psig, whichever is greater. 37 Plumbing and Heating Section I & VIII ASME Safety Valves Drip Pan Elbow The use of a drip pan elbow is highly recommended for steam service safety valves. When attached to a safety valve outlet, these elbows collect and remove condensate as well as isolate the valve from discharge piping stresses. Elbows through 4'' feature female NPT threads and connect to the valve outlet by means of a close nipple. The 6'' and 8'' elbows have integral 125# ANSI B16.1 flanges and bolt directly to the valve outlet. No. Q-5740-00 Q-5739-00 Q-5736-00 Q-5737-00 Q-5734-00 N-4098-00 N-4100-00 N-4102-00 N-4104-00 N-4106-00 Size(in.) 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 6 8 A 1-1/2 1-1/2 2 2 3 4 4 6 8 10 B 3-3/4 3-3/4 5-1/2 5-1/2 6-1/4 7-3/8 8 9-5/8 12-3/4 16-1/2 Dimensions(in.) C D E 1-5/8 2-1/4 1 1-5/8 2-1/4 1 2-1/8 3-3/8 1-1/2 2-1/8 3-3/8 1-1/2 2-1/4 3-5/8 1-5/8 3 4-3/8 1-7/8 3-1/2 4-7/8 2-1/8 4-1/2 5-3/4 2-5/8 6-5/8 7-5/8 3 7-1/2 8-5/8 4-1/8 F 1/4 1/4 3/8 3/8 1/2 3/4 3/4 3/4 3/4 1 G 1-1/2 1-1/2 2-1/8 2-1/8 2-1/4 2-3/4 3-1/8 3-1/4 8 10-3/4 Approx. Wt./Lbs. 2 2 5 5 7 11 17 30 84 151 Note: Ordering size of drip pan elbow is also nominal outlet size of safety valve. Section VIII ASME Safety Relief Valves 500 Series Versatile ASME Section VIII safety relief valve certified for steam, air/gas and liquid service. Choice of bronze, carbon steel or stainles steel bodies to suit a wide range of applications. • • • • • • Set pressures to 900 psig @ 800˚ F maximum Inlet sizes 1/2" through 2" Wide range of materials and options High capacity full - nozzle design Stainless steel springs are standard Short “tuned” blowdown • • • • • API 527 Seat tightness Back pressure tight bonnet design Pack lever and screwed cap designs One trim suitable for all types of service CSA B51 CRN OG2663.1C B Orifice Designation D D E E F F G G H H J No. 5XXDC 5XXDD 5XXED 5XXEE 5XXFE 5XXFF 5XXGF 5XXGG 5XXHG 5XXHH 5XXJH A C Size (in.) Inlet x Outlet 1/2 X 1 3/4 X 1 3/4 X 1-1/4 1 X 1-1/4 1 X 1-1/2 1-1/4 X 1-1/2 1-1/4 X 2 1-1/2 X 2 1-1/2 X 2-1/2 2 X 2-1/2 2X3 Flow Area(sq. in.) .1295 .1295 .2282 .2282 .3589 .3589 .5890 .5890 .9195 .9195 1.5044 A 2-3/8 2-3/8 2-5/8 2-5/8 2-7/8 2-7/8 3-1/4 3-1/4 3-1/2 3-1/2 4 Screwed Packed Cap Lever B B 7-1/2 7-1/2 7-1/2 7-1/2 9 9 9 9 10-1/4 10-1/4 10-1/4 10-1/4 13-1/4 13-1/4 13-1/4 13-1/4 15 15 15 15 17 17 C 1-5/8 1-5/8 2 2 2-3/8 2-3/8 2-5/8 2-5/8 2-3/4 2-3/4 3-1/4 Wt. Ea. (lbs.) 2 2 3 3 5 5 9 9.5 15.5 16 23 Model Numbering System 500 Series Safety Relief Valve POSITION 1 2 SERIES BODY/TRIM MAT'L 5 2 3 4 5 6 7 8 ORIFICE CAP 3 SIZE J INLET H CONNECTION B SERVICE K SEAT M B=MNPT X FNPT J=SEC VIII LIQUID M=METAL 51=BRONZE/BRASS 1=SCREWED CAP D C=1/2 52=BRONZE/ STAINLESS 2=SCREWED + GAG E D=3/4 53=CARBON/ STAINLESS 3=PACKED LEVER F E=1 54=ALL STAINLESS 4=PACKED + GAG G F=1-1/4 M=NON CODE LIQUID H G=1-1/2 N=NON CODE AIR / GAS J H=2 K=SEC VIII AIR L=SEC VIII STEAM K=TEFLON P=NON CODE STEAM Q=VACUUM 38 Notes: 1. The ASME Code Section VIII requires a lift lever for the following services: air, steam, or hot water over 140°F 2. Maximum back pressure is 50 psig. 3. High temperature stainless steel alloy spring is required above 422°F / 217°C. Specify option “HT” 4. Service limits for Teflon® seat: -330 to +450°F / -201 to 232°C 9 10 11 12 13 14 SPECIAL OPTIONS A A SET PRESSURE 0 4 2 5 FACTORY ISSUED SET PRESSURE, LETTERS / NUMBERS OR SPECIAL OPTIONS OR FEATURES PSIG (4 DIGITS) "AA"=DEFAULT STANDARD VACUUM "HT" HIGH TEMP. SPRING "HG" PREFIX+ 2 DIGIT Plumbing and Heating Section VIII ASME Safety Relief Valves 500 Series Set Press. PSIG D 15 188 20 216 25 245 30 274 35 305 40 337 45 368 50 400 55 431 60 463 65 494 70 526 75 558 80 589 85 621 90 652 95 684 100 715 125 873 150 1031 175 1189 200 1346 225 1504 250 1662 275 1820 300 1977 325 2135 350 2293 375 2451 400 2608 425 2766 450 2924 475 3082 500 3239 525 3397 550 3555 575 3713 600 3870 625 4028 650 4186 675 4344 700 4501 725 4659 750 4817 775 4975 800 5132 825 5290 850 5448 875 5606 900 5763 Approx. 1 psi Increment6.3 Versatile ASME Section VIII safety relief valve (continued) Orifice E F 331 520 381 600 432 679 482 759 538 846 593 934 649 1021 705 1108 760 1196 816 1283 872 1371 927 1458 983 1546 1038 1633 1094 1721 1150 1808 1205 1896 1261 1983 1539 2421 1817 2858 2095 3295 2373 3733 2651 4170 2929 4607 3207 5045 3485 5482 3763 5919 4041 6357 4319 6794 4597 7231 4875 7669 5153 8106 5431 8543 5709 8981 5987 9418 6266 9855 6544 10293 6822 10730 7100 7378 7656 7934 8212 8490 8768 9046 9324 9602 9880 10158 11.1 17.5 G 853 984 1114 1245 1388 1532 1676 1819 1963 2106 2250 2393 2537 2680 2824 2968 3111 3255 3972 4690 5408 6126 6843 7561 8279 8997 9714 10432 11150 11867 12585 13303 14021 14738 15456 16174 16892 17609 H 1332 1536 1740 1943 2168 2392 2616 2840 3064 3288 3512 3736 3960 4184 4408 4632 4857 5081 6201 7322 8442 9562 10683 11803 12924 14044 15165 16285 17405 18526 19646 20767 21887 23008 J 2180 2513 2846 3180 3546 3913 4280 4646 5013 5380 5746 6113 6479 6846 7213 7579 7946 8313 10146 11979 13812 15645 17478 19312 21145 22978 24811 26644 28477 30311 32144 33977 35810 37643 28.7 44.8 73.3 ASME Section VIII Steam - POUNDS PER HOUR OF SATURATED STEAM @ 10% OVERPRESSURE. NATIONAL BOARD CERTIFIED. Customer Service 1-704-841-6000 Set Press. PSIG D 15 67 20 77 25 87 30 97 35 109 40 120 45 131 50 142 55 154 60 165 65 176 70 187 75 198 80 210 85 221 90 232 95 243 100 255 125 311 150 367 175 423 200 479 225 535 250 592 275 648 300 704 325 760 350 816 375 872 400 928 425 985 450 1041 475 1097 500 1153 525 1209 550 1265 575 1321 600 1378 625 1434 650 1490 675 1546 700 1602 725 1658 750 1715 775 1771 800 1827 825 1883 850 1939 875 1995 900 2051 Approx. 1 psi Increment2.2 E 118 136 154 172 191 211 231 251 271 290 310 330 350 370 389 409 429 449 548 647 746 845 944 1043 1142 1240 1339 1438 1537 1636 1735 1834 1933 2032 2131 2230 2329 2428 2527 2626 2725 2824 2923 3022 3121 3220 3319 3418 3517 3616 F 185 213 242 270 301 332 363 395 426 457 488 519 550 581 612 644 675 706 862 1017 1173 1329 1484 1640 1796 1951 2107 2263 2418 2574 2730 2885 3041 3197 3352 3508 3664 3819 Orifice G 304 350 397 443 494 545 596 648 699 750 801 852 903 954 1005 1056 1107 1158 1414 1669 1925 2180 2436 2691 2947 3202 3458 3713 3969 4224 4480 4735 4991 5246 5501 5757 6012 6268 4 6.2 10.2 H 474 547 619 692 772 851 931 1011 1091 1170 1250 1330 1410 1489 1569 1649 1729 1808 2207 2606 3005 3404 3802 4201 4600 4999 5398 5796 6195 6594 6993 7392 7791 8189 J 776 895 1013 1132 1262 1393 1523 1654 1784 1915 2045 2176 2306 2437 2567 2698 2828 2959 3611 4264 4916 5569 6221 6874 7526 8179 8831 9484 10136 10789 11441 12094 12746 13399 16 26.1 ASME Section VIII Air - STANDARD CUBIC FEET OF AIR PER MINUTE @ 10% OVERPRESSURE. NATIONAL BOARD CERTIFIED. 39 Plumbing and Heating 500 Series (cont’d) Set Press. PSIG D 15 14 20 16 25 18 30 19 35 21 40 22 45 24 50 25 55 26 60 28 65 29 70 30 75 31 80 32 85 33 90 34 95 35 100 36 125 40 150 44 175 47 200 50 225 53 250 56 275 59 300 62 350 66 E 25 29 32 34 37 40 42 44 46 48 50 52 54 56 58 59 61 63 70 77 83 89 94 99 104 108 117 Orifice F 40 45 50 54 58 62 66 70 73 76 79 82 85 88 91 93 96 98 110 121 130 139 148 156 163 171 184 G 65 74 82 89 96 102 108 114 120 125 130 135 140 145 149 153 158 162 181 198 214 229 242 256 268 280 302 Versatile ASME Section VIII safety relief valve (continued) H 102 115 127 138 149 160 169 178 187 195 203 211 218 226 233 239 246 252 282 309 334 357 378 399 418 437 472 Set Press. PSIG D 325 64 375 69 400 71 425 73 450 75 475 77 500 79 525 81 550 83 575 85 600 87 625 89 650 91 675 92 700 94 725 96 750 97 775 99 800 100 825 102 850 104 875 105 900 107 J 167 189 208 226 244 261 277 292 306 320 333 345 357 369 381 392 402 413 462 506 546 584 619 653 685 715 772 E 113 121 125 129 133 136 140 143 147 150 153 157 160 163 166 169 171 174 177 180 183 185 188 Orifice F 178 191 197 203 209 215 220 226 231 236 241 G 291 313 323 333 343 352 361 370 379 388 396 H 455 489 505 520 535 550 564 J 744 799 826 851 876 900 923 Note: To determine water capacity at 25% overpressure, multiply the capacity at 10% by 1.066. ASME Section VIII WATER - US GALLONS PER MINUTE OF WATER @ 10% OVERPRESSURE. NATIONAL BOARD CERTIFIED. Gas Cocks GB-10 Series CSA Gas Shutoff Valves Manual shut-off valves engineered specifically for low-pressure gas service. Canadian Standard Association Design and capacity certified with American-made quality. High-copper content body, chrome-plated ball, PTFE seats. • Complies with ANSI Z21.15.CGA9.1-M97, and AGA 388, and CR91-002 standards for 1/2 psig and 5 psig installations • Lever or tee handle options available • Use with natural, manufactured, mixed and liquefied petroleum gases, LP gas-air mixtures • Standard die-cast zinc “wing” handle, epoxy coated, for easy shut off No. 3/8" GB-10 1/2" GB-10 3/4" GB-10 1" GB-10 Connection 3/8 NPT 1/2 NPT 3/4 NPT 1 NPT BTU/Hr* 318700 623750 1265000 2037500 * Capacity based on a gas having a heating value of 1000 Btu/cubic feet and an S.G. of 0.64 at a P.D. of 1” W.C. Valve Size (in.) 3/8 1/2 3/4 1 A 2.04 2.24 2.97 3.33 B 1.06 1.18 1.55 1.81 C 2.86 2.99 3.85 N/A Dimensions(in.) D E F 0.38 0.38 3.85 0.5 0.5 3.85 0.69 0.75 4.75 0.88 1 4.75 Handle Options: Lever, add suffix -L1; Tee, add suffix -T1 to model number. 40 Customer Service 1-704-841-6000 G 2.24 2.3 2.85 3.1 H 2.2 2.24 2.9 3.15 J 0.81 0.81 1 1 Plumbing and Heating Gas Cocks GB-12, GB-13, GB-14, GB-15, GB-16 Series These gas appliance ball valves are designed for natural gas, manufactured and mixed gas, liquefied petroleum gases and LP gas-air mixture applications. They comply with the latest editions of these published standards: • ANSI Z21.15.CGA9.1 • AGA No. 3-88 • UL Guide YRBX • UL Guide MHKZ • UL Guide YRPV • UL Guide YSDT No. GB-12 GB-12 GB-12 GB-12 GB-13 GB-13 GB-13 GB-14 GB-14 UNIBODY SERIES GB-15 GB-15 GB-15 GB-16 GB-16 GB-50 & GB-50A Series Part # 51GC2T1 51GC3T1 51GC4T1 51GC5T1 51GD2T1 51GD3T1 51GD4T1 51GE2T1 51GE3T1 Size & End Connection 3/8" FNPT x FNPT 1/2" FNPT x FNPT 3/4" FNPT x FNPT 1" FNPT x FNPT 1/2" x 3/8" FNPT x Flare 1/2" x 1/2" FNPT x Flare 3/4" x 5/8" FNPT x Flare 3/8" x 3/8" Flare x Flare 1/2" x 1/2" Flare x Flare 51GF201 51GF301 51GF401 51GG201 51GG301 3/8" FNPT x 3/8" FNPT 1/2" FNPT x 1/2" FNPT 3/4" FNPT x 3/4" FNPT 1/2" FNPT x 3/8" Flare 1/2" FNPT x 1/2" Flare CSA Gas Shutoff Ball Valves Designed for indoor “main burner” applications, with cast-in single or dual pilot tap for faster, simpler installation. Fully complies with AGA.3-88, ANSI Z21.15.CGA9.1-M97, single or dual and CR91-002 standards. ASTM B584 bronze body, chrome-plated ball, brass stem, retainer and gland screws for corrosion resistance. • For natural gas, manufactured and mixed gas, liquefied petroleum gases and LP gas-air mixtures • Rated pressures of 1/2 and 5 psig • High capacity No. Single Tapped 50GB301 50GB401 50GB501 50GB601 50GB701 50GB801 50GB5A1 50GB6A1 50GB7A1 50GB8A1 Dual Tapped -50GB401A 50GB501A 50GB601A 50GB701A 50GB801A 50GB5A1A 50GB6A1A 50GB7A1A 50GB8A1A • Comes standard with a reversible plated steel lever handle. Options include a die-cast zinc “wing” handle and “tee” handle • Standard connection is FNPT x FNPT Dimensions(in.) Size (in.) Tapping A B C D 1/2 1/8 .50 1.11 2.25 1.68 3/4 1/8 .75 1.26 2.67 1.93 1 1/8 1.00 1.65 3.42 2.19 1-1/4 1/8 1.25 1.87 3.86 2.37 1-1/2 1/8 1.50 2.50 4.22 2.78 2 1/8 2.00 2.48 5.02 3.15 1 1/4 1.00 1.65 3.42 2.19 1-1/4 1/4 1.25 1.87 3.86 2.37 1-1/2 1/4 1.50 2.50 4.22 2.78 2 1/4 2.00 2.48 5.02 3.15 E 2.85 3.85 4.78 4.78 5.50 5.50 4.78 4.78 5.50 5.50 F 2.27 2.72 3.56 3.56 4.18 4.90 3.56 3.56 4.18 4.90 G 1.00 1.12 1.53 1.62 1.81 2.18 1.53 1.62 1.81 2.18 H 2.24 3.06 3.24 3.62 4.36 3.06 3.24 3.62 4.36 Capacity BTU/Hr. 693,000 1,258,000 3,144,000 6,441,000 7,745,000 14,741,000 3,144,000 6,441,000 7,745,000 14,741,000 *Note: Capacities based on 1000 Btu/cubic feet gas at 0.64 specific gravity, at a P.D. of 1'' W.C. G H Customer Service 1-704-841-6000 41 Plumbing and Heating Gas Cocks 46-100 Series Standard Cocks Wrench operated model with square head and 125 psig rating. Sizes from 1/4" FNPT to 1" FNPT. No. 46-101-01 46-102-01 46-103-01 46-104-01 46-105-01 50 Series Wt./100 (lbs.) 33 30 48.2 66 173.8 Size(in.) 1/4 3/8 1/2 3/4 1 Manual Main Control Valves CSA design certified for 1/2 psig and temperatures from 32° to 125°F. Complies to ANSI Z 21.15.CGA 9.1-M97. • Factory tested 100% at 10 psig • Bronze construction, stainless steel springs No. 50-203 50-303 50-403 50-503 50-603 50-703 50-803 Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 Handle Suffix Position • Capacities to 7.8 million Btu/hour • Equal female inlet/outlet BTU/Hr. 800,000 1,310,000 2,100,000 3,250,000 3,700,000 7,300,000 7,800,000 Size Pilot 1/8 NPT 1/4 NPT Wt./100 (lbs) 88 156 197 300 478 845 1000 W 01 05 A(in.) 2-1/2 2-15/16 3-5/16 3-21/32 4-3/8 5-7/16 5-7/8 Dimensions B(in.) C(in.) 1-7/16 1-23/32 1-11/16 2-1/16 2-3/16 2-7/8 2-3/4 3-5/32 3-5/16 3-1/2 3-23/32 4-1/2 3-23/32 4-1/2 D(in.) 2-3/4 3-1/2 3-7/8 4-11/16 5-3/4 6-3/4 6-3/4 Y 03 07 Z 04 08 X 02 06 All main burner valves furnished with 1/8” NPT pilot tapping. Valves 1” and larger can be furnished with 1/4” NPT pilot tapping. 51 Series Gas Service Cocks Tee or lever handle cocks; CSA design certified. In sizes 1/4" to 3/4". • Capacities: 117,000 to 749,000 Btu/hour • Designed to meet ANSI Z21.15.CGA 9.1 requirements of 1/2 psig at temperatures from 32° F to 125°F T-Handle with Stop Lever Handle w/Stop 42 • Accepted for use in City of New York Department of Buildings MEA 45-90-M No. 51-103-01 51-104-01 51-105-01 51-106-01 Pipe Size(in.) 1/4 3/8 1/2 3/4 Wt./100 (lbs) 35 47 54 83 Capacity (BTU/Hr.) 117,000 274,600 274,000 749,000 51-107-01 51-108-01 51-109-01 3/8 1/2 3/4 50 56 87 274,600 274,600 749,000 Customer Service 1-704-841-6000 Plumbing and Heating Gas Cocks Gas Service Cocks 52 Series Available with tee head, flat head, square head or lever head in sizes from 1/4" to 1". Wrench operated and tested at 35 psig. • Nut and washer bottom with stop T-Head Flat Head 53 Series : • For operation up to 500°F No. 52-101-01 52-102-01 52-103-01 52-104-01 52-105-01 Size(in.) 1/4 3/8 1/2 3/4 1 Wt./100 (lbs.) 32 29 45 65.8 92.9 52-201-01 52-202-01 52-203-01 52-204-01 52-205-01 1/4 3/8 1/2 3/4 1 30 28 43 57 90.6 Square Head Lever Head No. 52-301-01 52-302-01 52-303-01 52-304-01 52-305-01 Size(in.) 1/4 3/8 1/2 3/4 1 Wt./100 (lbs.) 31 28 43 62.7 90 52-401-01 52-402-01 52-403-01 52-404-01 52-405-01 1/4 3/8 1/2 3/4 1 34.3 31 46 66.7 97 Gas Cocks Available in male and female sizes: 1/8", 1/4" and 3/8". No. 53-299-01* 53-300-01* 53-301-01 Male Size(in.) 1/8 1/4 3/8 Female Size(in.) 1/8 1/4 3/8 Wt./100 (lbs) 14 18.5 45 * Design certified by CSA to meet ANSI Z21.15.CGA 9.1 pressure requirements of 1/2 psig 54 Series Gas Hose Cocks & Appliance Connector Valve CSA design certified brass and wood handled valves with 56,500 Btu/hour capacity. No. Pipe Size(in.) Handle 3/8 Brass 54-101-01 54-102-01 1/2 Brass 54-103-01 3/4 Brass 54-104-01 3/8 Wood 54-105-01 1/2 Wood 54-106-01 3/4 Wood 54-201-01 3/8 3/8 SAE 54-202-01 1/2 3/8 SAE Wt./100 (lbs) 41 34.8 40 41 38 44.3 36 33.4 No. Pipe Size(in.) Handle 1/2 1/2 SAE 54-203-01 54-204-01 3/4 1/2 SAE 54-206-01 3/4 5/8 SAE 54-207-01 1/2 5/8 SAE 54-208-01 3/4 3/8 SAE 54-209-01 3/4 1/2 MNPT 54-401-01 3/8 *3/8 SAE 54-402-01 1/2 *3/8 SAE Wt./100 (lbs) 35 45.1 50 57 44 44 35 33 * Flared end threaded 9/16 thread 55-302 Series Gas Cock with Throttle Adjustment Design certified by CSA • Designed to meet ANSI Z21.15.CGA9.1-M97 pressure requirements of 1/2 psig No. 55-302-01 Customer Service 1-704-841-6000 • Thread size: 1/4 male x 1/4 female Size(in.) 1/4 M x 1/4 F Wt./100 (lbs.) 33 43 Plumbing and Heating Gas Cocks 56 Series Pilot Cocks Wide variety of CSA design certified pilot cocks. Designed to meet ANSI Z21.15.CGA 9.1-M97 pressure requirements of 1/2 psig at temperatures from 32˚ to 125˚ F. 56-111-01 56-112-01 Thread Size 1/8 NPT x 1/4 Tube Plain 1/8 NPT x 1/4 Tube Throttle Adjust. 1/8 NPT x 1/8 FNPT Plain 1/8 NPT x 1/8 FNPT Throttle Adjust. 1/8 NPT x 1/4 Tube 1/8 NPT x 1/4 Tube Right Hand 1/8 NPT x 1/4 Tube RH Throttle Adjust 1/8 NPT x 1/4 Tube Left Hand. 1/8 NPT x 1/4 Tube LH Throttle Adjust. No. 56-111-01 56-112-01 56-221-01 56-222-01 56-302-01* 56-601-01 56-602-01 56-603-01 56-604-01 Wt./100 (lbs.) 15.0 14.0 16.1 16.1 8.0 17.0 17.0 17.0 17.0 * Not CSA Certified 56-221-01 56-302-01 56-602-01 Water Gauges & Accessories 20-100 & 20-150 Series Standard Pattern Bronze Water Gauges Use for all types of liquid level verification; available with 3/8" or 1/2" NPT male pipe connections. Aluminum or plastic composition hand wheels; EPDM gauge glass gaskets standard. • Ball checks standard for 20-150 models • Equipped with two brass guard rods No. 20-101 20-102 20-104 20-105 20-150 20-151 • Rated: 125 psig @ 350°F, 300 psig @ 100°F (See note!) • CRN Registered Pipe Size 3/8 3/8 1/2 1/2 1/2 1/2 Glass O.D. & Length 5/8 x 10 5/8 x 10 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 Wt./100 (lbs.) 145 145 160 160 160 160 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 44 Customer Service 1-704-841-6000 Plumbing and Heating Water Gauges & Accessories 20-200, 20-250 & 25-200 Series Heavy Pattern Bronze Water Gauges All standard 20 Series features but with a heavier valve body pattern for higher service ratings. • Available with 3/8, 1/2 and 3/4 MNPT fittings • Ball checks standard on 20-250 models • Polished finish on 25-200 valves No. 20-201 20-202 20-204 20-205 20-207 20-208 20-250 20-251 20-253 20-254 25-201 25-202 25-204 25-205 25-207 25-208 Pipe Size(in.) 3/8 3/8 1/2 1/2 3/4 3/4 1/2 1/2 3/4 3/4 3/8 3/8 1/2 1/2 3/4 3/4 • Rated: 200 psig @ 400°F, 400 psig @ 100°F (See note!) • CRN Registered Glass O.D. & Length 5/8 x 10 5/8 x 10 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 5/8 x 10 5/8 x 10 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 Wt./100 (lbs.) 185 189 205 205 270 270 195 200 355 360 180 185 190 190 290 295 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 20-300, 20350, 25-400 & 25-500 Series Square Pattern Bronze Water Gauges Available with 1/2" (ASTM B-16 brass bar stock) or 3/4" (B-584 cast bronze) NPT male pipe connections. Four guard rods and EPDM gauge glass gaskets standard. Other packings available. • • • • Standard 1/4" needle drain valve in lower arm Pet cock or Apollo® ball valve drain on request Polished finish on 25-400 and 25-500 Ball checks standard on 20-350 and 25-500 No. 20-304 20-305 20-307 20-308 20-350 20-351 20-353 20-354 25-404 25-405 25-407 25-408 25-501 25-502 25-504 25-505 Pipe Size(in.) 1/2 1/2 3/4 3/4 1/2 1/2 3/4 3/4 1/2 1/2 3/4 3/4 1/2 1/2 3/4 3/4 • Rated: 200 psig @ 400°F, 400 psig @ 100°F (See note!) • CRN Registered Glass O.D. & Length 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 Wt./100 (lbs.) 260 270 345 365 265 265 360 365 285 285 350 350 290 290 355 355 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. Customer Service 1-704-841-6000 45 Plumbing and Heating Water Gauges & Accessories 20-400 & 20-410 Series Side Mounted Handwheel Water Gauges Side-mounted handwheels allow water gauge operation in hard to reach places; with all the 20 Series design features. • • • • • Ideal for concealed jacketed type boilers No guard rod brackets: 20-405, 20-406, 20-410 Brackets and guard rods standard: 20-407, 20-408 EPDM standard gauge glass gasket Compact - requires minimum space Pipe No. Size(in.) 1/2 20-405-00 RH 20-406-00 LH 1/2 20-407-00 RH 1/2 20-408-00 LH 1/2 20-410-00 LH 1/2 • Rated: 125 psig @ 350°F, 300 psig @ 100°F (See note!) • Angle type for use on concealed jacketed type boilers • 1-1/4'' Extended shank length; 20-410 • CRN Registered Glass O.D. & Length 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 Wt./100 (lbs.) 165 165 170 170 180 Wheel Type ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 20-700 & 20-710 Series Simple Expansion Tank Gauges Available with 3/8" or 1/2" MNPT connections; EPDM gauge glass gaskets and 1/4" needle drain valve in lower arm are both standard. • 20-710 has plug in top arm to insert glass straight through • 1/4" pet cock or Apollo® ball valve optional • Ball checks on request (20-704 only) No. 20-703-00 20-704-00 20-713-00 20-714-00 Pipe Size(in.) 3/8 1/2 3/8 1/2 • Rated: 125 psig @ 350°F, 300 psig @ 100°F (See note!) • CRN Registered Glass O.D. & Length 5/8 x 10 5/8 x 12 5/8 x 10 5/8 x 12 Wt./100 (lbs.) 120 135 120 135 Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 46 Customer Service 1-704-841-6000 Plumbing and Heating Water Gauges & Accessories 23-600 Series Stainless Steel Expansion Tank Gauges Holds all 316 stainless steel-compatible liquids. In lower arm: shut-off valve and stainless steel drain valve. • Two stainless steel guard rods • Rated: 250 psig at 406°F: maximum working pressure (See note!) No. 23-651-00 23-654-00 Pipe Size(in.) 1/2 3/4 • High pressure glass standard • CRN Registered Glass O.D. & Length 5/8 x 12 5/8 x 12 Wt./100 (lbs.) 225 225 Wheel Type ALUMINUM COMPOSITION Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 20-600 & 20-800 Series Bronze Expansion Tank Gauges Bottom arm shut-off valve prevents water leaks during gauge glass changes. • EPDM standard gauge glass gasket • 20-800 models: 1/4" NPT pipe thread in upper arm for pressure gauge standard No. 20-604-00* 20-605-00* 20-804-00* 20-805-00* Pipe Size(in.) 1/2 1/2 1/2 1/2 • Rated: 200 psig @ 400°F, 400 psig @ 100°F (See note!) • CRN Registered Glass O.D. & Length 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 Wt./100 (lbs.) 155 175 175 175 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION *Automatic model Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. Customer Service 1-704-841-6000 47 Plumbing and Heating Water Gauges & Accessories 20-600, 24-600 & 24-650 Series Chain Lever Water Gauges Lever on standard 12-foot chain allows operator to open and close valves that would be beyond reach. Valve stems operate on quarter-turns. • Rated 250 psig @ 400°F, 500 psig @ 100°F (See note!) • Use on large boilers with inconvenient columns • Automatic and non-automatic models No. 20-601-00** 20-602-00** 24-601-00 24-602-00 24-651-00* 24-652-00* Pipe Size(in.) 1/2 3/4 1/2 3/4 1/2 3/4 • Furnished with 12 feet of chain • High pressure glass standard with the 24 series • CRN Registered Glass O.D. & Length 5/8 x 12 3/4 x 16 5/8 x 12 3/4 x 16 5/8 x 12 3/4 x 16 Wt./100 (lbs.) 370 435 515 580 515 580 * Automatic model ** Ball valve not included Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 25-600 Series Chain Lever Water Gauges • Quick opening, non-automatic • Service rating: 250 psig @ 400°F, 500 psig @ 100°F (See note!) • EPDM standard gauge glass gasket No. 25-601-00* 25-602-00* Pipe Size(in.) 1/2 3/4 • Furnished with 12 feet of chain • H-2485 pull handle available • CRN Registered Glass O.D. & Length 5/8 x 12 3/4 x 16 Wt./100 (lbs.) 335 350 * Polished Finish Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 48 Customer Service 1-704-841-6000 Plumbing and Heating Water Gauges & Accessories 24-300 Series Bronze Liquid Level Gauges Automatic and non-automatic direct reading gauges in shank pipe sizes 1/2" and 3/4". • Heavy pattern bronze valve body • Guard rod bracket to accommodate four guard rods • Drain valve - 5/16 diameter full-blow ball valve with safety handle • PTFE reinforced gauge glass gasket and stem packing are standard NonAutomatic Automatic • Rated 500 psig @ 100°F, 250 psig @ 400°F (See note!) • Automatic - conforms to ASME power boiler code requirements for automatic water gauges; ball checks in upper and lower arms • High pressure gauge glass and gaskets are standard • CRN Registered No. 24-301-00 24-302-00 24-304-00 24-305-00 Pipe Size(in.) 1/2 1/2 3/4 3/4 Glass O.D. & Length 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 Wt./100 (lbs.) 425 425 490 490 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION 24-350-00 24-351-00 24-353-00 24-354-00 1/2 1/2 3/4 3/4 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 425 425 490 490 ALUMINUM COMPOSITION ALUMINUM COMPOSITION Regular gauge glass is used in the standard water gauges unless otherwise noted as high pressure Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. 21 Series Rough Bronze Water Gauges With Extended Shank • 1-3/4" standard shank length; for 1-1/4" shank length, use – 07 suffix • 21-100 rated 125 psig @ 350°F, 300 psig @ 100°F No. 21-101 21-102 21-104 21-105 21-150* 21-151* 21-204 21-205 21-250* 21-251* Pipe Size(in.) 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 • 21-200 rated 200 psig @ 400°F, 400 psig @ 100°F (See note!) • CRN Registered Glass O.D. & Length 5/8 x 10 5/8 x 10 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 5/8 x 12 Wt./100 (lbs.) 163 175 185 197 195 207 215 219 215 215 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION * Automatic Model Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. Customer Service 1-704-841-6000 49 Plumbing and Heating Water Gauges & Accessories 23-400 & 23-450 Series Stainless Steel Liquid Level Gauges Ideal for handling alcohol solvents, acetic acid and ketones. Automatic models conform to ASME requirements; aluminum and composition handwheels. • PTFE reinforced gauge glass, stem packings • Chemical resistant PTFE seat • 5/16 dia. full flow all SS drain valve with safety handle NonAutomatic Automatic • Guard rod bracket to accommodate four SS guard rods • Rated 500 psig @ 450°F (See note!) • High pressure gauge glass standard • CRN Registered No. 23-401-00 23-402-00 23-404-00 23-405-00 Pipe Size(in.) 1/2 1/2 3/4 3/4 Glass O.D. & Length 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 Wt./100 (lbs.) 385 385 450 450 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION 23-450-00 23-451-00 23-453-00 23-454-00 1/2 1/2 3/4 3/4 5/8 x 12 5/8 x 12 3/4 x 16 3/4 x 16 390 390 455 455 ALUMINUM ball checks COMPOSITION ball checks ALUMINUM ball checks COMPOSITION ball checks Note: Service ratings are subject to pressure/temperature ratings of gauge glass and glass gaskets. Tubular Gauge Glass Protector Reduces risk of injury and damage from broken exploding glass; maximum length: 50". • No. I-2733* 5/8" Glass Protector • No. I-2734* 3/4" Glass Protector • Made to fit most water gauges • Not available on 23-400, 23-650, 24-300, 24-600 models • CRN Registered Note: Water gauge part number and centerline length are required when ordering. Priced according to length and application. 50 Customer Service 1-704-841-6000 Plumbing and Heating Water Gauges & Accessories Ordering Water Gauge Glasses & Guard Rods • Standard, Red Line and High Pressure glass, sizes 5/8" and 3/4", are available in lengths to 72" • 3/16 diameter guard rod lengths from 6" to 74" • Call for more pressure and temperature ratings Suffix Key -00- Standard Gauge w/Standard Glass & Rod -01- Top only -02- Bottom only -03- Standard Gauge Less Glass and Rod -10- For Special Gauges and Gauges with Non-Standard Glass and Rod Lengths Formula for determining glass and rod lengths • Glass Length = (C to C Dimension) - 1-1/4" • Rod Length = (Glass Length) + 2" Exceptions (20-300, 20-350, 20-601, 20-602, 23-650, 24-300, 25-400, 25-500, 25-600) • Glass Length = (C to C Dimension) - 2" • Rod Length = (Glass Length) + 1-1/4" NOTE! Service ratings are subject to pressure/temp. ratings of gauge glass and gaskets. Regular gauges standard unless otherwise noted as high pressure. (23-400, 24-400, 24-600) • Glass Length = (C to C Dimension) - 2" • Rod Length = (Glass Length) + 7/8" Repair Kit Ordering Information 20-00-X-XX (20-207, 20-208, 20-253, 20-254) • Glass Length = (C to C dimension) - 1-1/2" • Rod Length = (Glass length) + 2-1/4" Designation 20-00=Water gauge repair kit Gauge Glass Service Ratings Size Standard 5/8" O.D. +0,-3/64" Wall 5/64" High Pressure O.D. +0,-1/32" Wall 3/32"±1/64" 3/4" O.D. +0,-1/32" Wall 7/64"±1/64" Red Line 5/8" O.D. +0,-1/32" Wall 3/32"±1/64" 3/4" O.D. +0,-1/32" Wall 3/32"±1/64" Length Temperatures Up to 150˚F No Corrosion Steam Boiler Services up to 425˚F 8" 10" 12" 14" 16" 210 210 205 200 195 100 100 100 100 100 8" 10" 12" 14" 16" 8" 10" 12" 14" 16" 435 420 410 390 375 425 410 400 385 370 320 315 305 295 285 315 310 300 290 280 8" 10" 12" 14" 16" 8" 10" 12" 14" 16" 370 345 335 325 315 360 340 330 320 310 285 280 280 275 270 280 275 275 270 265 Customer Service 1-704-841-6000 Kit Type 1=Standard All 2=Viton gaskets only 3=Graphite gaskets only Kit No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 51 Plumbing and Heating Water Gauges & Accessories Water Gauge Repair Kits Kit 20-001-01, 20-003-01 20-001-02, 20-003-02 20-001-03, 20-003-03 20-001-04, 20-003-04 20-001-05, 20-003-05 20-001-06, 20-003-06 20-001-07, 20-003-07 20-001-08, 20-003-08 20-001-09, 20-003-09 20-001-10, 20-003-10 20-001-11, 20-003-11 20-001-12, 20-003-12 20-001-13, 20-003-13 20-001-14, 20-003-14 26-100 & 26-300 Series Applications 20-101, 20-102, 20-104, 20-105, 20-150, 20-151, 20-405, 20-406,20-407, 20-408, 20-410, 21-101, 21-102, 21-104, 21-105, 21-150, 21-151 20-201, 20-202, 20-204, 20-205, 20-250, 20-251, 20-304, 20-305, 20-350, 20-351, 20-604, 20-605, 20-804, 20-805, 21-204, 21-205, 21-250, 21-251, 25-201, 25-202, 25-204, 25-205, 25-404, 25-405, 25-501, 25-502 20-207, 20-208, 20-253, 20-254, 20-307, 20-308, 20-353,20-354, 25-207, 25-208, 25-407, 25-408, 25-504, 25-505 20-601, 25-601 20-602, 25-602 20-703, 20-704, 20-713, 20-714 23-401, 23-402, 23-450, 23-451 20-405, 20-406, 20-407, 20-408 23-404, 23-405, 23-453, 23-454 23-651, 23-654 24-301, 24-302, 24-350, 24-351, 24-450, 24-451 24-304, 24-305, 24-353, 24-354, 24-453, 24-454 24-601, 24-651, 24-751, 24-851 24-602, 24-652, 24-752, 24-852 20-002-01 20-002-02 20-002-03 20-002-04 Standard repair kits and graphite repair kits contain glass packing, stem packing, friction washers, seat washers, and drain washer applicable to the particular valve. Three types of glass packing, EPDM rubber, Hypalon™, and PTFE, are included in the standard repair kit. For oil related service, Fluoroelastomer (Viton®) glass gasket sets are available. For severe applications, graphite glass gaskets and stem packing sets are available for each model. Compression Gauge Cocks For draining expansion tanks, other liquid storage vessels. • 26-100: rated up to 125 psig • 26-300: soft metal seat/stuffing box rated up to 250 psig 26-300 20-101, 20-102, 20-104, 20-105, 20-150 20-151, 20-201, 20-202, 20-204, 20-205, 20-250, 20-251, 20-304, 20-305, 20-350, 20-351, 20-405, 20-406, 20-407, 20-408, 20-410, 20-601, 20-604, 20-605, 20-703, 20-713, 20-704, 20-714, 20-804, 20-805, 21-101, 21-102, 21-104, 21-105, 21-150, 21-151, 21-204, 21-205, 21-250, 21-251, 23-651, 23-654, 25-201, 25-202, 25-204, 25-205, 25-404, 25-405, 25-501, 25-502, 25-601 20-207, 20-208, 20-253, 20-254, 20-307 20-308, 20-353, 20-354, 20-602, 25-207, 25-208, 25-407, 25-408, 25-504, 25-505, 25-602 23-401, 23-402, 23-450, 23-451, 24-301 24-302, 24-350, 24-351, 24-450, 24-451, 24-601, 24-651, 24-751, 24-851 23-404, 23-405, 23-453, 23-454, 24-304 24-305, 24-353, 24-354, 24-453, 24-454, 24-602, 24-652, 24-752, 24-852 No. 26-101 26-102 26-104 26-105 26-301 26-302 26-304 26-305 26-307 26-308 26-311 26-312 26-314 26-315 26-317 26-318 Pipe Size(in.) 3/8 3/8 1/2 1/2 3/8 3/8 1/2 1/2 3/4 3/4 3/8 3/8 1/2 1/2 3/4 3/4 • 26-310: stainless steel ball seat/stuffing box rated up to 250 psig Wt./100 (lbs.) 25.0 30.0 28.3 30.0 39.0 40.0 40.0 44.0 49.0 51.7 39.0 42.0 40.0 44.0 50.0 50.0 *26-100 series is not available with packing nut Specify the following suffix for finish: 01 - Satin Brass; 28 - Polished Brass. 52 Customer Service 1-704-841-6000 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION ALUMINUM COMPOSITION Plumbing and Heating Water Gauges & Accessories 26-500 Series Chain Operated Gauge Cocks For use on water columns beyond reach from the floor. • Spring loaded lever • PTFE seat • Optional 6-foot chain (suffix -02) • Rated up to 250 psig No. 26-504-01 26-507-01 26-700 Series Wt./100 (lbs.) 110 115 Size(in.) 1/2 3/4 PTFE Seat Compression Gauge Cock PTFE seat and stuffing box provide positive seal. • Rated up to 250 psig No. 26-704-01 26-705-01 26-707-01 26-708-01 Wt./100 (lbs.) 78.0 81.5 88.0 105.0 Size(in.) 1/2 1/2 3/4 3/4 Wheel Type ALUMINUM COMPOSITION ALUMINUM COMPOSITION Air & Drain Cocks 41 Series Air Cocks (for air use only) An economical way to shut off air lines. Nut bottom available for pressures to 200 psig with 1/8" port. Many handle configurations. Spring bottom with 5/32" port standard. • Spring bottom cocks tested at 80 psig air • Available in satin or polished brass or satin chrome Type Standard Nut Bottom Satin Brass -01 -04 Polished Brass -05 -08 No. tee handle round shoulder tee handle hexagon shoulder 41-060 41-070 41-080 41-090 41-120 41-130 41-140 41-150 lever handle round shoulder • Maximum temperature is 500˚F Satin Chrome -17 -20 Size(in.) TEE HANDLE ROUND SHOULDER 1/8 1/4 TEE HANDLE HEXAGON SHOULDER 3/8 1/2 LEVER HANDLE ROUND SHOULDER 1/8 1/4 LEVER HANDLE HEXAGON SHOULDER 3/8 1/2 Wt./100 (lbs.) 12.8 13.0 17.0 20.0 13.1 14.2 17.0 22.9 lever handle hexagon shoulder Customer Service 1-704-841-6000 53 Plumbing and Heating Air & Drain Cocks 41 Series Air Cocks (for air use only) An economical way to shut off air lines. Nut bottom available for pressures to 200 psig with 1/8" port. Many handle configurations. Spring bottom with 5/32" port standard. • Spring bottom cocks tested at 80 psig air • Available in satin or polished brass or satin chrome Type Standard Nut Bottom tee handle double male thread lever handle double male thread Satin Brass -01 -04 Polished Brass -05 -08 No. 41-180 41-190 41-203 41-210 41-220 41-230 41-240 41-251 tee handle bibb nose lever handle bibb nose 41-260 41-270 41-280 41-330 41-290 41-300 41-310 41-320 tee handle double female tee handle male & female 41-370 41-380 41-390 41-391 41-400 41-410 41-420 41-421 41-430 41-440 41-450 41-451 lever handle double female lever handle male & female 41-460 41-470 41-480 41-481 41-490 41-500 41-510 41-511 54 tee handle male & female hex shoulder Customer Service 1-704-841-6000 • Maximum temperature is 500˚F Satin Chrome -17 -20 Wt./100 Size(in.) (lbs.) TEE HANDLE DOUBLE MALE THREAD 1/8 14.0 1/4 17.9 3/8 20.0 1/2 33.1 LEVER HANDLE DOUBLE MALE THREAD 1/8 14.0 1/4 18.5 3/8 19.1 1/2 31.3 TEE HANDLE BIBB NOSE 1/8 14.5 1/4 16.3 3/8 33.3 1/2 36.0 LEVER HANDLE BIBB NOSE 1/8 16.5 1/4 15.0 3/8 32.1 1/2 36.0 TEE HANDLE DOUBLE FEMALE 1/8 13.0 1/4 14.0 3/8 26.0 1/2 27.0 TEE HANDLE MALE & FEMALE 1/8 13.0 1/4 14.0 3/8 21.0 1/2 26.0 LEVER HANDLE DOUBLE FEMALE 1/8 14.8 1/4 13.0 3/8 23.0 1/2 27.0 LEVER HANDLE MALE & FEMALE 1/8 15.2 1/4 15.0 3/8 23.0 1/2 27.0 TEE HANDLE MALE & FEMALE HEX SHOULDER 1/8 17.0 1/4 15.0 3/8 23.0 1/2 25.0 Plumbing and Heating Air & Drain Cocks Air Cocks (for air use only) 41 Series An economical way to shut off air lines. Nut bottom available for pressures to 200 psig with 1/8" port. Many handle configurations. Spring bottom with 5/32" port standard. • Spring bottom cocks tested at 80 psig air • Available in satin or polished brass or satin chrome Type Standard Nut Bottom Satin Brass -01 -04 • Maximum temperature is 500˚F Polished Brass -05 -08 Satin Chrome -17 -20 Wt./100 Size(in.) (lbs.) LEVER HANDLE MALE & FEMALE HEX SHOULDER 1/8 14.0 41-520 41-530 1/4 15.0 41-540 3/8 22.1 41-541 1/2 27.0 TEE HANDLE DOUBLE FEMALE HEX SHOULDER 1/8 17.0 41-550 41-560 1/4 17.0 41-570 3/8 25.0 41-571 1/2 28.3 LEVER HANDLE DOUBLE FEMALE HEX SHOULDER 1/8 15.0 41-580 41-590 1/4 18.2 41-600 3/8 24.0 41-601 1/2 28.8 TEE HANDLE STRAIGHT NOSE HEX SHOULDER 1/8 15.7 41-630 41-640 1/4 15.0 LEVER HANDLE STRAIGHT NOSE HEX SHOULDER 1/8 14.0 41-650 41-660 1/4 15.0 No. lever handle male & female hex shoulder tee handle double female hex shoulder lever handle double female hex shoulder tee handle straight nose hex shoulder lever handle straight nose hex shoulder 41 Heavy & Extra Heavy Pattern Air Cocks Heavy and extra heavy patterns for stronger applications. • Rated for air pressure up to 250 psig with nut version • Extra heavy pattern rated for 150 WSP - nut bottom only Type Standard Nut Bottom Satin Brass -01 -04 Polished Brass 05 08 Satin Chrome 17 20 Wt./100 Size(in.) (lbs.) HEAVY PATTERN TEE HANDLE DOUBLE FEMALE 1/4 28.0 41-102 LEVER HANDLE DOUBLE FEMALE 1/4 27.0 41-103 EXTRA HEAVY PATTERN TEE HANDLE DOUBLE FEMALE 1/8 32.0 41-200 41-202 1/4 32.0 TEE HANDLE DOUBLE FEMALE HEXAGON SHOULDER 1/4 38.0 41-222 TEE HANDLE MALE AND FEMALE 1/4 20.0 41-250 No. Customer Service 1-704-841-6000 55 Plumbing and Heating Air & Drain Cocks 42-100 Series Drain Cocks Rough brass construction; rated for 25 psig. • Sizes: 1/8", 1/4", 3/8" and 1/2" Type Standard Nut Bottom No. 42-101 42-102 42-103 42-104 Satin Brass -01 -04 Polished Brass 05 08 Size(in.) 1/8 1/4 3/8 1/2 Satin Chrome 17 20 Orifice(in.) 3/16 1/4 3/8 3/8 Wt./100 (lbs) 20.4 15.0 35.0 38.0 * see above suffix key 43-100 Series Steam Gauge Cocks Female fitting with male union for easy installation. • Rated 100 WSP for standard bottom, 150 WSP for nut version • Available in polished brass or satin brass finish No. 43-101 Size(in.) 1/4 Wt./100 (lbs.) 45.0 Designate (-05) suffix for polished brass; (-01) suffix for satin brass. 44-100 Series Hose End Cocks Interior diameter hose sizes: 3/8" to 7/16" • 3/16" port; rated 25 psig • Available in polished brass or satin brass finish No. 44-101 44-102 44-103 44-104 Size(in.) 1/8 1/4 3/8 1/2 Wt./100 (lbs.) 19.0 22.0 23.0 25.0 Designate (-05) suffix for polished brass; (-01) suffix for satin brass. 56 Customer Service 1-704-841-6000 Plumbing and Heating Bar Stock Needle Valves 60 Series Bar Stock Needle Valves Built from a variety of materials, these needle valves are rated to 10,000 psig for cold, non-shock service and temperatures to 550°F. Will back-seat when fully opened to relieve pressure on packing, eliminate stem blow out problems and prevent leakage. Integral metal-to-metal seat and disc design; available with lock bonnet or ready for panel mounting. High-grade packing standard; carbon graphite packing standard; PTFE packing standard for 316 SS valves. Female x female NPT standard. • 60-100: Carbon steel, F x F, M x F, 1/8" to 1" • 60-400: 416 SS, F x F No. FEMALE X FEMALE 60-100/60-400/60-700 60-101/60-401/60-701 60-102/60-402/60-702 60-103/60-403/60-703 60-104/60-404/60-704 60-105/60-405/60-705 60-900 60-901 60-902 60-903 60-904 60-905 Socket Weld • 60-700: 316 SS, F x F, M x F, 1/8" to 1" • 60-900: Brass, F x F, 1/8" to 1/2" Size(in.) Orifice Dimensions (in.) A B C D E Cv Wt./100 (lbs.) 1/8 1/4 3/8 1/2 3/4 1 1/8 1/4 3/8 1/2 3/4 1 .125 .187 .250 .312 .437 .562 .125 .187 .250 .312 .437 .562 3.81 3.81 3.81 3.81 5.43 6.00 3.81 3.81 3.81 3.81 5.43 6.00 1.37 1.37 1.37 1.50 1.93 2.12 1.37 1.37 1.37 1.50 1.93 2.12 2.25 2.25 2.25 2.75 3.18 3.62 2.25 2.25 2.25 2.75 3.18 3.62 1.12 1.12 1.12 1.37 1.59 1.81 1.12 1.12 1.12 1.37 1.59 1.81 .68 .68 .68 .75 .96 1.06 .68 .68 .68 .75 .96 1.06 .43 .43 .74 1.36 2.64 3.60 .43 .43 .74 1.36 2.64 3.60 123 123 119 164 334 424 136 136 131 181 369 469 MALE X FEMALE 60-111/60-711 60-112/60-712 60-113/60-713 1/4 1/8 1/2 .187 .250 .312 3.81 3.81 3.81 1.37 1.37 1.50 2.25 2.25 2.75 1.12 1.12 1.37 .68 .68 .75 .43 .74 1.36 108 104 141 ANGLE VALVES 60-200/60-500/60-800 60-201/60-501/60-801 60-202/60-502/60-802 60-203/60-503/60-803 60-204/60-504/60-804 60-205/60-505/60-805 1/8 1/4 3/8 1/2 3/4 1 .125 .187 .250 .312 .437 .562 3.18 3.31 3.31 3.31 4.50 5.06 1.00 .87 1.00 1.50 1.50 2.00 1.25 1.50 1.59 2.00 2.50 2.93 .81 1.03 1.06 1.37 1.62 1.93 .50 .62 .62 .75 1.00 1.25 .39 .43 .84 1.36 2.64 3.90 60 80 90 120 320 500 F .424 .559 .694 .859 1.069 1.334 G .37 .37 .37 .37 .50 .50 No. 60-120/60-420/60-720 60-121/60-421/60-721 60-122/60-422/60-722 60-123/60-423/60-723 60-124/60-424/60-724 60-125/60-425/60-725 Dimensions (in.) Size(in.) Orifice A B C D E 1/8 .125 3.81 1.37 2.25 1.12 .68 1/4 .187 3.81 1.37 2.25 1.12 .68 3/8 .250 3.81 1.37 2.25 1.12 .68 1/2 .312 3.81 1.50 2.75 1.37 .75 3/4 .437 5.43 1.93 3.18 1.59 .96 1 .562 6.00 2.12 3.62 1.81 1.06 Customer Service 1-704-841-6000 Cv .43 .43 .74 1.36 2.64 3.60 Wt./100 (lbs.) 123 123 119 164 334 424 57 Plumbing and Heating Miscellaneous Products 3T-WMV Series Washing Machine Control Valve Single lever control of hot, cold water supplies; helps extend hose life and reduce risk of bursting by keeping pressure within piping. Models to fit most machine installations. • Precision twin-ball design for positive shut-off • Model 3S-WMV – 1/2" sweat with swivel copper 90˚ elbow for easy retrofit • Model 3T-WMV – 1/2" NPT or 1/2” sweat connection for through-wall/concealed piping • Model 3T-WMV-X – 1/2" NPSM or 1/2” sweat connection extended for wall connection boxes • 3/16" port; rated 25 psig Model No. 3S-WMV 3T-WMV 3T-WMVX 14-290 Series Part No. 35-303-01 35-303-02 35-303-03 Wt./100 (lbs.) 116 133 177 Vacuum Relief Valves For protection of bulk handling vacuum systems and light gauge storage tanks. • One-piece body, bronze construction B No. 14-295 14-296 14-297 A C Size(in.) 2x2 2-1/2 x 2-1/2 3x3 • Available with settings of 6 to 30 inches mercury Dimensions B(in.) 6-1/2 7-5/8 8-3/4 A(in.) 3 3-1/2 4-1/8 C(in.) 3-1/8 3-1/2 3-7/8 D(in.) 2-7/16 2-21/32 3-1/8 Wt./Ea. (lbs) 8.4 13.0 17.0 D Capacities SCFM Air at 10% Accumulation 27-400 Series Set Inches Mercury. 6 8 10 12 13 16 18 20 25 30 Key -V6 -V8 -WO -W2 -W3 -W6 -W8 -V20 -V25 -V30 2" 14-295 355 395 415 426 430 430 430 430 430 430 2-1/2" 14-296 539 600 635 649 653 653 653 653 653 653 3" 14-297 780 865 915 939 943 943 943 943 943 943 Steam Gauge Siphon 90° and 180° configurations, made from 1/4" heavy gauge seamless brass tubing. • Brass, satin chrome and bright dip finishes • 27-401 is 180° loop, 27-402 is 90° loop type. • Service rating: 250 psig saturated steam, 400 psig at 100°F No. 27-401 27-402 Size (in.) 1/4 1/4 Wt./100 (lbs.) 44.0 40.0 Brass. 01 SUFFIX NUMBER* Satin Chrome 03 Bright Dip 04 *Specify finish by adding the above two-digit suffix after product number. 58 Customer Service 1-704-841-6000 Plumbing and Heating Miscellaneous Products 28-400 & 28-600 Series Fusible Plugs (outside type fireside) Model 28-400 conforms to ASME standards, with maximum pressure of 250 lbs. 28-600 offers maximum pressure of 50 lbs. • Installed below boiler’s water level • Fusible plugs are installed between the fireside of either the plate, flue or tube of the boiler and below the water level 35-200 Series • 28-400 models are manufactured to conform to ASME standards and meet U.S. Coast Guard requirements • Fire-activated fusible plugs are filled with pure tin and feature a melting point between 445°F and 450°F No. 28-402-01 28-403-01 28-602-01 28-603-01 Size(in.) 1/2 3/4 1/2 3/4 Wt./100 (lbs.) 24.0 38.0 16.0 30.0 No. 35-201-10 35-202-10 Size(in.) 1/2 3/4 Wt./100 (lbs.) 58.3 57.0 Compression Bibb Faucet Features heavy pattern with large opening. • Rough brass finish; sizes 1/2" and 3/4" 35-300 Series Ball Valve Bibb Faucet Features heavy pattern with large opening. • Rough brass finish; sizes 1/2" and 3/4" No. 35-301-03 35-302-03 39-100 Series Size(in.) Inlet 1/2 1/2 sweat/threaded connector 3/4 3/4 thread connector Outlet .75-11.5 NHR hose .75-11.5 NHR hose Wt./100 (lbs.) 38.4 44.5 Hoist Control Valve Designed and manufactured to provide years of trouble-free service. Locking and non-locking models; steel lever pins and cam. 100% tested. • 1/2" FNPT connections • Bronze body • Stainless steel springs and screens • Rust-proof, cam action lever • Large volume • Compact No. 39-101-01 39-102-01 Customer Service 1-704-841-6000 Model Non-Locking Locking Wt./100 (lbs.) 202.0 202.0 59 Plumbing and Heating Miscellaneous Products 45-100 Series Oil Tank Valves Designed to assure trouble-free operation and compact shut-off. • For use with fuel oil, water, other liquids; not with steam • Operating pressure 10 psi 45-201 & 45-301 Series • Temp. range -20˚F to 250˚F No. 45-101-01 45-102-01 45-103-01 45-104-01 NPT Pipe x Flared Tube 1/2 x 3/8 1/2 x 1/2 3/4 x 3/8 3/4 x 1/2 Wt./100 (lbs.) 27.6 29.9 32.0 33.1 No. 45-105-01 45-106-01 45-107-01 45-108-01 NPT Pipe x Comp. w/Nut Sleeve 1/2 x 3/8 1/2 x 1/2 3/4 x 3/8 3/4 x 1/2 Wt./100 (lbs.) 27.0 30.0 31.7 32.0 Barrel Faucets Heavy duty rust-proof handle can be locked in closed position. • Standard 3/4" tapered pipe thread for drum, barrel openings No. 45-201-01 45-301-01 • Rust proof steel spring • Heavy-duty cast bronze body with wrench flats Size(in.) 3/4 3/4 Seat Brass Brass Wt./100 (lbs.) 85.0 108.0 Materials Brass PTFE 45-301-01 Meets Factory Mutual Approval Standard NO. 6031 For Self Closing Drum Faucets 78-124 & 78-125 Series 5-Port Tank Selector Unique ball design allows for higher flow capacities. Five port construction allows access to four tanks using only one valve. • Five NPT connections. • Bronze ball valve with stainless steel Lever and Nut. • PTFE seats and RPTFE stem packing. • Stem packing adjustable for wear • Non-lubricated No. 78-124-01 78-125-01A 60 Size 1/2 3/4 Customer Service 1-704-841-6000 A 0.50 0.75 • 50 psig pressure rating • Operation: four selected inlets feed one common outlet • Pointer on handle indicates the selected inlet • Easy mounting design Dimensions (in.) B C D 1.26 2.52 2.27 1.56 3.12 2.93 E 3.53 3.87 F 1.12 1.53 G 10-24 1/4-20 H 1.40 1.98 Wt./100 (lbs.) 106 264 Plumbing and Heating Miscellaneous Products IBV-125 Series Apollo International Cast Iron Full Port Class 125 Flanged Ball Valve The Conbraco IBV-125 Series cast iron ball valve meets MSS SP-72, ANSI B16.10 and federal WW-V-35 performance standards. They can be used to replace any IBBM gate valve or plug valve. With their full port design, these valves assure an unobstructed, turbulence-free flow that gate and butterfly valves can’t match. Low profile handle for easy installation in tight areas. Sizes from 2" to 10". Rated 125 WSP, 200 WOG, with a maximum operating temperature of 350˚F. • • • • Gear operator standard 8" and 10" Full port design offers superior flow rate No bronze seat rings, disc rings or stems to wear out Quarter-turn offers instant, positive shutoff with zero leakage • Stainless steel ball resists corrosion • Handle indicates valve operation status • • • • • • Large actuator mounting pad standard Optional locking handles available Blowout-proof stainless steel stem PTFE seats and packing, not Nitrile or EPDM Opens and closes easily, without cheater bar For more technical information, request #PHBRIRBV brochure IBVE-125 Series Apollo International Epoxy Coated Cast Iron Full Port Class 125 Flanged Ball Valve BVE-125 Series valves have all the design and construction features of the IBV-125 plus an FDA-approved, heat-fused epoxy coating making them ideal for corrosive water service as well as food contact applications. Maximum operating temperature: 140˚F. • For additional technical information, request #PHBRIRBV brochure IBVD-125 Series Apollo International Ductile Iron Full Port Class 125 Flanged Ball Valve BVD-125 series valves have the same design and construction features of the IBV-125 series but in ductile iron. Same dimensional data as IBV/IBVE series. Available in sizes 2" through 6". Model No. IBV No. 6P-208-01 6P-209-01 6P-200-01 6P-20A-01 6P-20C-01 6P-20E-01 6P-20G-01 C D IBVE No. 6Q-208-01 6Q-209-01 6Q-200-01 6Q-20A-01 6Q-20C-01 6Q-20E-01 - IBVD No. 6R-208-01 6R-209-01 6R-200-01 6R-20A-01 6R-20C-01 - Dimensions (in.) Size A B (in.) (in.) (in.) 2 7 6 2-1/2 7.5 7 3 8 7.5 4 9 9 6 10.5 11 8* 11.5 13.5 10* 13 16 C (in.) 9 16 16 19.7 26 - D Wt./100 (in.) (lbs.) 3 22 3.7 34 4 38 4.8 58 7.2 118 9.24 345 11.81 440 B A 141-143 Series General Purpose/Economy Butterfly Valves Apollo 141/143 Series valves form a lineup of economical butterfly valves ideal for use in industrial and HVAC/mechanical markets. 141 Series is a wafer style valve (2" - 24"); 143 Series is a companion lug (2" - 24"). Both are rated at 200 PSI (2''-12'') and 150 PSI (14''-24'') bubble-tight shut-off between flanges. These valves are designed for reliable performance in hot and cold water applications, treated or untreated, on-off or throttling, control isolation, flow balance or diversion tasks. Valves are 100 percent factory tested in both operational directions. They feature an extended neck length to provide a minimum 2” clearance between valve top plate and pipe flange. 141/143 Series meet MSS SP-67 and API 609 specifications. Customer Service 1-704-841-6000 61 Plumbing and Heating Miscellaneous Products 64 Series Apollo International Full Port Brass Ball Valves Economy full-port forged ball valve with maximum flow; ideal choice for all plumbing applications. Lever handle is standard on all sizes. • • • • Sizes from 1/4" to 4" Threaded (-100) and solder end (-200) connections Pressure rated to 600 psig WOG; 150 psig steam Temperatures to 366˚F (185˚C) • • • • Blowout-proof stem Chrome-plated brass ball Secondary O-ring stem seal PTFE seats, thrust bearing and stem packing 64-100 Size(in.) 1/4 NPT 3/8 NPT 1/2 NPT 3/4 NPT 1 NPT 1-1/4 NPT 1-1/2 NPT 2 NPT 2-1/2 NPT 3 NPT 4 NPT No. 64-101-01 64-102-01 64-103-01 64-104-01 64-105-01 64-106-01 64-107-01 64-108-01 64-109-01 64-100-01 64-10A-01 A(in.) 0.39 0.39 0.59 0.78 0.98 1.25 1.57 1.96 2.56 3.15 3.94 Dimensions B(in.) 2.02 2.02 2.44 2.71 3.07 3.42 3.89 4.33 5.59 6.45 7.60 C(in.) 1.75 1.75 1.88 2.28 2.44 3.07 3.34 3.79 5.02 5.45 6.34 D(in.) 3.85 3.85 3.85 4.80 4.80 6.02 6.02 6.37 8.07 8.07 10.23 Cv 6 7 19 34 50 104 268 309 629 1018 1622 64-200 Size(in.) 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4 No. 64-203-01 64-204-01 64-205-01 64-206-01 64-207-01 64-208-01 64-209-01 64-200-01 64-20A-01 A(in.) 0.59 0.78 0.98 1.25 1.57 1.96 2.56 3.15 4.13 Dimensions B(in.) 2.53 2.99 3.58 4.09 4.56 5.43 6.93 8.09 10.25 C(in.) 1.88 2.28 2.44 3.07 3.34 3.79 5.02 5.45 6.34 D(in.) 3.85 4.80 4.80 6.02 6.02 6.37 8.07 8.07 10.23 Cv 19 34 50 104 268 309 629 1018 1622 Optional Kits Valve Size 1/4", 3/8" and 1/2" 3/4" and 1" 1-1/4" and 1-1/2" 2" 2-1/2" and 3" 4'' Stem Extensions 78-1501-01 78-1502-01 78-1503-01 78-1504-01 78-1505-01 - Balancing Stops 78-1506-01 78-1507-01 78-1508-01 78-1509-01 78-1510-01 - Locking Handles 78-1659-01 78-1660-01 78-1661-01 78-1662-01 - Lever Handles 78-1646-01* 78-1647-01 78-1648-01 78-1649-01 78-1650-01 78-1651-01 Note: Specify -07 suffix for “T” handle, ie. 64-105-07. Available with threaded models only in 1/4”-1” sizes. * Lever handle available with 1/2" only 95A Series Apollo International Full Port Brass Ball Valve With Stop & Waste Threaded 95A-303-01 95A-304-01 95A-305-01 62 Customer Service 1-704-841-6000 Sweat 95A-403-01 95A-404-01 95A-405-01 Size(in.) 1/2 3/4 1 Plumbing and Heating Terms and Condition of Sale Payment: 2% 10th prox. Net 30 days. All prices F.O.B. Matthews, N.C., or Pageland, S.C., with freight allowed on shipments of 750 pounds or $4,000 net and over to all shipping points within the United States excluding Alaska and Hawaii. No freight allowed on Air Freight or Parcel Post shipments. Claims for shortages must be made within 10 days of receipt of material. Our responsibility ends when a receipt is furnished us by the carrier. No Invoice Rendered For Less Than $50.00. No freight will be allowed on Air Freight, Air Express, Parcel Post or U.P.S. shipments.Other Conbraco Products may be combined to make sufficient weight for full freight allowance. Phone order quoted prices are subject to correction. Prices and designs are subject to change without notice. Orders for material or special design or specification are made to customer’s order and are not subject to cancellation or return. Goods returned to us will not be accepted unless a full explanation has been made and our written authorized permission obtained. All goods returned – if accepted – will be credited at invoice price, less 30% for service and rehandling charges, plus shipping expenses.We reserve the right to adjust orders to box quantities. Warranty and Limitations of Liability Conbraco Industries, Inc. warrants, to its initial purchaser only, that its products which are delivered to this initial purchaser will be of the kind described in the order or price list and will be free of defects in workmanship or material for a period of one year from the date of delivery to you, our initial purchaser. Should any failure to conform to this warranty appear within one year after the date of the initial delivery to our initial purchaser, Conbraco will, upon written notification thereof and substantiation that the goods have been stored, installed, maintained and operated in accordance with Conbraco's recommendations and standard industry practice, correct such defects by suitable repair or replacement at Conbraco's own expense. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHER WARRANTY, WHETHER EXPRESS OR IMPLIED, EXCEPT THE WARRANTY OF TITLE AND AGAINST PATENT INFRINGEMENT. Correction of non-conformities, in the manner and for the period of time provided above, shall constitute fulfillment of all liabilities of Conbraco to our initial purchaser, with respect to the goods, whether based on contract, negligence, strict tort or otherwise. It is the intention of Conbraco Industries, Inc. that no warranty of any kind, whether express or implied shall pass through our initial purchaser to any other person or corporation. LIMITATION OF LIABILITY: Conbraco Industries, Inc. SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR SPECIAL OR CONSEQUENTIAL DAMAGES SUCH AS, BUT NOT LIMITED TO, DAMAGE TO LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF PROFITS OR REVENUE, COST OF CAPITAL, COST OF PURCHASED OR REPLACEMENT GOODS, OR CLAIMS OF CUSTOMERS OF OUR INITIAL PURCHASER. THE REMEDIES OF OUR INITIAL PURCHASER, AND ALL OTHERS, SET FORTH HEREIN, ARE EXCLUSIVE, AND THE LIABILITY OF CONBRACO WITH RESPECT TO SAME SHALL NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE CONBRACO GOODS UPON WHICH SUCH LIABILITY IS BASED. Customer Service 1-704-841-6000 63 Sales Department P.O. Box 247 Matthews, NC 28106 Phone: 704-841-6000 Fax: 704-841-6021 International Sales Department P.O. Box 247 Matthews, NC 28106 Phone: 704-841-6000 Fax: 704-841-6020 Customer Service Department P.O. Box 247 Matthews, NC 28106 Phone: 704-841-6000 Fax: 704-841-6020 Fax Florida [email protected] 813-901-0988 Valves & Fittings, Inc. Georgia/Alabama/Tennessee-East [email protected] 770-483-3057 770-483-3110 Pro Marketing, Inc. North Carolina/South Carolina [email protected] 864-578-4334 864-578-4889 Mid South Marketing Virginia/Maryland/Washington, D.C./WV-East [email protected] 804-749-8712 804-749-8717 Southern Marketing Group MS/TN-West/AR/Bowie Cty.-TX [email protected] 901-547-0042 901-547-0035 AVC Mechanical Oklahoma/Texas-North [email protected] 817-649-2229 817-649-2225 Knox & Associates, Inc. Texas-South/Louisiana [email protected] 713-462-7766 713-690-6228 HEBCO, Inc. Kansas/Missouri-West [email protected] 913-491-0797 913-491-5126 New Tech Marketing, Inc. IL/WI-East/IN-North/MI-Upper Peninsula/IA-River Counties [email protected] 630-378-4300 630-378-0343 New Tech Marketing, Inc. Eastern Missouri/Southern Illinois [email protected] 618-394-0329 618-394-0427 L.J. Whitfill & Associates, Inc. Kentucky/Indiana-South/Ohio-South [email protected] 502-459-4545 502-459-9944 V.E. Sales Co., Inc. Michigan (Except Upper Peninsula) [email protected] 586-774-7760 586-774-1490 Northstar Valve & Fitting, Inc. Minnesota/North & South Dakota/Wisconsin-West [email protected] 952-937-0108 952-937-0803 Willco, Inc. Nebraska/Iowa (Except River Counties) [email protected] 402-573-7000 402-573-7371 Morrissey Associates, Inc. Ohio-North/Pennsylvania-West/West Virginia-West [email protected] 330-538-0406 330-538-0410 Aqua Products Group California-North [email protected] 925-473-1288 925-473-1798 Specification Sales California-South [email protected] 909-594-7088 909-594-2798 Marshall-Rodeno Associated CO/WY/MT/ID-SE/UT/NV-NE/NM/El Paso-TX [email protected] 303-575-6701 303-575-6706 J.P. Harris & Associates, Inc. Washington/Oregon/Idaho-North West/Alaska [email protected] 360-944-8457 360-944-8459 Layden Valve Sales & Solutions Hawaii [email protected] 808-456-3331 808-455-1064 [email protected] 480-813-1313 480-813-2286 Las Vegas/Clark County/Nevada [email protected] 702-368-2561 702-368-1784 Urell, Inc. Massachusetts/New England States [email protected] 617-923-9500 617-926-9414 Pence & Associates New York-Upstate/New York-West [email protected] 315-423-0066 315-423-0290 Continuous Sales Corporation New York-East/New Jersey-North [email protected] 516-248-5177 516-248-5187 J.A. Layden Co. Pennsylvania-East/Delaware/New Jersey-South [email protected] 610-353-2311 610-359-1299 Keith Engle & Associates OEM accounts [email protected] 610-827-9560 610-827-9561 Conbraco Industries, Canada 160 Pennsylvania Ave., Unit 3, Concord, Ontario L4K 4A9 [email protected] 905-761-6161 905-761-6666 Barclay Sales Ltd. British Columbia [email protected] 604-945-1010 604-945-3030 Mechanical Systems 2000, Inc. Alberta-South [email protected] 403-291-1244 403-219-0686 Dynamic Agencies, Ltd. Saskatchewan [email protected] 306-343-1901 306-343-1901 Tom Beggs Agencies Ltd. Manitoba/NW Ontario [email protected] 204-953-1900 204-774-6915 Task Controls, Inc. Ontario [email protected] 416-291-3004 416-754-3481 Agences J. Pierre Sylvain, Inc. Quebec [email protected] 450-655-9588 450-641-2737 Kern Industries, Ltd. Alberta-North [email protected] 780-451-2056 780-454-6687 J. Levandier Sales, Inc. Nova Scotia, New Brunswick, Prince Edward Island [email protected] 506-858-1615 506-858-1084 Smith Agencies Western Region Northeast Region Canada Int’l./ Puerto Rico Phone B. Lynch & Assoc. Midwestern Region Southern Region Southeast Region E/Mail Address Southwestern Mechnical Sales Co. Arizona/Nevada-SW 813-901-8403 Newfoundland [email protected] 709-364-8856 709-747-9414 Key to the North Sales Agency, Inc. Ontario-North [email protected] 705-566-0148 Pelco Sales Eastern-Ontario/Ottawa [email protected] 613-839-0115 Rafael Rodriguez Barril, Inc. Puerto Rico Conbraco Industries, Int’l. (Europe) Manchester, England 613-839-0114 [email protected] 787-759-8680 [email protected] +44-161-908-2340 787-759-8986 +44-161-908-2359 For Representatives And Distributors In Your International Area Please Contact The Closest Conbraco Industries International Office Conway, SC • Matthews, NC • Pageland, SC • Customer Service 1-704-841-6000 • www.conbraco.com PHCA9000 Printed in USA Copyright 01/02
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement