®
VERSAFILLER®
Model PWSBF (retro fit) and
P*SBF Family of Drinking
Fountains/VersaFiller combo
Installation Instructions
The VersaFiller is an extension of the Aqua Pointe® product line that mounts
directly above Versacooler® I and II products. No additional electrical
connections are required.
If installed onto a refrigerated cooler, then chilled water can be dispensed
through the VersaFiller. Otherwise, room temperature water will be dispensed.
The VersaFiller is shipped partially assembled.
On the combo units, the cooler is plumbed and ready to attach to the
VersaFiller.
When completed, the finished assembly will look like this:
OR
Section 1: Getting Started
What’s Included:
(Top cap)
VersaFiller Sports
Bottle Filler- (with
wrapper, alcove
and top cap
installed onto the
frame)
Drip tray
Gasket
Anti splash grate
Anti Splash
grate screws (2)
Quick connect
tee fitting
38” of ¼ OD
plastic tubing
with 19” of
sponge tubing
insulation
Installation
instructions
Tools required:
3/8 drill bit that will drill through SS top
Electric drill
Small tubing cutter for copper tube
1/4 “ nut driver
# 2 Phillips screw driver
#15 torx bit driver
Snap bushing
Section 2: Rough In Drawing
Oasis PWSBF: Versacooler® II Models PAC, P8AC with VersaFiller
Section 2: Rough In Drawing
Oasis PWSBF: Versacooler® II Split Level Models with VersaFiller
* On split level models, the VersaFiller must be mounted
on the low unit in order to meet ADA guidelines.
Section 3: Installation
Note: Proceed to Sect 3B Step 5 if the cooler is
purchased “VersaFiller ready”.
A: Drilling hole in the top for water line connection.
1.
Disconnect power by UNPLUGGING unit. It might be necessary to
remove the front panel to get access to the power.
2.
Turn OFF water supply to the unit. It might be necessary to remove the
front panel to access the water stop valve.
3.
Place hole template onto cooler top so it is aligned with the left side of
unit and wall. SEE NEXT PAGE FOR TEMPLATE
4.
Mark hole location
5.
Remove top from unit.
Mark hole location.
Template
Remove top from cooler by
removing six #15 torx head screws
on sides of top.
6.
Using a 3/8 drill bit, drill a hole through top.
7.
Install snap bushing into hole to protect tubing from being cut.
Install bushing
Drill
ALIGN THIS EDGE WITH LEFT EDGE OF COOLER TOP
Mark this center point on the
top. Remove the top from the
cooler. Then drill a 3/8 hole
through the top at the marked
center point.
USE THIS TEMPLATE TO MARK THE
HOLE LOCATION ON COOLER TOP
2-1/8”
from
back
PLACE THIS EDGE AGAINST WALL
3-1/4”
from
side
Section 3: Installation
B: Connecting the water line
If the cooling tank is non-pressurized, then go to the “Pressurizing the
cooling tank” addendum section. Otherwise, proceed to step 1 below.
Non-pressurized units are single units made since December of 2009.
Refer to the schematic below to identify the system that you have.
Water
valve/
regulator
NONPRESSURIZED
COOLING TANK
1.
Supply
Water
Cooling
tank
Supply
Water
Cooling
tank
Water
valve/
regulator
PRESSURIZED
COOLING
TANK
With the cooler top removed, find the tube going from the cooling
tank outlet to the valve. The TEE fitting (supplied) will need to
connect between the cooling tank and valve.
Outlet Tube (insulated plastic)
Valve
P8AC family
Outlet Tube (insulated copper)
Valve
P8AM family
Section 3: Installation: For the P8AC Version: Versacooler II
2.
Disconnect tubing from the
elbow on the valve.
3.
Using the 38” piece
of tubing provided,
cut 6” and install it
on the end of the
TEE. Install the
remaining tubing
onto the branch of
the TEE. Connect
the other end of the
TEE to the tank
outlet tubing (tube
that was
disconnected from
the elbow).
TEE
4.
32” tubing
6” tubing
Route the TEE and
tubing under the
waste drain and
connect the 6” length
to the water valve
elbow.
Go to Step 5 “Final steps for both product families:”
Water
valve
elbow
Section 3: Installation: For the P8AM Version: Versacooler I
Remove tar tape
2.
Remove tar tape from
the insulation on the
outlet tube.
3.
4.
Pull back insulation and cut
the copper tube with a
tubing cutter. Cut where
there is at least 1 inch of
straight tubing on each side
of the cut.
Install TEE fitting by
connecting the copper
tubing to each end. Then
install the 32” piece of
plastic tubing to the TEE
branch.
32” plastic
tubing
(supplied)
Section 3: Installation: Final steps for both product families:
5. Feed tubing up through the top and attach the
top to the cooler.
TIP: For the P8AM, it is easier to
connect the outlet tube to the bubbler if
the front nose is removed.
C: Mounting the frame to the wall
1. Place rubber gasket on top of the cooler so it is centered left/right
and against the wall.
Section 3: Installation
2. Set the wall frame onto the gasket. Center it left/right and push it against
the wall and mark hole locations for wall fasteners. The gasket will set the
frame at the proper height.
Use mounting slots that
will provide the proper
securing location.
Make sure to pull
the plastic tubing
up through the
hole in the frame.
3. Secure frame to the wall with fasteners (not provided). Pull plastic
tubing up through the hole in the frame.
4. Slide sponge tubing insulation over water line. Connect the tubing to
the INLET elbow on the back of the VersaFiller assembly.
Connect tube
to elbow on
the valve
Plastic tubing
Sponge tubing
insulation
Rear view of VersaFiller
Section 3: Installation
5. Set the VersaFiller cabinet into place. MAKE SURE the cabinet fits
into the groove in the rubber gasket on both sides and front of the
wrapper.
VersaFiller
cabinet
Groove in the gasket
6. Attach VersaFiller assembly and top cap to the frame using the six
(6) torx screws.
Torx screws
Section 3: Installation
7. Install the drip tray and anti-splash grate into the alcove area
and secure with the two (2) stainless steel phillips head screws.
Anti-splash grate
screws (provided)
Anti-splash grate
Drip tray
8. Turn ON water supply and check for leaks. Press the activation button
and release any trapped air from the system. Plug in the power cord and
replace the front panel IF it was removed earlier.
Press
INSTALLATION COMPLETE
Addendum Section: Pressurizing Cooling Tank
The water should
already be turned OFF
and the power
disconnected.
Unit as it appears with
top removed
STEP 1
Unplug un-insulated water
line from water valve inlet
(JG elbow located left side
of water valve facing the
front of the cooler). Set
tubing aside (careful to not
contaminate water contact
end).
STEP 2
Unplug tubing from JG
elbow leading to
cooling tank inlet.
STEP 3
Plug un-insulated tubing that
was removed in step 1 into
JG elbow leading to the
cooling tank from step 2.
STEP 4
Unplug tubing that is
connected to the
water valve outlet (JG
elbow located on the
right side of valve
facing the cooler).
STEP 5
Connect tubing
from step 4 to JG
elbow on the left
side of the valve.
Step 6
Unplug JG tubing
from the cooling
tank outlet. Do
not set it down.
Step 7
Using tubing
removed in step 6,
plug into JG elbow
on the right side of
the valve. (be sure
to rout the tubing
under existing
tubing installed in
step 4 as shown)
Step 8
Using tubing that is
connected to the JG
elbow left side of
valve (done in step
4), and plug the
other end to the JG
fitting at the top of
the cooling tank.
Return to Section 3 B
“Connecting the water line”
EXPLODED PARTS
BREAKDOWN
25
33
26
12
13
3
28
14
17
2
15
27
29
16
18
19
24
1
32
20
9
22
8
30
21
23
4
6
22
25
22
11
10
31
Accessories:
Vandal resistant screw kit: P/N 036704-001, includes torx bits and replacement screws for items 4 and 25.
5
7
22
Gasket, Sunroc/Haws : P/N 036689-101 (replaces item 10): KIT P/N 036752-001
Gasket, Elkay/Halsey Taylor P/N 036689-201 (replaces item 10 ): KIT P/N 036752-002
*Items highlighted in GRAY are available as service parts
1
2
3
4
036190-002
036691-001
036686-001
036049-002
ALCOVE, PWSBF
WRAPPER, PWSBF STN2
CAP, PWSBF
SCREW, FLAT HEAD TAPPING
17
18
19
20
028706-036
026670-007
028481-101
036479-001
WASHER/SPACER/GASKET-NON META
SCREW, HEX HD MACHINE
FTG, PP UNION ELBOW WHT
FILL TUBE ASSY
5
6
7
8
9
10
11
12
13
14
15
16
036688-001
036695-001
036697-001
036194-002
034649-001
036689-001
036191-002
035990-001
029967-002
A020957
036690-001
030176-002
TRAY, DRIP PWSBF
TRAY, GRILLE DRIP
DRIP TRAY BOTTOM CAP
BUTTON, PWSBF
SPRING, MSBF
GASKET, PWSBF
DRAIN, MSBF, SHORT
HOLDER, CARTRIDGE STEM CON
CARTRIDGE
NUT, RETAINING PLASTIC
BRACKET, VALVE PWSBF
PLUG, HOLE
21
22
23
24
25
26
27
28
29
30
31
32
33
036209-001
026642-003
031206-005
030152-046
031875-003
036687-001
027189-007
029199-103
030152-031
017681-008
036701-001
036702-001
036231-001-SP
BRACKET, FILL TUBE SUPPORT
SCREW, HEX HD TAPPING
INSERT, NAMEPLATE AQUAPOINTE
TUBE, PE CUT LENGTH WHI
SCREW, BUTTON HD TAPPING
FRAME, PWSBF
BUSHING, SNAP
FTG, PP UNION TEE WHITE
TUBE, PE CUT LENGTH WHI
INSULATION, SPONGE TUBING
DRIP TRAY ASSEMBLY-SERVICE
BUTTON ASSEMBLY, PWSBF-SERVICE
VALVE ASSEMBLY, PWSBF DISPENSE-SERVICE
P/N 030099-412
Date: 1/2011 Rev D
© 2011 Oasis International
Oasis, Aqua Pointe, Versacooler and VersaFiller are registered trademarks of
LVD Acquisition.
Haws is a registered trademark of HAWS Corporation.
Elkay and Halsey Taylor are registered trademarks owned or licensed by Elkay
Sales Inc. and/or its parent Elkay Manufacturing Company
Oasis International
222 East Campus View Blvd.
Columbus, OH 43235
614-861-1350
www.oasiscoolers.com