SNMP Web Pro
User’s Manual
Management Software for Uninterruptible Power Supply Systems
Table of Contents
1.
2.
3.
Overview ..........................................................................................................1
1.1 Introduction ...............................................................................................1
1.2 Features ....................................................................................................1
1.3 Overlook ....................................................................................................2
1.4 Installation and Connection..........................................................................2
1.5 Configuration .............................................................................................3
1.6 Monitoring .................................................................................................4
SNMP web pro GUI ............................................................................................7
Function Menu ..................................................................................................8
3.1 Information ................................................................................................8
3.2 UPS setting ................................................................................................9
3.3 Control .................................................................................................... 11
3.4. System configuration ................................................................................ 11
3.5. Log ......................................................................................................... 20
3.6. Help ........................................................................................................ 22
1. Overview
1.1
Introduction
This SNMP web pro can provide web server to monitor and manage multiple
UPSs in a networked environment including LAN and INTERNET. It can
detect temperature and humidity for the environment via connecting to EMD
(Environmental Monitoring Device). The same port is also applied for data
transmission. Simply connect to SMS modem for SMS sending with a RJ11 to
DB9 cable.
Integrated with Shutdown Wizard, it can not only prevent data loss from
power outage and safely shutdown systems, but also store programming
data and scheduled shut down the UPS. All UPS warning and fault event
records can be kept in SNMP web pro.
Integrated with ViewPower Pro software, it can monitor and remote access
all distributed devices with SNMP web pro card in a LAN or INTERNET. For the
detailed operations, please check user manual of ViewPower Pro.
1.2











Features
Open monitor via Web Browser.
Offer SNMP MIB to monitor UPS status.
Automatically detect and exchange 10M/100M Fast Ethernet.
Support wake-on-LAN function.
Supported protocol such as TCP/IP, UDP, SNMP, SMTP, SNTP, HTTP,
HTTPS, SSL, SSH, IPV4/IPV6, DHCP and so on.
Integrated with Shutdown Wizard, it can prevent data loss from power
outage and safely shut down systems.
Able to store event log more than 200,000 threads, including UPS
warnings, faults and EMD warnings, operation data logs from web users
or ViewPower pro users. It will be stored safely without loss even when
power failure occurs.
Support daily reports for event log and data log.
Scheduled UPS on/off and battery test.
Support EMD monitoring and SMS sending.
Equipped with real-time clock to record log with date and keep running
up to 7 days without power connected.
1
1.3
Overlook
Ethernet port (10/100Base-T)
Sensor port/data transmission port
Golden finger: connects to UPS slot
Ethernet port status LEDs
Jumper setting to restore default
setting
Ethernet port status LEDs:
100M LED (Green)
On
Off
Link status LED
Flash
(Yellow)
Off
Port is operating at 100Mbit/s
Current web bandwidth is 10Mbit/s
Link Active
Card is not connected to the network
Pin assignment for Jumper:
Pin #
Status
Pin 1 & Pin 2
Closed
Pin 2 & Pin 3
Closed
Description
Normal operation
After re-connecting utility, the IP
address of SNMP web card and
password will restore to default setting.
Default static IP address:
(192.168.102.230)
Default password: 12345678
NOTICE: After setting is restored to default, be sure to change the
jumper setting to connect Pin 1 and Pin 2 for normal operation.
1.4
Installation and Connection
Installation
If using SNMP web card, please follow below steps to install card first:
Step 1: Remove the cover of intelligent slot on the back panel of UPS
and retain the screws
Step 2: Slide the card into the open slot and secure with the screws from
step 1. (see chart 1-1)
2
Chart 1-1
Refer to chart 1-2 for connecting the SNMP web pro.
Step 3: Plug Ethernet cable to the Ethernet port (RJ-45) on the SNMP web
manager.
Step 4: Use one more Ethernet cable. Connect one end to the sensor port
on the SNMP web manager and the other end to the optional environmental
monitoring device.
Chart 1-2
1.5
Configuration
a) Please install SNMP web manager wizard in your PC. After software is
installed successfully, the Installer will leave a shortcut icon on your
desktop.
Chart 1-4
b) Enter specific IP address to search all SNMP devices in LAN. The
SNMP web manager is default applied static IP address as
192.168.102.230, default subnet mask as 255.255.255.0, and
default gateway as 192.168.102.1. Users can modify IP address or
apply DHCP mode through web server of SNMP web pro card, SSH
Client or SNMP Web Manager.
3
Chart 1-5
c) User can modify IP setting, online upgrade, password management,
and static trap address setting in SNMP Web Manager screen. It is
necessary to enter password for any medications. The default
password is 12345678.
Please check SNMP Web Manager User Manual for detailed configuration.
1.6
Monitoring
There are two ways to monitor:
a) Double click the selected device from the device list (refer to Chart
1-5) to open web page as Chart 1-6 a. Or simply enter https address
(http://192.168.107.234) in web browser to access web server directly.
Refer to Chart 1-6 b.
4
Chart 1-6 a
Chart 1-6 b
b)
Installed ViewPower Pro software to monitor SNMP web pro. Refer to
Chart 1-7.
Please check ViewPower Pro User Manual for detailed monitoring.
5
Chart 1-7
6
2. SNMP web pro GUI
SNMP web pro GUI includes function menu, login section and main screen.
Refer to Chart 2-1:
D
A
B
C
Chart 2-1
A .SNMP web pro GUI version
B .Function Menu
It offers complete tool-set for navigation and setting the GUI.
C .Main Screen
It will display information and/or control alternatives according to
function menu selected.
D. Login section
It shows user type for current login user. The default password for
administrator is “12345678”.
7
3. Function Menu
3.1
3.1.1.
Information
Status
Select Information >> Status. Refer to Chart 3-1. It’s shown real-time
monitored UPS data including input, output, UPS, battery information and
environmental information in table format.
Chart 3-1
3.1.2.
Basic information
Select Information>>Basic information. It includes UPS basic information,
battery information and UPS rated information. Refer to Chart 3-2.
8
Chart 3-2
3.2 UPS setting
3.2.1 Parameters setting
Some UPS functions can be set and changed via software. Parameter setting
includes backup time setting for programmable outlet (P1), battery number
setting, voltage and frequency range setting for bypass mode and voltage
range setting for ECO mode.
Select UPS setting >> Parameters setting. Refer to Chart 3-4.
Chart 3-4
9
Note: Different UPSs may access different parameter setting.
1. Select the functions by clicking “Enable” or “Disable” button. Change the
numbers by clicking up-down arrows or modify the numbers directly in
the number column.
2. Click “Apply” button to save the settings. Each function setting is saved
by clicking “Apply” button in each section.
3. Click “Default” button to recover the default setting.
Note: Any functions which are not supported by UPS will not be able to
access.
 Alarm Control: If enabled, UPS alarm will be activated. Vice versa.
 Alarm at bypass mode: If enabled, UPS alarms when it’s working at
bypass mode. Vice versa.
 Alarm at battery mode: If disabled, UPS will not alarm when it’s working
at battery mode. Vice versa.
 Auto reboot: If enabled, UPS will auto recover when AC is recovering.
Vice versa.
 Bypass when UPS is off: If enabled, AC will directly provide power to
connected devices when UPS is off. Vice versa.
 Converter mode: If enabled, the UPS will operate in converter mode.
Vice versa.
 ECO mode: If enabled, the UPS will operate in ECO mode when input
voltage is within acceptable range. Vice versa.
 Battery open status check: If enabled, the monitored UPS will check if
the battery connection is ok or not when UPS is turned on.
 Cold start: If disabled, the UPS can be turned on only when AC is
normally connected to UPS. Vice versa.
 Bypass not allowed: If enabled, the UPS will not transfer to bypass
mode under any conditions. If disabled, the UPS will be allowed to
transfer to bypass mode according to UPS internal setting.
 Battery deep-discharge protection: If enabled, the monitored UPS shuts
down in accordance with the condition of battery and load on battery
mode to protect battery. Vice versa.
 Site fault detection: If enabled, the monitored UPS will beep when the
input neutral and hot wires are reversed. Vice versa.
 P1 Programmable outlet control (battery mode): If enabled, when UPS
is running at battery mode, it will cut off P1 outlets after backup setting
time arrives. If disabled, UPS will provide continuous power to P1
outlets until the battery is running out.
 Outlet setting: Users can set limited backup time for P1 outlets when
UPS is on battery mode.
 Battery numbers setting: Set battery numbers in parallel.
 Voltage and frequency range for bypass mode: Set acceptable voltage
and frequency range in bypass mode
 Maximum and minimum voltage: When UPS is on bypass mode and
10
input voltage is out of setting range, UPS will enter battery mode.
Maximum and minimum frequency: When UPS is on bypass mode
and input frequency is out of setting range, UPS will enter battery
mode.
Voltage range for ECO mode: Set acceptable voltage range for ECO
mode.


3.3
3.3.1.
Control
Real-time control
Select Control >> Real-time control. Refer to Chart 3-5.
Chart 3-5
You can real-time control the UPS by executing following operation:
 UPS turn On/Off: Click “On” to turn on the UPS and “Off” to turn off
the UPS immediately.
 Battery Self-Test: It offers three types of battery self-test:
10-second self-test, deep discharge test, and self-defined self-test.
Simply clicking “Start” button from each type. It will execute the
self-test immediately.
3.4. System configuration
3.4.1.
Web user
It configures the authority to access SNMP web pro. Please enter access ID
and password in each column. There is no limitation to access control in
default setting. It is also allowed for http and https modification. The default
setting is 80 for http and 443 for https. If any modification for adding web
11
users, deleting web users or port re-configuration, it’s necessary to click
“Restart Web Server” button to restart web server to activate all
modifications. Refer to Chart 3-6.
Chart 3-6
If SNMP Manager pops up with "Authentication Required" windows, please
provide default values as above:
User Name: user
Password:
[leave empty]
3.4.2.
E-mail
It’s allowed to send alarm mail by SMTP server. To use this function, the
e-mail service must be correctly configured. All values in this function page
are default empty. This action can’t be executed without the SMTP
information, e-mail account and password. Besides, the sender account
should be allowed for SMTP/POP3 forwarding.
Select System Configuration >> E-mail. Refer to Chart 3-7
12
1.
2.
3.
4.
Chart 3-7
Enter SMTP server, security type (supported encryption from SMTP
server), SMTP port, sender’s E-mail address, user name and
password. Click checkbox of “Need Auth” for password verify.
Enter correct e-mail accounts in Receive list. Then, click “Apply” to
add into receivers list. Click “Delete” button to delete e-mail account.
Click “Apply” to save the changes. The “Test” button can be used to
send a test e-mail to all receivers to confirm correct operation. When
the test e-mails are successfully sent to specific recipients, it will pop
up a successful message on operated PC. Otherwise, it will pop up a
failure dialog to indicate there is an error for parameter setting.
You may decide who will receive daily report e-mail at specific duration.
Please enter recipient's Email Address and timer into columns. Then, click
“Apply” button to set up this action. You also can configure who will
receive alarm e-mail when event log exceeds 100 or data log exceeds 50
records. Please click checkbox of selections.
3.4.3.
SMS
 Sending SMS By Server
It is required to have service software available such as ViewPower Pro.
In the event of an alarm condition occurring, a message about UPS
status will be sent to the specified users via mobile phone. Please refer
to Chart 3-8 b.
 Sending SMS By Serial Port
It is used EMD port as data transmission to send SMS without any
service software. Please configure Baud rate of GSM Modem as 9600
and then connect data transmission port () of SNMP web port card to
GSM Modem with a RJ11 to DB9 cable. Please refer to Chart 3-8 a for
13
detailed wiring.
Chart 3-8 a
Chart 3-8 b
3.4.4.
Wake on LAN
It’s to remotely wake on specific PCs in LAN when these PCs are supported to
Wake-on-LAN (WOL) via a magic packet.
Select System Configuration >> Wake on LAN. Refer to Chart 3-9.
14
Chart 3-9
After MAC addresses of remote PCs are entered into address column, it will
allow to remote control the PCs. However, it’s also required to have
hardware support for remote PCs to implement this function.
3.4.5.
Shutdown
It is to remotely shut down specific PCs with Shutdown Wizard. This function
is only available to integrate with Shutdown Wizard. Please also check user
manual of Shutdown Wizard for the details.
Select System Configuration >> Shutdown. Refer to Chart 3-10.
Chart 3-10
15
3.4.6.
Event action
This function is only available to integrate with Shutdown Wizard. Please
also check user manual of Shutdown Wizard for the details.
Select System Configuration >> Event action. Refer to Chart 3-11.
Chart 3-11






Shutdown the PC while battery mode: When selected, integrated with
Shutdown Wizard, local PC will shut down while UPS works on battery
mode.
Time needed for shutting down the PC: Enter the delay time to shut
down the operating system.
The PC should:
1. Shutdown: When clicking the checkbox, the selected system will
shut down. The default setting is clicked.
2. Sleep mode: When clicking the checkbox, selected system will
suspend the system instead of a normal shutdown. But this function
is only supported by Windows 2000 or higher on supported
hardware.
Also power off the UPS after shutting down the PC: When click the
checkbox, monitored UPS will turn off after local system shuts down. The
UPS shutdown time will be later than system complete shutdown time.
Users can choose to shut down the system without shutting down the
UPS.
Shutdown UPS output after xx sec: It will cut off UPS output after
monitored UPS works on battery mode for xx sec.
Shutdown the PC while low battery: When clicking this checkbox, local
PC will shut down when monitored UPS battery is running low.
16






Wake on LAN while AC recovery: When clicking this checkbox, the local
PC will be wake on LAN while AC recovery.
Send E-mail while any UPS event occurs: When clicking this checkbox, it
will send alarm E-mail when any event occurs on the local UPS.
Send SMS while any UPS event occurs: When clicking this checkbox, in
the event of an alarm condition occurring, a message about UPS status
will be sent to the specified users via mobile phone.
EMD alarming temperature upper limit: Set up alarm for high
temperature point. If detected temperature is beyond setting value, it
will send alarm message.
EMD alarming humidity upper limit: Set up alarm for high humidity point.
If detected humidity is beyond setting value, it will send alarm message.
Data record interval xx sec: Data log record the data per xx sec.
3.4.7.
Scheduled
Select System Configuration >> Scheduled. Refer to Chart 3-12.
Chart 3-12


Scheduled battery self-test: Scheduled battery self-test can be executed
once, daily, weekly, or monthly. Users can select UPS and time
parameters. It is recommended to set only one action in the same time.
If multiple actions have been applied at the same time, some of these
actions may be ignored. Any action will be ignored when the action is not
supported by the UPS.
Scheduled UPS on/off: Scheduled UPS on/off can be executed once,
daily, weekly. Users can select UPS and time parameters. It is
17
recommended to set only one action in the same time. If multiple actions
have been applied at the same time, some of these actions may be
ignored. Any action will be ignored when the action is not supported by
the UPS.
3.4.8.
System time
Select System Configuration >> System time. Refer to Chart 3-13.
Chart 3-13






Automatic time correction interval
Time server: The SNTP server IP address or domain name.
Time Zone (Relative to GMT): It’s measured to relative to GMT.
System Time (mm/dd/yyyy hh:mm:ss): It is to set up SNMP web local
host time
Auto Restart System for Every (0: Disable): XX Minute(s)
Manual Restart system after 30 Seconds: When click “Apply” button,
SNMP will restart after 30 seconds.
3.4.9.
SNMP configuration
Setting SNMP web pro basic information such as IP address, password, trap
IP address, SNMP UDP port, add/delete snmpv3 user account and restore
the factory settings.
Note: Some modifications are required to restart snmp server to become
effective.
Select System Configuration >> SNMP configuration. Refer to Chart 3-14 a
and 3-14 b.
18
Chart 3-14 a
Chart 3-14 b

IP address: There are two methods to obtain IP address
1. Automatically obtain IP address (DHCP, default)
2. Manually configure IP address
The system will default automatically obtain IP addresses. If there is no
this kind of service provided in LAN, the default IP will display as
“192.168.102.230”, Net mask as “255.255.255.0” and default gateway
as “0.0.0.0”.
19




Password: Modify the password. The length of password is 8~15 digits.
Trap IP address: The SNMP device could provide 12 static trap
addresses.
SNMP server configuration: You may change SNMP port and trap port.
You also can add SNMPV3 users by clicking “Add” button. It will pop up a
screen to set up user setting such as security level and permission level.
Refer to below chart.
Restore the factory settings
Note:The system will default automatically obtain IP addresses and
default Password is 12345678.
3.5. Log
3.5.1.
Event log
In the Event Log page, it lists all history events and can be saved as .csv file.
The event log includes UPS warnings, fault info, EMD warnings, UPS
operation logs from web users or ViewPower pro users. All logs are recorded
in flash memory of web card by month. It’s safely recorded without loss even
after power failure occurs. It can save up to over 200,000 threads. Refer to
Chart 3-15.
Select Log >> Event log.
20
Chart 3-15
3.5.2.
Data Log
In the Data Log page, it will list all history logs and can be save as .csv file.
All logs are recorded in flash memory of web card by day. It’s safely recorded
without loss even after power failure occurs. It can save up to over 200,000
threads. Refer to Chart 3-16.
Select Log >> Data log.
Chart 3-16
21
3.6. Help
3.6.1.
Serial Port Debug
It’s to test communication condition between SNMP card and device.
Select Log >> Event log. Refer to Chart 3-17.
Chart 3-17
22